Appendix

BUDGETORY COST FOR THIS LIST.

250,000 USD

No EQUIPMENT DESCRIPTION QTY LOCATION NOTES

1 Pump Single Stage Process Pump, Overhung, with Wear Rings and Packed Gland

2 Coupling Flange type coupling with spacer to couple items 1 and 33 Electric Motor 5 HP Electric motor

4Skid/Mounting Frame for Items Above

Skid to allow Pump - Coupling - Electric Motor assembly

5Stainless Steel Pre-cut Shim Full Kits

Precut shim packs range .001" to .125" 1Workshop STORES -

Mechanical Section - Main Building - B

6 Laser Alignment Set Optalign Plus 1Workshop STORES -


8Universal Plunger Type Dial Test Indicator DTI Set (Including Clamps)

Set, Dial Test Indicator, Universal Includes jeweled bearing indicator with 1 1/2" diameter bezel and rear mounted plunger; two extra contacts (3/16" and 5/16" diameter); indicator holding rod; hole attachment for checking bores (.125 range); indicator C-clamp mounting and universal rod connector and tool post holder. Stored in Storage Case.

5Workshop STORES -


10 DTI Long Range (Plunger)

General use indicator set. Magnetic base attaches to flat surface. Checks ball joint, tie rod, cam and valve guide wear, and wheel rim, flywheel and disc brake runout. Features a large 2 1/4" diameter dial with 1" range. Dial is continuous with revolution counter. Bezel may be rotated for any setting point. Includes powerful magnetic base with post, stepped rod and clamps along with contact, rod connector and indicator holding clamp. Stored in CM6564050 Storage Case.

5Workshop STORES -


11 Small Hinged Mirror 1Workshop STORES -


12 Magnetic Base

Magnetic base with fine adjust cross-arm, suitable for clamping plunger dial indicators by their backlug or 8mm and 3/8” diameter stems. Push switch style magnetic base with vee step on top face for mounting on shafts, chucks and arbors.

3Workshop STORES -


13 Deep Groove Ball Bearings2"BRC 18 (beneficial but can NOT be used to replace proposed item)JBGP 11 (beneficial but can NOT be used to replace proposed item)

10Workshop STORES -


14Deep Groove Ball Bearings Double Row

2"BRC 18 (beneficial but can NOT be used to replace proposed item)JBGP 11 (beneficial but can NOT be used to replace proposed item)

1Workshop STORES -


2Mechanical Workshop -

Main Building - A

Petrofac Technical Training Centre - HMD, Algeria

EQUIPMENT LISTAppendix 6

MECHANICAL EQUIPMENT

15 Angular Contact Ball Bearings2"BRC 18 (beneficial but can NOT be used to replace proposed item)JBGP 11 (beneficial but can NOT be used to replace proposed item)

1Workshop STORES -


16Four Point Contact Ball Bearings Separable

2"BRC 18 (beneficial but can NOT be used to replace proposed item)JBGP 11 (beneficial but can NOT be used to replace proposed item)

1Workshop STORES -


17 Self Aligning Ball Bearings2"BRC 18 (beneficial but can NOT be used to replace proposed item)JBGP 11 (beneficial but can NOT be used to replace proposed item)

1Workshop STORES -


18 Cylinderacal Roller Bearings2"BRC 18 (beneficial but can NOT be used to replace proposed item)JBGP 11 (beneficial but can NOT be used to replace proposed item)

1Workshop STORES -


19 Taper Roller Bearings2"BRC 18 (beneficial but can NOT be used to replace proposed item)JBGP 11 (beneficial but can NOT be used to replace proposed item)

1Workshop STORES -


20 Barrel Roller Bearings2"BRC 18 (beneficial but can NOT be used to replace proposed item)JBGP 11 (beneficial but can NOT be used to replace proposed item)

1Workshop STORES -


21 Spherical Roller Bearings2"BRC 18 (beneficial but can NOT be used to replace proposed item)JBGP 11 (beneficial but can NOT be used to replace proposed item)

1Workshop STORES -


22 Axial Deep Groove Ball Bearings2"BRC 18 (beneficial but can NOT be used to replace proposed item)JBGP 11 (beneficial but can NOT be used to replace proposed item)

1Workshop STORES -


23 Axial Spherical Roller Bearings2"BRC 18 (beneficial but can NOT be used to replace proposed item)JBGP 11 (beneficial but can NOT be used to replace proposed item)

1Workshop STORES -


24Axial Angular Contact Ball Bearings

2" 1Workshop STORES -


25Selection of Small Shafts with Bearings

Bearings required - 2 off of each - standard duty - low cost units - suggest SKF as supplier (www.skf.com). LIST - Deep groove ball bearing (open basic design) dia 50 mm bore, Angular contact ball bearing (single row contact) dia 50mm, Cylindrical roller bearings (single row caged) Dia 50 mm, Tapered roller bearings (single row) Dia 50 mm. Shafts to suit bearings (shafts should be to an h9 tolerance but the cylindricity should be to IT5/2 according to ISO 1101:2004). SKF should be able to supply bearings to suit small shafts. The bearings and shafts are for mounting and dismounting training purposes and will never be run within a machine.

3Workshop STORES -


26 Bearing Locknuts 2" 2Workshop STORES -


27 Plummer Block 2" 1Workshop STORES -


28 Flanged Bearing Housing 2" 1Workshop STORES -


30 Bearing Heater - Induction 1Workshop STORES -


32Pump Multistage Horizontally Split


Main Building - ASuggest used equipment because high cost item and used equipment provided indications of wear/failures.

33 Pump Multistage Barrel 1Mechanical Workshop -


34 Pump Multistage 1Mechanical Workshop -


35 Pump Single Stage 1Mechanical Workshop -


36 4" Gate Valves (Rising Steam) 3Mechanical Workshop -

Main Building - ASuggest used equipment.

374" Gate Valves (Non Rising Steam)



38 2" Plug Valve 1Mechanical Workshop -


39 3" Gobe Valve 1Mechanical Workshop -


40 1" Check Valve - Ball 1Mechanical Workshop -


41 1" Check Valve - Swinging Gate 1Mechanical Workshop -


42 1" Needle Valve 1Mechanical Workshop -


43 2" Ball Valve 1Mechanical Workshop -


44 4" Butterfly Valve 1Mechanical Workshop -


45 1 1/2" Pressure Relief Valve 1Mechanical Workshop -


46 1 1/2" Safety Valve 1Mechanical Workshop -


47CUT AWAY VALVE - Gate Valve 125# - 2” Flanged

1Mechanical Classroom - B

Building

Suggest using used equipment and cutting away 1/2 or 1/4 to allow learner visualisation of internal construction and operation.

48CUT AWAY VALVE - Globe Valve 125# - 2” Flanged


Building


52CUT AWAY VALVE - Ball Valve 2” Flanged


Building


54CUT AWAY VALVE - Safety Valve 2” Flanged


Building


MECH 56 Lapping Plate

Hand Lapping Plate - 18" Diameter. Cast iron Hand Lapping Plate, suitable for maintenance workshops and can be used for lapping parts to extreme flatness.Serrated with a square cross-hatched pattern or solid (unserrated) and in 18" diameters.


Main Building - A

57Compressors Positive Displacement (Small Piston Unit)

Small piston unit to strip down 1Mechanical Workshop -


59Well Head Control Panel and Xmas Tree Valve (Second Hand)



Mech 62 Pneumatic Training Station Floor standing panel with three actuators, control valves, etc. Basic unit 1Mechanical Workshop -

Main Building - A

Mech 63 Hydraulics Training StationFloor standing panel with three actuators, control valves, power unit (pump, tank, acumulator, relief valve etc.) Basic unit


Main Building - A

MECH 64 Chemical Wash Station

Small part cleaning station either Aqueous Manual Parts Washers or ultrasonic parts cleanerfeatures include:· Full Stainless Steel or robust Polypropylene Construction· Hand held Brush· Hinged machine lid· Removable Work Tray· Solution Rinse Off· Low fluid Level Protection· Electric Fluid Heaters· Fluid temp control - max 42ºC· Inline Fluid FiltrationExample - http://www.technowash.com/products_aqueous.htm


Main Building - A

66 Hydraulic Press 10 tonne - bearing and universal press with jaws 1Mechanical Workshop -

Main Building - A

MECH 67 Manual Mobile Crane

Capacity 1000kgFlow control valve gives precise lowering and positioning Plated pins prevent rust damage Manual hydraulic operation Heavy duty full swivel hook fitted with a safety clip Nylon wheels with braked swivel castors prevent crane moving during use Jacks from folded position Overload valve prevents damage to crane Deadman lowering control for safety

EXAMPLE: JCB Sitemaster mobile crane - Model CR-1000-YW-JCB


Main Building - A

68Couplings Selection (to include: Universal, Fixed and Flexible Couplings)

Second hand system or fabricated system

See attaced sheet on coulpings. We need 1 off of each of the following couplings - Chain type, Gear type, Oldham type, Spider type, Disc type, Pin type, Spring type and Tyre type. All 50mm bore (approx). Used as demonstration units during lessons. Suggest getting a price from " the machinery people".,



Mech 69Belt Drives (Selection to Include: Vee, Poly Vee, Toothed, Linked)

Second hand system or fabricated systemWe need minimum 1 off of each of the following belts and matching pulleys - Flat, Vee, Poly vee, Timing/Synchronous and linked vee type. All short lengths of samples. Used for demonstration during lessons. Suggest getting a price from " the machinery people". Main supplier/manufacturer Renolds.



70

Chain Drives (Selection to Include Systems: Link, Slat, Roller, Inverted Tooth and Flat Chain Drives)

We need minimum 1 off of each of the following chains and matching sprokets - Roller, inverted tooth and leaf type. All short lengths (200mm approx). Used for demonstration during lessons. Suggest getting a price from " the machinery people". Manufacturers Fenner, Emerson etc...,.



71Gear Drives (To Include: Spur, Bevel, Epicyclic, Helical, Spiral, Worm, Ratchet)

Second hand system or fabricated system

A combined unit from DAC rebranded via Edutech can be obtained at - http://www.dac-3d.com/DACTRNG/PRODMECH/205INFO.HTM



72Gearboxes (Selection to Include Gears in Description)

To include spur, bevel, epicyclic, helical, spiral, worm, ratchet 1Mechanical Workshop -


MECH 73Clutches and Brake Systems (Selection)

To include a selection of Drum, disc, centrifugal, conical, magnetic. 1Mechanical Workshop -


74Selection of Shafts - Plain, Spline, Hollow, Crank and Cam Shafts



75Selection of Keys - Woodruff, Stepped, Feather, Qib, Fixed Slidinq Keys

with approximate length of 50 mm, it will be used for only or training display purposes only.

Example: Woodruff, gib head and parrallel keys - selection as samples - http://www.tasmanindustries.co.uk/index.php?option=com_content&task=view&id=14&Itemid=15 Key selection - http://www.ondrives.com/products.asp?subcatid=83

1Workshop STORES -


76Selection of Pins - Shear, Taper and Split Pins

with approximate length of 50 mm, it will be only used for training display purposes only.

Example: split pins - sample for demo - http://tasmanindustries.co.uk/index.php?option=com_content&task=view&id=27&Itemid=26&gclid=COjFmvG9rZwCFU0B4wodL1dZjg Slotted spring pin - http://www.ondrives.com/products.asp?subcatid=85 http://www.ondrives.com/products.asp?recnumber=675

1Workshop STORES -


78 Selection of Pegs and Dowels

Approximate size of 6-8mm, 50 mm long will be fine, it will be only used for training display purposes only.

Example: http://www.ondrives.com/mechanical-dowel-spring-pins.html

1Workshop STORES -


79Selection of Bushes Including Taper Lock

1Workshop STORES -


MECH 80 Horizontal BandsawMotor: 400V 50Hz 1.2kWCutting Speed: variable (41-63.4 m/min)Sawblade size: 3280x27x0.9


Main Building - A

MECH 81 Heavy angle Duty Grinder

Grinding Disc Dia.: 180 - 230 mm Power Input : 2000 W No-load Speed : 8500 rpmSpindle Thread : M 14


Main Building - A

82 Bench Grinder Bench grinder,200mm 2/3HP 220-240Vac 1Mechanical Workshop -

Main Building - A

84Pedestal Drilling Machine 3 Phase

Drill capacity 32mm, Spindal to column and table - 420 and 777mm, Spindal taper 4MT, Table 600mm X 4600mm, 1.5HP Motor + coolant, 3PH 440v supply, Speed range 75 to 2100 rpm with power feed.


