+ All Categories
Home > Documents > AMRITSAR SPECIFICATIONS FOR CUSTOM BUILT KITCHEN...

AMRITSAR SPECIFICATIONS FOR CUSTOM BUILT KITCHEN...

Date post: 20-Mar-2020
Category:
Upload: others
View: 3 times
Download: 0 times
Share this document with a friend
81
GO SPEC CUSTOM BUI D HABITAT ARCHIT SHIROMANI GURD INDIA - 1st & 2nd Floor, Doon Building, Plot No.230 OLDEN TEMPLE AMRITSAR CIFICATIONS FOR ILT KITCHEN EQUIPME Dated: 12/08/2014 ARCHITECT TECTS 1777, MAHARAJ NAGAR, CLIENT DWARA PARBANDHAK COMMIT 0, Block A - 2, Sector - 17, Dwarka, New Delhi - 110078, Ph no ENT LDH. TTEE. o: + 91 - 011 - 43505228/29
Transcript
Page 1: AMRITSAR SPECIFICATIONS FOR CUSTOM BUILT KITCHEN …sgpc.net/wp-content/uploads/2013/07/CUSTOM-BUILT... · INDIA Sector -17, Dwarka, New Delhi -110078 GENERAL SPECIFICATIONS FOR CUSTOM

GOLDEN TEMPLE

AMRITSAR

SPECIFICATIONS FOR

CUSTOM BUILT KITCHEN EQUIPMENT

Dated: 12/08/2014

ARCHITECT

HABITAT ARCHITECTS 1777, MAHARAJ NAGAR, LDH.

CLIENT

SHIROMANI GURDWARA PARBANDHAK COMMITTEE.

INDIA - 1st & 2nd Floor, Doon Building, Plot No.230, Block A - 2, Sector - 17, Dwarka, New Delhi - 110078, Ph no: + 91 - 011 - 43505228/29

U.A.E - Dubai Airport Free Trade Zone, 3rd East Wing Building, 4th Floor, P.O Box- 54620, Dubai 54620, U.A.E, Ph no: +971-563738349

[email protected], www.hpgconsulting.com

GOLDEN TEMPLE

AMRITSAR

SPECIFICATIONS FOR

CUSTOM BUILT KITCHEN EQUIPMENT

Dated: 12/08/2014

ARCHITECT

HABITAT ARCHITECTS 1777, MAHARAJ NAGAR, LDH.

CLIENT

SHIROMANI GURDWARA PARBANDHAK COMMITTEE.

INDIA - 1st & 2nd Floor, Doon Building, Plot No.230, Block A - 2, Sector - 17, Dwarka, New Delhi - 110078, Ph no: + 91 - 011 - 43505228/29

U.A.E - Dubai Airport Free Trade Zone, 3rd East Wing Building, 4th Floor, P.O Box- 54620, Dubai 54620, U.A.E, Ph no: +971-563738349

[email protected], www.hpgconsulting.com

GOLDEN TEMPLE

AMRITSAR

SPECIFICATIONS FOR

CUSTOM BUILT KITCHEN EQUIPMENT

Dated: 12/08/2014

ARCHITECT

HABITAT ARCHITECTS 1777, MAHARAJ NAGAR, LDH.

CLIENT

SHIROMANI GURDWARA PARBANDHAK COMMITTEE.

INDIA - 1st & 2nd Floor, Doon Building, Plot No.230, Block A - 2, Sector - 17, Dwarka, New Delhi - 110078, Ph no: + 91 - 011 - 43505228/29

U.A.E - Dubai Airport Free Trade Zone, 3rd East Wing Building, 4th Floor, P.O Box- 54620, Dubai 54620, U.A.E, Ph no: +971-563738349

[email protected], www.hpgconsulting.com

Page 2: AMRITSAR SPECIFICATIONS FOR CUSTOM BUILT KITCHEN …sgpc.net/wp-content/uploads/2013/07/CUSTOM-BUILT... · INDIA Sector -17, Dwarka, New Delhi -110078 GENERAL SPECIFICATIONS FOR CUSTOM

Integrated Solution for Hospitality ProjectsAn ISO 9001:2000 Certified Company

CB. K. Eqpt /Specs GOLDEN TEMPLE - AMRITSAR Page- 2of 81INDIA Sector -17, Dwarka, New Delhi -110078

www.hpgconsulting.com

PREAMBLE

The tenders being invited are for Golden Temple Amritsar.

The following tender specifications are included:

Custom Built Kitchen Equipment

The bidders are required to follow the instruction given and return the said document duly filled in withrates.

The Following is to be mentioned in the envelope “Quotation custom built kitchen equipment forGolden Temple Amritsar.”

Quotations should be in the name of:---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------A copy of the Quotation to be sent to:HPG CONSULTING1st and 2nd Floor, Doon Building,Plot No.230, Sector-17, Dwarka,New Delhi- 110078

The owners reserve the right to reject any tender or a part of tender without giving any reason and do notbind themselves to accept lowest or any tender.

The owners will not be responsible for, nor pay for any expenses or losses, which may be incurred by thebidders in preparation and submission of the tender.

Before the acceptance of any offer, visits may be made by the owners or consultants to the bidders workto inspect the facilities and satisfy themselves on technical and operational matters. The bidders shallafford whatever assistance is required in this process.

Page 3: AMRITSAR SPECIFICATIONS FOR CUSTOM BUILT KITCHEN …sgpc.net/wp-content/uploads/2013/07/CUSTOM-BUILT... · INDIA Sector -17, Dwarka, New Delhi -110078 GENERAL SPECIFICATIONS FOR CUSTOM

Integrated Solution for Hospitality ProjectsAn ISO 9001:2000 Certified Company

CB. K. Eqpt /Specs GOLDEN TEMPLE - AMRITSAR Page- 3of 81INDIA Sector -17, Dwarka, New Delhi -110078

www.hpgconsulting.com

GENERAL SPECIFICATIONS FOR CUSTOM BUILD EQUIPMENTS

STAINLESS STEEL:

Where stainless steel is specified it shall be what is known to the trade as Austenitic 18-B type 304, 2Bfinish, with content from 17% to 19% chrome, 7 % to 9% nickle and a maximum carbon content of 0.11.

Stainless steel shall be free from scale and surfaces should be polished to a no. 4 commercial finish.

STAINLESS STEEL PIPE AND TUBING:

Seamless tubing shall be thoroughly and properly ground smooth and finished to match adjacent work. Alltubing where exposed to view shall be given a final grand of not less then 180 grit emery.

STRUCTURAL STEEL SHAPES:

All angles, band, channels or other structural shapes used for framing shall be of domestic manufactureuniform and ductile in quality, free of hard spots, runs, checks or cracks or other surface defects. Wheresuch sections are specified as S.S. or tinned by the hot dip process, with all fluxes removed.

HANDLES, BRACKETS, LOCKING DEVICES AND HARD WARE:

Wherever equipments are provided with handles, knobs, hinges, brackets or other misc. hardware all shallbe either of heavy stain finish chrome plated brass or stainless steel.

All drawers, enclosed cabinets, refrigerators storage bins, shall be furnished with extra heavy duty securitytype locking devices of cylinder type, chrome plated.

FASTENINGS:

Welds, bolts screws, nuts and washers shall be of steel, except where brass or stainless steel is fastened,in which case they shall be of brass or stainless steel respectively. Where dissimilar metals are fastened,bolts, screws and nuts shall be of the highest grade metal. The spacing and extent of welds, bolts andscrews shall be such as to ensure suitable fastenings and prevent bulging of the material fastened andshould not be exposed.

WELDING:

All welding shall be done by the electrical fusion, metal –arc method. Carbon-arc or gas welding will not bepermitted. All welding shall be done in a thorough manner, with welding rod of some composition as sheetsor parts welded. Welds shall be complete welds, strong and ductile, with excess metal ground off jointsfinished smooth to match adjoining sheet surfaces. All joints in top of fixtures, tables, drain boards;exposed shelving, sinks etc. shall be welded. All equipment here in specified which is constructed in more

Page 4: AMRITSAR SPECIFICATIONS FOR CUSTOM BUILT KITCHEN …sgpc.net/wp-content/uploads/2013/07/CUSTOM-BUILT... · INDIA Sector -17, Dwarka, New Delhi -110078 GENERAL SPECIFICATIONS FOR CUSTOM

Integrated Solution for Hospitality ProjectsAn ISO 9001:2000 Certified Company

CB. K. Eqpt /Specs GOLDEN TEMPLE - AMRITSAR Page- 4of 81INDIA Sector -17, Dwarka, New Delhi -110078

www.hpgconsulting.com

then one piece of sheet of metal, shall be continuously Welded together with welds ground smooth andpolished. But welds made by spot welding straps under beams and filling in the voids with solder andfinished by grinding, will not be accepted.

It is the intention of this specification that all welded joints shall be homogenous with the sheet metalitself. Where sheet sizes necessitate a joint, such a joint shall be welded. Tops of fixtures shall befabricated in the factory with welded joints to reduce field joints to a minimum. Where fixtures joins thetops of such fixtures Shall be continuous with welded joints except in the case of field joints. Al joints madein the field shall be closely butted, pulled together in the field, field welded and polished smooth inaccordance with section. Grinding, polishing finishing if these requirements. Tops of fixtures shall be ofmaximum length and with welded factory joints to an absolute minimum. Wherever welds occur on thesurfaces not finished by grinding & polishing, such welds sand the accompanying discoloration shall besuitably coated in the factory by means of metallic base paint. To prevent the possibility of progressivecorrosion of such joints.

GRINDING, POLISHING, AND FINISHING:

All welded exposed joints shall be suitably ground flush with adjoining material and neatly finishharmonizing herewith. Wherever material has been sunken or depressed by the welding operation, suchdepression will be suitably hammered and pressed flush to adjoining surfaces and if necessary againground to eliminate low spots. All ground surfaces shall then be polished or buffed to match adjoiningsurfaces, consistent with good workmanship. Care shall be exercised in all grinding operations to avoidexcessive heating of metal & metal discoloration. In all cases, grain of rough grinding shall be removed bysuccessive polishing operations. Texture of final polishing operation shall be uniform and smooth consistentwith reasonable care and good workmanship. General finish of all equipment shall be of high grade.

But joints and contact joints, wherever they occur, shall be close fitting and shall not require solder as filler.In no case in any soldering for strength and stability of joint and fixture itself. Wherever breaks bend occur,it shall be free from undue extrude and shall not be flaky scaly or cracked in appearance and where suchbreak work does mar the uniform surface appearance of the material. All such marks shall be removed bysuitably grinding, polishing and finishing. Wherever shared edges occur they shall be free from burrs, finsor irregular projections and shall be finished over such sheared edges. Where mitres are bull nosed cornersoccur they shall be neatly finished with under edge of material neatly ground to a uniform condition and, inno case any over lapping materials to be accepted.

It is the intention of these specifications to cover equipment of quality finish consistent with high grademanufacturing practices. All exposed surfaces shall be of no 4 finish expect trim, which is to be more highlypolished satin finish. Where specified all doors cabinets, shelves, whether inside /outside of cabinets andwherever exposed are to be no. four 4 finish. This applies to inside finish of any cabinet having door s orotherwise an exposed surface shall be interpreted as meaning an inside surface exposed to view when asliding or swinging door is opened. Underside of shelf need not to be 4 finishes but such finish shall be at

Page 5: AMRITSAR SPECIFICATIONS FOR CUSTOM BUILT KITCHEN …sgpc.net/wp-content/uploads/2013/07/CUSTOM-BUILT... · INDIA Sector -17, Dwarka, New Delhi -110078 GENERAL SPECIFICATIONS FOR CUSTOM

Integrated Solution for Hospitality ProjectsAn ISO 9001:2000 Certified Company

CB. K. Eqpt /Specs GOLDEN TEMPLE - AMRITSAR Page- 5of 81INDIA Sector -17, Dwarka, New Delhi -110078

www.hpgconsulting.com

least equal to 80-ground finish. Final no. 4 finishes to be factory finish, not as furnished by mill. Indicationof die markings not blending with final finish will not be accepted.

BOLT CONSTRUCTION:

It is the intention of this specification that all equipment on exposed surfaces and wherever bolts are usedto fasten trim to paneling and body of warmers, cabinets, counters etc. and more particularly to fastentops of counter, dish tables etc. to top of framing such bolts and screws occur on the inside of the fixturesand are either visible or might come in the contact of the hands or the wiping cloth, such bolts, screwsshall be capped with a suitable lock washer and chrome plated, brass or bronze acorn nut . Where screwnuts are not visible or readily accessible, they may be capped with a standard lock washer & steel nuttreated to prevent rusting & corroding. Wherever bolts and screws are welded to underside of trim or tops,the revere side of weld shall be f\neatly finished uniform with the adjoining surface of trim or top,depressions at these points will not be acceptable.

SOUND DEADENING:

Underside of all stainless steel top for tables, counters, sink dishes and pot table with angle frameworkshall be treated with a coating of Carbozite aluminum finish or approved equal.

MATERIAL AND WORKMANSHIP:

All material equipment etc. shall be new and of kind specified and shall be in undamaged condition whenturned over to owner. All workmanship shall be of best quality of crafts men skilled in their respectivetrades. Appliances shall be of rigid construction free from objectionable vibrations and quiet in operation.Manufacture’s nameplate shall not appear on any of the fabricated equipment.

RESERVATIONS:

Various items are specified here in with the model no., brand or trade names or name of manufacturer,and it is the intent of this specification that the exact fixture so specified shall be furnished. This is notintended to restrict competition and consideration will be given to other brands that are equal or superioron every respect. However no substitutes or alternatives will be accepted if not mentioned in the base bid.

Owner reserve right to waive any information or reject any or all bids or any part or parts thereof, or toaccept that bid as a whole or part, which in his judgment is for the interest of the owner.

The decision as to acceptance or rejection of any alternate proposed shall be that of owner and / orarchitect or his consultant and their decision shall be final.

Page 6: AMRITSAR SPECIFICATIONS FOR CUSTOM BUILT KITCHEN …sgpc.net/wp-content/uploads/2013/07/CUSTOM-BUILT... · INDIA Sector -17, Dwarka, New Delhi -110078 GENERAL SPECIFICATIONS FOR CUSTOM

Integrated Solution for Hospitality ProjectsAn ISO 9001:2000 Certified Company

CB. K. Eqpt /Specs GOLDEN TEMPLE - AMRITSAR Page- 6of 81INDIA Sector -17, Dwarka, New Delhi -110078

www.hpgconsulting.com

WORKING TOP/COUNTER TOP

Where work top and counter top is specified shall be constructed of 16/14 GA S.S., profile as per standardshop drg.

CEILING HUNG SHLEF.

Where ceiling hung shelf specified shall be constructed of 18 GA S.S., With front turned down 40mm & in12mm , Rear and both sides turned up 50mm & hemmed.

LEGS:

All legs to be constructed of not less then 40mm diameter stainless steel tubing cold drawn, annealed andpickled spaced no more than 1800mm C.C. all legs shall be uniform in finish. All legs, until and unlessspecified, to be of 304 SS.

LEGS CROSS BRACING:

All legs bracing where required, to be constructed of not less then 25 mm diameter 18GA SS and asspecified above for expect as noted below. All cross bracing to run horizontal between all legs,approximately 250 mm above floor unless otherwise specified. All joints to be completely welded aroundentire perimeter forming complete seal with all welds ground and painted. Where one side of box unit iseliminated to provide space for cans, carts, plumbing or otherwise single cross brace to extent to givenlegs, such cross brace to be reinforced by diagonal section of tubing and set not less then 150mm out ateach side, all welded as specified herein before.

UNDER BRACING:

All stainless steel counters, tables boards and dish tables tops to be braced below with inverted typechannels made of 16 GA SS as specified, measuring 25 mm X 100mm X 25mm spaced not more than 750mm on centers and installed in similar fashion.

FEET:

All legs shall be provided with stainless steel bullet feet, having an integrally formed shaft, with a minimumadjustment of approx. 40mm without using of threading or adjusting bolts. Feet shall be completely sealedat bottom and shall be close fitting between tubular legs support and foot.

CASTORS:

All the castors shall be corrosion resistant, non-marking rubberized with precision ball bearing. All thecastors shall be able to hold 250 Kg each. Shall be swivel/ fixed type or with break or with out breakmentioned in the tender. The make shall be equivalent to TENTE.

Page 7: AMRITSAR SPECIFICATIONS FOR CUSTOM BUILT KITCHEN …sgpc.net/wp-content/uploads/2013/07/CUSTOM-BUILT... · INDIA Sector -17, Dwarka, New Delhi -110078 GENERAL SPECIFICATIONS FOR CUSTOM

Integrated Solution for Hospitality ProjectsAn ISO 9001:2000 Certified Company

CB. K. Eqpt /Specs GOLDEN TEMPLE - AMRITSAR Page- 7of 81INDIA Sector -17, Dwarka, New Delhi -110078

www.hpgconsulting.com

UNDERSHELVES:

Where flat under shelving is specified under shelves shall be constructed of 18 GA SS All shelving shall beturned down on all sides approx. 40mm and in 12mm in channel shape with resulting corners cut out to fitcontour of leg. Shelving shall be welded to legs and shall be ground polished & smooth under shelving shallm be reinforced with 25 mm X 100 mm X 25 mm of 16GA SS welded channels.

Removable type shelving to be of same material, rolled down on all sides with corners notched to counterof leg with resultant notches ground and polished smooth. Under shelving to be constructed in sections ofnot more than 900 mm and where butted against adjoining shelf section shelving to be turned down 40mm and in 12 mm in channel shape. Supporting channel to be furnished on underside of each self-sectionof same size and material as specified above.

DRAWERS:

Drawers inserts shall be constructed of 18 GA SS as per GN. 1/1 pan, 100 mm deep. Complete with lockingarrangement and integral handle, all drawers complete with GN. 1/1 pan 100mm deep.

SINKS AND DRAIN BOARDS:

All sinks and drain boards to be constructed of 16 GA SS unless otherwise specified with all joints neatlywelded ground and polished smooth. No soldering at any point will be accepted in sink and drain boardconstruction. All front and free standing edges to be turned up 40mm and to be turned out 50mm anddown 40mm in 12mm raised fronts and ends of drain board are to be level with sink and continuoustherewith and is not to follow pitch of drain boards. Drain boards to be pitched 3mm X 25 mm towards sinkcompartment. Sinks and drain boards to have 250mm high splash back level and continuous not followingpitch of drain boards adjacent to walls or adjoining equipment. Where drain boards exceed 600 mm inlength legs shall be provided as here in before specified. All vertical and horizontal corners to be roundedto radius of approx. 25 mm with all intersections meeting in spherical section. All sinks having two or morecompartments to have double dividing partitions, with fully rounded corners, both vertical & horizontal. Allcorners of drain boards to be rounded on insides to a radius of 25 mm front corners of rolled rim to be fullyrounded on outside rolls and be concentric with inside of roll. Bottom of each sink compartment to becreased to sufficient pitch towards waste outlet with 100 mm 14 GA SS perforated removable strainer plateset not less then 3/8” below sink bottom. Opening for hot & cold-water faucets to be cut in to splash backas required. All sinks shall be 14 GA deep unless otherwise specified to a no. 4 satin finish.

