Hellenic Accreditation System Annex F1A/12 to the Certificate No. 159 -4 SCOPE of ACCREDITATION of the Laboratory for Non Destructive and Mechanical Tests of the "T.C.L. Co. - Test & Control Laboratories" AVRAMIDIS ELEFTHERIOS - DIPSAKIS ANTONIOS Co. (Athens Laboratory) Materials / Products to be tested Types of test / Properties to be measured Applied Methods / Techniques to be used A' Non destructive tests Metallic materials, products and fabrications, including weldings Penetration thickness: (1 -100) mm A1. Radiographic inspection using X and Gamma-rays (IR192&SE 75) ELOT EN 444: 1994 Non-destructive testing - General principles for radiographic examination of metallic materials by X and Gamma-rays Metallic materials, products and fabrications, including weldings Penetration thickness: (1 -100) mm A1. Radiographic inspection using X and Gamma-rays (IR192&SE 75) ELOT EN ISO 17636-1: 2013 Non-destructive testing of welds - Radiographic testing - Part 1: X- and gamma-ray technique with films Metallic materials, products and fabrications, including weldings Penetration thickness: (1 -100) mm A1. Radiographic inspection using X and Gamma-rays (IR192&SE 75) ELOT EN 10246-10: 2000 Non destructive testing of steel tubes. Part 10-radiographic testing of the weld seam of automatic fusion arc welded steel tubes for the detection of imperfections. Metallic materials, products and fabrications, including weldings Penetration thickness: (1 -100) mm A1. Radiographic inspection using X and Gamma-rays (IR192&SE 75) ASTM Ε 94: 2004 (2010) Standard Guide for Radiographic examination. Page 1 of 5 Annex F l A/12 to the Certificate ESYD No.159-4 10.10.2013
Transcript
Hellenic Accreditation System
Annex F1A/12 to the Certificate No. 159-4
SCOPE of ACCREDITATION of the
Laboratory for Non Destructive and Mechanical Tests of the
"T.C.L. Co. - Test & Control Laboratories" AVRAMIDIS ELEFTHERIOS - DIPSAKIS ANTONIOS Co.
(Athens Laboratory)
Materials / Products to be tested Types of test / Properties to be measured
Applied Methods / Techniques to be used
A ' N o n destructive tests
Metallic materials, products and fabrications, including weldings
Penetration thickness: (1 -100) mm
A1. Radiographic inspection using X and Gamma-rays ( I R 1 9 2 & S E 75)
ELOT EN 444: 1994 Non-destructive testing - General principles for radiographic examination of metallic materials by X and Gamma-rays
Metallic materials, products and fabrications, including weldings
Penetration thickness: (1 -100) mm
A1. Radiographic inspection using X and Gamma-rays ( I R 1 9 2 & S E 75)
ELOT EN ISO 17636-1: 2013 Non-destructive testing of welds -Radiographic testing - Part 1: X- and gamma-ray technique with films
Metallic materials, products and fabrications, including weldings
Penetration thickness: (1 -100) mm
A1. Radiographic inspection using X and Gamma-rays ( I R 1 9 2 & S E 75)
ELOT EN 10246-10: 2000 Non destructive testing of steel tubes. Part 10-radiographic testing of the weld seam of automatic fusion arc welded steel tubes for the detection of imperfections.
Metallic materials, products and fabrications, including weldings
Penetration thickness: (1 -100) mm
A1. Radiographic inspection using X and Gamma-rays ( I R 1 9 2 & S E 75)
ASTM Ε 94: 2004 (2010) Standard Guide for Radiographic examination.
Page 1 of 5 Annex F l A/12 to the Certificate E S Y D No.159-4 10.10.2013
Materials / Products to be tested Types of test / Properties to be measured
Applied Methods / Techniques to be used
Metallic materials, products and fabrications, including weldings
Penetration thickness: (1 -100) mm (cont.)
A1. Radiographic inspection using X and Gamma-rays ( IR192&SE75) (cont.)