Main Building - A

85 9" Grinders

Angle Grinder 125mmRear Handle 5" grinderGear housing swivels at every 90 degreesFeaturing AC/DC lock-on switchWheel GuardWheel size: 125mm Bore Size: 22mm Spindle size: M14x2mm No Load Speed: 11,500rpm Input wattage: 1050w


Main Building - A

MECH 86 Chop Saw 14'' chop saw, Bench mount - Blade speed 2800rpm, 1Mechanical Workshop -

Main Building - A

88 Pallet Truck Pallet Truck, 235mm between forks, heavy duty truck suitable for warehouse & general handling duties,

1Workshop STORES -


MECH 89 A Frames 2.5T 1Mechanical Workshop -

Main Building - A

90 Selection of Power Tools (110v) Tools (Drills + Screwdrivers 1 off) 4Workshop STORES -


91Air Operated Power Tools (Impact Wrench 1/2" Drive, Drill upto 1/2" Chuck)

1Workshop STORES -


92 Assorted Lifting Equipment

WLL 1t x 1m EWL Fibre SlingsSWR slings 10mm dia x Galv RHOL Soft eyes both ends x .5m x WLL 1t maxBow shackles c/w safety type anchor pin WLL 4.75tBow shackles c/w safety type anchor pin WLL 3.25tEye Bolt to BS4278 – 8mm threadEye Bolt to BS4278 – 10mm threadEye Bolt to BS4278 – 12mm threadEye Bolt to BS4278 – 14mm threadEye Bolt to BS4278 – 16mm threadEye Bolt to BS4278 – 18mm threadEye Bolt to BS4278 – Imperial 3/8 threadEye Bolt to BS4278 – Imperial 1/2 threadEye Bolt to BS4278 – Imperial 5/8 threadEye Bolt to BS4278 – Imperial 3/4 threadEye Bolt to BS4278 – Imperial 7/8 threadEye Bolt to BS4278 – Imperial 1 thread

1Workshop STORES -


94 Digital Tachometer

Combination contact/non-contact tachometer with Minimum (MIN), Maximum (MAX) and LAST or current reading. Non-contact operation uses photoelectric sensor and reflective tape (included). Contact measurements are taken with one of three contact adaptors: cone, concave wheel or large wheel. Current data will remain until the next reading is taken. Memory figures will remain until the next recorded reading is taken. Powered by 2 AA batteries (included) and a protective case.Ranges:Photo Tach: 5 – 30,000 RPMContact Tach: 0.5 – 19,999 RPMSurface Speed: 0.2 – 6,560 ft/min. or 0.5 – 1,999 m/min.

1Workshop STORES -


MECH 95 Surface Plates/Inspection PlatesCast Iron Surface Plates 800 Series - 300 X 300mm Grade 2 MOORE AND WRIGHT - MW800-01 300 x 300mm

2Workshop STORES -


MECH 96 Surface Gauge

Universal type:Designed for precise marking out operations Hardened and tempered steel base, ground on one end and bottom face Vee groove for locating on cylindrical workpieces Two retractable locating pins Radial grooves in the side facilitate comfortable handling One handed fine adjustment Supplied with two interchangeable pillars and one 4mm diameter scriber

2

MECH 97 Vee-Blocks VEE BLOCKS with Clamps 2Workshop STORES -


MECH 98 Vee-Blocks 100 X 100 mm & 160mm & 200mm 1 pair of each 3Workshop STORES -


MECH 99 Vernier Height Gauges 0 - 500MM 1Workshop STORES -


Mech 101 Parallels Pair: 1/4" (6mm) Thick, 3/8" (10mm) Width 1Workshop STORES -


Mech 102 Parrallels Pair: 3/8" (10mm) Thick, 1/2" (13mm) Width 1Workshop STORES -


103 Marking Off Table1m X 1m Surface finish to DIN 876/III – Planed/Milled Flatness to the same standard. Thus 120 microns over the 2000mm table

1Workshop STORES -


MECH 104

Angle Plates 160mm/6.30" 2Workshop STORES -


MECH 107

Selection of Seals

O ring, Lip, chevron, U type, gaskets, etc.

Suggest you contact James Walker and ask for set of samples as demo's for training - http://www.jameswalker.biz/group/categories/walkersele_radial_lip_seals.html. Seal samples to include - O ring, Lip, chevron, U type, gaskets....,.

1Workshop STORES -


108 Hydraulic Tester

Hand Operated Hydraulic Pressure Test Pump· Hand operated hydraulic test pump for proving valves, water pipes, boiles, vessels etc. · Lightweight, easy to use and of robust construction.· Tank capacity: 5 litres approx. · Test capacity: 50 bar (700psi) approx max. · Hose connections: 1/2 BSP nominal. · Must hold pressure when required for extended periods.Example - http://www.toolbaydirect.co.uk/catalogue/product/Pressure-Testers/427/Monument-1382M-5-Litre-Hand-Operated-Hydraulic-Pressure-Test-Pump/165143/

1Workshop STORES -


MECH 114

Mechanical Seals Selection for training purposes including sectioned 1Workshop STORES -


MECH 120

Socket Set 1/2 Inch Drive - Metric

Set, General Service use, 12-Point (35 pcs.) 3Mechanical Workshop -

Main Building - A - TOOL CHEST

MECH 121

Socket Set 1/2 Inch Drive - Imperial

Set, General Service use, 12-Point (35 pcs.) 3Mechanical Workshop -


MECH 122

Extension for Sockets Extension, Locking,1/2'' drive, Extra Long, 12", 1Mechanical Workshop -


MECH 123

Universal Joint for 1/2 Socket Set Universal Joint 1Mechanical Workshop -


MECH 124

T-Handle Extensions 1Mechanical Workshop -


MECH 125

1/4 inch Socket Set - Metric and Imperial

Set, General Service, 12-Point (35 pcs.) 1Mechanical Workshop -


MECH 126

3/4 inch Socket Set - Metric and Imperial

Set, General Service, 12-Point (35 pcs.) 2Mechanical Workshop -


MECH 127

Torque Wrench TORQOMETER, Imperial/Metric, Basic, 100 ft. lb./14 kg•m, 1/2" drive 1Workshop STORES -


Mech 128 Torque WrenchTORQOMETER, Imperial/Metric, Basic, range up to 350 N.m, 3/4" driveExample: RS 264-2173, Proto micrometer torque wrench,70-350Nm

1Workshop STORES -


Mech 129Spanner Sets up to 1" and 25mm - 48 Piece - Open-ended and Ring (Including Offset)

48 Piece Set. Comprehensive set of Open End and Ring Spanners in a heavy duty roll. Includes the most popular sizes. Chrome Vanadium Steel with polished heads. 20 x combination 6-25mm, 12 x combination ¼” - 1” AF, 8 x double open end 6 x 7 - 20 x 22mm, 8 x ring end 6 x 7 - 20 x 22mm.



MECH 130

Open-Ended and Ring Spanner Set Up To 2"/50mm

Up to 2"/50mm 1Mechanical Workshop -


MECH 131

Nut Splitter For splitting nuts up to 3/4" across the flats. Bar acts as a handle to hold tool securely.



MECH 133

Allen Key Sets - L Type With Ball End - Metric

9 Piece Set. Very tough screwdriver bit material will not round-out in hex screws or bolts. Metric sizes. Round, Coated Bars Ball End 1.5, 2, 2.5, 3, 4, 5, 6, 8, 10mm keys and clip.



MECH 134

Allen Key Sets - L Type With Ball End - Imperial

9 Piece Set. Very tough screwdriver bit material will not round-out in hex screws or bolts. Ball End 1/16 to 3/8 " keys and clip.



MECH 135

Allen Key Sets - T Type With Ball End - Metric




MECH 136

Allen Key Sets - T Type With Ball End - Imperial

9 Piece Set. Very tough screwdriver bit material will not round-out in hex screws or bolts. Ball End 1/16 to 3/8" keys and clip.



MECH 137

Hacksaw

Designed for 12" (300mm) blades. Allows very high blade tension for accurate and exact kerfs. Spring tensioned blade loading mechanism, strong rectangular back section for blade storage with an easy to handle retaining screw. Positions for normal flush cutting or 55° for angle or horizontal cutting. Can be used as a compass saw.

12

Workshop STORES - Mechanical Section - Main Building - B or Workshop

benches

MECH 138

Junior HacksawsSquare bar steel frame, with comfortable moulded plastic handle, enclosed for finger protecion, incorporating a quick, easy lever action blade locking and change feature

3Workshop STORES -


MECH 139

Drill Bit Set HSS - up to 3/8"Drill bit set 21 piece HSS - up to 3/8 (21 pcs) (1/16" to 3/8") in metal drill bit index.


Main Building - A - TOOL CUPBOARD IN WORKSHOP

MECH 140

Drill Bit Set HSS - up to 10mm Drill bit set 21 piece HSS - 3mm to 10mm in metal drill bit index. 2Mechanical Workshop -


MECH 141

Drill Bit - Set Drill bit set - 3/8" to 1", HSS (High Speed Steel) 2Mechanical Workshop -


MECH 142

Drill Bit - Set Drill bit set - 10mm to 25mm, HSS (High Speed Steel) 2Mechanical Workshop -


MECH 143

Extractor Set Extracts broken screws from 1/4" to 1/2" diameter. Comes in a storage case. 1Workshop STORES -


MECH 144

Engineers File - 300mm Second Cut - Hand (With Safe Edge)

High grade alloy steels to British standard BS498 and ISO standards. Edges parallel, surfaces double cut. Note - Except for the hand, dual cut, pillar and knife which have one safe (uncut) edgeUse: High removal rates. Ideal for working high-alloy tool steels

12


benches

MECH 145

Engineers File - 300mm Second Cut - Flat


10


benches

MECH 146

Engineers File - 300mm Second Cut - Half-Round


12


benches

MECH 147

Engineers File - 300mm Second Cut - Round


12


benches

MECH 148

Engineers File - 300mm Second Cut - Square


20


benches

MECH 149

Engineers File - 300mm Second Cut - Three Square


12


benches

MECH 150

Engineers File - 300mm Smooth Cut - Hand (With Safe Edge)

High grade alloy steels to British standard BS498 and ISO standards. Edges parallel, surfaces double cut. Note - Except for the hand, dual cut, pillar and knife which have one safe (uncut) edgeUse: Ideal for working high-alloy tool steels

12


benches

MECH 151

Engineers File - 300mm Smooth Cut - Flat


12


benches

MECH 152

Engineers File - 300mm Smooth Cut - Half-round


12


benches

MECH 153

Engineers File - 300mm Smooth Cut - Round


12


benches

MECH 154

Engineers File - 300mm Smooth Cut - Square


12


benches

MECH 155

Engineers File - 300mm Smooth Cut - Three Square


12


benches

MECH 156

Engineers File - 300mm Smooth Cut - Pillar


1Workshop STORES -


MECH 157

Engineers File - 300mm Smooth Cut - Knife


1Workshop STORES -


MECH 158

Engineers File - 300mm Bastard Cut - Hand (with Safe Edge)

High grade alloy steels to British standard BS498 and ISO standards. 1Workshop STORES -


MECH 159

Maintenance File Set - 4" Second Cut

Precision files manufactured in accordance with SQS quality management system to ISO9001/EN29001Files are manufactured from high-grade chrome steel, hardened to 65 HRC for greater cutting capactiy and prolonged tool lifeIdeal for use in limited access areas, these files are designed for engineers who require a file larger than needle, but smaller than engineersOverall length 4 inches in Cut 2, fitted with wooden handles for safe useSet comprises one each, flat, warding, square, three-square, round, and half-roundSupplied in a PVC wallet

2Workshop STORES -


MECH 160

Hammer Set (Ball Pein) Set, Hammer, Hickory Handle - 8, 12, 16 and 24 Oz - 4 pcs. 2Mechanical Workshop -


MECH 161

Dead Blow Hammers

Hammer, Dead Blow, Dual Face Drilling, 32 oz. Dead Blow Hammer with low rebound. Ribbed, textured grip with energy absorbing material to enhance comfort and reduce vibration.• Composite handle shank improves the hammer balance while defusing shock.• Free-flowing steel head canister design improves dead blow action and reduces rebound.• Non-sparking, chemical resistant molded urethane covering.• Ribbed thumb rest allows user to choke up in tighter work areas.• Bright color for high visibility.



MECH 162

Bronze Face Hammer

Hammer, Bronze Tip, 16 oz. Bronze faces are soft enough to "give" when contact is made with metal parts. Ribbed, textured grip with energy absorbing microcellular material enhances comfort and reduces vibration. Non-sparking, chemical resistant urethane covering. Multi-position hand grip allows user to "choke up" in tighter work areas. Wide flare at end of handle helps prevent hammer from slipping.



