Supporting Information for
Regulating Immobilization Performance of Metal-organic
Coordination Polymers through Pre-coordination for Biosensing
Hua Yang,a Xin Qi,c Xinquan Wang,a Xiangyun Wang,a Qiang Wang,a Peipei Qi,a
Zhiwei Wang,a Xiahong Xu,a Yingchun Fub,c and Shouzhuo Yaoc
a State Key Lab Breeding Base for Zhejiang Sustainable Plant Pest Control; Institute of Quality and Standard for
Agro-products, Zhejiang Academy of Agricultural Sciences; Hangzhou 310021, Chinab College of Biosystems Engineering and Food Science, Zhejiang University, Hangzhou 310058, China
c Key Laboratory of Chemical Biology and Traditional Chinese Medicine Research (Ministry of Education of
China), College of Chemistry and Chemical Engineering, Hunan Normal University, Changsha 410081, China.
* Corresponding author: Fax: +86 571 8641834; Tel: +86 571 86415202E-mail address: [email protected]* Corresponding author: Fax: +86 571 88982530; Tel: +86 571 88982534; E-mail address: [email protected]
Fig. S1. UV-vis spectra and the absorbance intensities at 320 nm (the insert) of 0.5 mg mL-1 DMcT suspension after the additions of different concentrations of CuCl2.
Wavelength /nm300 350 400 450
Absorbance 0.0
.5
1.0
1.5
2.0
0.1 mM0.2 mM0.3 mM0.4 mM0.5 mM0.6 mM0.7 mM
CCu2+ /mM
0.0 .2 .4 .6
Absorbance
1.0
1.2
1.4
1.6
cCuCl2 / mM
0.0 .2 .4 .6 .8 1.0 1.2 1.4 1.6 1.8
j /
A c
m-2
40
50
60
70
80
90
100
Fig. S2. Response currents of biosensors prepared in different concentrations of CuCl2
to 1 mM glucose in pH 7.0 PBS at 0.7 V vs. SCE.
Potential /V0.0 .2 .4 .6 .8
i / A
-10
0
10
20
30
40
PBSPBS with 1mM H2O2
Potential /V0.0 .2 .4 .6 .8
i / A
-10
0
10
20
30
40
Potential /V0.0 .2 .4 .6 .8
i / A
-10
0
10
20
30
40
Potential /V0.0 .2 .4 .6 .8
i / A
-10
0
10
20
30
40
PBSPBS with 1mM H2O2
PBSPBS with 1mM H2O2
PBSPBS with 1mM H2O2
A B
C D
Fig. S3. CV curves to the addition of 1 mM H2O2 obtained in PBS (pH 7.0) for MOCPsCu (A), MOCPsAu (B), MOCPsCu+Au (C), bare Au (D) modified Au electrode.
Fig. S4. Ratios of the responses of biosensor to the initial ones during the storage in PBS at 4 oC.
t / day0 10 20 30 40 50
i/i0 %
0
20
40
60
80
100
Fig. S5. Potentiostatic responses of the biosensor to 1 mM glucose, 0.1 mM ascorbic acid (AA) and 0.1 mM uric acid (UA) at 0.7 V vs SCE in PBS.
t / s0 30 60 90 120 150
i / A
0
2
4
6
8
glucose AA UA
glucose
Table S1. Comparisons of detection potential and performance of glucose oxidase-based biosensors. LDR: linear detection range; LOD: limit of detection.
TitleSensitivity/A mM-1
cm-2
LDR /mMLOD /M
Ref.