Where sinks are to be built as a part of counters, overflow scrap compartments for sinks as indicated onplans, to be constructed sane as above, welded into place, with resulting weld s ground and polishedsmooth, eliminating traces of welding.

Page 8: AMRITSAR SPECIFICATIONS FOR CUSTOM BUILT KITCHEN …sgpc.net/wp-content/uploads/2013/07/CUSTOM-BUILT... · INDIA Sector -17, Dwarka, New Delhi -110078 GENERAL SPECIFICATIONS FOR CUSTOM

Integrated Solution for Hospitality ProjectsAn ISO 9001:2000 Certified Company

CB. K. Eqpt /Specs GOLDEN TEMPLE - AMRITSAR Page- 8of 81INDIA Sector -17, Dwarka, New Delhi -110078

www.hpgconsulting.com

Bottom of each sink compartment to be furnished with 50 mm IPS heavy-duty lever drain. Unlessotherwise noted, connected overflow to be furnished with SS perforated plates secured to body of sinksand constructed so that constant water level is 25 mm below dividing partition.

DISH TABLE:

Dish table to be constructed to be same as previously specified for sink drain boards except as notedbelow. Where table enter dish washing machine or pot washing they shall be turned down 25 mm intomachine and a flange provided at both front and splash back, arranged so as to permit a neoprene gasket,approx. 3mm thick, being bolted between flanges and turned down of table forming a watertight jointacross bottom and if up both side to top edge of dish table. Under side of all dish table shall be providedwith sound deadening material either sprayed or brushed on into smooth coating. Sound deadening to beCarbozite or equal and finished sprayed with aluminum.

STAINLESS STEEL TABLE TOPS:

Where SS tops are called for they shall be of not less then 16 GA SS finished in satin finish with all resultingedges rounded with no burrs or other excess material left. Where tables are placed against building wallsthey are to be turned up in back approx. 150 mm and returned 25 mm 90 at wall with all exposed endsclosed.

Vertical and horizontal joints to be coved on 20mm radius terminating in fully coved intersectionsthoroughly welded, ground and polished smooth to match top surfaces.

Top shall be constructed of single pieces of S.S and to be reinforced underneath with inverted typechannels of not less then 16 GA G.I or S.S as noted above, space not more than 750 mm C.C. tables 1800mm and longer to have 40 X 40 X 3mm steel angle frame work reinforced outside edges with crosschannels over 750 mm or less.

SLIDING DOORS:

Sliding doors where called for, to be made of18 GA SS exterior and 20 GA S.S. interior unless otherwisespecified. Doors to be equipped with recessed stainless steel pull handles. Door to be made removable.Door to be double pan construction, filled with suitable sound deadener, 12 mm thick with all cornerswelded ground and polished smooth to uniform finish. Doors to be designed to permit removal for cleaningand adjustment without use of tools. Bolts and screws are to be kept to minimum and to be of corrosionresisting metal. Spacers where not exposed to view may be of 14 GA, 20 mm diameter upper suspensionnylon rollers to be heavy duty and ground to minimize wear and noise. Precaution to be taken in all casesto avoid friction and rubbing between doors, door suspension and upper sliding framework includinghardware.

Page 9: AMRITSAR SPECIFICATIONS FOR CUSTOM BUILT KITCHEN …sgpc.net/wp-content/uploads/2013/07/CUSTOM-BUILT... · INDIA Sector -17, Dwarka, New Delhi -110078 GENERAL SPECIFICATIONS FOR CUSTOM

Integrated Solution for Hospitality ProjectsAn ISO 9001:2000 Certified Company

CB. K. Eqpt /Specs GOLDEN TEMPLE - AMRITSAR Page- 9of 81INDIA Sector -17, Dwarka, New Delhi -110078

www.hpgconsulting.com

NOTE:

Double doors to be provided with double overhead tracks and carriers for maximum clear door opening.Units to be provided with trackless bottom with concealed guide for overhead roller doors. Guides to beequipped with limit stops and to prevent telescoping of doors.

HINGED DOORS:

Hinged doors for cabinets, counter etc. to be constructed of 18 GA SS with ground and polished smooth.Hinges catches and locking devices to be chrome plated brass. Hinges to be of construction as to eliminateexposed bolts and screw heads. Doors handles to be provided and to be SS as here in after specified.

COUNTER, CABINET AND OVERHEAD SHELVES:

Counter shelves and cabinet shelves to be constructed of 18 GA SS. Overhead cabinets shelve to beconstructed of 18 GA SS. All shelving is to be removable type, finished in satin finish and constructed insections of not more than 750 mm. where shelves are more than 1500mm above floor, underside of shelfto be finished same as top. All shelves to be removable for easy cleaning. Plate warmer shelves to beperforated and removable.

UNTENSIL RACK:

Units to be measured approx. 600mm wide X length as shown on plan, constructed of 50mm X 6mm SSbond with ends fully rounded, one piece welded construction, ground and polished smooth to uniformfinish. Center rails to be located approx. 250 mm below outer rails and secured b means of welded V shapebraces constructed of same material. Pothooks to be sliding type, positioned 150 mm CC for both upperand lower rails.

Units to be hung from ceiling slab by means of 50 mm X 6mm SS band hangers with cross bracing toprevent swaying. Supports to be secured to racks by means of SS round heads, bolts and acorn nuts withlock washers. Top of ceiling hangers when not exposed to be secured to a 12 S.S. channel, which shall beanchored to ceiling slab in an approved manner. If supporting channels are exposed they are to beconstructed of 12 GA SS secured to finish ceiling in approved manner.

Revolving utensil racks to be a here in after specified and in accordance with details shown on drawings.

WALL CABINETS:

To be of length as shown on plans or which are specified, 325mm deep and 750mm high except whereshown otherwise on drawing. All cabinets to have sloped dust proof tops. Exterior bottom to be a flushtype construction.

Page 10: AMRITSAR SPECIFICATIONS FOR CUSTOM BUILT KITCHEN …sgpc.net/wp-content/uploads/2013/07/CUSTOM-BUILT... · INDIA Sector -17, Dwarka, New Delhi -110078 GENERAL SPECIFICATIONS FOR CUSTOM

Integrated Solution for Hospitality ProjectsAn ISO 9001:2000 Certified Company

CB. K. Eqpt /Specs GOLDEN TEMPLE - AMRITSAR Page- 10of 81INDIA Sector -17, Dwarka, New Delhi -110078

www.hpgconsulting.com

Cabinets to be constructed of 18 GA SS of all welded construction. Cabinet interiors to be provided withfixed bottom shelf and two removable, adjustable, intermediate shelves. Shelves to rest on clips, whichshall be secured to keyhole strips fastened to interior of cabinet. Doors to be of double wall constructionfully sound proof, constructed in accordance with details here in before set forth.

SINKS SET INTO WORK COUNTERS OR WORK TOPS:

Sinks to be constructed if same gauge and material as specified for counter top.

Tops perimeter of each sink to be continuously electrically welded to the edge of opening in table orcounter top with resulting welds ground and polished smooth so that sink and top are integral units. Tableor counter tops to be punched to receive 20 mm faucets.

All sinks to have vertical and horizontal corners rounded on 25 mm radius with bottom punched to 40mmor 50mm waste outlet depending on which is indicated in drawings.

Sinks to be finished and appearance to be same as table or counter tops.

BAIN MARIES (ELECTRIC)

To be of some construction as here in before specified as above except that the bottom of the units will notbe provided with the steam coils. Bottom of units for electric operation will be furnished with emersionheating elements of size as shown on drawings. Complete with control knob, thermostatic sleeve and dialsetting for temperature desired. Immersion heating element to be as manufactured by Escorts Ltd. Orapproved equal. False bottom to be constructed to clear immersion heating element.

Cold pans are to be 150 mm deep and to be of size and shape as shown on the drawings with each coldpan section constructed as integral part of the counter.

Cold pans to be constructed of 16 GA SS with all vertical horizontal corners coved with serpentine coolingcoils sweated to exteriors. Unit to be insulated on all four sides and bottom with 50 mm of cork set inglycol emulsion. Exterior lining to be of 18 GA S.S. iron with resulting joints fully welded. Top of counter tobe flanged down 12 mm and out 12mm into cold pan and counter top. Bottom of pan to be pitched to25mm chrome plated brass waste outlet.

COUNTER/TABLES SPLASH

All Counter/Tables & Refrigerator Splash same material of top with turned up 150mm(Specified) returned25mm & down 12mm & Rear Gap of splash closed with no. 20 G.A S.S Sheet.

Page 11: AMRITSAR SPECIFICATIONS FOR CUSTOM BUILT KITCHEN …sgpc.net/wp-content/uploads/2013/07/CUSTOM-BUILT... · INDIA Sector -17, Dwarka, New Delhi -110078 GENERAL SPECIFICATIONS FOR CUSTOM

Integrated Solution for Hospitality ProjectsAn ISO 9001:2000 Certified Company

CB. K. Eqpt /Specs GOLDEN TEMPLE - AMRITSAR Page- 11of 81INDIA Sector -17, Dwarka, New Delhi -110078

www.hpgconsulting.com

Submissions along with Quotation

o Soft and hard copy of the catalogues of the equipments quoted.

o Soft copy of the technical Data sheet.

o Any Deviation in specification from the tender needs to be broughtto our notice at the time of submission of quotation.

Quotation will not be considered if any of the above is not submittedalong with quotations.

Page 12: AMRITSAR SPECIFICATIONS FOR CUSTOM BUILT KITCHEN …sgpc.net/wp-content/uploads/2013/07/CUSTOM-BUILT... · INDIA Sector -17, Dwarka, New Delhi -110078 GENERAL SPECIFICATIONS FOR CUSTOM

Integrated Solution for Hospitality ProjectsAn ISO 9001:2000 Certified Company

CB. K. Eqpt /Specs GOLDEN TEMPLE - AMRITSAR Page- 12of 81INDIA Sector -17, Dwarka, New Delhi -110078

www.hpgconsulting.com

GOLDEN TEMPLE - AMRITSARBILL OF QUANTITY FOR CUSTOM BUILT KITCHEN EQUIPMENT

ITEM QTY DESCRIPTION UNIT AMOUNTNO. RATEBASEMENT FLOORRECEIVING AREAR-02 1 WEIGHING TABLE W/DRAWERR-04 1 WORK TABLE W/SINKR-05 3 HAND WASH SINK UNITR-06 11 MOBILE PLATFORM TROLLEYR-07 4 DRINKING WATER SINKR-08 13 POTATO ONION STORAGE BINSR-09 3 FLUSHING HOSE UNITR-16 2 GARBAGE CANFOOD & GENERAL STOREFS-15 2 FLUSHING HOSE UNITGROUND FLOORHOT FOOD PREP AREAK-01 8 SINGLE BURNER STOCK POT RANGEK-01A 4 POT FILLERK-08 1 SPREADER TABLEK-09 13 SPREADER TABLEK-12 1 S.S SERVICE CONSOLEK-15 1 S.S SERVICE CONSOLEK-20 2 DRINKING WATER SINKK-21 9 FLUSHING HOSE UNITK-24 4 DAL WASHING MACHINEK-25 6 GARBAGE CANK-28 6 HAND WASH SINK UNITK-32 4 WORK TABLEK-33 1 WORK TABLEK-35 7 HOT BAIN MARIE COUNTER FOR FOOD HOLDINGK-36 4 MOBILE G.N PAN TROLLEYK-42 9 MOBILE POT RACKSPOT WASH AREAK-44 7 MOBILE POT RACKSWASHING AREAK-49 14 DIRTY/CLEAN DISH TROLLEYK-54 5 GARBAGE CANK-59 1 FLUSHING HOSE UNIT

Page 13: AMRITSAR SPECIFICATIONS FOR CUSTOM BUILT KITCHEN …sgpc.net/wp-content/uploads/2013/07/CUSTOM-BUILT... · INDIA Sector -17, Dwarka, New Delhi -110078 GENERAL SPECIFICATIONS FOR CUSTOM

Integrated Solution for Hospitality ProjectsAn ISO 9001:2000 Certified Company

CB. K. Eqpt /Specs GOLDEN TEMPLE - AMRITSAR Page- 13of 81INDIA Sector -17, Dwarka, New Delhi -110078

www.hpgconsulting.com

GOLDEN TEMPLE - AMRITSARBILL OF QUANTITY FOR CUSTOM BUILT KITCHEN EQUIPMENT

ITEM QTY DESCRIPTION UNIT AMOUNTNO. RATEK-62A 4 DISH WASHING STATION - MANUALK-63 1 WASTE REMOVABLE TABLEFIRST FLOORHOT FOOD PREP AREASK-01 6 SINGLE BURNER STOCK POT RANGESK-01A 3 POT FILLERSK-05 2 MOBILE WORK TABLESK-08 1 HAND WASH SINK UNITSK-09 1 FLUSHING HOSE UNITPOT WASH AREASK-11 5 MOBILE POT RACKSSK-13 1 GARBAGE CANCOMMISSARY KITCHENCK-01 8 RAW FOOD TRANSPORT TROLLEYCK-04 3 HAND WASH SINK UNITCK-05 7 FOOD TRANSPORT TROLLEYCK-15 2 FLUSHING HOSE UNITCK-17 2 DRINKING WATER SINKCK-18 3 MOBILE G.N PAN TROLLEYCK-20 27 FOOD TRANSPORT TROLLEYCK-21 3 GARBAGE CANCK-22 7 HOT BAIN MARIE COUNTER FOR FOOD HOLDINGSECOND FLOORCHAPATI MAKING AREACM-03 1 WORK TABLE W/SINKCM-05 1 WORK TABLE W/SINKCM-06 1 WORK TABLE W/SINKCM-07 1 WORK TABLECM-08 1 WORK TABLECM-09 1 WORK TABLECM-15 4 GRIDDLE PLATECM-22 4 HAND WASH SINK UNITCM-23 1 GRIDDLE PLATECM-25 1 GRIDDLE PLATECM-29 10 GARBAGE CANCM-30 5 S.S SERVICE CONSOLE

Page 14: AMRITSAR SPECIFICATIONS FOR CUSTOM BUILT KITCHEN …sgpc.net/wp-content/uploads/2013/07/CUSTOM-BUILT... · INDIA Sector -17, Dwarka, New Delhi -110078 GENERAL SPECIFICATIONS FOR CUSTOM

Integrated Solution for Hospitality ProjectsAn ISO 9001:2000 Certified Company

CB. K. Eqpt /Specs GOLDEN TEMPLE - AMRITSAR Page- 14of 81INDIA Sector -17, Dwarka, New Delhi -110078

www.hpgconsulting.com

GOLDEN TEMPLE - AMRITSARBILL OF QUANTITY FOR CUSTOM BUILT KITCHEN EQUIPMENT

ITEM QTY DESCRIPTION UNIT AMOUNTNO. RATECM-38 21 DUNNAGE RACKCM-41 5 DRINKING WATER SINKCM-42 1 WORK TABLECM-43 1 WORK TABLE W/SINKCM-44 6 FLUSHING HOSE UNITCM-46 2 VEG PICK UP TROLLEYCM-47 10 VEG WASHING TROLLEYCM-47A 10 VEG CRATE SOAKING MOBILE RACKCM-51 1 FLUSHING HOSE UNITCM-53 4 MOBILE SANITIZER TROLLEY

Page 15: AMRITSAR SPECIFICATIONS FOR CUSTOM BUILT KITCHEN …sgpc.net/wp-content/uploads/2013/07/CUSTOM-BUILT... · INDIA Sector -17, Dwarka, New Delhi -110078 GENERAL SPECIFICATIONS FOR CUSTOM

Integrated Solution for Hospitality ProjectsAn ISO 9001:2000 Certified Company

CB. K. Eqpt /Specs GOLDEN TEMPLE - AMRITSAR Page- 15of 81INDIA Sector -17, Dwarka, New Delhi -110078

www.hpgconsulting.com

ITEM NO: R-02 WEIGHING TABLE W/DRAWER

QUANTITY: 1 Tentative Image

CUSTOM BUILT

SIZE

Width:

1800mm

Depth:

700 mm

Height:

850 mm

CAPACITY

M.E.P REQUIREMENT SPECIFICATIONS

PLUMBING : For construction detail refer standard shop drawing no. :-HPG/FD/01-A.

#16 Ga. S.S. Top.

Rear Side 150mm High Splash.

Front & both side turned down 50 mm & in 12mm

Rear side turned up 150 mm returned 25 mm & in 12mm.

Top secured to 38mm x 38mm x 3mm thick S.S. weldedangle frame work.

25mm dia S.S. pipe cross bracing welded to legs at Rear &both sides. Front open for Garbage Can.

Six (6) no. 38mm Dia S.S. legs with adjustable bullet feet.

Unit provided One (1) no. tool Drawer at Left side,Construction as per standard drg.

Cold ∅ NA

Hot ∅ NA

Waste ∅ NA

ELECTRIC :

Power NA

Voltage NA

EXHAUST

NA

GAS:

BTU NA

Con. ∅ NA mm

ACCESSORIES:

SPECIAL NOTE: All Sheet /Pipe S.S. 304 Grade Pre-polished Plastic Coated.

Page 16: AMRITSAR SPECIFICATIONS FOR CUSTOM BUILT KITCHEN …sgpc.net/wp-content/uploads/2013/07/CUSTOM-BUILT... · INDIA Sector -17, Dwarka, New Delhi -110078 GENERAL SPECIFICATIONS FOR CUSTOM

Integrated Solution for Hospitality ProjectsAn ISO 9001:2000 Certified Company

CB. K. Eqpt /Specs GOLDEN TEMPLE - AMRITSAR Page- 16of 81INDIA Sector -17, Dwarka, New Delhi -110078

www.hpgconsulting.com

ITEM NO: R-04 WORK TABLE W/SINK

QUANTITY: 1 Tentative Image

CUSTOM BUILT

SIZE :

Width:

1350 mm

Depth:

700 mm

Height:

850 mm

CAPACITY

M.E.P REQUIREMENT SPECIFICATIONS

PLUMBING : For construction detail refer standard shop drawing no. :-HPG/FD/13.

#16 Ga. S.S. Top.

150mm High Rear Side Splash.

Front & both sides turned down 50 mm & in 12mm

Rear side turned up 150 mm returned 25 mm & in 12mm.

Top secured to 38mm x 38mm x 3mm thick S.S. weldedangle frame work.

