Vertical Supports - 2.011-888-880-9191
componentsTransmission Line Support Systems
Antenna Support Bracketfor transmission lineThe Antenna Support Bracket angle mounts directly to a 4-1/2" (114 mm) OD antenna pipe mount or tower leg. Thisis ideal for supporting transmission line runs close to theantenna and for positioning the line to begin a vertical run.
B358 includes:
1 - 2" (51 mm) x 2" (51 mm) x 3/16" (5 mm)Angle, 3' (914 mm) long
1 - U-bolt Assembly
1 - Channel Attachment
Pipe-Leg Support Clampfor transmission lineClamps are heavy-duty 3/16" (5 mm) x 1-1/2" (38 mm)galvanized steel formed to fit common tower-memberdiameters. The pre-punched holes are used to attacheither Cushion or Butterfly Hangers or Coax Blocks using3/8" hardware. Snap-in Hangers are supported using theSnap-in Adapter (p. 2.02). Conduit runs and groundwire can also be attached to the Clamps.
Included are two 1/2" x 1-3/4" bolts, nuts, and lockwashers.
4-1/2” (114 mm)OD Pipe
Cushion Hangersand hardwarenot included
3’ (914 mm)
Tower Leg
Spacing to be inaccordance withtransmission linemanufacturerrecommendations
“A”
“B”
3-7/8”(98 mm)
6”(152 mm)
7/16”(11 mm)
diameter holesfor cushionhangers or
snap-inadapter plate
9/16”(14 mm)
dia hole forcoax block
Coax blocks andhardware not included
Use B1205screw, lockwasher, andB864 nut
7/16”(11 mm) dia hole for
ground wire andconduit attachment Two clamp
bolts included
3/16” (5 mm) x1-1/2” (38 mm)galvanized plate
Product
Number Description
B358 Antenna Support Bracket
Product Pipe OD Dim. “A” Dim. “B”
Number in (mm) in (mm) in (mm)
B1312 1.9 (48)-2 (51) 1' 1-13/16"(351) 1-15/16 (49)B123 2-3/8 (60)-2-1/2 (64) 1' 1-13/16"(351) 1-15/16 (49)
B135 2-7/8 (73)-3 (76) 1' 1-13/16"(351) 1-15/16 (49)
B142 3-1/4 (83)-3-1/2 (89) 1' 1-13/16"(351) 1-15/16 (49)B147 4 (102) 1' 1-13/16"(351) 1-15/16 (49)
B151 4-1/2 (114) 1' 1-13/16"(351) 1-15/16 (49)
B2173 5 (127) 1' 1-13/16"(351) 1-15/16 (49)B155 5-9/16 (141) 1' 1-13/16"(351) 1-15/16 (49)
B2174 6 (152) 1' 1-13/16"(351) 1-15/16 (49)
B163 6-5/8 (168) 1' 1-13/16"(351) 1-15/16 (49)B169 8-5/8 (219) 1' 1-13/16"(351) 1-15/16 (49)
B177 10-3/4 (273) 1' 1-13/16"(351) 1-15/16 (49)
B582 12-3/4 (324) 1' 1-13/16"(351) 1-15/16 (49)B1124 14 (356) 1' 1-13/16"(351) 1-15/16 (49)
B1305 16 (406) 1' 3-7/16"(392) 1-15/16 (49)
B1455 18 (457) 1' 3-7/16"(392) 2-7/16 (62)B2040 20 (508) 1' 6-11/16"(475) 1-15/16 (49)
B2041 22 (559) 1' 6-11/16"(475) 1-15/16 (49)
B2042 24 (610) 1' 6-11/16"(475) 1-15/16 (49)
1-888-880-91912.02 - Vertical Supports
componentsTransmission Line Support Systems
Round-Leg Support Clampfor transmission lineClamps are formed to fit small diameter tower members,such as solid-rod legs. The pre-punched holes are used toattach Cushion or Butterfly Hangers or Coax Blocks using3/8" hardware. Snap-in Hangers are supported with theSnap-in Adapter, below. Material is 3/16" (5 mm) x 1-1/2"(38 mm) galvanized steel.
Snap-In Adapterfor Pipe- & Round-leg Support ClampThe Snap-in Adapter, which bolts to the Pipe-leg orRound-leg Support Clamps, provides the capability to useSnap-in Hangers for support of coax transmission lines. Ifa run of waveguide needs to be installed. B1757(p. 6.01) will convert the 3/4" (19 mm) diameter hole toenable the use of 3/8" diameter hardware.