ASME Boiler and pressure vessel code Section V: 2010 Non Destructive Examination Article 2: Radiographic Examination.
API 1104: 2005 Welding of pipelines and related facilities Paragraph 9.3 Radiographic testing
Weldments of metallic materials Base metal > 8 mm
A2. Ultrasonic testing ELOT EN 583-1: 1999 Non destructive testing. Ultrasonic examination. General principles
BS EN ISO 11666:2011 Non destructive testing of welds-Ultrasonic testing-Acceptance levels.
ELOT EN ISO 23279: 2012 Non destructive testing of welds-Ultrasonic testing-Characterization of indications in welds.
BS EN ISO 17640: 2011 Non destructive testing of welds-Ultrasonic testing - Techniques, testing levels and assessment.
ELOT EN 583-5: 2001 Non destructive testing. Ultrasonic examination. Part 5: characterization and sizing of discontinuities.
ELOT EN 10246-17: 2000 Non destructive testing of steel tubes. Part 17: ultrasonic testing of tube ends of seamless and welded steel tubes for the detection of laminar imperfections.
API 1104: 2005 Welding of pipelines and related facilities. Paragraph 9.6 Ultrasonic testing
Page 2 of 5 Annex F1A/12 to the Certificate E S Y D No.159-4 10.10.2013
Materials / Products to be tested Types of test / Properties to be measured
Weldments of metallic materials Base metal > 8 mm (cont.)
A2. Ultrasonic testing (cont.)
Metallic plates A3. Ultrasonic testing of plates
Ferromagnetic materials, products and fabrications, including weldments, castings and steel forgings
A4. Magnetic particle testing by the use of portable electromagnetic yoke Investigation for surface discontinuities
Applied Methods / Techniques to be used
ASME Boiler and pressure vessel code Section V: 2010 Non Destructive Examination Article 4: Ultrasonic examination methods for in-service inspection. Article 5: Ultrasonic examination methods for Materials and fabrication.
ELOT EN 10160: 1999 Ultrasonic testing of steel flat product of thickness equal or greater than 6mm (reflection method). Thickness > 6 mm
ASTM Ε 797/E797M: 2010 Standard practice for measuring thickness by manual ultrasonic pulse-echo contact method. Thickness > 1 mm
ELOT EN ISO 17638: 2011 Non destructive examination of welds-Magnetic particle testing of welds
ELOT EN 10246-12: 2000 Non destructive testing of steel tubes. Part 12: Magnetic particle inspection of seamless and welded ferromagnetic steel tubes for the detection of surface imperfections.
ELOT EN 10246-18: 2000 Non destructive testing of steel tubes. Part 18: magnetic particle inspection of tube ends of seamless and welded ferromagnetic steel tubes for the detection of laminar imperfections.
API 1104: 2005 Welding of pipelines and related facilities. Paragraph 9.4 magnetic particle testing
ASME Boiler and pressure vessel code Section V: 2010 Non Destructive Examination Article 7: Magnetic particle examination
ELOT EN 1369: 2012 Founding- Magnetic Particle Inspection
Page 3 of 5 Annex F l A/12 to the Certificate E S Y D No 159-4 10.10.2013
Materials / Products to be tested Types of test / Properties to be measured
Applied Methods / Techniques to be used
Ferromagnetic materials, products and fabrications, including weldments, castings and steel forgings (cont.)
A4. Magnetic particle testing by the use of portable electromagnetic yoke Investigation for surface discontinuities (cont.)
ELOT EN ISO 9934-1 : 2002 Non destructive testing-Magnetic Particle testing-Part 1:General Principles
Ferromagnetic materials, products and fabrications, including weldments, castings and steel forgings (cont.)
A4. Magnetic particle testing by the use of portable electromagnetic yoke Investigation for surface discontinuities (cont.)
ELOT EN 10228-1: 1999 Non destructive testing of steel forgings-Part 1: Magnetic particle inspection
Ferromagnetic materials, products and fabrications, including weldments, castings and steel forgings (cont.)