Left of unit One (1) no. 450mm x 450mm x 200mm deep #16 Ga. S.S. sink, Sink Complete with 50mm dia lever handleoperated waste outlet & rear connected overflow.

Four (4) no. 38mm Dia S.S. legs. With adjustable bulletfeet.

25mm Dia S.S. pipe cross bracing welded to legs at Rear &both sides. Front open for garbage can.

# 20 G.A S.S Apron front of Sink.

One (1) No. Deck Mounted “Jaksons Make” Swivel typewater Mixer faucet.

Cold ∅ ½”

Hot ∅ ½”

Waste ∅ 2”

ELECTRIC :

Power NA

Voltage NA

EXHAUST

NA

GAS:

BTU NA

Con. ∅ NA mm

ACCESSORIES:

SPECIAL NOTE: All Sheet /Pipe S.S. 304 Grade Pre-polished Plastic Coated.

Page 17: AMRITSAR SPECIFICATIONS FOR CUSTOM BUILT KITCHEN …sgpc.net/wp-content/uploads/2013/07/CUSTOM-BUILT... · INDIA Sector -17, Dwarka, New Delhi -110078 GENERAL SPECIFICATIONS FOR CUSTOM

Integrated Solution for Hospitality ProjectsAn ISO 9001:2000 Certified Company

CB. K. Eqpt /Specs GOLDEN TEMPLE - AMRITSAR Page- 17of 81INDIA Sector -17, Dwarka, New Delhi -110078

www.hpgconsulting.com

ITEM NO : R-05 HAND WASH SINK UNIT

QUANTITY: 3 Tentative Image

CUSTOM BUILT

SIZE

Width:

500 mm

Depth:

500 mm

Height:

512 mm

CAPACITY

M.E.P REQUIREMENT SPECIFICATIONS

PLUMBING : For construction detail refer standard shop drawing no. :-HPG/FD/05.

Top consist of no. 16 GA S.S. sheet.

150 mm high rear splash.

Front both side turned up 12mm & 45 deg turneddown40mm & in 12mm.

Rear turned up 150mm, returned 25mm & down 12mm.

420mm dia x 200mm deep no. 16 GA S.S. sink. 38mm diaC.P. waste.

One (1) no. deck mounted water mixer faucet.

No. 16 GA S.S. wall brackets secured to top w/ anchorS.S.nuts & bolts.

Front & both sides # 20 GA S.S. apron.

Cold ∅ ½”

Hot ∅ ½”

Waste ∅ 1 ½”

ELECTRIC :

Power NA

Voltage NA

EXHAUST

NA

GAS:

BTU NA

Con. ∅ NA mm

ACCESSORIES: Soap dispenser, Paper dispenser, Cap Stand

SPECIAL NOTE: All Sheet /Pipe S.S. 304 Grade Pre-polished Plastic Coated.

Page 18: AMRITSAR SPECIFICATIONS FOR CUSTOM BUILT KITCHEN …sgpc.net/wp-content/uploads/2013/07/CUSTOM-BUILT... · INDIA Sector -17, Dwarka, New Delhi -110078 GENERAL SPECIFICATIONS FOR CUSTOM

Integrated Solution for Hospitality ProjectsAn ISO 9001:2000 Certified Company

CB. K. Eqpt /Specs GOLDEN TEMPLE - AMRITSAR Page- 18of 81INDIA Sector -17, Dwarka, New Delhi -110078

www.hpgconsulting.com

ITEM NO : R-06 MOBILE PLATFORM TROLLEY

QUANTITY: 11

CUSTOM BUILT

SIZE

Width:

900 mm

Depth:

600 mm

Height:

900 mm

CAPACITY

M.E.P REQUIREMENT SPECIFICATIONS

PLUMBING : For construction detail refer standard shop drawing no. :-HPG/FD/06.

# 14 Ga. S.S. top channel shape.

Top and body secured to 38mm x 38mm x 3mm thick S.S.welded angle frame work.

38mm dia S.S. pipe handle with pipe reinforcement.

150mm high 12mm Dia S.S. pipe railing rear & both sides.

(4) no. heavy duty 125mm dia Non marking rubberizedcastors all with brakes.

Cold ∅ NA

Hot ∅ NA

Waste ∅ NA

ELECTRIC :

Power NA

Voltage NA

EXHAUST

NA

GAS:

BTU NA

Con. ∅ NA

ACCESSORIES:

SPECIAL NOTE: All Sheet /Pipe S.S. 304 Grade Pre-polished Plastic Coated.

Page 19: AMRITSAR SPECIFICATIONS FOR CUSTOM BUILT KITCHEN …sgpc.net/wp-content/uploads/2013/07/CUSTOM-BUILT... · INDIA Sector -17, Dwarka, New Delhi -110078 GENERAL SPECIFICATIONS FOR CUSTOM

Integrated Solution for Hospitality ProjectsAn ISO 9001:2000 Certified Company

CB. K. Eqpt /Specs GOLDEN TEMPLE - AMRITSAR Page- 19of 81INDIA Sector -17, Dwarka, New Delhi -110078

www.hpgconsulting.com

ITEM NO : R-07 DRINKING WATER SINK

QUANTITY: 4

CUSTOM BUILT

SIZE

Width:

500 mm

Depth:

500 mm

Height:

250

CAPACITY

M.E.P REQUIREMENT SPECIFICATIONS

PLUMBING : 400mm x 400mm x 150mm deep # 16 Ga. S.S. sink, SinkComplete with 50mm dia lever handle operated waste outlet.

One (1) No. deck Mounted “Jaksons Make” Swivel type waterMixer faucet.

No. 14 Ga. S.S. wall Brackets. Secured to top with acorn Nuts& Bolts & Bracket secured to wall with anchor fasteners.

Front & both sides # 20 GA S.S. apron.

Cold ∅ ½”

Hot ∅ ½”

Waste ∅ 2” Dr-Waste

ELECTRIC :

Power NA

Voltage NA

EXHAUST

NA

GAS:

BTU NA

Con. ∅ NA mm

ACCESSORIES:

SPECIAL NOTE: All Sheet /Pipe S.S. 304 Grade Pre-polished PlasticCoated.

Page 20: AMRITSAR SPECIFICATIONS FOR CUSTOM BUILT KITCHEN …sgpc.net/wp-content/uploads/2013/07/CUSTOM-BUILT... · INDIA Sector -17, Dwarka, New Delhi -110078 GENERAL SPECIFICATIONS FOR CUSTOM

Integrated Solution for Hospitality ProjectsAn ISO 9001:2000 Certified Company

CB. K. Eqpt /Specs GOLDEN TEMPLE - AMRITSAR Page- 20of 81INDIA Sector -17, Dwarka, New Delhi -110078

www.hpgconsulting.com

ITEM NO : R-08 POTATO/ONION STORAGE BIN

QUANTITY: 13

CUSTOM BUILT

SIZE

Width:

1200 mm

Depth:

1200

Height:

900

CAPACITY

M.E.P REQUIREMENT SPECIFICATIONS

PLUMBING : For construction detail refer standard shop drawing no. :-HPG/FD/30.

25mm x 25mm #14 Ga. S.S. outer frame work.

Front, top rear & sides 6mm thick S.S. rod Cladding.

16 Ga. S.S base sloped rear to front

# 18 Ga. S.S. front/ top Hinged doors w/Rod Handle

Cold ∅ NA

Hot ∅ NA

Waste ∅ NA

ELECTRIC :

Power NA

Voltage NA

EXHAUST

NA

GAS:

BTU NA

Con. ∅ NA mm

ACCESSORIES:

SPECIAL NOTE: All Sheet /Pipe S.S. 304 Grade Pre-polished PlasticCoated.

Page 21: AMRITSAR SPECIFICATIONS FOR CUSTOM BUILT KITCHEN …sgpc.net/wp-content/uploads/2013/07/CUSTOM-BUILT... · INDIA Sector -17, Dwarka, New Delhi -110078 GENERAL SPECIFICATIONS FOR CUSTOM

Integrated Solution for Hospitality ProjectsAn ISO 9001:2000 Certified Company

CB. K. Eqpt /Specs GOLDEN TEMPLE - AMRITSAR Page- 21of 81INDIA Sector -17, Dwarka, New Delhi -110078

www.hpgconsulting.com

ITEM NO : R-09 FLUSHING HOSE UNIT

QUANTITY: 3

CUSTOM BUILT

SIZE

Length:

15 Mts.Hose reel.

Depth: Height:

CAPACITY

M.E.P REQUIREMENT SPECIFICATIONS

PLUMBING : Heavy duty Cast bronze Mixer Body, Suitable for mixing hot& cold water

S.S. stud bolts for grouting to wall at 1650 A.F.F.

15 MT. Dunlop Hose Reel with brass nozzle.

Heavy duty S.S. rod rack for winding hose when not use

Cold ∅ ¾”

Hot ∅ ¾”

Waste ∅ NA

ELECTRIC :

Power NA

Voltage NA

EXHAUST

NA

GAS:

BTU NA

Con. ∅ NA

ACCESSORIES:

SPECIAL NOTE: All Sheet /Pipe S.S. 304 Grade Pre-polished Plastic Coated.

Page 22: AMRITSAR SPECIFICATIONS FOR CUSTOM BUILT KITCHEN …sgpc.net/wp-content/uploads/2013/07/CUSTOM-BUILT... · INDIA Sector -17, Dwarka, New Delhi -110078 GENERAL SPECIFICATIONS FOR CUSTOM

Integrated Solution for Hospitality ProjectsAn ISO 9001:2000 Certified Company

CB. K. Eqpt /Specs GOLDEN TEMPLE - AMRITSAR Page- 22of 81INDIA Sector -17, Dwarka, New Delhi -110078

www.hpgconsulting.com

ITEM NO: R-16 GARBAGE CAN

QUANTITY: 2 Tentative Image

CUSTOM BUILT

SIZE

Width:

502 mm

Dia:

410 mm

Height:

673 mm

CAPACITY 70 liters

M.E.P REQUIREMENT SPECIFICATIONS

PLUMBING :

Steel Construction.

With rust, dent, chip or peel free.

Heavy duty Pedal Mechanism.

Tight fitting overlapping lid.

With Round Corner.

70 Liter Container Equipped with 2 full nylon Rear Wheelsfor better maneuverability.

Unit should be suitable for work in Food service area.

Cold ∅ NA mm

Hot ∅ NA mm

Waste ∅ NA mm

ELECTRIC :

Power NA

Voltage NA

Gas:

BTU NA

Con. ∅ mm

ACCESSORIES:

SPECIAL NOTE: Qty as per operator

Page 23: AMRITSAR SPECIFICATIONS FOR CUSTOM BUILT KITCHEN …sgpc.net/wp-content/uploads/2013/07/CUSTOM-BUILT... · INDIA Sector -17, Dwarka, New Delhi -110078 GENERAL SPECIFICATIONS FOR CUSTOM

Integrated Solution for Hospitality ProjectsAn ISO 9001:2000 Certified Company

CB. K. Eqpt /Specs GOLDEN TEMPLE - AMRITSAR Page- 23of 81INDIA Sector -17, Dwarka, New Delhi -110078

www.hpgconsulting.com

ITEM NO : FS-15 FLUSHING HOSE UNIT

QUANTITY: 2

CUSTOM BUILT

SIZE

Length:

15 Mts.Hose reel.

Depth: Height:

CAPACITY

M.E.P REQUIREMENT SPECIFICATIONS

PLUMBING : Heavy duty Cast bronze Mixer Body, Suitable for mixing hot& cold water

S.S. stud bolts for grouting to wall at 1650 A.F.F.

15 MT. Dunlop Hose Reel with brass nozzle.

Heavy duty S.S. rod rack for winding hose when not use

Cold ∅ ¾”

Hot ∅ ¾”

Waste ∅ NA

ELECTRIC :

Power NA

Voltage NA

EXHAUST

NA

GAS:

BTU NA

Con. ∅ NA

ACCESSORIES:

SPECIAL NOTE: All Sheet /Pipe S.S. 304 Grade Pre-polished Plastic Coated.

Page 24: AMRITSAR SPECIFICATIONS FOR CUSTOM BUILT KITCHEN …sgpc.net/wp-content/uploads/2013/07/CUSTOM-BUILT... · INDIA Sector -17, Dwarka, New Delhi -110078 GENERAL SPECIFICATIONS FOR CUSTOM

Integrated Solution for Hospitality ProjectsAn ISO 9001:2000 Certified Company

CB. K. Eqpt /Specs GOLDEN TEMPLE - AMRITSAR Page- 24of 81INDIA Sector -17, Dwarka, New Delhi -110078

www.hpgconsulting.com

ITEM NO: K-01 SINGLE BURNER STOCK POT RANGE

QUANTITY: 8 Tentative Image

CUSTOM BUILT

SIZE

Width:

1200 mm

Depth:

1200 mm

Height:

400mm

CAPACITY

M.E.P REQUIREMENT SPECIFICATIONS

PLUMBING : For construction detail refer standard shop drawing no. :-HPG/FD/47-B.

#14Ga. S.S. Top.

Top secured to 50mm x 50mm x 6mm thick S.S. weldedangle frame work.

Exterior # 18 Ga. S.S. cladding.

25mm x 25mm S.S. square pipe cross bracing at all sides.

One (1) no. 600mm x 600mm Cast iron grate (Removable).

One (1) no. M-50 H.P. burner with pilot lamp.

One (1) no. # 18 Ga. S.S. drip tray with Integral handle.

Built in pressure Controller regulator.

50mm x 50mm S.S. square pipe legs. With adjustable bulletfeet.

(4) Nos. Pot filler(Item No. K-01A) Wall Mounted“Jaksons Make and model is “JHT # 7102 DZ” 600mm longSwivel type Single Control water faucet.

Front and both sides # 20 G.A S.S Cladding, Rear open forservices.

Cold ∅ ½”

Hot ∅ NA

Waste ∅ NA

ELECTRIC :

Power NA

Voltage NA

EXHAUST

NA

GAS:

BTU 110000 E.A.

Con. ∅ ¾”

ACCESSORIES:

SPECIAL NOTE: All Sheet /Pipe S.S. 304 Grade Pre-polished Plastic Coated.

Page 25: AMRITSAR SPECIFICATIONS FOR CUSTOM BUILT KITCHEN …sgpc.net/wp-content/uploads/2013/07/CUSTOM-BUILT... · INDIA Sector -17, Dwarka, New Delhi -110078 GENERAL SPECIFICATIONS FOR CUSTOM

Integrated Solution for Hospitality ProjectsAn ISO 9001:2000 Certified Company

CB. K. Eqpt /Specs GOLDEN TEMPLE - AMRITSAR Page- 25of 81INDIA Sector -17, Dwarka, New Delhi -110078

www.hpgconsulting.com

ITEM NO: K-08 SPREADER TABLE

QUANTITY: 1

CUSTOM BUILT

SIZE

Width:

725 mm

Depth:

2000 mm

Height:

865 mm

CAPACITY

M.E.P REQUIREMENT SPECIFICATIONS

PLUMBING : For construction detail refer standard shop drawing no. :-HPG/FD/41-A.

#16Ga. S.S. Top.

Rear Side 150mm High Splash.

100mm setback Body/legs for Gas pipe routing.

Top secured to 38mm x 38mm x 3mm thick S.S. weldedangle frame work.

38mm x 38mm S.S. square pipe legs. With adjustable bulletfeet.

25mm x 25mm S.S. square pipe bottom & intermediateshelves..

Unit to match with adjoining cooking battery equipments insize, finish & construction.

Cold ∅ NA

Hot ∅ NA

Waste ∅ NA

ELECTRIC :

Power NA

Voltage NA

EXHAUST

NA

GAS:

BTU NA

Con. ∅ NA mm

ACCESSORIES:

SPECIAL NOTE: All Sheet /Pipe S.S. 304 Grade Pre-polished Plastic Coated.

Page 26: AMRITSAR SPECIFICATIONS FOR CUSTOM BUILT KITCHEN …sgpc.net/wp-content/uploads/2013/07/CUSTOM-BUILT... · INDIA Sector -17, Dwarka, New Delhi -110078 GENERAL SPECIFICATIONS FOR CUSTOM

Integrated Solution for Hospitality ProjectsAn ISO 9001:2000 Certified Company

CB. K. Eqpt /Specs GOLDEN TEMPLE - AMRITSAR Page- 26of 81INDIA Sector -17, Dwarka, New Delhi -110078

www.hpgconsulting.com

ITEM NO: K-09 SPREADER TABLE

QUANTITY: 13

CUSTOM BUILT

SIZE

Width:

900 mm

Depth:

2000 mm

Height:

865 mm

CAPACITY

M.E.P REQUIREMENT SPECIFICATIONS

PLUMBING : For construction detail refer standard shop drawing no. :-HPG/FD/41-A.

#16Ga. S.S. Top.

Rear Side 150mm High Splash.

100mm setback Body/legs for Gas pipe routing.

Top and body secured to 38mm x 38mm x 3mm thick S.S.welded angle frame work.

38mm x 38mm S.S. square pipe legs. With adjustable bulletfeet.

25mm x 25mm S.S. square pipe bottom & intermediateshelves.

Unit to match with adjoining cooking battery equipments insize, finish & construction.

Cold ∅ NA

Hot ∅ NA

Waste ∅ NA

ELECTRIC :

Power NA

Voltage NA

EXHAUST

NA

GAS:

BTU NA

Con. ∅ NA mm

ACCESSORIES:

SPECIAL NOTE: All Sheet /Pipe S.S. 304 Grade Pre-polished Plastic Coated.

Page 27: AMRITSAR SPECIFICATIONS FOR CUSTOM BUILT KITCHEN …sgpc.net/wp-content/uploads/2013/07/CUSTOM-BUILT... · INDIA Sector -17, Dwarka, New Delhi -110078 GENERAL SPECIFICATIONS FOR CUSTOM

Integrated Solution for Hospitality ProjectsAn ISO 9001:2000 Certified Company

CB. K. Eqpt /Specs GOLDEN TEMPLE - AMRITSAR Page- 27of 81INDIA Sector -17, Dwarka, New Delhi -110078

www.hpgconsulting.com

ITEM NO: K-12 S.S SERVICE CONSOLE

QUANTITY: 1

CUSTOM BUILT

SIZE

Width:

11850 mm.

Depth:

230 mm.

Height:

1200mm

CAPACITY

M.E.P REQUIREMENT SPECIFICATIONS

PLUMBING :

S.S 304 1.2 mm thick Construction.

Removable Panel.

Suitable to be mounted above floor.

Pre-piped for Gas, Water, Drainage, Electrical Servicesrequired as per cooking battery.

Cold ∅ NA

Hot ∅ NA

Waste ∅ NA

ELECTRIC :

Power NA

Voltage NA

Gas:

BTU NA

Con. ∅

ACCESSORIES:

SPECIAL NOTE: All Sheet /Pipe S.S. 304 Grade Pre-polished Plastic Coated.

