Date post: | 12-Jan-2017 |
Category: |
Engineering |
Upload: | siva-nagendra-reddy |
View: | 139 times |
Download: | 1 times |
BYP.SIVA NAGENDRA REDDY
ASSISTANT PROFESSORDEPARTMENT OF ECE
KUPPAM ENGINEERING COLLEGEMail id:[email protected]
BYP.SIVA NAGENDRA REDDY
ASSISTANT PROFESSORDEPARTMENT OF ECE
KUPPAM ENGINEERING COLLEGEMail id:[email protected]
1Siva Nagendra Reddy,ECE ,Assistant Professor
PROCEDURE TO SIMULATEARDUINO USING PROTEUS
PROCEDURE TO SIMULATEARDUINO USING PROTEUS
2Siva Nagendra Reddy,ECE ,Assistant Professor
Install Arduino IDE First make sure that you have Proteus installed in your
operating system. If not, then download and installProteus. After run the Proteus software, If you don't find
Arduino in the library.
First make sure that you have Proteus installed in youroperating system. If not, then download and installProteus. After run the Proteus software, If you don't find
Arduino in the library.
3Siva Nagendra Reddy,ECE ,Assistant Professor
Procedure:Step 1: Download the ARDUINO Library Files from website. Open downloaded zip Folder Copy ARDUINO.LIB and ARDUINO.IDX files. Paste ARDUINO.LIB and ARDUINO.IDX files in to
Proteus Library folder. C drive>Program Files>Labcenter Electronics>Proteus 7
Professional>LIBRARYStep 2: Now open Proteus and Search Arduino.Step 3: Make Hex file.Step 4: Upload Code and run.
Step 1: Download the ARDUINO Library Files from website. Open downloaded zip Folder Copy ARDUINO.LIB and ARDUINO.IDX files. Paste ARDUINO.LIB and ARDUINO.IDX files in to
Proteus Library folder. C drive>Program Files>Labcenter Electronics>Proteus 7
Professional>LIBRARYStep 2: Now open Proteus and Search Arduino.Step 3: Make Hex file.Step 4: Upload Code and run.
4Siva Nagendra Reddy,ECE ,Assistant Professor
Step 1 Download the ARDUINO Library Files from website. Open downloaded zip Folder Copy ARDUINO.LIB and ARDUINO.IDX files. Paste ARDUINO.LIB and ARDUINO.IDX files in to
Proteus Library folder. C drive>Program Files>Labcenter Electronics>Proteus
7 Professional>LIBRARY
Download the ARDUINO Library Files from website. Open downloaded zip Folder Copy ARDUINO.LIB and ARDUINO.IDX files. Paste ARDUINO.LIB and ARDUINO.IDX files in to
Proteus Library folder. C drive>Program Files>Labcenter Electronics>Proteus
7 Professional>LIBRARY
5Siva Nagendra Reddy,ECE ,Assistant Professor
Step 3:
Make .hex FileOpen Arduino SoftwareBefore start simulation need to make sure that in
File>>Preferences, compilation is marked. Because"compilation" compile the code and generate .hex file.This .hex file is needed for running the Proteus
simulation.
Make .hex FileOpen Arduino SoftwareBefore start simulation need to make sure that in
File>>Preferences, compilation is marked. Because"compilation" compile the code and generate .hex file.This .hex file is needed for running the Proteus
simulation.
9Siva Nagendra Reddy,ECE ,Assistant Professor
After writing your code, click on compile then you willget the Link of Your Hex file at the Output go to thatplace and get your Hex file.Then copy(Ctrl+C) the .hex file.
After writing your code, click on compile then you willget the Link of Your Hex file at the Output go to thatplace and get your Hex file.Then copy(Ctrl+C) the .hex file.
12Siva Nagendra Reddy,ECE ,Assistant Professor
Step 4
Upload code and run. Run the Proteus and draw the circuit like the picture.You can directly connect Led with pin 13.But it is a
good practice to add a 220 ohm resistor with led inseries. Resistor limits the current flow.Right click on Arduino and Paste the .hex file in
"Program File”.Run the simulation by clicking "Run the simulation"
button.LED is Blinking if everything is okay.
Upload code and run. Run the Proteus and draw the circuit like the picture.You can directly connect Led with pin 13.But it is a
good practice to add a 220 ohm resistor with led inseries. Resistor limits the current flow.Right click on Arduino and Paste the .hex file in
"Program File”.Run the simulation by clicking "Run the simulation"
button.LED is Blinking if everything is okay.
13Siva Nagendra Reddy,ECE ,Assistant Professor