Aprilaire Communicating Thermostat System Installation Manual

Fractionation Tray and HardwareProduct Bulletin 400

Superior performance by design™Raschig GmbH - Jaeger Products, Inc

Product Bulletin-400Page 1

TABLE OF CONTENTS

Raschig Jaeger Technologies 2

Services 4

Comparison of Various Packed Column Internals 3

Valve Types 5

Tray Selection/Materials of Construction 6

Conventional Fractionation Trays 7Valve TraysSieve TraysBubble Cap Trays

Specialty Trays 9Dualflow TraysSide-to-Side Baffle TraysDisc & Donut Trays

Special Design Features 10

Valve Units 11

Assembly Part Numbers 12-18

High Capacity Trays 8NYE TraysEC TechnologyCoFlo Trays Trays


Raschig Jaeger Technologies – September 2006

In order to establish a new alliance in mass transfer business RASCHIG GmbH and its parent companyPMC GLOBAL INC have acquired JAEGER PRODUCTS INC., a Houston Texas based company, which isa major manufacturer of tower packings, column internals and speciality trays and very active in the MassTransfer and Environmental Business.

RASCHIG JAEGER will be integrated into the PMC network of highly specialized, internationally operatingcompanies and will therefore be better prepared to meet increased globalization and further improvedcustomer orientation. Wherever in the world – in all continents – RASCHIG JAEGER is on the spot.

Synergies

This strategic acquisition combining RASCHIG and JAEGER into one larger group gives a great advantageto our customers giving them access to products of both entities in Europe, The Americas and in other partsof the world. It will create new dimensions in mass transfer technology. The advantages of our processengineering know-how and our technologies benefit even more the planning, modernization andconstruction of our clients’ processes. And: saving energy and investment cost is part of it.

The new alliance offers a diverse array of products to meet the mass transfer needs of the industries. Whilespecializing in high performance products, the comprehensive products line of RASCHIG JAEGER alsoincludes traditional fractional trays as well as structured and random packing types that best fit theapplication.

Leading In-house distributor test-facility

The company operates one of the largest in-house distributor test-facilities worldwide. Liquid distributorscan be tested up to 12m in diameter at a maximum liquid load of 2400m3 per hour.

All products of RASCHIG JAEGER are the result of consistent development work long years of experience.Comprehensive quality management in all stages of production and the principle of offering completesolutions are the basis of our excellent reputation – worldwide.


Comparison of Various Packed Column Internals

In the last few years our industry has consolidated through varies acquisitions and mergers. Because ofthese business activities part numbers for varies items have become difficult to follow. In an effort helpeveryone with this conversion the chart below is provided. The information for Raschig and Jaeger is veryaccurate; however, because of some unique design characteristics some part numbers could be interpretedusing slightly different numbers.

The information provided for the other vendors is our best effort to convert there system to “fit” ournumbering system; again this information is subject to some interpretation due to constantly changingdesigns.

At best this information should be used as a starting point or a guide. Do to the nature of the informationwe cannot guarantee its accuracy.

Internals Raschig Jaeger Sulzer CT Old Norpro Koch-Glitsch-Norpro

Liquid Distributor /Redistributor

DR 2 LD1, CR1 VSL, VSI, VSH 106, 845, 107 301A, 301B, 906

DR 3 LD5, CR5 798 301A, 301B, 905

DT 1 LD4 VEG, VKG 126, 1016 126, 320, 926

DT 1 (1) LD4 (1) VKR 136 136, 321, 986

DT 2 (2) LD4 (2) MTS, VEL, VEP 806 310, 302, 806, 985DT 2 (1) LD4 (2) MTS, VEL, VEP 126, 1016, 127, 1017

RP 2 LD1, CR1 116, 816, 117, 817 301A & D, 916, 917

RP 2 (1) LD2, CR2 116, 1006, 117, 851, 1007 301B & D, 116, 117

DP 1 LD3, LD7 VRG 844, 141 304, 330, 342, 941DP-S LD6 VRD 1044 344, 305, 1044, 943

DT-S LD4 (1) VEL, VEP 136, 137 312, 312SDT-MF LD-MF VKRPW 996

Feed Pipe DP-P FP1 VR, LV 119, 129, 719, 729 340, 119, 719Gas GV 1 GD3 GIO, GIG 196, 198 342, 746Distributor GV 2 GDS Vane Type GIV 194 351, 768

