23
W-11DE(TLT211-AS)Certified Automotive Lift
W-1
1D
E(T
LT
21
1-A
S)C
ertifie
d A
uto
mo
tive
Lift
W-11DE Certified Installation &Operation Manual
11,000 lb. Capacity
Automotive Lift
Derek Weaver Company,Inc.
2944 SE Loop 820Fort Worth, TX 76140
817-560-9510www.derekweaver.com
LAUNCH TECH USA, INC.
Installation, Operation & Maintenance Manual Two Post Surface Mounted Lift
TLT211-AS
11,000 lbs. Capacity
2,750 lbs. per Arm
1820 S Milliken Ave. Ontario, California 91761 Tel: 562 463-1580 Fax: 562 463-1590 www.launchtechusa.com
IMPORTANT: READ THIS MANUAL COMPLETELY BEFORE
INSTALLING OR OPERATING LIFT
LAUNCH LAUNCH
Launch Model TLT211-AS
General Specifications
Rise height measured with footpads in the highest position.
Lift capacity rating is based on loads equally distributed on all four arms.
Lifting and lowering speeds may vary depending on the weight of the vehicle .
Figure 1-General Specifications and Service Bay Layout
Launch Model TLT211-AS
A. Lifting Height 75.6" (1920mm)
B. Column Height 143" (3634mm) Adjustable to 6" Higher
C. Cylinder Full Height 139.4" (3541mm)
D. Total width 137.8" (3500mm)
E. Drive-Thru Clearance 96" (2438mm)
F. Floor to Overhead Switch 140" (3556mm)
G. Front Arm Reach (min / max) 23.6" 9600mm) / 39.4" (1000mm)
H. Rear Arm Reach (min / max) 38.6" (980mm) / 61.8" (1570mm)
I. Screw Pad Height 4.3" (101mm) to 7.8" (198mm)
J. Inside Column Width 108" (2742mm)
Motor 2 HP
Voltage 208-230Volt/Single Phase
Rise Speed 54 Seconds
Max. Load Per Arm 2750 Lbs.
Ceiling Height Required 143.9" (3525mm)
Optional Column Extension Kit Add 24" (608mm)
VERTICAL CLEARANCE Check the height of the area where the lift is to be installed. Clearance should be based on the full raised height of the lift.
WARNING! Failure by purchaser to
provide adequate clearance could result in unsatisfactory lift performance, property damage, or personal injury. FLOORING
Be certain you have the proper concrete floor to properly handle the loaded lift. Floor should be in generally good condition with no large cracks, spalling or deterioration. **Minimum requirements for concrete are 4 inches minimum depth, with steel reinforcement, 3500 psi, cured for 28 days per local commercial practice. Floor should
be level within 3/8 inch over the installation area. No anchors should be installed within 8 inches of any crack, edge, or expansion joint. If these conditions cannot be met, a new pad must be poured to accommodate the lift. Check with local building inspectors’ and permits office for any special instructions or approvals required for your installation.
WARNING! Failure by purchaser to
provide the recommended mounting surface could result in unsatisfactory lift performance, property damage, or personal injury.
LOCATION This lift has been evaluated for indoor use only with an operating ambient temp. range of 5 - 40°C (41-104°F)
ELECTRICAL REQUIREMENTS For lift installation and operation for single phase units, it is necessary to have a dedicated circuit with a double pole 25 amp circuit breaker or time delay fuse. All electrical connections should be performed by a licensed electrician.
SAFETY NOTICES AND DECALS For your safety, and the safety of others, read and understand all of the safety notices and decals included here.
READ ENTIRE MANUAL BEFORE
ASSEMBLING, INSTALLING,
OPERATING, OR SERVICING
THIS EQUIPMENT.
PROPER MAINTENANCE AND
INSPECTION IS NECESSARY
FOR SAFE OPERATION
DO NOT OPERATE A DAMAGED LIFT
Safety decals similar to those shown here are
found on a properly installed lift. Be sure that all
safety decals have been correctly installed on the
Power Unit reservoir. Verify that all authorized
operators know the location of these decals and
fully understand their meaning. Replace worn,
faded, or damaged decals promptly.
WARNING! Do not attempt to raise a vehicle
on the lift until the lift has been correctly installed and adjusted as described in this manual.