Page 28: AMRITSAR SPECIFICATIONS FOR CUSTOM BUILT KITCHEN …sgpc.net/wp-content/uploads/2013/07/CUSTOM-BUILT... · INDIA Sector -17, Dwarka, New Delhi -110078 GENERAL SPECIFICATIONS FOR CUSTOM

Integrated Solution for Hospitality ProjectsAn ISO 9001:2000 Certified Company

CB. K. Eqpt /Specs GOLDEN TEMPLE - AMRITSAR Page- 28of 81INDIA Sector -17, Dwarka, New Delhi -110078

www.hpgconsulting.com

ITEM NO: K-15 S.S SERVICE CONSOLE

QUANTITY: 1

CUSTOM BUILT

SIZE

Width:

2820 mm. &

7750 mm

Depth:

230 mm.

Height:

1200mm

CAPACITY

M.E.P REQUIREMENT SPECIFICATIONS

PLUMBING :

S.S 304 1.2 mm thick Construction.

Removable Panel.

Suitable to be mounted above floor.

Pre-piped for Gas, Water, Drainage, Electrical Servicesrequired as per cooking battery.

Cold ∅ NA

Hot ∅ NA

Waste ∅ NA

ELECTRIC :

Power NA

Voltage NA

Gas:

BTU NA

Con. ∅

ACCESSORIES:

SPECIAL NOTE: All Sheet /Pipe S.S. 304 Grade Pre-polished Plastic Coated.

Page 29: AMRITSAR SPECIFICATIONS FOR CUSTOM BUILT KITCHEN …sgpc.net/wp-content/uploads/2013/07/CUSTOM-BUILT... · INDIA Sector -17, Dwarka, New Delhi -110078 GENERAL SPECIFICATIONS FOR CUSTOM

Integrated Solution for Hospitality ProjectsAn ISO 9001:2000 Certified Company

CB. K. Eqpt /Specs GOLDEN TEMPLE - AMRITSAR Page- 29of 81INDIA Sector -17, Dwarka, New Delhi -110078

www.hpgconsulting.com

ITEM NO : K-20 DRINKING WATER SINK

QUANTITY: 2

CUSTOM BUILT

SIZE

Width:

500 mm

Depth:

500 mm

Height:

250

CAPACITY

M.E.P REQUIREMENT SPECIFICATIONS

PLUMBING : 400mm x 400mm x 150mm deep # 16 Ga. S.S. sink, SinkComplete with 50mm dia lever handle operated waste outlet.

One (1) No. deck Mounted “Jaksons Make” Swivel type waterMixer faucet.

No. 14 Ga. S.S. wall Brackets. Secured to top with acorn Nuts& Bolts & Bracket secured to wall with anchor fasteners.

Front & both sides # 20 GA S.S. apron.

Cold ∅ ½”

Hot ∅ ½”

Waste ∅ 2” Dr-Waste

ELECTRIC :

Power NA

Voltage NA

EXHAUST

NA

GAS:

BTU NA

Con. ∅ NA mm

ACCESSORIES:

SPECIAL NOTE: All Sheet /Pipe S.S. 304 Grade Pre-polished Plastic Coated.

Page 30: AMRITSAR SPECIFICATIONS FOR CUSTOM BUILT KITCHEN …sgpc.net/wp-content/uploads/2013/07/CUSTOM-BUILT... · INDIA Sector -17, Dwarka, New Delhi -110078 GENERAL SPECIFICATIONS FOR CUSTOM

Integrated Solution for Hospitality ProjectsAn ISO 9001:2000 Certified Company

CB. K. Eqpt /Specs GOLDEN TEMPLE - AMRITSAR Page- 30of 81INDIA Sector -17, Dwarka, New Delhi -110078

www.hpgconsulting.com

ITEM NO : K-21 FLUSHING HOSE UNIT

QUANTITY: 9

CUSTOM BUILT

SIZE

Length:

15 Mts.Hose reel.

Depth: Height:

CAPACITY

M.E.P REQUIREMENT SPECIFICATIONS

PLUMBING : Heavy duty Cast bronze Mixer Body, Suitable for mixing hot& cold water

S.S. stud bolts for grouting to wall at 1650 A.F.F.

15 MT. Dunlop Hose Reel with brass nozzle.

Heavy duty S.S. rod rack for winding hose when not use

Cold ∅ ¾”

Hot ∅ ¾”

Waste ∅ NA

ELECTRIC :

Power NA

Voltage NA

EXHAUST

NA

GAS:

BTU NA

Con. ∅ NA

ACCESSORIES:

SPECIAL NOTE: All Sheet /Pipe S.S. 304 Grade Pre-polished Plastic Coated.

Page 31: AMRITSAR SPECIFICATIONS FOR CUSTOM BUILT KITCHEN …sgpc.net/wp-content/uploads/2013/07/CUSTOM-BUILT... · INDIA Sector -17, Dwarka, New Delhi -110078 GENERAL SPECIFICATIONS FOR CUSTOM

Integrated Solution for Hospitality ProjectsAn ISO 9001:2000 Certified Company

CB. K. Eqpt /Specs GOLDEN TEMPLE - AMRITSAR Page- 31of 81INDIA Sector -17, Dwarka, New Delhi -110078

www.hpgconsulting.com

ITEM NO: K-24 DAL WASHING MACHINE

QUANTITY: 4

CUSTOM BUILT

SIZE (APPROX.)

Width:

1800 mm

Depth:

1200 mm

Height:

1350 mm

CAPACITY 120-130 KG/Batch

M.E.P REQUIREMENT SPECIFICATIONS

PLUMBING : Fabricated using solid and superior quality of SS.

Both washing & soaking processes.

Dal washer to maintain hygiene of the machineries.

All contact parts are made of SS 304.

5 HP, 3 Phase with Italian geared Motor.

Cold ∅ 1-1/2” mm

Hot ∅ NA mm

Waste ∅ 2” mm

ELECTRIC :

Power 5 HP

Voltage 440.50.3 Ph

Gas:

BTU NA

Con. ∅ mm

ACCESSORIES:

SPECIAL NOTE:

Page 32: AMRITSAR SPECIFICATIONS FOR CUSTOM BUILT KITCHEN …sgpc.net/wp-content/uploads/2013/07/CUSTOM-BUILT... · INDIA Sector -17, Dwarka, New Delhi -110078 GENERAL SPECIFICATIONS FOR CUSTOM

Integrated Solution for Hospitality ProjectsAn ISO 9001:2000 Certified Company

CB. K. Eqpt /Specs GOLDEN TEMPLE - AMRITSAR Page- 32of 81INDIA Sector -17, Dwarka, New Delhi -110078

www.hpgconsulting.com

ITEM NO: K-25 GARBAGE CAN

QUANTITY: 6 Tentative Image

CUSTOM BUILT

SIZE

Width:

502 mm

Dia:

410 mm

Height:

673 mm

CAPACITY 70 liters

M.E.P REQUIREMENT SPECIFICATIONS

PLUMBING :

Steel Construction.

With rust, dent, chip or peel free.

Heavy duty Pedal Mechanism.

Tight fitting overlapping lid.

With Round Corner.

70 Liter Container Equipped with 2 full nylon Rear Wheelsfor better maneuverability.

Unit should be suitable for work in Food service area.

Cold ∅ NA mm

Hot ∅ NA mm

Waste ∅ NA mm

ELECTRIC :

Power NA

Voltage NA

Gas:

BTU NA

Con. ∅ mm

ACCESSORIES:

SPECIAL NOTE: Qty as per operator

Page 33: AMRITSAR SPECIFICATIONS FOR CUSTOM BUILT KITCHEN …sgpc.net/wp-content/uploads/2013/07/CUSTOM-BUILT... · INDIA Sector -17, Dwarka, New Delhi -110078 GENERAL SPECIFICATIONS FOR CUSTOM

Integrated Solution for Hospitality ProjectsAn ISO 9001:2000 Certified Company

CB. K. Eqpt /Specs GOLDEN TEMPLE - AMRITSAR Page- 33of 81INDIA Sector -17, Dwarka, New Delhi -110078

www.hpgconsulting.com

ITEM NO : K-28 HAND WASH SINK UNIT

QUANTITY: 6 Tentative Image

CUSTOM BUILT

SIZE

Width:

500 mm

Depth:

500 mm

Height:

512 mm

CAPACITY

M.E.P REQUIREMENT SPECIFICATIONS

PLUMBING : For construction detail refer standard shop drawing no. :-HPG/FD/05.

Top consist of no. 16 GA S.S. sheet.

150 mm high rear splash.

Front both side turned up 12mm & 45 deg turneddown40mm & in 12mm.

Rear turned up 150mm, returned 25mm & down 12mm.

420mm dia x 200mm deep no. 16 GA S.S. sink. 38mm diaC.P. waste.

One (1) no. deck mounted water mixer faucet.

No. 16 GA S.S. wall brackets secured to top w/ anchorS.S.nuts & bolts.

Front & both sides # 20 GA S.S. apron.

Cold ∅ ½”

Hot ∅ ½”

Waste ∅ 1 ½”

ELECTRIC :

Power NA

Voltage NA

EXHAUST

NA

GAS:

BTU NA

Con. ∅ NA mm

ACCESSORIES: Soap dispenser, Paper dispenser, Cap Stand

SPECIAL NOTE: All Sheet /Pipe S.S. 304 Grade Pre-polished Plastic Coated.

Page 34: AMRITSAR SPECIFICATIONS FOR CUSTOM BUILT KITCHEN …sgpc.net/wp-content/uploads/2013/07/CUSTOM-BUILT... · INDIA Sector -17, Dwarka, New Delhi -110078 GENERAL SPECIFICATIONS FOR CUSTOM

Integrated Solution for Hospitality ProjectsAn ISO 9001:2000 Certified Company

CB. K. Eqpt /Specs GOLDEN TEMPLE - AMRITSAR Page- 34of 81INDIA Sector -17, Dwarka, New Delhi -110078

www.hpgconsulting.com

ITEM NO : K-32 WORK TABLE

QUANTITY: 4 Tentative Image

CUSTOM BUILT

SIZE

Width:

1500 mm

Depth:

700 mm

Height:

850 mm

CAPACITY

M.E.P REQUIREMENT SPECIFICATIONS

PLUMBING : For construction detail refer standard shop drawing no. :-HPG/FD/23.

#16 Ga. S.S. Top.

150mm High Splash at Rear and/or against wall.

Front & both sides turned down 50 mm & in 12mm

Rear / wall side turned up 150 mm returned 25 mm & in12mm.

Top secured to 38mm x 38mm x 3mm thick S.S. weldedangle frame work.

Full length # 18 Ga. S.S. Bottom & intermediate shelves.

Four (4) no. 38mm Dia S.S. legs. With adjustable bulletfeet.

Cold ∅ NA

Hot ∅ NA

Waste ∅ NA

ELECTRIC :

Power NA

Voltage NA

EXHAUST

NA

GAS:

BTU NA

Con. ∅ NA mm

ACCESSORIES:

SPECIAL NOTE: All Sheet /Pipe S.S. 304 Grade Pre-polished PlasticCoated.

Page 35: AMRITSAR SPECIFICATIONS FOR CUSTOM BUILT KITCHEN …sgpc.net/wp-content/uploads/2013/07/CUSTOM-BUILT... · INDIA Sector -17, Dwarka, New Delhi -110078 GENERAL SPECIFICATIONS FOR CUSTOM

Integrated Solution for Hospitality ProjectsAn ISO 9001:2000 Certified Company

CB. K. Eqpt /Specs GOLDEN TEMPLE - AMRITSAR Page- 35of 81INDIA Sector -17, Dwarka, New Delhi -110078

www.hpgconsulting.com

ITEM NO : K-33 WORK TABLE

QUANTITY: 1 TENTATIVE IMAGE

CUSTOM BUILT

SIZE :

Width:

1100 mm(Verify)

Depth:

700 mm

Height:

850 mm

CAPACITY

M.E.P REQUIREMENT SPECIFICATIONS

PLUMBING : For construction detail refer standard shop drawing no. :-HPG/FD/25.

#16 Ga. S.S. Top.

150mm high Rear & both sides Splash.

Front & Right side turned down 50mm & in 12 mm, rear &Left side turned up 150 mm returned 25mm & in 12mm

Top secured to 38mm x 38mm x 3mm thick S.S. weldedangle frame work.

25mm Dia S.S. pipe cross bracing welded to legs at Rear &both sides. Front open for Garbage Bins.

Four (4)no. 38mm Dia S.S. legs. With adjustable bullet feet.

Cold ∅ NA

Hot ∅ NA

Waste ∅ NA

ELECTRIC :

Power NA

Voltage NA

EXHAUST

NA

GAS:

BTU NA

Con. ∅ NA mm

ACCESSORIES:

SPECIAL NOTE: All Sheet /Pipe S.S. 304 Grade Pre-polished Plastic Coated.

Page 36: AMRITSAR SPECIFICATIONS FOR CUSTOM BUILT KITCHEN …sgpc.net/wp-content/uploads/2013/07/CUSTOM-BUILT... · INDIA Sector -17, Dwarka, New Delhi -110078 GENERAL SPECIFICATIONS FOR CUSTOM

Integrated Solution for Hospitality ProjectsAn ISO 9001:2000 Certified Company

CB. K. Eqpt /Specs GOLDEN TEMPLE - AMRITSAR Page- 36of 81INDIA Sector -17, Dwarka, New Delhi -110078

www.hpgconsulting.com

ITEM NO : K-35 HOT BAIN MARIE COUNTER FOR FOODHOLDING

QUANTITY: 7 Tentative Image

CUSTOM BUILT

SIZE

Width:

1830 mm

Depth:

1220 mm

Height:

850mm

CAPACITY

M.E.P REQUIREMENT SPECIFICATIONS

PLUMBING : 2.0mm thick S.S. Top.

150mm high rear splash.

Top and body secured to 50mm x 50mm x 3mm thick S.S.welded angle frame work.

One no. approx 1525 mm x 1015mm x 550mm deep,2.0mm thick S.S. S.S. Bain Marie complete with water inletoutlet , heating element, 50 mm thick glass wool insulation.

Electrical panel complete with thermostat, on off switch &light indicator.

250mm high, Six (06) 50mm Dia S.S. legs. With adjustablebullet feet.

Low water automatic shut – off valve.

All sides 1.2mm thick S.S. cladding.

Two (02) no. 760mm x 1015mm x 450mm deep 1.2mmthick SS Pan with heat resistant handle and lid

Cold ∅ NA

Hot ∅ 1-1/2”

Waste ∅ 2” Wasteconnect tograting

ELECTRIC :

Power 6.0 K.W

Voltage 440-50-3

EXHAUST

NA

GAS:

BTU NA

Con. ∅ NA mm

ACCESSORIES:

SPECIAL NOTE: All Sheet /Pipe S.S. 304 Grade Pre-polished Plastic Coated.

Page 37: AMRITSAR SPECIFICATIONS FOR CUSTOM BUILT KITCHEN …sgpc.net/wp-content/uploads/2013/07/CUSTOM-BUILT... · INDIA Sector -17, Dwarka, New Delhi -110078 GENERAL SPECIFICATIONS FOR CUSTOM

Integrated Solution for Hospitality ProjectsAn ISO 9001:2000 Certified Company

CB. K. Eqpt /Specs GOLDEN TEMPLE - AMRITSAR Page- 37of 81INDIA Sector -17, Dwarka, New Delhi -110078

www.hpgconsulting.com

ITEM NO : K-36 MOBILE G.N PAN TROLLEY

QUANTITY: 4 TENTATIVE IMAGE

CUSTOM BUILT

SIZE

Width:

670 mm

Depth:

700 mm

Height:

1675 mm

CAPACITY

M.E.P REQUIREMENT SPECIFICATIONS

PLUMBING : For construction detail refer standard shop drawing no. :-HPG/FD/20.

Unit shall be Constructed As per GN 2/1 Pan.

40mm x 40mm x 16 Ga. S.S. square pipe welded construction.

# 18 Ga. S.S. base channel shape.

32mm x 32mm S.S. angle for Tray supporting welded to Outersquare pipe frame, Approx 16 pairs, 75mm c/c.

Four (4) no. 150mm Dia Non marking rubberized castors twowith brakes.

Rubber corner Bumper On all four sides.

25mm dia S.S. for Tray stopper at Rear.

Cold ∅ NA

Hot ∅ NA

Waste ∅ NA

ELECTRIC :

Power NA

Voltage NA

EXHAUST

NA

GAS:

BTU NA

Con. ∅ NA mm

ACCESSORIES:

SPECIAL NOTE: All Sheet /Pipe S.S. 304 Grade Pre-polished Plastic Coated.

Page 38: AMRITSAR SPECIFICATIONS FOR CUSTOM BUILT KITCHEN …sgpc.net/wp-content/uploads/2013/07/CUSTOM-BUILT... · INDIA Sector -17, Dwarka, New Delhi -110078 GENERAL SPECIFICATIONS FOR CUSTOM

Integrated Solution for Hospitality ProjectsAn ISO 9001:2000 Certified Company

CB. K. Eqpt /Specs GOLDEN TEMPLE - AMRITSAR Page- 38of 81INDIA Sector -17, Dwarka, New Delhi -110078

www.hpgconsulting.com

ITEM NO: K-42 MOBILE POT RACK

QUANTITY: 9 Tentative Image

CUSTOM BUILT

SIZE

Width:

1200 mm

Depth:

750 mm

Height:

1900 mm

CAPACITY

M.E.P REQUIREMENT SPECIFICATIONS

PLUMBING : For construction detail refer standard shop drawing no. :-HPG/FD/27.

Four (4) no. S.S. pipe shelves.

First shelf 300 A.F.F., Second 900 A.F.F. Third shelf 1375mmA.F.F. & Fourth shelf at 1850mm A.F.F.

Shelf outer tube 32mm dia S.S. pipe with 25mm dia S.S pipewelded to outer tube at 75 c/c.

Four (4) no. 38mm dia S.S. pipe upright on castor.

Four (4) no. 150mm dia Non marking rubberized castors twowith brakes.

Cold ∅ NA

Hot ∅ NA

Waste ∅ NA

ELECTRIC :

Power NA

Voltage NA

EXHAUST

NA

GAS:

BTU NA

Con. ∅ NA mm

ACCESSORIES:

SPECIAL NOTE: All Sheet /Pipe S.S. 304 Grade Pre-polished Plastic Coated.