GV 3 GD2 SK 896 716

Flash Device FB 1 FP1 (3) 655 300, 745

FB 2 855 705

FB 3 LRR, LRP 755 341, 755

FB 3/RP 2 898 300

Bed Limiter - Random HP 1 BL1 RPB 103, 823 401- Random HP 2 BL1 402

- Structured HP-P BL2 HE, HS 133 403Support Plate - Random SP 1 PS1 GIS 804, 819, 1019 101R, 804

- Random SP 2, SP 3 PS1 EMS 809, 818 101, 103, 814, 824- Structured SP-P PS2 TEB, TSB 134 102, 802

SP-HG 104

SP 1/ RP 2 201A, 201B

Liquid CV 1 CT3, CRS SLR 633 510, 511Collector CP 1 CT1 SK 733 501

CP 2 CT2 SK 833 501

Liq-Liq extraction DSP 1 834 600

(internals not in RaschigHB)

DSP 2 835 600

DP-P 644, 744

(1) Drip tubes in troughs

(2) Notches with drip tubes

(3) Flash Device


Services

Raschig Jaeger specializes in the design and manufactureof mass transfer equipment for the Chemical ProcessIndustries (CPI). Our primary tray products includeconventional sieve, valve, and bubble cap trays; packedinternals such as liquid distributors, chimney trays, packingsupport plates, and holddowns; and multiple styles of randomand structural packing.

Raschig Jaeger also offers specialty trays such as highcapacity trays, high uplift strength trays, dual flow, disc & donut,and sideto-side baffle trays.

Our products are backed by decades of experience andemployees committed to quality, excellence, and service.Raschig Jaeger, a member of FRI (Fractionation ResearchInstitute) has a staff fully capable of providing completehydraulic and mechanical design of any new equipmentrequired to suit all your needs. Process designs are madebased on proven concepts. Our computerized mechanicalengineering and fabricated systems are integrated to permitefficient and accurate processing of orders.

Raschig Jaeger focuses on effective design, responsiveservice, and efficient manufacturing. Whether small diameter orlarge, new construction, revamp or replacement, we willprovide reliable solutions to our customer’s requirements at aneconomical price.

To compliment Raschig Jaeger’sproduct line of tray internals, we alsosupply replacement parts andinstallation hardware. Raschig Jaeger’shardware response group is dedicatedto our customer’s immediate and futurerequirements for replacement hardware.Our inventory is maintained and staffedby experienced personnel dedicated toquality, service and customer

satisfaction.

Product Bulletin-400Page 5Quality Tray Products

Tray Selection

Tray type selection is generally accomplished by balancing various process and mechanicalconsiderations. Major mechanical and process factors taken into consideration include capacity,efficiency, turndown, pressure drop, susceptibility to corrosion and fouling, and actual experience in thesystem.

What may be an overriding consideration in one case may be unimportant in another; therefore,each situation must be examined on its own merits. With the exception of special licensed traytechnologies, Raschig Jaeger has the capability to produce virtually any type of conventional or specialtytray type

GENERAL TRAY CLASSIFICATION

Materials of ConstructionRaschig Jaeger trays can be fabricated from numerous types of materials. In addition to working

with the most common carbon, ferritic, and austenitic steels, we also work with many exotic materialssuch as Hastelloy® alloys, titanium and specialty duplex stainless steels. A brief listing of acceptable

materials of construction include:

carbon steel 321 stainless steel Inconel®410S stainless steel 347 stainless steel nickel304L stainless steel 904L stainless steel titanium316L stainless steel Hastelloy® alloy 2205317L stainless steel Monel® alloy 2

LowHighMediumHighUltra HighCoFlo

LowMediumMediumVery HighVery HighEC Technology

MediumMediumMediumHighHighNYE

Very HighVery LowMediumVery LowHighDisc & Donut

Very HighVery LowMediumVery LowHighBaffle

HighLowVery LowMediumHighDual Flow

LowHighVery HighVery HighLowBubble Cap

HighLowMediumVery HighMediumFixed Valve

LowMediumMediumVery HighHighHigh Capacity Valve

LowMediumHighVery HighMediumMoving Valve

MediumLowLowVery HighMediumSieve

Fouling ResistancePressure DropTurndownEfficiencyCapacityTray Type

Product Bulletin-400Page 6Valve Types

Valve Variations: leg length, anti-spin tabs, flush seating, alternate weightsFixed Valve Variations: net rise (curtain area)

