Annual Report of the Association EURATOM/CEA 2001TW1-TPH-ICRANT ICRF Antenna and vacuum transmission...

Annual Report of the Association EURATOM/CEA

2001

Compiled by : Ph. MAGAUD and F. Le VAGUERES

ASSOCIATION EURATOM/CEADSM/DRFC

CEA/CADARACHE 13108 Saint-Paul-Lez-Durance (France)

FUSION TECHNOLOGY

Annual Report of the Association CEA/EURATOM

2001

Compiled by : Ph. MAGAUD and F. LE VAGUERES

ASSOCIATION CEA/EURATOM DSM/DRFC

CEA CADARACHE 13108 Saint-Paul-Lez-Durance (France)

Tél. : 33 - 4 42 25 46 59 Fax : 33 - 4 42 25 64 21 e-mail : [email protected] Web : http://www-fusion-magnetique.cea.fr

This report is also available on-line at : http://www-fusion-magnetique.cea.fr

Cover : Toroidal Field Model Coil (TFMC) installation and test 1 – Superconducting strand (courtesy of ENEA) 2&3 – Superconducting conductor (courtesy of ENEA) 4 – Cross section of the TMFC 5 – Superconducting joint 6 – TFMC at FZK (courtesy of FZK)

6

1

2

3

4

5

- I -

CONTENTS

INTRODUCTION ............................................................................................................ 1

EFDA TECHNOLOGY PROGRAMME ............................................................. 3

Physics Integration

Diagnostics CEFDA00-561 Support to ITER diagnostic design : polarimetry .................................................. 5 TW0-DIAG-DEV ITER diagnostic window development .................................................................. 7

Heating and Current Drive CEFDA00-553 Support to ITER-FEAT lower hybrid launcher and transmission line ................... 11 CEFDA00-546 Support to ITER ICRF system physics and engineering design - Electrical design of an ICRF array for high RF power density in ITER-FEAT ..... 15 CEFDA00-569 Development of vacuum coaxial capacitors for the ITER-like ICRF JET antenna ..................................................................... 19 TW0-ICRF/ANT ICRF Antenna and vacuum transmission line development - ICRH Antenna coupling : near field computations part II ..................................... 23 TW1-TPH-ICRANT ICRF Antenna and vacuum transmission line development - Design & manufacturing of a CW ICRF high power test rig and testing of next step antenna prototype components ........................................................... 29 TW0-NB.DEV.1 Neutral beam development for EDA extension - EU-JA collaborative experiment on KAMABOKO source ................................... 31

Vessel/In Vessel

Plasma Facing Components CNET98-480 Thermal fatigue testing of divertor full scale prototype - 200 kW electron beam gun test .............................................................................. 35 CNET98-485 Thermal fatigue testing of baffle full scale prototype - 200 kW electron beam gun test .............................................................................. 39 CEFDA00-543 High heat flux testing and analysis of small scale mock-ups - Part 2 : Analysis ..................................................................................................... 43 CEFDA00-565 Improvement evaluation for infrared detection of PFC defects - SATIR upgrading ................................................................................................... 47 CEFDA01-581 Critical heat flux testing of hypervapotrons - 200 kW electron beam gun test ...... 51

- II -

DV4.3 Optimisation and manufacture of high heat flux components - Study of flat tile cascade failure possibility for high heat flux components .......... 53 TW0-DV4/01 Optimisation of manufacture of high heat flux components : tungsten monoblocks ............................................................................................. 55 TW0-T438-01 Development and testing of time resolved erosion detecting techniques ............... 59 TW1-TVP-MAN1 Optimisation and testing optimisation of CuCrZr/SS tube joints - Optimisation and manufacturing of samples by diffusion bonding ....................... 63

Vessel/Blanket CEFDA00-556 Simulation of ultrasonic inspection process ........................................................... 67 CEFDA01-587 Study to evaluate ITER proposals for VV code use .............................................. 71 TW0-LASER/CUT VV intersector maintenance - Further development of high power Nd YAG laser cutting - Improvement of YAG laser backplate cutting by adding powder ... 73 TW0-LASER/HYD YAG laser process for cutting and welding of the blanket module hydraulic connections ............................................................................................................ 77 TW0-LASER/REWELD VV intersector maintenance - Further development of high power Nd - YAG laser rewelding after cutting ......................................................................... 81 TW0-LASER/WELD VV intersector joining - Further development of high power Nd - YAG laser welding with multipass filler wire ....................................................... 85 TW1-TVV-LWELD VV intersector joining - Vacuum vessel laser assembly ........................................ 87 T216-GB8 Small scale testing of first wall/shield modules ..................................................... 91 TW0-T420/06 Fabrication of a first wall panel with HIP’ed beryllium armor .............................. 93 TW0-T420/08 Development of HIP fabrication technique ........................................................... 99 TW0-T508/04 Development of Be/CuCrZr HIPping technique .................................................... 103 TW0-T508/05 Development of Be/CuCrCz brazing technique ..................................................... 105 TW1-TVV-HIP Improvement of HIP fabrication techniques .......................................................... 107 TW1-TVV-ONE Optimisation of one step SS/SS and SS/CuCrZr HIP joints for retainment of CuCrZr properties ............................................................................ 111

Remote Handling CEFDA00-524 Study to optimise intersector welding robot (IWR) design and machining characteristics ........................................................................................................ 115 T252 Radiation tolerance assessment of standard components for remote handling and process instrumentation .................................................................... 119 T329-5 In-vessel RH dexterous operations - Task extension 2 .......................................... 125 TW0-DTP/1.1 Carrier and bore tools for 4" bent pipes ................................................................. 129 TW1-TVA-BTS TW1-TVA-IVP Prototypical manipulator for access through IVVS penetrations (IVP) ................. 133 TW0-DTP1.2&4

- III -

TW1-TVA-MANIP In-vessel dexterous manipulator ............................................................................ 137 TW1-TVA-RADTOL Radiation tolerance assessment of remote handling components ........................... 139

Magnet Structure

Cryoplant CEFDA00-517 Design of cryogenic transfer lines and ring manifolds for ITER-FEAT ................ 143 CEFDA00-566 Layout of the cryoplant for RTO/RC ITER ........................................................... 145

Magnets CEFDA00-541 Magnet design on PF and correction coils : conceptual design and analysis ......... 147 M40 Design work on magnet R&D ................................................................................ 153 M50 Conductor R&D - Development of NbTi conductors for ITER PF coils ............... 157 TW0-T400/01 CSMC and TFMC installation and test .................................................................. 159 TW1-TMC-CODES Design and interpretation codes ............................................................................. 163 TW1-TMC-SCABLE Cable and conductor characterization .................................................................... 167

Tritium Breeding and Materials

Breeding Blanket Water Cooled Lithium Lead (WCLL) Blanket TW1-TTBA-001-D01 Test blanket module - Adaptation to next step machine ........................................ 169 TW1-TTBA-001-D04 Tritium breeding module adaptation to next step machine - Adaptation of thermal-hydraulic performance to ITER specification .................... 173 TW1-TTBA-002-D01 Blanket manufacturing techniques - Definition of specification of a demonstrator ........................................................ 175 TTBA-2.1 Blanket manufacturing techniques - Definition of specifications for demonstrators ....................................................... 179 TTBA-2.2 Blanket manufacturing techniques - Solid HIP demonstrator for fabrication and coating, fabrication of double wall tubes ................................ 183 TW1-TTBA-002-D02 Blanket manufacturing techniques - Solid HIP demonstrator for fabrication and coating, fabrication of double wall tubes ................................ 185 TW1-TTBA-002-D03 Blanket manufacturing techniques - DIADEMO experimental program - Results of U bent DWT tests on Pb-Li .................................................................. 189 TW1-TTBA-002-D05 Blanket manufacturing techniques - Integrated mixed-powder HIP fabrication route for TBM with DWT .................................................................... 193 TTBA-3.5 Coating qualification and irradiation tests - Permeation out-of-pile testing .......... 197 TW1-TTBA-004-D03 Processes and components - Blanket neutronic instrumentation ........................... 199

- IV -

TW1-TTBA-005-D02 Safety and licensing : Pb-17Li/water interactions ................................................. 201 TW1-TTBA-005-D03 Safety and licensing - TBM and TBM system safety ............................................ 203 TW1-TTBA-006-D02 MHD effects - Test and modelling of natural MHD convection ........................... 209 Helium Cooled Pebble Bed (HCPB) Blanket TW1-TTBB-002-D02 Blanket manufacturing techniques - Mock-up of first wall manufactured with alternative reduced cost fabrication technique ............................................... 213 TTBB-2.3 Blanket manufacturing techniques - First wall manufacturing by HIP forming technique ...................................................................................... 217 TW1-TTBB-005-D03 Development of ceramic breeder pebble beds - Characterization of Li2TiO3 pebble beds ............................................................... 219 TW1-TTBB-005-D04 Development of ceramic breeder pebble beds - Validation of Li2TiO3 fabrication with pre-industrial means of the lab fabrication steps - Mastering/optimisation .......................................................................................... 223

Structural materials development Advanced materials TW1-TTMA-001-D01 SiC-SiC ceramic composite - SiC-SiC composite development and characterization .......................................... 227 TW1-TTMA-001-D09 SiC-SiC ceramic composite - Joining development : process and mechanical characterization ............................................................... 231 Reduced Activation Ferritic Martensitic (RAFM) steels TW1-TTMS-001-D02 RAFM steels - Irradiation performance - Neutron irradiation to 30-35 dpa at 325°C ............................................................. 235 TW1-TTMS-002-D03 RAFM steels - Metallurgical and mechanical characterization - Characterization and physical metallurgy .............................................................. 239 TW1-TTMS-002-D04 RAFM steels - Metallurgical and mechanical characterization - Thermal ageing behaviour of EUROFER 97 ......................................................... 243 TW1-TTMS-002-D16 RAFM steels - Metallurgical and mechanical characterization - Mechanical properties of diffusion bonded welds (RAFM/RAFM HIP joint) ...... 247 TW1-TTMS-002-D18 RAFM steels - Metallurgical and mechanical characterization - Mechanical properties of HIP powder steel ........................................................... 251 SM-3-3 Corrosion in water conditions (EUROFER 97 and F82H ) ................................... 253 TW1-TTMS-003-D12 RAFM steels - Stress corrosion cracking in aqueous environments ...................... 257 TW1-TTMS-004-D02 RAFM steels - Qualification fabrication processes - Powder HIP processing & specification ................................................................ 259 SM-2-3-1 Mechanical properties of F82H weldments ........................................................... 263 TTMS-2.3.2 Mechanical properties of EUROFER 97 weldments ............................................. 265 TW1-TTMS-004-D04 RAFM steels - Qualification fabrication processes - EUROFER weldability ....... 267 TW1-TTMS-004-D05 RAFM steels - Qualification fabrication processes - Dissimilar welding with filler ................................................................................ 271

- V -

TW1-TTMS-004-D06 RAFM steels - Qualification fabrication processes - Solid HIP process qualification, application to complex shapes ............................ 275 TW1-TTMS-005-D02 RAFM steels - Rules for design, fabrication and inspection - Design code assessment and development ............................................................. 279 TW1-TTMS-005-D05 RAFM steels - Rules for design, fabrication and inspection - RAFM data collection and data base maintenance ................................................ 281 TW1-TTMS-006-D01 RAFM steels - Qualification of high performance steels - ODS process and qualification ............................................................................... 283 TTMS-6.3.1 RAFM steels - Qualification of high performance steels - TW1-TTMS-006-D03 Microstructure and mechanical properties ............................................................. 287 Neutron source TTMI-001 IFMIF - Accelerator facility ................................................................................... 291

Safety and Environment SEA5-1 Validation of computer codes and models ............................................................. 295 SEA5-2 Coherent system of codes for the ITER safety analysis - Validation of computer codes and models ............................................................. 299 TSW-2.1 Waste and decommissioning strategy - Improvement to an existing facility and possibilities for diminishing gas release .......................................................... 301 TSW-2.6 Waste and decommissioning strategy - Requirements of decommissioning and waste management strategies .................. 303 TW0-SEA4 In-vessel safety - Third set of pre and post calculation of in-vessel LOCA’s SEA4-4 on the new japanese “ICE” facility ........................................................................ 307 TW0-SEA3.5 In-vessel hydrogen deflagration/detonation analysis ............................................. 311 TW1-TSS-SEA3.5 SEA5.31 Validation of computer codes and models ............................................................. 313 TW1-TSS-SEA5 TW1-TSS-SERF2 Tritium releases and long term impacts ................................................................. 315

System Studies

Power Plant Conceptual Studies (PPCS) TW0-TRP-3D1 Analyze the sensitivity of achieving accident management ................................... 319 TW0-TRP-4D5 In-vessel components ............................................................................................. 321 TW1-TRP-PPCS1-D04 Model A (WCLL) - Consistency with the PPCS GDRD ....................................... 325 TW1-TRP-PPCS1-D10 Model A (WCLL) - Design integration ................................................................. 327 TW1-TRP-PPCS3-D01 Selection of advanced models - Assessment of Pb-17Li cooled blanket and divertor concepts using SiCf/SiC as structural material .................................. 331

- VI -

Socio-economic studies TW1-TRE-ECFA-D01 Externalities of fusion - Comparison of fusion external costs with advanced nuclear fission reactor ............................................................................................ 335 TW1-TRE-ECFA-D02 Externalities of fusion accident - Sensitivity analysis on plant model and site location ..................................................................................................... 339

JET Technology JET-EP-Div The JET EP divertor project .................................................................................. 343 JW0-FT-2.5 Tritium processes and waste management - Dedicated procedures for the detritiation of selected materials ............................. 347

