“Products With Integrity” - Kumar Industries...KUMAR INDUSTRIES, INC. Manufacturers of...

KUMARI N D U S T R I E S , I N C .

Manufacturers of “Nu-Strut” Framing Channel System & Custom Steel Fabrication

4775 Chino AVenue • Chino, CA 91710 • tel: (909) 591-0722 • fAx: (909) 591-6334 www.kumarindustries.net • engineering Catalog no 52

“Products With Integrity”

ChAnnels:nu-strut Channels are manufactured by the cold roll forming method from low carbon strip steel. one side of the channel provides a continuous slot with two lips. the attachment of hardware such as spring nuts, which are toothed, is assured to be secure.steel material conforms to the following specifications.

gAuge finish Astm speC no. 12 gauge gr and hDg Astm A1011 ss gr 3 12 gauge pg Astm A653 gr 33 14 gauge gr & hDg Astm A1011 ss gr 33 14 gauge pg Astm A653 gr 33 16 gauge gr & hDg Astm A1011 ss gr 33 16 gauge pg Astm A653 gr 33 19 gauge gr & hDg Astm A1008 19 gauge pg Astm A653 gr 33

fittings:nu-strut fittings are manufactured from hot-rolled, pickled and oiled strip steel or bar steel conforming to Astm A575, A576, A635, or A36. the fitting steel also meets the physical requirements of Astm-A1011-ss-gr33.

nuts AnD sCrews:nu-strut Channel nuts are manufactured from steel bar stock, which has been case hardened, after the stamping process. All bolts and nuts have American national coarse screw threads. nuts are zinc coated. Channel nuts available with or without spring, when provided with spring, galvanized spring steel wire is used. Bar stock used to manufacture channel nuts conforms to Astm A1011 ss gr 33, screws conform to sAe J429 gr 2 (also meets & exceeds Astm A307).

finishes:pl (plain) - mill finish.

gr (green) - Channels available in standard green enamel semi-gloss paint applied after steel has been thoroughly cleaned and phosphated.

pg (pre-galvanized) - galvanized steel is used to manufacture channels. Channel sections conform to Astm A653-g90.

hDg (hot Dip galvanized) - Channel which has been hot dip galvanized after fabrication conforms to Astm A123, Astm A153, or Astm A386.

MAteRiAls And specificAtion detAilsNU-STRUT

KUMAR INDUSTRIES, INC. tel: (909) 591-0722 fax: (909) 591-6334

Channels ......................................................................................................2

Channel Combinations ................................................................................3

Punched Channel Patterns ..........................................................................4

Engineering Data .........................................................................................5

Channel Nuts .............................................................................................11

Flat Plate Fittings .......................................................................................13

90° Angle Fittings .......................................................................................16

“Z” Fittings .................................................................................................19

“U” Fittings .................................................................................................20

Clevis/Angular Fittings ..............................................................................21

Angular Fittings ..........................................................................................22

Wing Fittings ..............................................................................................24

Brackets .....................................................................................................27

Beam Clamps ............................................................................................31

Post Bases .................................................................................................34

End Caps & Closure Strips ........................................................................36

Pipe Clamps ...............................................................................................37

Electrical Accessories ................................................................................39

Trollies & Supports .....................................................................................41

Saddles & Maple Clamps ..........................................................................42

Swivel Hangers ..........................................................................................43

Concrete Inserts .........................................................................................44

Hardware ....................................................................................................48

Tubing Clamps & Pipe Straps ...................................................................50

Numerical Parts Index ................................................................................51

NU-STRUT tAble of contents

KUMAR INDUSTRIES, INC. TEl: (909) 591-0722 FAx: (909) 591-6334

products with integrity

1


2

2-7/16"(61.9)

1-5/8"(41.3)

3-1/4"(82.5)

1-5/8"(41.3)

1-3/8"(34.9)

1-5/8"(41.3)

13/32"(10.3)

13/16"(20.6)

1-5/8"(41.3)

1-5/8"(41.3)

1-5/8"(41.3)

1-5/8"(41.3)

Thickness = 12 GA (2.6 mm) Thickness = 12 GA (2.6 mm)

Thickness = 12 GA (2.6 mm) Thickness = 14 GA (1.9 mm) Thickness = 12 GA (2.6 mm)



Standard Finish is mill galvanized per ASTM A-653.

See pages 5-10 for channelengineering data.

12 GA = .105"14 GA = .075"16 GA = .060"19 GA = .040"

1"(25.4)

1-5/8"(41.3)

13/16"(20.6)

1-5/8"(41.3)

13/16"(20.6)

13/16"(20.6)

7/8"(22.2)

1-5/8"(41.3)

13/16"(20.6)

1-5/8"(41.3)

N-100

N-200 N-210 N-300

N-150

N-400 N-500 N-600

N-700 N-800 N-900

NU-STRUT cHAnnels



3

A B C D

E F G H

I J K L

M N O P

Q R S T U

To order one of these channel combinations, add its letter as a suffix to a channel number.

Other combinations available upon request.Example: N-200A

NU-STRUT cHAnnel coMbinAtions


3"(76.2)

7/8" (22.2) DIA. K.O.

6"(152.4)

2"(50.8)

9/16" x 1-1/8" SLOTS(14.3 x 28.6)

2"(50.8)

2"(50.8)

2"(50.8)

3"(76.2)

13/32" x 3" SLOTS(10.3 x 76.2)

1"(25.4)

3"(76.2)

1"(25.4)

1-7/8"(47.6)

9/16" (14.3) DIA HOLES

1-7/8"(47.6)

1-7/8"(47.6)

1-7/8"(47.6)

CHANNEL WITH HOLESAdd “H” to the channel number.Example: N-200-H

CHANNEL WITH LONG SLOTSAdd “SL” to the channel number.Example: N-200-SL

CHANNEL WITH SHORT SLOTSAdd “SS” to the channel number.Example: N-200-SS

CHANNEL WITH KNOCK-OUTSAdd “KO” to the channel number.Example: N-200-KO

NU-STRUT pUncHed cHAnnel pAtteRns



4

1-5/8"(41.3)

2-7/16"(61.9)

7/8"(22.2)

3/8"(9.5)

3/8"(9.5)

1.106"(28.1)

9/32"(7.1)

.8125"(20.6)

1-5/8"(41.3)

4-7/8"(123.8)

24 610

914

48 1219

BEAM SPAN

in mm

36

152460

OR COLUMN HT.

UNIFORM

lbs kN

LOAD

Uniform Load: Load shown is total load uniformly distributed over a simple span. Stress level is 25,000 psi (172MPa) and is recommended for use where deflection is not critical.

UNIFORM LOAD

lbs kN

AT DEFLECTION= 1/240 SPAN

MAXIMUM

lbs kN

COLUMNLOAD

I = 0.525 in (21.85 cm )x-x

4 4

S = 0.394 in (6.46 cm )x-x

3 3

r = 0.850 in (2.16 cm)x-x

I = 0.339 in (14.11 cm )Y-Y

4 4

S = 0.417 in (6.83 cm )Y-Y

3 3

r = 0.683 in (1.73 cm)Y-Y

Wt. = 2.47 lbs/ft (3.67 kg/m)

Area = 0.727 in (4.69 cm )2 2

3283 14.71

9.80

1641 7.35

2188

5.881313

3283 14.71

9.80

1641 7.35

2188

5.881313

8319 37.27

31.98

5747 25.75

7139

19.294306

72 1829

2134

96 2438

84

2743108

1094 4.90

4.20

820 3.67

938

3.27729

972 4.35

3.20

546 2.45

714

1.94432

3345 14.99

12.30

2340 10.48

2746

9.152043

3048120 2.94656 1.57350 8.141817

24 610

914

48 1219

BEAM SPAN

in mm

36

152460

OR COLUMN HT.

UNIFORM

lbs kN

LOADUNIFORM LOAD

lbs kN


MAXIMUM

lbs kN

COLUMNLOAD

I = 2.830 in (117.79 cm )x-x

4 4

S = 1.161 in (19.03 cm )x-x

3 3

r = 1.395 in (35.43 cm)x-x

I = 0.678 in (28.22 cm )Y-Y4 4

S = 0.834 in (13.67 cm )Y-Y

3 3

r = 0.683 in (1.73 cm)Y-Y

Wt. = 4.94 lbs/ft (7.35 kg/m)

Area = 1.454 in (9.38 cm )2 2

3800* 17.02

17.02

3800* 17.02

3800*

17.023800*

3800* 17.02

17.02

3800* 17.02

3800*

17.023800*

18467 82.69

80.71

17383 77.88

18015

74.2316570

72 1829

2134

96 2438

84

2743108

3225 14.45

12.38

2418 10.83

2764

9.632150

3225 14.45

12.38

2418 10.83

2764

9.632150

15578 69.79

64.53

13050 58.46

14404

51.5911515

3048120 8.671935 8.451886 43.909800

For allowable concentrated load at center of span, multiply load shown by 0.5 and deflection shown by 0.8.

Uniform Load at Deflection = 1/240 Span: Load shown is total load uniformly distributed over a simple span. This load is recommended for use where deflection is required to be unnoticeable.

BEAM AND COLUMN DATA:

Maximum Column Loading: Load shown is total allowable axial load. For eccentric loads, reduce values shown accordingly.

PROPERTIES OF SECTIONS:

I = Moment of Inertia

S = Section Modulus

r = Radius of Gyration

Wt. = Weight

Area = Cross Sectional Area

* Limited by spot weld shear.

STANDARD LENGTHS:

10 ft (3.05 m) & 20 ft (6.09 m)

Thickness = 12 GA (2.6 mm) .105"


N-100A CHANNELN-100 CHANNEL

NU-STRUT enGineeRinG dAtA



5

1-5/8”(41.3)

6-1/2”(165.1)

3-1/4”(82.5)

1.50”(38.1)

.8125”(20.6)

1-5/8”(41.3)

3/8”(9.5)

3/8”(9.5)

9/32”(7.1)

1-5/8”(41.3)

3-1/4”(82.5)

1-5/8”(41.3)

.720”(18.3)

.8125”(20.6)

1-5/8”(41.3)

24 610

914

48 1219

BEAM SPAN

in mm

36

152460

OR COLUMN HT.

UNIFORM

lbs kN

LOADUNIFORM LOAD

lbs kN


MAXIMUM

lbs kN

COLUMNLOAD

I = 0.185 in (7.70 cm )x-x4 4

S = 0.204 in (3.34 cm )x-x

3 3

r = 0.576 in (14.63 cm)x-x

I = 0.234 in (9.74 cm )Y-Y

4 4

S = 0.288 in (4.72 cm )Y-Y

3 3

r = 0.647 in (16.43 cm)Y-Y

Wt. = 1.90 lbs/ft (2.83 kg/m)

Area = 0.558 in (3.60 cm )2 2

1700 7.62

5.08

850 3.81

1133

3.05680

1700 7.62

5.08

772 3.46

1133

2.21494

8370 37.50

31.45

5573 24.97

7020

19.024246

72 1829

2134

96 2438

84

2743108

566 2.54

2.17

425 1.90

485

1.69377

343 1.54

1.13

193 0.86

252

0.68152

3411 15.28

12.80

2455 11.00

2858

9.602142

3048120 1.52340 0.55123 8.471890

24 610

914

48 1219

BEAM SPAN

in mm

36

152460

OR COLUMN HT.

UNIFORM

lbs kN

LOADUNIFORM LOAD

lbs kN


MAXIMUM

lbs kN

COLUMNLOAD

I = 1.100 in (45.78 cm )x-x

4 4

S = 0.629 in (10.31 cm )x-x

3 3

r = 1.107 in (28.12 cm)x-x

I = 0.437 in (18.19 cm )Y-Y

4 4

S = 0.538 in (8.82 cm )Y-Y3 3

r = 0.698 in (17.73 cm)Y-Y

Wt. = 3.05 lbs/ft (4.54 kg/m)

Area = 0.897 in (5.79 cm )2 2

5241 23.48

15.65

2620 11.74

3494

9.392096

5241 23.48

15.65

2620 11.74

3494

9.392096

7371 33.02

29.47

5592 25.05

6579

20.114489

72 1829

2134

96 2438

84

2743108

1747 7.83

6.71

1310 5.87

1497

5.211164

1747 7.83

6.70

1145 5.13

1496

4.05905

3484 15.61

12.35

2307 10.33

2756

8.921991

3048120 4.691048 3.28733 7.871757

24 610

914

48 1219

BEAM SPAN

in mm

36

152460

OR COLUMN HT.

UNIFORM

lbs kN

LOADUNIFORM LOAD

lbs kN


MAXIMUM

lbs kN

COLUMNLOAD

I = 0.940 in (39.12 cm )x-x

4 4

S = 0.578 in (9.47 cm )x-x

3 3

r = 0.918 in (23.32 cm)x-x

I = 0.468 in (19.48 cm )Y-Y4 4

S = 0.576 in (9.44 cm )Y-Y

3 3

r = 0.647 in (16.43 cm )Y-Y

4

Wt. = 3.80 lbs/ft (5.65 kg/m)

Area = 1.116 in (7.20 cm )2 2

2480* 11.11

11.11

2408 10.79

2480*

8.631926

2480* 11.11

11.11

2408 10.79

2480*

8.631926

19047 85.33

82.24

17389 77.90

18357

72.3316146

72 1829

2134

96 2438

84

2743108

1605 7.19

6.16

1204 5.39

1376

4.791070

1605 7.19

5.72

979 4.39

1278

3.46773

14625 65.52

57.47

10755 48.18

12829

38.408571

3048120 4.31963 2.80626 31.106943

24 610

914

48 1219

BEAM SPAN

in mm

36

152460

OR COLUMN HT.

UNIFORM

lbs kN

LOADUNIFORM LOAD

lbs kN


MAXIMUM

lbs kN

COLUMNLOAD

I = 6.225 in (259.10 cm )x-x

4 4

S = 1.915 in (31.39 cm )x-x

3 3

r = 1.863 in (47.32 cm)x-x

I = 0.874 in (36.38 cm )Y-Y

4 4

S = 1.076 in (17.64 cm )Y-Y3 3

r = 0.698 in (17.73 cm)Y-Y

Wt. = 6.10 lbs/ft (9.08 kg/m)

Area = 1.794 in (11.57 cm )2 2

4900* 21.95

21.95

4900* 21.95

4900*

21.954900*

4900* 21.95

21.95

4900* 21.95

4900*

21.954900*

15930 71.37

70.22

15314 68.61

15674

66.5414852

72 1829

2134

96 2438

84

2743108

4900* 21.95

20.42

3989 17.87

4559

15.893546

4900* 21.95

20.42

3989 17.87

4559

15.893546

14288 64.01

61.02

12851 57.57

13621

53.6711979

3048120 14.303191 14.303191 49.2911003







N-150 CHANNEL N-150A CHANNEL

lbs


7/8”(22.2)

7/8”(22.2)

3/8”(9.5)

3/8”(9.5)

9/32”(7.1)




6

1-5/8"(41.3)

2-3/4"(69.8)

1-5/8"(41.3)

7/8"(22.2)

3/8"(9.5)

3/8"(9.5)

9/32"(7.1)

.595"(15.1)

.8125"(20.6)

1-3/8"(34.9)

1-5/8"(41.3)

3-1/4"(82.5)

1-5/8"(41.3)

7/8"(22.2)

3/8"(9.5)

3/8"(9.5)

9/32"(7.1)

.730"(18.5)

.8125"(20.6)

1-5/8"(41.3)

24 610

914

48 1219

BEAM SPAN

in mm

36

152460

OR COLUMN HT.