RJ-V0

Round Fixed Valve

RJ-SVG

Rectangular Fixed Valve

RJ-MV

High Capacity Fixed Mini Valve

RJ-MMV

High Capacity Mini Valve

RJ-A6

RJ-A3 with Venturi Orifice

RJ-A3

2-Piece Caged Valve

RJ-A5


RJ-A2

2-Piece Caged Valve

RJ-A4


RJ-A1

3-Piece High Turndown Caged Valve

RJ-V4

RJ-V1 with Venturi Orifice

RJ-V1

1-Piece Moving Valve

Raschig Jaeger offers a vast array of conventional and HighCapacity moving and fixed valve types to meet all of ourcustomer’s needs. The single piece RJ-V1 is our standardmoving valve and is recommended for many applications. TheRJ-V1 incorporates tabs to raise the main body of the valve off ofthe tray floor thereby reducing the chance of sticking. RaschigJaeger manufactures many types of 1 piece, 2 piece cage anddisc (RJ-A2 or RJ-A3), and 3 piece high turndown (RJ-A1) valveunits with thickness, material type, and leg lengths as needed tomeet any process and mechanical conditions required. Additionalvariations include extruded tray floor openings to reducepressure drop and multiple valve weights to permit uniformoperation over a wider operating range. See section -- for acomplete listing and description of our most common styles

Sieve trays began to dominate the CPI’s mass and heattransfer applications in the 1950’s. Prior to that, bubble cap trayswere the industry’s workhorse. The sieve tray is a flat perforatedplate. If extreme turndown conditions are not required, sieve trayswill likely meet your process performance objective. Additionally,sieve trays have better anti-fouling characteristics and lowerpressure drop when compared to standard moveable valve trays.Raschig Jaeger has the capability to provide virtually any type ofsieve tray. Perforation sizes as small as 1/8” in diameter areoffered

Sieve Trays

Product Bulletin-400Page 7Conventional Fractionation Trays

Valve Trays

Raschig Jaeger designs and provides numerous variationsof bubble cap trays. Our most common designs includeconventional slotted caps and the standard FRI solid cap (noslots). Standard cap sizes are 3”, 4”, and 6”. Of course, customdesigns are available as well. Typical manufacturing methods tosecure the riser and cap assembly to the tray floor includeextrusion and press fitting, seal welding, and pull-through boltingconnections.

Bubble cap trays usually have a lower capacity (10-20percent) than properly designed valve or sieve trays; however, theyare capable of efficient performance over a wider operating rangedue to their superior leak proof characteristics.

Although some bubble cap tray towers have beenretrofitted with the more modern three piece RJ-A1 valve unit,bubble caps still enjoy wide-spread industrial application insystems where low liquid rates and large variations in vaporloadings are present

Bubble Cap Trays

Product Bulletin-400Page 8High Capacity Trays

NYE TRAYS®

Raschig Jaeger recommends high capacity NYE TRAYS when conventional trays fall short. Theyhave been successfully used in hundreds of installations since the 1980’s and incorporate advancedtechnology to increase the capacity of columns by 10 to 30% over conventional trays. NYE TRAYSachieve these improvements by use of a special inlet area design that reduces tray pressure drop andincreases the available area for vapor/liquid contacting. NYE TRAYS are a good general purpose highcapacity tray as they are well suited for a wide variety of mass and heat transfer services. Most revampscan be accomplished with little or no welding to the vessel. NYE TRAYS are also well adapted to upsetprone services where upgraded mechanical strength is required.

Trays equipped with EC (entrainment capture) Technology can achieve capacity increases up to50% over conventional fractionation tray designs. The maximum benefit is realized for trays that arelimited by entrainment flooding mechanisms. However, downcomer limited systems can also bedebottlenecked because less area needs to be allocated for liquid/vapor contacting on the deck. ECTechnology can be integrated with any tray deck contacting device (valve, fixed valve, sieve, bubblecap) and is compatible with any flow pass configuration. Trays with EC Technology have equal or betterseparation efficiency compared to conventional trays due to enhanced vapor/liquid contacting within theentrainment capture zone .