MECH 163

Soft Faced Mallet/Hammer (Nylon Face)

1 Kg with replaceable faces 2Mechanical Workshop -


MECH 164

Bronze Drift Punch 2Mechanical Workshop -


165 Pin Punch Sets - Bronze and Steel 2Mechanical Workshop -


MECH 166

Combination Chisel Set Set, Chisel, 10 pcs. (Flat/Half Round Nose Cape/Cape/Diamond Point) 1Mechanical Workshop -


MECH 167

Centre Punches 90 deg tip 6Mechanical Workshop -


168 Dot Punches 60 deg tip 6Mechanical Workshop -


MECH 169

Scraper Set Set, Striking Scrapers, 3 pcs 2Mechanical Workshop -


MECH 170

Pliers Adjustable Joint Pliers adjustable joint - Pliers, Adjustable Joint, Interlocking Channel, Industrial Finish, 9 1/4"



MECH 171

Cutters 4 1/4" Cutters, Diagonal Grip 2Mechanical Workshop -


MECH 172

Standard Pliers - Lineman 7 3/8" (7 3/8"). Machined cutter heads for perfectly matched blades. Heads are induction hardened. Additional gripper teeth behind the heads. Industrial finish and red vinyl covered handles.



MECH 173

Locking Pliers (4 in Set) Set, Locking Pliers, Standard Grip, 3 or 4 pcs. 2Mechanical Workshop -


MECH 174

Long Nose Pliers 2Mechanical Workshop -


MECH 175

Needle Nose Pliers 2Mechanical Workshop -


MECH 176

Retaining Ring Plier Sets (Circlip Pliers)

Set, Pliers, Retaining Ring, 2 pliers 2Mechanical Workshop -


MECH 179

Pinch BarsUsed to align, adjust and move metal and wood. Angled chisel end for extra leverage when prying.



Mech 180 Utility BarSmall size provides access in tight quarters. Pull nails, tacks or staples. Pry open lids and drawers. Scrape paint, glue and gaskets. Chrome plated for corrosion protection. Overall dimensions of 5 3/8" x 1 1/4" x 5/8".



MECH 181

Puller, Separator and Extractor Set

Comprehensive puller, separator and extraction set. 1Mechanical Workshop -


MECH 182

Screwdriver Sets - Flat Tip Impact Screwdrivers - SETS - 5 per set

Heavy, square cross-section blades, matt chrome plated with gun finished tipsShatterproof handles with heavy steel striking plate for impacting. 5 per set 3 to 11mm tip size



MECH 183

Screwdriver Sets - Philips - SETS - 5 per set

Pro Screwdrivers. Tip sizes No 0, 1, 2 and 3. Hardened tips. 3Mechanical Workshop -


MECH 184

Screwdriver Sets - Torx Pro Screwdrivers. Tip sizes TX6, TX8, TX10, TX15, and TX20. Hardened tips 1Mechanical Workshop -


Mech 185 Screwdriver Sets - Posidrive High quility Screwdrivers with range of tip sizes. Hardened tips. 1Mechanical Workshop -


MECH 186

Thread Files - Imperial and Metric

The files included can service a range of 9 through 32 threads per inch and 0.75 through 3mm pitches.

1Workshop STORES -


Mech 187 Combination Tap and Die Sets Set, Tap and Die, U.S./Metric Combination, 117 pcs. (1/4" to 1/2" NF/NC, 3mm to 12mm).

2Workshop STORES -


MECH 188

Combination Set (Marking Out)

Three measuring heads are attached to the stainless steel ruler, allowing versatile measurements on various types of work piecesSquare head, protactor head and centre head For various measuring and marking applications Hardened and ground slide ways Stainless steel rule with engraved graduations

2Workshop STORES -


MECH 189

External Micrometer - 0-1" - Standard: BS870, DIN 863/1, ISO361

Traditional Outside Micrometer - 1961 and 1965 Series 5Workshop STORES -


MECH 190

External Micrometer - 0-25mm - Standard: BS870, DIN 863/1, ISO361

Traditional Outside Micrometer - 1961 and 1965 Series 5Workshop STORES -


MECH 191

External Micrometer Set - 0 to 200mm - Standard: DIN 863

Micrometer set 0-200mm Resolution 0.01mmSatin-chrome scale Satin chrome forged steel frame with insulated grip With tungsten carbide measuring faces and constant force ratchet Packed in wooden box with standards and adjusting key

1Workshop STORES -


MECH 192

External Micrometer Set - 1" to 5" - Standard: DIN 863 - 4 off Set

Imperial Micrometers 1" to 5" - 2 1 - 2" , 2 - 3", 3 - 4" and 4 - 5" 1Workshop STORES -


MECH 193

Steel Rules 150MM 12


benches

MECH 194

Steel Rules 300MM 12


benches

MECH 195

Calipers - Set 150mm - inside, outside and dividers 2Workshop STORES -


MECH 196

Feeler GaugesUsed for inspection of Ex d equipment, All sets have blades manufactured from hardened and tempered steel, and have mild steel cases & calibrated

2Workshop STORES -


MECH 197

Depth Micrometers

Depth gauge micrometers manufactured to the tolerances required by BS6468Constant force ratchet-stop and positive locking clampAdjustable to compensate for wear, size 0 to 6 inch

2Workshop STORES -


MECH 198

Inside Micrometer SetInternal micrometer with ground convex anvilsRange 5 to 30mm

1Workshop STORES -


MECH 199

Gauge Test for Micrometers1 of each - Metric and Imperialstandards lengthe to checking micrometers 50mm, 75mm, 100mm

3Workshop STORES -


MECH 200

Small Hole Gauge Set - Dimension Transfer (Often Called TESSA's)

Knurled knob at handle for size adjustment. Full round gauging surface with flat bottom. Set includes: .125 to .200" ga., 3 5/8" long; .200 to 300" ga., 3 7/8" long; .300 to 400" ga., 4" long; and .400 to 500" ga., 4 1/2" long.

1Workshop STORES -


MECH 201

Engineers Level230 mm, 3 vials: horizontal, vertical and 45°Grooved top surface1mm/m accuracy

1Workshop STORES -


MECH 202

Metric Tape 2 types will be needed 3 meter (12 units) & 10 meter (1 unit) 12Workshop STORES -


MECH 203

Caliper Vernier 150mm 12Workshop STORES -


MECH 204

Caliper Vernier 300mm 1Workshop STORES -


MECH 205

Engineers Squares 100mm 6Workshop STORES -


MECH 206

Thread Gauges - ImperialMeasures Imperial or sharp "V" threads. Includes 18 plated blades for the following thread sizes: 8, 9, 10, 11, 11 1/2, 12, 13, 14, 16, 18, 20, 24, 27, 28, 32, 36, 40, and 44 threads per inch.

2Workshop STORES -


MECH 207

Thread Gauges - Metric As above except - Measures Metric thread pitches - 0.75 to 3mm 2Workshop STORES -


MECH 208

Drill Gauge 0.5 - 13.0mm 2Workshop STORES -


Prod 3 Pump & Isolations Flow Rig

Two pumps set up as bypass - Used for LOTO and safe isolationTwo single stage close coupled centrifugal pumps with Electric motors (0.75 KW approx). Pipeworrk with isolation valves configured so that each pump can be operated as duty and standy-by. Electrical conections so that each pump can be locked and tagged when isolated. Suitable points for spectical blinds to be installed when isolation is required. Note the pumps will not operate and the electrical connections will only be made between the pumps and the breakers/motor control panel. There will not be an electrical connection to a power supply. Suggest a drawing extract is tacken from PEC or Sudheer and then a fabrication company is requested to supply a skid price.

1Workshop STORES -


Cabinet Drawer

Cabinet Drawer

0.85 to 1.0m height2 in the mechanical workshop1 in the eclectrical workshop1 in the instrumentation workshop


Main Building - A

PROD 22 Acrylic Heat Exchanger U-Tube

HECT-2 U-Tube Circulation Trainer Specification & Sizes: U-Tube Acrylic Heat Exchanger 8” Tubes 1/2” Length 32” This table top working model has two (2) circulation pumps and two (2) supply tanks for demonstration. Different colored water streams will be circulated through the shell side and through the tube side to simulate the working of a real heat exchanger.


Building

PROD 26 Distillation Training Tower

DTU-4 Acrylic Distillation TowerDimensions: (Packed Column) Height: 90" Diameter: 8" At 7 and ½ Feet tall this working model is an impressive and dynamic educational piece of equipment.It dramatically demonstrates the operation of a column using water and air. The models simulation is designed to show the basic process of distillation. Liquid traveling downward comes in contact with the vapors (gas bubbles) traveling upward, thus allowing the cooler liquid to condense any heavy compounds out of the lighter vapor stream.


Building

PROD 28 Distillation Training Trays

#290-010 column packing modelTray 2 Distillation Training TraysDimensions: Height: 36" Diameter: 17" Downcomers: 9" Acrylic static model with examples of bubblecaps, valve and sieve trays.


Building

PROD 29Transparent Heat Exchanger Model

6020 Multi-Pass Floating Head 1Mechanical Classroom - B

Building

PROD 30Transparent Heat Exchanger Model

6021 Fixed Tube Sheet Multi-Pass 1Mechanical Classroom - B

Building

PROD 37 Cut-away Centrifugal Pump9001 Centrifugal Single Stage Pump with Open Impeller & mechanical seal


Building

PROD 40 Tank Models

DAC via Edutec may manufacture these modelshttp://www.dac-3d.com/DACMODL/MODLHOME.HTM

Fixed roof, floating roof, etc...,.

Small models for display use to demonstrate the types of storage tanks available - to include,Fixed roof, cone roof, dome roof, umbrella roof, floating roof (inc internal). Models appoximately 150mm in height and diameter. LNG storage display models would also be advantagous. I can not see a supplier suggest approaching Edutec.


Building

PROD 41 Fired heater models 1Mechanical Classroom - B

Building

PROD 42Distillation tower packings models

Ring samples - 1" IMTP, Pal ring, Rashing ring, mela pack 1Mechanical Classroom - B

Building

Prod 47 Multi-hasps 2Workshop STORES -


Prod 48 Padlocks 10Workshop STORES -


Prod 49 Chains 4Workshop STORES -


Prod 50 Car Seal - 10" 1Workshop STORES -


PROD 10Personal Oxygen Monitor & Explosive Gas Monitor

6Workshop STORES -


9Stores Crib Units Heavy Duty Tool Chest


Main Building - A


550,000 USD


E&I 1 Basic Instrument Training Panel

Built to allow hands on training, the BIT consists of two tanks, a level column, magnetic drive pump and three control loops. The control loops are for level, flow and pressure control. Operating ranges are of level. The standard unit comes with one pneumatic loop, and two conventional electronic loops. The pneumatic loop can control either the flow or the level. The pressure control loop is a split range set-up. The two tanks are for two liquids of different specific gravities.

1Instrument Workshop -

Main Building - A

E&I 2 PID Process Control Trainer

The PID Process Control Trainer provides basic process control training using a simulated level control application and an embedded generic process controller. Using front panel-mounted controls, the controller can be tuned to provide proportional, proportional plus integral (reset), proportional plus derivative (rate), and proportional plus integral plus derivative control actions. Both open and closed loop tuning techniques can be used.


Main Building - A

E&I 3 Process Trainer

The Process Trainer, Advanced, is a self-contained, realistic, working fluid process designed for hands-on training. The training device is used to teach process measurement and control fundamentals involving flow, pressure, level and temperature applications.


Main Building - A

E&I 4Programmable Logic Controller (PLC) System Training Panels

Training Panels. Using different PLC's (Allen Bradley, Siemans, Honeywell, Omron), sensors, lights, small electric motors etc.