A4. Magnetic particle testing by the use of portable electromagnetic yoke Investigation for surface discontinuities (cont.)
ASTM Ε 709 : 2008 Standard practice for magnetic particle examination
Non porous materials, products and fabrications, including weldments, castings and steel forgings
A5. On site liquid penetrant testing Investigation for surface discontinuities
ELOT EN 571-1: 1997 Non destructive testing-Penetrant testing-Part 1: General principles
Non porous materials, products and fabrications, including weldments, castings and steel forgings
A5. On site liquid penetrant testing Investigation for surface discontinuities
ELOT EN ISO 23277: 2011 Non destructive testing of welds -Penetrant testing of welds -Acceptance levels.
Non porous materials, products and fabrications, including weldments, castings and steel forgings
A5. On site liquid penetrant testing Investigation for surface discontinuities
ELOT EN 10246-11: 2000 Non destructive testing of steel tubes. Part 11 : Liquid penetrant testing of seamless and welded steel tubes for the detection of surface imperfections
A5. On site liquid penetrant testing Investigation for surface discontinuities
API 1104: 2005 Welding of pipelines and related facilities Paragraph 9.5 : Liquid penetrant testing
A5. On site liquid penetrant testing Investigation for surface discontinuities
ASME Boiler and pressure vessel code Section V: 2010 Non Destructive Examination Article 6: Liquid penetrant examination.
A5. On site liquid penetrant testing Investigation for surface discontinuities
ELOT EN 10228-2 : 1998 Non destructive testing of steel forgings-Part 2: Penetrant testing
A5. On site liquid penetrant testing Investigation for surface discontinuities
ELOT EN 1371-1: 2012 Founding - Liquid penetrant inspection- Part 1 Sand, gravity die and low pressure die castings.
A5. On site liquid penetrant testing Investigation for surface discontinuities
ASTM E165/E165M - 12 Standard Practice for Liquid Penetrant Examination of General Industry
Page 4 of 5 Annex F l A/12 to the Certificate E S Y D No 159-4 10.10.2013
Materials / Products to be tested Types of test / Properties to be measured
Applied Methods / Techniques to be used
Weldings of metal structures A6. Visual testing (direct method only) BS EN ISO 17637: 2011 Non-destructive testing of welds -Visual testing of fusion-welded joints. ELOT EN ISO 5817:2008 Fusion-welded joints in steel, nickel, titanium and their alloys (beam welding excluded) - Quality levels for imperfections. ASME V art 9: 2010 ASME IXQW194: 2010 API 1104: 2005, § 6.4, 9.7
B ' Mechanical tests
Metallic materials and products, including weldings
B1. Tensile testing (0-200) kN (Only elongation after fracture and tensile strength)
EN ISO 4136: 2013 Destructive tests on welds in metallic materials - Transverse Tensile Test
Metallic materials and products, including weldings
B1. Tensile testing (0-200) kN (Only elongation after fracture and tensile strength) ELOT EN ISO 6892-1:2010
Metallic materials - Tensile testing -Part 1- Method of test at ambient temperature.
Metallic materials and products, including weldings
B1. Tensile testing (0-200) kN (Only elongation after fracture and tensile strength)
API 1104: 2005 Welding of pipelines and related facilities Paragraphs 5.6.2: Tensile strength test, 5.6.3: Nick break test.
Metallic materials and products, including weldings
B1. Tensile testing (0-200) kN (Only elongation after fracture and tensile strength)
ASME Boiler and pressure vessel code Section IX : 2010 QW 150 Tension tests
Metallic materials and products, including weldings
B2. Bend testing (0-200) kN
BS EN ISO5173:2010+A1: 2011 ELOT EN IS0 5173/A1: 2012 Destructive tests on welds in metallic materials - Bend tests
Metallic materials and products, including weldings
B2. Bend testing (0-200) kN
API 1104: 2005 Welding of pipelines and related facilities. Paragraphs 5.6.4: Root & Face bend test, 5.6.5: Side - bend test
Metallic materials and products, including weldings
B2. Bend testing (0-200) kN
ASME Boiler and pressure vessel code Section IX : 2010 QW 160 Guided bend tests
Site of assessment: Laboratory Permanent premises: Position Patima Rathiri, GR-19300 Aspropyrgos, Attiki, Greece. Approved signatories: A. Dipsakis.