UNIFORM

lbs kN

LOADUNIFORM LOAD

lbs kN


MAXIMUM

lbs kN

COLUMNLOAD

I = 0.121 in (5.04 cm )x-x

4 4

S = 0.155 in (2.54 cm )x-x3 3

r = 0.491 in (12.47 cm)x-x

I = 0.206 in (8.57 cm )Y-Y

4 4

S = 0.254 in (4.16 cm )Y-Y

3 3

r = 0.640 in (16.26 cm)Y-Y

Wt. = 1.70 lbs/ft (2.53 kg/m)

Area = 0.502 in (3.24 cm )2 2

1291 5.78

3.86

645 2.89

861

2.31516

1291 5.78

3.86

504 2.26

861

1.44322

8193 36.70

30.80

5535 24.80

6876

19.264300

72 1829

2134

96 2438

84

2743108

430 1.93

1.65

332 1.49

369

1.29287

224 1.00

0.73

126 0.56

164

0.4499

3483 15.60

13.07

2496 11.18

2918

9.692162

3048120 1.16258 0.3680 8.031793

24 610

914

48 1219

BEAM SPAN

in mm

36

152460

OR COLUMN HT.

UNIFORM

lbs kN

LOADUNIFORM LOAD

lbs kN


MAXIMUM

lbs kN

COLUMNLOAD

I = 0.146 in (6.08 cm )x-x

4 4

S = 0.163 in (2.67 cm )x-x

3 3

r = 0.595 in (15.11 cm)x-x

I = 0.180 in (7.49 cm )Y-Y

4 4

S = 0.222 in (3.64 cm )Y-Y3 3

r = 0.661 in (16.79 cm)Y-Y

Wt. = 1.40 lbs/ft (2.08 kg/m)

Area = 0.412 in (2.66 cm )2 2

1358 6.08

4.05

679 3.04

905

2.43543

1358 6.08

4.05

608 2.72

905

1.74389

5286 23.68

20.31

3638 16.30

4534

12.132707

72 1829

2134

96 2438

84

2743108

452 2.02

1.74

339 1.52

388

1.35301

270 1.21

0.89

152 0.68

198

0.54120

2091 9.37

7.65

1447 6.48

1708

5.631257

3048120 1.21271 0.4397 4.981112

24 610

914

48 1219

BEAM SPAN

in mm

36

152460

OR COLUMN HT.

UNIFORM

lbs kN

LOADUNIFORM LOAD

lbs kN


MAXIMUM

lbs kN

COLUMNLOAD

I = 0.595 in (24.77 cm )x-x

4 4

S = 0.433 in (7.10 cm )x-x

3 3

r = 0.770 in (19.56 cm)x-x

I = 0.412 in (17.15 cm )Y-Y

4 4

S = 0.508 in (8.33 cm )Y-Y3 3

r = 0.640 in (16.26 cm)Y-Y

Wt. = 3.40 lbs/ft (5.06 kg/m)

Area = 1.004 in (6.48 cm )2 2

2150* 9.63

9.63

1804 8.08

2150*

6.461443

2150* 9.63

9.63

1804 8.08

2150*

6.461443

18275 81.87

80.44

16875 75.60

17955

69.3915489

72 1829

2134

96 2438

84

2743108

1202 5.38

4.61

902 4.04

1030

3.63811

1101 4.93

3.62

619 2.77

809

2.19489

13793 61.79

52.82

9472 42.43

11790

33.537484

3048120 3.23721 1.77396 27.166062


24 610

914

48 1219

BEAM SPAN

in mm

36

152460

OR COLUMN HT.

UNIFORM

lbs kN

LOADUNIFORM LOAD

lbs kN


MAXIMUM

lbs kN

COLUMNLOAD

I = 0.730 in (30.38 cm )x-x

4 4

S = 0.449 in (7.36 cm )x-x

3 3

r = 0.941 in (23.90 cm)x-x

I = 0.360 in (14.98 cm )Y-Y4 4

S = 0.444 in (7.28 cm )Y-Y

3 3

r = 0.661 in (16.79 cm)Y-Y

Wt. = 2.80 lbs/ft (4.17 kg/m)

Area = 0.824 in (5.31 cm )2 2

1700* 7.62

7.62

1700* 7.62

1700*

6.641483

1700* 7.62

7.62

1700* 7.62

1700*

6.641483

11890 53.27

52.38

10903 48.84

11693

46.1910310

72 1829

2134

96 2438

84

2743108

1247 5.59

4.79

935 4.19

1069

3.72831

1247 5.59

4.45

760 3.40

993

2.69600

9585 42.94

39.11

7741 34.68

8730

29.676622

3048120 3.35748 2.18486 24.295421











7

1-5/8"(41.3)

7/8"(22.2)

3/8"(9.5)

3/8"(9.5)

9/32"(7.1)

.350"(8.9)

.8125"27/64"(10.7)

(20.6)

13/16"(20.6)

1-5/8"(41.3)

1-5/8"(41.3)

1-5/8"(41.3)

1-5/8"(41.3)

24 610

914

48 1219

BEAM SPAN

in mm

36

152460

OR COLUMN HT.

UNIFORM

lbs kN

LOADUNIFORM LOAD

lbs kN


MAXIMUM

lbs kN

COLUMNLOAD

I = 0.027 in (1.12 cm )x-x

4 4

S = 0.057 in (0.93 cm )x-x3 3

r = 0.305 in (7.75 cm)x-x

I = 0.108 in (4.49 cm )Y-Y

4 4

S = 0.133 in (2.18 cm )Y-Y

3 3

r = 0.610 in (15.49 cm)Y-Y

Wt. = 0.97 lbs/ft (1.44 kg/m)

Area = 0.290 in (1.87 cm )2 2

475 2.13

1.42

237 1.06

316

0.85190

449 2.01

0.89

112 0.50

199

0.3271

4917 22.03

17.34

2432 10.89

3870

6.971557

72 1829

2134

96 2438

84

2743108

158 0.71

0.60

118 0.53

135

0.47105

49 0.22

0.16

28 0.12

36

0.1022

1080 4.84

-

- -

-

--

3048120 0.4395 0.0817 --

24 610

914

48 1219

BEAM SPAN

in mm

36

152460

OR COLUMN HT.

UNIFORM

lbs kN

LOADUNIFORM LOAD

lbs kN


MAXIMUM

lbs kN

COLUMNLOAD

I = 0.022 in (0.92 cm )x-x

4 4

S = 0.048 in (0.79 cm )x-x

3 3

r = 0.311 in (7.90 cm)x-x

I = 0.085 in (3.54 cm )Y-Y

4 4

S = 0.105 in (1.72 cm )Y-Y3 3

r = 0.613 in (15.57 cm)Y-Y

Wt. = 0.80 lbs/ft (1.19 kg/m)

Area = 0.226 in (1.46 cm )2 2

400 1.79

1.19

200 0.90

266

0.72160

336 1.50

0.73

91 0.41

162

0.2658

3930 17.61

14.40

2101 9.41

3214

6.031345

72 1829

2134

96 2438

84

2743108

133 0.60

0.51

100 0.45

114

0.3988

40 0.18

0.13

22 0.10

29

0.0818

934 4.18

-

- -

-

--

3048120 0.3680 0.0614 --

24 610

914

48 1219

BEAM SPAN

in mm

36

152460

OR COLUMN HT.

UNIFORM

lbs kN

LOADUNIFORM LOAD

lbs kN


MAXIMUM

lbs kN

COLUMNLOAD

I = 0.119 in (4.95 cm )x-x

4 4

S = 0.146 in (2.39 cm )x-x

3 3

r = 0.453 in (11.51 cm)x-x

I = 0.216 in (8.99 cm )Y-Y

4 4

S = 0.266 in (4.36 cm )Y-Y3 3

r = 0.610 in (15.49 cm )Y-Y

4

Wt. = 1.94 lbs/ft (2.89 kg/m)

Area = 0.580 in (3.74 cm )2 2

840 3.76

3.63

608 2.72

811

2.18486

840 3.76

3.63

495 2.22

811

1.42317

10921 48.93

44.70

8658 38.79

9978

31.186960

72 1829

2134

96 2438

84

2743108

405 1.81

1.55

304 1.36

347

1.21270

220 0.99

0.72

123 0.55

161

0.4397

5013 22.46

16.50

2820 12.63

3683

9.982228

3048120 1.09243 0.3579 --

24 610

914

48 1219

BEAM SPAN

in mm

36

152460

OR COLUMN HT.

UNIFORM

lbs kN

LOADUNIFORM LOAD

lbs kN


MAXIMUM

lbs kN

COLUMNLOAD

I = 0.108 in (4.49 cm )x-x

4 4

S = 0.133 in (2.18 cm )x-x

3 3

r = 0.489 in (12.42 cm)x-x

I = 0.170 in (7.08 cm )Y-Y

4 4

S = 0.210 in (3.44 cm )Y-Y3 3

r = 0.613 in (15.57 cm)Y-Y

Wt. = 1.60 lbs/ft (2.38 kg/m)

Area = 0.452 in (2.91 cm )2 2

630* 2.82

2.82

554 2.48

630*

1.98443

630* -

2.82

450 2.02

630*

1.29288

8785 39.36

36.16

7074 31.69

8072

25.945790

72 1829

2134

96 2438

84

2743108

369 1.65

1.42

277 1.24

316

1.10246

200 0.90

0.65

112 0.50

146

0.3988

4257 19.07

14.01

2394 10.73

3128

8.481892

3048120 0.99221 0.3272 6.861532







2.82

1-5/8"(41.3)

7/8"(22.2)

3/8"(9.5)

3/8"(9.5)

9/32"(7.1)

.340"(8.6).8125"

(20.6)

13/16"(20.6)






8

13/16"(20.6)

7/16"(11.1)

3/16"(4.8)

3/32"(2.4)

.406"(10.3)

.346"(8.8)

13/16"(20.6)

13/16"(20.6)

7/16"(11.1)

3/16"(4.8)

3/32"(2.4)

.406"(10.3)

.160"(4.1)

13/32"(10.3)

13/16"(20.6)

13/16"(20.6)

BEAM SPAN

in mm

OR COLUMN HT.

UNIFORM

lbs kN

LOADUNIFORM LOAD

lbs kN


MAXIMUM

lbs kN

COLUMNLOAD

I = 0.0017 in (0.07 cm )x-x

4 4

S = 0.0070 in (0.11 cm )x-x3 3

r = 0.1414 in (3.59 cm)x-x

I = 0.0077 in (0.32 cm )Y-Y

4 4

S = 0.0190 in (0.31 cm )Y-Y

3 3

r = 0.301 in (7.64 cm)Y-Y

Wt. = 0.30 lbs/ft (0.45 kg/m)

Area = 0.085 in (0.55 cm )2 2

24 610

914

48 1219

BEAM SPAN

in mm

36

152460

OR COLUMN HT.

UNIFORM

lbs kN

LOADUNIFORM LOAD

lbs kN


MAXIMUM

lbs kN

COLUMNLOAD

I = 0.0102 in (0.42 cm )x-x

4 4

S = 0.0219 in (0.14 cm )x-x

3 3

r = 0.2891 in (7.34 cm)x-x

I = 0.0134 in (0.56 cm )Y-Y

4 4

S = 0.0329 in (0.54 cm )Y-Y3 3

r = 0.3314 in (8.42 cm)Y-Y

Wt. = 0.41 lbs/ft (0.61 kg/m)

Area = 0.122 in (0.79 cm )2 2

72 1829

30512

BEAM SPAN

in mm

OR COLUMN HT.

UNIFORM

lbs kN

LOADUNIFORM LOAD

lbs kN


MAXIMUM

lbs kN

COLUMNLOAD

I = 0.0078 in (0.32 cm )x-x

4 4

S = 0.0191 in (0.31 cm )x-x

3 3

r = 0.2142 in (5.44 cm)x-x

I = 0.0154 in (0.64 cm )Y-Y

4 4

S = 0.0380 in (0.62 cm )Y-Y3 3

r = 0.301 in (7.64 cm)Y-Y

Wt. = 0.60 lbs/ft (0.89 kg/m)

Area = 0.170 in (1.10 cm )2 2

BEAM SPAN

in mm

OR COLUMN HT.

UNIFORM

lbs kN

LOADUNIFORM LOAD

lbs kN


MAXIMUM

lbs kN

COLUMNLOAD

I = 0.0498 in (2.07 cm )x-x

4 4

S = 0.0614 in (1.01 cm )x-x3 3

r = 0.4518 in (11.48 cm)x-x

I = 0.0268 in (1.11 cm )Y-Y

4 4

S = 0.0658 in (1.08 cm )Y-Y

3 3

r = 0.3314 in (8.42 cm)Y-Y

Wt. = 0.82 lbs/ft (1.22 kg/m)

Area = 0.244 in (1.57 cm )2 2





142 0.64

0.44

72 0.32

99

0.2659

48 0.21

1.30291

130 0.58

0.27

33 0.15

60

0.1022

15 0.07

1.30291

24 610

914

48 1219

36

152460

72 1829

30512

336 1.50

1.22

207 0.93

272

0.72161

138 0.62

1.54345*

336 1.50

1.21

165 0.74

270

0.46103

74 0.33

1.54345*



24 610

914

48 1219

36

152460

30512

46 0.21

0.14

23 0.10

31

0.0818

0.4293

22 0.10

0.04

6 0.03

10

0.024

0.4191

24 610

914

48 1219

36

152460

30512

127 0.57

0.38

64 0.29

85

0.2351

0.75168

101 0.45

0.21

26 0.12

46

0.0716

0.75168

13/16"(20.6)

1-5/8"(41.3)

1353 6.06

3.93

573 2.57

877

1.85414

336 1.50

8.061800

3710 16.62

15.02

2631 11.79

3352

8.471891

1326 5.94

17.583925

875 3.92

1.76

205 0.92

394

0.59131

6.391426

2594 11.62

7.97

931 4.17

1779

2.67596

13.813083






9

1-5/8"(41.3)

2"(50.8)

.8125"(10.3)

.422"(10.7)

1"(25.4)

1-5/8"(41.3)

7/8"(22.2)

3/8"(9.5)

3/8"(9.5)

9/32"(7.1)

1-5/8"(41.3)

7/8"(22.2)

3/8"(9.5)

3/8"(9.5)

9/32"(7.1)

.8125"(20.6)

.360"(9.1)

7/8"(22.2)

1-5/8"(41.3)

1-3/4"(44.4)

24 610

914

48 1219

BEAM SPAN

in mm

36

152460

OR COLUMN HT.

UNIFORM

lbs kN

LOADUNIFORM LOAD

lbs kN


MAXIMUM

lbs kN

COLUMNLOAD

I = 0.040 in (1.66 cm )x-x

4 4

S = 0.078 in (1.28 cm )x-x3 3

r = 0.316 in (8.03 cm)x-x

I = 0.148 in (6.16 cm )Y-Y

4 4

S = 0.182 in (2.98 cm )Y-Y

3 3

r = 0.608 in (15.44 cm)Y-Y

Wt. = 1.36 lbs/ft (2.02 kg/m)

Area = 0.400 in (2.58 cm )2 2

650 2.91

1.94

325 1.46

433

1.16260

642 2.88

1.33

166 0.74

296

0.47106

7858 35.20

27.77

4101 18.37

6198

11.862648

72 1829

2134

96 2438

84

2743108

216 0.97

0.83

162 0.73

185

0.64144

74 0.33

0.24

41 0.18

54

0.1432

1838 8.23

-

- -

-

--

3048120 0.58130 0.1226 --

24 610

914

48 1219

BEAM SPAN

in mm

36

152460

OR COLUMN HT.