The options are as follows either a bought in bench top unit or a purpose built system on a free standing frame constructed by Sudheers people in Singapore (sudheers to allow for an arry of I/O - to include limit switches, motors vis relays, lights, etc.,...) Which ever option is used each of the two units in Option A must have different PLC's. For the bought in units suggest DAC via Edutech - http://www.dac-3d.com/DACTRNG/PRODELEC/462INFO.HTM or Festo. Required 8 Inputs and 8 Outputs approx


Main Building - A

6 HammerAnti-vibe Curved Claw Hammer, Overall Length 338mm, Head Material: Forged Carbon Steel

3Workshop STORES - E/I

Section - Main Building - B

7 Soft Face Hammer Material: Polyethylene 3Workshop STORES - E/I


E&I 8 Wrench 4 Pc. Flex Head Ratcheting Wrench Completer Set 2Workshop STORES - E/I


ELECTRICAL & INSTRUMENTATION EQUIPMENT



9 Spanner Set 8 Piece Fork-Ring Spanner Set 2Workshop STORES - E/I


10 Screwdriver Set 7-Pc. Cushion Grip Assortment Screwdriver Set 2Workshop STORES - E/I


11 Adjustable Spanner Ratchet Action Hook Wrench, 8-14mm Jaws 6Workshop STORES - E/I


12 Toolkit

30 Piece Engineers Zipped Toolkit, Standard De-Soldering Tool, Solder Dispenser, Standard Cutters, Snipe Nose Radio Pliers, Standard Wire Strippers, Combination Pliers, Heavy-Duty Side Cutters, Flared Tip Screwdriver, Parellel Tip Screwdriver, Straight Point Tweezer, Supadriv/Pozidriv Screwdrivers, Screw Gripping Drivers, Small Mains Test Neon Screwdriver, Pocket Screwdriver, Nut Spinners, Spanner Set, Adjustable Spanner



E&I 13 Toolbox 15in Barn Steel Toolbox, 662 x 222 x 194mm 3Workshop STORES - E/I


14 Engraving Hand Machine 1Workshop STORES - E/I


15Soldering Iron, Solder, De-soldering

80W soldering iron, with standExample: RS 3109908



16 Drill Manufacturers Part No. DV20VB2 230 V, Voltage:230V, Power: 750W 2Workshop STORES - E/I


E&I 17 File KitContact file kit, Diamond faces; 1 coarse 0.019", 1 medium 0.017", 1 fine 0.011"



18 Reamers RS Stock No. 600-672 2Workshop STORES - E/I


19 Tube BenderHeavy duty pipe bender suitable for bending 3/16", (4·75mm), 1/4" (6mm), 5/16" (8mm) & 3/8" (10mm) O/D copper & steel tubing



20 Tube Cutter Part No 635-B-EX, for tube size 1/4" to 1 1/2" OD 4Workshop STORES - E/I


21 Tube Deburring Tool Model : 226-SS or MS-TDT-24 4Workshop STORES - E/I


E&I 22 Tru-Kut Vice Model : 710439, Tube size: 3/16" OD to 2" OD 4Workshop STORES - E/I


23 Ferrule Presetting Toolkit RS Components UK site part number - 266-0288 4Workshop STORES - E/I


E&I 24 Rotary Wrench

"Model : Parker PAK-32

Example: http://www.parker.com/portal/site/PARKER/menuitem.5f7d57d9c19d0b688621d68a237ad1ca/?vgnextoid=e3418657ef7e2110VgnVCM100000c9040d0aRCRD&divId=687516&divName=Part+Detail&catId=1892&catName=P-32 ROTARY WRENCH&partNumber=P32-PAK&srcTypeId=PART_DETAIL_PAGE&country=United States&noun=&modifier=&vgnextfmt=EN"



25 Hacksaw 2 position hacksaw frame, 300mm blade 4Workshop STORES - E/I


E&I 26 Crimping Tool Wire striper & crimper tool, 0.5-2.5sq.mm 4Workshop STORES - E/I


27 Needle Nose Plier High quality, hardened jaws, soft grip handels, 6'', tapered jaws 4Workshop STORES - E/I


28 Wire Stripper Fully automatic wirestripper 0.08-2.5 sq.mm 6Workshop STORES - E/I


29 Heat Gun Standard Heat Gun 240V ac, for industrial use by electrical tecnician 2Workshop STORES - E/I


30 Portable Gas TesterHoneywell X5 Multi-Gas Detector - O2 - LEL - CO - H2S - SO2 - Rechargeable Batteries - Sampling Pump



E&I 31 Ultrasonic Leak Tester SDT FluxUS Ultrasonic leak detector 2Workshop STORES - E/I


E&I 32 Frequency Counter

Example: FCX 2000 intrinsically safe frequency calibrator, Range 0.01 to 10KHZ, Pulse, Frequency, RPMPredetermining / measuring frequencyPredetermining / measuring pulsesMeasuring/simulating number of revelutionsTesting NAMUR-initiatorsPredetermining measuring timestransmitting measuring static levels ranging form 0.01Hz to 10kHz with duty factors from 1 to 99%intrinsically safe



E&I 33 LCR Meter

Test frequency: 12Hz to 200kHz, 504 stepsBasic accuracy: 0.05%Test level signals: 5mV to 1.275V (5mV step) Impedance/resistance R : 0.00001 Ω to 99999 kΩCapacitance C : 0.00001 pF to 99999 µF Inductance L : 0.00001 mH to 99999 H Quality factor Q : 0.0001 to 9999Dissipation factor D : 0.0001 to 9999 Test modes : R/Q; C/D; C/R; L/Q; Z/θ; L/REquivalent circuit : Parallel or series selectableMemory : 100 memory blocks Test speed : Slow, medium and fastDC bias : Internal 2V, External 0-35VOperating Temperature : +10°C to +50°COperating voltage: 230V ±10%, 50Hz



34 Digital Multimeter

Precision 1000V, 440mA digital Multimeter measures a.c. and d.c. volts, a.c. and d.c. current, resistance, continuity and frequency.d.c. mA current source / loop calibrator / 20mA current source/ simulator / % of scale readoutTrue r.m.s. a.c. voltage measurement Frequency measurement to 20kHzMin./ Max./Peak Hold/Hold/Relative modes24V loop power supplyManual Step, Auto Step, Auto Ramp0% and 100% buttons to toggle between 4 and 20mA1200 Ohm drive capability on mA sourceHART mode setting with loop power incorporating 250 Ohm resistorExternally accessible batteryDiode test and Continuity Beeper Large dual display LCD4000 display count2 brightness settings for backlight Intrinsically safeExample:FLUKE-789



35 Megger MMC850 clamp meter, Stock No 495-5459 4Workshop STORES - E/I


36 Loop Tester

High resolution (0.001Ω) 2 wire testing + maxZ + (R1+R2)Backlit display2 wire loop tests: Phase to Earth, Phase to Neutral or Phase to Phase3 phase circuits with RCD protection can be testedTests radial circuits where the circuit does not return to the origin, even where only a phase and neutral contacts are available.10 second non trip loop test time with Auto test extension up to a further 10 seconds if noise is detected, to improve the accuracy of the testHigh current loop testing for supplies that do not have an RCD fitted AUTO START will start the loop test running as soon as the test leads are connected; No need to press the test button means much safer testingPFC Display up to 40kAVoltage and frequency measurement110 Vac systems including 110V centre tap to earth (55 V phase to earth) can be tested on the secondary winding.IP54 Weatherproof case Optional 10A fused 2 wired test leads and crocodile clip set Complies with IEC61010-1 300V CATIV safety standard and meets EN61557Intrinsically safeExample: Manufacturers Part No. LTW425



37 Current Simulator 4-20mA current simulator 2Workshop STORES - E/I


E&I 38 AC/DC Clamp Multimeter

Two a.c./d.c. true rms clamp meters1000A current measurementMin/max. measurementFrequency measurementDisplay hold keeps measurements on the displaySafety rating: EN61010-2-032, 600V Cat III Large 6000 count back-lit displayTrue rms measurementsIn-rush current measurement600Vac/dc voltage measurementLightweight design with ergonomic control layoutLarge 42mm jawsContinuity beeper below 30ΩAuto shut-off to maximise battery lifeExample: Fluke 337 1000 Amp True RMS AC/DC Clamp Meter



39 Signal GeneratorFrequency range 0.1Hz to 10MHz (sine & square wave), 150MHz Frequency Counter, Output Range 10Vpp(into 50Ω load)



E&I 40 Oscilloscope

1 GMHz Bandwidth 2.5 GS/s maximum real-time sample rate, with sin(x)/x interpolation 10Msamples per channel memory depth 4 Channels 4 ea P5100 Passive Probes included 10.4" XGA Color Dislpay Intuituve front panel zoom and pan controls for simple record length measurments Easy "bookmarking" for quick navigation between marks Multi-language User Interface Front Panel USB and CompactFlash Rear Panel USB 2.0 Device Port for Direct PC Control of Oscilloscope Using USBTMC Wave Inspector Controls Provide Unprecedented Efficiency in Waveform Analysis

Built-in Ethernet port

Example: Model: DPO4104, With up to 1 GHz bandwidth and 5 GS/s sample rate.



E&I 41 Handheld ThermometerProbe Type K , Minimum Temperature Measurement -50°C, Maximum Temperature Measurement 950°CIntrinsically Safe



42 Digital ManometerModel: 350 Smart Manometer Series, Pressure ranges: vacuum to 2000 PSI, Differential, vacuum, gauge and absolute pressure sensors.



43 Power Supply Unit Model: K24-STR-24 30VDC-10A 6Workshop STORES - E/I


E&I 44 Cable Tester Continuity tester for twisted pair cables & coaxial cables 3Workshop STORES - E/I


45 Fibre Optic Test Equipment Part no. FT500 3Workshop STORES - E/I


46 Portable Vibration Meter 2Workshop STORES - E/I


47 Decade BoxesAn 8 decade resistance box providing reference resistance from 1Ω to 111MΩ. Part No: A19000300.



E&I 48 Auto TransformerModel: CMCTV 10, Input voltage: 230, 240VAC, Output voltage: 0-115% of input, Output current: 10A.



49 Magnifying Lens 2Workshop STORES - E/I


50 Measuring Tape Metric 3 meters 10Workshop STORES - E/I


E&I 51 Spirit Level 310mm long, frame material cast iron 1Workshop STORES - E/I


E&I 52 Micrometer 0-25 mm outside micrometer 2Workshop STORES - E/I


E&I 53 Vernier Calliper Digital/Vernier calliper 200mm, intrinsically safe 2Workshop STORES - E/I


E&I 54 PCB Construction Kit Dot matrix die 12Workshop STORES - E/I


E&I 55 Temperature Calibrator

Portable Dry Block Calibrator. Temperature range -35°C to 650°C in three ranges

Example: Model: FAST-CAL HIGH, 35 - 650degC



56 Dead Weight Tester

Max pressure: 300bar558 Pneumatic Dead Weight TesterStandard Accuracy to 0.015%Class "S" Accuracy to 0.008%Ranges from: 1 to 120 bar100 to 12000 kPa 10 to 1600 lb/in²kg/cm² 1 to 120



57 Digital Pressure Calibrator

Pressure calibrator, the nominal accepted specs are:0-7barPressure/vacuum pump -850mbar to 20bar Integral combined pressure/vacuum pumpDual display simultaneously indicating input and output values4 to 20 mA loop test, Leak test, max/min and filterAmbient temperature measurement26 Selectable pressure unitsPressure range accuracy: ±0.025%Two way PC communication for transferring procedures and results Error analysis with pass/fail status and graphs Supplied with Intecal for Industry calibration management software (25 tag limit)



58 Multifunction Calibrator

0 - 24mA Source & Sink, 0 - 20mA & 4 - 20mA pre-set ranges, Voltage output 0 – 300mV, 3V, 10V & 15V, Resistance 5-2000Ω, Simulation RTD temperature sensors, Simulate extensive range of thermocouples including J,K,T,E,R,S,B,L,U,N with internal or external cold junction compensation, Frequency square wave pulse generator.



59 Loop Calibrator

Built in 24Vdc power supply loop, mA and % displayed simultaneously, as linear or square root (flow), Measurement/generation 0 - 24mA DC, Predefined values for the quick testing of linear loops, flow loops and the control of valves, HART transmitter compatible.



E&I 60 Handheld Communicator Field communicator Emerson 475 2Workshop STORES - E/I


62 Valve Test Bench

7,5 A semi automatic test bench, DN 15 to DN 100, Max test pressure 80 bar, 60bar respectively

Semi Automatic valve test bench suggestion - http://www.hydratron.co.uk/media/html/valve_rigs.htm?3 OR for a lower cost system a manually operated version is available (http://www.hydratron.co.uk/media/html/hand_pumps.htm) fittings to connect to valves are required but should be available from Hydratron. Suggest Hydratron is contacted.