This Scope of Accreditation replaces the previous one dated 11.07.2012. The Accreditation Certificate No. 159-4, to ELOT E N ISO/IEC 17025: 2005, is valid until 6.6.2016.
Page 5 of 5 Annex F l A/12 to the Certificate E S Y D No.159-4 10.10.2013
Hellenic Accreditation System
Annex F1B/10 to the Certificate No. 159-4
SCOPE of ACCREDITATION of the
Laboratory for Non Destructive and Mechanical Tests of the
"T.C.L. Co. - Test & Control Laboratories" AVRAMIDIS ELEFTHERIOS - DIPSAKIS ANTONIOS Co.
(Laboratory in Thessaloniki)
Materials / Products to be tested Types of test / Properties to be measured
Applied Methods / Techniques to be used
A ' N o n destructive tests
Metallic materials, products and fabrications, including weldings
Penetration thickness: (1 - 100) mm
A1. Radiographic inspection using X and Gamma-rays ( IR 192 & S E 7 5 )
ELOT EN 444: 1994 Non-destructive testing - General principles for radiographic examination of metallic materials by X and Gamma-rays
Metallic materials, products and fabrications, including weldings
Penetration thickness: (1 - 100) mm
A1. Radiographic inspection using X and Gamma-rays ( IR 192 & S E 7 5 )
ELOT EN ISO 17636-1: 2013 Non-destructive testing of welds -Radiographic testing - Part 1: X -and gamma-ray technique with films
Metallic materials, products and fabrications, including weldings
Penetration thickness: (1 - 100) mm
A1. Radiographic inspection using X and Gamma-rays ( IR 192 & S E 7 5 )
ELOT EN 10246-10: 2000 Non destructive testing of steel tubes. Part 10-radiographic testing of the weld seam of automatic fusion arc welded steel tubes for the detection of imperfections.
Metallic materials, products and fabrications, including weldings
Penetration thickness: (1 - 100) mm
A1. Radiographic inspection using X and Gamma-rays ( IR 192 & S E 7 5 )
A S T M Ε 94: 2004 (2010) Standard Guide for Radiographic examination.
Page 1 of 5 Annex FIB/10 to the Certificate E S Y D No.159-4 10.10.2013
Materials / Products to be tested Types of test / Properties to be measured
Applied Methods / Techniques to be used
Metallic materials, products and fabrications, including weldings
Penetration thickness: (1 -100) mm (cont.)
A1. Radiographic inspection using X and Gamma-rays ( I R 1 9 2 & S E 75) (cont.)
A S M E Boiler and pressure vessel code Section V: 2010 Non Destructive Examination Article 2: Radiographic Examination.
API 1104: 2005 Welding of pipelines and related facilities Paragraph 9.3 Radiographic testing
Weldments of metallic materials Base metal > 8 mm
A2. Ultrasonic testing ELOT EN 583-1:1999 Non destructive testing. Ultrasonic examination. General principles
BS EN ISO 11666:2011 Non destructive testing of welds-Ultrasonic testing-Acceptance levels.
ELOT EN ISO 23279: 2012 Non destructive testing of welds-Ultrasonic testing-Characterization of indications in welds.
BS EN ISO 17640: 2011 Non destructive testing of welds-Ultrasonic testing - Techniques, testing levels and assessment.
ELOT EN 583-5: 2001 Non destructive testing. Ultrasonic examination. Part 5: characterization and sizing of discontinuities.
ELOT EN 10246-17: 2000 Non destructive testing of steel tubes. Part 17: ultrasonic testing of tube ends of seamless and welded steel tubes for the detection of laminar imperfections.