Page 39: AMRITSAR SPECIFICATIONS FOR CUSTOM BUILT KITCHEN …sgpc.net/wp-content/uploads/2013/07/CUSTOM-BUILT... · INDIA Sector -17, Dwarka, New Delhi -110078 GENERAL SPECIFICATIONS FOR CUSTOM

Integrated Solution for Hospitality ProjectsAn ISO 9001:2000 Certified Company

CB. K. Eqpt /Specs GOLDEN TEMPLE - AMRITSAR Page- 39of 81INDIA Sector -17, Dwarka, New Delhi -110078

www.hpgconsulting.com

ITEM NO: K-44 MOBILE POT RACK

QUANTITY: 7 Tentative Image

CUSTOM BUILT

SIZE

Width:

1200 mm

Depth:

750 mm

Height:

1900 mm

CAPACITY

M.E.P REQUIREMENT SPECIFICATIONS

PLUMBING : For construction detail refer standard shop drawing no. :-HPG/FD/27.

Four (4) no. S.S. pipe shelves.

First shelf 300 A.F.F., Second 900 A.F.F. Third shelf 1375mmA.F.F. & Fourth shelf at 1850mm A.F.F.

Shelf outer tube 32mm dia S.S. pipe with 25mm dia S.S pipewelded to outer tube at 75 c/c.

Four (4) no. 38mm dia S.S. pipe upright on castor.

Four (4) no. 150mm dia Non marking rubberized castors twowith brakes.

Cold ∅ NA

Hot ∅ NA

Waste ∅ NA

ELECTRIC :

Power NA

Voltage NA

EXHAUST

NA

GAS:

BTU NA

Con. ∅ NA mm

ACCESSORIES:

SPECIAL NOTE: All Sheet /Pipe S.S. 304 Grade Pre-polished Plastic Coated.

Page 40: AMRITSAR SPECIFICATIONS FOR CUSTOM BUILT KITCHEN …sgpc.net/wp-content/uploads/2013/07/CUSTOM-BUILT... · INDIA Sector -17, Dwarka, New Delhi -110078 GENERAL SPECIFICATIONS FOR CUSTOM

Integrated Solution for Hospitality ProjectsAn ISO 9001:2000 Certified Company

CB. K. Eqpt /Specs GOLDEN TEMPLE - AMRITSAR Page- 40of 81INDIA Sector -17, Dwarka, New Delhi -110078

www.hpgconsulting.com

ITEM NO : K-49 DIRTY/CLEAN DISH TROLLEY

QUANTITY: 14 Tentative Image

CUSTOM BUILT

SIZE

Width:

1500 mm

Depth:

750 mm

Height:

850mm

CAPACITY

M.E.P REQUIREMENT SPECIFICATIONS

PLUMBING :

2.0 mm thick S.S. sheet base.

Base secured to 50mm x 50mm x 6 mm thick S.S. weldedangle frame work.

38mm x 38mm x 1.6mm square pipe outer frame welded tobase frame.

12mm wide x 3mm thick SS strip welded vertically &horizontally with gap approx. 100mm centre to centre andwelded to outer frame.

25mm Dia S.S. pipe handle both sides.

Four (4) Nos. of Castors 150 mm dia x 50 mm thick heavy-duty Nylo cast swivel type, two with brakes, fixed to achannel framework.

Corner bumper all sides.

Cold ∅ NA

Hot ∅ NA

Waste ∅ NA

ELECTRIC :

Power NA

Voltage NA

EXHAUST

NA

GAS:

BTU NA

Con. ∅ NA

ACCESSORIES:

SPECIAL NOTE: All Sheet /Pipe S.S. 304 Grade Pre-polished PlasticCoated.

Page 41: AMRITSAR SPECIFICATIONS FOR CUSTOM BUILT KITCHEN …sgpc.net/wp-content/uploads/2013/07/CUSTOM-BUILT... · INDIA Sector -17, Dwarka, New Delhi -110078 GENERAL SPECIFICATIONS FOR CUSTOM

Integrated Solution for Hospitality ProjectsAn ISO 9001:2000 Certified Company

CB. K. Eqpt /Specs GOLDEN TEMPLE - AMRITSAR Page- 41of 81INDIA Sector -17, Dwarka, New Delhi -110078

www.hpgconsulting.com

ITEM NO: K-54 GARBAGE CAN

QUANTITY: 5 Tentative Image

CUSTOM BUILT

SIZE

Width:

502 mm

Dia:

410 mm

Height:

673 mm

CAPACITY 70 liters

M.E.P REQUIREMENT SPECIFICATIONS

PLUMBING :

Steel Construction.

With rust, dent, chip or peel free.

Heavy duty Pedal Mechanism.

Tight fitting overlapping lid.

With Round Corner.

70 Liter Container Equipped with 2 full nylon Rear Wheelsfor better maneuverability.

Unit should be suitable for work in Food service area.

Cold ∅ NA mm

Hot ∅ NA mm

Waste ∅ NA mm

ELECTRIC :

Power NA

Voltage NA

Gas:

BTU NA

Con. ∅ mm

ACCESSORIES:

SPECIAL NOTE: Qty as per operator

Page 42: AMRITSAR SPECIFICATIONS FOR CUSTOM BUILT KITCHEN …sgpc.net/wp-content/uploads/2013/07/CUSTOM-BUILT... · INDIA Sector -17, Dwarka, New Delhi -110078 GENERAL SPECIFICATIONS FOR CUSTOM

Integrated Solution for Hospitality ProjectsAn ISO 9001:2000 Certified Company

CB. K. Eqpt /Specs GOLDEN TEMPLE - AMRITSAR Page- 42of 81INDIA Sector -17, Dwarka, New Delhi -110078

www.hpgconsulting.com

ITEM NO : K-59 FLUSHING HOSE UNIT

QUANTITY: 1

CUSTOM BUILT

SIZE

Length:

15 Mts.Hose reel.

Depth: Height:

CAPACITY

M.E.P REQUIREMENT SPECIFICATIONS

PLUMBING : Heavy duty Cast bronze Mixer Body, Suitable for mixing hot& cold water

S.S. stud bolts for grouting to wall at 1650 A.F.F.

15 MT. Dunlop Hose Reel with brass nozzle.

Heavy duty S.S. rod rack for winding hose when not use

Cold ∅ ¾”

Hot ∅ ¾”

Waste ∅ NA

ELECTRIC :

Power NA

Voltage NA

EXHAUST

NA

GAS:

BTU NA

Con. ∅ NA

ACCESSORIES:

SPECIAL NOTE: All Sheet /Pipe S.S. 304 Grade Pre-polished Plastic Coated.

Page 43: AMRITSAR SPECIFICATIONS FOR CUSTOM BUILT KITCHEN …sgpc.net/wp-content/uploads/2013/07/CUSTOM-BUILT... · INDIA Sector -17, Dwarka, New Delhi -110078 GENERAL SPECIFICATIONS FOR CUSTOM

Integrated Solution for Hospitality ProjectsAn ISO 9001:2000 Certified Company

CB. K. Eqpt /Specs GOLDEN TEMPLE - AMRITSAR Page- 43of 81INDIA Sector -17, Dwarka, New Delhi -110078

www.hpgconsulting.com

ITEM NO : K-62A DISH WASHING STATION - MANUAL

QUANTITY: 4 Tentative Image

CUSTOM BUILT

SIZE

Width:

20650 mm

Depth:

450 mm

Height:

865

CAPACITY

M.E.P REQUIREMENT SPECIFICATIONS

PLUMBING :

Unit constructed in parts Seven (7) equal parts.

50mm high splash at rear side.

Full length x 450 width x 350mm deep, Tank constructed of3mm thick S.S. sheet welded construction. Complete withtotal Twenty One (21) no. 50mm dia lever handle operatedwaste outlet with overflow system.

Tank top all sides bend 60mm down & 12mm in.

Tank secured to 50mm x 50mm x 3mm thick S.S. weldedangle frame work.

Forty two (42) , 50mm Dia S.S. legs with S.S. plate andgrouted to floor.

25mm Dia S.S. pipe cross bracing welded to legs at allsides.

Fourteen (14) nos. Deck Mounted “Jaksons Make” Swiveltype water Mixer faucet.

Cold ∅ (14) 1/2"

Hot ∅ NA

Waste ∅ (21)2"

ELECTRIC :

Power NA

Voltage NA

EXHAUST

NA

GAS:

BTU NA

Con. ∅ NA mm

ACCESSORIES:

SPECIAL NOTE: All Sheet /Pipe S.S. 304 Grade Pre-polished PlasticCoated.

Page 44: AMRITSAR SPECIFICATIONS FOR CUSTOM BUILT KITCHEN …sgpc.net/wp-content/uploads/2013/07/CUSTOM-BUILT... · INDIA Sector -17, Dwarka, New Delhi -110078 GENERAL SPECIFICATIONS FOR CUSTOM

Integrated Solution for Hospitality ProjectsAn ISO 9001:2000 Certified Company

CB. K. Eqpt /Specs GOLDEN TEMPLE - AMRITSAR Page- 44of 81INDIA Sector -17, Dwarka, New Delhi -110078

www.hpgconsulting.com

ITEM NO: K-63 WASTE REMOVAL TABLE

QUANTITY: 1

Tentative ImageCUSTOM BUILT

SIZE

Width:

5825, 3250mm (Verify)

Depth:

610 mm

Height:

900 mm(Verify)

CAPACITY

M.E.P REQUIREMENT SPECIFICATIONS

PLUMBING :

#14 Ga. S.S. Top.

All sides marine Edges.

150mm High splash against wall. Location as per plan.

Top secured 38mm x 38mm x 3mm Thick S.S. weldedangle frame work.

38mm Dia S.S. legs. With adjustable bullet feet.

25mm Dia S.S. pipe cross bracing welded to legs at allsides sides.

Cold ∅Hot ∅Waste ∅ELECTRIC :

Power

Voltage

Gas:

BTU NA

Con. ∅ NA mm

ACCESSORIES:

SPECIAL NOTE:

Page 45: AMRITSAR SPECIFICATIONS FOR CUSTOM BUILT KITCHEN …sgpc.net/wp-content/uploads/2013/07/CUSTOM-BUILT... · INDIA Sector -17, Dwarka, New Delhi -110078 GENERAL SPECIFICATIONS FOR CUSTOM

Integrated Solution for Hospitality ProjectsAn ISO 9001:2000 Certified Company

CB. K. Eqpt /Specs GOLDEN TEMPLE - AMRITSAR Page- 45of 81INDIA Sector -17, Dwarka, New Delhi -110078

www.hpgconsulting.com

ITEM NO: SK-01 SINGLE BURNER STOCK POT RANGE

QUANTITY: 6 Tentative Image

CUSTOM BUILT

SIZE

Width:

1200 mm

Depth:

1200 mm

Height:

400mm

CAPACITY

M.E.P REQUIREMENT SPECIFICATIONS

PLUMBING : For construction detail refer standard shop drawing no. :-HPG/FD/47-B.

#14Ga. S.S. Top.

Top secured to 50mm x 50mm x 6mm thick S.S. weldedangle frame work.

Exterior # 18 Ga. S.S. cladding.

25mm x 25mm S.S. square pipe cross bracing at all sides.

One (1) no. 600mm x 600mm Cast iron grate (Removable).

One (1) no. M-50 H.P. burner with pilot lamp.

One (1) no. # 18 Ga. S.S. drip tray with Integral handle.

Built in pressure Controller regulator.

50mm x 50mm S.S. square pipe legs. With adjustable bulletfeet.

(3) Nos. Pot filler (Item No. SK-01A) Wall Mounted“Jaksons Make and model is “JHT # 7102 DZ” 600mm longSwivel type Single Control water faucet.

Front and both sides # 20 G.A S.S Cladding, Rear open forservices.

Cold ∅ ½”(Purified)

Hot ∅ NA

Waste ∅ NA

ELECTRIC :

Power NA

Voltage NA

EXHAUST

NA

GAS:

BTU 110000 E.A.

Con. ∅ ¾”

ACCESSORIES:

SPECIAL NOTE: All Sheet /Pipe S.S. 304 Grade Pre-polished Plastic Coated.

Page 46: AMRITSAR SPECIFICATIONS FOR CUSTOM BUILT KITCHEN …sgpc.net/wp-content/uploads/2013/07/CUSTOM-BUILT... · INDIA Sector -17, Dwarka, New Delhi -110078 GENERAL SPECIFICATIONS FOR CUSTOM

Integrated Solution for Hospitality ProjectsAn ISO 9001:2000 Certified Company

CB. K. Eqpt /Specs GOLDEN TEMPLE - AMRITSAR Page- 46of 81INDIA Sector -17, Dwarka, New Delhi -110078

www.hpgconsulting.com

ITEM NO : SK-05 MOBILE WORK TABLE

QUANTITY: 2 Tentative Image

CUSTOM BUILT

SIZE

Width:

1500 mm

Depth:

700 mm

Height:

865

CAPACITY

M.E.P REQUIREMENT SPECIFICATIONS

PLUMBING : For construction detail refer standard shop drawing no. : -HPG/FD/26.

#16 Ga. S.S. Top with marine edges.

Top secured to 38mm x 38mm x 3mm thick S.S. weldedangle frame work.

Full width # 18 GA. S.S. Bottom shelf.

38mm Dia pipe legs. On castor.

Four (4) no. 125mm Dia Non marking rubberized castors two(2) with brakes.

Cold ∅ NA

Hot ∅ NA

Waste ∅ NA

ELECTRIC :

Power NA

Voltage NA

EXHAUST

NA

GAS:

BTU NA

Con. ∅ NA mm

ACCESSORIES:

SPECIAL NOTE: All Sheet /Pipe S.S. 304 Grade Pre-polished Plastic Coated.

Page 47: AMRITSAR SPECIFICATIONS FOR CUSTOM BUILT KITCHEN …sgpc.net/wp-content/uploads/2013/07/CUSTOM-BUILT... · INDIA Sector -17, Dwarka, New Delhi -110078 GENERAL SPECIFICATIONS FOR CUSTOM

Integrated Solution for Hospitality ProjectsAn ISO 9001:2000 Certified Company

CB. K. Eqpt /Specs GOLDEN TEMPLE - AMRITSAR Page- 47of 81INDIA Sector -17, Dwarka, New Delhi -110078

www.hpgconsulting.com

ITEM NO : SK-08 HAND WASH SINK UNIT

QUANTITY: 1 Tentative Image

CUSTOM BUILT

SIZE

Width:

500 mm

Depth:

500 mm

Height:

512 mm

CAPACITY

M.E.P REQUIREMENT SPECIFICATIONS

PLUMBING : For construction detail refer standard shop drawing no. :-HPG/FD/05.

Top consist of no. 16 GA S.S. sheet.

150 mm high rear splash.

Front both side turned up 12mm & 45 deg turneddown40mm & in 12mm.

Rear turned up 150mm, returned 25mm & down 12mm.

420mm dia x 200mm deep no. 16 GA S.S. sink. 38mm diaC.P. waste.

One (1) no. deck mounted water mixer faucet.

No. 16 GA S.S. wall brackets secured to top w/ anchorS.S.nuts & bolts.

Front & both sides # 20 GA S.S. apron.

Cold ∅ ½”

Hot ∅ ½”

Waste ∅ 1 ½”

ELECTRIC :

Power NA

Voltage NA

EXHAUST

NA

GAS:

BTU NA

Con. ∅ NA mm

ACCESSORIES: Soap dispenser, Paper dispenser, Cap Stand

SPECIAL NOTE: All Sheet /Pipe S.S. 304 Grade Pre-polished Plastic Coated.

Page 48: AMRITSAR SPECIFICATIONS FOR CUSTOM BUILT KITCHEN …sgpc.net/wp-content/uploads/2013/07/CUSTOM-BUILT... · INDIA Sector -17, Dwarka, New Delhi -110078 GENERAL SPECIFICATIONS FOR CUSTOM

Integrated Solution for Hospitality ProjectsAn ISO 9001:2000 Certified Company

CB. K. Eqpt /Specs GOLDEN TEMPLE - AMRITSAR Page- 48of 81INDIA Sector -17, Dwarka, New Delhi -110078

www.hpgconsulting.com

ITEM NO : SK-09 FLUSHING HOSE UNIT

QUANTITY: 1

CUSTOM BUILT

SIZE

Length:

15 Mts.Hose reel.

Depth: Height:

CAPACITY

M.E.P REQUIREMENT SPECIFICATIONS

PLUMBING : Heavy duty Cast bronze Mixer Body, Suitable for mixing hot& cold water

S.S. stud bolts for grouting to wall at 1650 A.F.F.

15 MT. Dunlop Hose Reel with brass nozzle.

Heavy duty S.S. rod rack for winding hose when not use

Cold ∅ ¾”

Hot ∅ ¾”

Waste ∅ NA

ELECTRIC :

Power NA

Voltage NA

EXHAUST

NA

GAS:

BTU NA

Con. ∅ NA

ACCESSORIES:

SPECIAL NOTE: All Sheet /Pipe S.S. 304 Grade Pre-polished Plastic Coated.

Page 49: AMRITSAR SPECIFICATIONS FOR CUSTOM BUILT KITCHEN …sgpc.net/wp-content/uploads/2013/07/CUSTOM-BUILT... · INDIA Sector -17, Dwarka, New Delhi -110078 GENERAL SPECIFICATIONS FOR CUSTOM

Integrated Solution for Hospitality ProjectsAn ISO 9001:2000 Certified Company

CB. K. Eqpt /Specs GOLDEN TEMPLE - AMRITSAR Page- 49of 81INDIA Sector -17, Dwarka, New Delhi -110078

www.hpgconsulting.com

ITEM NO: SK-11 MOBILE POT RACK

QUANTITY: 5 Tentative Image

CUSTOM BUILT

SIZE

Width:

(4) 2000 mm

(1) 1500 mm

Depth:

900 mm

Height:

1900 mm

CAPACITY

M.E.P REQUIREMENT SPECIFICATIONS

PLUMBING : For construction detail refer standard shop drawing no. :-HPG/FD/27.

Four (4) no. S.S. pipe shelves.

First shelf 300 A.F.F., Second 900 A.F.F. Third shelf 1375mmA.F.F. & Fourth shelf at 1850mm A.F.F.

Shelf outer tube 32mm dia S.S. pipe with 25mm dia S.S pipewelded to outer tube at 75 c/c.

Four (4) no. 38mm dia S.S. pipe upright on castor.

Four (4) no. 150mm dia Non marking rubberized castors twowith brakes.

Cold ∅ NA

Hot ∅ NA

Waste ∅ NA

ELECTRIC :

Power NA

Voltage NA

EXHAUST

NA

GAS:

BTU NA

Con. ∅ NA mm

ACCESSORIES:

SPECIAL NOTE: All Sheet /Pipe S.S. 304 Grade Pre-polished Plastic Coated.