E&I 63 Pressure Transmitter (HART)

Differential Pressure Transmoitter, HART protocol, Measurement span: 100 to 10000mmWCMeasurement Type Differential, Gage, Absolute, Level, Flow Output 4-20 mA HART, FOUNDATION™ fieldbus, PROFIBUS PA, 1-5 Vdc HART Low Power Reference Accuracy ± 0.065% of span with 0.04% Optional Total Performance ± 0.15% of span Long Term Stability ± 0.125% of URL for 5 years Rangedown 100:1



E&I 64 Pressure Transmitter (FF)Differential Pressure Transmoitter, Fieldbus protocol, Measurement span: 100 to 10000mmWC



E&I 65 Valve Positioner Fieldbus protocol 2Workshop STORES - E/I


66 RTD SensorPT 100 / PT 200 / PT 500 / PT 10001 OF EACH



E&I 67 Temperature Transmitter

Temperature transmitter, Fieldbus protocol

Digital Accuracy + 0.10° C (+ 0.18° F) for Pt100 RTD D/A Accuracy + 0.02% of span Ambient Temperature Effects 0.003°C per 1.0°C (1.8°F) change in ambient (Pt100 RTD) Stability + 0.1% of reading or 0.1° C, whichever is greater for two years for RTDs+ 0.5% of reading or 0.5° C, whichever is greater for five years for RTDs Input 2-, 3-, and 4-wire RTD, thermocouple, millivolt, or ohm Output 4-20 mA/HART or FOUNDATION Fieldbus signal



68 Thermocouple Sensor K'type thermocouple, Range: -200 to 1250 degC 2Workshop STORES - E/I


E&I 69 Turbine Flowmeter Daniel Series 1500 Liquid Turbine Meter 2Workshop STORES - E/I


E&I 70 Vortex FlowmeterVortex flowmeter, HART protocol, ANSI class 150# flange process connection, Nominal size: 25mm.



E&I 71 Magnetic Flowmeter Magnetic flowmeter, Nominal size: 25mm. 2Workshop STORES - E/I


E&I 72 Pressure Gauge (4 (Diff types)1) Bourdon type pressure gauge, Range 0-4bar, 2) intelliGAUGE Diaphragm ressure Gauge, Range 0-10 bar, 3) Vacuum gauge 4) Diaphragm seal pressure gauge.



E&I 73Temperature Gauge (3 (Diff types)

1) Temperature gauge, Range: 65 to 400degC, 2) Themperature gauge with thermowell, 3) Capillary type



74 Pressure Switch Range 0 to 4 bar 1Workshop STORES - E/I


E&I 75 Temperature Switch Gauge Temperature Switch Gauge, Range -20 to 200degC 1Workshop STORES - E/I


76Eddy Current Proximity Probe & Driving Unit

Probe Type: PRS-08 3Workshop STORES - E/I


E&I 77 Vibration Transducer

PZDC2 Velocity Transmitter Operating Voltage......16 to 32 volts DC.Output signal 1........... 4-20mA proportional to output ranges.Output signal 1........... 100mV/gOutput 1 ranges.......... 0 – 15mm/s, 20mm/s, 25mm/s & 50mm/sOutput 2 range ........... ±50gAccuracy .................... ±5% both outputsFrequency Range .......10Hz to 1kHz (1dB), 2.5Hz to 6kHz (3dB)Transverse sensitivity ...... Less than 5%Temperature sensitivity .... 0.05% per ºCResidual electrical noise .... Less than 0.2mg (2.5Hz to 10kHz)Signal transmission ............ Three-wire system, electrically isolated from body up to 500Vac.Weight................................ 225 gms (nominal)



78 Ball Valve Ball rotary control valve 1Workshop STORES - E/I


79 Plug ValveFlanged or flangeless eccentric plug valve with reversible metal seat ring and splined shaft.



80 Butterfly Valve Elastomer Lined Butterfl y Control Valve, Actuator model: 54R-21B00. 1Workshop STORES - E/I


E&I 81 Relay

Relay, DPST-NO type.Example: G4W-1 PCB Relay, DPST-NO type.Relay Type: General PurposeMounting Type: Through Hole Termination Style: PC PinCircuit: DPST (2 Form A)Contact Rating @ Voltage: 15A @ 250VACCoil Voltage: 24VDCControl Off Voltage (Min): 2.4 VDCControl On Voltage (Max): 19.2 VDCCoil Current: 33.3mACoil Type: Standard



82 Solenoid Valve

Model: 2S160-1/2, Port size: 1/2"NPT, Service: Air, Liquid, Oil, Water,Direct Lift Diaphragm, Normally Closed , Two Way Diaphragm, 304 Stainless Steel Solenoid Valve, Temperature: 14 -176 °F (-10 TO 80 °C) (with NBR Seal), Pressure: Vacuum to 150 PSI.



83 Cut-away Control Valve 5009 Control Valve 2” Flanged + diaphram actuater + valve positioner 1Mechanical Classroom - B

Building

E&I 84Lifting Equipment, Mobile, Hydraulic (Capacity 1 t)

Same as mechanical shop unit 1E/I Workshop - Main

Building - A

E&I 85 Drilling MachineDrill capacity 25mm, Spindal stroke 125mm, Spindal taper 3MT, Table 430mm X 430mm, 1.5HP Motor, 3PH 380v supply, Speed range 125 to 2580 rpm.

1Electrical Workshop - Main

Building - A

E&I 86 Grinding MachineBench type, electric driven, two wheels 150 mm diameter (roughing and finishing)Accessories:Wheel guards, eye protecting shields Adjustable work rests

1Electrical Workshop - Main

Building - A

E&I 87 Battery Charger (Static) Input:220-240 V (ac) 50-60 Hz; Output:6/12/18/24/36 V and 0-5/10/15/20 A 1Workshop STORES - E/I


88

Bearing HeaterInduction Type, Temperature Controlled to 100°C Automatic Demagnetizing

Capacity : Diameter 10 mm, external 250 mm. Width of bearing maximum 100 mmInput : 220/240 V (ac) 50/60 Hz 15 A maximum



89Bearing Puller - Mobile Hydraulic, Two Arm Type

Mobile hydraulic, two arm type. Capacity : 40-250 mm diameter bearings 2Workshop STORES - E/I


90Bearing Puller - Gear Race and Sprocket Type, 3 Arm

Capacity : 150 mm diameter bearings 2Workshop STORES - E/I


E&I 91Extractor (Internal Bearing) - Gear Race and Sprocket Type, 3 Arm

Capacity : 115 mm diameter bearings 2Workshop STORES - E/I


95 Socket Set 1/2 Inch Drive - Metric Set, General Service use, 12-Point (35 pcs.) 3Workshop STORES - E/I


96Socket Set 1/2 Inch Drive - Imperial

Set, General Service use, 12-Point (35 pcs.) 3Workshop STORES - E/I


E&I 97Spanner Sets up to 1" and 25mm - 48 Piece. Open-ended and Ring (Inc. Offset)

48 Piece Set. Comprehensive set of Open End and Ring Spanners in a heavy duty roll. Includes the most popular sizes. Chrome Vanadium Steel with polished heads. 20 x combination 6-25mm, 12 x combination ¼” - 1” AF, 8 x double open end 6 x 7 - 20 x 22mm, 8 x ring end 6 x 7 - 20 x 22mm.



98 Adjustable Spanner 6" 2Workshop STORES - E/I


E&I 99 Adjustable Spanner 10" 1Workshop STORES - E/I


100Allen Key Sets - L Type with Ball End - Metric




101Allen Key Sets - L Type with Ball End - Imperial

9 Piece Set. Very tough screwdriver bit material will not round-out in hex screws or bolts. Ball End 1/16 to 3/8 " keys and clip.



E&I 102 Hacksaw

Designed for 12" (300mm) blades. Allows very high blade tension for accurate and exact kerfs. Spring tensioned blade loading mechanism, strong rectangular back section for blade storage with an easy to handle retaining screw. Positions for normal flush cutting or 55° for angle or horizontal cutting. Can be used as a compass saw.



E&I 103 Junior HacksawsSquare bar steel frame, with comfortable moulded plastic handle, enclosed for finger protecion, incorporating a quick, easy lever action blade locking and change feature.



E&I 104Maintenance File Set - 4" Second Cut

Precision files manufactured in accordance with SQS quality management system to ISO9001/EN29001Files are manufactured from high-grade chrome steel, hardened to 65 HRC for greater cutting capactiy and prolonged tool lifeIdeal for use in limited access areas, these files are designed for engineers who require a file larger than needle, but smaller than engineersOverall length 4 inches in Cut 2, fitted with wooden handles for safe useSet comprises one each, flat, warding, square, three-square, round, and half-roundSupplied in a PVC wallet



E&I 105Engineers File - 300mm Smooth Cut - Half-round


10


benches

E&I 106Engineers File - 300mm Smooth Cut - Round


10


benches

E&I 107Engineers File - 300mm Smooth Cut - Square


10


benches

E&I 108Engineers File - 300mm Smooth Cut - Three Square


10


benches

E&I 109Engineers File - 300mm Smooth Cut - Pillar


10


benches

110 Hammer Set (Ball Pein) Set, Hammer, Hickory Handle, - 8,12 oz - 4 pcs. 1Workshop STORES - E/I


111Soft Faced Mallet/Hammer (Nylon Face)

1 Kg with replaceable faces 1Workshop STORES - E/I


E&I 112 Bronze Drift Punch 1Workshop STORES - E/I


113 Vee-Blocks

VEE BLOCKS with ClampsCapacity 39.6mm/31.1mm Clamping Screw Material Chrome Steel Dimensions 70(L)x64(W)x45(H)mm



E&I 114 Vee-Blocks100 X 100 mm, fine grain cast Iron, buy in pairsExample: Moore & Wright item number MW 213



115 Pliers - Adjustable Joint Pliers adjustable joint -Interlocking Channel, Industrial Finish, 9 1/4" 2Workshop STORES - E/I


116 Cutters 4 1/4" Cutters, Diagonal Grip 2Workshop STORES - E/I


117 Standard Pliers - Lineman 7 3/8" (7 3/8"). Machined cutter heads for perfectly matched blades. Heads are induction hardened. Additional gripper teeth behind the heads. Industrial finish and red vinyl covered handles.



E&I 118 Locking Pliers (4 in Set)

Set, Locking Pliers, Standard Grip, 4 pcs.Consists of 5" and 10" locking pliers with wire cutter, plus 6" long nose locking plierGuarded release mechanism is an important safety feature - helps keep work safe and secureSupplied in plastic tool roll pouch



119 Long Nose Pliers 2Workshop STORES - E/I


120 Needle Nose Pliers 2Workshop STORES - E/I


121Retaining Ring Plier Sets (Circlip Pliers)

Set, Pliers, Retaining Ring, 2 pliers 2Workshop STORES - E/I


E&I 122Screwdriver Sets - Flat Tip Impact Screwdrivers - SETS - 5 per set

Heavy, square cross-section blades, matt chrome plated with gun finished tipsShatterproof handles with heavy steel striking plate for impacting. 5 per set 3 to 11mm tip size



E&I 123Screwdriver Sets - Philips SETS - 5 Per Set

Pro Screwdrivers. Tip sizes No 0, 1, 2 and 3. Hardened tips. 3Workshop STORES - E/I


124 Screwdriver Sets - Torx Pro Screwdrivers. Tip sizes TX6, TX8, TX10, TX15, and TX20. Hardened tips 1Workshop STORES - E/I


E&I 125 Screwdriver Sets - Posidrive High quility Screwdrivers. With range of tip sizes. Hardened tips 1Workshop STORES - E/I


126Jewlers/Instrument Screwdriver Set

Type: Flat Point, Quality miniature precision jewellers screwdrivers set with nickel-plated bodies, blackened steel shafts and revolving heads for precise accurate control



129Insulation & Continuity Tester - 500 V (dc)

Type : Analogue/Digital battery operated voltmeterRange : Insulation 0-200 MOhm; Continuity 0-2 Ohm, 0-200 Ohm; Voltage 0-600 V (ac)



E&I 131 Insulation Tester - 1000 V (dc)

Type : Analogue, battery-operated, voltmeterRange : 250/500/1000 V (dc); Insulation 0-20 MOhm, 0-500 MOhm; 0-1000 Mohm; Voltage 0-600 V (ac)Example: Megger MIT310



E&I 132 Insulation Tester - 5 kVDC

Portable, microprocessor controlled 5kV insulation tester fitted into a rugged IP53 case Large backlit LCD screen with digital display & bargraphInsulation, voltage, capacitance and leakage current testing30 kΩ to 10 TΩ resistance range4 predetermined test voltages: 500/1000/2500 and 5000 VProgrammable test voltage: 40 to 5100 V in 10 V or 100 V steps suitable for many applications including electrical switchgear and telecoms applications Qualitative insulation analysis: automatic calculation of DAR, PI and DD (Dielectric Discharge) ratios1 to 60 minute timed tests to analyze the quality of the insulationComplies with IEC61010-1 CAT III 1000VRechargeable NiMH batteries with integral charger