UNIFORM

lbs kN

LOADUNIFORM LOAD

lbs kN


MAXIMUM

lbs kN

COLUMNLOAD

I = 0.053 in (2.21 cm )x-x

4 4

S = 0.092 in (1.51 cm )x-x

3 3

r = 0.352 in (8.94 cm)x-x

I = 0.160 in (1.06 cm )Y-Y

4 4

S = 0.197 in (3.23 cm )Y-Y3 3

r = 0.613 in (15.57 cm)Y-Y

Wt. = 1.44 lbs/ft (2.14 kg/m)

Area = 0.426 in (2.75 cm )2 2

766 3.43

2.29

383 1.72

511

1.37306

766 -

1.76

220 0.99

392

0.63141

7273 32.58

28.43

4684 20.98

6345

14.163160

72 1829

2134

96 2438

84

2743108

255 1.14

0.98

191 0.86

219

0.76170

98 0.44

0.32

55 0.25

72

0.1943

2195 9.83

7.22

- -

1612

--

3048120 0.68153 0.1635 --

24 610

914

48 1219

BEAM SPAN

in mm

36

152460

OR COLUMN HT.

UNIFORM

lbs kN

LOADUNIFORM LOAD

lbs kN


MAXIMUM

lbs kN

COLUMNLOAD

I = 0.180 in (7.49 cm )x-x

4 4

S = 0.206 in (3.38 cm )x-x

3 3

r = 0.474 in (12.04 cm)x-x

I = 0.296 in (12.32 cm )Y-Y

4 4

S = 0.364 in (5.97 cm )Y-Y3 3

r = 0.608 in (15.44 cm )Y-Y

4

Wt. = 2.72 lbs/ft (4.05 kg/m)

Area = 0.800 in (5.16 cm )2 2

1350 6.05

5.12

858 3.84

1144

3.07686

1350 6.05

5.12

750 3.36

1144

2.15480

17490 78.35

70.31

13558 60.74

15695

49.7111097

72 1829

2134

96 2438

84

2743108

572 2.56

2.19

429 1.92

490

1.71381

333 1.49

1.09

187 0.84

244

0.66148

8290 37.14

27.31

4668 20.91

6096

3048120 1.54343 0.54120 --

--

24 610

914

48 1219

BEAM SPAN

in mm

36

152460

OR COLUMN HT.

UNIFORM

lbs kN

LOADUNIFORM LOAD

lbs kN


MAXIMUM

lbs kN

COLUMNLOAD

I = 0.255 in (10.61 cm )x-x

4 4

S = 0.255 in (4.18 cm )x-x

3 3

r = 0.547 in (13.89 cm)x-x

I = 0.320 in (13.32 cm )Y-Y

4 4

S = 0.394 in (6.46 cm )Y-Y3 3

r = 0.613 in (15.57 cm)Y-Y

Wt. = 2.88 lbs/ft (4.28 kg/m)

Area = 0.852 in (5.49 cm )2 2

1550 6.94

6.34

1062 4.76

1416

3.81850

1550 6.94

6.34

1062 4.73

1416

3.05680

17781 79.66

72.95

14525 65.07

16284

56.0712515

72 1829

2134

96 2438

84

2743108

708 3.17

2.72

531 2.38

607

2.11472

472 2.11

1.55

265 1.19

346

0.94209

10248 45.91

34.85

5957 26.69

7780

21.094707

3048120 1.90425 0.76170 17.083812



3.43










10

CLAMPING NUT WITH LONG SPRING

CATALOG WEIGHT PER 100

7.5NUMBER lbs kg

3.4

10.0 4.5

1/4 6.3

9.5

1/2 12.7

SIZEin mm

3/8

6.3

9.5

12.7

THICKNESS

1/4in mm

3/8

1/2 12.0 5.4

THREAD

20

16

13

16.0 7.315.9

3/4 19.0

5/8 11.1

11.1

7/16

7/16 15.5 7.0

11

10

CLAMPING NUT WITH REGULAR SPRING


7.5NUMBER lbs kg

3.4

7.5 3.4

#8

#10 N/A

SIZEin mm

#10

6.3

6.3

6.3

THICKNESS

1/4in mm

1/4

1/4 7.5 3.4

THREAD

32

32

24

7.5 3.46.3

5/16 7.9

1/4 6.3

9.5

1/4

3/8 9.7 4.4

20

18

N/A

N/A

10.0 4.5

1/2 12.7

3/8 9.5

12.7

3/8

1/2 11.5 5.2

16

13

15.0 6.815.9

3/4 19.0

5/8 11.1

11.1

7/16

7/16 15.0 6.8

11

10

9.5

For N-100 and N-150 Channels

For N-200, N-210, and N-300 Channels

For N-200, N-210, and N-300 Channels

N-1-4

N-1-6N-1-8

N-1-10N-1-12

N-2-0832N-2-1032N-2-1024

N-2-4N-2-5N-2-6N-2-8

N-2-10N-2-12

in mm in mm in mm lbs kg1/4 6.3 20 7/8 22.2 5/8 15.9 8 3.6

1/4 6.3 20 1 1/8 28.6 7/8 22.2 9 4.1

1/4 6.3 20 1 3/8 34.9 1 1/8 28.6 9 4.1

5/16 7.9 18 7/8 22.2 5/8 15.9 12 5.4

5/16 7.9 18 1 1/8 28.6 7/8 22.2 12 5.4

5/16 7.9 18 1 3/8 34.9 1 1/8 28.6 13 5.9

3/8 9.5 16 7/8 22.2 5/8 15.9 13 5.9

3/8 9.5 16 1 1/8 28.6 7/8 22.2 13 5.9

3/8 9.5 16 1 3/8 34.9 1 1/8 28.6 13 5.9

3/8 9.5 16 1 5/8 41.3 1 3/8 34.9 15 6.8

3/8 9.5 16 1 7/8 47.6 1 5/8 41.3 16 7.3

3/8 9.5 16 2 1/8 54 1 7/8 47.6 16 7.3

1/2 12.7 13 7/8 22.2 1/2 12.7 14 6.4

1/2 12.7 13 1 1/8 28.6 3/4 19.0 15 6.8

1/2 12.7 13 1 3/8 34.9 1 25.4 17 7.7

1/2 12.7 13 1 5/8 41.3 1 1/4 31.7 18 8.2

1/2 12.7 13 1 7/8 47.6 1 1/2 38.1 19 8.6

1/2 12.7 13 2 1/8 54 1 3/4 44.5 20 9.1

5/8 15.9 11 1 1/8 28.6 5/8 15.9 18 8.2

5/8 15.9 11 1 3/8 34.9 7/8 22.2 20 9.1

CHANNEL STUD NUT WITH SPRINGSIZE THREAD "A" STUD "B" THREAD WEIGHT PER 100

N-2-4 NS-1N-2-4 NS-2

N-2-5 NS-1N-2-4 NS-3

N-2-6 NS-4

N-2-6 NS-3

N-2-6 NS-5

N-2-5 NS-2N-2-5 NS-3N-2-6 NS-1N-2-6 NS-2

N-2-6 NS-6

N-2-8 NS-2N-2-8 NS-3N-2-8 NS-4

N-2-8 NS-5N-2-8 NS-6N-2-8 NS-7

N-2-10 NS-2N-2-10 NS-3

CATALOGNUMBER

NU-STRUT cHAnnel nUts



11

CLAMPING NUT WITH SHORT SPRING


N-5-0832 7.5NUMBER lbs kg

3.4

7.5 3.4

#8

#10 N/A

SIZEin mm

#10

6.3

6.3

6.3

THICKNESS

1/4in mm

1/4

1/4 7.5 3.4

THREAD

32

32

24

7.5 3.46.3

5/16 7.9

1/4 6.3

9.5

1/4

3/8 8.7 3.9

20

18

N/A

N/A

9.0 4.1

1/2 12.7

3/8 9.5

9.5

3/8

3/8 8.2 3.7

16

13

9.5

CLAMPING NUT WITHOUT SPRING


6.5NUMBER lbs kg

2.9

6.5 2.9

#8

#10 N/A

SIZEin mm

#10

6.3

6.3

6.3

THICKNESS

1/4in mm

1/4

1/4 6.5 2.9

THREAD

32

32

24

6.5 2.96.3

5/16 7.9

1/4 6.3

9.5

1/4

3/8 8.7 3.9

20

18

N/A

N/A

9.0 4.1

1/2 12.7

3/8 9.5

12.7

3/8

1/2 10.6 4.8

16

13

14.0 6.315.9

3/4 19.0

5/8 11.1

11.1

7/16

7/16 14.0 6.3

11

10

9.5

1/2 12.7 9.53/8 8.5 3.913

For N-400, N-500, N-800, and N-900 Channels

Nut and bolt tightened to 50lbs. torque

For N-100, N-150, N-200, N-210, N-300, N-800, and N-900 Channels*Use with N-400 and N-500

PULL OUT AND SLIP LOAD DATA

CHANNEL

681

545

681

RESISTANCE TO SLIP

1500

1200

1500

CLAMPING

N-2-8

N-2-8

4541000N-5-8

N-2-8

NUTSAFETY FACTOR OF 3

lbs/bolt kg/boltSAFETY FACTOR OF 5

lbs/bolt kg/bolt409

272

409

900

600

900

272600

908

681

908

RESISTANCE TO PULL-OUT

2000

1500

2000

4541000

SAFETY FACTOR OF 3lbs/bolt kg/bolt

SAFETY FACTOR OF 5lbs/bolt kg/bolt

545

409

545

1200

900

1200

272600

N-5-1032

N-5-1024N-5-4N-5-5N-5-6N-5-8

N-200

N-210N-300

N-500

N-2-0832 WSN-2-1032 WSN-2-1024 WS

N-2-4 WSN-2-5 WSN-2-6 WSN-2-8 WS

N-2-10 WSN-2-12 WS*N-5-8 WS

NU-STRUT cHAnnel nUts



12

MINI NUT WITH STANDARD SPRING


1.0NUMBER lbs kg

0.5

1.0 0.5

#8 N/A

N/A

#10 N/A

SIZEin mm

#8

3.8

3.8

3.8

THICKNESS

0.150

0.150

0.150

0.150

0.150

in mm

1.0 0.5

THREAD

36

32

32

1.0 0.5N/A

1/4 6.3

#10 3.8

3.8 1.0 0.5

24

20

MINI NUT WITH SHORT SPRING


1.0NUMBER lbs kg

0.5

1.0 0.5

#8 N/A

N/A

#10 N/A

SIZEin mm

#8

3.8

3.8

3.8

THICKNESSin

0.150

0.150

0.150

0.150

0.150

mm

1.0 0.5

THREAD

36

32

32

1.0 0.5N/A

1/4 6.3

#10 3.8

3.8 1.0 0.5

24

20

NO-TWIST SQUARE WASHER


18

NUMBERBOLT SIZE HOLE SIZE

5/16 11/32in mm

7.9in mm

8.7 8.2lbs kg

183/8 7/169.5 11.1 8.2

179/1612.7 14.3 7.7

165/8 11/1615.9 17.5 7.3

1513/1619.0 20.6 6.8

1/2

3/4

N-6-0836N-6-0832N-6-1032N-6-1024

N-6-4

N-7-0836N-7-0832N-7-1032N-7-1024

N-7-4

N-1002N-1003N-1004N-1005N-1006


18

NUMBERBOLT SIZE HOLE SIZE

5/16 11/32in mm

7.9in mm

8.7 8.2lbs kg

183/8 7/169.5 11.1 8.2

179/1612.7 14.3 7.7

165/8 11/1615.9 17.5 7.3

1513/1619.0 20.6 6.8

1/2

3/4

N-1002 FN-1003 FN-1004 FN-1005 FN-1006 F

FLAT SQUARE WASHER (WITHOUT INDENT) 1-5/8"(41.3)

1-5/8"(41.3)

For N-600 Channel

For N-700 Channel

NU-STRUT flAt plAte fittinGs



13

TWO-HOLE SPLICE PLATE

CATALOG NUMBER WEIGHT PER 100

38 Lbs (17.3 Kg)

THREE-HOLE SPLICE PLATE


59 Lbs (26.8 Kg)

FOUR-HOLE SPLICE PLATE


76 Lbs (34.5 Kg)

N-1007

N-1008

N-1009


94 Lbs (42.75 Kg)N-1010

FIVE-HOLE SPLICE PLATE


35 Lbs (15.9 Kg)N-1011

TWO-HOLE SPLICE PLATE


74 Lbs (33.6 Kg)N-1012

THREE-HOLE SWIVEL PLATE


55 Lbs (25.0 Kg)N-1013

TWO-HOLE SWIVEL PLATE


73 Lbs (33.1 Kg)N-1014

FOUR-HOLE SPLICE PLATE

3-1/2"(88.9)

5-3/8"(136.5)

7-1/4"(184.1)

9-1/8"(231.8)

3-1/4"(82.6)

1-5/8"(41.3)

3-5/8"(92.1)

7-1/8"(181.0)

5-1/4"(133.4)

3-5/8"(92.1)

3-1/2"(88.9)

3-1/4"(82.6) 1-5/8"

(41.3)




14

FITTING DATA: Each fitting 1/4" thick, 15/8" wide • Holes 9/16" diameter, centered 17/8" apart, 13/16" from edge

CROSS PLATE


100 Lbs (45.4 Kg)

FOUR-HOLE CORNER PLATE

CATALOG NUMBER WEIGHT PER 100105 Lbs (47.7 Kg)


145 Lbs (65.8 Kg)



TEE PLATE


N-1021

N-1022 N-1026

N-1027N-1023

N-1024

FOUR-HOLE PLATE

FIVE-HOLE PLATE

CATALOG NUMBER WEIGHT PER 100176 Lbs (79.9 Kg)N-1028

SIX-HOLE PLATE

CATALOG NUMBER WEIGHT PER 10080 Lbs (36.3 Kg)N-1025

FOUR-HOLE FLAT CORNER PLATETHREE-HOLE FLAT CORNER PLATE

3-1/2"(88.9)

3-1/2"(88.9)

3-1/2"(88.9)

3-1/2"(88.9)

5-3/8"(136.5)

5-3/8"(136.5)

3-1/2"(88.9)

5-3/8"(136.5)

5-3/8"(136.5)

5-3/8"(136.5)

5-3/8"(136.5)

5-3/8"(136.5)

3-1/2"(88.9)

5-3/8"(136.5)

3-1/2"(88.9)

9-1/8"(231.8)




15


TWO-HOLE ADJUSTMENT ANGLE

CATALOG. NUMBER WEIGHT PER 10065 Lbs (29.5 Kg)

TWO-HOLE ADJUSTMENT ANGLE


FOUR-HOLE SHELF ANGLE



36 Lbs (16.3 Kg)

TWO-HOLE RACK CONNECTOR ANGLE


36 Lbs (16.3 Kg)

TWO-HOLE END CONNECTOR ANGLE


TWO-HOLE ADJUSTMENT ANGLE 2"