Product Pipe OD Dim. “A” Dim. “B”Number in (mm) in (mm) in (mm)
B1450 1/2 (13)-7/8 (22) 6-3/16" (157) 1-15/16 (49)
B1451 1 (25)-1-3/8 (35) 6-3/16" (157) 1-15/16 (49)B1452 1-1/2 (38)-1-7/8 (48) 6-3/16" (157) 2-5/16 (59)
Product
Number ForB2034 12 Coax runs
B1717 9 Coax runs
B1720 6 Coax runs
Universal Snap-In Bracketsfor Angle- or Pipe-LegThe Universal Snap-In Bracket supports up to 16 Snap-InHangers for support of coax transmission lines on angle-leg or pipe-leg structures. Also provided are 7/16" (11mm) diameter holes to support Cushion or ButterflyHangers. Galvanized.
12 16 Angle Leg Size Pipe Leg Size
Runs Runs in (mm) in (mm)
B2249 B2252 2-1/2 (64) x 2-1/2 (64) 1-1/2 (38) OD toto 4 (102) x 4 (102) 5-9/16 (141) OD
B2250 B2253 5 (127) x 5 (127) to 6 (152) OD to
6 (152) x 6 (152) 8-5/8 (219) ODB2251 B2254 8 (203) x 8 (203) 10-3/4 (273) OD to
12-3/4 (324) OD
6”(152 mm) Use B1205 Screw, Lock
washer and B864 Nut
7/16”” (11 mm)diameter hole forground wire and
conduit attacnment
Two clampbolts included
Solid rod leg“A”
“B”
3-7/8”(98 mm)
Cushionhangers andhardware not
included
7/16(11 mm)diameterhole forCushionHanger
or Snap-Inadapter plate
9/16 (14 mm)diameter holefor Coax Block
Coax Blocks andhardware not included
Pipe-legsupportclamp
Snap-inHanger
3/4” (19 mm)diameter holes
for Snap-inHangers
Angle-Legor Pipe-LegIncluded 1/2" hardware
7/16" (11 mm) diameterholes for Cushion Hangers
3/4" (19 mm) diameter holesfor Snap-In Hangers
2-1/2"(64 mm)
2-1/2"(64 mm)
Angle 3-Leg Support Clampfor transmission lineClamps provide support for either six Cushion Hangers,six Snap-In Hangers, or two Coax Blocks. Material isgalvanized steel.
Product Leg Size
Number in (mm)
B1753 3-1/2 (89) x 3-1/2 (89) & 4 (102) x 4 (102)
Coax Blocksand hardwarenot included
Holes alsoprovided for 6
Snap-In orButterfly Hangers
and CushionHangers or 2Coax Blocks
Cushion Hangersand hardware not
included
Snap-InHangers not
included
Vertical Supports - 2.031-888-880-9191
componentsTransmission Line Support Systems
Climbing-Ladder Support Bracketfor transmission lineThe Bracket supports up to seven Snap-In Hangers forsupport of coax transmission line on climbing laddersbuilt with vertical angle members. The Bracket attaches toangle sizes from 2-1/2" (64 mm) x 2-1/2" (64 mm) to4"(102) x 4"(102) and may mount on either leg of theangle. To use cushion hangers, B1757 (p. 6.01) willconvert the 3/4" (19 mm) diameter hole to enable the useof 3/8" diameter hardware.
Galvanized.
Product Leg SizeNumber in (mm)
B1558 2-1/2 (64) x 2-1/2 (64) to 4 (102) x 4(102)
Ladder rungClimbing ladder
angle rail
Snap-InHanger notincluded
Seven 3/4” (19 mm)diameter holes forSnap-In Hangers
Angle 4-Leg Support Clampfor transmission lineClamps provide support for either six Cushion Hangers,six Snap-In Hangers, or two Coax Blocks. Material is3/16" (5 mm) galvanized steel.
Product Leg SizeNumber in (mm)
B1472 2 (51) x 2 (51) & 3 (76) x 3 (76)
B1473 3-1/2 (89) x 3-1/2 (89) & 4 (102) x 4 (102)B1474 5 (127) x 5 (127) & 6 (152) x 6 (152)
B1475 8 (203) x 8 (203)
Holes alsoprovided for6 Snap-InButterfly
Hangers andCushion
Hangers or 2Coax Blocks
CushionHangers
andhardware
notincluded
Coax Blocksand hardwarenot included
Snap-In Hangersnot included
Cluster Support BracketBracket models support either Cushion Hangers or Snap-In Hangers and are fabricated from 1/8" (3 mm) hot-dipgalvanized steel. The Bracket mounting hole is 9/16" (14mm) diameter. The B2211 is 10-1/4" (260 mm) long.