UNDERLYING TECHNOLOGY PROGRAMME ........................................ 349

Physics Integration

Diagnostics UT-PE-HFW Transparent polycristalline windows ..................................................................... 351

Vessel/In Vessel

Plasma Facing Components UT-PFC&C-HIP Mechanical behaviour of HIP joints ...................................................................... 355 UT-VIV/PFC-BDG Boron doped graphites ........................................................................................... 359 UT-VIV/PFC-SIC/MJ Development of SiC/metal joining techniques ...................................................... 361 UT-VIV/PFC-W/Coat Development of thick W CVD coatings for divertor high heat flux components .................................................................. 365 UT-VIV/PFC-TMM Thermo-mechanical models ................................................................................... 369

Remote Handling UT-VIV/AM-Actuators Remote handling techniques - Advanced technologies for high performances actuators ............................................................................. 371 UT-VIV/AM-ECIr Remote handling techniques - Radiation tolerance assessment of electronic components from specific industrial technologies for remote handling and process instrumentation ................................................................................... 373 UT-VIV/AM-HMI Remote handling techniques - Graphical programming for remote handling techniques .............................................................................. 377 UT-VIV/AM-Hydro Remote handling techniques - Technology and control for hydraulic manipulator ...................................................................................... 381

- VII -


Breeding Blanket UT-TBM/BB-IMBLA Improved breeding blanket .................................................................................... 385 UT-TBM/MAT-LM/MAG Liquid metal corrosion under magnetic field ......................................................... 391 UT-TBM/MAT-LM/Refrac Compatibility of refractory materials with liquid alloys ........................................ 395 UT-TBM/MAT-LM/SiC Compatibility of SiCf/SiC composites with liquid Pb-17Li ................................... 399 UT-TBM/MAT-LM/WET Wetting of materials by liquid metals .................................................................... 405

Materials development Structural materials UT-TBM/MAT-BIM Dissimilar diffusion-bonded joints mechanical testing .......................................... 409 UT-SM&C-COR Metal and oxide thermodynamic stability and solubility in water cooling systems ...................................................................................................... 413 UT-SM&C-LAM/Weld Laser weldability of LAM steels (Eurofer 97) ....................................................... 417 UT-TBM/MAT-LAM/Mic Influence of the martensite morphology on the plasticity behaviour of the Eurofer steel ................................................................................................. 421 UT-TBM/MAT-LAM3 Microstructural investigation of Reduced Activation Ferritic-Martensitic (RAFM) steels by Small Angle Neutron Scattering (SANS) ................................. 425 UT-TBM/MAT-Mod Modelling of the resistance of the dislocation network to the combined effect of irradiation and stress - Comparison of a pulsed and a continuous irradiation on the secondary defects structure in an annealed 316L steel .............. 429 UT-TBM/MAT-ODS Development of forming and joining technologies for ODS steels ....................... 433

Fuel cycle UT-TBM/FC-SP Separation of the D/T mixture from helium in fusion reactors using superpermeable membranes - Superpermeation : nonmonotonous energy dependence at low energy ion bombardment and the effect of membrane carbidization on hydrogen pemeation through the niobium membrane ................. 437

Safety and Environment UT-S&E-BLK Blanket safety – Design of a test section for MHD experimental program ........... 441 UT-S&E-Mitig Evaluation and mitigation of the risk connected to air or water ingress ................ 443

System studies UT-SS-REL Reliability / availability assessment - Double walled tube concept, impact on the pressure tubes reliability / availability ............................................. 447

- VIII -

INERTIAL CONFINEMENT FUSION PROGRAMME ......................... 451 ICF01 Intense laser and particle beams dynamics for I.C.F. applications ........................ 453 ICF02 Cryogenic targets production using magnetic levitation ........................................ 457 ICF03 Laser-matter interaction at relativistic intensities and fast igniter studies ............. 461 ICF04 European collaborative experiment on the fast igniter concept ............................. 463 ICF-KiT-PRC Overview on power reactor concepts ..................................................................... 465

APPENDIX 1 : Directions contribution to the fusion programme .................... 469

APPENDIX 2 : Allocations of tasks ............................................................................ 473

APPENDIX 3 : Reports and publications .................................................................. 479

APPENDIX 4 : CEA tasks in alphabetical order .................................................... 491

APPENDIX 5 : CEA sites ............................................................................................... 497

- 469 -

Task Area Site

CEFDA00-561 Diagnostics CadaracheTW0-DIAG-DEV Diagnostics CadaracheCEFDA00-553 Heating CadaracheCEFDA00-546 Heating CadaracheCEFDA00-569 Heating CadaracheTW1-TPH-ICRANT Heating CadaracheTW0-NB.DEV.1 Heating CadaracheCEFDA00-565 PFC CadaracheCEFDA01-581 PFC CadaracheCNET98-480 PFC CadaracheCNET98-485 PFC CadaracheDV4.3 PFC CadaracheTW0-T438-01 PFC CadaracheM40 Magnets CadaracheM50 Magnets CadaracheTW0-T400-1 Magnets CadaracheTW1-TMC-SCABLE Magnets CadaracheCEFDA00-541 Magnets CadaracheTW1-TMC-CODES Magnets CadaracheJET-EP-Div JET/PFC Cadarache

CEFDA00-517 Magnets GrenobleCEFDA00-566 Magnets GrenobleICF02 ICF Grenoble

TTMI-001 IFMIF Saclay

CEFDA00-543 PFC SaclayCEFDA01-587 VMS SaclayTTBA-2.1 Blanket / WCLL SaclayTW1-TTBA-001-D01 Blanket / WCLL SaclayTW1-TTBA-002-D01 Blanket / WCLL SaclayTW1-TTBA-005-D03 Blanket / WCLL SaclaySEA5-2 Safety SaclayTW1-TRP-PPCS3-D01 Reactor Study SaclayUT-VIV/PFC-TMM PFC SaclayUT-TBM/BB-IMBLA Blanket SaclayUT-SS-REL System Study SaclayICF-KiT-PRC ICF Saclay

TW1-TTBA-002-D03 Blanket / WCLL CadaracheTW1-TTBA-006-D02 Blanket / WCLL CadaracheTW1-TTBA-005-D02 Blanket / WCLL CadaracheTSW-2.1 Safety CadaracheTSW-2.6 Safety CadaracheTW1-TSS-SEA3.5TW0-SEA3.5

Safety Cadarache

TW1-TSS-SEA5SEA5-31

Safety Cadarache

TW0-TRP-3D1 Reactor Study CadaracheTW0-TRP-4D5 Reactor Study CadaracheTW1-TRP-PPCS1-D04 Reactor Study CadaracheTW1-TRP-PPCS1-D10 Reactor Study CadaracheJW0-FT-2.5 JET / Safety CadaracheUT-S&E-Mitig Safety CadaracheUT-S&E-BLK Safety Cadarache

CEADirection des Sciences de

la Matière

Département de Recherche sur la Fusion Contrôlée

Direction de l'Energie Nucléaire

Département de Modélisationde Structures et Systèmes

Département d'Etude des Réacteurs

APPENDIX 1 : DIRECTIONS CONTRIBUTIONTO THE FUSION PROGRAMME

Département de RechercheFondamentale sur la Matière Condensée

DRFC

DRFMC

DSM

Département d'Astrophysique, de Physique des Particules, de Physique Nucléaire

et de l'Instrumentation Associée

DAPNIA

DEN DM2S (ex DMT)

DER

- 470 -

Task Area Site

TW1-TTMS-001-D02 Material / RAFM SaclayTW1-TTMS-002-D03 Material / RAFM SaclayTW1-TTMS-002-D04 Material / RAFM SaclayTW1-TTMS-005-D02 Material / RAFM SaclayTW1-TTMS-005-D05 Material / RAFM SaclayTW1-TTMS-006-D03 Material / RAFM SaclayUT-PFC&C-HIP Material SaclayUT-TBM/MAT-LAM3 Material / RAFM SaclayUT-TBM/MAT-Mod Material SaclayUT-TBM/MAT-LAM/Mic Material / RAFM Saclay

TTBA-3.5 Blanket / WCLL SaclaySM-3-3 Material SaclayTW1-TTMS-003-D12 Material SaclayUT-TBM/MAT-LM/Refrac Material / LiPb SaclayUT-TBM/MAT-LM/MAG Material / LiPb SaclayUT-TBM/MAT-LM/SiC Material / LiPb SaclayUT-TBM/MAT-LM/WET Material / LiPb SaclayUT-SM&C-COR Material Saclay

TW1-TTBA-004-D03 Blanket / WCLL Cadarache

SEA5-1 Safety Cadarache

TW1-TTBA-001-D04 Blanket / WCLL Cadarache

CEFDA00-556 Vessel / NDT SaclayTW0-LASER/CUT Vessel / Welding SaclayTW0-LASER/HYD Vessel / Welding SaclayTW0-LASER/REWELD Vessel / Welding SaclayTW0-LASER/WELD Vessel / Welding SaclayTW1-TVV-LWELD Vessel / Welding SaclayTW1-TTBB-005-D03 Blanket / HCPB SaclayTW1-TTBB-005-D04 Blanket / HCPB SaclaySM-2-3-1 Material / RAFM SaclayTTMS-2.3.2 Material / RAFM SaclayTW1-TTMS-004-D04 Material / RAFM SaclayTW1-TTMS-004-D05 Material / RAFM SaclayUT-PE-HFW Diagnostics SaclayUT-VIV/PFC-BDG PFC SaclayUT-SM&C-LAM/Weld Material / RAFM Saclay

T252 Electronics FontenayT329-5 Remote Handling FontenayTW0-DTP/1.1 Remote Handling FontenayTW1-TVA-BTS Remote Handling FontenayTW0-DTP/1.2&4 Remote Handling FontenayTW1-TVA-IVP Remote Handling FontenayTW1-TVA-MANIP Remote Handling FontenayTW1-TVA-RADTOL Electronics FontenayUT-VIV/AM-Actuators Remote Handling FontenayUT-VIV/AM-ECIr Electronics FontenayUT-VIV/AM-HMI Remote Handling FontenayUT-VIV/AM-Hydro Remote Handling Fontenay

Direction de la Recherche Technologique

DTA

Département des Matériaux pour le Nucléaire

Département de Physico-Chimie

DMN (ex DECM)

DPC (ex DECM)

DRT DECS (ex CE2M ex DPSA)

Département d'Elaboration et de Contrôle des Structures

DTSI (ex DPSA ex LETI)

Département des Technologies des Systèmes Intelligents

Département d'Etudes des Déchets

DED

Département d'Etudes des Combustibles

DEC

Département de Thermohydraulique et de Physique

DTP

- 471 -

Task Area Site

TW0-DV4/01 PFC GrenobleTW1-TVP-MAN1 PFC GrenobleT216-GB8 Vessel / fabrication GrenobleTW0-T420/06 Vessel / fabrication GrenobleTW0-T420/08 Vessel / fabrication GrenobleTW0-T508/04 Vessel / fabrication GrenobleTW0-T508/05 Vessel / fabrication GrenobleTW1-TVV-HIP Vessel / fabrication GrenobleTW1-TVV-ONE Vessel / fabrication GrenobleTTBA-2.2 Blanket / WCLL GrenobleTW1-TTBA-002-D02 Blanket / WCLL GrenobleTW1-TTBA-002-D05 Blanket / WCLL GrenobleTTBB-2.3 Blanket / HCPB GrenobleTW1-TTBB-002-D02 Blanket / HCPB GrenobleTW1-TTMA-001-D01 Material / SiC-SiC GrenobleTW1-TTMA-001-D09 Material / SiC-SiC GrenobleTW1-TTMS-002-D16 Material / RAFM GrenobleTW1-TTMS-002-D18 Material / RAFM GrenobleTW1-TTMS-004-D02 Material / RAFM GrenobleTW1-TTMS-004-D06 Material / RAFM GrenobleTW1-TTMS-006-D01 Material / RAFM GrenobleUT-VIV/PFC-SIC/MJ Material / SiC-SiC GrenobleUT-VIV/PFC-W/Coat PFC GrenobleUT-TBM/MAT-BIM Material GrenobleUT-TBM/MAT-ODS Material / RAFM Grenoble

SEA4-4 Safety AixTW0-SEA4 Safety Aix

CEFDA00-524 Remote Handling Cassis

UT-TBM/FC-SP Superpemeation SaclayICF03 ICF SaclayICF04 ICF Saclay

ICF-01 ICF Orsay

TW0-ICRF/ANT Heating Nancy

TW1-TSS-SERF2 Safety FontenayTW1-TRE-ECFA-D01 Externalities FontenayTW1-TRE-ECFA-D02 Externalities Fontenay

Technicatome

Département des Technologies pour les Energies Nouvelles

Ecole POLYTECHNIQUE

Université d'Orsay

EXTERNAL COLLABORATIONS

DTEN (ex DEM)

CEPN (Nuclear Protection Evaluation Center)

Université de Nancy

GAER

- 472 -

- 473 -

Unit Site Investigator

Physics Integration

Diagnostics

CEFDA00-561 Support to ITER diagnostic design : polarimetry DRFC Cadarache Gil C.

TW0-DIAG-DEV ITER diagnostic window development DRFC Cadarache Lippa M.

Heating and Current Drive

CEFDA00-553 Support to ITER-FEAT lower hybrid launcher and transmission line DRFC Cadarache Bibet Ph.

CEFDA00-546 Support to ITER ICRF system physics and engineering design - Electrical design of an ICRF array for high RF power density in ITER-FEAT

DRFC Cadarache Brémond S.

CEFDA00-569 Development of vacuum coaxial capacitors for the ITER-like ICRF JET DRFC Cadarache Brémond S.

TW0-ICRF/ANT ICRF antenna and vacuum transmission line development - ICRH antenna coupling : near field computations part II

Unancy Nancy Heuraux S.