TWO-HOLE “NO-TWIST” CORNER ANGLE


N-1102

N-1103

N-1104

N-1105

N-1106

N-1107

N-1108

N-1109

TWO-HOLE ADJUSTMENT ANGLE 1-5/8"

1-5/8"(41.3)

2-1/4"(57.1)

9/16"(14.3)

1-1/2" x 9/16" SLOT(38.1 X 14.3)

2-5/8"(66.7)

1-5/8"(41.3)

2"(50.8)

1-7/8"(47.6)

4-7/8"(123.8)

2-1/2"(63.5)

2-1/2"(63.5)

1-7/8"(47.6)

2"(50.8)

2"(50.8)

9/16"(14.3)

1-1/2" x 9/16" SLOT(38.1 X 14.3)

2-5/8"(66.7)

2"(50.8)

4-1/8"(104.8)

1-5/8"(41.3)

3-1/2"(88.9)

6-7/8"(174.6)

4-1/2"(114.3)

2-1/2"(63.5)

1-7/8"(47.6)

NU-STRUT 90° AnGle fittinGs



16


FIVE-HOLE THREE-WAY SHELF ANGLE


135 Lbs (61.3 Kg)

FOUR-HOLE RACK CORNER ANGLE


FOUR-HOLE CORNER ANGLE


76 Lbs (34.5 Kg)

UNIVERSAL SHELF BRACKET


THREE-HOLE RACK CONNECTOR ANGLE


THREE-HOLE END CONNECTOR ANGLE


THREE-HOLE RACK CORNER ANGLE


THREE-HOLE SHELF ANGLE


N-1110

N-1112

N-1113

N-1115

N-1117

N-1123

N-1124

N-1125

67 Lbs (30.4 Kg)

1-5/8"(41.3)

2-1/4"(57.1)

3-1/2"(88.9)

4-1/8"(104.8)

3-1/2"(88.9)

3-1/2"(88.9)

4-1/8"(104.8)

4-1/8"(104.8)

1-7/16"(36.5)

1-7/8"(47.6)

1-7/8"(47.6)

3-7/8"(98.4)

2-1/4"(57.1)

3-1/2"(88.9)

3-7/8"(98.4)

3-3/4" (95.2)

4"(101.6)

4"(101.6)

3-1/2"(88.9)




17


THREE-HOLE BENT ANGLE RIGHT HAND


THREE-HOLE BENT ANGLE LEFT HAND



66 Lbs (29.9 Kg)N-1126 N-1135

N-1136

TWO-HOLE SLOTTED ANGLE


75 Lbs (34.1 Kg)N-1132

FOUR-HOLE TWO-WIDE CONNECTOR ANGLE


45 Lbs (20.4 Kg)N-1141

BENT ANGLE WITH STUD


80 Lbs (36.3 Kg)N-1137

FOUR-HOLE BENT ANGLETWO-HOLE TW0-SLOTTED ANGLE

CATALOGNUMBER

A

6-5/8

8-5/8

4

6

in mm168.3

219.1

WT. PER 100lbs

Bin mm

101.6kg86.2

152.4 109.8242

190N-1130N-1131

TWO-HOLE ANGLE


49NUMBER lbs

A

3in mm

76.2kg

22.2

543-1/2 88.9 24.5

614 101.6 27.7

N-1127N-1128N-1129

B A

2-5/8"(66.7)

3-7/8"(98.4)

1-1/2"(38.1)

1-5/16"(33.3)

1-1/2"(38.1)

1-1/2"(38.1)3-3/4"

(95.3)

1-7/8"(47.6)

1-7/8"(47.6)

1-7/8"(47.6)

1-7/8"(47.6)

1-5/8"(41.3) 1-5/8"

(41.3)

2-1/4"(57.2)

3-1/4"(82.6)

3-1/2"(88.9)

3-1/2"(88.9)

2"(50.8)

2"(50.8)

2"(50.8)

5-3/8"(136.5)

3/4"(19.1)

1/2" - 13 Stud

1-7/8" (47.6) 1-7/8" (47.6)

N-3463 Nut Required




18


ì Zî SUPPORTS


93NUMBER lbsCHANNEL

N-100A

A

4-7/8in mm

123.8kg

42.2

70N-150 3-1/4 82.6 31.8

67N-100 2-7/16 61.9 30.4

55N-200 1-5/8 41.3 25.0

53N-300 1-3/8 34.9 24.1

47N-500 13/16 20.6 21.3

47N-800 1 25.4 21.3

N-200A

N-400

A

EXTENDED ìZî SUPPORTS


77NUMBER lbs

A

4in mm

101.6kg

35.0

955 127.0 43.1

986 152.4 44.5

1057 177.8 47.7

1208 203.2 54.5 A

N-1209

N-1210

N-1211N-1212N-1213

N-1215

N-1218

N-1224N-1225N-1226N-1227N-1228

2-1/8"(54.0)

1-1/16"(27.0)

1-5/8"(41.3)

3-1/2"(88.9)


38 Lbs (17.2 Kg)N-1219

ìZî SUPPORTS

1/4" Offset(6.4)

NU-STRUT “z” fittinGs



19



80NUMBER lbs

A

4in mm

101.6kg

36.3

895 127.0 40.4

1016 152.4 45.8

SLOTTED “U” SUPPORTS

EXTENDED “U” SUPPORTS

CATALOGNUMBER

A

7-1/4

8-1/2

10-3/8

4-1/8

5-3/8

7-1/4

in mm184.2

215.9

263.5

WEIGHT PER 100lbs

Bin mm

104.8kg

47.7

136.5 54.5

130

120

105

184.2 59.0

1127 177.8 50.8

A

SIX-HOLE “U” SUPPORT


105 Lbs (47.7 Kg)CATALOG NUMBER WEIGHT PER 100

N-1319N-1317

N-1320N-1321N-1322

N-1324N-1325N-1326N-1327N-1328

58 Lbs (26.3 Kg)

“U” SUPPORTS


110NUMBER lbsCHANNEL

N-100

A

2-7/16in mm

61.9kg

49.9

85N-200 1-5/8 41.3 38.6

71N-500 13/16 20.6 32.2N-400

1248 203.2 56.3

A

FLAT PLATE “U” SUPPORT

N-1311

N-131284N-300 1-3/8 34.9 38.1N-1313

N-1315

128N-200A 3-1/4 82.6 58.1

76N-800 1 25.4 34.5

N-150N-1316

N-1318

7"(177.8)

3-9/32"(83.3)

5-3/8"(136.5)

5-5/16"(134.9)

1/4" (6.4) Offset

1/4" (6.4) Plate

1-7/8"(47.6)

1-5/8"(41.3)

1-1/2" (38.1)

A

B

NU-STRUT “U” fittinGs



20


TWO-HOLE SPLICE CLEVIS FOR N-500


N-1342 84 Lbs (38.1 Kg)



123 Lbs (55.8 Kg)


THREE-HOLE SPLICE CLEVIS FOR N-500

N-1343

TWO-HOLE SPLICE CLEVIS FOR N-200, N-210

N-1344

FOUR-HOLE SPLICE CLEVIS FOR N-200, N-210

N-1345

BENT “U” SUPPORT WITH STUD


N-1350 63 Lbs (28.6 Kg)



68 Lbs (30.9 Kg)


BENT “U” SUPPORT WITH HOLES

N-1360

TWO-HOLE HINGE

N-1361

FOUR-HOLE HINGE

N-1362

1-7/8"(47.6)

1-5/8"(41.3)

1-5/8"(41.3)

3/4" (19.1)

2-5/32" (54.8)

1/2"-13 Stud3-1/2"(88.9)

3-1/2"(88.9)

7-1/4"(184.1)

5-3/8"(136.5)

1/4"(6.3)

1/4" (6.3)

1/4" (6.3)

1/4"(6.3)

2-1/4"(57.2)

13/16" (20.6)

2-1/8"(54.0)

2-1/8"(54.0)

4"(101.6)

4"(101.6)

N-3463 Nut Required

NU-STRUT clevis/AnGUlAR fittinGs



21


A

A

B

C

TWO-HOLE CLOSED ANGLE


63NUMBER lbs

Akg

28.6

63 28.6

60

45

TWO-HOLE OPEN ANGLE


58NUMBER lbs

Akg

26.3

58 26.3

60

45

3-3/8 85.7

76.2

3-1/4 82.6

Bin mm

3

47.6

58.7

52.4

C

1-7/8in mm

2-5/16

2-1/1630 58 26.3

A

A

FOUR-HOLE CLOSED ANGLE


N-1413 101NUMBER lbs

Akg

45.9

101 45.9

60

45

FOUR-HOLE OPEN ANGLE


78NUMBER lbs

Akg

35.4

78 35.4

60

45

78 35.430

N-1415

N-1423N-1425N-1427

N-1443N-1445

N-1447

degrees

degrees

degrees

degrees

N-1463N-1465

4-3/8"(111.1)

3-11/16"(93.7)

3-1/2"(88.9)

3-1/2"(88.9)

5"(127.0)

2-1/2"(63.5)

NU-STRUT AnGUlAR fittinGs



22



146NUMBER lbs

A

18in mm

457.2kg

66.3

18624 609.6 84.4

22730 762.0 103.1

FLAT PLATE KNEE BRACE

TUBULAR KNEE BRACE

CATALOGNUMBER

A

12

16-5/8

18

10-1/8

13-3/8

14-3/8

in mm304.8

422.3

457.2

WEIGHT PER 100lbs

Bin mm

257.5kg

77.2

339.7 104.4

238

230

170

365.1 108.1

26736 914.4 121.2


N-1491

N-1472N-1473N-1474

24 18-5/8609.6 306473.0 138.9N-1475

N-1480N-1481N-1482N-1483

307 Lbs (139.4 Kg)

SINGLE ADJUSTABLE BRACE FITTING


N-1492 497 Lbs (225.4 Kg)

DOUBLE ADJUSTABLE BRACE FITTING

HEI

GH

T

WIDTH

N-1480

N-1481

N-1482

N-1483

A

B

1-5/8”(41.3)

B

1-5/8”(41.3)

13/16"(20.6)

1-5/8" (41.3)

1-17/32"(38.9)

1" (25.4)

17/32" (13.5) Dia. Hole

5-3/8"(136.5)

1-7/8"(47.6)

1-7/8"(47.6)

13/16"(20.6)1-1/16"

(27.0)

5-7/8" (149.2)

3-3/4"(95.3)

13/16"(20.6)

30° (.17 )min.

30° (.17 )min.

2-3/8"(60.3)

4"(101.6)

Design LoadsCompression = 1500 Lbs (680.4kg)

Tension = 300 Lbs (136.1kg)

1-7/8"(47.6)1-7/8"

(47.6)

1-1/16"(27.0)

5-7/8" (149.2)

13/16"(20.6)

13/16"(20.6)13/16"

(20.6)

13/16" (20.6)

A

NU-STRUT AnGUlAR fittinGs



23



71 Lbs (32.2 Kg)



196 Lbs (89.0 Kg)




THREE-HOLE RIGHT HAND CORNER CONNECTOR


N-1510 54 Lbs (24.5 Kg)


THREE-HOLE LEFT HAND CORNER CONNECTOR

N-1511

FOUR-HOLE CORNER CONNECTOR

N-1512

FIVE-HOLE DOUBLE WING CONNECTOR

N-1513

SIX-HOLE TRIPLE WING CONNECTOR

N-1514

EIGHT-HOLE DOUBLE CORNER CONNECTOR

N-1515

EIGHT-HOLE DOUBLE CORNER GUSSETTED CONN.

N-1516

NINE-HOLE TRIPLE WING CONNECTOR

N-1517

3-1/2"(88.9)

2"(50.8)

2"(50.8)

1-5/8"(41.3)

1-5/8"(41.3)

3-1/2"(88.9)

2"(50.8)

1-5/8"(41.3)

1-5/8"(41.3)

3-1/2"(88.9)

2"(50.8)1-7/8"

(47.6)

2"(50.8)

5-7/16"(138.1)

1-11/16"(42.9)

1-21/32"(42.1)

5-13/32"(137.3)

3-7/8"(98.4)

3-3/4"(95.2)

3-7/8"(98.4)

3-3/4"(95.2)

1-5/8"(41.3)

1-7/8" (47.6)

1-21/32"(42.1)

5-13/32" (137.3)

3-7/8"(98.4)

NU-STRUT winG fittinGs



24


SIX-HOLE DOUBLE CORNER CONNECTOR


N-1518 110 Lbs (49.9 Kg)



EIGHT-HOLE DOUBLE WING CONNECTOR

N-1519

SINGLE WING RIGHT HAND CONNECTOR

N-1520

SINGLE WING LEFT HAND CONNECTOR


N-1521 119 Lbs (54.0 Kg)



TEN-HOLE DOUBLE WING CONNECTOR

N-1522

TWELVE-HOLE DOUBLE WING CONNECTOR

N-1523

3-1/2"(88.9)

3-1/2"(88.9)

5-11/32"(135.7)

1-7/8"(47.6)

1-5/8"(41.3)

1-5/8"(41.3)

1-5/8"(41.3)1-21/32"

(42.1)

3-7/8"(98.4)

3-7/8"(98.4)

3-7/8"(98.4)

3-1/2"(88.9)

3-3/4"(95.3)

3-3/4"(95.3)

3-3/4"(95.3)

3-3/4"(95.3)

3-7/8"(98.4)

9-5/32"(232.6)

9-5/32"(232.6)




25



176 Lbs (79.9 Kg)

SINGLE WING RIGHT HAND CONNECTOR WITH GUSSET

N-1524


176 Lbs (79.9 Kg)

SINGLE WING LEFT HAND CONNECTOR WITH GUSSET

N-1525


274 Lbs (124.4 Kg)

TEN-HOLE DOUBLE WING CONNECTOR WITH GUSSET

N-1526


315 Lbs (142.9 Kg)

EIGHT-HOLE DOUBLE CORNERCONNECTOR WITH GUSSET

N-1527


310 Lbs (140.7 Kg)

TWELVE-HOLE TRIPLE WING CONNECTOR WITH GUSSET

N-1528

3-3/4" (95.3)

3-7/8"(98.4)

3-3/4" (95.3)

3-7/8"(98.4)

3-3/4"(95.3)

3-3/4"(95.3)

3-3/4"(95.3)

3-3/4"(95.3)

3-7/8"(98.4)

3-7/8"(98.4)

1-5/8"(41.3)

1-5/8" (41.3)

1-21/32"(42.1)

1-21/32" (42.1)

9-5/32"(232.6)

9-5/32"(232.6)

5-3/8"(136.5)




26


Ac

3"(76.2)

c

c

3"(76.2)

2"(50.8)

1"(25.4)

B

SHELF BRACKETS

LEFT WEIGHT PER 100

N-1601N-1603N-1605N-1607N-1609N-1611N-1613N-1615N-1617N-1619N-1621N-1623N-1625

N-1602N-1604N-1606N-1608N-1610N-1612N-1614N-1616N-1618N-1620N-1622N-1624N-1626

67HAND lbs kg

30.4

92 41.8

1-15/16 49.2

61.9

2-15/16 74.6

Bin mm

2-7/16

76.2

127.0

177.8

C

3in mm

5

7 120 54.5

6 152.4

203.2

10 254.0

Ain mm

8

RIGHTHAND

152 69.0

173 78.5

3-7/16 87.3

100.0

4-7/16 112.7

3-15/16

76.2

101.6

127.0

3

4

5 223 101.2

12 304.8

355.6

16 406.4

14

4-15/16 125.4 152.46 266 120.818 457.2

308 139.8

355 161.2

5-7/16 138.1

150.8

6-7/16 163.5

5-15/16

177.8

203.2

127.0

7

8

5 400 181.6

20 508.0

558.8

24 609.6

22

445 202.0

493 223.8

6-15/16 176.2

188.9

7-15/16 201.6

7-7/16

144.5

160.3

177.8

5-11/16

6-5/16

7 545 247.4

26 660.4

711.2

30 762.0

28

Right Hand Shown 12 GA (2.6 mm) Steel

DESIGN UNIFORM LOAD 250 Lbs (1.12 kN)

3/8" x 1" (9.5 x 25.4) SLOTTED HOLESINGLE HOLE SHOWN ON “B” LEG 7/16" (11.1) DIA.