The CoFloTM Tray is a Ultra High Capacity gas-liquid contacting device. Performance testsdemonstrate 100+% capacity increases over conventional fractionation trays while maintaining excellentcontact efficiencies. Each tray consists of three components: a liquid disperser, the contacting zone, andthe liquid/vapor separator. High capacities are achieved due to cocurrent flow of liquid and vapor phasesthrough the contacting zone. CoFlo trays are ideally suited for debottlenecking where an existing towercan be used in lieu of replacement with a larger diameter. Tray components are modular and selfsupporting and in most cases can be fitted onto existing support rings and downcomer bars. Cartridgeconstruction is recommended for column diameters < 30in (762mm).

EC Technology

CoFlo Trays


Side-to-side baffle trays and disc & donut traysare arranged in a tower in such a manner that the liquidand vapor contacting is accomplished by vapor passingthrough a curtain of liquid falling from one tray to thenext or through rivulets of liquid flowing throughperforations in the tray deck. Tray decks are flat orslightly inclined plates that occupy 40-60 percent of thetower area. Designs which incorporate perforateddecks are typically 40 percent open so that there issufficient overlap between adjacent rows of plates.

For a given tray spacing, both types of trayshave a higher capacity and lower pressure drop thanconventional sieve or valve trays or even dualflowtrays; however, their liquid/vapor contacting efficiencyis significantly lower. Baffle trays and disc & donut traysare particularly well suited to heavy fouling systemsdue to their extremely high open area. Typicalapplications include heavy oil refining andpetrochemical heat transfer services having a highsolid and/or petroleum coke content. Raschig Jaegercan provide any of these specialty trays withmechanically robust features to improve resistance todislodging

Dualflow trays are sieve trays that do not havedowncomers. The entire active or bubbling area isperforated with holes with typical hole sizes rangingfrom 1/2” - 1” in diameter. Vapor and liquid counter-currently flow through the perforations; hence, thename Dualflow. Under normal operating conditions,liquid splashes about on top of the tray in a wave-likemanner. Liquid flows downward momentarily throughperforations in the areas of wave crests whereasvapor flows upward through perforations in the areabetween crests.

High open area dualflow trays have a highercapacity and lower pressure drop compared toconventional fractionation trays at the same trayspacing and are particularly well suited to systemscontaining a moderate to high level of solids or wherepolymerizable compounds are present. The maindisadvantage of dualflow trays is their narrow efficientoperating range. The majority of industrial applicationsare more common in small to moderate towerdiameters. However, large diameter designs have alsobeen employed. Levelness is especially important withdual-flow trays. Trays which are not level potentiallysuffer from gross liquid and vapor flow partitioningthrough the deck

Specialty Trays

Dualflow Trays

Baffle and Disc & Donut Trays

Product Bulletin-400Page 10Special Design Features

Raschig Jaeger offers a full complement of modern tray features to permit an optimized solution toalmost any tray design challenge. Process and/or mechanical considerations dictate when special featuresare required. Our experienced process design team understands these requirements so that our

customer’s needs are realized

Downcomer DesignsIn addition to the standard chordal / segmental design, Raschig Jaeger also offers multichordal,

circular, and envelope styles

Anti-Jump BafflesAnti-jump baffles are used on 2, 3 and 4 pass trays. Their purpose is to prevent the liquid which is

flowing across the tray from jumping over the downcomer onto the opposing flow path. This conditionprimarily occurs when the width of the center or off-center downcomer is small and the tray loading is high

Picket Fence WeirsPicket-fence weirs are devices used to artificially increase the effective liquid height on the bubbling

area and reduce blowing. They are commonly used when the liquid flow over the weir < 1 gpm/in (8.94m3/hr m). Alternately, the picket fence weir is used on multipass trays to achieve hydraulic balancebetween the passes. The picket-fence weir is constructed of either a continuous metal plate havingrectangular notches or by attaching individual baffles to the weir at a uniform spacing

Recessed Inlet PansRecessed inlet pans are used in conjunction with sloped downcomers to reduce the head loss under

the downcomer. Sloped downcomers with recessed inlet pans are primarily used in heavy liquid loadedservices prone to downcomer backup flooding.