TW1-TPH-ICRANT ICRF antenna and vacuum transmission line development - Design and manufacture of a CW ICRF high power test rig and testing of next step antenna prototype components

DRFC Cadarache Brémond S.

TW0-NB.DEV.1 Neutral beam development for EDA extension - EU-JA collaborative experiment on KAMABOKO source

DRFC Cadarache Boilson D.

Vessel/In Vessel

Plasma Facing Components

CEFDA00-543 High heat flux testing and analysis of small scale mock-ups - Part 2 : Analysis DM2S Saclay Salavy J.F.

CEFDA00-565 Improvement evaluation for the infrared detection of PFC defects - SATIR upgrading

DRFC Cadarache Durocher A.

CEFDA01-581 Critical heat flux testing of hypervapotrons - 200 kW electron beam gun test DRFC Cadarache Escourbiac F.

CNET98-480 Thermal fatigue testing of divertor full scale prototypes DRFC Cadarache Escourbiac F.

CNET98-485 Thermal fatigue testing of baffle full scale prototype - 200 kW electron beam gun test

DRFC Cadarache Escourbiac F.

DV4.3 Optimisation of manufacture of high heat flux components - Study of flat tile cascade failure possibility for high heat flux components

DRFC Cadarache Schlosser J.

TW0-DV4/01 Optimisation of manufacture of high heat flux components : tungsten monoblocks

DTEN Grenoble Rigal E.

TW0-T438-01 Development and testing of time resolved erosion detecting techniques DRFC Cadarache Gauthier E.

TW1-TVP-MAN1 Optimisation and testing optimisation of CuCrZr/SS Tube Joints ; Optimisation and manufacturing of samples by diffusion bonding

DTEN Grenoble Federzoni L.

Vessel/Blanket

CEFDA00-556 Simulation of ultrasonic inspection process DECS Saclay Mahaut S.

CEFDA01-587 Study to evaluate ITER proposals for VV code use DM2S Saclay Devos J.

TW0-LASER/CUT VV intersector maintenance - further development of high power ND Yag laser cutting - Improvement of YAG laser backplate cutting by adding powder

DECS Saclay Alfillé J.P.

TW0-LASER/HYD Yag laser process for cutting and welding of the blanket module hydraulic connections

DECS Saclay Alfillé J.P.

TW0-LASER/REWELD VV intersector maintenance - Further development of high power ND YAG laser rewelding after cutting

DECS Saclay Aubert P.

TW0-LASER/WELD VV intersector joining - Further development of high power Nd: YAG laser welding with multipass filler wire

DECS Saclay Aubert P.

TW1-TVV-LWELD VV Intersector Joining - Vacuum vessel laser assembly DECS Saclay Aubert P.

EFDA TECHNOLOGY PROGRAMME

APPENDIX 2 : ALLOCATIONS OF TASKS

- 474 -

T216-GB8 Small scale testing of first wall/shield modules DTEN Grenoble Saint-Antonin F.

TW0-T420/06 Fabrication of a first wall panel with HIP’ed beryllium armor DTEN Grenoble Bucci. Ph.

TW0-T420/08 Development of HIP fabrication technique DTEN Grenoble Bucci. Ph.

TW0-T508/04 Development of Be/CuCrZr HIPping technique DTEN Grenoble Saint-Antonin F.

TW0-T508/05 Development of Be/CuCrCz brazing technique DTEN Grenoble Saint-Antonin F.

TW1-TVV-HIP Improvement of HIP fabrication techniques DTEN Grenoble Bucci. Ph.

TW1-TVV-ONE Optimisation of one step SS/SS and SS/CuCrZr HIP joints for retainment of CuCrZr properties

DTEN Grenoble Briottet L.

Remote Handling

CEFDA00-524 Study to optimise intersector welding robot (IWR) design and machining characteristics

GAER Cassis Meja P.

T252 Radiation tolerance assessment of standard components for remote handling process instrumentation

DTSI Fontenay Giraud A.

T329-5 In-vessel RH dexterous operations - Task extension 2 DTSI Fontenay Gravez P.

TW0-DTP/1.1TW1-TVA-BTS

Carrier and bore tools for 4" bent pipes DTSI Fontenay Friconneau J.P.

TW0-DTP/1.2&4TW1-TVA-IVP

Prototypical manipulator for access through IVVS penetrations (IVP) DTSI Fontenay Friconneau J.P.

TW1-TVA-MANIP In-vessel dexterous manipulator DTSI Fontenay Friconneau J.P.

TW1-TVA-RADTOL Radiation tolerance assessment - Radiation tolerance assessment of remote handling components


Magnet Structure & Integration

Cryoplant

CEFDA00-517 Design of cryogenic transfer lines and ring manifolds for ITER-FEAT DRFMC Grenoble Millet F.

CEFDA00-566 Layout of the cryoplant for RTO/RC ITER DRFMC Grenoble Millet F.

Magnets

CEFDA00-541 Technical specifications for magnet design tasks DRFC Cadarache Duchateau J.L.

M40 Design work on magnet R&D DRFC Cadarache Libeyre P.

M50 Conductor R&D - Development of NbTi conductors for ITER PF coils DRFC Cadarache Decool P.

TW0-T400-1 CMSC and TFMC installation and test DRFC Cadarache Libeyre P.

TW1-TMC-CODES Design and interpretation codes DRFC Cadarache Martinez A.

TW1-TMC-SCABLE Cable and conductor characterization DRFC Cadarache Zani L.


Breeding Blanket

Water Cooled Lithium Lead (WCLL) Blanket

TW1-TTBA-001-D01 Test blanket module adaptation to next step machine DM2S Saclay Poitevin Y.

TW1-TTBA-001-D04 Tritium breeding module adaptation to next step machine : adaptation of thermal-hydraulic performance to ITER specification

DTP Cadarache Avakian G.

TW1-TTBA-002-D01 Blanket manufacturing techniques - Definition of specifications of a demonstrator

DM2S Saclay Li Puma A.

TTBA-2.1 Blanket manufacturing techniques - Definition of specifications for demonstrators

DM2S Saclay Poitevin Y.

TTBA-2.2 Blanket manufacturing techniques - Solid HIP demonstrator for fabrication and coating, fabrication of double wall tubes


TW1-TTBA-002-D02 Blanket manufacturing techniques - Solid HIP demonstrator for fabrication of double wall tubes


TW1-TTBA-002-D03 DIADEMO experimental program - Results of U bent DWT tests on Pb-Li DER Cadarache Cachon L.

- 475 -

TW1-TTBA-002-D05 Blanket manufacturing techniques - Integrated mixed-powder HIP fabrication route for TBM with DWT

DTEN Grenoble Bucci. Ph.

TTBA-3.5 Coating qualification and irradiation tests - Permeation out-of-pile testing DPC Saclay A. Terlain

TW1-TTBA-004-D03 Processes and components - Blanket neutronic instrumentation DED Cadarache Blandin C.

TW1-TTBA-005-D02 Safety and licensing DER Cadarache Sardain P.

TW1-TTBA-005-D03 Safety and licensing - TBM and TBM system safety DM2S Saclay Li Puma A.

TW1-TTBA-006-D02 MHD effects - Test and modeling of natural MHD convection DER Cadarache Cachon L.

Helium Cooled Pebble Bed (HCPB) Blanket

TW1-TTBB-002-D02 Blanket manufacturing techniques - Mock-up of first wall manufactured with alternative reduced cost fabrication technique


TTBB-2.3 Blanket manufacturing techniques - First wall manufacturing by HIP forming technique


TW1-TTBB-005-D03 Development of ceramic breeder pebble beds - Characterization of Li2TiO3

pebble bedsDECS Saclay Lulewicz J.D.

TW1-TTBB-005-D04 Development of ceramic breeder pebble beds - Validation of Li2TiO3 fabrication with pre-industrial means of the lab fabrication steps - Mastering/optimization

DECS Saclay Lulewicz J.D.

Structural Materials

Advanced Materials

TW1-TTMA-001-D01 SiC-SiC ceramic composites - SiC-SiC composite development and characterization

DTEN Grenoble Couturier R.

TW1-TTMA-001-D09 SiC-SiC ceramic composites : joining development - process and mechanical characterization

DTEN Grenoble Saint Antonin F.

Reduced Activation Ferritic Martensitic (RAFM) Steels

TW1-TTMS-001-D02 RAFM steels - Irradiation performance - Neutron irradiation to 30-35 dpa at 325°C

DMN Saclay Alamo A.

TW1-TTMS-002-D03 RAFM steels - Metallurgical and mechanical characterization - Characterization and physical metallurgy

DMN Saclay Alamo A.

TW1-TTMS-002-D04 RAFM steels - Metallurgical and mechanical characterization - Thermal ageing behaviour of EUROFER 97

DMN Saclay Alamo A.

TW1-TTMS-002-D16 RAFM steels - Metallurgical and mechanical characterization - Mechanical properties of diffusion bonded welds (RAFM/RAFM HIP joint)

DTEN Grenoble Bedel L.

TW1-TTMS-002-D18 RAFM steels - Metallurgical and mechanical characterization - Mechanical properties of HIP powder steel

DTEN Grenoble Gentzbittel J.M.

SM-3-3 Corrosion in water conditions (Eurofer97 and F82H ) DPC Saclay Raquet O.

TW1-TTMS-003-D12 RAFM steels - Stress Corrosion Cracking in aqueous environments DPC Saclay Raquet O.

TW1-TTMS-004-D02 RAFM steels - Qualification and fabrication processes - Powder HIP processing and specification

DTEN Grenoble Gentzbittel J.M.

SM-2-3-1 Mechanical properties of F82H weldments DECS Saclay Fontes A.

TTMS-2.3.2 Mechnical properties of Eurofer97 weldments DECS Saclay Fontes A.

TW1-TTMS-004-D04 RAFM steels - Qualification Fabrication Processes - Eurofer Weldability DECS Saclay Fontes A.

TW1-TTMS-004-D05 RAFM steels - Qualification and fabrication processes - Dissimilar welding with filler

DECS Saclay Fontes A.

TW1-TTMS-004-D06 RAFM steels - Qualification and fabrication processes - Solid HIP process qualification, application to complex shapes


TW1-TTMS-005-D02 RAFM steels - Rules for design, fabrication and inspection - Design code assessment and development

DMN Saclay Tavassoli F.

TW1-TTMS-005-D05 RAFM steels - Rules for design, fabrication and inspection - RAFM data collection and data base maintenance

DMN Saclay Tavassoli F.

TW1-TTMS-006-D01 RAFM steels - Qualification of high performance steels - ODS process and qualification

DTEN Grenoble Cayron C.

TW1-TTMS-006-D03 RAFM steels - Qualification of high performance steels - Microstructure and mechanical properties

DMN Saclay Alamo A.

- 476 -

Neutron Source

TTMI-001 IFMIF, accelerator facility DAPNIA Saclay Ferdinand R.

Safety and Environment

SEA5-1 Validation of computer codes and models DEC Cadarache Tarabelli

SEA5-2 Coherent system of codes for the ITER safety analysis - Validation of computer codes and models

DM2S Saclay Toumi I.

TSW-2.1 Waste and decommissioning strategy - Improvement to an existing facility and possibilities for diminishing gas release

DER Cadarache Rosanvallon S.

TSW-2.6 Waste and decommissioning strategy - Requirements of decommissioning and waste management strategies


TW0-SEA4SEA4-4

In-vessel safety DER + TA Cadarache Sardain P.

TW1-TSS-SEA3.5TW0-SEA3.5

In-vessel hydrogen deflagration/detonation analysis DER Cadarache Sardain P.

TW1-TSS-SEA5SEA5.31

Validation of computer codes and models DER Cadarache Sardain P.

TW1-TSS-SERF2 Externalities of fusion - Tritium releases and long term impacts CEPN Fontenay Schneider Th.

System studies

Power Plant Conceptual Studies (PPCS)

TW0-TRP-3D1 Analyze the sensitivity of achieving the accident management DER Cadarache Sardain P.

TW0-TRP-4D5 In-vessel components DER Cadarache Michel B.

TW1-TRP-PPCS1-D04 Model A (WCLL) : consistency with the PPCS GDRD DER Cadarache Sardain P.

TW1-TRP-PPCS1-D10 Model A (WCLL) design integration DER Cadarache Sardain P.

TW1-TRP-PPCS3-D01 Selection of advanced models - Assessment of Pb-17Li cooled blanket and divertor concepts using SiCf/SiC as structural material

DM2S Saclay Golfier H.

Socio-economic Studies

TW1-TRE-ECFA-D01 Externalities of fusion - Comparison of fusion external costs with advanced nuclear fission reactor

CEPN Fontenay Schneider Th.

TW1-TRE-ECFA-D02 Externalities of fusion accident - sensitivity analysis on plant model and site location

CEPN Fontenay Schneider Th.

JET

JET-EP-Div The JET EP divertor project DRFC Cadarache Chappuis Ph.

JW0-FT-2.5 Tritium processes and waste management - Dedicated procedures for the detritiation of selected materials


Physics Integration

UT-PE-HFW Transparent polycristalline windows DECS Saclay Lochet N.

Vessel/In Vessel


UT-PFC&C-HIP Mechanical behaviour of HIP joints DMN Saclay Fissolo A.

UT-VIV/PFC-BDG Boron doped graphites DECS Saclay Lochet N.

UT-VIV/PFC-SIC/MJ Development of SiC/metal joining techniques DTEN Grenoble Delette G.

UT-VIV/PFC-W/Coat Development of thick W CVD coatings for divertor high heat flux components DTEN Grenoble Plissonnier M.

UT-VIV/PFC-TMM Thermo-mechanical models DM2S Saclay Nicolas A.