NU-STRUT bRAcKets



27

A

CHANNEL BRACKETS


N-1631 151NUMBER lbs kg

68.6

251 114.0

5.38

2.69

N-200

1200lbs kN

600

6 152.4

304.8

Ain mm

12

351 159.4 1.79400457.218

451 204.8 1.34300

5.38

2.69

1200

600

1.79400

1.34300

609.624

CHANNEL BRACKETS


151NUMBER lbs kg

68.6

251 114.0

N-200lbs kN

6 152.4

304.8

Ain mm

12

351 159.4457.218

451 204.8609.624

CHANNEL BRACKETS


191NUMBER lbs kg

86.7

292 132.6

7.17

3.58

N-200

1600lbs kN

800

7.17

3.58

1600

800

6 152.4

304.8

Ain mm

12

CHANNEL BRACKETS


191NUMBER lbs kg

86.6

292 132.6

N-200lbs kN

6 152.4

304.8

Ain mm

12

A

N-1632N-1633N-1634

N-1635N-1636N-1637N-1638

N-1641N-1642

N-1645N-1646

2"(50.8)

1/4"(6.3)

3-5/8"(92.1)

2"(50.8)

1/4"(6.3)

3-5/8"(92.1)

1/4"(6.3)

3-1/2"(88.9)

13/16"(20.6)

1/4"(6.3)

3-1/2"(88.9)

13/16"(20.6)

When installed in the inverted position, use 60% of loads shown.




A

A

NU-STRUT bRAcKets



28


4-3/4"(120.6)7-1/2"

(190.5)5-7/8"

(149.2)

4-3/4"(120.6)

1/4"(6.3)

2"(50.8)

4-5/8"(117.5)

A

3/8"(9.5)

2"(50.8)

6-1/4"(158.7)

A

13/16"(20.6)

BRACKET FOR N-200A



CHANNEL BRACKETS


N-1647

N-1650 N-1651

436NUMBER lbs kg

197.9

536 243.3

2.60

2.01

N-200

600lbs kN

450

18 457.2

609.6

Ain mm

24

CHANNEL BRACKETS


514NUMBER lbs kg

233.4

714

8.96

5.82

N-200

2000lbs kN

1300

12 304.8

457.2

Ain mm

18

mm

415.0

1114 505.8

4.48

3.58

1000

800

609.6

762.030

91424

1314 596.6 2.9165036 914.4

CHANNEL BRACKETS


153NUMBER lbs kg

69.4

248

7.17

3.58

N-200

1600lbs kN

80012 304.8

457.2

Ain mm

18

112.6

mm

155.3

437 198.4

2.46

1.79

550

400609.6

152.46

342

24

Loading* Design Moment For 12 GA Steel13,000 in-lbs (1469 Nm)

* Applies to fitting only, not to strength of strut arm.

Safety factor 2-1/2

Loading* Design Moment For 12 GA Steel5,100 in-lbs (576 Nm)

* Applies to fitting only, not to strength of strut arm.

324.0

13/16"(20.6)

1/4"(6.3)

5-3/8"(136.5)

A

N-1652N-1653N-1654N-1655N-1656

N-1661N-1662N-1663N-1664

N-1648

BRACKET FOR N-200

NU-STRUT bRAcKets



29


4"(101.6)

1-1/16"(27.0)

1/4" Thick(6.4)

1-3/16"(30.2)

1-3/16"(30.2)

6-1/8"(155.6)

8-1/2"(215.9)

1-5/8"(41.3)

4"(101.6)

1-1/16"(27.0)

1/4" Thick(6.4)

1-3/16"(30.2)

1-3/16"(30.2)

1-5/8"(41.3)

4-3/8"(111.1)

3-3/4"(95.3)

10-1/2"(266.7)

1-1/16"(27.0)

1/4" Thick(6.4)

1-3/16"(30.2)

1-3/16"(30.2)6"

(152.4)1-5/8"(41.3)

3-1/4"(82.6) 3-1/8"

(79.4)

12-1/2"(317.5)

2-1/2"(63.5)

3-3/4"(95.3)

1-1/16"(27.0)

1/4" Thick(6.4)

1-3/16"(30.2)

1-3/16"(30.2)6"

(152.4) 1-5/8"(41.3)

3-1/8"(79.4)

2-1/2"(63.5)

5-3/4"(146.1)

5-1/4"(133.4)

16-1/2"(419.1)

1-1/16"(27.0)

1/4" Thick(6.4)

1-3/16"(30.2)

1-3/16"(30.2) 6"

(152.4)1-5/8"(41.3)

3-1/8"(79.4)

2-1/2"(63.5)

7-3/4"(196.9)

7-1/4"(184.2)

20-1/2"(520.7)

SHELF BRACKETS

CATALOGNUMBER

3.58 174 78.9

UNIF. LOAD WT PER 100

Safety Factor of 2-1/2

800Lbs LbskN Kg

VERTICAL CHANNELPART #N-200N-1669

GAUGE12

SHELF BRACKETS

CATALOGNUMBER

3.58 206 93.4



800Lbs LbskN Kg


GAUGE12

SHELF BRACKETS

CATALOGNUMBER

4.03 264 119.7



900Lbs LbskN Kg


GAUGE12

SHELF BRACKETS

CATALOGNUMBER

4.03 295 133.8



900Lbs LbskN Kg


GAUGE12

SHELF BRACKETS

CATALOGNUMBER

5.87 385 174.6



1200Lbs LbskN Kg


GAUGE12

SHELF BRACKETS

CATALOGNUMBER

2.69 459 208.2



600Lbs LbskN Kg


GAUGE12

1-1/16"(27.0)

1/4" Thick(6.4)

1-3/16"(30.2)

1-3/16"(30.2)

6"(152.4)1-5/8"

(41.3)

3-1/4"(82.6)3-1/8"

(79.4)

2-1/2"(63.5)

14-1/2"(368.3)

5-3/4"(146.1)

NU-STRUT bRAcKets



30

FITTING DATA: Each fitting 1/4" thick, 15/8" wide • Holes 9/16" diameter, centered as shown, 13/16" from edge

1-7/8"(47.6)

1/2"(12.7)

1/4" (6.3)

1-3/4"(44.4)

3/4"(19.0)

3/8" (9.5)

3-1/4"(82.5)

1-1/4"(31.7)

1/4"(6.3)

7/8"(22.2)

1-5/8"(41.3)

7/8"(22.2)

3/8"(9.5) 1-1/2"

(38.1)3-1/4"(82.5)

1"(25.4)

3/8"(9.5)

1-3/4"(44.4)

1-3/4"(44.4)

3-1/2" (88.9)1/4"(6.3)

A

OFFSET BEAM CLAMP


ONE-HOLE BEAM CLAMP


30 Lbs (13.6 Kg)

TWO-HOLE BEAM CLAMP


LIGHT DUTY BEAM CLAMP


41 Lbs (18.6 Kg)

BEAM CLAMPS


N-1702

N-1712 N-1714

N-1713 N-1715

108NUMBER lbs kg

49.0

100 45.4

3-1/2 88.9

82.5

2-11/16 68.3

Ain mm

3-1/4

41.3

34.9

20.6

CHANNEL HT.

1-5/8in mm

1-3/8

13/16 98 44.4

REC. LOAD

480lbs kN

2.15

480 2.15

480 2.15

ì U" BOLT BEAM CLAMPS


91NUMBER lbs kg

41.3

82 37.2

N-200A

CHANNEL

N-200

127.0

85.7

LENGTH OF ìU" BOLT

5in mm

3-3/8

Clamp requires: N-3409 Cap Screw & N-2-8 Clamping Nut (Order Separately)

Clamp requires: N-3411Cap Screw & N-2-8 ClampingNut (Order Separately)

1/2"-13 x 1-1/2"(12.7 x 38.1) Set Screw Included

Recommended Load 1000 Lbs (4.48 kN) when used in pairs.Recommended Load 600 Lbs (2.69 kN) when used in pairs.

Recommended Load 600 Lbs (2.69 kN) when used in pairs. Recommended Load 450 Lbs (2.02 kN) when used in pairs.

Recommended Load 480 Lbs. (2.15 kN) when used in pairs.1/2" x 1-1/2" (12.7 x 38.1) Set screw included.

Recommended Load 1,000 Lbs. (4.48 kN) when used in pairs.3/8" Dia. (9.5 mm) U-Bolt with nuts included.



Clamp requires: N-3409 Cap Screw & N-2-8 Clamping Nut (Order Separately)

N-1703N-1705

N-1708N-1709

NU-STRUT beAM clAMps



31


1-1/4"(31.7)

3/8"(9.5)

2-1/8"(54.0)

1-1/4"(31.7)3/8"

(9.5)

7/8"(22.2)

HEAVY DUTY BEAM CLAMP


60 Lbs (27.2 Kg)

THICK FLANGE BEAM CLAMP


80 Lbs (36.3 Kg)


Recommended Load 1000 Lbs (4.48 kN) when used in pairs.

1/2"-13 x 1-1/2" (12.7 x 38.1)Set Screw Included


BEAM CLAMPS


105NUMBER lbs kg

47.6

105 47.6

1/4"-20 6.3

7.9

3/8"-16 9.5

Ain mm

5/16"-18

3.2

3.2

3.2

T

1/8in mm

1/8

1/8 105 47.6

LOAD CAPACITY

800lbs kN

3.58

800 3.58

800 3.58

3/8 x 2 9.5 x 50.8

9.5 x 50.8

3/8 x 2 9.5 x 50.8

Bin mm

3/8 x 2

160 72.6

160 72.6

3/8"-16 9.5

12.7

1/2"-13 12.7

1/2"-13

4.8

4.8

6.3

3/16

3/16

1/4 200 90.7

1300 5.82

1300 5.82

1900 8.51

1/2 x 2 12.7 x 50.8

12.7 x 50.8

1/2 x 2 12.7 x 50.8

1/2 x 2

200 90.7

250 113.5

5/8"-11 15.9

15.9

3/4"-10 19.0

5/8"-11

6.3

7.9

7.9

1/4

5/16

5/16 250 113.5

1900 8.51

2800 12.54

2800 12.54

1/2 x 2 12.7 x 50.8

15.9 x 50.8

5/8 x 2 15.9 x 50.8

5/8 x 2

7/8"(22.2)

T

2-1/2"(63.5)

2-1/2"(63.5)

B 1-1/8"(28.6)

A13/16"(20.6)

1-21/32"(42.1)

T

3-5/8"(92.1)

3-1/4"(82.5)

A

BN-1721 through N-1729 N-1731 through N-1739

N-1716 N-1717

67 30.4

67 30.4

67 30.4

650 2.91

650 2.91

650 2.91

100 45.4

100 45.4

130 59.0

1100 4.93

1100 4.93

1600 7.17

130 59.0

160 72.6

160 72.6

1600 7.17

2400 10.75

2400 10.75

N-1731N-1732N-1733N-1734N-1735

N-1736N-1737N-1738N-1739

BEAM CLAMPS

CATALOG WEIGHT PER 100NUMBER lbs kg

1/4"-20 6.3

7.9

3/8"-16 9.5

Ain mm

5/16"-18

3.2

3.2

3.2

T

1/8in mm

1/8

1/8

LOAD CAPACITYlbs kN

Bin mm

3/8"-16 9.5

12.7

1/2"-13 12.7

1/2"-13

4.8

4.8

6.3

3/16

3/16

1/4

5/8"-11 15.9

15.9

3/4"-10 19.0

5/8"-11

6.3

7.9

7.9

1/4

5/16

5/16

N-1721N-1722N-1723N-1724N-1725

N-1726N-17237N-1728N-1729

3/8 x 1-1/2 9.5 x 38.1

9.5 x 38.1

3/8 x 1-1/2 9.5 x 38.1

3/8 x 1-1/2

1/2 x 1-1/2 12.7 x 38.1

12.7 x 38.1

1/2 x 1-1/2 12.7 x 38.1

1/2 x 1-1/2

1/2 x 1-1/2 12.7 x 38.1

15.9 x 38.1

5/8 x 1-1/2 15.9 x 38.1

5/8 x 1-1/2




32


COLUMN SUPPORT


STEEL C-CLAMP


N-1741 50NUMBER lbs kg

22.7

N-1742 551/2 12.7

15.9

ROD SIZE “A”in mm

5/8

25.0

mm

N-1743 29.1

9.53/8

64

ì J" BOLTS


13NUMBER lbs kg

5.9

15 6.8

152.4

254.0

SIZE

6in mm

10

Use with N-200 channel


BEAM CLAMP


33 Lbs (15.0 Kg)

SWIVEL HANGER


17 Lbs (7.7 Kg)

3/8" (9.5) Set Screw Included

ROD SIZE“A”

N-1750 N-1751

N-1755N-1756

N-1760




33


1-5/8"(41.3)

1/4"(6.3)

3-1/2"(88.9)

1-5/8"(41.3)

3-1/2"(88.9)

5"(127.0)

5"(127.0)

EIGHT-HOLE POST BASE


N-1811 288 Lbs (130.6 Kg)

FIVE-HOLE POST BASE


N-1804 116 Lbs (52.7 Kg)



N-1807 365 Lbs (165.5 Kg)



N-1805 358 Lbs (162.5 Kg)



N-1806 358 Lbs (162.5 Kg)

SEVEN-HOLE POST BASE


314 Lbs (142.6 Kg)

Holes in the base 7/16" (11.1) in Diameter

N-1813

1-11/16"(42.8)

6-1/4"(158.75)

8"(203.2)

3-1/8"(79.5)

3-1/2"(88.9)

2 HOLES 3/4" DIA.(19.05)

2 Holes11/16" DIA.

(17.5)6"

(152.4)

2"(50.8)

1"(25.4)

1"(25.4)

3-1/2"(88.9)

4"(101.6)

6"(152.4)

2"(50.8)

1"(25.4)

1"(25.4)

3-1/2"(88.9)

3-1/8"(79.4)1-11/16"

(42.9)

1-15/16"(49.2)

2 HOLES 11/16" DIA.

(17.5)

1/4"(6.3)

1/4"(6.3)

1/4"(6.3)

1/4"(6.3)

1/4"(6.3)

4"(101.6)

NU-STRUT post bAses



34


3-1/2"(88.9)

6"(152.4)

6"(152.4)

3"(76.2)

6"(152.4)

3"(76.2)

4 HOLES3/4" (19.0) DIA

3-1/2"(88.9)

1/4"(6.3)

3-5/16"(84.1)1-5/8"

(41.3)



330 Lbs (149.8 Kg)

TWELVE-HOLE POST BASE


400 Lbs (181.6 Kg)

TEN-HOLE POST BASE


392 Lbs (178.0 Kg)

TEN-HOLE POST BASE (SQUARE)


N-1814 SQ N-1816392 Lbs (178.0 Kg)

BASE PLATE

N-1814

N-1815

TWENTY-HOLE POST BASE


N-1818 550 Lbs (249.5 Kg)

4 HOLES3/4" DIA.

(19.0)

6"(152.4)

6"(152.4)

4-1/4"(107.9)

1-11/16"(42.8)

4 HOLES 3/4" DIA. (19.0)

6"(152.4)

6"(152.4)

3-1/2"(88.9)

4-1/4"(107.9)

1/4"(6.4)

3"(76.2)

3"(76.2)

3-1/2"(88.9)

1/4"(6.3)

1/4"(6.3)

1/4"(6.3)

NU-STRUT post bAses



35


END CAPS WITH KNOCK-OUTS


26NUMBER lbsCHANNEL kg

11.8

26 11.8

N-200

N-200

25 11.4

25 11.4

N-300

N-300

1/2

3/4

1/2

3/4

CONDUIT SIZEin mm

12.7

19.0

12.7

19.0

END CAP FOR N-200 CHANNEL


ECONOMY END CAPS


6NUMBER lbsCHANNEL kg

2.7

6 2.7

N-200

N-210

5 2.3

5 2.3

N-300

N-500

5 2.3N-800

SNAP CLOSURE STRIP FOR ALL

CATALOG NUMBER WEIGHT PER 100 FT.48 Lbs (21.8 Kg)

1-5/8” WIDE CHANNELS

Material: 18 GA (1.2 mm) For PL, PG & GreenStandard Finish: PL = Plain, P/G = Pregalvanized, GR = Green, WP = White Plastic, BP = Black Plastic

N-1930N-1931N-1933N-1935N-1938

N-1940N-1941N-1942N-1943

N-1920

PLASTIC END CAP FOR N-200 CHANNEL

CATALOG NUMBER WEIGHT PER 1003.4 Lbs (1.5 Kg)N-1950

N-2500 PL48 Lbs (21.8 Kg)N-2500 P/G48 Lbs (21.8 Kg)N-2500 GR7 Lbs (3.18 Kg)N-2500 WP7 Lbs (3.18 Kg)N-2500 BP

1"(25.4)

Flat head machine screw and clamp nut included.