ProductNumber Accommodates
B1258 7 Cushion Hangers
B1259 7 Snap-In HangersB2211 9 Snap-In Hangers
5-1/4" (133 mm)
7-1/2" (191 mm)
2" (51 mm)
Installation ExamplesTransmission line runs can be clamped directly to a roundtower leg or diagonal, as shown (Fig. A), by using twoclamp heads back-to back. The clamp heads must bebolted together (Fig. B) before installing either theCushion Hanger or the adjustable Clamp. Threaded rodstandoffs may be used to extend the transmission lineaway from obstructions, for either angle-leg towers (Fig.C) or pipe-leg towers.
Diagonal tower member
Use B238 Screw andB864 Nut to join
clamp heads
B185 AdjustableClamp
CushionHanger
Transmission-line
B399 ClampHead
3/8” Threaded Rod
B1292 Cross
B238 Screw andLockwasher
B1576Universal Clamp
Figure A
Figure B
Figure C
B399 Clamp Head
CushionHanger
3/8” hardware
3/8”hardware
B185AdjustableClamp
1-888-880-91912.04 - Vertical Supports
componentsTransmission Line Support Systems
Super CrossThe Super Cross, made of lightweight aluminium, isthreaded for 3/8" hardware to support up to 5 cushionHangers. Transmission line support is simplified sinceonly one tower attachment point supports multipleCushion Hangers, each of which can support multipletransmission lines, depending on the line size. Attach-ment hardware includes a 3/8" diameter x 3" (76 mm)long stud, lockwasher and nut.
CrossThe B1292 Cross is tapped through for convenience ofleveling Cushion Hangers on the 3/8" Threaded Rod.Designed for versatility and made of PVC, the Cross maybe used in combinations to accommodate any number orsize of transmission line runs.Five per Package.
1-1/2”(38 mm)diameter
3/4”(38 mm)
Tower member
B240 or B251CombinationSquare Rail
B174 3/8” SpringNut with square
spacer
3-3/8” (86 mm)B357 Super Cross
Product
Number Description
B357 Super Cross
Product
Number Description
B1292 Cross, 5 per package
Standoff Kitfor PipeThe Standoff Kit provides 7/16" (11 mm) or a 3/4" (19mm) diameter hole for support of a Cushion or ButterflyHanger or Snap-In Hanger. The Bracket is attached directlyto a round tower leg or diagonal with the included clamp.The Bracket and clamp are stainless steel.
Ten per package.
1 Kits with 7/16" (11 mm) hole include 3/8" diameter fillester slotted screw, lock washerand nut.2 Bracket only, clamp not included, will accept up to 3/4" banding.
Product Number Product Number
Pipe OD with 7/16" (11 mm) with 3/4" (19 mm)in (mm) hole, 10/pack1 hole, 10/pack
3/4 (19) - 1-1/2 (38) B2126 —
1-1/2 (38) - 3 (76) B2127 B21313 (76) - 4 (102) B2128 B2132
4 (102) - 5 (127) B2129 B2133
5 (127) - 6 (152) B2130 B21343 (76) and up B21352 B21362
Snap-In BoxSnap-In Box provides three 3/4" (19 mm) diameter holesfor the attachment of Snap-In Hangers. The Box mountsto tower members, Universal Clamps or Standoff Kitswith included 3/8" hardware.
Hot-dip galvanized after fabrication.
Product
Number DescriptionB2143 Snap-In Box
7/16” (11 mm) hole for 3/8”hardware or 3/4” (19 mm)hole for Snap-In Hanger
Standoff Kit with 7/16” (11 mm)hole, ordered separately
Snap-In Box
Three 3/4” (19 mm)dia holes for Snap-In
Hangers, orderedseparately, (p.6.06)
Vertical Supports - 2.051-888-880-9191
componentsTransmission Line Support Systems
Heavy Duty Welded Coax SupportLadderwith Angle Rail and RungsThe Coax Support Ladder, in lengths of 5' (1.524 m), 10'(3.048 m), and 20' (6.096 m), is provided in weldedsections, that include 2-1/2" (64 mm) x 2-1/2" (64 mm) x1/4" (6 mm) angle rails, angle rungs, and hardware fortower attachment. The maximum span between towerattachments is 20' (6.096 m) Two hardware mounting kitsare provided with the 20' (6.096 m) ladder, and onehardware mounting kit is provided with the 10' (3.048m) ladder and the 5' (1.524 m) ladder. Each hardwaremounting kit includes two brackets and hardware toattach the ladder to the tower.
There are two ladder widths available, 3' 1-1/2" (953mm) for 12 runs of coax and 3' 10-1/2" (1.181 m) for 15runs of coax. The rung spacing is 3' 4" (1.016 m) and has3/4" (19 mm) holes for Snap-In Hangers and 7/16" (11mm) holes for Cushion Hangers or Butterfly Hangers tosupport coax transmission line up to 2-1/4" diameter.