UNDERLYING TECHNOLOGY PROGRAMME

- 477 -

Remote Handling

UT-VIV/AM-Actuators Remote handling techniques - Advanced technologies for high performances actuators

DTSI Fontenay Friconneau J.P.

UT-VIV/AM-ECIr Remote handling techniques - Radiation tolerance assessment of electronic components from specific industrial technologies for remote handling and process instrumentation


UT-VIV/AM-HMI Remote handling techniques - Graphical programming for remote handling techniques

DTSI Fontenay Chodorge L.

UT-VIV/AM-Hydro Remote handling techniques - Technologies and control for hydraulic manipulator

DTSI Fontenay Friconneau J.P.


Breeding Blanket

UT-TBM/BB-IMBLA Improved Breeding Blanket DM2S Saclay Li Puma A.

UT-TBM/MAT-LM/MAG Liquid metal corrosion under magnetic field DPC Saclay Terlain A.

UT-TBM/MAT-LM/Refrac Corrosion behaviour of refractory materials with liquid alloys DPC Saclay Dufrenoy T.

UT-TBM/MAT-LM/SiC Compatibility of SiC/SiC composites with liquid Pb-17Li DPC Saclay Deloffre Ph.

UT-TBM/MAT-LM/WET Wetting of materials by liquid metals DPC Saclay Terlain A.

Materials Development

UT-TBM/MAT-BIM Dissimilar diffusion-bonded joints mechanical testing DTEN Grenoble Bedel L.

UT-SM&C-COR Metal and oxide thermodynamic stability and solubility in water cooling DPC Saclay Féron D.

UT-SM&C-LAM/Weld Laser weldability of LAM steels (Eurofer97) DECS Saclay Aubert Ph.

UT-TBM/MAT-LAM/Mic Influence of the martensite morphology on the plasticity behaviour of the Eurofer steel

DMN Saclay De Carlan Y.

UT-TBM/MAT-LAM3 Microstructural investigation of Reduced Activation Ferritic-Martensitic (RAFM) steels by Small Angle Neutron Scattering (SANS)

DMN Saclay De Carlan Y.

UT-TBM/MAT-Mod Modelling of the resistance of the dislocation network to the combined effect of irradiation and stress - Comparison of a pulsed and a continuous irradiation on the secondary defects structure in an annealed 316L steel

DMN Saclay Boulanger L.

UT-TBM/MAT-ODS Development of forming and joining technologies for ODS steels DTEN Grenoble Cayron C.

Fuel Cycle

UT-TBM/FC-SP Separation of the D/T mixture from helium in fusion reactors using superpermeable membranes - Superpermeation : non-monotonous energy dependence at low energy ion bombardment and the effect of membrane carbidization on hydrogen pemeation through the niobium membrane

EP-LPTP Palaiseau Bacal M.

Safety

UT-S&E-BLK Blanket safety DER Cadarache Sardain P.

UT-S&E-Mitig Evaluation and mitigation of the risk connected with air or water ingress DER Cadarache Robin J.C.

System Studies

UT-SM&C-REL Reliability/availability assessment - Double wall tube concept, impact on the pressure tubes reliability/availability

DM2S Saclay Eid M.

ICF01 Intense laser and particles beams dynamics for ICF applications Université Orsay Deutsch C.

ICF02 Cryogenic targets production using magnetic levitation DRFMC Grenoble Chatain D.

ICF03 Laser-matter interaction at relativistic intensities and fast igniter studies EP-LULI Palaiseau Migus A.

ICF04 European collaborative experiment on the fast igniter concept EP-LULI Palaiseau Migus A.

ICF-KiT-PRC Overview on power reactor concepts DM2S Saclay Eid M.

INERTIAL CONFINEMENT FUSION PROGRAMME

- 478 -

- 479 -

EFDA TECHNOLOGY PROGRAMME

Physics Integration

Diagnostics

TW0-DIAG-DEV ITER diagnostic window development-task 5.1a(PE), CEA/DRFC - FinalReport, Cadarache, August 2001.

M. Lipa, Ch. Portafaix

TW0-DIAG-DEV Development and testing of diagnostic windows for Tore Supra/CIEL andITER. ISFNT6, San Diego/ USA, April 2002, to be presented.

M. Lipa, Ch. Portafaix, E. Pluyette,N. Lochet et al.

TW0-DIAG-DEV IRIFA : Thermomechanical qualification of diagnostic windows under highIR radiative flux. ISFNT6, San Diego/USA,April 2002, to be presented.

E. Pluyette, J.P. Dieppois, F. Challetet al.

Heating and Current Drive

CEFDA00-546 EFDA Contract 00/546 Final Report, Electrical design of an IC array for high RF power density in ITER-FEAT. CEA Report DSM/DRFC/ CH/NTT – 2001.015, September 2001.

S. Brémond

CEFDA00-553 Report on ITER-FEAT launcher. Contract FU05 - CT 2001-00019 (CEA : EFDA/00-553, ENEA : EFDA/00-554)

CEFDA00-553 Report on the transmission line of the LH system on ITER FEATContract FU05 - CT 2001-00019 (CEA : EFDA/00-553, ENEA : EFDA/00-554)

CEFDA00-569 EFDA 00/569 contract : Final report Vacuum Coaxial Capacitors for JET-EP ICRF Antenna. CH/NTT-2002.001

TW0-ICRF/ANT ICRH antenna coupling: near field computations. Annual report association EURATOM/CEA 2000 p 7-10.

S. Heuraux, S. Pécoul

TW0-ICRF/ANT Numerical modeling of the coupling of an ICRH antenna with a plasma with self-consistent antenna current. Computational Physics Communications (à paraître).

S. Pécoul, S. Heuraux, R. Kochand G. Leclert

TW0-ICRF/ANT Edge plasma density convection during ICRH on Tore SupraPhys. Plasmas (à paraître).

M. Bécoulet, L. Colas, S. Pécoul,J. Gunn, Ph. Ghendrih, A. Bécoulet,S. Heuraux

TW0-NB.DEV.1 RSI 73, 2 (2002) D. Boilson, H.P.L. de Esch,R.S. Hemsworth, M. Kashiwagi,P. Massmann and L. Svensson

TW0-NB.DEV.1 Filter variation and long pulse operation of the KAMABOKO III source on the MANTIS test bed. Meeting of the co-ordination Committee for Neutral Beams, Cadarache France 14/15 April 2001.

L. Svensson, D. Boilson,H.P.L. de Esch, R.S. Hemsworth,M. Kashiwagi and P. Massmann

TW0-NB.DEV.1 Magnetic filter variation study on the KAMABOKO III sourceITER review meeting, Naka Japan, 28-31 May 2001.

L. Svensson, D. Boilson,H.P.L. de Esch, R.S. Hemsworthand P. Massmann

TW0-NB.DEV.1 Filter Variation and Long Pulse Operation of the KAMABOKO III source on the MANTIS test bed. Neutral Beam Development for EDA Extension, R&D TASK T512 Final report.

L. Svensson, D. Boilson,H.P.L. de Esch, R.S. Hemsworth,M. Kashiwagi, and P. Massmann

Vessel/In Vessel


CEFDA00-543 High heat flux testing and analysis of small scale mock-ups - Part 2: analysisCEA report DEN/DM2S SEMT/BCCR/RT/01-022/A, November 2001.

J-F. Salavy, F. Picard

APPENDIX 3 : REPORTS AND PUBLICATIONS (2001)

- 480 -

CNET98-480 Contract 98-480 : Thermal fatigue testing of divertor full scale prototypes - Final report CEA. CFP/NTT-2001.026 – feb. 2002

F. Escourbiac

CNET98-485 Contract 98-485 : Thermal fatigue of baffle full scale prototypes – Final Report CEA. CFP/NTT-2001.025 – Fev. 2002

F. Escourbiac

TW0-DV4/01 Optimisation of manufacturing of high heat flux components for ITER divertor. CEA Report NT DTEN n°62/2001, 28 june 2001.

E Rigal, C Grandjacques, F Bruchon

TW0-T438-01 Etude de faisabilité de mesure d'ablation par interférométrie speckle à deux longueurs d'onde. CFP/CRM-2001.006

G. Roupillard, E. Gauthier

TW0-T438-01 Mesures du coefficient de réflexion du CFC dans le visible par l'Institut Fresnel (12.06.2001) CFP/CRM-2001.011

G. Roupillard, E. Gauthier

TW0-T438-01 Compte rendu de réunion au DPC à Saclay le 24 juillet 2001. CFP/CRR-2001.012

E. Gauthier

TW0-T438-01 Etude de l’érosion des composants face au plasma dans Tore Supra par interférométrie speckle. Proceedings de la conférence de la Société Française d’Optique, 21-24 nov 2001, Trégastel.

G. Roupillard, E. Gauthier,V. Chalvidan

TW1-TVP-MAN1 Optimisation of Cu-SS tune joints. TVP-MAN1, Note technique DTEN n° 2001/119

L. Federzoni, P. Revirand

Vessel/Blanket

CEFDA00-556 Simulation of ultrasonic inspection process. DECS/STA/LMUS01-088

CEFDA01-587 Evaluation of ITER proposal for VV code use. CEA report DM2S SEMT/DIR/RT/01-004/A (June, 6, 2001)

F. Touboul

TW0-LASER/HYD Final report. CW YAG laser process for cutting and welding of the blanket module hydraulic connection. Technical report CLFA/01-335/JPA, August 2001

J.P. Alfillé et al

TW0-LASER/REWELD VV intersector maintenance- Further development of High Power Nd YAG laser rewelding after cutting. 06/2001

F. Coste

TW0-LASER/WELD VV Inter sector joining - Further development of High power ND YAG laser Welding with multi-passes filler wire. Réf.00/014 Final Report. 06/2001

F. Coste

TW0-T420/06 Fabrication of a first wall panel with HIP’ed beryllium armor. EFDA TW0-T420/06, Note technique DEM 52/2001.

Ph. Bucci, S. Täthinen, I. Chu,J. Calapez, J.M. Leibold

TW0-T420/06 Fabrication of a first wall panel with HIP’ed beryllium armor. EFDA TWO-T420/06, Note technique DEM 26/2002.

Ph. Bucci, J.M. Leibold, T. Portra

TW0-T420/08 Development of HIP fabrication technique. EFDA TW0-420/08, Note technique DEM 53-2001.

P. Bucci, J. Calapez, J.M. Leibold

TW0-T508/05 Development of Be/CuCrZr brazing techniques. Note Technique DTEN n°120/2001, 18 December 2001.

F. Saint-Antonin, G. Bourgeois

TW1-TVV-HIP EFDA TW1-TVV-HIP Improvement of HIP Fabrication Technique. Note Technique DEM n°131/2001, Décembre 2001.

L. Sanchez, P. Bucci, J.M. Leibold,P. Revirand

TW1-TVV-LWELD Nd:Yag laser welding of 60 mm thickness 316L parts using multiple passes Proceedings of ICALEO'2001. Conf Jaksonville (USA)

F. Coste, L. Sabatier, O. Dubet,P. Aubert, L. Jones

TW1-TVV-LWELD 20 mm thickness Nd:Yag Laser Welding of 316 L stainless steel with long focal length. Proceedings of ICALEO'2001. Conf Jaksonville (USA).

F. Coste, L. Sabatier, O. Dubet,P. Aubert, L. Jones

TW1-TVV-LWELD Note technique – 01 P024 ITER/Two laser Weld 12/2001 F. Coste

TW1-TVV-ONE Development of one step SS/SS and CuCrZr/SS HIP joints including DS-15F and PH/S-6F fabrication. EFDA TW-T427/03, CEA report DTEN n°2001/23.

L. Briottet, I. Chu

TW1-TVV-ONE Optimization of one Stepp SS/SS and SS/CuCrZr HIP joints for retainment of CuCrZr properties. EFDA TW1-TVV-ONE, intermediate report : milestones M1 to M4, CEA report DTEN n°2001/132.

L. Briottet, I. Chu, N. Scheer

- 481 -

Remote Handling

T252 Characterization of power transistors and low voltage logic circuits at high dose and temperature - Presented at RADECS 2001

JP. Le Gac

T252 Characterization of low voltage SRAM response to gamma radiationpresented at RADECS 2001

A. Giraud

T329-5 T329-5 : In-vessel RH dextrous operations – Water hydraulic joint results on qualification for force feedback application. Technical Report SRSI/LCI/01RT.040

C. Andriot

T329-5 T329-5 : In-vessel RH dextrous operations – Long distance teleoperation test report. Technical Report SRSI/LCI/01RT.042

C. Leroy

TW1-TVA-IVP In-Vessel Penetrator (IVP) Manufacture and test of a demonstrator report CEA/DTSI/SRSI/LPR/01RT.053/ Issue.0

TW1-TVA-MANIP Objectives and first modelling analyses. CEA/DTSI/SRSI/LCI/01RT.088/Issue 0

L. Chodorge, C. Bidard

TW1-TVA-BTS CWIE Laser module integration tests. Report CEA/DTSI/SRSI/LPR/01RT.025 Issue 0

TW1-TVA-BTS Swaging with the BTS carrier. Report CEA/DTSI/SRSI/LPR/02.RT.006

TW1-TVA-BTS Overview of bore tools systems for Divertor remote maintenance of ITER. SOFT 2000 and Fusion engineering and design 58-59 (2001)

JP. Friconneau & al

Magnet Structure

Cryoplant

CEFDA00-517 Final Report : Design of cryogenic transfer lines and ring manifolds for ITER-FEAT. ITER task agreement N 34 TD 04 FE // EFDA / 00-517 // FU05-CT 2000-00047 Note SBT/CT/01-35, July 2001

F. Millet

CEFDA00-517 Part 1 Report : Cost estimate for the cryoplant. ITER task agreement N 34 TD 06 FE // EFDA / 00-566 // FU05-CT 2001-00026 Note SBT/CT/00-66, December 2000

F. Millet

CEFDA00-566 Part 1 Report : Cost estimate for the cryoplant. ITER task agreement N 34 TD 06 FE // EFDA / 00-566 // FU05-CT 2001-00026 Note SBT/CT/00-66, December 2000

F. Millet

CEFDA00-566 Final Report : Layout of the cryoplant for RTO/RC ITERITER task agreement N 34 TD 06 FE // EFDA / 00-566 // FU05-CT 2001-00026 Note SBT/CT/01-36, July 2001

F. Millet

Magnets

CEFDA00-541 Electrical and thermal designs and analyses of joints for the ITER PF coils. Presented at the 17 th International Conference on Magnet Technology, Geneva September 2001.