Swept-Back WeirsSwept-back weirs are used on side downcomers to reduce the effective liquid height on the tray by

lowering the volumetric liquid flow rate per unit length of outlet weir. They can also be used in multipasstray design to balance weir loads between the side and off-center or side and center downcomers of 3 and4 pass trays, respectively.

Splash BafflesSplash baffles are devices utilized in very low liquid rate services as either an alternative or

complement to picket-fence weirs. Splash baffles consist of a metal plate oriented vertically and parallel tothe overflow weir having a 1/2” - 1” setback away from the weir above the tray deck. The purpose of thesplash baffle is to maximize the liquid retention time on the tray

For Valve Styles not listed, contact Jaeger Products for availability.

T410, T304L, T316L

T410, T304L, T316L

T410, T304L, T316L

T410, T304L, T316L

T410, T304L, T316L

T410, T304L, T316LT410, T304L, T316LT410, T304L, T316LT410, T304L, T316LT410, T304L, T316LT410, T304L, T316LT410, T304L, T316LT410, T304L, T316LT410, T304L, T316LT410, T304L, T316LT410, T304L, T316LT410, T304L, T316LT410, T304L, T316LT410, T304L, T316LT410, T304L, T316L

T410, T304L, T316L

T410, T304L, T316L

T410, T304L, T316L

T410, T304L, T316L

T410, T304L, T316L

T410, T304L, T316L

RJ-A1, Assembly 2116 Valve Plate, 16 Ga.

RJ-A1, Assembly 3220 Orifice Cover, 20 Ga.

RJ-V1, 1716 Valve, 16 Ga.

RJ-V1, 1714 Valve, 14 Ga.

RJ-A1, Assembly 1116 Travel Stop, 16 Ga.



RJ-A1, Assembly 3218 Orifice Cover, 18 Ga.




RJ-A2, Assembly 1214 Travel Stop, 14 Ga.RJ-A3,RJ-A3,RJ-A4,RJ-A4,RJ-A5,RJ-A5,RJ-A6,RJ-A6,RJ-V4,RJ-V4,RJ-MMV,RJ-MV,RJ-SVG,RJ-V0


Valve Units

The installation hardware, replacement valves, and conventional fractionation trays shown in thisbrochure represent the typical tray design used in the industry. Other existing hardware styles may differ

in appearance from those depicted in the booklet; however the application is generally the same