Launch Model TLT211-AS
RECEIVING The shipment should be thoroughly inspected as
soon as it is received. The signed bill of lading is
acknowledgement by the carrier of receipt in
good condition of shipment covered by our
invoice. If any of the goods called for on your bill of lading
are shorted or damaged, do not accept them until
the carrier makes a notation on the freight bill of
the missing or damaged goods. Do this for your
own protection.
Contact Launch Lift immediately if any
hidden loss or damage is discovered after
receipt. IT IS DIFFICULT TO COLLECT FOR LOSS OR
DAMAGE AFTER YOU HAVE GIVEN THE
CARRIER A CLEAR RECEIPT. File your claim with the freight company promptly.
Support your claim with copies of the bill of
lading, freight bill, and photographs.
Major Component Packing List Qty. Description
1 Power Side Column
1 Idler Side Column
2 Overhead Beams
2 Column Extensions
2 Rear Arm Assemblies
2 Front Arm Assemblies
2 Cable Assemblies
1 Hardware Box
1 Hydraulic Hose Kit
2 Lock Covers
1 Hydraulic Power Unit
1 Document Packet
4 Foot Pad Extensions
INSTALLATION IMPORTANT: Always
wear safety glasses while installing lift.
SUGGESTED TOOLS (Minimum Required)
Tape measure, 16ft
Chalk line
4ft level
10" adjustable wrench Metric open end wrenches 10mm,
13mm,14mm,15mm, 17mm, 18mm, 19mm
and 24mm
Needle Nose pliers
Snap Ring pliers
Screw Drivers (Flat and Phillips)
Hammer drill with 3/4" diameter carbide tipped
bits
2 lb. hammer
Torque wrench: 150 foot pounds minimum with
1 1/8" socket
12 ft. Step ladder
Anti-Seize lubricant (for arm pins and foot pad
screw threads and stop rings)
Hydraulic line sealant (Do not use Teflon
tape…this can cause leaking.)
LAYOUT
* Layout the service bay according to the architect's
plans or owners instructions (see Fig 1). Failure to
install in this orientation can result in personal and
property damage. Be certain that the proper
conditions exist, see page 3.
* Assemble column extension to each column using
(12 sets) M12 x 35 Hex bolts, flat washers, lock
washers and nuts. Repeat for opposite column and
extension. Refer to Fig. 2 below.
Figure 2
Launch Model TLT211-AS
3500mm(137.8in)
400mm(15.75in)
2600mm(102.36in)
2810mm(110.63in)
115mm(4.53in)
1＃ 2＃A
B
3
4
3523mm(138.7in)
C
Figure 3
Base plate layout
As shown in Figure.
With total width (A) as the basis, draw two parallel
lines (#1 and #2) on the concrete slab.
Determine the power side column location on any
chalk line, and mark the total width (B) of the base
plate. Mark the points 3 and 4.
Starting from point 3, draw one diagonal line (C) to
the point 5 forming a triangle. In this way, the #1 and
#2 lines can determine the location of the two
columns relative position could be located by
ABCDE.
Notes:
All the dimensions are based on the external
border of the base plate.
The lift layout is very important. If not done
properly, problems may occur during the final
assembly and operation.
Install the power side column
First connect and assemble the column extension with
the power side column, and then raise the power side
column upright to the chalked location. Align the base
plate of column with the chalk line layout. Using the
baseplate as a template, drill holes into the concrete slab
and use the five concrete anchor bolts to attach the
column to the floor. During the drilling process, do not
allow any movement of the column from the chalk line.
Launch Model TLT211-AS
M19×140
250m
m
(9.8
in)
anchor bolts
ExpandDilled hole Clean Fasten
Foundation concrete intensity above3000PSI(2.1Kg/mm )
Column
150m
m
(5.9
in)
2
Column
2
φ19mm(φ0.75in)
4000mm(157.5in)
wide:1800mm(70.9in)
Figure 4
Anchoring
The anchor bolts must be installed at least 8”
away from any crack, edge, or expansion joint.
Use a concrete hammer drill with a ¾ inch
carbide bit. The tip diameter should conform to
ANSI Standard B94.12-1988 (.775 to .787). Do
not use any excessively worm bits or bits which
have been incorrectly sharpened. A core bit may
be necessary if obstructions such as steel rebar
or rocks are encountered. Never substitute
with a shorter or incorrect diameter anchor
bolt.
Recheck overall width dimension, fig. 3. Drill the
anchor holes using the baseplate as a template.