136Earth Leakage Circuit Breaker Tester

Tripping current 10 / 20 / 30 / 100 / 300 / 500mA Fault condition setting x1/2, x1 & x5 Fault trip time 2000ms, 40ms (x5) Low set resolution 1ms (x1/2, x1) & 0.1ms (x5) Trip time accuracy ± (1% rdg + Dgts) Operating voltage 230V ±10%, 50/60Hz Withstand voltage 3000V AC for 1 minute Operating temperature & humidity 0 to 40°C below 80% RH to be supplied with test leadsIntrinsically Safe



E&I 138Live Conductor Indicator & Phasing Tester

Nominal System Voltage Range, 50/60Hz (phase to phase)1 off : 2.4 to 6.9 kV, kV Indicator Markings: , 1.4, 2.4, 4.2, 6.9 Mechanical Style: Two fixed-length poles with hand guards Poll Length: 39 in

1 off: 6.9 to 34.5 kV kV Indicator Markings: 0, 4.2, 7.2, 13, 25, 35 Mechanical Style: Two fixed-length poles with hand guards Poll Length: 56 in.cable length between pole 59in

example: 1 off Megger DETEX 514500-1 & 1 off Megger DETEX 514500 514500-2



E&I 139 Phase Sequence Indicator Phase sequence/continuity indicator 600V 50/60 Hz 1Workshop STORES - E/I


E&I 140Multi-Range Meter (Analogue Type)

Analogue type; complete with leads, safety clips and carrying case, including the optional accessory Test leads with fused prods (660 V (ac) / 500 mA fuse, 50 kA breaking capacity)Ranges : 0-1000 V (ac)/(dc), 0-10 A (ac)/(dc); 0-20 MOhmImpedance : All dc ranges 20 kOhm/V, Above 30 V ac 2 kOhm/V



E&I 141 Multi-Range Meter (Digital Type)EXAMPLE: Make : Megger Instruments; Type : AVO300 multimeter with fused leadsAlternative:Make: Fluke ; Type: Fluke 289 Digital Multimeter with fused leads (as per GS38)



E&I 143 Clamp-on Volt/A Ohm Meter

• DC and AC current and voltage• 600 A and 600 V• Resistance and continuity• 31/2 digit, 4000 count display with backlight• High resolution digital bargraph• Peak, min/max and data-hold functions• Zero-offset REL mode for comparative measurements• Supplied complete with test leads and carry case• IEC61010 CAT III 600 VIntrinsically Safe



E&I 144Clamp-on Watt Meter & Multimeter

Power Quality Clamp-on Meter (Range 1000A)a.c. voltage 400µV/0.1V 750V/1V ±(1.0% rdg+5d) 50 to 500Hz d.c. voltage 400µV,/0.1V 1000V/1V ±(0.7% rdg+ 2d) a.c. current 400µA,/0.1A 1000A/1A ±(1.5% rdg+ 5d) 50Hz/60Hz ±(1.9% rdg+ 7d) 50Hz/60Hz d.c. current 400µA,/0.1A 1000A/1A ±(1.0% rdg+ 3d) ±(1.9% rdg+ 7d) Resistance 400µO/0.1O ±(1.0% rdg+ 3d) Frequency counter 20 to 400Hz/1Hz ±(0.1% + 2d) @ 5V rms max Intrinsically Safe



145 Portable Appliance TesterPortable, mains operated, Earth bond test, Insulation test, Flash test, Load testIntrinsically Safe



E&I 146 ThermometerDigital display with probe for surface temperature measuringRange : -50 to +400 °C Intrinsically Safe



E&I 147 Light Meter

Minimum Light Level 0 Maximum Light Level 50000lux Resolution 1; 10; 100 Lux Sensor Type Photo Diode, Correction Filter Accuracy ±4% +2 Digits Intrinsically Safe



148 Hand Tachometer Multi-range optical tachometer, for general purpose non-contact measurement of RPM, cycle time, total count, duration of total count.



149 Variable Transformer Portable variac autotransformer, 10A 1Workshop STORES - E/I


E&I 150 Stopwatch 2Workshop STORES - E/I


E&I 151Secondary Current Injection Test Set

Analogue display current, electric timer, 0 - 999.999 sRange : Current output 0 - 10 A/85 V, 0 - 40 A/25 V, 0 - 100 A/10 VVoltage ouput 0 - 250 V/3 A (ac), 0 - 350 V/2 A (dc) Terminals : 110 V/0..3A, 20-220 V/0.3ASuitable for 220 V (ac), 50 Hz, Weight 16 kg Intrinsically Safe



E&I 152 Clamp-on MultimeterDigital type, complete with test leads, batteries and case.Peak reading lock facilityMake: Fluke; Type: Fluke 337 true rms ac/dc clampmeter,1000A



E&I 153 Voltage Tester Range:0-750 V (ac)/(dc); Make:Benning; Type:Duspol Digital 1Workshop STORES - E/I


E&I 154 Volt & Ohm ProbePencil-type DMM with PenlightMake:Hioki; Type:Pencil HiTESTER 3246



155 Compression Tool Cable lugs/connectors, hand-operated 3Workshop STORES - E/I


156 Set of Soldering Irons 12Workshop STORES - E/I


157 Isolating TransformerVoltages 220/220, 240/240 (or other local voltage), with socket outlet to IEC 309, enclosure protection IP 55 (IEC529). Ratings: 250, 630, 1600 VA - 1 x 16 A, 3 pole.



E&I 158 Earth Leakage Circuit BreakerEncapsulated, plug-in type, IP 30, (round, 2 pole, scraping earth) with flexible lead and rubber connector (round, 2 pole, scraping earth). Rating : 30 mA, 16 A, Voltage : 250 V (ac) 50 Hz



E&I 159 Hand LampIndustrial type, 50 V, vibration resistant, double insulated, lamp max 200 W tungsten GLS, lampholder ES butyl rubber enclosure, polycarbonate cover and chromitised suspension hook, protection IP 65. cable length 15m

Workshop STORES - E/I Section - Main Building - B

E&I 161 Cut-away Model

Cut-A-Way Electric Motor, Single Phase Induction; Model no. 9301

Three phase electric motor to be sectioned. Suggest .25 KW. I can not find a supplier on the internet


Building

162 UPS SystemUPS Unit for demo purposes - http://uk.farnell.com/tripp-lite-power-protection/bc-pro-600/uninterruptible-power-suppy-ups/dp/1091969



E&I 163 Hand Lamp

CE marked to ATEX DirectiveEN50014, EN50019, EN50020, EN50281-1-1 Apparatus StandardDust ignition protected for use in zones 21 and 22Halogen bulb with high intensity spot beamBattery gives up to 7 hours duration with deep discharge protectionUses 3·75V, 2·8 Watt Halogen bulb, 100 hours lifeWall mountable lamp charger and rechargeable battery available separatelySupplied with non-spillable, rechargeable battery and detachable shoulder strap



165DIN 2275 Metric Feeler Gauge Set

Used for inspection of Ex d equipment, All sets have blades manufactured from hardened and tempered steel, and have mild steel cases & calibrated



166Miscellaneous Used Electrical Equipment (for Demonstration Purposes)

Electrical items (switches, contactors, auxiliary relays, limit switch. PBS etc) and second hand electrical equipment (motors, small transformers, HV and LV switches, small synchronous generators, etc), used for demonstration purposes and development of practical maintenance skills (inspection, disassembly/assembly, etc.)


Section - Main Building - BSuggest used equipment.

E&I 167 Motor Test Bay

The motor test bay is a segregated area of the electrical workshop with facilities specifically designed for the safe testing of electric motors and will require, typically, a floor area of 18 m2.The motor test bay shall be fenced-off from the remaining workshop area with the control and monitoring panel located outside the fence within visual range. The general requirements for the motor testing facilities are listed below.

Steel mesh fence with sliding gate access. Steel bed plate (fixings for clamps and bolts for vertical and horizontal

motors). Socket outlets (3) 3 P.E. for connection of motor under test. Switchboard Warning lamp (Illuminated during testing). PBS (Start, stop & Ampermeter incorporated for each motor installed in Test

Bay Emergency stop push button, mounted inside motor test bay for each Motor

installed. Common earthing busbar (wall mounted inside test bay). 3 induction motors will be installed in the motor test bay, through socket

outlets and connected to MCC panel

1

E&I 168 One (1) Incoming Feeder 125ACircuit breaker manually operated with tripping coil, Instantaneous overcurrent protection implemented, andcontrol & measuring circuits

1

E&I 169 Two (2) Motor FeedersMotor feeder will consist of manually operated circuit breaker with instantaneous overcurrent relay protection implemented; contactor, thermal overload relay, control relays and PBS and signal lamp

2

E&I 170 Two (2) Motor FeedersMotor feeder will consist of manually operated circuit breaker with instantaneous overcurrent relay protection implemented; contactor, PLC based Simocode or similar protecting relay, PBS/SS and signal lamps.

2

E&I 171Two (2) Induction-type 3-Phase Electric Motors, 2 kW, 1480

Additionally electric motor induction type 3 phase 2kW 1480 R/min, Local Control Panel (start, stop and SS) and Push Button Switch (start, stop and EPBS mushroom type). Voltage and frequency as per local condition. Connection of the motor on MCC panel will be through socket outlets 32A Exd type

2

E&I 172 Four (4) 10 kW Power FeedersPower feeders equipped with circuit breaker, contactor, relays, PBS and signal lamp. In addition one Local Control Station (start & stop) will be supplied.

4

E&I 173One (1) MCC Variable Frequency Drive Section with 2 kW Motor

In addition, Local Control Panel (Start, stop and amperemeter) and EPBS (mushroom type) will be supplied. Motor will be installed in Test bay and connected through socket outlets Ex type 32 A

1

Items E&I 168 to 173 are part of item E&I 167Electrical Workshop - Main

Building - A

174Single and Three Phase AC Generators

Second hand unitshttp://www.machinemart.co.uk/shop/product/details/clarke-fg3050-petrol-powered-generator/path/petrol-driven-frame-mounted-site-generators

Type Dual Voltage Rated Power Continuous 2000VA Maximum Output 2200VA Fuel Tank Capacity 15L Noise Level 68dBA Output Voltage 110/220/230/440V Weight 45kg Engine Type 4Stroke



175Associated Generator Control Equipment



176 Associated Cabling and WiringWorkshop STORES - E/I


E&I 178Single Phase Induction and Variable Speed Motors

Second hand unitsAsynchronous Single Phase Electric Motor with Squirrel Cage Rotor - Enclosed Construction - External Ventilation - 2 pole - 3000 rpm - 50 Hz - 0.75 KW AND



E&I 179Three Phase Induction and Variable Speed Motors

Second hand unitsAsynchronous Three Phase Electric Motor with Squirrel Cage Rotor - Enclosed Construction - External Ventilation - 4-6 pole - 1500 and 1000 rpm - 50 Hz - 0.75 KW AND Slip ring electric motor Asynchronous Three Phase - Enclosed Construction - External Ventilation - continuous duty - 8 pole 750 rpm - 50 Hz - 0.75 KW should be foot-mount



E&I 180 Auto

Second hand units

AutoTransformer - Step-Up/Step-Down Auto TransformersAutowound transformers for step-up or step-down of mains voltages at 50/60Hz. •Compact construction Full varnish impregnation Fully shrouded Four-hole fixing for permanent installation Terminal blocks with protective covers (except 50VA which has leads) 100% electrical and flash tested (2kV winding to core)Tested in accordance with EN61558 - http://uk.rs-online.com/mobile/search/searchBrowseAction.html?method=getProduct&R=0504199



181 Double Wound Transformer Second hand units 1Workshop STORES - E/I


182 Isolating Transformer Second hand units 1Workshop STORES - E/I


184Single and Three Phase Transformers

Second hand unitsVA Rating Continuous 480 Input Voltage 400//415Vac Output Voltage 0 - 112% of Vin Output Current 2A

Single phase included in items 180 to 183 - Three phase example for demo use required suggest contacting SKOT (http://www.skot.co.uk/page06.htm) for lowest cost example.