DESCRIPTION STOCK MATERIAL

1A-1 Valve Assembly Travel Stop

Valve Plate Orifice Cover

Valve Plate

1A-2 Valve AssemblyTravel Stop

2V-1 Valve

Hex Nut

Product Bulletin-400Page 12INSTALLATION HARDWARE

DESCRIPTION

3/8" -16 UNC Thread

1/2" -13 UNC Thread

5/8" -11 UNC Thread

3/4" -10 UNC Thread

3/8"X 1" LG -16 UNC Thread

3/8"X 1-1/2" LG -16 UNC Thread













STOCK MATERIAL

Other specific material types of hardware available upon request

C. S., T410SS, T304L, T316L

C. S., T410SS, T304L, T316L

C. S., T410SS, T304L, T316L

C. S., T410SS, T304L, T316L

C. S., T410SS, T304L, T316L

C. S., T410SS, T304L, T316L

C. S., T410SS, T304L, T316L

C. S., T410SS, T304L, T316L

C. S., T410SS, T304L, T316L

C. S., T410SS, T304L, T316L

C. S., T410SS, T304L, T316L

C. S., T410SS, T304L, T316L

C. S., T410SS, T304L, T316L

C. S., T410SS, T304L, T316L

C. S., T410SS, T304L, T316L

C. S., T410SS, T304L, T316L

C. S., T410SS, T304L, T316L

C. S., T410SS, T304L, T316L

Hex Bolt

STOCK MATERIALDESCRIPTION

Dog Point Bolts

Split Lock Washers





C. S. T410SS, T304L, T316L

C. S. T410SS, T304L, T316L

C. S. T410SS, T304L, T316L

T410, T304L, T316L

Carbon Steel

C. S., T410, T304L, T316L

C. S., T410, T304L, T316L

14 Ga., 7/16" ID x 1" OD for 3/8" Bolts


12 Ga., 9/16" ID x 1-1/2" OD for 1/2" Bolts


T410, T304L, T316L

Carbon Steel



3/8" ID , Split Lock Washer

1/2" ID , Split Lock Washer

C. S. T304, T316

C. S. T304, T316










1/4 "T., 7/16" ID x 1-3/4" OD for 3/8" Bolts

1/4 "T., 9/16" ID x 2" OD for 1/2" Bolts

1/4 "T., 11/16" ID x 2" OD for 5/8" Bolts

T410, T304L, T316L

T410, T304L, T316L

T410, T304L, T316L

C. S. T410, T304L, T316L

C. S. T410, T304L, T316L

C. S. T410, T304L, T316L

C. S. T410, T304L, T316L

C. S. T410, T304L, T316L

C. S. T410, T304L, T316L

C. S. T410, T304L, T316L

C. S. T410, T304L, T316L

C. S. T410, T304L, T316L


Tray Washers

Domed Washers

Frictional Washers


RJ-12 Seal Plate, 12 Ga. 3" Long

RJ-12A Seal Plate, 12 Ga. 3-1/2" Long

RJ-12B Seal Plate, 12 Ga. 4" Long

RJ-12C Seal Plate, 12 Ga. 4-1/2" Long

RJ-12D Seal Plate, 12 Ga. 5" Long

RJ-12X Seal Plate, 12 Ga. Variable Length

RJ-10 Seal Plate, 10 Ga. 3" Long

RJ-10A Seal Plate, 10 Ga. 3-1/2" Long

RJ-10B Seal Plate, 10 Ga. 4" Long

RJ-10C Seal Plate, 10 Ga. 4-1/2" Long

RJ-10D Seal Plate, 10 Ga. 5" Long

RJ-10X Seal Plate, 10 Ga. Variable Length

RJ-10 Angle Hanger, 10 Ga. 5" Long

RJ-20 Angle Hanger, 10 Ga. 6" Long

RJ-30 Angle Hanger, 10 Ga. Length Variable

RJ-8 Clip Angle, 14 Ga.