Genetically Engineered Phage-Templated MnO2 Nanowires:
Synthesis and Their Application in Electrochemical Glucose Biosensor Operated at Neutral pH Condition
141 0.005-2 1.8 Ref.[1]
MOCPsCu+Au/Au 127 1-3555 0.058 This work
Direct Electron Transfer of Enzymes in a Biologically Assembled Conductive
Nanomesh Enzyme Platform107 0.05-1 10 Ref.[2]
Nitrogen-doped carbon foam as an efficient enzymatic biosensing platform for glucose sensing
98.46 0.00051-19 0.17 Ref.[3]
Fabrication of a third-generation glucose biosensor using graphene-
polyethyleneimine-gold nanoparticles hybrid
93 0.001-0.1 0.32 Ref.[4]
Self-assembled NiFe2O4/carbon nanotubes sponge for enhanced glucose biosensing application
84.10-3.0, 3.2-
12.498 Ref.[5]
MOCPsAu/Au 84 1-1555 0.075 This work
MOCPsCu/Au 59 10-1550 0.194 This work
Plain to point network reduced graphene oxide - activated carbon
composites decorated with platinum nanoparticles for urine glucose
detection
61.06 0.002-10 2 Ref.[6]
Thin-film amperometric multibiosensor for simultaneous
determination of lactate and glucose in wine
58.4 0.005-0.8 5 Ref.[7]
New CNT/poly(brilliant green) and CNT/poly(3,4-
ethylenedioxythiophene) based electrochemical enzyme biosensors
57 0.013-1.5 13 Ref.[8]
A highly sensitive and stable glucose biosensor using thymine-based
polycations into laponite hydrogel films
52.8 0.1-1.6 40 Ref.[9]
A new strategy for achieving vertically-erected and hierarchical
TiO2 nanosheets array/carbon cloth as a binder-free electrode for protein
impregnation, direct electrochemistry and mediator-free glucose sensing
52 Up to 1.2 23.4 Ref.[10]
Electrografting of thionine diazonium cation onto the graphene edges and
decorating with Au nano-dendrites or glucose oxidase: Characterization and
electrocatalytic applications
43.2 0.5-6.0 9.6 Ref.[11]
A glucose biosensor based on the polymerization of aniline induced by a bio-interphase of glucose oxidase and
horseradish peroxidase
41.87 0.0165-10 5.4 Ref.[12]
One-Pot Hydrothermal Synthesis of Magnetite Prussian Blue Nano-
Composites and Their Application to Fabricate Glucose Biosensor
32 0.005-1.2 0.5 Ref.[13]
Nitrogen-Doped Carbon Nanotubes Supported by Macroporous Carbon as
an Efficient Enzymatic Biosensing Platform for Glucose
29.4 0.0058-18 1.93 Ref.[14]
Flexible 3D nitrogen-doped carbon nanotubes nanostructure: A good
matrix for enzyme immobilization and biosensing
24.8 0.1-12.5 6 Ref.[15]
One-step solvothermal preparation of silver-ZnO hybrid nanorods for use in enzymatic and direct electron-transfer
based biosensing of glucose
18.70.01-0.1, 0.1-1.5
5 Ref.[16]
Construction of titanium dioxide nanorod/graphite microfiber hybrid electrodes for a high performance electrochemical glucose biosensor
18.6 / 2.2 Ref.[17]
Chitosan supported silver nanowires as a platform for direct electrochemistry and highly sensitive electrochemical
glucose biosensing
16.72 1-15 2.1 Ref.[18]
Evaluation of the Oxo-bridged Dinuclear Ruthenium Ammine
Complex as Redox Mediator in an Electrochemical Biosensor
12.3 0.0252-0.1 9.63 Ref.[19]
Synthesis and characterization of microparticles based on poly-
methacrylic acid with glucose oxidase for biosensor applications
11.98 0.009-8.26 10 Ref.[20]
Biosensing of glucose in flow injection analysis system based on glucose
oxidase-quantum dot modified pencil graphite electrode
11.5 0.01-1.0 3 Ref.[21]
Ferrocene-functionalized graphene electrode for biosensing applications
9.369 0.03-0.6 20 Ref.[22]
Integration of microfluidic injection analysis with carbon
nanomaterials/gold nanowire arrays-based biosensors for glucose detection
8.59 0.05-4.0 / Ref.[23]
Mechanism of amperometric biosensor with electronic-type-controlled carbon
nanotube5.6 0.025-1.4 37 Ref.[24]
Rational Design of Bioelectrochemically Multifunctional
Film with Oxidase, Ferrocene, and Graphene Oxide for Development of in
Vivo Electrochemical Biosensors
4.3 0.05-0.5 10 Ref.[25]
Increased sensitivity of extracellular glucose monitoring based on AuNP
decorated GO nanocomposites3.9 0.3-20 300 Ref.[26]
An amperometric glucose biosensor based on a MnO2/graphene composite
modified electrode3.3 0.04-2 10 Ref.[27]
Graphene oxide–mediated electrochemistry of glucose oxidase on
glassy carbon electrodes3.1 Up to 0.6 20 Ref.[28]
Paper-based enzymatic reactors for batch injection analysis of glucose on
3D printed cell coupled with amperometric detection
2.55 1-10 110 Ref.[29]
Direct electrochemistry of glucose oxidase immobilized on Au
nanoparticles-functionalized 3D hierarchically ZnO nanostructures and its application to bioelectrochemical
glucose sensor
1.409 1-20 20 Ref.[30]
Carbon nanotubes non-covalently functionalized with cytochrome c: A
new bioanalytical platform for building bienzymatic biosensors
1.37 0.1-1 8 Ref.[31]
Electrocatalytic (Bio)Nanostructures Based on Polymer-Grafted Platinum Nanoparticles for Analytical Purpose
0.25 / / Ref.[32]
References[1] L. Han, C.X. Shao, B. Liang, A.H. Liu, Genetically Engineered Phage-Templated MnO2
Nanowires: Synthesis and Their Application in Electrochemical Glucose Biosensor Operated at Neutral pH Condition, ACS Applied Materials & Interfaces, 8 (2016) 13768-13776.