Drill through the floor if possible or at least 6
inches minimum.
Vacuum the dust from the hole to ensure proper
anchor bolt holding power.
Shim column to plumb using the shims provided.
Do not shim more than ½ inch at any given
point. Use a 24 inch or larger level in length to
plumb the columns.
Assemble the washer and nut to anchor with the
nut just below the impact section of the bolt.
Drive the anchor bolt into the hole until the nut
and washer contact the baseplate.
Tighten the anchors and recheck the column for
plumb. Re-shim if necessary. Using a torque
wrench only, tighten to 150 foot lbs. Do not use
an impact gun to tighten the anchor bolts.
Installing the overhead beam
After attaching the column extension to the idler column,
position the idler column at the designated chalk location.
Lift the overhead beam to its highest position and use the
fasteners to attach it to the columns (as shown in Fig. 5).
When installing the overhead beam, ensure the
microswitch support adjacent to the power side column is
positioned at the power side column location. Route the
microswitch cord through the end of the overhead beam
and down the outside of the column as shown in Fig. 10.
Note: Since the idler column is not secured to the
floor by the bolts at this stage, be careful to not move
the idle column as it could tilt over.
Launch Model TLT211-AS
Column
Column extension
16-BoltM12×35
32-Flat washer12
16-Spring washer12
16-NutM12
Overhead beam
8-BoltM12×35
16-Flat washer12
8-Spring washer12
8-NutM12
Figure 5
Finish installing the idler column
Drill holes and install the idler column following the same
procedures as outlined for the power side column.
Install and adjust the steel cables
Raise the two carriages to the safety locking
position (make sure that the safety locks on each
column are fully engaged before attempting to install
cables), and the two carriages are in equal position
from the floor (same height). Install the two steel
cables as shown in Fig. 6.
Adjust the tension of cables through the adjustment
nuts on each end of steel cable. The steel cables
should be tight in equal tension. Each steel cable
should be in the sheave when adjusting tightly,
otherwise the steel cable will be damaged.
Note： Before operating the lift check the steel
cables and verify they are not intersected and are
properly installed. Make sure that the steel cables are
still on the sheaves.
Top sheave
9
Launch Model TLT211-AS
Figure 6
Key points for assembly: the two steel cables shall
be adjusted to equal tension in order to verify the
simultaneous movement of the two carriages.
Install the power unit
Use 5/16x18 bolts and washers (see fig. 7) to
secure the power unit. After the securing of the
power unit. Fill the reservoir with hydraulic oil (oil
capacity of 10L). Operate carefully to avoid dust and
other pollutants mixing with the hydraulic oil.
Connecting the power supply
* Dismantle the sealed cover of the electrical box on the
power unit and do the wiring according to the circuit
diagram. A power supply switch is required to be installed
near the lift for rapidly disconnecting the power supply
during maintenance or in case of emergency. Motor
damage caused by improper wiring is not warranted.
Verify that the oil tank is full; do not operate if there is no
oil. After pressing the up button, if the motor doesn’t run
or abnormal noise or heat occurs, the power unit shall be
immediately stopped to check for proper electrical
connections.
* Connect the microswitch cord as shown in Fig. 10 and Fig.
11.
Figure 7
Note: Do not install this product outdoors.
Motors and electrical controls are not sealed against
weather or moisture. Damage or electrical shock may
occur if installed unprotected outdoors.
Oil filling port Lowering handle
Up button
Launch Model TLT211-AS
Install the Lock Release Cable
Raise lift to a lock position but do not set onto lock. Pull and release power column lock release handle and watch the idler column lock. Adjust cable tension by removing slack in the cable and retightening the cable clamp at the power side.
Figure 8
Connect the hydraulic lines
Install all hydraulic lines and fittings as shown in fig.9.
Clean all piping and hose threads and inspect for
damage. Use oil resistant pipe sealant on all the threads
and tighten properly. Do not use Teflon tape. It is the
installers’ responsibility to insure the system is leak free.
Improperly installed hydraulic fittings are not covered
under warranty
Note: If the hose shall be installed through the
column, ensure that the hose passage will not interfere
with any moving parts.