Each ladder section is furnished with splices to intercon-nect with the next section. The ladder for round towermembers attaches to an 1-1/2" (38 mm) to 4-1/2" (1.231m) OD round tower girt or diagonal with includedbrackets and hardware. The ladder for angle towermembers attaches to a 5" (127 mm) maximum, girt ordiagonal, with included J-bolts and backing plates. Anoptional J-bolt can be ordered when the angle towermember exceeds 5" (127 mm). J-bolt part number B2335(p. 14.04) will accommodate angle tower members from5" (127 mm) to 7" (178 mm) in width.
When the Ladder extends to ground level below thelowest girt, a Ladder Base Kit is required to support theladder at ground level. The Kit consists of stub angles thateither install in a concrete footing or bolt to a concretepad. Material is hot-dip galvanized after fabrication.
Twelve 3/4” (19 mm) diameter holesfor Snap-In Hangers and twelve 7/16”(11 mm) diameter holes for Cushion
and Butterfly Hangers
1-1/2”(38 mm) to
4-1/2”(114 mm)
Round towergirt or
diagonal
3/4” (19 mm)diameter holes
7/16”(11 mm)diameter
holes
1-1/2”(38 mm)
1-1/2”(38 mm)
2” (51 mm) min.5” (127 mm) max.
Angle tower girtor diagonal
3’ 1-1/2”(953 mm)
3’ 4” (1.016 m)rung spacing
10’ (3.048 m)preferred spacing20’ (6.096) max.
Coax Ladder for Angle Tower Member
ProductNumber Description
B2443 5' (1.524 m) Coax Ladder, 3' 1-1/2" (953 mm) wide for 12 runs
of coax, attaches to angle tower memberB2444 10' (3.048 m) Coax Ladder, 3' 1-1/2" (953 mm) wide for 12
runs of coax, attaches to angle tower member
B2445 20' (6.096 m) Coax Ladder, 3' 1-1/2" (953 mm) wide for 12runs of coax, attaches to angle tower member
B2446 5' (1.524 m) Coax Ladder, 3' 10-1/2" (1.181 m) wide for 15
runs of coax, attaches to angle tower memberB2447 10' (3.048 m) Coax Ladder, 3' 10-1/2" (1.181 m) wide for 15
runs of coax, attaches to angle tower member
B2448 20' (6.096 m) Coax Ladder, 3' 10-1/2" (1.181 m) wide for 15runs of coax, attaches to angle tower member
B2487 Angle Member Hardware Mounting Kit
B1751 Ladder Base Kit
Coax Ladder for Round Tower Member
ProductNumber Description
B2164 5' (1.524 m) Coax Ladder, 3' 1-1/2" (953 mm) wide for 12 runsof coax, attaches to round tower member
B2165 10' (3.048 m) Coax Ladder, 3' 1-1/2" (953 mm) wide for 12
runs of coax, attaches to round tower memberB2166 20' (6.096 m) Coax Ladder, 3' 1-1/2" (953 mm) wide for 12
runs of coax, attaches to round tower member
B2255 5' (1.524 m) Coax Ladder, 3' 10-1/2" (1.181 m) wide for 15runs of coax, attaches to round tower member
B2256 10' (3.048 m) Coax Ladder, 3' 10-1/2" (1.181 m) wide for 15
runs of coax, attaches to round tower memberB2257 20' (6.096 m) Coax Ladder, 3' 10-1/2" (1.181 m) wide for 15
runs of coax, attaches to round tower member
B2486 Round Member Hardware Mounting KitB1751 Ladder Base Kit
1-888-880-91912.06 - Vertical Supports
componentsTransmission Line Support Systems
Bolt-Together Coax Support Ladderwith Angle Rail and RungsCoax Support Ladders are available in three lengths, 5'(1.524 m), 10' (3.048 m) and 20' (6.096 m), and areavailable in factory assembled or field assembled sections.Each ladder section is constructed of angle rungs bolted to1-3/4" (44 mm) x 1-3/4 (44 mm) angle rails and includesthe hardware for tower attachment. The maximum spanbetween tower attachments is 10' (3.048 m). Two hardwaremounting kits are provided with the 20' (6.096 m) ladderand one hardware mounting kit is provided with the 10'(3.048 m) ladder and the 5' (1.524 m) ladder. Eachmounting hardware kit includes two brackets and hard-ware to attach the ladder to the tower.
The ladder is available in two widths, 2' 8-1/4" (819 mm)for 12 runs of coax and 3' 3-3/4" (1.010 m) for 15 runs ofcoax. The rung spacing is 3' 4" (1.016 m) and has 3/4" (19mm) holes for Snap-In Hangers and 7/16" (11 mm) holesfor Cushion or Butterfly Hangers to support coax transmis-sion lines up to 1-5/8" diameter.
