• DIN Radio Provision with Pocket• ISO Mount Radio Provision with Pocket• Double DIN Radio Provision• Stacked ISO Mount Units Provision• Painted to Match Factory
• A) Radio Housing • B) ISO Brackets • C) Trim Plate • D) Double DIN Brackets • E) Double DIN Trim Plate • F) Snap in Pocket
Refer also to the instructions included with the aftermarket radio.
KNOWLEDGE IS POWEREnhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry.Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow.
Metra recommends MECPcertified technicians
1
3
MITSUBISHI LANCER 2008-UP
99-7011 DASH DISASSEMBLY
Disconnect the negative battery ter-minal to prevent an accidental shortcircuit.
1
Open the glove box and remove (1)Phillips screw from the panel to theright of the glove box door. Unclipand remove the panel. (Figure A)
Remove (1) Phillips screw from thepanel above the glove box thenunclip and remove the panel. (Figure B)
Continued on page 2.
2
B
A
2
MITSUBISHI LANCER 2008-UP
99-7011 DASH DISASSEMBLY
4 Unclip the radio switch panel includ-ing the hazard switch assembly.Unplug hazard switch assembly andremove panel. (Figure C)
5 Remove (4) Phillips screws secur-ing the radio chassis. Unplug andremove chassis.
7 Unclip assembly, unplug ribboncable from assembly and removeassembly from the factory radiopanel. Retain screws and hazardswitch assembly for re-use duringkit preparation.
6 Remove (3) Phillips screws securingthe hazard switch assembly to thefactory radio switch panel. Unclipand remove the switch. (Figure D)
8 Unclip and remove the a/c ventsfrom the factory radio switch panel.(Retain a/c vents for re-use duringkit preparation)
9 Remove and retain (7) factory clipsfrom rear of radio housing for re-use during kit preparation.
Continue to kit preparation.
PASSENGERAIRBAG OFF PASSENGER
PASSENGERAIRBAG OFF PASSENGER
D
C
3
99-7011 KIT PREPARATION
Secure the hazard switch assembly into the radio housing using the factory hard-ware. Snap the a/c vents into the radio housing. (Figure A)
Use the (7) plastic factory clips previously removed during dash disassembly andattach where shown. (Figure B)
1
2
PASSENGER
PASSENGER
AIRBAG OFF
A
REAR VIEW OF RADIO HOUSING
B
MITSUBISHI LANCER 2008-UP
Continue to kit assembly
99-7011 KIT ASSEMBLY
4
A
B
C
DIN RADIO PROVISION WITH POCKET
Slide the DIN cage into the RadioHousing and secure by bending themetal locking tabs outward. (Figure A)
1
Slide the aftermarket radio into thecage until it snaps into place. (Figure B)
2
Snap the pocket into the radio hous-ing. (Figure C)
3
Continue to final assembly.
*Note: Refer also to the instructions included with the aftermarket radio.
99-7011 KIT ASSEMBLY
5
A
B
C
ISO MOUNT RADIO PROVISION WITH POCKET
Mount the ISO Brackets to the radiousing the screws supplied with theradio. (Figure A)
1
Slide the radio into the radio housinguntil it snaps into place. (Figure B)
2
Snap the trim plate onto the front ofthe radio housing. (Figure B)
3
Snap the Pocket into the radio housing.(Figure C)
4
Continue to final assembly.
*Note: Refer also to the instructions included with the aftermarket radio.
99-7011 KIT ASSEMBLY
6
DOUBLE DIN RADIO PROVISIONSTACKED ISO MOUNT UNITS PROVISION
Cut and remove the center bar fromthe radio housing. (Figure A)
1
Snap the Double DIN brackets to theinside edge of the radio housing.(Figure B)
2
Slide the Double DIN or stacked ISOmount unit(s) into the bracket/radiohousing assembly and secure theunit(s) to the assembly using thescrews supplied with the unit(s).(Figure C)
3
Continue to final assembly.
*Note: Refer also to the instructions included with the aftermarket radio.
A
B
C
Snap the Double DIN trim plate ontothe front of the radio housing. (Figure C)
4
99-7011 FINAL ASSEMBLY
FINAL ASSEMBLY
(A) Strip wire ends back 1/2"
B) Twist ends together
C) Solder
D) Tape
A
B
C
D
Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individ-ually tape off the ends of any unused wires to prevent electrical short circuit.)
Re-connect the negative battery terminal and test the unit for proper operation.
Reassemble radio and dash assemblies in reverse order of disassembly.
1
2
3
FINAL WIRING CONNECTIONS
Make wiring connections using the EIA color code chart shown below and the instructions included with thehead unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and
individually tape off ends of any unused wires to prevent electrical short circuit.
METRA / EIA WIRING CODE12V Ignition / Acc . . . . . . . . . . Red
12V Batt / Memory. . . . . . . . . Yellow
Ground. . . . . . . . . . . . . . . . . . Black*
Power Antenna. . . . . . . . . . . . Blue
Amp Turn-On . . . . . . . . . . . . . Blue / White
Amp Ground. . . . . . . . . . . . . . Black / White
Right Front (-). . . . . . . . . . . . . Gray/ Black
Left Front (+) . . . . . . . . . . . . . White
Left Front (-). . . . . . . . . . . . . . White / Black
Right Rear (+) . . . . . . . . . . . . Violet
Right Rear (-) . . . . . . . . . . . . . Violet / Black
Left Rear (+) . . . . . . . . . . . . . Green
Left Rear (-) . . . . . . . . . . . . . . Green / Black
*NOTE: When a Black wire is not present, ground radio to vehicle chassis. All colors may not be present on all leads due to manufacturer’s specifications.