Page 50: AMRITSAR SPECIFICATIONS FOR CUSTOM BUILT KITCHEN …sgpc.net/wp-content/uploads/2013/07/CUSTOM-BUILT... · INDIA Sector -17, Dwarka, New Delhi -110078 GENERAL SPECIFICATIONS FOR CUSTOM

Integrated Solution for Hospitality ProjectsAn ISO 9001:2000 Certified Company

CB. K. Eqpt /Specs GOLDEN TEMPLE - AMRITSAR Page- 50of 81INDIA Sector -17, Dwarka, New Delhi -110078

www.hpgconsulting.com

ITEM NO: SK-13 GARBAGE CAN

QUANTITY: 1 Tentative Image

CUSTOM BUILT

SIZE

Width:

502 mm

Dia:

410 mm

Height:

673 mm

CAPACITY 70 liters

M.E.P REQUIREMENT SPECIFICATIONS

PLUMBING :

Steel Construction.

With rust, dent, chip or peel free.

Heavy duty Pedal Mechanism.

Tight fitting overlapping lid.

With Round Corner.

70 Liter Container Equipped with 2 full nylon Rear Wheelsfor better maneuverability.

Unit should be suitable for work in Food service area.

Cold ∅ NA mm

Hot ∅ NA mm

Waste ∅ NA mm

ELECTRIC :

Power NA

Voltage NA

Gas:

BTU NA

Con. ∅ mm

ACCESSORIES:

SPECIAL NOTE: Qty as per operator

Page 51: AMRITSAR SPECIFICATIONS FOR CUSTOM BUILT KITCHEN …sgpc.net/wp-content/uploads/2013/07/CUSTOM-BUILT... · INDIA Sector -17, Dwarka, New Delhi -110078 GENERAL SPECIFICATIONS FOR CUSTOM

Integrated Solution for Hospitality ProjectsAn ISO 9001:2000 Certified Company

CB. K. Eqpt /Specs GOLDEN TEMPLE - AMRITSAR Page- 51of 81INDIA Sector -17, Dwarka, New Delhi -110078

www.hpgconsulting.com

ITEM NO : CK-01 RAW FOOD TRANSPORT TROLLEY

QUANTITY: 8 Tentative Image

CUSTOM BUILT

SIZE

Width:

1500 mm

Depth:

900 mm

Height:

1050 mm

CAPACITY

M.E.P REQUIREMENT SPECIFICATIONS

PLUMBING : For construction detail refer standard shop drawing no. : -HPG/FD/06.

200mm high pan, 2.0mm thick S.S. pan welded constructionwith top edges all turned out 25mm, down 25mm and in12mm.

Top and body secured to 50mm x 50mm x 2mm thick S.S.welded angle frame work.

38mm dia S.S. pipe handle with pipe reinforcement.

Four (4) no. heavy duty 150mm dia x 50mm thick Nonmarking rubberized castors all with brakes.

Five (5) nos. approx 600mm x 300mm x 300mm S.S. rodremovable basket with Handle.

Basket constructed of 8 mm dia S.S. outer frame with 3mmthick S.S. wire mesh base and sides.

Cold ∅ NA

Hot ∅ NA

Waste ∅ NA

ELECTRIC :

Power NA

Voltage NA

EXHAUST

NA

GAS:

BTU NA

Con. ∅ NA

ACCESSORIES:

SPECIAL NOTE: All Sheet /Pipe S.S. 304 Grade Pre-polished Plastic Coated.

Page 52: AMRITSAR SPECIFICATIONS FOR CUSTOM BUILT KITCHEN …sgpc.net/wp-content/uploads/2013/07/CUSTOM-BUILT... · INDIA Sector -17, Dwarka, New Delhi -110078 GENERAL SPECIFICATIONS FOR CUSTOM

Integrated Solution for Hospitality ProjectsAn ISO 9001:2000 Certified Company

CB. K. Eqpt /Specs GOLDEN TEMPLE - AMRITSAR Page- 52of 81INDIA Sector -17, Dwarka, New Delhi -110078

www.hpgconsulting.com

ITEM NO : CK-04 HAND WASH SINK UNIT

QUANTITY: 3 Tentative Image

CUSTOM BUILT

SIZE

Width:

500 mm

Depth:

500 mm

Height:

512 mm

CAPACITY

M.E.P REQUIREMENT SPECIFICATIONS

PLUMBING : For construction detail refer standard shop drawing no. : -HPG/FD/05.

Top consist of no. 16 GA S.S. sheet.

150 mm high rear splash.

Front both side turned up 12mm & 45 deg turneddown40mm & in 12mm.

Rear turned up 150mm, returned 25mm & down 12mm.

420mm dia x 200mm deep no. 16 GA S.S. sink. 38mm diaC.P. waste.

One (1) no. deck mounted water mixer faucet.

No. 16 GA S.S. wall brackets secured to top w/ anchorS.S.nuts & bolts.

Front & both sides # 20 GA S.S. apron.

Cold ∅ ½”

Hot ∅ ½”

Waste ∅ 1 ½”

ELECTRIC :

Power NA

Voltage NA

EXHAUST

NA

GAS:

BTU NA

Con. ∅ NA mm

ACCESSORIES: Soap dispenser, Paper dispenser, Cap Stand

SPECIAL NOTE: All Sheet /Pipe S.S. 304 Grade Pre-polished Plastic Coated.

Page 53: AMRITSAR SPECIFICATIONS FOR CUSTOM BUILT KITCHEN …sgpc.net/wp-content/uploads/2013/07/CUSTOM-BUILT... · INDIA Sector -17, Dwarka, New Delhi -110078 GENERAL SPECIFICATIONS FOR CUSTOM

Integrated Solution for Hospitality ProjectsAn ISO 9001:2000 Certified Company

CB. K. Eqpt /Specs GOLDEN TEMPLE - AMRITSAR Page- 53of 81INDIA Sector -17, Dwarka, New Delhi -110078

www.hpgconsulting.com

ITEM NO : CK-05 FOOD TRANSPORT TROLLEY

QUANTITY: 7 Tentative Image

CUSTOM BUILT

SIZE

Width:

900 mm

Depth:

750 mm

Height:

1050 mm

CAPACITY

M.E.P REQUIREMENT SPECIFICATIONS

PLUMBING : For construction detail refer standard shop drawing no. : -HPG/FD/06.

200mm high pan, 2.0mm thick S.S. pan welded constructionwith top edges all turned out 25mm, down 25mm and in12mm.

Top and body secured to 50mm x 50mm x 2mm thick S.S.welded angle frame work.

25mm dia S.S. pipe handle with pipe reinforcement.

Four (4) no. heavy duty 150mm dia x 50mm thick Nonmarking rubberized castors all with brakes.

Two (2) nos. approx 600mm x 300mm x 300mm S.S. rodremovable basket with Handle.

Basket constructed of 8 mm dia S.S. outer frame with 3mmthick S.S. wire mesh base and sides.

Cold ∅ NA

Hot ∅ NA

Waste ∅ NA

ELECTRIC :

Power NA

Voltage NA

EXHAUST

NA

GAS:

BTU NA

Con. ∅ NA

ACCESSORIES:

SPECIAL NOTE: All Sheet /Pipe S.S. 304 Grade Pre-polished Plastic Coated.

Page 54: AMRITSAR SPECIFICATIONS FOR CUSTOM BUILT KITCHEN …sgpc.net/wp-content/uploads/2013/07/CUSTOM-BUILT... · INDIA Sector -17, Dwarka, New Delhi -110078 GENERAL SPECIFICATIONS FOR CUSTOM

Integrated Solution for Hospitality ProjectsAn ISO 9001:2000 Certified Company

CB. K. Eqpt /Specs GOLDEN TEMPLE - AMRITSAR Page- 54of 81INDIA Sector -17, Dwarka, New Delhi -110078

www.hpgconsulting.com

ITEM NO : CK-15 FLUSHING HOSE UNIT

QUANTITY: 2

CUSTOM BUILT

SIZE

Length:

15 Mts.Hose reel.

Depth: Height:

CAPACITY

M.E.P REQUIREMENT SPECIFICATIONS

PLUMBING : Heavy duty Cast bronze Mixer Body, Suitable for mixing hot& cold water

S.S. stud bolts for grouting to wall at 1650 A.F.F.

15 MT. Dunlop Hose Reel with brass nozzle.

Heavy duty S.S. rod rack for winding hose when not use

Cold ∅ ¾”

Hot ∅ ¾”

Waste ∅ NA

ELECTRIC :

Power NA

Voltage NA

EXHAUST

NA

GAS:

BTU NA

Con. ∅ NA

ACCESSORIES:

SPECIAL NOTE: All Sheet /Pipe S.S. 304 Grade Pre-polished Plastic Coated.

Page 55: AMRITSAR SPECIFICATIONS FOR CUSTOM BUILT KITCHEN …sgpc.net/wp-content/uploads/2013/07/CUSTOM-BUILT... · INDIA Sector -17, Dwarka, New Delhi -110078 GENERAL SPECIFICATIONS FOR CUSTOM

Integrated Solution for Hospitality ProjectsAn ISO 9001:2000 Certified Company

CB. K. Eqpt /Specs GOLDEN TEMPLE - AMRITSAR Page- 55of 81INDIA Sector -17, Dwarka, New Delhi -110078

www.hpgconsulting.com

ITEM NO : CK-17 DRINKING WATER SINK

QUANTITY: 2

CUSTOM BUILT

SIZE

Width:

500 mm

Depth:

500 mm

Height:

250

CAPACITY

M.E.P REQUIREMENT SPECIFICATIONS

PLUMBING : 400mm x 400mm x 150mm deep # 16 Ga. S.S. sink, SinkComplete with 50mm dia lever handle operated waste outlet.

One (1) No. deck Mounted “Jaksons Make” Swivel type waterMixer faucet.

No. 14 Ga. S.S. wall Brackets. Secured to top with acorn Nuts& Bolts & Bracket secured to wall with anchor fasteners.

Front & both sides # 20 GA S.S. apron.

Cold ∅ ½”

Hot ∅ ½”

Waste ∅ 2” Dr-Waste

ELECTRIC :

Power NA

Voltage NA

EXHAUST

NA

GAS:

BTU NA

Con. ∅ NA mm

ACCESSORIES:

SPECIAL NOTE: All Sheet /Pipe S.S. 304 Grade Pre-polished PlasticCoated.

Page 56: AMRITSAR SPECIFICATIONS FOR CUSTOM BUILT KITCHEN …sgpc.net/wp-content/uploads/2013/07/CUSTOM-BUILT... · INDIA Sector -17, Dwarka, New Delhi -110078 GENERAL SPECIFICATIONS FOR CUSTOM

Integrated Solution for Hospitality ProjectsAn ISO 9001:2000 Certified Company

CB. K. Eqpt /Specs GOLDEN TEMPLE - AMRITSAR Page- 56of 81INDIA Sector -17, Dwarka, New Delhi -110078

www.hpgconsulting.com

ITEM NO : CK-18 MOBILE G.N PAN TROLLEY

QUANTITY: 3 TENTATIVE IMAGE

CUSTOM BUILT

SIZE

Width:

670 mm

Depth:

700 mm

Height:

1675 mm

CAPACITY

M.E.P REQUIREMENT SPECIFICATIONS

PLUMBING : For construction detail refer standard shop drawing no. :-HPG/FD/20.

Unit shall be Constructed As per GN 2/1 Pan.

40mm x 40mm x 16 Ga. S.S. square pipe welded construction.

# 18 Ga. S.S. base channel shape.

32mm x 32mm S.S. angle for Tray supporting welded to Outersquare pipe frame, Approx 16 pairs, 75mm c/c.

Four (4) no. 150mm Dia Non marking rubberized castors twowith brakes.

Rubber corner Bumper On all four sides.

25mm dia S.S. for Tray stopper at Rear.

Cold ∅ NA

Hot ∅ NA

Waste ∅ NA

ELECTRIC :

Power NA

Voltage NA

EXHAUST

NA

GAS:

BTU NA

Con. ∅ NA mm

ACCESSORIES:

SPECIAL NOTE: All Sheet /Pipe S.S. 304 Grade Pre-polished Plastic Coated.

Page 57: AMRITSAR SPECIFICATIONS FOR CUSTOM BUILT KITCHEN …sgpc.net/wp-content/uploads/2013/07/CUSTOM-BUILT... · INDIA Sector -17, Dwarka, New Delhi -110078 GENERAL SPECIFICATIONS FOR CUSTOM

Integrated Solution for Hospitality ProjectsAn ISO 9001:2000 Certified Company

CB. K. Eqpt /Specs GOLDEN TEMPLE - AMRITSAR Page- 57of 81INDIA Sector -17, Dwarka, New Delhi -110078

www.hpgconsulting.com

ITEM NO : CK-20 FOOD TRANSPORT TROLLEY

QUANTITY: 27 Tentative Image

CUSTOM BUILT

SIZE

Width:

1275 mm

Depth:

900 mm

Height:

1050 mm

CAPACITY

M.E.P REQUIREMENT SPECIFICATIONS

PLUMBING : For construction detail refer standard shop drawing no. : -HPG/FD/06.

200mm high pan, 2.0mm thick S.S. pan welded constructionwith top edges all turned out 25mm, down 25mm and in12mm.

Top and body secured to 50mm x 50mm x 2mm thick S.S.welded angle frame work.

38mm dia S.S. pipe handle with pipe reinforcement.

Four (4) no. heavy duty 150mm dia x 50mm thick Nonmarking rubberized castors all with brakes.

Four (4) nos. approx 600mm x 300mm x 300mm S.S. rodremovable basket with Handle.

Basket constructed of 8 mm dia S.S. outer frame with 3mmthick S.S. wire mesh base and sides.

Cold ∅ NA

Hot ∅ NA

Waste ∅ NA

ELECTRIC :

Power NA

Voltage NA

EXHAUST

NA

GAS:

BTU NA

Con. ∅ NA

ACCESSORIES:

SPECIAL NOTE: All Sheet /Pipe S.S. 304 Grade Pre-polished Plastic Coated.

Page 58: AMRITSAR SPECIFICATIONS FOR CUSTOM BUILT KITCHEN …sgpc.net/wp-content/uploads/2013/07/CUSTOM-BUILT... · INDIA Sector -17, Dwarka, New Delhi -110078 GENERAL SPECIFICATIONS FOR CUSTOM

Integrated Solution for Hospitality ProjectsAn ISO 9001:2000 Certified Company

CB. K. Eqpt /Specs GOLDEN TEMPLE - AMRITSAR Page- 58of 81INDIA Sector -17, Dwarka, New Delhi -110078

www.hpgconsulting.com

ITEM NO: CK-21 GARBAGE CAN

QUANTITY: 3

TENTATIVE IMAGE

CUSTOM BUILT

SIZE

Width:

502 mm

Dia:

410 mm

Height:

673 mm

CAPACITY 70 liters

M.E.P REQUIREMENT SPECIFICATIONS

PLUMBING :

Steel Construction.

With rust, dent, chip or peel free.

Heavy duty Pedal Mechanism.

Tight fitting overlapping lid.

With Round Corner.

70 Liter Container Equipped with 2 full nylon Rear Wheelsfor better maneuverability.

Unit should be suitable for work in Food service area.

Cold ∅ NA mm

Hot ∅ NA mm

Waste ∅ NA mm

ELECTRIC :

Power NA

Voltage NA

Gas:

BTU NA

Con. ∅ mm

ACCESSORIES:

SPECIAL NOTE: Qty as per operator

Page 59: AMRITSAR SPECIFICATIONS FOR CUSTOM BUILT KITCHEN …sgpc.net/wp-content/uploads/2013/07/CUSTOM-BUILT... · INDIA Sector -17, Dwarka, New Delhi -110078 GENERAL SPECIFICATIONS FOR CUSTOM

Integrated Solution for Hospitality ProjectsAn ISO 9001:2000 Certified Company

CB. K. Eqpt /Specs GOLDEN TEMPLE - AMRITSAR Page- 59of 81INDIA Sector -17, Dwarka, New Delhi -110078

www.hpgconsulting.com

ITEM NO : CK-22 HOT BAIN MARIE COUNTER FOR FOODHOLDING

QUANTITY: 7 Tentative Image

CUSTOM BUILT

SIZE

Width:

1830 mm

Depth:

1220 mm

Height:

850mm

CAPACITY

M.E.P REQUIREMENT SPECIFICATIONS

PLUMBING : 2.0mm thick S.S. Top.

150mm high rear splash.

Top and body secured to 50mm x 50mm x 3mm thick S.S.welded angle frame work.

One no. approx 1525 mm x 1015mm x 550mm deep,2.0mm thick S.S. S.S. Bain Marie complete with water inletoutlet , heating element, 50 mm thick glass wool insulation.

Electrical panel complete with thermostat, on off switch &light indicator.

250mm high, Six (06) 50mm Dia S.S. legs. With adjustablebullet feet.

Low water automatic shut – off valve.

All sides 1.2mm thick S.S. cladding.

Two (02) no. 760mm x 1015mm x 450mm deep 1.2mmthick SS Pan with heat resistant handle and lid

Cold ∅ NA

Hot ∅ ½”

Waste ∅ 2” Wasteconnect tograting

ELECTRIC :

Power 6.0 K.W

Voltage 440-50-3

EXHAUST

NA

GAS:

BTU NA

Con. ∅ NA mm

ACCESSORIES:

SPECIAL NOTE: All Sheet /Pipe S.S. 304 Grade Pre-polished Plastic Coated.

Page 60: AMRITSAR SPECIFICATIONS FOR CUSTOM BUILT KITCHEN …sgpc.net/wp-content/uploads/2013/07/CUSTOM-BUILT... · INDIA Sector -17, Dwarka, New Delhi -110078 GENERAL SPECIFICATIONS FOR CUSTOM

Integrated Solution for Hospitality ProjectsAn ISO 9001:2000 Certified Company

CB. K. Eqpt /Specs GOLDEN TEMPLE - AMRITSAR Page- 60of 81INDIA Sector -17, Dwarka, New Delhi -110078

www.hpgconsulting.com

ITEM NO: CM-03 WORK TABLE W/SINK

QUANTITY: 1 Tentative Image

CUSTOM BUILT

SIZE :

Width:

1200 mm

Depth:

700 mm

Height:

850 mm

CAPACITY

M.E.P REQUIREMENT SPECIFICATIONS

PLUMBING : For construction detail refer standard shop drawing no. :-HPG/FD/13.

#16 Ga. S.S. Top.

150mm High at Rear & Right Side Splash.

Front & left sides turned down 50 mm & in 12mm

Rear & right side turned up 150 mm returned 25 mm & in12mm.

Top secured to 38mm x 38mm x 3mm thick S.S. weldedangle frame work.

Left of unit One (1) no. 450mm x 450mm x 200mm deep #16 Ga. S.S. sink, Sink Complete with 50mm dia lever handleoperated waste outlet & rear connected overflow.

Four (4) no. 38mm Dia S.S. legs. With adjustable bulletfeet.

