+ All Categories
Home > Documents > ArvoTec Feeder and spreader manual - Fish Tech · ArvoTec Feeder and spreader manual ... 1 HOW TO...

ArvoTec Feeder and spreader manual - Fish Tech · ArvoTec Feeder and spreader manual ... 1 HOW TO...

Date post: 21-Jul-2018
Category:
Upload: hadieu
View: 235 times
Download: 0 times
Share this document with a friend
16
ArvoTec Feeder and spreader manual Ruukintie 45, 79620 Huutokoski FINLAND tel: +358- 207 - 299910 fax: +358- 207 - 299911 [email protected] www.arvotec.fi Arvo-Tec Updated 1.8.2007
Transcript

ArvoTec page 1 Automation for modern aquaculture

Ruukintie 45, 79620 Huutokoski, FINLAND tel: +358-17-5559900 fax: -5559950 [email protected] www.arvotec.fi

ArvoTec Feeder and spreader manual

Ruukintie 45, 79620 Huutokoski FINLAND tel: +358- 207 - 299910 fax: +358- 207 - 299911 [email protected] www.arvotec.fi

Arvo-Tec

Updated 1.8.2007


ArvoTec page 2 Automation for modern aquaculture

Ruukintie 45, 79620 Huutokoski, FINLAND tel: +358-17-5559900 fax: -5559950 [email protected] www.arvotec.fi

Table of content DO NOT… IMPORTANT!

1 HOW TO CALIBRATE ARVO-TEC FEEDERS................................................................................................. 3

2 TD 2000 DOSING UNIT (CODE 1010) PARTS AND CODES ........................................................................... 4

3 HOW TO INSTALL SPRINGS TO ARVO-TEC FEEDERS & PNEUMATIC SPREADER.......................... 5

4 HOW TO INSTALL PNEUMATIC SPREADER TO ARVO-TEC FEEDERS ................................................ 6

4.1 PNEUMATIC SPREADER INSTALLATION DETAILS VER 2007, CODE 1081 ............................................................... 6 4.2 SPREADER INSTALLATION IN 4 PHASES ................................................................................................................ 7 4.3 SPREADER WIRING WITHOUT CABLE CONNECTORS .............................................................................................. 8 4.4 OPTIONAL PNEUMATIC SPREADER DOSE DIVIDER CODE 1079 .............................................................................. 8 4.5 PNEUMATIC SPREADER VER 2000 (CODE 1080) WITH PART CODES ...................................................................... 9 4.6 PNEUMATIC SPREADER VER 2007 (CODE 1081) WITH PART CODES ...................................................................... 9

5 ELECTRICAL SPREADER ................................................................................................................................. 10

5.1 ELECTRIC SPREADER ASSEMBLY........................................................................................................................ 11

6 TEORETHICAL ARVO-TEC FEEDER DOSING CAPACITY WITH DIFFERENT DRUM AND MOTOR OPTIONS........................................................................................................................................................ 12

7 BRACKETS, HANGERS AND STANDS ............................................................................................................ 13

7.1 BRACKET ASSEMBLY T- DRUM GRANULATE HOPPER HANGER BAIL CODE 1048................................................ 13 7.2 TD 2000 HINGED HANGER CODE 1050 ............................................................................................................... 14 7.3 TD 2000 SIMPLE HANDER CODE 1049................................................................................................................ 15 7.4 TD 2000 50-150 L HOPPER HANGER CODE 1054. 150 L HOPPER IN THE PICTURE................................................ 16

THE INFORMATION CONTAINED HERE IN IS PROPRIETARY TO ARVO-TEC AND IS NOT TO BE REPRODUCED OR USED WITHOUT THE EXPRESS WRITTEN PERMISSION OF ARVO-TEC

DO NOT! -anything else than fish feed to the feed silos and dosing units -do not put your fingers, hands to the dosing unit when power is on -do not stand closer than 1 m from the feeder or do not look to feeder or spreader opening when power is on -system is automatic and can start without warning -always take power off before doing any service -if you are not sure what to do please contact manufacturer or your local distributor


ArvoTec page 3 Automation for modern aquaculture

Ruukintie 45, 79620 Huutokoski, FINLAND tel: +358-17-5559900 fax: -5559950 [email protected] www.arvotec.fi