Figure 9
Fitting
Cylinder
Column
Hose
Fitting
Hose
Power unit
Fitting
8-BoltM12×35
16-Flat washer12
8-Spring washer12
Fitting
Three-way fitting
Hose
Nylon roller
Cable guide block Lock release cable
Power side column
Idler side column
Launch Model TLT211-AS
Proper installation of the overhead microswitch electrical cord
It is very important to keep proper clearance between microswitch electrical cord and the steel cable. Use the provided plastic ties to connect the electrical cord and hose together to avoid any possible damage caused by interference between the electrical cord and the steel cable.
Figure 10
Steel Cable
Hose
Microswitch Electrical Cord
Plastic Tie
Figure 11
Launch Model TLT211-AS
OWNER/OPERATOR CHECKLIST
Demonstrate the operation of the lift to the
owner/operator and review the correct and safe
lifting procedures using the provided Lifting It
Right booklet as a guide.
Complete the installation and review the terms
of the warranty registration card and return the
card to:
Launch Tech USA Inc. 1820 S. Milliken Ave. Ontario, CA. 91761
1-562-463-1580
OPERATION PROCEDURE
SAFETY NOTICES AND DECALS This product is furnished with graphic safety warning labels, which are reproduced on page 2. Do not remove or deface these warning labels, or allow them to be removed or defaced. For your safety, and the safety of others, read and understand all of the safety notices and decals included.
OWNER/EMPLOYER RESPONSIBILITIES
This lift has been designed and constructed according to ANSI/All ALCTV-2006 standard. The standard applies to lift manufactures, as well as to owners and employers. The owner/employer's responsibilities as prescribed by ANSI/All ALOIM-2000, are summarized below. For exact wording refer to the actual standard provided with this manual in the literature package
The Owner/Employer shall insure that lift
operators are qualified and that they are trained
in the safe use and operation of the lift using
the manufacturer's operating instructions;
ALI/SM 93 -1, ALI Lifting it Right safety manual;
ALI/ST- 90 All Safety Tips card; ANSI/ALI
ALOIM-2000, American National Standard for
Automotive Lifts- Safety Requirements for
Operation, Inspection and Maintenance;
ALI/WL Series, ALI Uniform Warning Label
Decals/Placards; and in case of frame
engaging lifts, ALI/LP-GUIDE, Vehicle
Lifting Points/Quick Reference Guide for Frame
Engaging Lifts.
The Owner/Employer shall establish procedures to periodically inspect the lift in accordance with the lift manufacturer's instructions or ANSI/All ALOIM-2000, American National Standard for Automotive Lifts-Safety Requirements for Operation, Inspection and Maintenance; and the employer shall insure that the lift inspectors
are qualified and that they are adequately trained in the inspection of the lift.
The Owner/Employer shall establish procedures to periodically maintain the lift in accordance with the lift manufacturer's instructions or ANSI/ALIOIM-2000, American National Standard for Automotive Lifts-Safety Requirements for Operation, Inspection and Maintenance; and the employer shall insure that the lift maintenance personnel are qualified and that they are adequately trained in the maintenance of the lift.
The Owner/Employee shall maintain the periodic inspection and maintenance records recommended by the manufacturer or ANSI/All ALOIM-2000, American National Standard for Automotive Lifts-Safety Requirements for Operation, Inspection and Maintenance.
The Owner/Employer shall display the lift manufacturer's operating instructions; ALI/SM 93 -1, ALI Lifting it Right safety manual; ALI/ST- 90 ALI Safety Tips card; ANSI/All ALOIM-2000, American National Standard for Automotive Lifts- Safety Requirements for Operation, Inspection and Maintenance; and in the case of frame engaging lift, ALI/LP-GUIDE, Vehicle Lifting Points/Quick Reference Guide for Frame Engaging Lifts; in a conspicuous location in the lift area convenient to the operator.
IMPORTANT SAFETY INSTRUCTIONS
When using your garage equipment, basic
safety precautions should always be followed,
including the following:
1.Read all instructions.
2.Care must be taken as burns can occur from
touching hot parts.
3.To reduce the risk of fire, do not operate equipment in the vicinity of open containers of flammable liquids (gasoline).
4.Keep hair, loose clothing, fingers, and all
parts of body away from moving parts.
5.Use only as described in this manual. Use
only manufacturer’s recommended attachments.
6.ALWAYS WEAR SAFETY GLASSES.
Everyday eyeglasses only have impact resistant lenses, they are not safety glasses.
SAVE THESE INSTRUCTIONS
Launch Model TLT211-AS
LIFTING A VEHICLE
Insure that the lifting arms are parked out to the full drive thru position.