25mm Dia S.S. pipe cross bracing welded to legs at Rear &both sides. Front open for garbage can.

# 20 G.A S.S Apron front of Sink.

One (1) No. Deck Mounted “Jaksons Make” Swivel typewater Mixer faucet.

Cold ∅ ½”

Hot ∅ ½”

Waste ∅ 2”

ELECTRIC :

Power NA

Voltage NA

EXHAUST

NA

GAS:

BTU NA

Con. ∅ NA mm

ACCESSORIES:

SPECIAL NOTE: All Sheet /Pipe S.S. 304 Grade Pre-polished Plastic Coated.

Page 61: AMRITSAR SPECIFICATIONS FOR CUSTOM BUILT KITCHEN …sgpc.net/wp-content/uploads/2013/07/CUSTOM-BUILT... · INDIA Sector -17, Dwarka, New Delhi -110078 GENERAL SPECIFICATIONS FOR CUSTOM

Integrated Solution for Hospitality ProjectsAn ISO 9001:2000 Certified Company

CB. K. Eqpt /Specs GOLDEN TEMPLE - AMRITSAR Page- 61of 81INDIA Sector -17, Dwarka, New Delhi -110078

www.hpgconsulting.com

ITEM NO: CM-05 WORK TABLE W/SINK

QUANTITY: 1 TENTATIVE IMAGE

CUSTOM BUILT

SIZE :

Width:

2100 mm

Depth:

700 mm

Height:

850 mm

CAPACITY

M.E.P REQUIREMENT SPECIFICATIONS

PLUMBING : For construction detail refer standard shop drawing no. :-HPG/FD/13.

#16 Ga. S.S. Top.

150mm High at Rear Side Splash.

Front & both sides turned down 50 mm & in 12mm

Rear side turned up 150 mm returned 25 mm & in 12mm.

Top secured to 38mm x 38mm x 3mm thick S.S. weldedangle frame work.

Left of unit One (1) no. 450mm x 450mm x 200mm deep #16 Ga. S.S. sink, Sink Complete with 50mm dia lever handleoperated waste outlet & rear connected overflow.

Six (6) no. 38mm Dia S.S. legs. With adjustable bullet feet.

25mm Dia S.S. pipe cross bracing welded to legs at Rear &both sides. Front open for garbage can.

# 20 G.A S.S Apron front of Sink.

One (1) No. Deck Mounted “Jaksons Make” Swivel typewater Mixer faucet.

Cold ∅ ½”

Hot ∅ ½”

Waste ∅ 2”

ELECTRIC :

Power NA

Voltage NA

EXHAUST

NA

GAS:

BTU NA

Con. ∅ NA mm

ACCESSORIES:

SPECIAL NOTE: All Sheet /Pipe S.S. 304 Grade Pre-polished Plastic Coated.

Page 62: AMRITSAR SPECIFICATIONS FOR CUSTOM BUILT KITCHEN …sgpc.net/wp-content/uploads/2013/07/CUSTOM-BUILT... · INDIA Sector -17, Dwarka, New Delhi -110078 GENERAL SPECIFICATIONS FOR CUSTOM

Integrated Solution for Hospitality ProjectsAn ISO 9001:2000 Certified Company

CB. K. Eqpt /Specs GOLDEN TEMPLE - AMRITSAR Page- 62of 81INDIA Sector -17, Dwarka, New Delhi -110078

www.hpgconsulting.com

ITEM NO: CM-06 WORK TABLE W/SINK

QUANTITY: 1 TENTATIVE IMAGE

CUSTOM BUILT

SIZE :

Width:

1500 mm

Depth:

700 mm

Height:

850 mm

CAPACITY

M.E.P REQUIREMENT SPECIFICATIONS

PLUMBING : For construction detail refer standard shop drawing no. :-HPG/FD/13.

#16 Ga. S.S. Top.

150mm High at Rear & left Side Splash.

Front & right sides turned down 50 mm & in 12mm

Rear & left sides turned up 150 mm returned 25 mm & in12mm.

Top secured to 38mm x 38mm x 3mm thick S.S. weldedangle frame work.

Left of unit One (1) no. 450mm x 450mm x 200mm deep #16 Ga. S.S. sink, Sink Complete with 50mm dia lever handleoperated waste outlet & rear connected overflow.

Four (4) no. 38mm Dia S.S. legs. With adjustable bulletfeet.

25mm Dia S.S. pipe cross bracing welded to legs at Rear &both sides. Front open for garbage can.

# 20 G.A S.S Apron front of Sink.

One (1) No. Deck Mounted “Jaksons Make” Swivel typewater Mixer faucet.

Cold ∅ ½”

Hot ∅ ½”

Waste ∅ 2”

ELECTRIC :

Power NA

Voltage NA

EXHAUST

NA

GAS:

BTU NA

Con. ∅ NA mm

ACCESSORIES:

SPECIAL NOTE: All Sheet /Pipe S.S. 304 Grade Pre-polished Plastic Coated.

Page 63: AMRITSAR SPECIFICATIONS FOR CUSTOM BUILT KITCHEN …sgpc.net/wp-content/uploads/2013/07/CUSTOM-BUILT... · INDIA Sector -17, Dwarka, New Delhi -110078 GENERAL SPECIFICATIONS FOR CUSTOM

Integrated Solution for Hospitality ProjectsAn ISO 9001:2000 Certified Company

CB. K. Eqpt /Specs GOLDEN TEMPLE - AMRITSAR Page- 63of 81INDIA Sector -17, Dwarka, New Delhi -110078

www.hpgconsulting.com

ITEM NO : CM-07 WORK TABLE

QUANTITY: 1 TENTATIVE IMAGE

CUSTOM BUILT

SIZE

Width:

1025 mm(Verify)

Depth:

700 mm

Height:

850 mm

CAPACITY

M.E.P REQUIREMENT SPECIFICATIONS

PLUMBING : For construction detail refer standard shop drawing no. :-HPG/FD/23.

#16 Ga. S.S. Top.

150mm High Splash at Rear & right side.

Front & left sides turned down 50 mm & in 12mm

Rear & right side turned up 150 mm returned 25 mm & in12mm.

Top secured to 38mm x 38mm x 3mm thick S.S. weldedangle frame work.

Full length # 18 Ga. S.S. Bottom & intermediate shelves.

Four (4) no. 38mm Dia S.S. legs. With adjustable bulletfeet.

Cold ∅ NA

Hot ∅ NA

Waste ∅ NA

ELECTRIC :

Power NA

Voltage NA

EXHAUST

NA

GAS:

BTU NA

Con. ∅ NA mm

ACCESSORIES:

SPECIAL NOTE: All Sheet /Pipe S.S. 304 Grade Pre-polished PlasticCoated.

Page 64: AMRITSAR SPECIFICATIONS FOR CUSTOM BUILT KITCHEN …sgpc.net/wp-content/uploads/2013/07/CUSTOM-BUILT... · INDIA Sector -17, Dwarka, New Delhi -110078 GENERAL SPECIFICATIONS FOR CUSTOM

Integrated Solution for Hospitality ProjectsAn ISO 9001:2000 Certified Company

CB. K. Eqpt /Specs GOLDEN TEMPLE - AMRITSAR Page- 64of 81INDIA Sector -17, Dwarka, New Delhi -110078

www.hpgconsulting.com

ITEM NO : CM-08 WORK TABLE

QUANTITY: 1 TENTATIVE IMAGE

CUSTOM BUILT

SIZE

Width:

1500 mm

Depth:

700 mm

Height:

850 mm

CAPACITY

M.E.P REQUIREMENT SPECIFICATIONS

PLUMBING : For construction detail refer standard shop drawing no. :-HPG/FD/23.

#16 Ga. S.S. Top.

150mm High Splash at Rear & left side.

Front & right sides turned down 50 mm & in 12mm

Rear & left side turned up 150 mm returned 25 mm & in12mm.

Top secured to 38mm x 38mm x 3mm thick S.S. weldedangle frame work.

Full length # 18 Ga. S.S. Bottom & intermediate shelves.

Four (4) no. 38mm Dia S.S. legs. With adjustable bulletfeet.

Cold ∅ NA

Hot ∅ NA

Waste ∅ NA

ELECTRIC :

Power NA

Voltage NA

EXHAUST

NA

GAS:

BTU NA

Con. ∅ NA mm

ACCESSORIES:

SPECIAL NOTE: All Sheet /Pipe S.S. 304 Grade Pre-polished PlasticCoated.

Page 65: AMRITSAR SPECIFICATIONS FOR CUSTOM BUILT KITCHEN …sgpc.net/wp-content/uploads/2013/07/CUSTOM-BUILT... · INDIA Sector -17, Dwarka, New Delhi -110078 GENERAL SPECIFICATIONS FOR CUSTOM

Integrated Solution for Hospitality ProjectsAn ISO 9001:2000 Certified Company

CB. K. Eqpt /Specs GOLDEN TEMPLE - AMRITSAR Page- 65of 81INDIA Sector -17, Dwarka, New Delhi -110078

www.hpgconsulting.com

ITEM NO : CM-09 WORK TABLE

QUANTITY: 1 TENTATIVE IMAGE

CUSTOM BUILT

SIZE

Width:

1500 mm

Depth:

700 mm

Height:

850 mm

CAPACITY

M.E.P REQUIREMENT SPECIFICATIONS

PLUMBING : For construction detail refer standard shop drawing no. :-HPG/FD/23.

#16 Ga. S.S. Top.

150mm High Splash at Rear side.

Front & both sides turned down 50 mm & in 12mm

Rear side turned up 150 mm returned 25 mm & in 12mm.

Top secured to 38mm x 38mm x 3mm thick S.S. weldedangle frame work.

Full length # 18 Ga. S.S. Bottom & intermediate shelves.

Four (4) no. 38mm Dia S.S. legs. With adjustable bulletfeet.

Cold ∅ NA

Hot ∅ NA

Waste ∅ NA

ELECTRIC :

Power NA

Voltage NA

EXHAUST

NA

GAS:

BTU NA

Con. ∅ NA mm

ACCESSORIES:

SPECIAL NOTE: All Sheet /Pipe S.S. 304 Grade Pre-polished PlasticCoated.

Page 66: AMRITSAR SPECIFICATIONS FOR CUSTOM BUILT KITCHEN …sgpc.net/wp-content/uploads/2013/07/CUSTOM-BUILT... · INDIA Sector -17, Dwarka, New Delhi -110078 GENERAL SPECIFICATIONS FOR CUSTOM

Integrated Solution for Hospitality ProjectsAn ISO 9001:2000 Certified Company

CB. K. Eqpt /Specs GOLDEN TEMPLE - AMRITSAR Page- 66of 81INDIA Sector -17, Dwarka, New Delhi -110078

www.hpgconsulting.com

ITEM NO : CM-15 GRIDDLE PLATE

QUANTITY: 4

CUSTOM BUILT

SIZE

Width:

6600 mm

Depth:

1800 mm

Height:

600mm

CAPACITY

M.E.P REQUIREMENT SPECIFICATIONS

PLUMBING : For construction detail refer standard shop drawing no. : -HPG/FD/46.

Equipment built in eight (08) section, Each section size1650mm x 900mm x 600mm high.

Full width x full depth x 20mm thick M.S. plate with 25mm x25mm "V" edges at all sides.

Equipment body secured 50mm x 50mm x 3mm thick S.S.welded angle frame work.

Exterior 1.2mm thick S.S. cladding.

Each section two no. grease collecting drawer.

Each section Four (04) no. “V” type H.P. burner rated at70,000 btu's with pilot lamp.

Auto Ignition.

Flame failure device.

Each section Six (06) 38mm dia x 1.6mm thick S.S. tubularpipe legs with S.S. adjustable bullet feet.

Cold ∅ NA

Hot ∅ NA

Waste ∅ NA

ELECTRIC :

Power NA

Voltage NA

EXHAUST

NA

GAS:

BTU 280,000ea.section

Con. ∅ ¾”

ACCESSORIES:

SPECIAL NOTE: All Sheet /Pipe S.S. 304 Grade Pre-polished Plastic Coated.

Page 67: AMRITSAR SPECIFICATIONS FOR CUSTOM BUILT KITCHEN …sgpc.net/wp-content/uploads/2013/07/CUSTOM-BUILT... · INDIA Sector -17, Dwarka, New Delhi -110078 GENERAL SPECIFICATIONS FOR CUSTOM

Integrated Solution for Hospitality ProjectsAn ISO 9001:2000 Certified Company

CB. K. Eqpt /Specs GOLDEN TEMPLE - AMRITSAR Page- 67of 81INDIA Sector -17, Dwarka, New Delhi -110078

www.hpgconsulting.com

ITEM NO : CM-22 HAND WASH SINK UNIT

QUANTITY: 4 TENTATIVE IMAGE

CUSTOM BUILT

SIZE

Width:

500 mm

Depth:

500 mm

Height:

512 mm

CAPACITY

M.E.P REQUIREMENT SPECIFICATIONS

PLUMBING : For construction detail refer standard shop drawing no. : -HPG/FD/05.

Top consist of no. 16 GA S.S. sheet.

150 mm high rear splash.

Front both side turned up 12mm & 45 deg turneddown40mm & in 12mm.

Rear turned up 150mm, returned 25mm & down 12mm.

420mm dia x 200mm deep no. 16 GA S.S. sink. 38mm diaC.P. waste.

One (1) no. deck mounted water mixer faucet.

No. 16 GA S.S. wall brackets secured to top w/ anchorS.S.nuts & bolts.

Front & both sides # 20 GA S.S. apron.

Cold ∅ ½”

Hot ∅ ½”

Waste ∅ 1 ½”

ELECTRIC :

Power NA

Voltage NA

EXHAUST

NA

GAS:

BTU NA

Con. ∅ NA mm

ACCESSORIES: Soap dispenser, Paper dispenser, Cap Stand

SPECIAL NOTE: All Sheet /Pipe S.S. 304 Grade Pre-polished Plastic Coated.

Page 68: AMRITSAR SPECIFICATIONS FOR CUSTOM BUILT KITCHEN …sgpc.net/wp-content/uploads/2013/07/CUSTOM-BUILT... · INDIA Sector -17, Dwarka, New Delhi -110078 GENERAL SPECIFICATIONS FOR CUSTOM

Integrated Solution for Hospitality ProjectsAn ISO 9001:2000 Certified Company

CB. K. Eqpt /Specs GOLDEN TEMPLE - AMRITSAR Page- 68of 81INDIA Sector -17, Dwarka, New Delhi -110078

www.hpgconsulting.com

ITEM NO : CM-23 GRIDDLE PLATE

QUANTITY: 1

CUSTOM BUILT

SIZE

Width:

4200 mm

Depth:

900 mm

Height:

865mm

CAPACITY

M.E.P REQUIREMENT SPECIFICATIONS

PLUMBING : For construction detail refer standard shop drawing no. : -HPG/FD/46.

Equipment built in Three (03) section, Each section size1400mm x 900mm x 865mm high.

Full width x full depth x 20mm thick M.S. plate with 25mm x25mm "V" edges at all sides.

Equipment body secured 50mm x 50mm x 3mm thick S.S.welded angle frame work.

Exterior 1.2mm thick S.S. cladding.

Each section two no. grease collecting drawer.

Each section Four (04) no. “V” type H.P. burner rated at70,000 btu's with pilot lamp.

Auto Ignition.

Flame failure device.

Each section Six (06) 38mm dia x 1.6mm thick S.S. tubularpipe legs with S.S. adjustable bullet feet.

25mm x 25mm S.S. square pipe under shelf.

Cold ∅ NA

Hot ∅ NA

Waste ∅ NA

ELECTRIC :

Power NA

Voltage NA

EXHAUST

NA

GAS:

BTU 280,000ea.section

Con. ∅ ¾”

ACCESSORIES:

SPECIAL NOTE: All Sheet /Pipe S.S. 304 Grade Pre-polished Plastic Coated.

Page 69: AMRITSAR SPECIFICATIONS FOR CUSTOM BUILT KITCHEN …sgpc.net/wp-content/uploads/2013/07/CUSTOM-BUILT... · INDIA Sector -17, Dwarka, New Delhi -110078 GENERAL SPECIFICATIONS FOR CUSTOM

Integrated Solution for Hospitality ProjectsAn ISO 9001:2000 Certified Company

CB. K. Eqpt /Specs GOLDEN TEMPLE - AMRITSAR Page- 69of 81INDIA Sector -17, Dwarka, New Delhi -110078

www.hpgconsulting.com

ITEM NO : CM-25 GRIDDLE PLATE

QUANTITY: 1

CUSTOM BUILT

SIZE

Width:

4710 mm

Depth:

900 mm

Height:

865mm

CAPACITY

M.E.P REQUIREMENT SPECIFICATIONS

PLUMBING : For construction detail refer standard shop drawing no. : -HPG/FD/46.

Equipment built in Three (03) section, Each section size1570mm x 900mm x 865mm high.

Full width x full depth x 20mm thick M.S. plate with 25mm x25mm "V" edges at all sides.

Equipment body secured 50mm x 50mm x 3mm thick S.S.welded angle frame work.

Exterior 1.2mm thick S.S. cladding.

Each section two no. grease collecting drawer.

Each section Four (04) no. “V” type H.P. burner rated at70,000 btu's with pilot lamp.

Auto Ignition.

Flame failure device.

Each section Six (06) 38mm dia x 1.6mm thick S.S. tubularpipe legs with S.S. adjustable bullet feet.

25mm x 25mm S.S. square pipe under shelf.

Cold ∅ NA

Hot ∅ NA

Waste ∅ NA

ELECTRIC :

Power NA

Voltage NA

EXHAUST

NA

GAS:

BTU 280,000ea.section

Con. ∅ ¾”

ACCESSORIES:

SPECIAL NOTE: All Sheet /Pipe S.S. 304 Grade Pre-polished Plastic Coated.

Page 70: AMRITSAR SPECIFICATIONS FOR CUSTOM BUILT KITCHEN …sgpc.net/wp-content/uploads/2013/07/CUSTOM-BUILT... · INDIA Sector -17, Dwarka, New Delhi -110078 GENERAL SPECIFICATIONS FOR CUSTOM

Integrated Solution for Hospitality ProjectsAn ISO 9001:2000 Certified Company

CB. K. Eqpt /Specs GOLDEN TEMPLE - AMRITSAR Page- 70of 81INDIA Sector -17, Dwarka, New Delhi -110078

www.hpgconsulting.com

ITEM NO: CM-29 GARBAGE CAN

QUANTITY: 10 Tentative Image

CUSTOM BUILT

SIZE

Width:

502 mm

Dia:

410 mm

Height:

673 mm

CAPACITY 70 liters

M.E.P REQUIREMENT SPECIFICATIONS

PLUMBING :

Steel Construction.

With rust, dent, chip or peel free.