Factory Assembled Coax Ladder for Angle Tower Member
Product
Number DescriptionB2455 5' (1.524 m) Factory Assembled Coax Ladder, 2' 8-1/4" (819 mm) wide for 12 runs of coax, attaches to angle tower member
B2456 10' (3.048 m) Factory Assembled Coax Ladder, 2' 8-1/4" (819 mm) wide for 12 runs of coax, attaches to angle tower member
B2457 20' (6.096 m) Factory Assembled Coax Ladder, 2' 8-1/4"(819 mm) wide for 12 runs of coax, attaches to angle tower memberB2458 5' (1.524 m) Factory Assembled Coax Ladder, 3' 3-3/4" (1.01 m) wide for 15 runs of coax, attaches to angle tower member
B2459 10' (3.048 m) Factory Assembled Coax Ladder, 3' 3-3/4" (1.01 m) wide for 15 runs of coax, attaches to angle tower member
B2460 20' (6.096 m) Factory Assembled Coax Ladder, 3' 3-3/4" (1.01 m) wide for 15 runs of coax, attaches to angle tower memberB2487 Angle Member Hardware Mounting Kit
B1751 Ladder Base Kit
Factory Assembled Coax Ladder for Round Tower MemberProduct
Number Description
B2467 5' (1.524 m) Factory Assembled Coax Ladder, 2' 8-1/4" (819 mm) wide for 12 runs of coax, attaches to round tower memberB2468 10' (3.048 m) Factory Assembled Coax Ladder, 2' 8-1/4" (819 mm) wide for 12 runs of coax, attaches to round tower member
B2469 20' (6.096 m) Factory Assembled Coax Ladder, 2' 8-1/4"(819 mm) wide for 12 runs of coax, attaches to round tower member
B2470 5' (1.524 m) Factory Assembled Coax Ladder, 3' 3-3/4" (1.01 m) wide for 15 runs of coax, attaches to round tower memberB2471 10' (3.048 m) Factory Assembled Coax Ladder, 3' 3-3/4" (1.01 m) wide for 15 runs of coax, attaches to round tower member
B2472 20' (6.096 m) Factory Assembled Coax Ladder, 3' 3-3/4" (1.01 m) wide for 15 runs of coax, attaches to round tower member
B2486 Round Member Hardware Mounting KitB1751 Ladder Base Kit
Each ladder section is furnished with splices to intercon-nect with the next section. The ladder for round towermembers attaches to an 1-1/2" (38 mm) to 4-1/2" (114mm) OD round tower girt or diagonal with includedbrackets and hardware. The ladder for angle tower mem-bers attaches to a 5" (127 mm) maximum, girt or diagonal,with included J-bolts and backing plates. An optional J-boltcan be ordered when the angle tower member exceeds5"(127 mm). J-bolt part number B2335 (p. 14.04) willaccommodate angle tower members from 5" (127 mm) to7" (178 mm) in width.
When the Ladder extends to ground level below the lowestgirt, a Ladder Base Kit is required to support the ladder atground level. The Kit consists of stub angles that eitherinstall in a concrete footing or bolt to a concrete pad.
Material is hot-dip galvanized after fabrication.
Vertical Supports - 2.071-888-880-9191
componentsTransmission Line Support Systems
Field Assembled Coax Ladder for Angle Tower MemberProduct
Number Description
B2449 5' (1.524 m) Field Assembled Coax Ladder, 2' 8-1/4" (819 mm) wide for 12 runs of coax, attaches to angle tower memberB2450 10' (3.048 m) Field Assembled Coax Ladder, 2' 8-1/4" (819 mm) wide for 12 runs of coax, attaches to angle tower member
B2451 20' (6.096 m) Field Assembled Coax Ladder, 2' 8-1/4"(819 mm) wide for 12 runs of coax, attaches to angle tower member
B2452 5' (1.524 m) Field Assembled Coax Ladder, 3' 3-3/4" (1.01 m) wide for 15 runs of coax, attaches to angle tower memberB2453 10' (3.048 m) Field Assembled Coax Ladder, 3' 3-3/4" (1.01 m) wide for 15 runs of coax, attaches to angle tower member
B2454 20' (6.096 m) Field Assembled Coax Ladder, 3' 3-3/4" (1.01 m) wide for 15 runs of coax, attaches to angle tower member
B2487 Angle Member Hardware Mounting KitB1751 Ladder Base Kit
Field Assembled Coax Ladder for Round Tower MemberProduct
Number Description
B2461 5' (1.524 m) Field Assembled Coax Ladder, 2' 8-1/4" (819 mm) wide for 12 runs of coax, attaches to round tower memberB2462 10' (3.048 m) Field Assembled Coax Ladder, 2' 8-1/4" (819 mm) wide for 12 runs of coax, attaches to round tower member
B2463 20' (6.096 m) Field Assembled Coax Ladder, 2' 8-1/4"(819 mm) wide for 12 runs of coax, attaches to round tower member