[2] S.W. Lee, K.Y. Lee, Y.W. Song, W.K. Choi, J. Chang, H. Yi, Direct Electron Transfer of Enzymes in a Biologically Assembled Conductive Nanomesh Enzyme Platform, Advanced Materials, 28 (2016) 1577-1584.
[3] Y.G. Song, D. Su, Y. Shen, C.C. Gong, Y.H. Song, L. Wang, Nitrogen-doped carbon foam as an efficient enzymatic biosensing platform for glucose sensing, Analytical Methods, 8 (2016) 4547-4553.
[4] P. Rafighi, M. Tavahodi, B. Haghighi, Fabrication of a third-generation glucose biosensor using graphene-polyethyleneimine-gold nanoparticles hybrid, Sensors and Actuators B-Chemical, 232 (2016) 454-461.
[5] Y.C. Li, M.G. Zhao, J. Chen, S.S. Fan, J.J. Liang, L.J. Ding, S.G. Chen, Self-assembled NiFe2O4/carbon nanotubes sponge for enhanced glucose biosensing application, Applied Surface Science, 362 (2016) 115-120.
[6] M.F. Hossain, J.Y. Park, Plain to point network reduced graphene oxide - activated carbon composites decorated with platinum nanoparticles for urine glucose detection, Scientific Reports, 6 (2016).
[7] L.V. Shkotova, N.Y. Piechniakova, O.L. Kukla, S.V. Dzyadevych, Thin-film amperometric multibiosensor for simultaneous determination of lactate and glucose in wine, Food Chemistry, 197 (2016) 972-978.
[8] M.M. Barsan, V. Pifferi, L. Falciola, C.M.A. Brett, New CNT/poly(brilliant green) and CNT/poly(3,4-ethylenedioxythiophene) based electrochemical enzyme biosensors, Analytica Chimica Acta, 927 (2016) 35-45.
[9] V.I.P. Zanini, M. Gavilan, B.A.L. de Mishima, D.M. Martino, C.D. Borsarelli, A highly sensitive and stable glucose biosensor using thymine-based polycations into laponite hydrogel films, Talanta, 150 (2016) 646-654.
[10] J. Liu, Z.M. He, S.Y. Khoo, T.T.Y. Tan, A new strategy for achieving vertically-erected and hierarchical TiO2 nanosheets array/carbon cloth as a binder-free electrode for protein impregnation, direct electrochemistry and mediator-free glucose sensing, Biosensors & Bioelectronics, 77 (2016) 942-949.
[11] R.K. Shervedani, A. Amini, N. Sadeghi, Electrografting of thionine diazonium cation onto the graphene edges and decorating with Au nano-dendrites or glucose oxidase: Characterization and electrocatalytic applications, Biosensors & Bioelectronics, 77 (2016) 478-485.
[12] C.C. Gong, J.Y. Chen, Y.H. Song, M. Sun, Y.G. Song, Q.H. Guo, L. Wang, A glucose biosensor based on the polymerization of aniline induced by a bio-interphase of glucose oxidase and horseradish peroxidase, Analytical Methods, 8 (2016) 1513-1519.
[13] E.Y. Jomma, S.N. Ding, One-Pot Hydrothermal Synthesis of Magnetite Prussian Blue Nano-Composites and Their Application to Fabricate Glucose Biosensor, Sensors, 16 (2016).
[14] Y.H. Song, X.P. Lu, Y. Li, Q.H. Guo, S.L. Chen, L.Q. Mao, H.Q. Hou, L. Wang, Nitrogen-Doped Carbon Nanotubes Supported by Macroporous Carbon as an Efficient Enzymatic Biosensing Platform for Glucose, Analytical Chemistry, 88 (2016) 1371-1377.
[15] M. Zhang, G.Y. Zhou, Y. Feng, T.R. Xiong, H.Q. Hou, Q.H. Guo, Flexible 3D nitrogen-doped carbon nanotubes nanostructure: A good matrix for enzyme immobilization and biosensing, Sensors and Actuators B-Chemical, 222 (2016) 829-838.
[16] J. Li, M.M. Lu, Z.N. Tan, Y.B. Xu, Y.C. Zhang, X.Y. Hu, Z.J. Yang, One-step solvothermal preparation of silver-ZnO hybrid nanorods for use in enzymatic and direct electron-transfer based biosensing of glucose, Microchimica Acta, 183 (2016) 1705-1712.