Standard finish: White

NU-STRUT end cAps & closURe stRips



36

THINWALL CONDUIT ( EMT ) CLAMPS


9NUMBER lbs kg

4.1

11 5.0

3/8 9.5

12.7

3/4 19.0

NOMINAL SIZEin mm

1/2

12 5.4

1/4 x 3/4 6.3 x 19.0

6.3 x 19.0

1/4 x 3/4 6.3 x 19.0

SLOTTED HEX CAP SCREWin mm

1/4 x 3/4

16

16

GAGE

16

15 6.8

18 8.2

1 25.4

31.7

1-1/2 38.1

1-1/4

29 13.2

1/4 x 3/4 6.3 x 19.0

6.3 x 19.0

5/16 x 1 7.9 x 25.4

1/4 x 3/4

14

12

14

33 15.02 50.8 5/16 x 1 7.9 x 25.412

UNIVERSAL CLAMP SERIES


9NUMBER lbs kg

4.1

11 5.0

3/8 9.5

12.7

3/4 19.0

NOMINAL SIZEin mm

1/2

12 5.4

5/16 x 1-1/4 7.9 x 31.7

7.9 x 31.7

5/16 x 1-1/4 7.9 x 31.7


5/16 x 1-1/4

16

16

GAGE

16

15 6.8

18 8.2

1 25.4

31.7

1-1/2 38.1

1-1/4

29 13.1

5/16 x 1-1/4 7.9 x 31.7

7.9 x 31.7

5/16 x 1-1/4 7.9 x 31.7

5/16 x 1-1/4

14

14

14

33 15.02 50.8 5/16 x 1-1/4 7.9 x 31.714

RIGID CONDUIT OR PIPE CLAMPS


10NUMBER lbs kg

4.5

11 5.0

3/8 9.5

12.7

3/4 19.0

NOMINAL SIZEin mm

1/2

15 6.8

1/4 x 3/4 6.3 x 19.0

6.3 x 19.0

1/4 x 3/4 6.3 x 19.0


1/4 x 3/4

16

14

GAGE

16

17 7.7

19 8.6

1 25.4

31.7

1-1/2 38.1

1-1/4

29 13.2

1/4 x 3/4 6.3 x 19.0

6.3 x 19.0

5/16 x 1 7.9 x 25.4

1/4 x 3/4

14

12

14

34 15.42 50.8 5/16 x 1 7.9 x 25.412

40 18.2

47 21.3

2-1/2 63.5

76.2

3-1/2 88.9

3

62 28.1

5/16 x 1 7.9 x 25.4

7.9 x 25.4

3/8 x 1 9.5 x 25.4

5/16 x 1

12

11

12

67 30.4

80 36.3

4 101.6

127.0

6 152.4

5

102 46.3

3/8 x 1-1/4 9.5 x 31.7

9.5 x 31.7

3/8 x 1-1/4 9.5 x 31.7

3/8 x 1-1/4

11

10

11

116 52.78 203.2 3/8 x 1-1/4 9.5 x 31.710

Includes Slotted Indented Hex Head Cap Screw and Kep Nut.



N-2025

N-2026

N-2028N-2030

N-2032N-2034

N-2038

N-2055

N-2056

N-2058N-2060

N-2062N-2064

N-2068

N-2125

N-2126N-2128N-2130N-2132N-2134

N-2138N-2142N-2146N-2150

N-2154N-2162N-2170N-2174

NU-STRUT pipe clAMps



37

O.D. TUBING CLAMPS


8NUMBER lbs kg

3.6

8 3.6

1/4 6.3

9.5

1/2 12.7

NOMINAL SIZEin mm

3/8

9 4.1

1/4 x 3/4 6.3 x 19.0

6.3 x 19.0

1/4 x 3/4 6.3 x 19.0


1/4 x 3/4

16

16

GAGE

16

10 4.5

11 5.0

5/8 15.9

19.0

7/8 22.2

3/4

12 5.4

1/4 x 3/4 6.3 x 19.0

6.3 x 19.0

1/4 x 3/4 6.3 x 19.0

1/4 x 3/4

16

16

16

14 6.425.4 1/4 x 3/4 6.3 x 19.014

15 6.8

16 7.3

1-1/8 28.6

31.7

1-3/8 34.9

1-1/4

17 7.7

1/4 x 3/4 6.3 x 19.0

6.3 x 19.0

1/4 x 3/4 6.3 x 19.0

1/4 x 3/4

14

14

14

18 8.2

19 8.6

1-1/2 38.1

41.3

1-3/4 44.4

1-5/8

28 12.7

1/4 x 3/4 6.3 x 19.0

6.3 x 19.0

5/16 x 1 7.9 x 25.4

1/4 x 3/4

14

12

14

29 13.21-7/8 47.6 5/16 x 1 7.9 x 25.412

1

31 14.150.8 5/16 x 1 7.9 x 25.412

32 14.5

33 15.0

2-1/8 54.0

57.1

2-3/8 60.3

2-1/4

34 15.4

5/16 x 1 7.9 x 25.4

7.9 x 25.4

5/16 x 1 7.9 x 25.4

5/16 x 1

12

12

12

35 15.9

37 16.8

2-1/2 63.5

66.7

2-3/4 69.9

2-5/8

38 17.3

5/16 x 1 7.9 x 25.4

7.9 x 25.4

5/16 x 1 7.9 x 25.4

5/16 x 1

12

12

12

40 18.22-7/8 73.0 5/16 x 1 7.9 x 25.412

2

41 18.676.2 5/16 x 1 7.9 x 25.412

43 19.5

45 20.4

3-1/8 79.4

82.6

3-3/8 85.7

3-1/4

46 20.9

5/16 x 1 7.9 x 25.4

7.9 x 25.4

5/16 x 1 7.9 x 25.4

5/16 x 1

12

12

12

47 21.3

56 25.4

3-1/2 88.9

92.1

3-3/4 95.3

3-5/8

58 26.3

5/16 x 1 7.9 x 25.4

9.5 x 31.7

3/8 x 1-1/4 9.5 x 31.7

3/8 x 1-1/4

12

11

11

60 27.23-7/8 98.4 3/8 x 1-1/4 9.5 x 31.711

3

62 28.1101.6 3/8 x 1-1/4 9.5 x 31.711

62 28.1

64 29.1

4-1/8 104.8

108.0

4-3/8 111.1

4-1/4

66 30.0

3/8 x 1-1/4 9.5 x 31.7

9.5 x 31.7

3/8 x 1-1/4 9.5 x 31.7

3/8 x 1-1/4

11

11

11

67 30.4

70 31.7

4-1/2 114.3

117.5

4-3/4 120.6

4-5/8

72 32.7

3/8 x 1-1/4 9.5 x 31.7

9.5 x 31.7

3/8 x 1-1/4 9.5 x 31.7

3/8 x 1-1/4

11

11

11

73 33.14-7/8 123.8 3/8 x 1-1/4 9.5 x 31.711

4

74 33.6127.0 3/8 x 1-1/4 9.5 x 31.711

76 34.5

77 35.0

5-1/8 130.2

133.3

5-3/8 136.5

5-1/4

78 35.4

3/8 x 1-1/4 9.5 x 31.7

9.5 x 31.7

3/8 x 1-1/4 9.5 x 31.7

3/8 x 1-1/4

11

11

11

79 35.85-1/2 139.7 3/8 x 1-1/4 9.5 x 31.711

5

88 40.0142.9

5-3/4 146.0

5-5/8

90 40.9

9.5 x 31.7

3/8 x 1-1/4 9.5 x 31.7

3/8 x 1-1/4

10

10

92 41.85-7/8 149.2 3/8 x 1-1/4 9.5 x 31.710

92 41.8152.4 3/8 x 1-1/4 9.5 x 31.7106

8

10

203.2 112 50.8 3/8 x 1-1/4 9.5 x 31.710

139 63.0254 3/8 x 1-1/4 9.5 x 31.710

161 73.0304.8 3/8 x 1-1/4 9.5 x 31.71012

Includes Slotted Hex Head Cap Screw and Kep Nut.

N-2224N-2225N-2226

N-2227N-2228N-2229N-2230N-2231N-2232

N-2233N-2234N-2235N-2034N-2237

N-2238N-2239

N-2240N-2138N-2242

N-2243N-2244N-2142N-2246N-2247N-2248

N-2249N-2146N-2251N-2252N-2253N-2150

N-2255N-2256N-2257N-2154N-2259N-2260

N-2261N-2262N-2263N-2264N-2265N-2266

N-2267N-2268N-2269N-2270N-2274N-2278N-2280

NU-STRUT pipe clAMps



38

STUD SPLICE PLATE


TAPPED SPLICE PLATE


HANGER


25NUMBER lbsDESCRIPTION

CHANNEL HANGER

HOLE SIZE

17/32in mm

13.5kg

11.3

27FIXTURE HANGER 17/32 13.5 12.2

HANGER


45NUMBER lbsDESCRIPTION

CHANNEL HANGER

HOLE SIZE

17/32in mm

13.5kg

20.4

47FIXTURE HANGER 17/32 13.5 21.3

FOUR-HOLE SPLICE CLEVIS


100

NUMBER lbsN-200

A

1-5/8

in mm

41.3

kg

45.4

95N-300 1-3/8 34.9 43.1

CHANNELSIZE

80N-500 13/16 20.6 36.3

N-210

For All Single Channels and N-500A

*With 1/4” x 3/4” (6.3 x 19.0) Stud and Wing Nut

*With 1/4” x 3/4” (6.3 x 19.0) Stud and Wing Nut

For N-200A, N-210A, and N-300A Channels

Material : 14GA (1.9 mm)Should be used with either N-2439 or N-2440

Material: 14GA (1.9 mm)Material: 14GA (1.9 mm)Includes 4 pieces 1/4”-20 (6.3) Flat Head Machine Screws

10 Lbs (4.5 Kg)

N-2420N-2422*

N-2424N-2426*

N-2432

N-2433N-2435

N-2440N-2439

A

NU-STRUT electRicAl AccessoRies



39

1-1/2"(38.1)

1-3/8"(34.9)

1/32"(0.8)

1-21/32"(42.1)

6-1/4"(158.7)

9/32" (7.1) DIA HOLES

FIXTURE STUD NUT


KNOCK-OUT PLATE


35 Lbs (15.9 Kg)

SHOULDER BOLT


WIRING STUD CAST ALUMINUM


8 Lbs (3.6 Kg)

FIXTURE NUT


FIBER WIRE RETAINER


CONDUIT CONNECTOR


N-2442 28NUMBER lbsUSE WITH

1/2" (12.7) CONDUIT

HOLE SIZE

7/8in mm

22.2kg

12.7

283/4" (19.0) CONDUIT 1-3/32 27.8 12.7

Assembly includes nuts and flat-head machine screws

Diameter: 3/8" (9.5)

1-1/4"(31.7)

TAPPED FOR1/4"-20 (6.3)SCREW

1/2" (12.7) PIPE

THREADS

1-1/8"(28.6)

2"(50.8)

N-2443

N-2449 N-2462

N-2460 N-2463

N-2461 N-2469

NU-STRUT electRicAl AccessoRies



40

1-5/8"(41.3)

9/16" (14.3)

Allowable load 300 lbs (1.48 kN) maximum.Trolley designed to fit N-200 and N-210 channels.

TWO WHEEL TROLLEY


59 Lbs (26.8 Kg)

3-1/2"(88.9)

H

CATALOG WEIGHT

1.06NUMBER lbs

“H”

9/16in mm

14.3kg0.5

0.991-1/8 28.6 0.4

Allowable load 600 lbs (2.67 kN) maximum.Trolley designed to fit N-200 and N-210 channels.

THREADED ROD


12NUMBER lbs kg

5.4

30 13.6

1/4 6.3

9.5

1/2 12.7

DIA. SIZEin mm

3/8

52 23.6

THREAD

20

16

13

85 38.615.95/8 11

ROD COUPLERS


2NUMBER lbs kg

0.9

2 0.9

1/4 6.3

7.9

3/8 9.5

DIA. SIZEin mm

5/16

22.2

22.2

44.4

“A” LENGTH

7/8in mm

7/8

1-3/4 11 5.0

THREAD

20

18

16

11 5.012.7

5/8 15.9

1/2 44.4

54.0

1-3/4

2-1/8 16 7.3

13

11

3/4 19.0 57.12-1/4 28 12.710

A

N-2600

N-2601

N-2602

CHANNEL TROLLEY SUPPORT


102 Lbs (46.3 Kg)N-2611

CHANNEL TROLLEY SUPPORT

FOUR WHEEL TROLLEY


220 Lbs (99.9 Kg)N-2612

N-2650

N-2652N-2654N-2656

123 55.819.13/4 10N-2658

N-2660N-2662N-2664N-2666N-2668N-2670

Requires 3/8" x 2-1/2" Bolt and 3/8" Nut (Not Included)

Requires 3/8" x 2-1/2" Bolt and 3/8" Nut (Not Included)

1-5/8"(41.3)

1"(25.4)

2 HOLES7/16" DIA.

(11.1)

1 HOLE9/16" DIA.

(14.3)

3-3/4"(9.53)

3-1/2"(88.9)

1"(25.4)

2 HOLES7/16" DIA.

(11.1)

1 HOLE 9/16" DIA.(14.3)

3-3/4"(9.53)

Standard Length is 10'-0"Electro-Galvanized Finish

Design load 2500 lbs (1139.0 Kg)

Design load 1200 lbs (549.3 Kg)

NU-STRUT tRollies And sUppoRts



41

2-1/4"(57.1)

A

1-5/8"(41.3)

HOLE SIZE

A

B

B

1-5/8"(41.3)

A

A

PORCELAIN CABLE SADDLES

CATALOG WEIGHT PER 100NUMBER lbs

“A” LENGTHin mm kg

1044 101.6 47.2

MAXIMUM CABLE DIA.

