Ascom Interoperability Report Cisco WLC 8 6 101 i62 R1 Word - Ascom Interoperability Report Cisco...

Interoperability Report

Ascom i62 Cisco WLC

WLC controller platform

Cisco WLC v. 8.6.101

Ascom i62 v. 6.0.7

Morrisville, NC, USA

February 2018

Interoperability Report Date Page Ascom i62 Cisco WLC 22-Feb-2018 2 / 25

Contents

Introduction ......................................................................................................................................... 3

About Ascom ..................................................................................................................................... 3

About Cisco ....................................................................................................................................... 3

Site Information ................................................................................................................................... 4

Verification site .................................................................................................................................. 4

Participants ........................................................................................................................................ 4

Verification topology .......................................................................................................................... 4

Summary .............................................................................................................................................. 5

General conclusions .......................................................................................................................... 5

Compatibility information ................................................................................................................... 5

Verification overview .......................................................................................................................... 6

Known limitations ............................................................................................................................... 7

Appendix A: Verification Configurations ......................................................................................... 8

Cisco WLC plattform Version 8.6.101 ............................................................................................... 8

Ascom i62 ........................................................................................................................................ 22

Appendix B: Interoperability Verification Records ....................................................................... 25

Document History ............................................................................................................................. 25


Introduction This document describes a summary of the interoperability verification results of the Ascoms and Ciscos platform, necessary steps and guidelines to optimally configure the platforms and support contact details. The report should be used in conjunction with both Ciscos and Ascoms platform configuration guides.

About Ascom Ascom is a global solutions provider focused on healthcare ICT and mobile workflow solutions. The vision of Ascom is to close digital information gaps allowing for the best possible decisions anytime and anywhere. Ascoms mission is to provide mission-critical, real-time solutions for highly mobile, ad hoc, and time-sensitive environments. Ascom uses its unique product and solutions portfolio and software architecture capabilities to devise integration and mobilization solutions that provide truly smooth, complete and efficient workflows for healthcare as well as for industry, security and retail sectors.

Ascom is headquartered in Baar (Switzerland), has subsidiaries in 15 countries and employs around 1,300 people worldwide. Ascom registered shares (ASCN) are listed on the SIX Swiss Exchange in Zurich.

About Cisco Cisco (NASDAQ: CSCO) is the worldwide technology leader that has been making the Internet work since 1984. Our people, products and partners help society securely connect and seize tomorrow's digital opportunity today. Discover more at thenetwork.cisco.com and follow us on Twitter at @Cisco.


Site Information

Verification site Ascom US 300 Perimeter park drive Morrisville, NC, US-27560 USA

Participants Karl-Magnus Olsson, Ascom, Morrisville

Verification topology


Summary

General conclusions Ascom interoperability verification produced very good results with one exception regarding Call Admission Control. For details regarding this and other issue refer to Known limitations on page 7.

Otherwise, authentication, stability and romaing have all been succesful.

Compatibility information One Access point model from every product generation has been selected as a representation (3702 3802 and 1852). By testing these access points we are considered cover all supported major Cisco access points based on chipset compatibility listed below..

Supported Partner Access Points with SW version 8.6.101:

AP1702, 2702, 3702

AP2802, 3802

AP1832, 1852

Supported Partner Controller Platforms with SW version 8.6.101:

Cisco 3504 Wireless Controller



Cisco Virtual Wireless Controller (vWLC) on the following platforms:

VMware vSphere Hypervisor (ESXi) Version 5.x and 6.x

Hyper-V on Microsoft Servers 2012 and later versions


Verification overview

WLAN Compatibility and Performance

High Level Functionality Result Comments

Association, Open with No Encryption OK

Association, WPA2-PSK / AES Encryption OK

Association, PEAP-MSCHAPv2 Auth, AES Encryption OK

Association with EAP-TLS authentication OK

Association, Multiple ESSIDs OK

Beacon Interval and DTIM Period OK

PMKSA Caching OK

WPA2-opportunistic/proactive Key Caching OK

WMM Prioritization OK

802.11 Power-save mode OK

802.11e U-APSD OK

802.11e U-APSD (load test) OK

Roaming, WPA2-PSK, AES Encryption OK * Typical roaming time 55 ms

Roaming, PEAP-MSCHAPv2 Auth, AES Encryption OK ** Typical roaming time 42 ms

Roaming, EAP-FAST, CCKM OK Typical roaming time 30 ms

*) Average roaming times are measured using 802.11a/n. Refer to Appendix B for detailed test results

* *) Measured times is with opportunistic/proactive Key Caching enabled (default enabled)


Known limitations Description and Consequence Workaround Ticket(s)

raised Call admission control / TSPEC is not working correctly with AP3802. All calls are rejected due to exceeded bandwith.