1 How to calibrate Arvo-Tec feeders The find out the feeding speed (=feeder calibration value) you can run, for example a 100 second test and weigh all the feed that comes out. Feeding speed is the feed amount in g / 100 s. It is very important that this is exactly correct for Control System. Normally (=using standard trout and salmon feeds) all Arvo-Tec feeders are equal (with the same type of the dosing drum) but the feeding speed depends on the feed type (size, pellet shape and ingredients). To run the test use the following procedure: -Put feed into the feeder -Run the feeder so that the feed start to come out -Run 100 s test and take all feed -Weigh the feed -Feeding speed = feed amount g / 100 s


ArvoTec page 4 Automation for modern aquaculture

Ruukintie 45, 79620 Huutokoski, FINLAND tel: +358-17-5559900 fax: -5559950 [email protected] www.arvotec.fi

2 TD 2000 dosing unit (code 1010) parts and codes


ArvoTec page 5 Automation for modern aquaculture

Ruukintie 45, 79620 Huutokoski, FINLAND tel: +358-17-5559900 fax: -5559950 [email protected] www.arvotec.fi

3 How to install springs to Arvo-Tec Feeders & Pneumatic spreader If you have feeder XLR connectors supplied with the feeders, connect 24 VAC to 1 and 0 to 2, leave 3 free.

Springs are supplied and used only with 5 g drums or smaller

Spreader with Bolt M3 x 10 mm Nut M3 Nyloc

Feeder with spring. (Without spreader!) Screw 2,9 x 13 mm


ArvoTec page 6 Automation for modern aquaculture

Ruukintie 45, 79620 Huutokoski, FINLAND tel: +358-17-5559900 fax: -5559950 [email protected] www.arvotec.fi

4 How to install Pneumatic spreader to Arvo-Tec Feeders

4.1 Pneumatic Spreader installation details ver 2007, code 1081

Screw 2,9 x 13 mm

Spreader TD 2000 CA 1.5 l with junction box

Power 24 VACin

Pressure

Power to feeder 0,6-

Pressure to spreader 0,6-5m

Pressure max. 10 bar in


ArvoTec page 7 Automation for modern aquaculture

Ruukintie 45, 79620 Huutokoski, FINLAND tel: +358-17-5559900 fax: -5559950 [email protected] www.arvotec.fi

4.2 Spreader installation in 4 phases

1 2

3

Spreader ver 2000 connections

4

Power in Pin 1 = +24 VAC Pin 2 = 0 VAC

Quick connector Pipe outer diamater 8 mm. Norm. pressure 2- 4, max. 10 bar.


ArvoTec page 8 Automation for modern aquaculture

Ruukintie 45, 79620 Huutokoski, FINLAND tel: +358-17-5559900 fax: -5559950 [email protected] www.arvotec.fi

4.3 Spreader wiring without cable connectors

4.4 Optional Pneumatic spreader dose divider code 1079

+24 VAC ( brown )0 VAC ( blue )

SPREADER

FEEDER


ArvoTec page 9 Automation for modern aquaculture

Ruukintie 45, 79620 Huutokoski, FINLAND tel: +358-17-5559900 fax: -5559950 [email protected] www.arvotec.fi

4.5 Pneumatic spreader ver 2000 (code 1080) with part codes

4.6 Pneumatic spreader ver 2007 (code 1081) with part codes

113051

113052

1121

112001 112004

112003 1124 1122

1123 1125

113051

113052

1121

112001

112004 112041

1124 1122

1125

1122

1123


ArvoTec page 10 Automation for modern aquaculture

Ruukintie 45, 79620 Huutokoski, FINLAND tel: +358-17-5559900 fax: -5559950 [email protected] www.arvotec.fi

5 Electrical spreader Speed adjustment head.

Adustable sector blockers Feeding Robot with spreader Spreader and Control Unit in outdoor round tank


ArvoTec page 11 Automation for modern aquaculture

Ruukintie 45, 79620 Huutokoski, FINLAND tel: +358-17-5559900 fax: -5559950 [email protected] www.arvotec.fi

5.1 Electric spreader assembly


ArvoTec page 12 Automation for modern aquaculture

Ruukintie 45, 79620 Huutokoski, FINLAND tel: +358-17-5559900 fax: -5559950 [email protected] www.arvotec.fi

6 Teorethical Arvo-Tec feeder dosing capacity with different drum and motor options

Calibrate feeders (see chapter 1) to detect the actual feeding speed of the feeders!