3in mm

76.2

4-1/2 114.3

N-2708N-2709

733 76.2 33.1

MAPLE CABLE SADDLES



403-1/2 88.9 18.1

HOLE SIZE (CABLE DIA.)

0 - 1in mm

0 - 25.4

1 - 1-1/2 25.4 - 38.1

303 76.2 13.6

“B” LENGTHin mm

2 50.8

1-3/4 44.4

704-1/2 114.3 31.7

1-1/2 - 2 38.1 - 50.8

2 - 2-1/2 50.8 - 63.5

504 101.6 22.7

3-1/2 88.9

2-1/4 57.1

1005-1/2 139.7 45.4

2-1/2 - 3 63.5 - 76.2

3 - 3-1/2 76.2 - 88.9

805 127.0 36.3

3 76.2

2-3/4 69.8

1607 177.8 72.6

3-1/2 - 4 88.9 - 101.6

4 - 4-1/2 101.6 - 114.3

1306 152.4 59.0

3-3/4 95.2

3-1/4 82.5

SQUARE MAPLE CABLE CLAMPS



884 101.6 40.0

HOLE SIZE

0 - 1in mm

0 - 25.4

1 - 1-1/2 25.4 - 38.1

683-1/2 88.9 30.9

“B” LENGTHin mm

4 101.6

3-1/2 88.9

1465-1/2 139.7 66.3

1-1/2 - 2 38.1 - 50.8

2 - 2-1/2 50.8 - 63.5

1064-1/2 114.3 48.1

5-1/2 139.7

4-1/2 114.3

2236-1/2

7-1/2

165.1 101.2

2-1/2 - 3 63.5 - 76.2

3 - 3-1/2 76.2 - 88.9

1886 152.4 85.4

6-1/2 165.1

6 152.4

276190.5 125.3

3-1/2 - 4 88.9 - 101.6

4 - 4-1/2 101.6 - 114.3

2597 177.8 117.6

7-1/2 190.5

7 177.8

MAPLE CABLE CLAMPS



431-1/2 38.1 19.5

HOLE SIZE

0 - 5/8in mm

0 - 15.9

1/2 - 1 12.7 - 25.4

241 25.4 10.9

PIPE CLAMPINCLUDED

N-2134

N-2130

662-1/2 63.5 30.0

3/4 - 1-1/2 19.0 - 38.1

1-1/4 - 1-3/4 31.7 - 44.4

542 50.8 24.5

N-2142

N-2138

1083-1/2 88.9 49.0

1-1/2 - 2-1/4 38.1 - 57.1

2 - 2-1/2 50.8 - 63.5

853 76.2 38.6

N-2150

N-2146

1635 127.0 74.0

2-1/4 - 3 57.1 - 76.2

3 - 4 76.2 - 101.6

1234 101.6 55.8

N-2162

N-2154

3/8”-16x63/8”-16x6

3/8”-16x8

3/8”-16x7

3/8”-16x9

3/8”-16x8

3/8”-16x10

3/8”-16x9

STUDSIZE

N-2810

N-2811

N-2812N-2813

N-2814N-2815

N-2816N-2817

N-2820

N-2821

N-2822N-2823

N-2824N-2825

N-2826N-2827

N-2870

N-2871

N-2872N-2873

N-2874N-2875

N-2876N-2877

Furnished with 2 studs, 2 hex nuts, 2 flat washers. Requires two 3/8" clamping nuts. Maple hardwood parafin impregnated. Order separately. Orders must specify exact hole size.

Maple Cable Clamps are furnished complete with pipe clamp and hardware.

Furnished with 2 studs, 2 hex nuts, 2 flat washers. Requires two 3/8" clamping nuts. Maple hardwood parafin impregnated. Order separately. Orders must specify exact hole size.

NU-STRUT sAddles And MAple clAMps



42

SWIVEL HANGER ( FEMALE )


15NUMBER lbs kg

6.8

29 13.2

THREAD

16

13

3/8 9.5

12.7

HOLE SIZEin mm

1/2

SWIVEL HANGER ( MALE )


20NUMBER lbs kg

9.1

38 17.3

THREAD

16

13

3/8 9.5

12.7

STUD SIZEin mm

1/2

SWIVEL HANGER ( FEMALE-FEMALE )


30NUMBER lbs kg

13.6

58 26.3

THREAD

16

13

3/8 9.5

12.7

HOLE SIZEin mm

1/2

SWIVEL HANGER ( MALE-FEMALE )


35NUMBER lbs kg

15.9

67 30.4

THREAD

16

13

3/8 9.5

12.7

STUD SIZEin mm

1/2

1-3/4"(44.4)

3/8"(9.5)

3/8"(9.5)

1-3/4"(44.4)

1"(25.4)

3/8"(9.5)

2-3/4"(69.8)

3/8"(9.5)

2-3/4"(69.8)

1"(25.4)

N-2905

N-2906

N-2910

N-2911

N-2915

N-2916

N-2920

N-2921

NU-STRUT swivel HAnGeRs



43

2"(50.8)

3-5/8"(92.1)

1-5/8"(41.3)

12 GA

SPOT INSERT


N-3000 50 Lbs (22.7 Kg)

Design Load 600 Lbs (2.69kN) Safety Factor of 5

CONCRETE INSERT NUTS


8NUMBER lbs kg

3.6

11 5.0

1/4"-20 6.3

9.5

TAPPED SIZEin mm

3/8"-16

15 6.8

19 8.6

1/2"-13 12.7

15.95/8"-11

17 7.7

15 6.8

3/4"-10 19.0

22.27/8"-9

CONCRETE INSERT


88NUMBER lbs kg

39.9

120 54.4

DESIGN LOAD

800

1000

4 101.6

152.4

LENGTHin mm

6

3.58

4.48

lbs kN

CONTINUOUS CONCRETE INSERT


213NUMBER lbs kg

96.5

280 126.8

12 304.8

406.4

Ain mm

16

347 157.2

414 187.5

20 508.0

609.624

548 248.2

615 278.6

32 812.8

914.436

682 308.940 1016.0

816 369.6

1017 460.7

48 1219.2

1524.060

1218 551.8

1419 642.8

72 1828.8

2133.684

1620 733.9

1821 824.9

96 2438.4

2743.2

2022 916.0120 3048.0

2424 1098.1

2826 1280.2

144 3657.6

4267.2168

3228 1464.2

3630 1646.5

192 4876.8

5486.4216

4032 1828.9240 6096.0

Use N-1952 End Cap.

Loads concentrated within the last 2" (50.8) of concrete inserts8" (203.2) and longer should not exceed 1000 lbs (4.48 kN).

Concrete insert should be secured to the forms on 16" (406.4)to 24" (609.6) intervals.

N-3270 Continuous Concrete Inserts are made from N-200channel. Use channel nuts designed for use in N-200 channel.

Styrofoam fillers are supplied with all concrete inserts.

Use N-1930 End Cap.

108

End CapN-1952

12 GA = 2.6 mm

Electro-Galvanized Finish

Electro-Galvanized FinishN-3024N-3025N-3026N-3027N-3028N-3029

N-3250

N-3251152 68.9 1200203.28 5.38N-3252

N-3253N-3254N-3255N-3256N-3257

N-3257AN-3258N-3259N-3260N-3261N-3262N-3263N-3264N-3265N-3266N-3267N-3268N-3269N-3270

4"(101.6)

4"(101.6)

1-5/8"(41.3)

Design load for N-3253 through N-3270 is 2000 lbs (8.96 kN)per foot with a safety factor of 3 in average good concrete.

NU-STRUT concRete inseRts/n-200



44

4"(101.6)

4"(101.6)

1-3/8"(34.9)

CONCRETE INSERT


95NUMBER lbs kg

43.1

128 58.1

DESIGN LOAD

800

1000

4 101.6

152.4

LENGTHin mm

6

3.58

4.48

lbs kN



202NUMBER lbs kg

262

12 304.8

406.4

Ain mm

16

316

376

20 508.0

609.624

496

556

32 812.8

914.436

61640 1016.0

736

915

48 1219.2

1524.060

1095

1274

72 1828.8

2133.684

1453

1633

96 2438.4

2743.2

1813120 3048.0

2173

2533

144 3657.6

4267.2168

2893

3253

192 4876.8

5486.4216

3613240 6096.0

Use N-1953 End Cap.






Use N-1933 End Cap.

108

End CapN-1953

N-3350

N-3351155 70.3 1200203.28 5.38N-3352

N-3353N-3354N-3355N-3356N-3357


91.7

118.9

143.5

170.7

225.2

252.4

279.7

333.8

415.4

497.1

577.9

659.7

740.7

822.4

985.7

1148.9

1312.2

1475.5

1638.8




45

4"(101.6)

4"(101.6)

13/16"(20.6)

CONCRETE INSERT


31NUMBER lbs kg

14.0

47 21.3

DESIGN LOAD

400

600

4 101.6

152.4

LENGTHin mm

6

1.79

2.69

lbs kN



117NUMBER lbs kg

153

12 304.8

406.4

Ain mm

16

188

224

20 508.0

609.624

295

331

32 812.8

914.436

36740 1016.0

438

545

48 1219.2

1524.060

652

759

72 1828.8

2133.684

866

973

96 2438.4

2743.2

1080120 3048.0

1294

1508

144 3657.6

4267.2168

1722

1936

192 4876.8

5486.4216

2150240 6096.0

Use N-1953 Modified End Cap.






Use N-1935 End Cap.

108

End CapN-1953 Modified

N-3550

N-355162 28.1 800203.28 3.58N-3552

N-3553N-3554N-3555N-3556N-3557


53.0

69.3

85.2

101.5

133.6

149.9

166.3

198.4

247.2

295.4

344.3

392.3

441.3

489.2

586.2

684.0

781.1

878.2

975.2




46

4"(101.6)

4"(101.6)

7/8"(22.2)

CONCRETE INSERT


81NUMBER lbs kg

36.7

102 46.3

DESIGN LOAD

500

750

4 101.6

152.4

LENGTHin mm

6

2.24

3.36

lbs kN



156NUMBER lbs kg

205

12 304.8

406.4

Ain mm

16

253

302

20 508.0

609.624

399

448

32 812.8

914.436

49740 1016.0

594

740

48 1219.2

1524.060

886

1032

72 1828.8

2133.684

1178

1324

96 2438.4

2743.2

1470120 3048.0

1762

2054

144 3657.6

4267.2168

2346

2638

192 4876.8

5486.4216

2930240 6096.0

Use N-1953 Modified End Cap.






Use N-1935 End Cap.

108

End CapN-1953 Modified

N-3950

N-3951122 55.3 1000203.28 4.48N-3952

N-3953N-3954N-3955N-3956N-3957


70.7

92.9

114.6

137.0

181.0

203.2

225.1

269.1

335.2

401.4

468.1

534.3

600.6

666.8

799.2

931.7

1064.1

1196.6

1329.0




47

HEX HEAD CAP SCREWS


1.0NUMBER lbs kg

0.5

1.3 0.6

1/4 6.3

6.3

1/4 6.3

DIAMETERin mm

1/4

12.7

19.1

25.4

LENGTH

1/2in mm

3/4

1 1.7 0.8

4.0 1.89.5

3/8 9.5

3/8 19.0

25.4

3/4

1

25.41

4.5 2.0

5.3 2.4

6.1 2.8

3/8 9.5

9.5

3/8 9.5

3/8

31.7

38.1

50.8

1-1/4

1-1/2

2 7.6 3.5

8.5 3.99.5

1/2 12.7

3/8 57.12-1/4

9.1

4.5

1/2 12.7

31.71-1/4 10.0

5.311.6

6.013.2

6.7

1/2 12.7

12.7

1/2 12.7

1/2

38.1

44.4

50.8

1-1/2

1-3/4

2 14.7

7.316.0

17.5 7.912.71/2

57.1

63.52-1/2

2-1/4

FLAT HEAD MACHINE SCREWS


1.2NUMBER lbs kg

0.51/4 6.3

5/16 7.9

DIAMETERin mm

15.9

25.4

LENGTH

5/8in mm

1

2

2.6 1.2

6.5 3.09.5

3/8 9.5

3/8 50.8

57.12-1/4 7.1 3.2

ROUND HEAD MACHINE SCREWS


1.2NUMBER lbs kg

0.5

1.5 0.7

1/4 6.3

6.3

1/4 6.3

DIAMETERin mm

1/4

19.0

25.4

31.7

LENGTH

3/4in mm

1

1-1/4 1.8 0.8

2.6 1.27.9

5/16 7.9

5/16 25.4

31.7

1

1-1/4 3.0 1.4

3.6 1.6

4.1 1.9

5/16 7.9

9.5

3/8 9.5

3/8

38.1

25.4

31.7

1-1/2

1

1-1/4 4.7 2.1

5.3 2.49.5

3/8 9.5

3/8 38.1

63.5

1-1/2

2-1/2 7.7 3.5

1/2 12.7 4.1

N-3400

N-3401

N-3402N-3403N-3404

N-3405N-3406N-3407N-3408

N-3409

N-3410N-3411N-3412

N-3413N-3414N-3415

20.6 9.312.71/2 76.23N-341623.8 10.812.71/2 88.93-1/2N-341727.1 12.312.71/2 101.64N-3418

N-3420N-3421N-3422N-3423

3/8 9.5 63.52-1/2 7.7 3.5N-342412.7 19.13/4

1

8.1 3.7

9.2 4.212.7

1/2 12.7

1/2

1/2

25.4

31.81-1/4 10.3 4.7

N-3425N-3426N-3427

1/2 12.7 38.11-1/2 11.6 5.3N-3428

N-3470N-3471N-3472N-3473N-3474N-3475N-3476N-3477N-3478N-3479

NU-STRUT HARdwARe



48

SPLIT LOCK WASHERS


0.3NUMBER lbs kg

0.1

0.7 0.3

1/4 6.3

9.5

1/2 12.7

SIZEin mm

3/8

1.5 0.7

2.6 1.215.95/8

N-3430

N-3431N-3432

N-3433

FLAT WASHERS


0.7NUMBER lbs kg

0.3

1.5 0.7

1/4 6.3

9.5

1/2 12.7

SIZEin mm

3/8

3.5 1.6

7.7 3.515.95/8

N-3440N-3441N-3442N-3443

FENDER WASHERS


2.0NUMBER lbs kg

0.9

3.0 1.4

1/4 x 1-1/4 6.3 x 31.7

9.5 x 38.1

SIZEin mm

3/8 x 1-1/2N-3450N-3451

4.5 2.012.7 x 38.11/2 x 1-1/2N-3452

HEX NUTS


0.6NUMBER lbs kg

0.3

1.2 0.5

1/4 6.3

7.9

3/8 9.5

SIZEin mm

5/16

1.6 0.7

4.8 2.212.71/2

7.33 3.315.95/8

N-3460N-3461N-3462N-3463N-3464

KEP NUTS


0.9NUMBER lbs kg

0.4

1.6 0.7

1/4 6.3

7.9

3/8 9.5

SIZEin mm

5/16

2.7 1.2

N-3490

N-3491

N-3492

NU-STRUT HARdwARe



49

“T”

“C”

1-5/8"(41.3)

ONE-HOLE O.D. TUBING CLAMPS


4NUMBER lbs kg

1.8

5 2.3

1/4 6.3

7.9

O.D. TUBE SIZEin mm

5/16

5 2.3

6 2.7

3/8 9.5

12.71/2

8 3.6

9 4.1

5/8 15.9

19.03/4

10 4.5

11 5.0

7/8

25.41

22.2

“A”HOLE DIA.

