of 5
8/20/2019 Analyzer CFD Overview V1 BV
1/10
Analyzer CAE Solutions Pvt. Ltd.Complete CAE Solutions…
CFD Capabilities at Analyzer
8/20/2019 Analyzer CFD Overview V1 BV
2/10
CFD Capabilities in:
Internal and External
Aerodynamics
Intake/exhaust manifolds
Underhood Analysis
Filtration and Exhaust Systems
Filtration System
Automotive Industry
External Aerodynamics Engine Simulation
Underhood thermal management
8/20/2019 Analyzer CFD Overview V1 BV
3/10
Electronic Cooling Areas of Expertise
Component Level Analysis
Virtual JEDAC TestsTheta JA, Theta JC, Theta JB, Theta CA, etc.
Detailed Modeling
Compact Thermal Model
2R and DELPHI Model
Board Level Analysis
Component Placement
Thermal Vias, Board Cu Layering, etc.
System Level Analysis
Overall System Thermal Performance
Casing, Internal Air, and Component Surface Temperature
Parameters Under Consideration
Peak Temperature/Hot Spots
Air flow rates and temperature
What if? Analysis
Effect of Heat sinks, fans, heat pipes, etc.
Design Optimization
8/20/2019 Analyzer CFD Overview V1 BV
4/10
Turbo-machinery Capabilities
Pumps (Single and Multi-Stage)
Mixed Flow
Axial Flow
Radial Flow
Compressors and turbines (Single and Multi-stage)
Fans and Blowers Cavitation Analysis
Automotive Application
Turbo Chargers
Radiator Fans
Parameters under investigation Head or Total Pressure Rise
Shaft Power
Efficiency
Stall or Flow Separation
8/20/2019 Analyzer CFD Overview V1 BV
5/10
Cooling Water Basin and Pump Sump Analysis
Relative Position of Sluice Gate and Pump Intake:-
The primary reason of the swirl is the relative position of sluice gate and pump intake, hence the
position needs to be optimized.
Vortex Breaker:-
By using appropriate Vortex Breakers,
vortex formation reduces significantly.
Separation Wall:-
By using Breast wall, overall vortex formation
and hydraulic fluctuations will reduce, this will improve
pump performance.
Introduction of slope:-
Introduction of Slope rather than step in the sump
pit, reduces flow recirculation and improves pump performance.
8/20/2019 Analyzer CFD Overview V1 BV
6/10
Ventilation and Fire/Smoke Simulation
Optimizing the location of fresh air and exhaust
location and number of jet fan required.
Locating the dead regions and high CO
concentration zones and eliminating them.
Tracing Smoke path and formulizing the emergency
evacuation.
Applications in:
Multi Level Car Park Ventilation
Malls and Airports
Tunnels
Commercial buildings
Bus and Railway Stations
8/20/2019 Analyzer CFD Overview V1 BV
7/10
Internal and External Building Simulation
CFD Simulation for Internal and External of
Buildings: CFD Simulation of Airports to determine the thermal
comfort of passengers inside the airport.
Fire and Smoke simulations inside the shopping mall
to determine the location of fresh air and exhaust fan
locations for best performance of system.
Determining the stack effect in tall buildings due to
AHU’s place one over another under various wind
speeds and wind directions.
Determining the flow pattern on building and to predict the effect of rain (Wind Driven Rain) on the
building.
HVAC simulation of Airports
Simulation of Fire Propagation in
Shopping Mall
Flow simulation on Building to determine the wind driven rain
Stack effect prediction due to Outdoor Units
8/20/2019 Analyzer CFD Overview V1 BV
8/10
Cyclone
ESP
Bag House
Ducting
Mixing
CFD in Process Industry
Ineffective outlets
Spray Dryer
8/20/2019 Analyzer CFD Overview V1 BV
9/10
Key Clients List
Some of the current customers
NAL Cunmmins Atlas Copco BHEL R&D
ThyssenKrupp Ashok LeylandLarsen & Toubro Limited
8/20/2019 Analyzer CFD Overview V1 BV
10/10
CFD
Thank You
HVAC in Data Centre
(Car/Buildings etc)
Aero-Acoustics in Intake Manifold (HVAC
ducts, Mufflers, combustors etc)
Flow through Pump
(Pipes/Valves etc)
Combustion in Fluidized
Bed (Furnas/Enginesetc)
External
Aerodynamics of Car
(any vehicle)
IC engine
simulation
Electronic Cooling
Ventilation and Smoke Simulation
(Transient Simulations)