RJ-45 Lock Clamp 12 Ga., for 3/8”Shaved Stud

RJ-45A Lock Clamp 10 Ga., for 3/8“Shaved Stud

RJ-40A Lock Clamp 3/16" Lip 12 Ga.,for 3/8" Shaved Stud

RJ-40B Lock Clamp 1/4" Lip 12 Ga.,for 3/8" Shaved Stud

RJ-40C Lock Clamp 5/16" Lip 12 Ga.,for 3/8" Shaved Stud

RJ-40D Lock Clamp 3/8" Lip 12 Ga.,for 3/8" Shaved Stud

RJ-40E Lock Clamp 1/2" Lip 12 Ga.,for 3/8" Shaved Stud

RJ-40F Lock Clamp 5/8" Lip 12 Ga.,for 3/8" Shaved Stud

RJ-40G Lock Clamp 3/4" Lip 12 Ga.,for 3/8" Shaved Stud

RJ-40H Lock Clamp 7/8" Lip 12 Ga.,for 3/8" Shaved Stud

RJ-40X Lock Clamp 1" Lip 12 Ga.,for 3/8" Shaved Stud

T410, T304L, T316L

T410, T304L, T316L

T410, T304L, T316L

T410, T304L, T316L

T410, T304L, T316L

T410, T304L, T316L

C. S T410, T304L, T316L

C. S T410, T304L, T316L

C. S T410, T304L, T316L

C. S T410, T304L, T316L

C. S T410, T304L, T316L

C. S T410, T304L, T316L

C. S T410, T304L, T316L

C. S T410, T304L, T316L

C. S T410, T304L, T316L

T410, T304L, T316L

C. S T410, T304L, T316L

C. S T410, T304L, T316L

C. S T410, T304L, T316L

C. S T410, T304L, T316L

C. S T410, T304L, T316L

C. S T410, T304L, T316L

C. S T410, T304L, T316L

C. S T410, T304L, T316L

C. S T410, T304L, T316L

C. S T410, T304L, T316L

C. S T410, T304L, T316L

C. S T410, T304L, T316L

C. S T410, T304L, T316L

STOCK MATERIALDESCRIPTION

Seal Plates

Angle Hangers

Clip Angles

Manway Lock Clamps

Manway Lock Clamps

Product Bulletin-400Page 15DESCRIPTION

RJ-3 Lock Clamp 3/16" T.,for 3/8" Shaved Stud

RJ-3A Lock Clamp Stud 1/4” T.,for 3/8" Shaved Stud

RJ-2 Lock Clamp 3/16" T.,for 3/8" Shaved Stud

RJ-2A Lock Clamp 1/4” T.,for 3/8" Shaved Stud

RJ-5 Manway Stud 3/8"- 16 UNC x 2" LGShaved Stud

RJ-7 Manway Stud 3/8"- 16 UNC x 2-1/2" LGShaved Stud

RJ-8 Manway Stud 1/2"- 13 UNC x 2-1/2" LGShaved Stud

RJ-9 Manway Stud 1/2"- 13 UNC x 3" LGShaved Stud

LJ-50 Bottom Clamp 12 Ga., for 3/8" Bolt

LJ-50A Bottom Clamp 10 Ga., for 3/8" Bolt

RJ-51 Bottom Clamp 12 Ga.,with 3/8"-16UNC Nut

RJ-51A Bottom Clamp 10 Ga.,with 3/8"-16UNC NutNut welded in place on top side of clamp

STOCK MATERIAL

C. S T410, T304L, T316L

C.S.

C. S T410, T304L, T316L

C.S.

C. S T410, T304L, T316L

C. S T410, T304L, T316L

C. S T410, T304L, T316L

C. S T410, T304L, T316L

T410, T304L, T316L

C. S T410, T304L, T316L

T410, T304L, T316L

C. S T410, T304L, T316L


Manway Lock Clamps

Manway Lock Clamps

Manway Studs

Bottom Tray Clamps

Bottom Tray Clamps



DESCRIPTION

RJ-52 Bottom Clamp 12 Ga.,w / 3/8" x 3" -16 UNC Bolt

RJ-52A Bottom Clamp 10 Ga.,w / 3/8" x 3" -16 UNC Bolt

RJ-52S Bottom Clamp 12 Ga.,w / 3/8" x 3" -16 UNC Bolt

RJ-52SX Bottom Clamp 10 Ga.,w / 3/8" x 3" -16 UNC Bolt

RJ-52Z Bottom Clamp 12 Ga.,w / 3/8" x 3" -16 UNC Bolt

RJ-52ZX Bottom Clamp 10 Ga.,w / 3/8" x 3" -16 UNC Bolt

RJ-20A-H Bottom Clamp 12 Ga.,3/16" to 7/8" Lip

RJ-20J-P Bottom Clamp 12 Ga.,1" to 1-3/4" Lip

RJ-22A-H Bottom Clamp 12 Ga.,3/16" to 7/8" LipWith 3/8"-16 UNC welded nut

RJ-22J-P Bottom Clamp 12 Ga.,1" to 1-3/4" LipWith 3/8"-16 UNC welded nut

RJ-23A-H Bottom Clamp 12 Ga.,3/16" to 7/8" LipWith 3/8"x 1-1/2" thru 2"-16 UNC welded bolt

RJ-23J-P Bottom Clamp 12 Ga.,1" to 1-3/4" LipWith 3/8"x 1-1/2" thru 3"-16 UNC welded bolt

RJ-H1, 3/8"-16UNC x 9.347" Lg.RJ-H2, 3/8"-16UNC x 6.750" Lg.

STOCK MATERIAL

T410, T304L, T316L

C. S T410, T304L, T316L

T410, T304L, T316L

C. S T410, T304L, T316L

T410, T304L, T316L

C. S T410, T304L, T316L

T410, T304L, T316L

T410, T304L, T316L

T410, T304L, T316L

T410, T304L, T316L

T410, T304L, T316L

T410, T304L, T316L

C. S., T304, T316C. S., T304, T316

Bottom Tray Clamp

Bottom Tray Clamp

Bottom Tray Clamp

Hook Bolts

All sizes available in either Drop Warp or Non-Drop Warp:Exception is 1” Wide, available in Non-Drop Warp only.