Disable CAC/TSPEC in the system and in handset

Cisco bug CSCvi04088

Note that Cisco AP 1832, 1852 , 2802 and 3802 do not support full CCX and DTPC. Refer to Cisco release notes for additional information.

For additional information regarding the known limitations please contact [email protected] or [email protected]. For detailed verification results, refer to Appendix B: Interoperability Verification Records.


Appendix A: Verification Configurations

Cisco WLC plattform Version 8.6.101

In the following chapter you will find screenshots and explanations of basic settings in order to get a Cisco WLC WLAN system to operate with an Ascom i62. Please note that security settings were modified according to requirements in individual test cases.

Security settings (PSK)

Example of how to configure the system for PSK (WPA2-AES)

Security profile WPA2-PSK, AES encryption

- Select WPA2 Policy with AES encryption. - Select PSK and enter a key (Here in ASCII format)


802.1X authentication (PEAP-MSCHAPv2).

Example of how to configure the system for .1X authentication

Configuration of authentication using external Radius server, 802.1X (Step 1). In this example is WPA2-AES used. Select 802.1X as Authentication Key Management.

Note. To use CCKM, replace 802.1X with CCKM check box. The security mode in the i62 has to be set to Advanced and CCKM has to be selected as Authentication Key Management instead of the default 802.1X.


Example of authentication configuration using external Radius server (Step 2). Select the server to use. The server is configured under tab Security/Radius. See configuration of server below.


Configuration of authentication using external Radius server (Step 3). The IP address and the secret must correspond to the IP and the credential used by the Radius server. Tests were performed using FreeRadius as RADIUS server.

Note. Depending authentication method used it might be necessary to add a certificate into the i62. PEAP-MSCHAPv2 requires a CA certificate and EAP-TLS requires both a CA certificate and a client certificate. Server certificate validation can be overridden in version 4.1.12 and above per handset setting.

Note. Refer to the i62 section in for matching handset configurations.


EAP-FAST using an internal authentication server.

Configuration of authentication using internal Radius server and EAP-FAST (Step 1). In this example is WPA2-AES/CCMP used.

Note. To use CCKM, replace 802.1X with CCKM check box. The security mode in the i62 has to be set to Advanced and CCKM has to be selected as Authentication Key Management instead of the default 802.1X.


Configuration of authentication using internal Radius server and EAP-FAST (Step 2). Check the box Local EAP Authentication and choose your local EAP profile (created in step 4).

Configuration of authentication using internal Radius server and EAP-FAST (Step 3). Create a local user and assign a password.


Configuration of authentication using internal Radius server and EAP-FAST (Step 4). Create a local EAP profile and choose the EAP method to use.


General settings (QoS, Radio)

Set QoS to Platinum (Voice)

Make sure that WMM policy is set to Required


Make sure Session timeout is disabled. Coverage Hole Detection can be left enabled if RRM is used in the system. Set DTIM period to Ascom recommended value 5. DTIM value 5 values are recommended in order to allow maximum battery conservation without impacting the quality. Using a lower DTIM value is possible but will reduce the standby time.

Make sure Client Load Balancing and Clien Band select is disabled.

Make sure 11k Neighbor list is disabled.


Channel configuration. See next picture for additional information.

Ascom recommended settings for 802.11b/g/n are to only use channel 1, 6 and 11. For 802.11a/n/ac use channels according to the infrastructure manufacturer, country regulations and per guidelines below.

Note that Tx power level and channel was manually set for test purpose.