D. Ciazynski, A. Martinez,

CEFDA00-541 Contract EFDA 00-541 Sub Task 1 Phase 2 conductor analysis (Revision 1) Internal note AIM/NTT 2001-037.

J.L Duchateau, D. Ciazynski,S. Nicollet.

CEFDA00-541 Conductor analysis of the ITER FEAT poloidal field coils during a plasma scenario. Presented at the CEC-ICMC Conference, Portland USA 2001.

S. Nicollet, P. Hertout, J.L Duchateau, A. Bleyer, D. Bessette.

CEFDA00-541 Characterization of transport properties variations with magnetic field and temperature of ITER-candidate NbTi strands. presented at EUCAS 2001 (Copenhaguen)

L. Zani and al.

CEFDA00-541 CS cooling inlets design and mechanical calculation. Internal note AIM/NTT 2001-035

P. Decool

CEFDA00-541 ITER FEAT CS cooling inlets hydraulic characterization and application to PF coils. Internal note AIM/NTT 2001-043

S. Nicollet, H. Cloez, P. Decool,J.P. Serries,

- 482 -

CEFDA00-541 Mechanical design and analysis of joints for the ITER PF coils. Presented at the 17 th International Conference on Magnet Technology, Geneva September 2001.

P. Libeyre, P. Decool

M40 Conceptual design of the ITER TF Model Coil, IEEE Trans. on Mag., P. Libeyre et al.

M40 Joints for large superconducting conductors, Fusion Eng. And Design, Vol. 58-59 , November 2001, pp. 123-127

P. Decool et al.

M40 Large superconductors and joints for fusion magnets : from conceptual design to test at full scale, Nuclear Fusion, vol.41 n°2 (2001) p.223-226

D. Ciazynski et al.

M50 Critical properties of ITER PF strands under varying field and temperature, Note AIM/NTT-2001.031

L. Zani, H. Cloez, Z. Bej, J.P. Serriesand E. Mossang

M50 Task M50: Manufacture of two subsize NbTi joint sample.Note AIM/NTT/2001.028

P. Decool, H. Cloez

M50 Task M50: Deliverable 5, Report on design of full size conductor samples.Note AIM/NTT/2001.027

P. Decool

TW0-T400-1 Model of heat deposition during fast discharge tests of the ITER toroidal field model coil. Presented at the 17 th International Conference on Magnet Technology, Geneva September 2001.

P. Hertout, A. Bleyer, J.L Duchateau, A. Martinez and S. Nicollet.

TW0-T400-1 Resistances of electrical joints in the TF model coil of ITER: comparisons of first test results with samples results. Presented at the 17 th International. Conference on Magnet Technology, Geneva September 2001.

D. Ciazynski et al.

TW1-TMC-SCABLE Critical properties of ITER PF strands under varying field and temperature. Note AIM/NTT-2001.031

L. Zani, H. Cloez, Z. Bej, J.P. Serries and E. Mossang


Breeding Blanket

Water Cooled Lithium Lead (WCLL) Blanket

TTBA-2.1 Definition of specifications for a demonstrator of the WCLL test blanket module for ITER-FEAT. CEA report SERMA/LCA/RT/01-2916, Sept. 2001.

Y. Poitevin et al.

TTBA-2.2 Solid HIP demonstrator for fabrication and coating, fabrication of double wall tubes. CEA report, to be issued.

E. Rigal, P. Bucci, C. Grandjacques

TTBA-3.5 Tritium permeation from Pb-17Li towards water. to be issued T. Dufrenoy, V. Lorentz, O. Raquet,A. Terlain

TW1-TTBA-001-D01 Status of the design and testing programme of the WCLL test blanket module for ITER-FEAT. CEA internal report SERMA/RT/01-3019/A, December 2001.

Y. Poitevin et al.

TW1-TTBA-001-D01 Fabrication sequence of the WCLL test blanket module for ITER-FEAT. CEA internal report SERMA/RT/01-3020/A, January 2002.

Y. Poitevin et al.

TW1-TTBA-001-D01 WCLL blanket concept: synthesis of last R&D results and impact on the test blanket module design. CEA internal report, SERMA/RT/02-3061, March 2002.

Y. Poitevin et al.

TW1-TTBA-001-D04 Modelling of a heat exchanger Water/Li-17Pb in normal and accidental situation CEA report DER/DTP/STH/LTA/2001-30 December 2001

G. Avakian

TW1-TTBA-002-D01 WCLL test blanket module demonstrator: development programme and specifications. CEA Report, DM2S/SERMA/LCA/RT/01-3024/A (2001).

A. Li Puma et al.

TW1-TTBA-002-D02 CEA report Note technique DTEN 03/2002, 4/01/02 E. Rigal, P. Le Gallo, C.

TW1-TTBA-002-D03 DIADEMO experimental program – Results of U bent DWT tests on Pb-Li. NT DER/STR/LCET 01-065.

L. Cachon et al

- 483 -

TW1-TTBA-002-D05 EFDA TW1-TTBA-2.5 Blanket manufacturing techniques integrated mixed-powder HIP fabrication route for TBM with DWT. Note Technique DEM n°30/2002.

P. Bucci , L. Bedel, J. Calapez,C. Grangjacques, J.M. Leibold

TW1-TTBA-004-D03 ITER FEAT : couverture tritigène. Considérations sur une instrumentation interne. NT SCCD 2001-060

J.P. Trapp, Ch. Blandin

TW1-TTBA-005-D03 Safety of the WCLL blanket module system: impact of the ITER specifications and integration of the R&D. CEA Report, SERMA/LCA/RT/01-3023

A. Li Puma, Y. Poitevin

TW1-TTBA-006-D02 Natural convection under intense magnetic field in vertical enclosures.NT DER/STR/LCET 01-083

G. Authier et al

TW1-TTBA-006-D02 Convection naturelle sous champs magnétique en cavité verticale élancée. Application aux couvertures des réacteurs de fusion. Thèse de l’Institut National Polytechnique de Grenoble soutenue de 28 Mars 2002.

G. Authier

Helium Cooled Pebble Bed (HCPB) Blanket

TTBB-2.3 Second bent HCPB first wall mock up manufactured by improved HIP forming technique. CEA Report Note technique DTEN no. 61/2001, 27 june 2001.

E. Rigal, C. Grandjacques, F. Bruchon

TW1-TTBB-002-D02 HCPB First wall mock up manufactured with an alternative reduced cost fabrication technique. CEA Report, to be issued.

E. Rigal, C. Grandjacques, F. Bruchon

TW1-TTBB-005-D03 Interim report of the activity on the optimization of the fabrication process of Li2TiO3 pebbles. Internal report CEA/SE2M/LECMA 01-DT-011. June 2001.

J.D. Lulewicz

TW1-TTBB-005-D03 Annual report on sub-task TTBB-005-3 and sub-task TTBB-005-4.Internal report CEA/SE2M/LECMA 01-DT-025. November 2001.

J.D. Lulewicz

TW1-TTBB-005-D03 Thermal creep of metatitanate pebble beds. Presented at CBBI-10, Karlsruhe (Germany), October 2001.

J. Reimann, J.D. Lulewicz, N . Roux, G. Worner.

TW1-TTBB-005-D03 The fabrication of Li2TiO3 pebbles by extrusion-spheronisation-sintering, a

suitable process for tailoring pebbles properties. Presented at ICFRM-10, Baden-Baden (Germany), October 2001.

J.D. Lulewicz, N. Roux

TW1-TTBB-005-D03 Status of fabrication of Li2TiO3 pebbles by extrusion-spheronisation-sintering

process. Presented at CBBI-10, Karlsruhe (Germany), October 2001.

J.D. Lulewicz, N. Roux, F. Pourchet, J.P. Joulin

TW1-TTBB-005-D04 Interim report of the activity on the optimisation of the fabrication process of Li2TiO3 pebbles. Internal report CEA/SE2M/LECMA 01-DT-011. June 2001.

J.D. Lulewicz

TW1-TTBB-005-D04 Annual report on sub-task TTBB-005-3 and sub-task TTBB-005-4.Internal report CEA/SE2M/LECMA 01-DT-025. November 2001.

J.D. Lulewicz

TW1-TTBB-005-D04 Thermal creep of metatitanate pebble beds. Presented at CBBI-10, Karlsruhe (Germany), October 2001.

J. Reimann, J.D. Lulewicz, N . Roux, G. Worner

TW1-TTBB-005-D04 The fabrication of Li2TiO3 pebbles by extrusion-spheronisation-sintering, a

suitable process for tailoring pebbles properties. Presented at ICFRM-10, Baden-Baden (Germany), October 2001.

J.D. Lulewicz, N. Roux

TW1-TTBB-005-D04 Status of fabrication of Li2TiO3 pebbles by extrusion-spheronisation-sintering

process. Presented at CBBI-10, Karlsruhe (Germany), October 2001.

J.D. Lulewicz, N. Roux, F. Pourchet, J.P. Joulin

Structural Materials development

Advanced Materials

TW1-TTMA-001-D01 TTMA 1.2 – SiC-SiC composite development and characterization.Note technique DTEN n° 2001/130, 12/12/2001

R. Couturier, B. Riccetti, Y. Dextre, M. Petit

- 484 -

Reduced Activation Ferritic Martensitic (RAFM) Steels

TW1-TTMS-001-D02 Status of CEA irradiation experiment performed in BOR 60 reactor.N.T. SRMA 02-2464, March 02.

A. Alamo, J.L. Bertin

TW1-TTMS-002-D03 Metallurgical characterization of as-received Eurofer97 products. CEA report, NT SRMA 01-2418, March 2001.

C.A. Danon, S. Urvoy, A. Alamo

TW1-TTMS-002-D03 Phase transformation behaviour of Eurofer 97 under continuous cooling. communication ICFRM10, to be published in JNM.

C.A. Danon, A. Alamo

TW1-TTMS-002-D03 Phase transformation behaviour of Eurofer 97 upon heating and cooling.CEA report, NT SRMA 02-2459, January 2001.

C.A. Danon, A. Alamo

TW1-TTMS-002-D04 Mechanical properties of EUROFER 97 steel in the as-received condition.CEA report NT SRMA 01-2419, April 2001.

A. Alamo, P. Wident, Y. Tournier,S. Urvoy

TW1-TTMS-002-D04 Effect of thermal ageing at 650-700°C on the mechanical properties of Eurofer 97 steel. CEA report NT SRMA 02-2470, Mars 02.

A. Bougault, S. Urvoy, P. Wident,A. Alamo

TW1-TTMS-002-D16 Mechanical properties of A RAFM/RAFM HIP Joint (2001). TTMS 2-16. Note Technique DTEN

L. Bedel, J. Calapez, P. Lemoine,B. Riccetti

TW1-TTMS-002-D18 Mechanical properties of Eurofer HIP'ed powder material -Task TTMS-2.18. Note technique D.T.E.N. N° 134/2001

J.M. Gentzbittel, I. Chu, P. Lemoine

TW1-TTMS-004-D02 Eurofer Powder HIP development and characterization. Task TTMS-4.2Note technique D.T.E.N. N° 135/2001

J.M. Gentzbittel, I. Chu, E. Rath

TW1-TTMS-004-D02 The effect of High Isostatic Pressing parameters on microstructure and mechanical properties of Eurofer powder HIP'ed material. ICFRM10 Baden Baden- 14-19 /10/2001

J.M. Gentzbittel, I. Chu, H.Burlet

TW1-TTMS-004-D04 TIG weldability of F82H with matching filler metal. CEA report n°DECS/STA/LMS/01-RT4005, October 2001

A. Fontes

TW1-TTMS-004-D05 Filler material for the TIG welding of RAFM/316LN transition joints.CEA report n°DECS/STA/LMS/01-RT4008, December 2001

A. Fontes

TW1-TTMS-004-D06 Solid HIP process qualification, application to complex shapes. subtask TTMS4.6, CEA Report Note technique DTEN no. 22/2002, 7 march 2002.

E. Rigal, F. Bruchon

TW1-TTMS-005-D02 Appendix A. Material Design Limit Data, A3.S18F, F82H Steel. Draft Interim SM 5.1 & 5.4 Report, NT DECM/Dir, Dec. 2001.

TW1-TTMS-005-D02 Development and the database of a reduced activation martensitic steel F82H for fusion reactors. paper 11A.O.I.1 and poster 04.PO.07, ICFRM-10, 14-19 Oct. 2001, Baden-Baden, Germany.

TW1-TTMS-005-D02 Recent limits and improvements of structural materials for fusion reactors presented at ICFRM-10, to be published independently as a review paper in the JNM, 2002.

TW1-TTMS-005-D02 Materials design data for reduced activation F/M steel type F82H. to be presented at ISFNT-6.

TW1-TTMS-006-D01 Development of the elaboration process and joining technologies of RAFM ODS steels. Fusion Engineering and Design 58-59 (2001) 761 - 765.