185 Invertors

Supply Voltage 3 Phase, 380 to 480V Power Rating 2.2kW Current Rating 5.6A IP Rating IP20 Invertor for motor speed control - max 1KW - ACTIVE A.C.DRIVE type. Supplier www.motors-direct.co.uk OR/AND ACS350 3 Ph inverter, 380-480V, 2.2kW - http://uk.rs-online.com/mobile/search/searchBrowseAction.html?method=getProduct&R=6211442



E&I 189 Discharge Light Dicscharge light 70-100w in IP65 encluser 6Workshop STORES - E/I


190 FloodN16122 - EEx nA twin fluorescent light fitting for 18 Watt Lamps supplied by WALSALL Ltd - http://www.walsall-ltd.com/product.php?prod=7&data=yes&topSection=1



E&I 191 Fluorescent

Fluorescent type with UPS incorporated suitable for Zone 1 , 100 Watt Sodium lights , 240 VoltsExamples: Walsall Ltd - ORB/100HS - 100 Watt Sodium lights - http://www.walsall-ltd.com/product.php?prod=9&data=yes&topSection=1



E&I 192 Emergency Lighting

Maintained/Non-Maintained Combo: Easily wired for both non-maintained or maintained application 100 Lumens IP65 (Weatherproof) Polycarbonate base Prismatic diffuser Dimensions approx : (HxWxD): 100x370x140mm Complete with lamp Suitable for incorporation into an emergency lighting system complying with BS5266-1:2005

Example supplier - http://www.safelincs.co.uk/Bulkhead-Emergency-Light-JP8M-JPX8M/?fdb=true



193Associated Controls, Wiring and Connectors

Junction boxes - E115001 - http://www.walsall-ltd.com/product.php?prod=136&data=yes&topSection=31. Terminal boxes - GL3 - http://www.walsall-ltd.com/product.php?prod=124&data=yes&topSection=31 Terminal boxes - SL2 - http://www.walsall-ltd.com/product.php?prod=56&data=yes&topSection=31 Terminal boxes - http://www.walsall-ltd.com/product.php?prod=79&data=yes&topSection=31 Terminal box - ASMT150 - http://www.walsall-ltd.com/product.php?prod=76&data=yes&topSection=31 Local control - E030166 - http://www.walsall-ltd.com/product.php?prod=183&data=yes&topSection=53 Distribution box - DBD150/91/CI - http://www.walsall-ltd.com/product.php?prod=226&data=yes&topSection=85 Distribution box - DBD150/62/CI - http://www.walsall-ltd.com/product.php?prod=226&data=yes&topSection=85 Plug and Socket - DXN3A - http://www.walsall-ltd.com/product.php?prod=142&data=yes&topSection=64 Reducers (selection from - http://www.walsall-ltd.com/product.php?prod=238&data=yes&topSection=6 Lighting Transformers 240v to 110v - http://www.walsall-ltd.com/product.php?prod=244&data=yes&topSection=0 Cable glands to suit above - M20 - http://www.a-belco.co.uk/Hazardous/Downloads/Products/glands/Cable%20Gland%20Overview%20Leafle%20rev%202a.pdf Cable barrer glands - selection to suit above - M20 - http://www.a-belco.co.uk/Hazardous/Downloads/Products/glands/Barrier%20Gland%20Overview%20Leaflet%20rev%201a.pdf



E&I 194Circuit Breakers (Selection of, 4-6 types 6 of each type)

Switch Circuit Breaker: Suitable for Zone 1, Switches with an off position have a padlock 'off' facility as standard, fitted with a 20 - 25 mm Ex e cable gland. 250V max, 15 Amp max, conducter size 2.5mm max Example: http://www.walsall-ltd.com/product.php?prod=243&data=yes&topSection=4 Switch - LCA103 - http://www.walsall-ltd.com/product.php?prod=150&data=yes&topSection=4 Breaker - EFD3 - http://www.a-belco.co.uk/Hazardous/Products.php



E&I 196Process System Control Valve Assemblies

Including valve, pneumatic actuator & positioner. DN 50 (around 2''),all other specs are not important since it will never be connected to any other equipment, it will be just used for training purposes.

EXAMPLE: http://www2.emersonprocess.com/en-US/brands/fisher/ControlValves/slidingstem/genchemservglobevalve/GX/Pages/FisherGX.aspx OR http://www2.emersonprocess.com/en-US/brands/fisher/ControlValves/slidingstem/genchemservglobevalve/RSS/Pages/FisherRSS.aspx



197Pneumatic Process Controllers and Associated Input/Output Components

Including controllers, recorders, converters/regulators. Second hand 3Workshop STORES - E/I


E&I 61Instrument Test & Calibration Bench

Integrated Instrument Calibration Test bench. (12 station)To include the following features;Basic benches to includeVariable AC power suppliesVariable DC power supplies (inc 4-20 MA, 3-15V, 12, 24, 110)Integrated transformer and distribution boardCompresses air supply with standard regulator.Precision compressed air regulator and air filtration

1 bench with additional featuresOscilloscopes Function generator Pressure/vacuum calibrator Process calibrator mV/mA calibrator


Main Building - A

8

Storage Cupboards 1800 x 1000 x 500mmQuarter louvre backQuarter tool panel2 drawer unit

6Instrument and Electrical

Workshops - Main Building - A/B


8000 USD


MECH 177

Pipe Wrenches Wrench, Pipe, External, Standard Handle, 10" 16

MECH 178

Pipe Wrenches Wrench, Pipe, External, Standard Handle, 24" 5

MECH 116

Pipe Threading Machine (Electric)

Pipe Threading Machine - High performance machine for threading, cutting, deburring, threading of nipples, roll grooving. For installation, metalworking, industry. For job site and workshop.Pipe threads 1/16–2", 16–63 mm. Bolt threads 6–60 mm, 1/4–2". Pipe threads with 4" automatic die head 21/2–4". Also capable of threading plastic covered pipes. Pipe grooving with roll grooving attachment DN 25–200 (300) 1–8" (12").Automatic chuck. Universal automatic die head. Automatic lubrication and cooling.

1

MECH 117

Manual Pipe Threader with Dies. 1/8" to 2"

Hand die stock with quick-change die headsProven quality die stock with excellent threading capabilities.Pipe threads 1/8–2", 16–50 mm. Bolt threads 6–30 mm, 1/4–1".Steel ratchet lever, thickly plastic coated. Quick-change die heads. Indestructible quality dies.

2

118Pipe Vice on Stand (including Pipe Support)

2

MECH 119

Hydraulic Pipe Bending Set vice-mounted pipe bender designed for use with hydraulic steel tube between 6 and 18mm outside diameter. The unit comes with six interchangeable bending rolls, anvil, and bending lever

1

Floor standing Hydraulic Pipe and Tube Bender

Pipe bender suitable for bending pipes upto 2". Eg - http://www.bifabuk.co.uk/benders/rotary-draw-benders-150.php

1

Pipe Vices Bench mount 4Wire brushes

Basic Handtools are shared with those specified on the Mechanical Equipment List. Additional specific equipment is detailed below.

PIPEWORK EQUIPMENT


EQUIPMENT LIST

Appendix 6


______________

No EQUIPMENT DESCRIPTION QTY LOCATION NOTESMetal Guillotine Foot Operated Sheet Metal Guillotine - 1

additional equipment to be added should this programme be required

FABRICATION EQUIPMENT


EQUIPMENT LIST

Appendix 6


50,000 USD


Manual Arc Welder

400 amp industrial arc welder - •- 40 - 400amps (viewing window shows appropriate rod size & current selection).•Turbo fan cooling for extended duty cycle, & strong ventilated steel casing.•Accepts welding electrodes 1.6mm to 6mm.•Thermal overload protection with auto reset.•Power input 230/400v, 1ph up to 17Kw

11 Welding Workshop

Metal Inert Gas Welder170amp Metal Inert Gas welder for fabricating heavier, thicker mild steel structures, car chassis and, thanks to the multiple power settings and a minimum welding ampage of 30 amps

11 Welding Workshop

Tungsten Inert Gas Welder

•Electronically controlled power output - 22 to 140 amps DC•Accepts 1.6mm to 3.25mm dia. electrodes•ARC welds rutile, low hydrogen & stainless steel electrodes•Strong ventilated steel casing with turbo fan cooling to enhance duty cycle•Max. power input - 5.4kW at 230v AC•Automatic short circuit protection guards against electrical overload•Separate kits available for TIG & Arc welding

11 Welding Workshop

Plasma Cutter

•Slices through iron, steel, aluminium, copper and brass etc. up to 4mm thick•Electronic power control with thermal overload protection•Turbo fan cooling within ventilated steel housing to maximise operational duty cycle•Requires 4 cfm compressed air at 4.8-5 bar pressure•Includes air filter, regulator and pressure gauge•Input up to 7 Kw at 230v 1-phase

5 Welding Workshop

10 Metre Welding Hose Set•Each hose 10 metres in length•Maximum pressure 20bar•Conforms to BS5120:19787/EN559:1994 safety standards

11 Welding Workshop

Gas Welding/Cutting Kit

•Welding capacity 5/16", Cutting capacity 3"•Oxygen regulator with twin gauges & Acetylene regulator with twin gauges•2 colour coded gas hoses with flashback arrestors and standard 3/8" bsp connectors•Gas torch/mixer unit•3 welding plus 3 cutting nozzles•Tip cleaner & sparklight•All contained in a tough molded carry case

11 Welding Workshop

WELDING EQUIPMENT


EQUIPMENT LIST

Appendix 6

Flashback Arrestor for Oxygen

An essential in-line safety device for use where oxygen is combined with acetylene for the purpose of welding. Fitted directly to the oxygen regulator it prevents any flame from reaching the bottle as a result of back pressure.•HSE requirement for industrial useage•Ideal for use with the Clarke CGW1 gas welding kit

11 Welding Workshop

Welding Apron 20 Welding Workshop

Welding Curtain•Eyelet fittings with suspension rings & snap fasteners•Dimensions of replacement curtain (WxH) 1300 x 1800mm•Weight 1.8Kgs

15 Welding Workshop

Welding Cart

http://www.machinemart.co.uk/shop/product/details/gwc-1-welding-cart

•Accomodates Clarke MIG151TE & smaller hobby MIG welders, Arc welders up to 190TE & Plasma King 35•Sturdy steel construction•Heavy duty castors - 2 fixed, 2 swivel•Dimensions (LWH) 720x430x780mm

11 Welding Workshop

400gm Chipping Hammer•Chipping hammer with point•Chisel head and hickory handle

20 Welding Workshop

Wrap Around Welding Headshield

Including an 11EW lens, conforming to CE BS679, the wrap-around design of this headshield offers excellent protection when welding.

20 Welding Workshop

Magnetic Weld Clamp

Buy now Add to wishlist A unit comprising 2 powerful linked magnets and used for holding separate pieces of ferrous material in position at varying angles prior to and during welding.

20 Welding Workshop

Standard Welding Screen 10 Welding WorkshopWelding Clamps 'C' Type 50 Welding Workshop


______________________


Lifting Operations and Lifting Equipment - LOLER

Frame 1

Loft 1PropsPallet Truck 1WLL 1 tonne chain blocks x 6m height of lift 12WLL 2t chain blocks x 6m height of lift 1Bow shackles c/w safety type anchor pin WLL 4.75t 14Bow shackles c/w safety type anchor pin WLL 6.5t 2Bow shackles c/w safety type anchor pin WLL 3.25t 3Beam clamps c/w swivel shackle WLL 2t 4Lever Hoist WLL 1.5t x 1.5m height of lift 1Lever Hoist WLL 3t x 3m height of lift 1Rigging screws (Turnbuckles) WLL 1t end fitting Jaw & Eye 3Push Beam Trolley WLL 2t 1

SWR slings 10mm dia x Galv RHOL Soft eyes both ends x .5m x WLL 1t max 3

Master Links WLL 3.62t 2WLL 1t x 1m EWL Fibre Slings 3Tirfor Wire rope winch WLL 500kg c/w 20m SWR 2

LIFTING AND SLINGING EQUIPMENT


EQUIPMENT LIST

Appendix 6


______________________



SCAFFOLDING EQUIPMENT


EQUIPMENT LIST

Appendix 6


_____________________


1 Tower/Desktop Computers Dell Latitude D-830

2 Monitors Dell 19” 1908FP LCD Monitor / Viewsonic 19” LCD Monitor VA1918W (ariff)

3 Servers

Acer Server TT.G3BE0.HS2 Altos G330Mk2 SAS Xeon DC E3110 3.00GHZ/1333FSB/6MB, 2GB DDR II 800, DVD, SAS controller 4 port SAS/SATA Hot Swap backplane kit (SO.G33SA.005), NO HDD, NO FDD, EURO power cable, PS2 Mouse, 1xLAN Gbit onboard, NO KB, EasyBuild 8.0, 5 x Acer 250 GB SATA and Acer Altos SAS / SATA RAID Array

4 Networked Colour Printers

Heavy DutyRex Rotary Digital Color Multifunction – Model MP C 4000COPIER / PRINTER / SCANNERIncludes:-High Productivity, 40 ppm color and 40 ppm B&W copies/prints 1200 DPI RESOLUTIONWide Zoom range of 25 - 400%Paper Capacity 2 x 500 sheets, 1 x 100 sheets bypassA3 to A6 Automatic Reverse Document FeederDuplex unitMemory – 1,024MB & 160 GB Hard DiskIntel ProcessorScanner- 63 sheets per minute speedColor Network Print ControllerColor Network ScannerNetwork Interface BoardScan to email, Scan to Folder functionsCABINET