General guidelines when deploying Ascom i62 handsets in 802.11a/n/ac environments:

1. Enabling more than 8 channels will degrade roaming performance. In situations where UNII1 and UNII3 are used, a maximum of 9 enabled channels can be allowed. Ascom does not recommend exceeding this limit.

2. Using 40 MHz channels (or channel-bonding) will reduce the number of non-DFS* channels to two in ETSI regions (Europe). In FCC regions (North America), 20MHz is a more viable option because of the availability of additional non-DFS channels. The handset can co-exist with 40MHz stations in the same ESS.

3. Ascom do support and can coexist in 80MHz channel bonding environments. The recommendations is however to avoid 80MHz channel bonding as it severely reduces the number of available non overlapping channels.

4. Make sure that all non-DFS channel are taken before resorting to DFS channels. The handset can cope in mixed non-DFS and DFS environments; however, due to unpredictability introduced by radar detection protocols, voice quality may become distorted and roaming delayed. Hence Ascom recommends if possible avoiding the use of DFS channels in VoWIFI deployments.

*) Dynamic Frequency Selection (radar detection)


The default data rate set will work just fine, however Ascom recommends disabling the lowest speeds and have 12Mbits as lowest supported speed.

As Ascom i62 do support Channel Switch Announcement its recommended to have this setting enabled in the system (only applicable when DFS channels are used)


Ascom does support both usage of 11n Mode and 11ac Mode including 40 MHz and 80MHz channels

Note. Follow the recommendations General guidelines when deploying Ascom i62 handsets in 802.11a/n/ac environments on Page 16


The default data rate set will work just fine, however Ascom recommends disabling the lowest speeds and have 12Mbits as lowest supported speed. To further optimize performance it is recommended to disallow 802.11b clients to associate by setting 12Mbps rate to mandatory in 802.11g configuration.

Ascom recommends EDCA Profile: Voice Optimized

Make sure Low Latency MAC is disabled. (Both 802.11a/n/ac and 802.11b/g/n)

Note. Using EDCA Profile WMM is acceptable but Voice Optimized is to prefer when voice clients are present in the system.


Depending on the infrastructure (switches) Protocol Type may have to be disabled.


Ascom i62

Network settings for WPA2-PSK

Note. Make sure that the enabled channels in the i62 handset match the channel plan used in the system.

Note. FCC is no longer allowing 802.11d to determine regulatory domain. Devices deployed in USA must set Regulatory domain to USA.


Network settings for .1X authentication (PEAP-MSCHAPv2)


802.1X Authentication requires a CA certificate to be uploaded to the phone by right clicking - > Edit certificates. EAP-TLS will require both a CA and a client certificate.

Note that both a CA and a client certificate are needed for TLS. Otherwise only a CA certificate is needed. Server certificate validation can be overridden in version 4.1.12 and above per handset setting.


Appendix B: Interoperability Verification Records Pass Fail Comments Not verified

16 1 0 7

Total 24

Refer to the attached file for detailed verification results.

Refer to the verification specification for explicit information regarding each verification case. The specification can be found here (requires login): https://www.ascom-ws.com/AscomPartnerWeb/en/startpage/Sales-tools/Interoperability/Templates/

Document History

Rev Date Author Description P1 22-Feb-18 SEKMO Draft R1 7-March-2018 SEKMO Corrections after review. Revison R1

i62

WLAN Interoperability Test ReportWLAN configuration:

Beacon Interval: 100ms

Test object - Handset:DTIM Interval: 5

Ascom i62 version 6.0.7802.11d Regulatory Domain: World

Test object - WLAN system:WMM Enabled (Auto/WMM)

Cisco WLC 3504 Version 8.6.101No Auto-tune

AP 1850, 3700, 3800AP3702AP3800AP1850Single Voice VLAN

2.4Ghz5.0Ghz2.4Ghz5.0Ghz2.4Ghz5.0Ghz

Test CaseDescriptionVerdictVerdictVerdictVerdictVerdictVerdictComment

TEST AREA ASSOCIATION / AUTHENTICATION

#101Association with open authentication, no encryptionNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTED

#107Association with WPA2-PSK authentication, AES-CCMP encryptionPASSPASSPASSPASSPASSPASSHidden SSID validated.