DESCRIPTION

RJ-GW1, 1/16" x 3/8" ID. x 1" OD

RJ-GW2, 1/16" x 3/8" ID. x 1-1/2" OD

RJ-GW3, 1/16" x 3/8" ID. x 1-3/4" OD

RJ-GW4, 1/16" x 3/8" ID. x 2" OD

RJ-GW5, 1/16" x 3/8" ID. x 2-1/2" OD

RJ-GW6, 1/8" x 3/8" ID. x 1" OD

RJ-GW7, 1/8" x 3/8" ID. x 1-1/2" OD

RJ-GW8, 1/8" x 3/8" ID. x 1-3/4" OD

RJ-GW9, 1/8" x 3/8" ID. x 2" OD

RJ-GW10, 1/8" x 3/8" ID. x 2-1/2" OD

RJ-TG1, 1/16" x 1" wide (NDW)

RJ-TG2, 1/16" x 1-1/4" wide

RJ-TG3, 1/16" x 1-1/2" wide

RJ-TG4, 1/16" x 2" wide

RJ-TG5, 1/16" x 2-1/2" wide

RJ-TG6, 1/16" x 3" wide

RJ-TG7, 1/8" x 1" wide (NDW)

RJ-TG8, 1/8" x 1-1/4" wide

RJ-TG9, 1/8" x 1-1/2" wide

RJ-TG10, 1/8" x 2" wide

RJ-TG11, 1/8" x 2-1/2" wide

RJ-TG12, 1/8" x 3" wide


Washer Gaskets

Tape Gaskets

STOCK MATERIAL

D-8080, Teflon, NeopreneTN9000, Greenguard










Fiberglass, Teflon, NeopreneCeramic Fiber












RJ-RSG1, 1/8" x 1/8" Square






RJ-RSG7, 1" x 1“ Square

RJ-RSG8, 1-1/8" x 1-1/8" Square

RJ-RSG9, 1-1/4" x 1-1/4" Square

RJ-RSG10, 1-1/2" x 1-1/2" Square

RJ-RRG1, 1/8" Round

RJ-RRG2, 1/4" Round

RJ-RRG3, 3/8" Round

RJ-RRG4, 1/2" Round

RJ-RRG5, 5/8" Round

RJ-RRG6, 3/4" Round

RJ-RRG7, 1" Round

RJ-RRG8, 1-1/8" Round



DESCRIPTIONProduct Bulletin-400

Page 18

Rope Gaskets

STOCK MATERIAL

Fiberglass, Teflon, NeopreneCeramic Fiber, Gortex





















100 General Product Information

200 Metal Random - RSR

300 Mist Eliminators – Wire Mesh

400 Fractionation Trays and Hardware

450 High Capacity – Nye Trays

475 High Capacity – CoFlo Trays

500 Metal Structured Packing – RSR

525 Metal Structured Packing - MaxPak

550 Plastic Structured Packing – RSP

RASCHIG JAEGER TECHNOLOGIESMundenheimer Strasse 10067061 Ludwigshafen - GermanyPhone: +49.62.5618-602 ∙ Fax: +49.621.5618-604email: [email protected] www.raschig.com

Jaeger Products, Inc.1611 Peachleaf StreetHouston, TX 77039Phone: 281.449.9500 ∙ Fax: 281.449.9400800.678.0345 www.jaeger.com

Locations / Production Sites

Ludwigshafen and Espenhain,Germany

Houston, TexasEl Dorado, KansasAnd Monterrey, Mexico.

Furthermore we co-operate with reliable partners all over the world

600 Plastic Random – Jaeger Tri-Pack/Hackentten

625 Plastic Random – RSR

650 Plastic Random – LPR

675 Plastic Random – Nor Pak

700 Plastic Random – Rings and Saddles

800 Ceramic Random Packing

900 Winsorp Software

1000 Process Information

1100 Column Internals

1200 Reactor Internals

Date post:	09-Feb-2022
Category:	Documents
Upload:	others
View:	9 times
Download:	0 times

Aprilaire Communicating Thermostat System Installation Manual

Documents