5/16" DIA. HOLE

N-3724N-3724A

N-3725N-3726N-3727N-3728N-3729

N-3730

STANDARD PIPE STRAP


24NUMBER lbs kg

10.9

28 12.7

1/2 12.7

19.0

PIPE SIZEin mm

3/4

32 14.5

35 15.9

1 25.4

31.71-1/4

40 18.2

95 43.1

1-1/2 38.1

50.82

116 52.7

135 61.3

2-1/2

76.23

63.5

3 76.2

82.6

“C” LENGTHin mm

3-1/4

3-9/16 90.5

96.83-13/16

4-1/16 103.2

147.65-13/16

6-1/4

177.87

158.7

1/8 3.2

3.2

“T” THICKNESSin mm

1/8

1/8 3.2

3.21/8

1/8 3.2

6.31/4

1/4

6.31/4

6.3

9/32 7.1

7.1

“A” HOLE SIZEin mm

9/32

9/32 7.1

7.19/32

9/32 7.1

11.17/16

7/16

11.17/16

11.1

155 70.4

180 81.7

3-1/2 88.9

101.64

195 88.5

240 109.0

5

152.46

127.0

7-7/8 200.0

203.28

9-1/8

261.910-5/16

231.8

1/4 6.3

6.31/4

1/4

6.31/4

6.3

7/16 11.1

11.17/16

7/16

11.17/16

11.1

N-3826N-3828N-3830N-3832N-3834N-3838N-3842N-3846N-3850N-3854N-3862N-3870

Requires one 1/4" Dia. spring nut and one 1/4"-20 machine screw (order separately)

Requires two spring nuts and two machine screws (order separately)

NU-STRUT tUbinG clAMps & pipe stRAps



50

N-100 ..................2, 5N-150 ..................2, 6N-200 ..................2, 6N-210 ..................2, 7N-300 ..................2, 7N-400 ..................2, 8N-500 ..................2, 8N-600 ..................2, 9N-700 ..................2, 9N-800 ................2, 10N-900 ................2, 10N-1002 ..................13N-1003 ..................13N-1004 ..................13N-1005 ..................13N-1006 ..................13N-1002 F ..............13N-1003 F ..............13N-1004 F ..............13N-1005 F ..............13N-1006 F ..............13N-1007 ..................14N-1008 ..................14N-1009 ..................14N-1010 ..................14N-1011 ..................14N-1012 ..................14N-1013 ..................14N-1014 ..................14N-1021 ..................15N-1022 ..................15N-1023 ..................15N-1024 ..................15N-1025 ..................15N-1026 ..................15N-1027 ..................15N-1028 ..................15N-1102 ..................16N-1103 ..................16N-1104 ..................16N-1105 ..................16N-1106 ..................16N-1107 ..................16N-1108 ..................16N-1109 ..................16N-1110 ..................17N-1112 ..................17N-1113 ..................17N-1115 ..................17N-1117 ..................17N-1123 ..................17N-1124 ..................17N-1125 ..................17N-1126 ..................18

N-1127 ..................18N-1128 ..................18N-1129 ..................18N-1130 ..................18N-1131 ..................18N-1132 ..................18N-1135 ..................18N-1136 ..................18N-1137 ..................18N-1141 ..................18N-1209 ..................19N-1210 ..................19N-1211 ..................19N-1212 ..................19N-1213 ..................19N-1215 ..................19N-1218 ..................19N-1219 ..................19N-1224 ..................19N-1225 ..................19N-1226 ..................19N-1227 ..................19N-1228 ..................19N-1311 ..................20N-1312 ..................20N-1313 ..................20N-1315 ..................20N-1316 ..................20N-1317 ..................20N-1318 ..................20N-1319 ..................20N-1320 ..................20N-1321 ..................20N-1322 ..................20N-1324 ..................20N-1325 ..................20N-1326 ..................20N-1327 ..................20N-1328 ..................20N-1342 ..................21N-1343 ..................21N-1344 ..................21N-1345 ..................21N-1350 ..................21N-1360 ..................21N-1361 ..................21N-1362 ..................21N-1413 ..................22N-1415 ..................22N-1423 ..................22N-1425 ..................22N-1427 ..................22N-1443 ..................22N-1445 ..................22



N-1729 ..................32N-1731 ..................32N-1732 ..................32N-1733 ..................32N-1734 ..................32N-1735 ..................32N-1736 ..................32N-1737 ..................32N-1738 ..................32N-1739 ..................32N-1741 ..................33N-1742 ..................33N-1743 ..................33N-1750 ..................33N-1751 ..................33N-1755 ..................33N-1756 ..................33N-1760 ..................33N-1804 ..................34N-1805 ..................34N-1806 ..................34N-1807 ..................34N-1811 ..................34N-1813 ..................34N-1814 ..................35N-1814 SQ ...........35N-1815 ..................35N-1816 ..................35N-1818 ..................35N-1920 ..................36N-1930 ..................36N-1931 ..................36N-1933 ..................36N-1935 ..................36N-1938 ..................36N-1940 ..................36N-1941 ..................36N-1942 ..................36N-1943 ..................36N-1950 ..................36 N-1952 ..................44N-1953 ..................45N-1953 Mod ..........46N-2025 ..................37N-2026 ..................37N-2028 ..................37N-2030 ..................37N-2032 ..................37N-2034 ............37, 38N-2038 ..................37N-2055 ..................37N-2056 ..................37N-2058 ..................37N-2060 ..................37

N-2062 ..................37N-2064 ..................37N-2068 ..................37N-2125 ..................37N-2126 ..................37N-2128 ..................37N-2130 ..................37N-2132 ..................37N-2134 ..................37N-2138 ............37, 38N-2142 ............37, 38N-2146 ............37, 38N-2150 ............37, 38N-2154 ............37, 38N-2162 ..................37N-2170 ..................37N-2174 ..................37N-2224 ..................38N-2225 ..................38N-2226 ..................38N-2227 ..................38N-2228 ..................38N-2229 ..................38N-2230 ..................38N-2231 ..................38N-2232 ..................38N-2233 ..................38N-2234 ..................38N-2235 ..................38N-2237 ..................38N-2238 ..................38N-2239 ..................38N-2240 ..................38N-2242 ..................38N-2243 ..................38N-2244 ..................38N-2246 ..................38N-2247 ..................38N-2248 ..................38N-2249 ..................38N-2251 ..................38N-2252 ..................38N-2253 ..................38N-2255 ..................38N-2256 ..................38N-2257 ..................38N-2259 ..................38N-2260 ..................38N-2261 ..................38N-2262 ..................38N-2263 ..................38N-2264 ..................38N-2265 ..................38N-2266 ..................38

NU-STRUT nUMeRicAl pARts index



51

N-2267 ..................38N-2268 ..................38N-2269 ..................38N-2270 ..................38N-2274 ..................38N-2278 ..................38N-2280 ..................38N-2420 ..................39N-2422 ..................39N-2424 ..................39N-2426 ..................39N-2432 ..................39N-2433 ..................39N-2435 ..................39N-2439 ..................39N-2440 ..................39N-2442 ..................40N-2443 ..................40N-2449 ..................40N-2460 ..................40N-2461 ..................40N-2462 ..................40N-2463 ..................40N-2469 ..................40N-2500PL .............36N-2500PG .............36N-2500GR ............36N-2500WP ............36N-2500BP .............36N-2600 ..................41N-2601 ..................41N-2602 ..................41N-2611 ..................41N-2612 ..................41N-2650 ..................41N-2652 ..................41N-2654 ..................41N-2656 ..................41N-2658 ..................41N-2660 ..................41N-2662 ..................41N-2664 ..................41N-2666 ..................41N-2668 ..................41N-2670 ..................41N-2708 ..................42N-2709 ..................42N-2810 ..................42N-2811 ..................42N-2812 ..................42N-2813 ..................42N-2814 ..................42N-2815 ..................42N-2816 ..................42

N-2817 ..................42N-2820 ..................42N-2821 ..................42N-2822 ..................42N-2823 ..................42N-2824 ..................42N-2825 ..................42N-2826 ..................42N-2827 ..................42N-2870 ..................42N-2871 ..................42N-2872 ..................42N-2873 ..................42N-2874 ..................42N-2875 ..................42N-2876 ..................42N-2877 ..................42N-2905 ..................43N-2906 ..................43N-2910 ..................43N-2911 ..................43N-2915 ..................43N-2916 ..................43N-2920 ..................43N-2921 ..................43N-3000 ..................44N-3024 ..................44N-3025 ..................44N-3026 ..................44N-3027 ..................44N-3028 ..................44N-3029 ..................44N-3250 ..................44N-3251 ..................44N-3252 ..................44N-3253 ..................44N-3254 ..................44N-3255 ..................44N-3256 ..................44N-3257 ..................44N-3257A ................44N-3258 ..................44N-3259 ..................44N-3260 ..................44N-3261 ..................44N-3262 ..................44N-3263 ..................44N-3264 ..................44N-3265 ..................44N-3266 ..................44N-3267 ..................44N-3268 ..................44N-3269 ..................44N-3270 ..................44

N-3350 ..................45N-3351 ..................45N-3352 ..................45N-3353 ..................45N-3354 ..................45N-3355 ..................45N-3356 ..................45N-3357 ..................45N-3357A ................45N-3358 ..................45N-3359 ..................45N-3360 ..................45N-3361 ..................45N-3362 ..................45N-3363 ..................45N-3364 ..................45N-3365 ..................45N-3366 ..................45N-3367 ..................45N-3368 ..................45N-3369 ..................45N-3370 ..................45N-3400 ..................48N-3401 ..................48N-3402 ..................48N-3403 ..................48N-3404 ..................48N-3405 ..................48N-3406 ..................48N-3407 ..................48N-3408 ..................48N-3409 ..................48N-3410 ..................48N-3411 ..................48N-3412 ..................48N-3413 ..................48N-3414 ..................48N-3415 ..................48 N-3416 ..................48N-3417 ..................48N-3418 ..................48N-3420 ..................48N-3421 ..................48N-3422 ..................48N-3423 ..................48N-3424 ..................48N-3425 ..................48N-3426 ..................48N-3427 ..................48N-3428 ..................48N-3430 ..................49N-3431 ..................49N-3432 ..................49N-3433 ..................49

N-3440 ..................49N-3441 ..................49N-3442 ..................49N-3443 ..................49N-3450 ..................49N-3451 ..................49N-3452 ..................49N-3460 ..................49N-3461 ..................49N-3462 ..................49N-3463 ..................49N-3464 ..................49N-3470 ..................48N-3471 ..................48N-3472 ..................48N-3473 ..................48N-3474 ..................48N-3475 ..................48N-3476 ..................48N-3477 ..................48N-3478 ..................48N-3479 ..................48N-3490 ..................49N-3491 ..................49N-3492 ..................49N-3550 ..................46N-3551 ..................46N-3552 ..................46N-3553 ..................46N-3554 ..................46N-3555 ..................46N-3556 ..................46N-3557 ..................46N-3557A ................46N-3558 ..................46N-3559 ..................46N-3560 ..................46N-3561 ..................46N-3562 ..................46N-3563 ..................46N-3564 ..................46N-3565 ..................46N-3566 ..................46N-3567 ..................46N-3568 ..................46N-3569 ..................46N-3570 ..................46N-3724 ..................50N-3724A ................50N-3725 ..................50N-3726 ..................50N-3727 ..................50N-3728 ..................50N-3729 ..................50

N-3730 ..................50N-3826 ..................50N-3828 ..................50N-3830 ..................50N-3832 ..................50N-3834 ..................50N-3838 ..................50N-3842 ..................50N-3846 ..................50N-3850 ..................50N-3854 ..................50N-3862 ..................50N-3870 ..................50N-3950 ..................47N-3951 ..................47N-3952 ..................47N-3953 ..................47N-3954 ..................47N-3955 ..................47N-3956 ..................47N-3957 ..................47N-3957A ................47N-3958 ..................47N-3959 ..................47N-3960 ..................47N-3961 ..................47N-3962 ..................47N-3963 ..................47N-3964 ..................47N-3965 ..................47N-3966 ..................47N-3967 ..................47N-3968 ..................47N-3969 ..................47N-3970 ..................47N-1-4 ..................... 11N-1-6 ..................... 11N-1-8 ..................... 11N-1-10 ................... 11N-1-12 ................... 11N-2-0832 ............... 11N-2-1024 ............... 11N-2-1032 ............... 11N-2-4 ..................... 11N-2-5 ..................... 11N-2-6 ..................... 11N-2-8 ..................... 11N-2-10 ................... 11N-2-12 ................... 11N-2-4 NS-1 ........... 11N-2-4 NS-2 ........... 11N-2-4 NS-3 ........... 11N-2-5 NS-1 ........... 11N-2-5 NS-2 ........... 11

N-2-5 NS-3 ........... 11N-2-6 NS-1 ........... 11N-2-6 NS-2 ........... 11N-2-6 NS-3 ........... 11N-2-6 NS-4 ........... 11N-2-6 NS-5 ........... 11N-2-6 NS-6 ........... 11N-2-8 NS-2 ........... 11N-2-8 NS-3 ........... 11N-2-8 NS-4 ........... 11N-2-8 NS-5 ........... 11N-2-8 NS-6 ........... 11N-2-8 NS-7 ........... 11N-2-10 NS-2 ......... 11N-2-10 NS-3 ......... 11N-2-0832 WS ........12N-2-1024 WS ........12N-2-1032 WS ........12N-2-4 WS ..............12N-2-5 WS ..............12N-2-6 WS ..............12N-2-8 WS ..............12N-2-10 WS ............12N-2-12 WS ............12N-5-8 WS ..............12N-5-0832 ...............12N-5-1024 ...............12N-5-1032 ...............12N-5-4 .....................12N-5-5 .....................12N-5-6 .....................12N-5-8 .....................12N-6-0832 ...............13N-6-0836 ...............13N-6-1024 ...............13N-6-1032 ...............13N-6-4 .....................13N-7-0832 ...............13N-7-0836 ...............13N-7-1024 ...............13N-7-1032 ...............13N-7-4 .....................13

NU-STRUT nUMeRicAl pARts index



52

NU-STRUT notes


4775 Chino AVenue • Chino, CA 91710 • tel: (909) 591-0722 • fAx: (909) 591-6334 www.kumarindustries.net • engineering Catalog no 52

Date post:	04-Oct-2020
Category:	Documents
Upload:	others
View:	0 times
Download:	0 times

“Products With Integrity” - Kumar Industries...KUMAR INDUSTRIES, INC. Manufacturers of...

Documents