S. Revol, S. Launois, B. Baccino,G. Le Marois, E. Rigal

TW1-TTMS-006-D01 Task TTMS6.1: Qualification of high performance ODS steels. CEA report NT DTEN N°128/2001, Dec. 2001.

C. Cayron, I. Chu, S. Launois,S. Revol

TW1-TTMS-006-D03 Metallurgical and mechanical characterization of ODS variants based on Eurofer steel. CEA report, NT SRMA 02-2466, March 2002.

A. Alamo, S. Urvoy

Neutron Source

TTMI-001 CEA-DSM-DAPNIA-SEA contribution to the IFMIF KEP phaseStep report – June 2001, DSM/DAPNIA/SACM 01/41

TTMI-001 CEA-DSM-DAPNIA-SEA contribution to the IFMIF KEP phaseStep report – June to December 2001, DSM/DAPNIA/SACM 02/09

- 485 -


SEA5-1 Report on ITER 01 and ITER 02 tests in the CORELE 2 loopTechnical Note DEC/S3C/01-139 revision 1

T. Duverneix, V. Biscay

SEA5-2 ISAS final activity report for 2001CEA report SFME/LGLS/RT/01-019/A, October 2001

Th. Boubee de Gramont

TSW-2.1 Waste management of a future fusion power plantTask TSW-002, Note Technique STR/LCEP 2001/001.

S. Rosanvallon

TSW-2.1 Steel detritiation by melting with gas bubbling paper presented at the 6th International Conference on Tritium Science and Technology, Tsukuba, Japan, November 11-16, 2001.

S. Rosanvallon, J.L. Courouau,G. Marbach, W. Gulden

TSW-2.6 Waste management of a future fusion power plantTask TSW-002 deliverable 6, Note Technique STR/LCEP 2001/001.

S. Rosanvallon


Cat V accident analysis with PAX2 code: H2 production via delayed plasma

shutdown TA – 256499

TW0-SEA4SEA4-4

NEW INTEGRATED ICE LOVA FACILITY : 3rd set of pre and post calculation (October 2001). TA-236840 A

System Studies

Power Plant Conceptual Studies (PPCS)

TW0-TRP-3D1 Analysis of containment options for PPCS model A WCLL,CEA report DER/SERI/LFEA 02/50XX, to be issued

TW0-TRP-4D5 Thermo-mechanical evaluation of the WCLL blanket concept (MODEL A) - NT/SERI/LFEA/02-50XX (to be published)

B. Michel

TW1-TRP-PPCS1-D04 PPCS model A (WCLL) - Data for the safety evaluation, CEA report , DER/SERI/LFEA 02/50XX, to be issued

TW1-TRP-PPCS3-D01 Comparison of different self-cooled SiCf/SiC blanket and divertor concepts CEA report DEN/DM2S/SERMA/LCA/RT/01-3022, December 2001.

H. Golfier, et al.

Socio-Economics Studies

TW1-TRE-ECFA-D01 External costs of Fusion: a comparison with advanced fission technologies - CEPN-NTE/01/26, December 2001.

L. Vaillant

JET Technology

JW0-FT-2.5 Dedicated procedures for carbon compounds and stainless steelstask JWO-FT-2.5, NT CEA STR/LCEP 2001/085

S. Rosanvallon

UNDERLYING TECHNOLOGY PROGRAMME

Physics Integration

Diagnostics

UT-PE-HFW Study of thermo mechanical properties of Y2O3 material

Report CEA/DRT/DECS/SE2M/LECMA 01-DT-13 – 25/06/2001

N. Lochet

UT-PE-HFW Study of thermo mechanical properties of Y2O3 material

Report CEA/DRT/DECS/SE2M/LECMA 01-DT-027 – 19/11/2001

N. Lochet

- 486 -

Vessel/In Vessel


UT-PFC&C-HIP Mechanical behaviour of HIP jointsNT SRMA 02-2480

A. Fissolo

UT-VIV/PFC-BDG Boron – doped graphites. Mechanical and thermal characterization, January – June 2001 report. CEA/DRT/DECS/SE2M/LECMA 01-DT-14 - 27/06/2001

N. Lochet

UT-VIV/PFC-BDG Boron – doped graphites. Mechanical and thermal characterizationFinal report CEA/DRT/DECS/SE2M/LECMA 01-DT-26 – 15/11/2001

N. Lochet

UT-VIV/PFC-SIC/MJ UT-PFC&C-SiC/MJ, Development of SiC/metal joining technology, complement to the 2nd progress report. Note Technique DTEN n°121/2001.

F. Saint-Antonin

UT-VIV/PFC-SIC/MJ UT-PFC&C-SiC/MJ, Development of SiC/metal joining technology, 3rd progress report. Note Technique DTEN n°25/2002.

G. Delette

UT-VIV/PFC-TMM Progress in the design and construction of a thermal fatigue experimental set-up. CEA report DM2S SEMT/LISN/RT/02-009/A (February, 8, 2002)

Ph. Matheron

UT-VIV/PFC-TMM Failure criteria for carbon fiber reinforced carbon composite (CFC)CEA report DM2S to be published

C. Guerin

UT-VIV/PFC-TMM Integrity evaluation of a CFC tile under thermo-mechanical loading – A finite element calculation using CAST3M. CEA report DM2S to be published

C. Guerin

Remote Handling

UT-VIV/AM-Actuators Detailed design of the prototype actuatorCEA/DTSI/SRSI/LPR/01RT.029/ Issue.0

UT-VIV/AM-Actuators Test of a clamping module made of thermal actuatorsCEA/DTSI/SRSI/LPR/02RT.001/ Issue.0

UT-VIV/AM-ECIr Test de composants électroniques sous irradiation jusqu’à 1MGyCEA Report DTR/LIST/DTSI/SLA/01-368

J.M. Armani, C. Brisset

UT-VIV/AM-HMI Review of feasibility of coupling graphical simulation to real-time computing and evaluation of dose rate. Choice of numerical methods.CEA/DTSI/SRSI/LCI/01RT.036/ Issue 0

L. Chodorge

UT-VIV/AM-HMI Development of a mock-up for radiative point-like sourcesCEA/DTSI/SRSI/LCI/02RT.002/ Issue 0

L. Chodorge

UT-VIV/AM-Hydro IN-LHC Servovalve 1900687 Spécification d'une servovalve pression 4 voies - STR/00RT.024 -28 septembre 2000

F. Louveau

UT-VIV/AM-Hydro Design and launch manufacture of the pressure valvesDPSA/STR/LTO/00RT.096 Rev 0. –5 jan 2001

F. Louveau

UT-VIV/AM-Hydro Results on qualification of a pressure servo-valve for force feedback applications. DTSI/SRSI/LPR/01RT.043

Y. Measson, O. David

UT-VIV/AM-Hydro Qualification of a Maestro arm equipped with pressure servo-valvesDTSI/SRSI/LPR/02RT.008

Y. Measson, O. David


Breeding Blanket

UT-TBM/BB-IMBLA Water Cooled Pb-17Li DEMO Blanket. A thermo-mechanical study using CASTEM 2000. Structural integrity verification and lifetime determinationCEA Report, DM2S/SEMT/LM2S/RT/02-009

C. Guerin et al.

UT-TBM/BB-IMBLA High performances for TAURO blanket systemCEA Report DM2S/SERMA/LCA/RT/01-3021/A.

H. Golfier, at al

UT-TBM/BB-IMBLA Potential and limits of WCLL alternative blanket conceptsCEA Report, DM2S/SERMA/LCA/RT/01-3026/A.

A. Li Puma et al.

- 487 -

UT-TBM/MAT-LM/MAG Corrosion study of an austenitic steel in Pb-17Li under magnetic field and rotating flow. CEA report, RTSCCME 587 (December 2001)

Ph. Deloffre, A. Terlain, A. Alemany, A. Kharicha

UT-TBM/MAT-LM/refrac Corrosion of tungsten by Pb-17LiRapport CEA RT-SCCME 595 (December 2001)

T. Dufrenoy, V. Lorentz, F. Herbert,A. Terlain

UT-TBM/MAT-LM/SiC Compatibility of SiCf/SiC composite with liquid Pb-17Li alloy at high temperature. RT-SCCME 586 (Décembre 2001)

Ph. Deloffre, A. Terlain, T. Dufrenoy, F. Herbert, V. Lorentz

UT-TBM/MAT-LM/SiC Compatibility with Pb-17Li of material for fusion reactor10th International Conference on Fusion Reactor Materials, 14-19 October 2001, Baden-Baden, Germany

Ph. Deloffre, A. Terlain, F. Herbert ,F. Barbier

UT-TBM/MAT-LM/WET Wetting of tungsten by Pb and Pb-17LiCEA Report, RT SCCME 588 (December 2001)

P. Protsenko, M. Jeymond,N. Eustathopoulos, A. Terlain

Materials Development

Structural Materials

UT-SM&C-COR Revised E-pH diagrams of the iron-H2O system as a function of temperature

RT-SCCME 600 (March 2002)

J. Chivot

UT-TBM/MAT-BIM Optimisation of the spatial resolution of a digital image correlation. Application on Eurofer-316LN and CuCrZr-316LN junctionsUT-SM&C-BIM Note Technique DTEN N° 2001/133

L. Bedel, I. Chu, Y. Dextre,B. Riccetti

UT-TBM/MAT-LAM/MIC Microstructure et dureté de la martensite dans les aciersNote Technique D.E.M. N°2000/71, septembre 2000.

J. Laurencin

UT-TBM/MAT-LAM/MIC Analyse morphologique et cristallographique de la structure martensitique dans l’acier Eurofer. Progress Report UT-SM&C-LAM/Mic, CEA report, NT SRMA 00-2400, décembre 2000.

Y. de Carlan, L. Guetaz

UT-TBM/MAT-LAM/MIC Mécanismes de déformation de l’acier martensitique EUROFERCEA Report, Note technique DTEN N° 2002/20, fevrier 2002.

L. Guétaz, Y. de Carlan, F. Barcelo, J-P. Millier, S. Urvoy, P. Wident

UT-TBM/MAT-LAM3 Microstructural evolution of reduced activation and conventional martensitic steels after thermal ageing and neutron irradiationProgress Report UT-SM&C-LAM3, CEA report, NT SRMA 00-2396, décembre 2000.

M.H. Mathon, Y. de Carlan,G. Geoffroy, X. Averty,C.H. de Novion and A. Alamo

UT-TBM/MAT-LAM3 SANS study of the microstructural evolution of reduced activation and conventional martensitic steels under neutron irradiationProgress Report Contract UT-TBM/MAT-LAM3, CEA report, NT LLB 2002-03, février 2002.

Mathon M. H., de Carlan Y., Geoffroy G., Averty X., de Novion C. H. and Alamo A.

UT-TBM/MAT-ODS UT-SM&C-ODS : Development of forming and joining technologies for ODS steels. CEA report NT DEM N°79/99, nov. 1999.

S. Revol, C. Labonne

UT-TBM/MAT-ODS UT-SM&C-ODS : Development of forming and joining technologies for ODS steels. CEA report NT DEM N°117/2000, dec. 2000.

S. Launois, S. Revol, C. Labonne

UT-TBM/MAT-ODS UT-SM&C-ODS: Development of forming and joining technologies for ODS steels. CEA report NT DTEN N°129/2001, Dec. 2001.

C. Cayron, I. Chu, S. Launois,S. Revol

Fuel Cycle

UT-TBM/FC-SP Superpermeation at the low energy ion bombardment: nonmonotonous energy dependence. Rapport N°1 du Contract CEA/Cadarache No. V.3094.002. avt 3, 2001, Juin, Report LPTP 4016.

A.I. Livshits, V.N. Alimov,A.M. Bruneteau, M. Bacal

UT-TBM/FC-SP Effect of niobium membrane carbidization on its superpermeationRapport No. 2 du Contract CEA/Cadarache No.V.3094.002. avt 3, 2001, December, Report LPTP 4055.

M.E. Notkine, V.N. Alimov,A.M. Bruneteau, M.Bacal

UT-TBM/FC-SP Effect of oxygen on plasma driven superpermeation of hydrogen through a niobium membrane under ion bombardmentAnnotations of presentations at the International Workshop "Interaction of hydrogen isotopes with structural materials, IHISM-01", (Sarov, April 2-6, 2001), RFNC-VNIIEF, 2001, p. 36 - 39.

M.E. Notkin, A.I. Livshits, M. Bacal

- 488 -

UT-TBM/FC-SP Effect of ion bombardment on plasma-driven superpermeation of hydrogen isotopes through a niobium membrane - Nucl. Instr. and Meth. B,179 (2001) 373-382.

M.E. Notkin, A.I. Livshits, A.M. Bruneteau, M. Bacal

UT-TBM/FC-SP Correlation between Balmer a emission and hydrogen flux through a superpermeable niobium membrane in a low pressure multicusp plasma source. Nucl. Instr. and Meth. B, to be published.

A.M. Bruneteau, M.E. Notkin,A.I. Livshits and M. Bacal


UT-S&E-Mitig Modifications of the CIGNE facility for hydrogen mitigation experimentsNT DER/STR/LCEP/2001/003

C. Maruejouls

UT-S&E-Mitig Operating rules for the CIGNE facilityNT DER/STR/LCEP/2002/002

C. Maruejouls

UT-S&E-BLK Spécification techniques pour la mise en place d’un électroaimant pour le programme DIADEMO-MHD, NT DER/STR/LCET 01-075

F. Garnero et al

UT-S&E-BLK Conception d’un pot d’essai en Pb-Li pour une expérimentation MHDNT DER/STR/LCET 01-082.

C. Roche et al

UT-S&E-BLK Electro- magnet calibration, to be edited. L. Cachon et al

System Studies

UT-SS-REL Double walled tube concept impact on the pressure tubes reliability/availability - Rapport DEN/DM2S, SERMA/LCA/RT-012999/A

Li Puma A., Eid M.Y.