Center the vehicle between the columns in the service bay and position the vehicle's center of gravity midpoint between the columns.
NOTE: the center of gravity is based on the weight distribution and is not the same as the center point of the vehicle.
DO NOT EXCEED 2750 POUNDS PER ARM.
DO NOT ATTEMPT TO LIFT A VEHICLE WITH ONLY ONE OR TWO ARMS, THIS IS UNSAFE AND WILL VOID THE WARRANTY.
INSURE THAT THE HIGHEST POINT ON THE VEHICLE WILL CONTACT THE OVERHEAD LIMIT SWITCH BAR.
DO NOT PLACE THE VEHICLE IN THE SERVICE BAY BACKWARDS.
REFER TO THE VEHICLE MANUFACTURERS SERVICE MANUAL, TECHNICAL BULLETINS, THE "VEHICLE LIFTING POINTS GUIDE" (ALIILP-GUlDE) THAT IS INCLUDED WITH THE LIFT OR OTHER PUBLICATIONS TO LOCATE THE RECOMMENDED LIFTING POINTS.
Position the arms and adapters so all four pads contact the vehicle simultaneously.
The vehicle should remain level during lifting.
Raise the lift until all four wheels are off the ground. Test the stability of the vehicle by attempting to rock the vehicle. Check the adapters for secure contact with the vehicle lift points. If the vehicle seems unstable, lower the vehicle and re-adjust the arms. After re-testing for stability, raise the vehicle 2-3 inches above the desired working height.
Lower the vehicle until the safety latches on both columns engage. The vehicle should remain level when both latches are engaged. If one side engages and the other continues to descend, stop lowering the vehicle, raise it several inches, and try again to engage both latches.
Always lower lift into locks before entering the area beneath the vehicle.
Always use safety stands when removing or installing heavy components. LOWERING A VEHICLE
Insure that the area under the vehicle is clear of personnel, tools toolboxes or service equipment
Raise the vehicle until both latches are free.
Disengage the latches by pulling down and holding the lock release lever.
Lower the vehicle by depressing the lowering valve handle
Continue to lower until the carriages stop against the base plate. Retract the extension arms, and move them away from the vehicle.
MAINTENANCE
To avoid personal injury, permit only qualified
personnel to perform maintenance on this
equipment. Maintenance personnel should follow
lockout /tag out instructions per ANSI Z244.1.
The following maintenance points are suggested as
the basis of a routine maintenance program. The
actual maintenance program should be tailored to the
installation. See ANSI/All ALOIM booklet for periodic
inspection checklist and maintenance log sheet.
If lift stops short of full rise or chatters, check
fluid level and fill per the installation instructions.
Replace all Safety, Warning or Caution Labels
if missing or damaged (See installation
instructions page 2).
Daily
Keep lift components clean.
Check for loose or broken parts.
Check hydraulic system for fluid leaks.
Check adapters for damage or excessive wear.
Replace as required with genuine Launch Lift
parts.
Check lock release activation. When properly
adjusted, the idler column lock should rest
firmly against the back of the column when
engaged and pull clear of the column back
when disengaged.
Weekly
Check synchronizer cables and sheaves for
wear. Replace as required with genuine
Launch Lift parts.
Check lock release cable adjustment per
installation instructions.
Check synchronizer cable tension per
installation instructions. Adjust if necessary.
Monthly
Torque all concrete anchor bolts to 150 ft-Ibs.
Check overhead shutoff switch. While raising
lift, operate overhead shutoff bar. Power Unit
motor should stop when bar is raised.
Lubricate carriage slide tracks with heavy
viscous grease. (Grease all (4) corners of both
columns.)
Visually inspect concrete floor for cracks and/or
spalls within 12" of base plate.
If any problems are encountered, please
contact Launch Tech USA, Inc.
12
Launch Model TLT211-AS
List of lift components
This list is only used as information for the maintenance
and repair. Launch Tech USA will not be liable for other
uses.
In case of damages to the components, purchase can be
made from the Launch Tech USA or its authorized
distributors.