B2464 5' (1.524 m) Field Assembled Coax Ladder, 3' 3-3/4" (1.01 m) wide for 15 runs of coax, attaches to round tower memberB2465 10' (3.048 m) Field Assembled Coax Ladder, 3' 3-3/4" (1.01 m) wide for 15 runs of coax, attaches to round tower member
B2466 20' (6.096 m) Field Assembled Coax Ladder, 3' 3-3/4" (1.01 m) wide for 15 runs of coax, attaches to round tower member
B2486 Round Member Hardware Mounting KitB1751 Ladder Base Kit
Twelve 3/4” (19 mm) diameter holesfor Snap-In Hangers and twelve 7/16”(11 mm) diameter holes for Cushion
and Butterfly Hangers
2” (51 mm) min.5” (127 mm) max.angle tower girt or
diagonal
3/4” (19 mm)diameter holes
1-1/2” (38 mm)to 4-1/2”
(114 mm) Roundmember tower girt
or diagonal
2’ 8-1/4”(819 mm)
3’ 4” (1.016 m)rung spacing
10’ (3.048 m)maximum spacing
1-1/4”(32 mm)
1-1/4”(32 mm)
7/16”(11 mm)diameter
holes
Included1/2”
diameterhardware
Bolt Together Coax Support Ladder, continued
1-888-880-91912.08 - Vertical Supports
componentsTransmission Line Support Systems
Lightweight Support RailLengths of B240 or B251 Combination Square Rail can bejoined together with B252 Splices to fabricate a light-weight vertical transmission line support.
One side of the Square Rail is used to attach CushionHangers at desired intervals using Spring Nuts and 3/8"hardware. The other side attaches to the tower usingvarious methods, depending on the tower construction.The recommended maximum span between towerattachment points is 20 feet (6.096 m), based on aloading of 20 lb (27.120 Nm) per lineal foot.
Transmission line runs of this type should be installednear a climbing ladder or tower leg since the support railitself offers no footing for workers installing the line-support components.
Combination Square RailRails are 1-5/8" (41 mm) square, 12-gauge (3 mm)galvanized steel that is spot welded back-to-back. Whenused for horizontal transmission line support, the top Railslot is used for attachment to Pipe Heads with 1/2"hardware and 1/2" Spring Nuts (B262). The lower Railslot is used to attach transmission line with 3/8" hardwareand 3/8" Spring Nuts (B174). See page 6.01
Product
Number Description
B240 10' (3.048 m) longB251 20' (6.096 m) long
Splicefor Combination Square RailThe Splice is used to join sections of Combination SquareRail. It includes two splice plates and four bolts, washersand nuts. All parts are galvanized.
ProductNumber Description
B252 Combination Square Rail Splice
B297 ClipAngle
B174 SpringNut and 3/8”
hardware
CushionHanger
B1292 Cross
B252Square
Rail Splice
TowerMember
B240 10’(3.048 m)
lengthor
B251 20’(6.096 m)
lengthCombinationSquare Rail
Spacing inaccordance withtransmission line
manufacturerrecommendations
Towermember
B252Square
Rail Splice
B251CombinationSquare Rail
B297 Clip Angle
B1577Universal Clamp
B682 1/2”Bolt
Assembly
Towergirts
B262 SpringNut and 1/2”s.s. hardware
7/16” (11 mm) splice holes
Typical Transmission line Attachment
Alternate Clamping Method
Typical Clamping Method
Vertical Supports - 2.091-888-880-9191
componentsTransmission Line Support Systems
Lightweight Support Ladderwith Square RailVertical support ladders for self-supporting towers can befabricated using standard products, as shown. Laddersare 3' 4" (1.016 m) wide and are attached to the face ofthe tower. The recommended maximum span is 20'(6.096 m) between tower attachment points. This isbased on a loading of 40 pounds (54.233Nm) per linealfoot resulting from a 100 mph (161 km/h) wind load onseven 1-1/2" (30 mm) elliptical waveguide runs.
Cross Pieces, for either Cushion Hangers or Snap-InHangers, are attached at desired intervals to one side ofCombination Square Rails using 3/8" Bolts and SpringNuts (p. 14.03). The other side of the CombinationSquare Rails attach to the tower with 1/2" hardware.Exact methods of attachment depend on the type of towerconstruction. Lengths of the rail are joined together withB252 Splices. Attaching hardware for the Rail and CrossPieces is ordered separately.