INERTIAL CONFINEMENT FUSION PROGRAMME

ICF01 Nonlinear propagation of short intense laser pulses in a hollow metallic waveguide Phys. Rev. E 64, 016404 (2001)

N.E. Andreev, C. Courtois, B. Cros, L.M. Gorbunov, G. Matthieussent

ICF01 Propagation of intense ultra-short laser pulses in a plasma filled capillary tube: simulations and experiments. Phys. Plasma 8, 3445 (2001)

C. Courtois, A. Couairon, B. Cros, J.R. Marquès, G. Matthieussent

ICF01 Long range 2-correlated stopping of relativistic electrons in ultradense plasmas. Nucl. Instrum. Meth. Phys. Res. A464, 243 (2001)

C. Deutsch and P. Fromy

ICF01 Collective vs particle stopping in the FIS. GSI report 04*01, 63 (2001) C. Deutsch, P. Fromy, C. Toupin and G. Bonnaud

ICF01 Accelerator system and final beam transport in heavy ion inertial confinement fusion. J. Plasma and Fusion Research, 77, 33 (2001)

C. Deutsch, S. Kawataand T. Nakamura

ICF01 Intense ion beam propagation in reactor sized chamber Nucl. Instrum. Meth. Phys. Res. A464, 293 (2001)

J. L. Vay and C.Deutsch

ICF01 Modeling of swift heavy ions interaction with dense matterNucl. Instrum. Meth. Phys. Res. A 464, 86 (2001)

G. Maynard, K. Katsonis, C. Deutsch, G. Zwicknagel, M. Chabotand D. Gardès

ICF01 Experimental analysis of the stopping cross sections and of the charge changing processes for Clq+ projectiles at the maximum of the stopping power.Nucl. Instrum. Meth. Phys. Res. A 464, 253 (2001)

D.Gardès, M.Chabot, M.Nectoux, G.Maynard, C.Deutsch et G.Belyaev

ICF01 Diffusion transport cross section and stopping power of swift heavy ionsPhys. Rev. A 63, 52903 (2001)

G. Maynard, G. Zwicknagel,C. Deutsch et K. Katsonis

ICF02 Magnetic levitation for IFE targets production. Part I and IITask ICF 02. Note SBT/CT 2000-58 (jan 2001)

D. Chatain

- 489 -

ICF03 Spectroscopy of MeV - Ion jets from ultraintense laser-plasma interaction with thin foils

M. Hegelich, S. Karsch, M. Allen,P. Audebert, A. Blasevicz, T. Cowan,J. Fuchs, J.C. Gauthier, W. Guenther,M. Geissel, D. Habs, W. Heinrich,J. Meyer-ter-Vehn, G. Pretzler,A. Pukhov, T. Schlegel, K. Witte andM. Roth, to be submitted to PRL

ICF03 The dependence of intense laser-accelerated ion beams on target properties M. Roth, T.E. Cowan, J. C. Gauthier,M. Allen, P. Audebert, A. Blazevic,J. Fuchs, M. Geissel, M. Hegelich,S. Karsch, J. Meyer-ter Vehn,A. Pukhov, T. Schlegel, submitted to PRE

ICF03 Acceleration of laser driven MeV-Ion jets from thin foil targetsInvited talk at the 2nd International Conference on Inertial Fusion Sciences and Applications, Kyoto, Sept. 9-14, 2001.

M. Hegelich, S. Karsch, M. Allen,P. Audebert, A. Blasevicz, T. Cowan,J. Fuchs, J.C. Gauthier, W. Guenther,M. Geissel, D. Habs, W. Heinrich,J. Meyer-ter-Vehn, G. Pretzler,A. Pukhov, T. Schlegel, K. Witteand M. Roth

ICF03 Intense ion beams accelerated by relativistic laser plasmasInvited talk at SPIE Conference, San Diego (August 2001, to be published)

J. C. Gauthier, M. Roth, T.E. Cowan,M. Allen, P. Audebert, A. Blazevic,J. Fuchs, M. Geissel, M. Hegelich,S. Karsch, J. Meyer-ter Vehn,A. Pukhov

ICF04 Spectroscopy of MeV - Ion jets from ultraintense laser-plasma interaction with thin foils

M. Hegelich, S. Karsch, M. Allen,P. Audebert, A. Blasevicz, T. Cowan,J. Fuchs, J.C. Gauthier, W. Guenther,M. Geissel, D. Habs, W. Heinrich,J. Meyer-ter-Vehn, G. Pretzler,A. Pukhov, T. Schlegel, K. Witteand M. Roth, submitted to PRL

ICF04 Intense ion beams accelerated by relativistic laser plasmasInvited talk at SPIE Conference, San Diego (August 2001, to be published)

J. C. Gauthier, M. Roth, T.E. Cowan,M. Allen, P. Audebert, A. Blazevic,J. Fuchs, M. Geissel, M. Hegelich,S. Karsch, J. Meyer-ter Vehn,A. Pukhov

ICF-KIT-PRC A comparative assessment of the state of progress in inertial fusion power reactor conceptual designsCEA technical note, SERMA/LCA/RT/01-2998/A

M.Y. Eid

- 490 -

- 491 -

Task Title Prog. Field Area Unit Site Task Leader Page

CEFDA00-517 Design of cryogenic transfer lines and ring manifolds for ITER-FEAT EFDA M Cryo DRFMC Grenoble Millet F. 143

CEFDA00-524Study to optimise intersector welding robot (IWR) design and machining characteristics

EFDA VIV RH GAER Cassis Meja P. 115

CEFDA00-541Magnet design on PF and correction coils : conceptual design and analysis

EFDA M Cryo DRFC Cadarache Duchateau J.L. 147

CEFDA00-543High heat flux testing and analysis of small scale mock-ups - Part 2 : Analysis

EFDA VIV PFC DM2S Saclay Salavy J.F. 43

CEFDA00-546Support to ITER ICRF system physics and engineering design - Electrical design of an ICRF array for high RF power density in ITER-FEAT

EFDA PI Hea DRFC Cadarache Brémond S. 15

CEFDA00-553 Support to ITER-FEAT lower hybrid launcher and transmission line EFDA PI Hea DRFC Cadarache Bibet Ph. 11

CEFDA00-556 Simulation of ultrasonic inspection process EFDA VIV V/B DECS Saclay Mahaut S. 67

CEFDA00-561 Support to ITER diagnostic design : polarimetry EFDA PI Diag DRFC Cadarache Gil C. 5

CEFDA00-565Improvement evaluation for infrared detection of PFC defects - SATIR upgrading

EFDA VIV PFC DRFC Cadarache Durocher A. 47

CEFDA00-566 Layout of the cryoplant for RTO/RC ITER EFDA M Mag DRFMC Grenoble Millet F. 145

CEFDA00-569Development of vacuum coaxial capacitors for the ITER-like ICRF JET antenna


CEFDA01-581Critical heat flux testing of hypervapotrons - 200 kW electron beam gun test

EFDA VIV PFC DRFC Cadarache Escourbiac F. 51

CEFDA01-587 Study to evaluate ITER proposals for VV code use EFDA VIV V/B DM2S Saclay Devos J. 71

CNET98-480Thermal fatigue testing of divertor full scale prototypes - 200 kW electron beam gun test


CNET98-485Thermal fatigue testing of baffle full scale prototype - 200 kW electron beam gun test


DV4.3Optimisation and manufacture of high heat flux components - Study of flat tile cascade failure possibility for high heat flux components

EFDA VIV PFC DRFC Cadarache Schlosser J. 53

ICF01 Intense laser and particle beams dynamics for I.C.F. applications ICF ICF ICF Université Orsay Deutsch C. 453

ICF02 Cryogenic targets production using magnetic levitation ICF ICF ICF DRFMC Grenoble Chatain D. 457

ICF03 Laser-matter interaction at relativistic intensities and fast igniter studies ICF ICF ICF EP-LULI Palaiseau Migus A. 461

ICF04 European collaborative experiment on the fast igniter concept ICF ICF ICF EP-LULI Palaiseau Migus A. 463

ICF-KiT-PRC Overview on power reactor concepts ICF ICF ICF DM2S Saclay Eid M. 465

JET-EP-Div The JET EP divertor project EFDA JET JET DRFC Cadarache Chappuis Ph. 343

JW0-FT-2.5Tritium processes and waste management - Dedicated procedures for the detritiation of selected materials

EFDA JET JET DER Cadarache Rosanvallon S. 347

M40 Design work on magnet R&D EFDA M Mag DRFC Cadarache Libeyre P. 153

M50 Conductor R&D - Development of NbTi conductors for ITER PF coils EFDA M Mag DRFC Cadarache Decool P. 157

SEA5-1 Validation of computer codes and models EFDA S&E Safety DEC Cadarache Tarabelli 295

SEA5-2Coherent system of codes for the ITER safety analysis - Validation of computer codes and models

EFDA S&E Safety DM2S Saclay Toumi I. 299

SM-2-3-1 Mechanical properties of F82H weldments EFDA TBM RAFM DECS Saclay Fontes A. 263

SM-3-3 Corrosion in water conditions (EUROFER 97 and F82H ) EFDA TBM RAFM DPC Saclay Raquet O. 253

T216-GB8 Small scale testing of first wall/shield modules EFDA VIV V/B DTEN Grenoble Saint-Antonin F. 91

APPENDIX 4 : CEA TASKS IN ALPHABETICAL ORDER

- 492 -


T252Radiation tolerance assessment of standard components for remote handling and process instrumentation

EFDA VIV RH DTSI Fontenay Giraud A. 119

T329-5 In-vessel RH dexterous operations - Task extension 2 EFDA VIV RH DTSI Fontenay Gravez P. 125

TSW-2.1Waste and decommissioning strategy - Improvement to an existing facility and possibilities for diminishing gas release

EFDA S&E Safety DER Cadarache Rosanvallon S. 301

TSW-2.6Waste and decommissioning strategy - Requirements of decommissioning and waste management strategies

EFDA S&E Safety DER Cadarache Rosanvallon S. 303

TTBA-2.1Blanket manufacturing techniques - Definition of specifications for demonstrators

EFDA TBM WCLL DM2S Saclay Poitevin Y. 179

TTBA-2.2Blanket manufacturing techniques - Solid HIP demonstrator for fabrication and coating, fabrication of double wall tubes

EFDA TBM WCLL DTEN Grenoble Rigal E. 183

TTBA-3.5 Coating qualification and irradiation tests - Permeation out-of-pile testing EFDA TBM WCLL DPC Saclay A. Terlain 197

TTBB-2.3Blanket manufacturing techniques - First wall manufacturing by HIP forming technique

EFDA TBM HCPB DTEN Grenoble Rigal E. 217

TTMI-001 IFMIF - Accelerator facility EFDA TBM NS DAPNIA Saclay Ferdinand R. 291

TTMS-2.3.2 Mechanical properties of EUROFER 97 weldments EFDA TBM RAFM DECS Saclay Fontes A. 265

TW0-DIAG-DEV ITER diagnostic window development EFDA PI Diag DRFC Cadarache Lippa M. 7

TW0-DTP/1.1TW1-TVA-BTS

Carrier and bore tools for 4" bent pipes EFDA VIV RH DTSI Fontenay Friconneau J.P. 129

TW0-DTP/1.2&4TW1-TVA-IVP

Prototypical manipulator for access through IVVS penetrations (IVP) EFDA VIV RH DTSI Fontenay Friconneau J.P. 133

TW0-DV4/01Optimisation of manufacture of high heat flux components : tungsten monoblocks

EFDA VIV PFC DTEN Grenoble Rigal E. 55

TW0-ICRF/ANTICRF Antenna and vacuum transmission line development - ICRH Antenna coupling : near field computations part II

EFDA PI Hea Unancy Nancy Heuraux S. 23

TW0-LASER/CUTVV intersector maintenance - Further development of high power Nd YAG laser cutting - Improvement of YAG laser backplate cutting by adding powder

EFDA VIV V/B DECS Saclay Alfillé J.P. 73

TW0-LASER/HYDYAG laser process for cutting and welding of the blanket module hydraulic connections

EFDA VIV V/B DECS Saclay Alfillé J.P. 77

TW0-LASER/REWELDVV intersector maintenance - Further development of high power Nd - YAG laser rewelding after cutting

EFDA VIV V/B DECS Saclay Aubert P. 81

TW0-LASER/WELDVV intersector joining - Further development of high power Nd - YAG laser welding with multipass filler wire

EFDA VIV V/B DECS Saclay Aubert P. 85

TW0-NB.DEV.1Neutral beam development for EDA extension - EU-JA collaborative experiment on KAMABOKO source

EFDA PI Hea DRFC Cadarache Boilson D. 31

TW0-SEA4SEA4-4

In-vessel safety - Third set of pre and post calculation of in-vessel LOCA’s on the new japanese “ICE” facility

EFDA S&E Safety DER + TA Cadarache Sardain P. 307

TW0-T400-1 CMSC and TFMC installation and test EFDA M Mag DRFC Cadarache Libeyre P. 159

TW0-T420/06 Fabrication of a first wall panel with HIP’ed beryllium armor EFDA VIV V/B DTEN Grenoble Bucci. Ph. 93

TW0-T420/08 Development of HIP fabrication technique EFDA VIV V/B DTEN Grenoble Bucci. Ph. 99

TW0-T438-01 Development and testing of time resolved erosion detecting techniques EFDA VIV PFC DRFC Cadarache Gauthier E. 59

TW0-T508/04 Development of Be/CuCrZr HIPping technique EFDA VIV V/B DTEN Grenoble Saint-Antonin F. 103

TW0-T508/05 Development of Be/CuCrCz brazing technique EFDA VIV V/B DTEN Grenoble Saint-Antonin F. 105