API 1104: 2005 Welding of pipelines and related facilities. Paragraph 9.6 Ultrasonic testing
Page 2 of 5 Annex FIB/10 to the Certificate E S Y D No.159-4 10.10.2013
Materials / Products to be tested Types of test / Properties to be measured
Appl ied Methods / Techniques to be used
Weldments of metallic materials Base metal > 8 mm (cont.)
A2. Ultrasonic testing (cont.)
A S M E Boiler and pressure vessel code Section V: 2010 Non Destructive Examination Article 4: Ultrasonic examination methods for in-service inspection. Article 5: Ultrasonic examination methods for Materials and fabrication.
Metallic plates A3. Ultrasonic testing of plates ELOT EN 10160: 1999 Ultrasonic testing of steel flat product of thickness equal or greater than 6mm (reflection method). Thickness > 6 mm
Metallic plates A3. Ultrasonic testing of plates
A S T M Ε 797/E797M: 2010 Standard practice for measuring thickness by manual ultrasonic pulse-echo contact method. Thickness > 1 mm
Ferromagnetic materials, products and fabrications, including weldments, castings and steel forgings
A4. Magnetic particle testing by the use of portable electromagnetic yoke Investigation for surface discontinuities
ELOT EN ISO 17638: 2011 Non destructive examination of welds-Magnetic particle testing of welds
Ferromagnetic materials, products and fabrications, including weldments, castings and steel forgings
A4. Magnetic particle testing by the use of portable electromagnetic yoke Investigation for surface discontinuities
ELOT EN 10246-12 : 2000 Non destructive testing of steel tubes. Part 12: Magnetic particle inspection of seamless and welded ferromagnetic steel tubes for the detection of surface imperfections.
Ferromagnetic materials, products and fabrications, including weldments, castings and steel forgings
A4. Magnetic particle testing by the use of portable electromagnetic yoke Investigation for surface discontinuities
ELOT EN 10246-18: 2000 Non destructive testing of steel tubes. Part 18: magnetic particle inspection of tube ends of seamless and welded ferromagnetic steel tubes for the detection of laminar imperfections.
Ferromagnetic materials, products and fabrications, including weldments, castings and steel forgings
A4. Magnetic particle testing by the use of portable electromagnetic yoke Investigation for surface discontinuities
API 1104: 2005 Welding of pipelines and related facilities. Paragraph 9.4 magnetic particle testing
Ferromagnetic materials, products and fabrications, including weldments, castings and steel forgings
A4. Magnetic particle testing by the use of portable electromagnetic yoke Investigation for surface discontinuities
A S M E Boiler and pressure vessel code Section V: 2010 Non Destructive Examination Article 7: Magnetic particle examination
Ferromagnetic materials, products and fabrications, including weldments, castings and steel forgings
A4. Magnetic particle testing by the use of portable electromagnetic yoke Investigation for surface discontinuities
ELOT EN 1369: 2012 Founding- Magnetic Particle Inspection
Page 3 of 5 Annex FIB/10 to the Certificate E S Y D No.159-4 10.10.2013
Materials / Products to be tested Types of test / Properties to be measured
Applied Methods / Techniques to be used
Ferromagnetic materials, products and fabrications, including weldments, castings and steel forgings (cont.)
A4. Magnetic particle testing by the use of portable electromagnetic yoke Investigation for surface discontinuities (cont.)
ELOT EN ISO 9934-1 : 2002 Non destructive testing-Magnetic Particle testing-Part 1:General Principles ELOT EN 10228-1 : 1999 Non destructive testing of steel forgings-Part 1: Magnetic particle inspection
A S T M Ε 709 : 2008 Standard practice for magnetic particle examination
Non porous materials, products and fabrications, including weldments, castings and steel forgings
A5. On site liquid penetrant testing Investigation for surface discontinuities
ELOT EN 571-1: 1997 Non destructive testing-Penetrant testing-Part 1: General principles
ELOT EN ISO 23277: 2011 Non destructive testing of welds -Penetrant testing of welds -Acceptance levels.