B251Combination
Rail
B1647 orB291 CrossPiece, 3’-4”(1.016 m)
TowerMember
TowerMember
B252Splice
B291 Cross Piece
Cushion Hanger clamp headsattached with B298 Screws andB174 3/8" Spring Nuts
Transmission line
B843 3/8" x 1-1/4" Bolt,Lock Washer, B174 3/8"Spring Nut
B251 CombinationSquare Rail
B297 Clip Angle
B262 Spring Nut and 1/2" s.s. hardware
Tower girts
B682 1/2" BoltAssembly
B1577 Universal Clamp
B297 Clip
B251 CombinationSquare Rail
Typical Transmission Line Attachment
Alternate Clamping Method
Typical Clamping Method
1-888-880-91912.10 - Vertical Supports
componentsTransmission Line Support Systems
Adjustable Clamping BarThe Adjustable Clamping Bar is used to support verticaltransmission-line runs and to terminate horizontalbridges on the face of angle leg towers. This is an ex-tremely versatile product. Slots in the Clamping Bar allowit to attach to a variety of tower widths.
Galvanized.
Adjustable Clamping Bar includes:
1 - 4' 4" (1.321 m) long Clamping Bar
2 - 3/8" x 3-1/4" Bolts and Lock Washers
2 - 3/8" Universal Clamps
2 - 2-1/2" (64 mm) Standoff Brackets
Product
Number DescriptionB516 Adjustable Clamping Bar
Cross Piecefor Square Rail Support LadderCross Piece ladder rungs are available to support eitherCushion Hangers or Snap-in Hangers. The B291, fabricatedfrom 1-5/8" (41 mm) square rail, enables the attachment ofeleven Cushion Hangers using 3/8" Spring Nuts (p. 14.03)and hardware. Multiple transmission line runs can besupported in each Cushion Hanger, depending on the linesize.
The B1647, fabricated from angle steel, provides sixteen3/4" (19 mm) holes for installing Snap-in Hangers. Thehole spacing of 2-1/2" (64 mm) on-centers allows 16 runsof up to1-5/8" coax to mounted on each Cross Piece.
Both Cross Pieces are 3' 4" (1.016 m) long and are hot-dip galvanized steel.
B251CombinationSquare RailSnap-In
Hanger
3/4" (19 mm)dia hole
B251CombinationSquare Rail
3' 4" (1.016 m)3' 2" (965 mm)
Sixteen 3/4" (19 mm)holes for Snap-InHangers
B174 3/8" SpringNut and B834 3/8"x 1-1/4" Bolt, LockWasher (notincluded)
B251CombinationSquare Rail
AA
B516 AdjustableClamping Bar
Cushion Hanger, B298 Screw,and B174 3/8" Spring Nut
B516 Adjustable Clamping Bar
B513 All-Purpose Angle
B501 or B502 Bridge Channel
B515 Clip Angleand B174 3/8"Spring Nut
3" (76 mm)standofftower leg
Two Standoff Brackets can be boltedanywhere along Clamping Bar
Adjustable from1' (305 mm) x 4' 2" (1.270 m)
StandoffBracket
Tower leg
Product
Number Description
B291 For Cushion HangersB1647 For Snap-In Hangers
View A-A
Vertical Supports - 2.11
componentsTransmission Line Support Systems
1-888-880-9191
Monopole Transmission Line BracketMonopole Transmission Line Bracket supports three runsof coax or waveguide per Bracket. Multiple Brackets maybe used per level depending upon the pole diameter. TheBrackets are strapped to the Pole using the B1769 Band-ing (p. 13.05) and have 7/16" (11 mm) holes for CushionHangers, Butterfly Hangers, or 3/4" (19 mm) diameterholes for Snap-In Hangers
Product
Number Hole Size
B2391 7/16" (11 mm) and 3/4" (19 mm)
B2336 3/4" (19 mm)
Strap-On Bracketfor Polygon & Round HolesBracket is strapped on to a pole using B1769 Banding
(p. 13.05) and provides a 9/16" (14 mm) diameter holefor attachment of Coax Blocks or Snap-In Adapter Plates.
Galvanized.
Minimum one bandrequired at top.Second band maybe used foradditional support.
Banding, Bucklesand Tensioning Toolsordered separately,(p. 13.05)
MonopoleTransmission LineBracket
Snap-In Hangersordered separately(p. 6.07)
Banding, Buckles andTensioning Tools orderedseparately (p. 13.05)
Coax Block and HardwareKit ordered separately(p. 6.05)
Monopole Coax Support KitMonopole Support Kits support coax on round or polygo-nal poles. The Bracket supports nine or twelve runs of7/8" or 1-5/8" coax. Brackets are secured to the pole usingB1769 Banding (p. 13.05). The Bracket is galvanizedsteel.