Arvo-Tec technical document

Dosing capacity with different drum and motor options

Updated 25.4.2002 Maximum theoretical dosing capacity Normal feeding capacity Note! Actual capacity is feed dependent

Cup size Cups max. Dosing capacity if motor Dosing capacity if motor = / feed runs all the time rest 50% of the time

Minimum Drum size Motor options Motor options Dose mm

G 1 2 5 15 1 2 5 15 rpm rpm rpm rpm rpm rpm rpm rpm unit unit

0,3 24 1 0,12 0,24 0,60 1,80 g/s 0,06 0,12 0,30 0,90 g/s 7,20 14,40 36,00 108,00 g/min 3,60 7,20 18,00 54,00 g/min 0,43 0,86 2,16 6,48 kg/h 0,22 0,43 1,08 3,24 kg/h 6,91 13,82 34,56 103,68 kg/16h 3,46 6,91 17,28 51,84 kg/16h1 24 2 0,40 0,80 2,00 6,00 g/s 0,20 0,40 1,00 3,00 g/s 24,00 48,00 120,00 360,00 g/min 12,00 24,00 60,00 180,00 g/min 1,44 2,88 7,20 21,60 kg/h 0,72 1,44 3,60 10,80 kg/h 23,04 46,08 115,20 345,60 kg/16h 11,52 23,04 57,60 172,80 kg/16h5 12 4 1,00 2,00 5,00 15,00 g/s 0,50 1,00 2,50 7,50 g/s 60,00 120,00 300,00 900,00 g/min 30,00 60,00 150,00 450,00 g/min 3,60 7,20 18,00 54,00 kg/h 1,80 3,60 9,00 27,00 kg/h 57,60 115,20 288,00 864,00 kg/16h 28,80 57,60 144,00 432,00 kg/16h

20 8 6 2,67 5,33 13,33 40,00 g/s 1,33 2,67 6,67 20,00 g/s 160,00 320,00 800,00 2400,00 g/min 80,00 160,00 400,00 1200,00 g/min 9,60 19,20 48,00 144,00 kg/h 4,80 9,60 24,00 72,00 kg/h 153,60 307,20 768,00 2304,00 kg/16h 76,80 153,60 384,00 1152,00 kg/16h

45 4 8 3,00 6,00 15,00 45,00 g/s 1,50 3,00 7,50 22,50 g/s 180,00 360,00 900,00 2700,00 g/min 90,00 180,00 450,00 1350,00 g/min 10,80 21,60 54,00 162,00 kg/h 5,40 10,80 27,00 81,00 kg/h 172,80 345,60 864,00 2592,00 kg/16h 86,40 172,80 432,00 1296,00 kg/16h

100 4 9 6,67 13,33 33,33 100,00 g/s 3,33 6,67 16,67 50,00 g/s 400,00 800,00 2000,00 6000,00 g/min 200,00 400,00 1000,00 3000,00 g/min 24,00 48,00 120,00 360,00 kg/h 12,00 24,00 60,00 180,00 kg/h 384,00 768,00 1920,00 5760,00 kg/16h 192,00 384,00 960,00 2880,00 kg/16h


ArvoTec page 13 Automation for modern aquaculture

Ruukintie 45, 79620 Huutokoski, FINLAND tel: +358-17-5559900 fax: -5559950 [email protected] www.arvotec.fi

7 Brackets, hangers and stands

7.1 Bracket assembly T- Drum Granulate hopper hanger bail code 1048.

Plastic rivet ∅3x8 4 pcs.


ArvoTec page 14 Automation for modern aquaculture

Ruukintie 45, 79620 Huutokoski, FINLAND tel: +358-17-5559900 fax: -5559950 [email protected] www.arvotec.fi

7.2 TD 2000 hinged hanger code 1050


ArvoTec page 15 Automation for modern aquaculture

Ruukintie 45, 79620 Huutokoski, FINLAND tel: +358-17-5559900 fax: -5559950 [email protected] www.arvotec.fi

7.3 TD 2000 simple hander code 1049


ArvoTec page 16 Automation for modern aquaculture

Ruukintie 45, 79620 Huutokoski, FINLAND tel: +358-17-5559900 fax: -5559950 [email protected] www.arvotec.fi

7.4 TD 2000 50-150 l hopper hanger code 1054. 150 l hopper in the picture. Dimensions in mm.

1010


Recommended