ELOT EN 10246-11: 2000 Non destructive testing of steel tubes. Part 11 : Liquid penetrant testing of seamless and welded steel tubes for the detection of surface imperfections
API 1104: 2005 Welding of pipelines and related facilities Paragraph 9.5 : Liquid penetrant testing A S M E Boiler and pressure vessel code Section V: 2010 Non Destructive Examination Article 6: Liquid penetrant examination
ELOT EN 10228-2 : 1998 Non destructive testing of steel forgings-Part 2: Penetrant testing
ELOT EN 1371-1: 2012 Founding - Liquid penetrant inspection- Part 1 Sand, gravity die and low pressure die castings.
A S T M E 1 6 5 / E 1 6 5 M - 1 2 Standard Practice for Liquid Penetrant Examination of General Industry
Page 4 of 5 Annex FIB/10 to the Certificate E S Y D No.159-4 10.10.2013
Materials / Products to be tested Types of test / Properties to be measured
Applied Methods / Techniques to be used
Weldings of metal structures A6. Visual testing (direct method only)
BS EN ISO 17637: 2011 Non-destructive testing of welds -Visual testing of fusion-welded joints. ELOT EN ISO 5817: 2008 Fusion-welded joints in steel, nickel, titanium and their alloys (beam welding excluded) - Quality levels for imperfections. A S M E V art 9: 2010 A S M E IX QW194: 2010 API 1104: 2005, § 6.4, 9.7
B ' Mechanical tests
Metallic materials and products, including weldings
B1. Tensile testing (0-400) kN (Only elongation after fracture and tensile strength).
EN ISO 4136: 2013 Destructive tests on welds in metallic materials - Transverse Tensile Test
Metallic materials and products, including weldings
B1. Tensile testing (0-400) kN (Only elongation after fracture and tensile strength).
ELOT EN ISO 6892-1: 2010 Metallic materials - Tensile testing - Part 1- Method of test at ambient temperature.
Metallic materials and products, including weldings
B1. Tensile testing (0-400) kN (Only elongation after fracture and tensile strength).
API 1104: 2005 Welding of pipelines and related facilities Paragraphs 5.6.2: Tensile strength test, 5.6.3: Nick break test
Metallic materials and products, including weldings
B1. Tensile testing (0-400) kN (Only elongation after fracture and tensile strength).
A S M E Boiler and pressure vessel code Section IX : 2010 Q W 1 5 0 Tension tests
Metallic materials and products, including weldings
B2. Bend testing (0-400) kN
BS EN ISO 5173:2010+A1: 2011 ELOT E N ISO 5173/A1: 2012 Destructive tests on welds in metallic materials - Bend tests
Metallic materials and products, including weldings
B2. Bend testing (0-400) kN
API 1104: 2005 Welding of pipelines and related facilities. Paragraphs 5.6.4: Root & Face bend test, 5.6.5: Side - bend test
B2. Bend testing (0-400) kN
A S M E Boiler and pressure vessel code Section IX : 2010 Q W 160 Guided bend tests
Site of assessment: Laboratory Permanent premises: Agrotemachio 579, Municipality of Echedoros, Thessaloniki, Greece.
Approved signatories: El. Avramidis.
This Scope of Accreditation replaces the previous one dated 11.07.2012. The Accreditation Certificate No. 159-4, to ELOT E N ISO/IEC 17025: 2005, is valid until 6.6.2016.
![FLUID CHILLERS 28 TO 150 TONS - Delta Inddeltaind.net/wp-content/uploads/2019/08/012617_Chase... · 2019. 8. 21. · Tank Capacity [gal] 124 124 124 124 159 159 159 159 159 159 159](https://static.documents.pub/doc/80x56/613777b90ad5d2067648a37d/fluid-chillers-28-to-150-tons-delta-2019-8-21-tank-capacity-gal-124-124.jpg)