Snap in hangersordered separately(p. 6.07)
Banding, Bucklesand TensioningTools orderedseparately(p. 13.05)
B2421 Shown
Product
Number Capacity
B2421 9 runs of 7/8" coax
B2422 12 runs of 7/8" coax
B2423 9 runs of 1-5/8" coax
B2424 12 runs of 1-5/8" coax
Product
Number Description
B1844 Strap-On Bracket
1-888-880-91912.12 - Vertical Supports
componentsTransmission Line Support Systems
Covered Monopole Coax Support KitCovered Monopole Coax Support Kits support coax onround or polygonal poles and protects the coax from theelements. Intermediate and Top Kits include two Strap-OnBrackets for coax support, and Base Kits include threeStrap-On Brackets for coax support. The Bracket supportsnine or twelve runs of 7/8" or 1-5/8" coax. The 22-gauge(.85 mm) x 8' (2.438 m) steel Covers bolt directly to theBrackets. Brackets are secured to the pole using B1769Banding (p. 13.05). The Kits are self splicing. An Align-ment Tool is provided with each Base Kit for the properinstallation of the Brackets. The Bracket and Covers aregalvanized steel.
Banding, Buckles andTensioning Tool orderedseparatetly (p. 13.05)
8’ (2.438 m) cover
Strap on Bracket
Snap-In Hanger Mountfor Pipe LegThe Snap-In Hanger Mount supports up to 12 Snap-InHangers for support of coax transmission lines on pipe-legs from 1' 6" (106 mm) up to 2' 6" (762 mm) in diam-eter. The Mount is 2' 11-1/4" (895 mm) long.
Galvanized.
2’ 11-1/4” (895 mm)
Twelve 3/4” (19 mm)diameter holes forSnap-In Hangers
3’ (76 mm) typ.
Product Product
Number for Number forBase Kit Int./Top Kit Capacity
B2243 B2392 9 runs of 7/8" coax
B2244 B2393 12 runs of 7/8" coaxB2245 B2394 9 runs of 1-5/8" coax
B2246 B2395 12 runs of 1-5/8" coax
Product Pipe SizeNumber in (mm)
B1949 1' 4" to 1' 6" (106 to 457)
B1950 1' 8" to 1' 10" (508 to 559)B1951 2' to 2' 2" (610 to 660)
B1968 2' 4" to 2' 6" (711 to 762)
Vertical Supports - 2.131-888-880-9191
componentsTransmission Line Support Systems
Wall-Mounted Coax Support BracketWall-Mounted Coax Support Brackets support vertical orhorizontal runs on a wall surface. The three Bracketmodels, furnished with 3/4" (19 mm) holes for Snap-InHangers (p. 6.07), support four, eight, or twelve runs ofcoax. Two 7/16" (11 mm) diameter holes on each side ofthe Bracket provide for attachment of grounding lugs.Order bracket to wall attaching hardware separately (section14).
Wall-Mounted Coax Support Kitwith CoverWall-Mounted Coax Support kits include two wall-mounted brackets for coax support and a steel cover toprotect the runs on a wall surface. The wall-mountedbrackets, furnished with 3/4" (19 mm) holes for Snap-InHangers (p. 6.07), support four, eight, or twelve runs of1/2" (13 mm) through 1-5/8" (41 mm) coax. The 16-gauge (1.6 mm) steel cover bolts directly to the bracketsand has two 7/16" (11 mm) diameter holes on each sidefor attaching grounding lugs. Optional Cover Splices areavailable to interconnect covers for the 4-run and 8-runKits. Covers for the 12-run Kit overlap with each otherand thus are self splicing.
Order bracket to wall attaching hardware separately (section14)
Product
Number Description WidthB1589 Wall mounted Coax Support Kit 11-1/2" (292 mm)
for 4-runs, 7'11-3/4" (2.432 m) long
B1590 Wall mounted Coax Support Kit 1'9-1/2" (546 mm)for 8-runs, 7'11-3/4" (2.432 m) long
B1591 Wall mounted Coax Support Kit 2'6-3/4" (781 mm)
for 12-runs, 8'1-1/2" (2.477 m) longB1607 Cover Splice for wall mounted —
Coax Support Kit, 4 runs
B1608 Cover Splice for wall mounted —Coax Support Kit, 8 runs
2-1/2" (64 mm) typ.
3/4" (19 mm)dia holes forSnap-InHangers
9/16" (14 mm) diaholes for wallattachment
Two 7/16" (11 mm) diaholes on 1" (25 mm)centers for ground lug
Width
8' (2.438 m)nominal
4' (1.219 m)
1' 11-7/8" (606 mm)
1' 11-7/8" (606 mm)
3/8" (10 mm) diatapped hole forcover attachment
Two 7/16" (11 mm) diaholes on 1" (25 mm)centers for ground lug
Width
Product Wall MountedNumber Coax Support Bracket Width
B1586 for 4 runs 11-1/4" (286 mm)
B1587 for 8 runs 1'9-1/4" (540 mm)B1588 for 12 runs 2'6-1/2" (775 mm)