5 Laptops

Toshiba Tecra A10-11L LaptopCore2 Duo P8400 (2.26GHz) 1066MHz,2GB+1GB DDR2 (800MHz),250GB (5400rpm) SATA,15.4" WXGA TruBrite, DVD-Super-Multi (+-R DL),Intel graphics GM45,WiFi 11b/g ,Bluetooth,integr. 1.3Mpix WebCam, FingerprintSensor,TOSHIBA Assist & Presentation,TPM, Vista Business & XP DVD

IT EQUIPMENT and LEARNING RESOURCES


EQUIPMENT LIST

Appendix 6

6 Networked Laser Printer B&W

GESTETNER C7528nCOPIER / PRINTER / SCANNERTechnology - 4 drums tandem method, laser beam scanning, electro photographic printing & dual component toner developmentContinuous print speed - Black and whiteFull colour 28 prints per minuteFirst print speed - Black and white Less than 11 secondsFull colour Less than 12 secondsDimensions (W x D x H) 575 x 678 x 745 mmWeight 85 kgPower source 220 - 240 V, 50/60 HzDuty cycle 200,000 pages per monthProcessor Celeron 733 MHzPCL5c 300 x 300 dpi/600 x 600 dpi PCL6, Adobe® PostScript® 3™RPCS™Standard 256 mb Maximum 511 MB OptionDrivers - PCL5c/PCL6/RPCS™Adobe® PostScript® 3™2 x 500-sheet paper trays1 x 100-sheet bypass tray3,100 sheets 500 sheets face downA5 - A3,A5 - A3 oversize 60 - 105 g/m² & 60 - 163 g/m²

7 Class Room Data Projectors 3M Over Head Projector 2660 Portable8 Projector Screen Sony VPL-CX76 Front Projecto9 TV 32'' LCD TV, Panasonic TX-32LX80

10 Computer Network3Com® Baseline Switch 282424 ports of 10/100/1000 connectivity / CISCO

11 B&W Printer OKI B4545 A4 MFP 12 WIFI CISCO 1231 Access Point13 Telephone Panasonic KX-T2375MXW14 PBX Panasonic PBX KXTDA100 – 16 Lines

15 Public Address SystemPublic Address System AHUJA India Amplifier 180 w, 6 x speakers, 2 x Mic (wired)

16 Whiteboards 1.8X1.2 meter17 Flip Charts18 Flip Charts Stand10 Text Books11 Training Manuals


160,000 USD


OFFICES2 Conference Room Table 04 Computer Table 85 Round Table 66 Instructor Desk 107 Cupboard - Short 88 Cupboard - Long 109 Roller Chair with arm rest 8

10 L-shape Manager Desk 111 Reception desk 112 Sofa 213 Side Table 814 Coffee Table 815 Dining Table 316 Armed Study Chair 6

Paper Punch 4 Hole 6Lamination Machine 1Binding Machine 1

CLASSROOMS1 Classroom Table 483 Classroom Chair 66

WORKSHOPS

Mech 87(included in bench 1 & Bench

2)

Heavy Duty Benches GPC HD Bench Inc. Record No 4 Vices & Pipe Vices

2 vices per bench and should come with 2 drawers 1 at each side 65

Bench 1Heavy Duty Benches ( 21 benche are needed for all workshops)

Wooden top blade 50 mm thick with steel angle iron sides. & bottom shelf approx. Dimensions : 0.9 x 2.5 x 01.2m (H x W x D) approximate. With 2 drawrers 1 at each side all sizes are approximate

32

OFFICES/CLASSROOMS/WORKSHOP EQUIPMENT


EQUIPMENT LIST

Appendix 6

Bench 2

Medium Duty Benches (19 Benches are needed for all workshopsand anonther 4 benches same specs but with rear panel)

Wooden top blade 25 mm thick with steel angle iron sides & bottom shelf. Dimensions : 0.9 x 2.5 x 01.2 m (H x W x D). With 2 drawrers 1 at each side (except the benches with rear panel - two draws on same side)all sizes are approximate

22

Vice 16'' vice (24 units needed for all workshops)

Heavy duty. Including removable jaws. Swil, anvil, large main screw.Quick release vice

3

Vice 24'' Vice (8 units to used in all workshops)

Heavy duty. Including removable jaws. Swil, anvil, large main screw.Quick release vice

6

Pipe Vice 1

can be used with up tp 3'' pipes. (3 units are needed to all workshops)

bench mounted and to be used with up to 3'' pipes 1

E&I 127 Steel

Cupboards

Steel Cupboards (5 units will be used in all workshops)

Medium duty steel cupboards with approximate dimensions of 1.2x0.5x2.0 (WxDxH)which will be used in workshops

1

Mech Compress

orAir Compressor Three Phase Small piston Compressor, 20cfm, 200L Recievr, 4HP Approx 1

E&I Air Dryer

Air Dryer (Matching with the E&I Compressor)

small desicant dryer Max pressure: 10 barRating: 220V, Single Phase, 50HzCFM : 90 (Matching with E&I compressor)

1

5Heavy-Duty Industrial Alloy Ladder (Class 1)

2

6Titan 5 Tread Heavy-Duty Industrial Alloy Platform Steps

2


4000 USD


Shelving Purpose fabricated shelving (30Kg max weight). Around wallsKey Cabinets

STORES EQUIPMENT




10,000 USD + 175 USD/Learner


SITE HSE REQUIREMENTSFirst Aid Kits 6

E&I LAB Emergency Eye Wash Station http://www.mynewlab.com/products/emergency_wash_stations.aspx 4

PPE/HSE EQUIPMENT FOR LEARNERS

OverallsFire retardant overalls - corporate colour for Learners. 30 XL, 30 L, 25M and 15S (Proportions)

200 200 per year. Different colour to instructors

Work BootsSteel toe capped, oil resistant soles, breathable. Suitable size range 7 to 11 UK size

200

Gloves Leather work gloves 200Safety goggles Normal and some to be worn over glasses 200

Hearing protectors Ear inserts 500Welding gloves Welding gloves (gauntlet type) 30

Hard hats 200 Different colour to instructors

PPE/HSE EQUIPMENT FOR INSTRUCTORS

OverallsFire retardant overalls - corporate colour for Instructors. With PETROFAC corporate logos.

30 200 per year. Different colour to Learners

Work BootsSteel toe capped, oil resistant soles, breathable. Suitable size range 7 to 11 UK size

30

Gloves Leather work gloves 30Safety goggles Normal and some prescription safety glasses to suit 30Welding gloves Welding gloves (gauntlet type) 10

Hard hats 50 Different colour to Learners

PPE/HSE EQUIPMENT FOR VISITORS/VIP's

Hard hats 50 Marked as Visitor

HSE ELEMENTS WITH COURSES

Fire Fighting Water Extinguisher 9ltr 10

HSE EQUIPMENT


EQUIPMENT LIST

Appendix 6

CO2 Extinguisher 10lb 10Foam Extinguisher 9ltr 10Fire Blanket 3Smoke Hoods 20

SCBA BA Sets 10Spare Cylinders 10Cleaning Facilities 1Recharge Facilities 1

First Aid CPR Mannequins 4Spine Model 1Eye Model 1Lifting Man Model 1Ear Model 1Defibrillator Laerdal Heartstart FR2 with ECG 1

NORM Radiation Meter Radex RAD01 1CSE Container 1

Gas Tester 1Torches 3Fall arrest block 15m 1Safety Harness 6Working Rope 20m 2Safety Lanyard 6Energy Absorber 6Tripod TM-8 1Man-Riding Winch 1

Working @ Height Scaffold Tower 1Safety Harness P-10R 10Safety Harness P-51E 1Energy Absorber ABM-T with AZ 002 at both ends 8Safety Lanyard LE 101 10 with AZ 022 8Safety Lanyard LB 102 10 10 with AZ 022 1Safety Lanyard LB 100 10 with AZ 043T Fall Arrest Block WR 200 06 with Swivel Snap Hook AZ 050 4Karabiners 40Safety Helmets Centurion 1125 40Working Rope 10m 20Safety Nets 2Work Positioning Device PROT 2 02 with AZ 051T 2Rope Grab AC 040Horizontal Lifelines AE 200 10m 1Rescue Lifting Sling AT 300 5Rescue Descent Device 20m AR 010 10Rescue Stretcher DX 017 4Webbing Sling 30cm AZ 900 10Tool Holder AY 002 40Duffle Bag AX 010 4Static Rope White LL140 1


4000 USD


Centre main entrance signCentre signage above reception deskcentre/corporate building paint to brand and tie in the training centre buildingsCentre promotional leaflets

Reception LCD/Plasma screen

Reception corporate video playing equipment

CORPORATE/BRANDING EQUIPMENT


EQUIPMENT LIST

Appendix 6


A product of Work Phase 2 and Translation


A product of Work Phase 2 and Translation

TRAINING MATERIALS


EQUIPMENT LIST

Appendix 6


40,000 USD


STATIONARY

A4 Paper 100 Boxes

A3 Paper 30 Boxes

A4 Plastic Sleeve Inserts 50 Boxes

A4 Ring Binder Files 4inch with Plastic Front Sleeve & 4 Rings

500 Piece

A4 Ring Binders 2inch with Plastic Front Sleeve and 4 Rings

500 Piece

Pens Black 300 Piece

Pens Blue 300 Piece

Pens Green 200 Piece

Pens Red 200 Piece

Pencils 500 Piece

Desktop Pencil Sharpener 20 Piece

Paper Clips 0.5 inch 20 boxStapler 20 Piece

Staples 50 boxErasers Plastic Type 100

Piece

Binding Spiral Clips A4 500 Piece

TRAINING CONSUMABLES


EQUIPMENT LIST

Appendix 6

Highlighter Markers 4 Color Sets

20 sets

A4 Lamination Sleeves 20 BoxA3 Lamination Sleeves 10 BoxWhite Board Marker Blue 400

Piece

White Board Marker Red 400 Piece

White Board Marker Green 400 Piece

White Board Marker Black 400 Piece

White Board Duster 20 Piece

Post It Note Paper 4 boxFlip Chat Stands 25 Piece

Flip Chart Paper Pads 75 Piece

Permanent Marker Black 100 Piece

Permanent Marker Blue 100 Piece

Permanent Marker Green 100 Piece

Permanent Marker Red 100 Piece

Wall Clock 15 Piece

Note Book Hard Back A4 100 Piece

Note Book Hard Back A5 100 Piece

Calendars 15 Piece

Calculators 25 Piece

Desk Organizers 10 Piece

Scissors 4 inch 20 Piece

Envelopes Brown A4 200 Piece

Envelopes Brown Letter 200 Piece

WORKSHOP MATERIALS

PIPEWORKSteel pipe 1/2 NB Schedule 40 50mSteel pipe 3/4 NB Schedule 40 100mSteel pipe 1 NB Schedule 40 100mSteel pipe 1 1/2 NB Schedule 40 100mSteel pipe 2 NB Schedule 40 100mSteel pipe 1 NB Schedule 80 100mSteel pipe 3 NB Schedule 40 50mSteel pipe 4 NB Schedule 40 50mPipe fittings Weld flange - 1" Table D 200Pipe fittings Weld flange - 2" Table D 200Pipe fittings Weld flange - 3" Table D 200Pipe fittings Weld flange - 4" Table D 200Pipe fittings Long radius bend - 1" NB Sched 40 100Pipe fittings Long radius bend - 2" NB Sched 40 100Pipe fittings Long radius bend - 3" NB Sched 40 100Pipe fittings Long radius bend - 4" NB Sched 40 100Sealing material PTFE Tape 300 rollsSealing material Hemp 100 rollsSealing material Sealing paste - Boss White 60 tubs


WELDING

Welding Electrodes 2.5mm dia. 2.1kg

•2.5mm diameter•2.1kg (approx 140) 30 10 USD

Welding Electrodes 2.0mm dia. 2kg 30 10 USDWelding Electrodes 2.5mm dia. 2.1kg 30 10 USD0.9mm Flux Cored Wire 4.5kg 10 60 USD0.6mm Welding Wire 5kg 15 20 USDArgon Gas 15 20 USDAluminium Welding Wire 0.8mm 0.3kg 3 20 USDRed Welding Gloves 7 USD

additional equipment detail to be added.

ELECTRICAL/INSTRUMENTATION

Detail to follow

Date post:	26-Jun-2015
Category:	Documents
Upload:	sidou
View:	168 times
Download:	4 times

Appendix

Documents