1
2
3
4 5 6
34
3839
11
7
10
5
13
14
15
16
17
18
15
161718
34
35
1219
2010
22
21
23
24
26
2527
28
29
26
30
31
53332
33
32
7
8
10
9
3536
37
40
12
42
13
12
225
201
202
203
204
207
206
205
209
208
210
211212
213
214
215
216
217
218
219
222
220
221
223
224
226
227
229
228
231
230
232
233
13
14
1 201024620 TLT211-AS power side column
2 201024622 TLT211-AS idler column
3 201024624 TLT211-AS column extension
201024626 TLT211-AS column extension(Higher style)
4 201011236 Column bottom cover plate
5 103040132 Flat washer
6 103010498 Screw M5×8
7 201011832 Inner hose hood
8 201014374 Inner hose hood(short)
9 201014679 Long hose at three-way fitting
10 103020188 ScrewM5×10
11 201014685 Shaft for hood installation
12 103050102 Retaining ring28 for shaft
13 201024608 Power unit bracket
14 103020190 ScrewM6×10
15 103020164 BoltM12×35-8.8
16 103040044 Spring washer12
17 103040110 Flat washer12
18 103030129 NutM12
19 201014681 Sheave Spacer
20 201014682 Symmetric shaft
21 201024629 Overhead beam bracket
22 201014672 Switch bracket
23 103030018 Nut M5
24 103010432 ScrewM5X12
25 201014673 Switch shaft
26 103060342 Pin 3*26
27 Limit switch TS-10
28 104130196 Sleeve(inner holeФ22),L=1.8M
29 201014680 Shutoff bar
30 201011477 Shutoff shaft
31 103040134 Washer C,8
32 201024606 Cable guide block assembly
33 103020163 Bolt M6X25
34 201014677 Sheave
35 201013268 Lateral positioning plate
36 103260302 Bushing2820
37 103050032 Retaining ring28 for shaft
15
38 201014678 Retaining ring for shaft end
39 103040122 Spring washer10
40 103020146 Bolt M10×16
41 103260263 Steel cable assembly
103260301 Steel cable assembly( for higher column extension)
42 103020117 Anchor boltM19×140
#N/A
101 Power unit
102 104120159 Power unit hose L=930
103 103202113 Adjustable right angle fitting
104 104120134 Overhead beam hose, L=5370
105 103100294 Three-way fitting
106 104120133 Hose L=930
107 103100323 Flow control fitting assembly
109 103202112 Cylinder
111 103100295 Straight fitting
112 104120160 Idler column hose L=4130
113 104120161 Hose for column extension L=270
104120162 Hose for higher column extension
201 201021093 Carriage
202 104990135 Slide blockⅠ
203 104990134 Slide blockⅡ
204 201012143 Top board
205 103010473 Bolt M10×30
206 103040122 Washer 10
207 103040123 Washer 10
208 104130267 TLT235SB Anti-shock pad,SBR,TLT235SB-20-03-A
209 103010555 Screw M8×12
210 103202184 Restraint shaft assembly
211 103060346 Pin 5X40
212 103060342 Pin 3×26
213 103201914 Spring
214 103201744 Small gear block
215 201012144 Pin shaft
216 103010443 Bolt M10x25
217 103201771 Big gear block
16
218 103050030 Retaining ring 40
219 201024631 Long female arm
220 104130186 Arm rubber pad
221 103010608 Bolt M6x10
222 201024632 Long male arm
223 201024634 Front female arm
224 201024635 Front middle arm
225 201024636 Front male arm
226 104130315 Rubber pad
227 201021561 Threaded rod assembly
228 103202107 Dual-threaded adjustment sleeve
229 103201644 Support bracket
230 103050091 Retaining ring,30
231 103050090 Retaining ring,45
232 201014690 Short extension tube(optional)
201014691 Long extension adaptor(optional)
233 103060392 Pin 10*14
401 104090074 Lock release mechanism hood
402 201012086 Lock release plate
403 201020584 Cam (Power side)
404 103201450 Torsion springⅠ
405 103201451 Torsion spring Ⅱ
406 103201455 Lock release plate shaft
407 202010074 Lock Release roller
408 103201454 Lock release latch
409 103260186 Latch cover BM10×50（black）
412 201011156 Adjustment washer I
413 104130210 Small rubber pad
414 103050021 Retaining ring 9
415 103060333 Pin, 6*40
416 103260179 Cable Clamp 3
417 101060019 Cable,Φ1.4,L=8901
418 103201478 Cable clamp φ2
419 103050025 Retaining ring 20
420 103010393 Screw,M8*12
421 103040134 Washer C,8
422 104090073 Idler lock release mechanism hood
17
Maintenance Records
Form #TLT 211AS 1012011