[17] J. Zhang, X. Yu, W.B. Guo, J.C. Qiu, X.N. Mou, A.X. Li, H. Liu, Construction of titanium dioxide nanorod/graphite microfiber hybrid electrodes for a high performance electrochemical glucose biosensor, Nanoscale, 8 (2016) 9382-9389.
[18] S. Kumar-Krishnan, S. Chakaravarthy, A. Hernandez-Rangel, E. Prokhorov, G. Luna-Barcenas, R. Esparza, M. Meyyappan, Chitosan supported silver nanowires as a platform for direct electrochemistry and highly sensitive electrochemical glucose biosensing, RSC Advances, 6 (2016) 20102-20108.
[19] P.A. Raymundo-Pereira, A.C.V. Mascarenhas, M.F.S. Teixeira, Evaluation of the Oxo-bridged Dinuclear Ruthenium Ammine Complex as Redox Mediator in an Electrochemical Biosensor, Electroanalysis, 28 (2016) 562-569.
[20] J.P.H. Perez, B. Lopez-Ruiz, E. Lopez-Cabarcos, Synthesis and characterization of microparticles based on poly-methacrylic acid with glucose oxidase for biosensor applications, Talanta, 149 (2016) 310-318.
[21] O. Saglam, B. Kizilkaya, H. Uysal, Y. Dilgin, Biosensing of glucose in flow injection analysis system based on glucose oxidase-quantum dot modified pencil graphite electrode, Talanta, 147 (2016) 315-321.
[22] A. Rabti, C.C. Mayorga-Martinez, L. Baptista-Pires, N. Raouafi, A. Merkoci, Ferrocene-functionalized graphene electrode for biosensing applications, Analytica Chimica Acta, 926 (2016) 28-35.
[23] Y.Q. Qin, J.W. Cui, Y. Zhang, Y. Wang, X.Y. Zhang, H.M. Zheng, X. Shu, B.W. Fu, Y.C. Wu, Integration of microfluidic injection analysis with carbon nanomaterials/gold nanowire arrays-based biosensors for glucose detection, Science Bulletin, 61 (2016) 473-480.
[24] H. Hidaka, K. Nowaki, H. Muguruma, Mechanism of amperometric biosensor with electronic-type-controlled carbon nanotube, Japanese Journal of Applied Physics, 55 (2016).
[25] X.Y. Wang, Q. Li, J.J. Xu, S. Wu, T.F. Xiao, J. Hao, P. Yu, L.Q. Mao, Rational Design of Bioelectrochemically Multifunctional Film with Oxidase, Ferrocene, and Graphene Oxide for Development of in Vivo Electrochemical Biosensors, Analytical Chemistry, 88 (2016) 5885-5891.
[26] M. Qi, Y. Zhang, C.M. Cao, Y. Lu, G.Z. Liu, Increased sensitivity of extracellular glucose monitoring based on AuNP decorated GO nanocomposites, RSC Advances, 6 (2016) 39180-39187.
[27] Y.G. Liu, X.M. Zhang, D.N. He, F.Y. Ma, Q. Fua, Y. Hu, An amperometric glucose biosensor based on a MnO2/graphene composite modified electrode, RSC Advances, 6 (2016) 18654-18661.
[28] S. Castrignano, F. Valetti, G. Gilardi, S.J. Sadeghi, Graphene oxide-mediated electrochemistry of glucose oxidase on glassy carbon electrodes, Biotechnology and Applied Biochemistry, 63 (2016) 157-162.
[29] A.A. Dias, T.M.G. Cardoso, R.M. Cardoso, L.C. Duarte, R.A.A. Munoz, E.M. Richter, W.K.T. Coltro, Paper-based enzymatic reactors for batch injection analysis of glucose on 3D printed cell coupled with amperometric detection, Sensors and Actuators B-Chemical, 226 (2016) 196-203.
[30] L.X. Fang, B. Liu, L.L. Liu, Y.H. Li, K.J. Huang, Q.Y. Zhang, Direct electrochemistry of glucose oxidase immobilized on Au nanoparticles-functionalized 3D hierarchically ZnO nanostructures and its application to bioelectrochemical glucose sensor, Sensors and Actuators B-Chemical, 222 (2016) 1096-1102.
[31] M. Eguilaz, C.J. Venegas, A. Gutierrez, G.A. Rivas, S. Bollo, Carbon nanotubes non-covalently functionalized with cytochrome c: A new bioanalytical platform for building bienzymatic biosensors, Microchemical Journal, 128 (2016) 161-165.
[32] F. Gal, L. Challier, F. Cousin, H. Perez, V. Noel, G. Carrot, Electrocatalytic (Bio)Nanostructures Based on Polymer-Grafted Platinum Nanoparticles for Analytical Purpose, ACS Applied Materials & Interfaces, 8 (2016) 14747-14755.