Heavy duty Pedal Mechanism.

Tight fitting overlapping lid.

With Round Corner.

70 Liter Container Equipped with 2 full nylon Rear Wheelsfor better maneuverability.

Unit should be suitable for work in Food service area.

Cold ∅ NA mm

Hot ∅ NA mm

Waste ∅ NA mm

ELECTRIC :

Power NA

Voltage NA

Gas:

BTU NA

Con. ∅ mm

ACCESSORIES:

SPECIAL NOTE: Qty as per operator

Page 71: AMRITSAR SPECIFICATIONS FOR CUSTOM BUILT KITCHEN …sgpc.net/wp-content/uploads/2013/07/CUSTOM-BUILT... · INDIA Sector -17, Dwarka, New Delhi -110078 GENERAL SPECIFICATIONS FOR CUSTOM

Integrated Solution for Hospitality ProjectsAn ISO 9001:2000 Certified Company

CB. K. Eqpt /Specs GOLDEN TEMPLE - AMRITSAR Page- 71of 81INDIA Sector -17, Dwarka, New Delhi -110078

www.hpgconsulting.com

ITEM NO: CM-30 S.S SERVICE CONSOLE

QUANTITY: 5

CUSTOM BUILT

SIZE

Width:

600 mm.

Depth:

200 mm.

Height:

2700mm (As perfalse ceiling)

CAPACITY

M.E.P REQUIREMENT SPECIFICATIONS

PLUMBING :

S.S 304 1.2 mm thick Construction.

Removable Panel.

Suitable to be mounted above floor.

Pre-piped for Gas and Electrical Services required as percooking battery.

Approx 450mm x 900mm S.S. shutter for servicesmaintenance/control

Location as per chapatti machine vendor.

Cold ∅ NA

Hot ∅ NA

Waste ∅ NA

ELECTRIC :

Power NA

Voltage NA

Gas:

BTU NA

Con. ∅

ACCESSORIES:

SPECIAL NOTE: All Sheet /Pipe S.S. 304 Grade Pre-polished Plastic Coated.

Page 72: AMRITSAR SPECIFICATIONS FOR CUSTOM BUILT KITCHEN …sgpc.net/wp-content/uploads/2013/07/CUSTOM-BUILT... · INDIA Sector -17, Dwarka, New Delhi -110078 GENERAL SPECIFICATIONS FOR CUSTOM

Integrated Solution for Hospitality ProjectsAn ISO 9001:2000 Certified Company

CB. K. Eqpt /Specs GOLDEN TEMPLE - AMRITSAR Page- 72of 81INDIA Sector -17, Dwarka, New Delhi -110078

www.hpgconsulting.com

ITEM NO : CM-38 DUNNAGE RACK

QUANTITY: 21

CUSTOM BUILT

SIZE

Width:

1200 mm

Depth:

610 mm

Height:

305

CAPACITY

M.E.P REQUIREMENT SPECIFICATIONS

PLUMBING : For construction detail refer standard shop drawing no. : -HPG/FD/12.

# 14 GA. 304 S.S Constructions.

all sides turned down 50mm and in 12mm.

16G. S.S. inverted channels mounted on S.S.

14 GA. Square pipe feet w/S.S. adjustable flanged typebolts.

Legs to be cross braced on all fours sides

Cold ∅ NA

Hot ∅ NA

Waste ∅ NA

ELECTRIC :

Power NA

Voltage NA

EXHAUST

NA

GAS:

BTU NA

Con. ∅ NA mm

ACCESSORIES:

SPECIAL NOTE: All Sheet /Pipe S.S. 304 Grade Pre-polished Plastic Coated.

Page 73: AMRITSAR SPECIFICATIONS FOR CUSTOM BUILT KITCHEN …sgpc.net/wp-content/uploads/2013/07/CUSTOM-BUILT... · INDIA Sector -17, Dwarka, New Delhi -110078 GENERAL SPECIFICATIONS FOR CUSTOM

Integrated Solution for Hospitality ProjectsAn ISO 9001:2000 Certified Company

CB. K. Eqpt /Specs GOLDEN TEMPLE - AMRITSAR Page- 73of 81INDIA Sector -17, Dwarka, New Delhi -110078

www.hpgconsulting.com

ITEM NO : CM-41 DRINKING WATER SINK

QUANTITY: 5

CUSTOM BUILT

SIZE

Width:

500 mm

Depth:

500 mm

Height:

250

CAPACITY

M.E.P REQUIREMENT SPECIFICATIONS

PLUMBING : 400mm x 400mm x 150mm deep # 16 Ga. S.S. sink, SinkComplete with 50mm dia lever handle operated waste outlet.

One (1) No. deck Mounted “Jaksons Make” Swivel type waterMixer faucet.

No. 14 Ga. S.S. wall Brackets. Secured to top with acorn Nuts& Bolts & Bracket secured to wall with anchor fasteners.

Front & both sides # 20 GA S.S. apron.

Cold ∅ ½”

Hot ∅ ½”

Waste ∅ 2” Dr-Waste

ELECTRIC :

Power NA

Voltage NA

EXHAUST

NA

GAS:

BTU NA

Con. ∅ NA mm

ACCESSORIES:

SPECIAL NOTE: All Sheet /Pipe S.S. 304 Grade Pre-polished PlasticCoated.

Page 74: AMRITSAR SPECIFICATIONS FOR CUSTOM BUILT KITCHEN …sgpc.net/wp-content/uploads/2013/07/CUSTOM-BUILT... · INDIA Sector -17, Dwarka, New Delhi -110078 GENERAL SPECIFICATIONS FOR CUSTOM

Integrated Solution for Hospitality ProjectsAn ISO 9001:2000 Certified Company

CB. K. Eqpt /Specs GOLDEN TEMPLE - AMRITSAR Page- 74of 81INDIA Sector -17, Dwarka, New Delhi -110078

www.hpgconsulting.com

ITEM NO : CM-42 WORK TABLE

QUANTITY: 1 TENTATIVE IMAGE

CUSTOM BUILT

SIZE

Width:

1900 mm

Depth:

700 mm

Height:

850 mm

CAPACITY

M.E.P REQUIREMENT SPECIFICATIONS

PLUMBING : For construction detail refer standard shop drawing no. :-HPG/FD/23.

#16 Ga. S.S. Top.

150mm High Splash at Rear & left side.

Front & right sides turned down 50 mm & in 12mm

Rear & left side turned up 150 mm returned 25 mm & in12mm.

Top secured to 38mm x 38mm x 3mm thick S.S. weldedangle frame work.

Full length # 18 Ga. S.S. Bottom & intermediate shelves.

Six (6) no. 38mm Dia S.S. legs. With adjustable bullet feet.

Cold ∅ NA

Hot ∅ NA

Waste ∅ NA

ELECTRIC :

Power NA

Voltage NA

EXHAUST

NA

GAS:

BTU NA

Con. ∅ NA mm

ACCESSORIES:

SPECIAL NOTE: All Sheet /Pipe S.S. 304 Grade Pre-polished PlasticCoated.

Page 75: AMRITSAR SPECIFICATIONS FOR CUSTOM BUILT KITCHEN …sgpc.net/wp-content/uploads/2013/07/CUSTOM-BUILT... · INDIA Sector -17, Dwarka, New Delhi -110078 GENERAL SPECIFICATIONS FOR CUSTOM

Integrated Solution for Hospitality ProjectsAn ISO 9001:2000 Certified Company

CB. K. Eqpt /Specs GOLDEN TEMPLE - AMRITSAR Page- 75of 81INDIA Sector -17, Dwarka, New Delhi -110078

www.hpgconsulting.com

ITEM NO: CM-43 WORK TABLE W/SINK

QUANTITY: 1 TENTATIVE IMAGE

CUSTOM BUILT

SIZE :

Width:

1900 mm

Depth:

700 mm

Height:

850 mm

CAPACITY

M.E.P REQUIREMENT SPECIFICATIONS

PLUMBING : For construction detail refer standard shop drawing no. :-HPG/FD/13.

#16 Ga. S.S. Top.

150mm High at Rear & right Side Splash.

Front & left sides turned down 50 mm & in 12mm

Rear & right sides turned up 150 mm returned 25 mm & in12mm.

Top secured to 38mm x 38mm x 3mm thick S.S. weldedangle frame work.

Right of unit One (1) no. 450mm x 450mm x 200mm deep# 16 Ga. S.S. sink, Sink Complete with 50mm dia leverhandle operated waste outlet & rear connected overflow.

Six (6) no. 38mm Dia S.S. legs. With adjustable bullet feet.

25mm Dia S.S. pipe cross bracing welded to legs at Rear &both sides. Front open for garbage can.

# 20 G.A S.S Apron front of Sink.

One (1) No. Deck Mounted “Jaksons Make” Swivel typewater Mixer faucet.

Cold ∅ ½”

Hot ∅ ½”

Waste ∅ 2”

ELECTRIC :

Power NA

Voltage NA

EXHAUST

NA

GAS:

BTU NA

Con. ∅ NA mm

ACCESSORIES:

SPECIAL NOTE: All Sheet /Pipe S.S. 304 Grade Pre-polished Plastic Coated.

Page 76: AMRITSAR SPECIFICATIONS FOR CUSTOM BUILT KITCHEN …sgpc.net/wp-content/uploads/2013/07/CUSTOM-BUILT... · INDIA Sector -17, Dwarka, New Delhi -110078 GENERAL SPECIFICATIONS FOR CUSTOM

Integrated Solution for Hospitality ProjectsAn ISO 9001:2000 Certified Company

CB. K. Eqpt /Specs GOLDEN TEMPLE - AMRITSAR Page- 76of 81INDIA Sector -17, Dwarka, New Delhi -110078

www.hpgconsulting.com

ITEM NO : CM-44 FLUSHING HOSE UNIT

QUANTITY: 6

CUSTOM BUILT

SIZE

Length:

15 Mts.Hose reel.

Depth: Height:

CAPACITY

M.E.P REQUIREMENT SPECIFICATIONS

PLUMBING : Heavy duty Cast bronze Mixer Body, Suitable for mixing hot& cold water

S.S. stud bolts for grouting to wall at 1650 A.F.F.

15 MT. Dunlop Hose Reel with brass nozzle.

Heavy duty S.S. rod rack for winding hose when not use

Cold ∅ ¾”

Hot ∅ ¾”

Waste ∅ NA

ELECTRIC :

Power NA

Voltage NA

EXHAUST

NA

GAS:

BTU NA

Con. ∅ NA

ACCESSORIES:

SPECIAL NOTE: All Sheet /Pipe S.S. 304 Grade Pre-polished Plastic Coated.

Page 77: AMRITSAR SPECIFICATIONS FOR CUSTOM BUILT KITCHEN …sgpc.net/wp-content/uploads/2013/07/CUSTOM-BUILT... · INDIA Sector -17, Dwarka, New Delhi -110078 GENERAL SPECIFICATIONS FOR CUSTOM

Integrated Solution for Hospitality ProjectsAn ISO 9001:2000 Certified Company

CB. K. Eqpt /Specs GOLDEN TEMPLE - AMRITSAR Page- 77of 81INDIA Sector -17, Dwarka, New Delhi -110078

www.hpgconsulting.com

ITEM NO : CM-46 VEG PICK-UP TROLLEY

QUANTITY: 2 Tentative Image

CUSTOM BUILT

SIZE

Width:

1200 mm

Depth:

900 mm

Height:

850

CAPACITY

M.E.P REQUIREMENT SPECIFICATIONS

PLUMBING : 16 GA SS sheet covered all sides front open

Bottom 16 GA SS perforated sheet with 3mm hole with gapof approx.75mm.

25mm dia S.S. pipe handle.

Four (4) Nos. of Castors 150 mm dia x 50 mm thick heavy-duty Nylocast swivel type, two with brakes, fixed to achannel framework.

Cold ∅ NA

Hot ∅ NA

Waste ∅ NA

ELECTRIC :

Power NA

Voltage NA

EXHAUST

NA

GAS:

BTU NA

Con. ∅ NA mm

ACCESSORIES:

SPECIAL NOTE: All Sheet /Pipe S.S. 304 Grade Pre-polished PlasticCoated.

Page 78: AMRITSAR SPECIFICATIONS FOR CUSTOM BUILT KITCHEN …sgpc.net/wp-content/uploads/2013/07/CUSTOM-BUILT... · INDIA Sector -17, Dwarka, New Delhi -110078 GENERAL SPECIFICATIONS FOR CUSTOM

Integrated Solution for Hospitality ProjectsAn ISO 9001:2000 Certified Company

CB. K. Eqpt /Specs GOLDEN TEMPLE - AMRITSAR Page- 78of 81INDIA Sector -17, Dwarka, New Delhi -110078

www.hpgconsulting.com

ITEM NO : CM-47 VEG. WASHING TROLLEY

QUANTITY: 10 Tentative Image

CUSTOM BUILT

SIZE

Width:

900 mm

Depth:

600 mm

Height:

1050 mm

CAPACITY

M.E.P REQUIREMENT SPECIFICATIONS

PLUMBING : For construction detail refer standard shop drawing no. : -HPG/FD/06.

200mm high pan, 2.0mm thick S.S. pan welded constructionwith top edges all turned out 25mm, down 25mm and in12mm. Pan duly perforated.

Top and body secured to 50mm x 50mm x 2mm thick S.S.welded angle frame work.

38mm dia S.S. pipe handle with pipe reinforcement.

Four (4) no. heavy duty 150mm dia x 50mm thick Nonmarking rubberized castors all with brakes.

Cold ∅ NA

Hot ∅ NA

Waste ∅ NA

ELECTRIC :

Power NA

Voltage NA

EXHAUST

NA

GAS:

BTU NA

Con. ∅ NA mm

ACCESSORIES:

SPECIAL NOTE: All Sheet /Pipe S.S. 304 Grade Pre-polished PlasticCoated.

Page 79: AMRITSAR SPECIFICATIONS FOR CUSTOM BUILT KITCHEN …sgpc.net/wp-content/uploads/2013/07/CUSTOM-BUILT... · INDIA Sector -17, Dwarka, New Delhi -110078 GENERAL SPECIFICATIONS FOR CUSTOM

Integrated Solution for Hospitality ProjectsAn ISO 9001:2000 Certified Company

CB. K. Eqpt /Specs GOLDEN TEMPLE - AMRITSAR Page- 79of 81INDIA Sector -17, Dwarka, New Delhi -110078

www.hpgconsulting.com

ITEM NO : CM-47A VEG CRATE SOAKING MOBILE RACK

QUANTITY: 10 Tentative Image

CUSTOM BUILT

SIZE

Width:

900 mm

Depth:

600 mm

Height:

1800 mm

CAPACITY

M.E.P REQUIREMENT SPECIFICATIONS

PLUMBING : Four (5) no. # 18 Ga. S.S. Shelves pan shape.

# 18 GA. S.s. shelves turned up 25mm & hemmed.

All shelves having 1” dia drain and each shelves having slopetowards drain.

38mm x 38mm x # 16 Ga. S. S. square pipe uprights oncastor.

S.S. shelves welded to S.S. square pipe uprights at equalCentre & accommodate two no. Veg basket each shelves.

Four (4) no. Heavy duty 150 mm dia Non marking rubberizedcastors two with brakes.

Cold ∅ NA

Hot ∅ NA

Waste ∅ NA

ELECTRIC :

Power NA

Voltage NA

EXHAUST

NA

GAS:

BTU NA

Con. ∅ NA mm

ACCESSORIES:

SPECIAL NOTE: All Sheet /Pipe S.S. 304 Grade Pre-polished PlasticCoated.

Page 80: AMRITSAR SPECIFICATIONS FOR CUSTOM BUILT KITCHEN …sgpc.net/wp-content/uploads/2013/07/CUSTOM-BUILT... · INDIA Sector -17, Dwarka, New Delhi -110078 GENERAL SPECIFICATIONS FOR CUSTOM

Integrated Solution for Hospitality ProjectsAn ISO 9001:2000 Certified Company

CB. K. Eqpt /Specs GOLDEN TEMPLE - AMRITSAR Page- 80of 81INDIA Sector -17, Dwarka, New Delhi -110078

www.hpgconsulting.com

ITEM NO : CM-51 FLUSHING HOSE UNIT

QUANTITY: 1

CUSTOM BUILT

SIZE

Length:

15 Mts.Hose reel.

Depth: Height:

CAPACITY

M.E.P REQUIREMENT SPECIFICATIONS

PLUMBING : Heavy duty Cast bronze Mixer Body, Suitable for mixing hot& cold water

S.S. stud bolts for grouting to wall at 1650 A.F.F.

15 MT. Dunlop Hose Reel with brass nozzle.

Heavy duty S.S. rod rack for winding hose when not use

Cold ∅ ¾”

Hot ∅ ¾”

Waste ∅ NA

ELECTRIC :

Power NA

Voltage NA

EXHAUST

NA

GAS:

BTU NA

Con. ∅ NA

ACCESSORIES:

SPECIAL NOTE: All Sheet /Pipe S.S. 304 Grade Pre-polished Plastic Coated.

Page 81: AMRITSAR SPECIFICATIONS FOR CUSTOM BUILT KITCHEN …sgpc.net/wp-content/uploads/2013/07/CUSTOM-BUILT... · INDIA Sector -17, Dwarka, New Delhi -110078 GENERAL SPECIFICATIONS FOR CUSTOM

Integrated Solution for Hospitality ProjectsAn ISO 9001:2000 Certified Company

CB. K. Eqpt /Specs GOLDEN TEMPLE - AMRITSAR Page- 81of 81INDIA Sector -17, Dwarka, New Delhi -110078

www.hpgconsulting.com

ITEM NO : CM-53 MOBILE CHOPPING BOARD SANITIZERTROLLEY

QUANTITY: 4

CUSTOM BUILT

SIZE

Width:

610 mm

Depth:

610 mm

Height:

610mm

CAPACITY

M.E.P REQUIREMENT SPECIFICATIONS

PLUMBING : For construction detail refer standard shop drawing no. :-HPG/FD/62.

# 16 GA. S.S. w/ all sides channel shape.

535mm X 535mm X 305mm deep # 16 Ga. S.S. with allcorners coved 20mm radius , Complete with 38mm dia leverhandle operated waste outlet with Tail pipe extended at50mm A.F.F.

(4) no. 100mm dia Non marking rubberized castors two withbrakes.

S.S. Chopping board stand (size as per sink) approx 200mmx 6mm thick S.S. rod (Removable).

Cold ∅ NA

Hot ∅ NA

Waste

∅ NA

ELECTRIC :

Power NA

Voltage NA

EXHAUST

NA

GAS:

BTU NA

Con. ∅ NA mm

ACCESSORIES:

SPECIAL NOTE: All Sheet /Pipe S.S. 304 Grade Pre-polished Plastic Coated.


Recommended