TW0-TRP-3D1 Analyze the sensitivity of achieving accident management EFDA SS PPCS DER Cadarache Sardain P. 319

TW0-TRP-4D5 In-vessel components EFDA SS PPCS DER Cadarache Michel B. 321

TW1-TMC-CODES Design and interpretation codes EFDA M Mag DRFC Cadarache Martinez A. 163

TW1-TMC-SCABLE Cable and conductor characterization EFDA M Mag DRFC Cadarache Zani L. 167

TW1-TPH-ICRANTICRF Antenna and vacuum transmission line development - Design & manufacturing of a CW ICRF high power test rig and testing of next step antenna prototype components


- 493 -


TW1-TRE-ECFA-D01Externalities of fusion - Comparison of fusion external costs with advanced nuclear fission reactor

EFDA SS SERF CEPN Fontenay Schneider Th. 335

TW1-TRE-ECFA-D02Externalities of fusion accident - Sensitivity analysis on plant model and site location

EFDA SS SERF CEPN Fontenay Schneider Th. 339

TW1-TRP-PPCS1-D04 Model A (WCLL) - Consistency with the PPCS GDRD EFDA SS PPCS DER Cadarache Sardain P. 325

TW1-TRP-PPCS1-D10 Model A (WCLL) - Design integration EFDA SS PPCS DER Cadarache Sardain P. 327

TW1-TRP-PPCS3-D01Selection of advanced models - Assessment of Pb-17Li cooled blanket and divertor concepts using SiCf/SiC as structural material

EFDA SS PPCS DM2S Saclay Golfier H. 331


In-vessel hydrogen deflagration/detonation analysis EFDA S&E Safety DER Cadarache Sardain P. 311

TW1-TSS-SEA5SEA5.31

Validation of computer codes and models EFDA S&E Safety DER Cadarache Sardain P. 313

TW1-TSS-SERF2 Tritium releases and long term impacts EFDA S&E Safety CEPN Fontenay Schneider T. 315

TW1-TTBA-001-D01 Test blanket module - Adaptation to next step machine EFDA TBM WCLL DM2S Saclay Poitevin Y. 169

TW1-TTBA-001-D04Tritium breeding module adaptation to next step machine - Adaptation of thermal-hydraulic performance to ITER specification

EFDA TBM WCLL DTP Cadarache Avakian G. 173

TW1-TTBA-002-D01Blanket manufacturing techniques - Definition of specification of a demonstrator

EFDA TBM WCLL DM2S Saclay Li Puma A. 175

TW1-TTBA-002-D02Blanket manufacturing techniques - Solid HIP demonstrator for fabrication and coating, fabrication of double wall tubes

EFDA TBM WCLL DTEN Grenoble Rigal E. 185

TW1-TTBA-002-D03Blanket manufacturing techniques - DIADEMO experimental program - Results of U bent DWT tests on Pb-Li

EFDA TBM WCLL DER Cadarache Cachon L. 189

TW1-TTBA-002-D05Blanket manufacturing techniques - Integrated mixed-powder HIP fabrication route for TBM with DWT

EFDA TBM WCLL DTEN Grenoble Bucci. Ph. 193

TW1-TTBA-004-D03 Processes and components - Blanket neutronic instrumentation EFDA TBM WCLL DED Cadarache Blandin C. 199

TW1-TTBA-005-D02 Safety and licensing : Pb-17Li/water interactions EFDA TBM WCLL DER Cadarache Louvet J. 201

TW1-TTBA-005-D03 Safety and licensing - TBM and TBM system safety EFDA TBM WCLL DM2S Saclay Li Puma A. 203

TW1-TTBA-006-D02 MHD effects - Test and modelling of natural MHD convection EFDA TBM WCLL DER Cadarache Cachon L. 209

TW1-TTBB-002-D02Blanket manufacturing techniques - Mock-up of first wall manufactured with alternative reduced cost fabrication technique

EFDA TBM HCPB DTEN Grenoble Rigal E. 213

TW1-TTBB-005-D03Development of ceramic breeder pebble beds - Characterization of Li2TiO3 pebble beds

EFDA TBM HCPB DECS Saclay Lulewicz J.D. 219

TW1-TTBB-005-D04Development of ceramic breeder pebble beds - Validation of Li2TiO3

fabrication with pre-industrial means of the lab fabrication steps - Mastering/optimisation

EFDA TBM HCPB DECS Saclay Lulewicz J.D. 223

TW1-TTMA-001-D01SiC-SiC ceramic composite - SiC-SiC composite development and characterization

EFDA TBM ADV DTEN Grenoble Couturier R. 227

TW1-TTMA-001-D09SiC-SiC ceramic composite - Joining development : process and mechanical characterization

EFDA TBM ADV DTEN Grenoble Saint Antonin F. 231

TW1-TTMS-001-D02RAFM steels - Irradiation performance - Neutron irradiation to 30-35 dpa at 325°C

EFDA TBM RAFM DMN Saclay Alamo A. 235

TW1-TTMS-002-D03RAFM steels - Metallurgical and mechanical characterization - Characterization and physical metallurgy


TW1-TTMS-002-D04RAFM steels - Metallurgical and mechanical characterization - Thermal ageing behaviour of EUROFER 97


TW1-TTMS-002-D16RAFM steels - Metallurgical and mechanical characterization - Mechanical properties of diffusion bonded welds (RAFM/RAFM HIP joint)

EFDA TBM RAFM DTEN Grenoble Bedel L. 247

TW1-TTMS-002-D18RAFM steels - Metallurgical and mechanical characterization - Mechanical properties of HIP powder steel

EFDA TBM RAFM DTEN Grenoble Gentzbittel J.M. 251

TW1-TTMS-003-D12 RAFM steels - Stress corrosion cracking in aqueous environments EFDA TBM RAFM DPC Saclay Raquet O. 257

TW1-TTMS-004-D02RAFM steels - Qualification fabrication processes - Powder HIP processing & specification

EFDA TBM RAFM DTEN Grenoble Gentzbittel J.M. 259

TW1-TTMS-004-D04RAFM steels - Qualification fabrication processes - EUROFER weldability

EFDA TBM RAFM DECS Saclay Fontes A. 267

TW1-TTMS-004-D05RAFM steels - Qualification fabrication processes - Dissimilar welding with filler

EFDA TBM RAFM DECS Saclay Fontes A. 271

TW1-TTMS-004-D06RAFM steels - Qualification fabrication processes - Solid HIP process qualification, application to complex shapes

EFDA TBM RAFM DTEN Grenoble Rigal E. 275

- 494 -


TW1-TTMS-005-D02RAFM steels - Rules for design, fabrication and inspection - Design code assessment and development

EFDA TBM RAFM DMN Saclay Tavassoli F. 279

TW1-TTMS-005-D05RAFM steels - Rules for design, fabrication and inspection - RAFM data collection and data base maintenance

EFDA TBM RAFM DMN Saclay Tavassoli F. 281

TW1-TTMS-006-D01RAFM steels - Qualification of high performance steels - ODS process and qualification

EFDA TBM RAFM DTEN Grenoble Cayron C. 283

TW1-TTMS-006-D03TTMS-6.3.1

RAFM steels - Qualification of high performance steels - Microstructure and mechanical properties


TW1-TVA-MANIP In-vessel dexterous manipulator EFDA VIV RH DTSI Fontenay Friconneau J.P. 137

TW1-TVA-RADTOL Radiation tolerance assessment of remote handling components EFDA VIV RH DTSI Fontenay Giraud A. 139

TW1-TVP-MAN1Optimisation and testing optimisation of CuCrZr/SS tube joints - Optimisation and manufacturing of samples by diffusion bonding

EFDA VIV PFC DTEN Grenoble Federzoni L. 63

TW1-TVV-HIP Improvement of HIP fabrication techniques EFDA VIV V/B DTEN Grenoble Bucci. Ph. 107

TW1-TVV-LWELD VV intersector joining - Vacuum vessel laser assembly EFDA VIV V/B DECS Saclay Aubert P. 87

TW1-TVV-ONEOptimisation of one step SS/SS and SS/CuCrZr HIP joints for retainment of CuCrZr properties

EFDA VIV V/B DTEN Grenoble Briottet L. 111

UT-PE-HFW Transparent polycristalline windows UT PI Diag DECS Saclay Lochet N. 351

UT-PFC&C-HIP Mechanical behaviour of HIP joints UT VIV PFC DMN Saclay Fissolo A. 355

UT-S&E-BLK Blanket safety – Design of a test section for MHD experimental program UT S&E Safety DER Cadarache Sardain P. 441

UT-S&E-Mitig Evaluation and mitigation of the risk connected to air or water ingress UT S&E Safety DER Cadarache Robin J.C. 443

UT-SM&C-CORMetal and oxide thermodynamic stability and solubility in water cooling systems

UT TBM MAT DPC Saclay Féron D. 413

UT-SM&C-LAM/Weld Laser weldability of LAM steels (Eurofer 97) UT TBM MAT DECS Saclay Aubert Ph. 417

UT-SS-RELReliability / availability assessment - Double walled tube concept, impact on the pressure tubes reliability / availability

UT SS SS DM2S Saclay Eid M. 447

UT-TBM/BB-IMBLA Improved breeding blanket UT TBM BLK DM2S Saclay Li Puma A. 385

UT-TBM/FC-SP

Separation of the D/T mixture from helium in fusion reactors using superpermeable membranes - Superpermeation : nonmonotonous energy dependence at low energy ion bombardment and the effect of membrane carbidization on hydrogen pemeation through the niobium membrane

UT TBM FC EP-LPTP Palaiseau Bacal M. 437

UT-TBM/MAT-BIM Dissimilar diffusion-bonded joints mechanical testing UT TBM MAT DTEN Grenoble Bedel L. 409

UT-TBM/MAT-LAM/MicInfluence of the martensite morphology on the plasticity behaviour of the Eurofer steel

UT TBM MAT DMN Saclay De Carlan Y. 421

UT-TBM/MAT-LAM3Microstructural investigation of Reduced Activation Ferritic-Martensitic (RAFM) steels by Small Angle Neutron Scattering (SANS)

UT TBM MAT DMN Saclay De Carlan Y. 425

UT-TBM/MAT-LM/MAG Liquid metal corrosion under magnetic field UT TBM BLK DPC Saclay Terlain A. 391

UT-TBM/MAT-LM/Refrac

Compatibility of refractory materials with liquid alloys UT TBM BLK DPC Saclay Dufrenoy T. 395

UT-TBM/MAT-LM/SiC Compatibility of SiCf/SiC composites with liquid Pb-17Li UT TBM BLK DPC Saclay Deloffre Ph. 399

UT-TBM/MAT-LM/WET Wetting of materials by liquid metals UT TBM BLK DPC Saclay Terlain A. 405

UT-TBM/MAT-ModModelling of the resistance of the dislocation network to the combined effect of irradiation and stress - Comparison of a pulsed and a continuous irradiation on the secondary defects structure in an annealed 316L steel

UT TBM MAT DMN Saclay Boulanger L. 429

UT-TBM/MAT-ODS Development of forming and joining technologies for ODS steels UT TBM MAT DTEN Grenoble Cayron C. 433

UT-VIV/AM-ActuatorsRemote handling techniques - Advanced technologies for high performances actuators

UT VIV RH DTSI Fontenay Friconneau J.P. 371

UT-VIV/AM-ECIrRemote handling techniques - Radiation tolerance assessment of electronic components from specific industrial technologies for remote handling and process instrumentation

UT VIV RH DTSI Fontenay Giraud A. 373

UT-VIV/AM-HMIRemote handling techniques - Graphical programming for remote handling techniques

UT VIV RH DTSI Fontenay Chodorge L. 377

- 495 -


UT-VIV/AM-HydroRemote handling techniques - Technology and control for hydraulic manipulator

UT VIV RH DTSI Fontenay Friconneau J.P. 381

UT-VIV/PFC-BDG Boron doped graphites UT VIV PFC DECS Saclay Lochet N. 359

UT-VIV/PFC-SIC/MJ Development of SiC/metal joining techniques UT VIV PFC DTEN Grenoble Delette G. 361

UT-VIV/PFC-TMM Thermo-mechanical models UT VIV PFC DM2S Saclay Nicolas A. 369

UT-VIV/PFC-W/CoatDevelopment of thick W CVD coatings for divertor high heat flux components

UT VIV PFC DTEN Grenoble Plissonnier M. 365

Programme AreaEFDA = EFDA Technology Programme Diag = DiagnosticsUT = Underlying Technology Programme Hea = Heating and Current DriveICF = Inertial Confinement Fusion Programme PFC = Plasma Facing Components

V/B = Vessel/BlanketField RH = Remote HandlingPI = Physic Integration MAG = MagnetsVIV = Vessel / In-Vessel Cryo = CryoplantM = Magnets WCLL = Water Cooled Lithium Lead BlanketTBM = Tritium Breeding & Materials HCPB = Helium Cooled Pebble Bed BlanketS&E = Safety & Environment ADV = Advanced MaterialsSS = System Studies RAFM = Reduced Activation Ferritic Martensitic steels

NS = Neutron SourceSafety = Safety and environmentSERF = Socio-EconomicsPPCS = Power Plant Conceptual StudiesBLK = BlanketMAT = MaterialsFC = Fuel Cycle

- 496 -

- 497 -

APPENDIX 5 : CEA SITES

Cadarache

Grenoble

Fontenay

SaclayCEA SITES

Sites with Fusion TasksAnother Site

Date post:	12-Mar-2021
Category:	Documents
Upload:	others
View:	1 times
Download:	0 times

Annual Report of the Association EURATOM/CEA 2001TW1-TPH-ICRANT ICRF Antenna and vacuum transmission...

Documents