#110Association with PEAP-MSCHAPv2 auth, AES-CCMP encryptionPASSPASSPASSPASSPASSPASSFreeRADIUS server; RootCA loaded to device;FAIL

#111Association with EAP-FAST authenticationPASSPASSPASSPASSPASSPASSWLC internal authtication server

#116Association with EAP-TLS authenticationPASSPASSPASSPASSPASSPASSFreeRADIUS server; Root CA and client cert loaded to device;

TEST AREA POWER-SAVE AND QOSPASS

#150802.11 Power-save modeNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTEDFAIL

#151Beacon period and DTIM intervalPASSPASSPASSPASSPASSPASSBeacon period 100tu, DTIM 1,2,5 verifiedNOT TESTED

#152802.11e U-APSDPASSPASSPASSPASSPASSPASSSee Comment

#202WMM prioritizationPASSPASSPASSPASSPASSPASSIperf for load generation of unprioritized data

TEST AREA "PERFORMANCE"

#308Power-save mode U-APSD WPA2-PSKPASSPASSPASSPASSPASSPASS

#310CAC - TSPECPASSPASSFAILFAILPASSPASScac not working with Ap3800. Bug ID CSCvi04088

TEST AREA ROAMING AND HANDOVER TIMES

#401Handover with open authentication and no encryptionNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTED

#404Handover with WPA2-PSK auth and AES-CCMP encryptionPASSPASSPASSPASSPASSPASSAVG roaming time 11an:55 ms, bgn: 45 ms (No significnat difference seen in roaming times between different AP models)

#408Handover with PEAP-MSCHAPv2 authentication and AES-CCMP encryptionPASSPASSPASSPASSPASSPASSAVG roaming time 11an: 42ms, bgn: 42 ms (No significant difference seen in roaming times between different AP models).

#411Handover using PMKSA and opportunistic/proactive key cachingPASSPASSPASSPASSPASSPASSOKC enabled by default. Same test case as #408

#409EAP-FAST CCKMPASSPASSPASSPASSPASSPASSAVG roaming time an: 30 ms, gn: 35ms (No significant difference seen in roaming times between different AP models).

TEST AREA BATTERY LIFETIME

#501Battery lifetime in idleNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTED

#504Battery lifetime in call with power save mode U-APSDNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTED12h+ in call. Default settings and non-DFS channels only

TEST AREA STABILITY

#602Duration of call U-APSD modePASSPASSPASSPASSPASSPASS>1hrs stable call without interruption

TEST AREA 802.11n

#801Frame aggregation A-MSDUPASSPASSPASSPASSPASSPASSNo frame aggregation in UP6 by default settings.

#802Frame aggregation A-MPDUNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTED

#80440Mhz channelsNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTED

#805802.11n ratesPASSPASSPASSPASSPASSPASSOK

=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2018.02.14 14:50:59 =~=~=~=~=~=~=~=~=~=~=~=show run-config commands 802.11a 11nSupport a-mpdu tx scheduler enable

802.11a 11nSupport a-mpdu tx scheduler timeout rt 10

802.11a 11nSupport a-mpdu tx scheduler timeout nrt 200

802.11a 11nSupport a-msdu max-subframes 3

802.11b 11nSupport a-msdu max-subframes 3

802.11a 11nSupport a-msdu max-length 8k

802.11b 11nSupport a-msdu max-length 8k

802.11a 11nSupport mcs tx 0 disable



802.11a beacon range 0

--More-- or (q)uit 802.11a rx-sop threshold auto default

802.11a cca threshold 0 default

802.11a multicast buffer 0

802.11a multicast data-rate 0 default

802.11a cac voice acm enable

802.11a cac video cac-method static

802.11a max-clients 200

advanced fra sensor-coverage client-priority

advanced fra service-priority coverage

802.11a rate disabled 6

802.11a rate disabled 9

802.11a rate supported 24

--More-- or (q)uit

802.11a cleanair enable network

802.11a dfs-peakdetect enable

802.11b 11nSupport a-mpdu tx scheduler enable

802.11b 11nSupport a-mpdu tx scheduler timeout rt 10

802.11b 11nSupport a-mpdu tx scheduler timeout nrt 200

802.11b beacon range 0

802.11b rx-sop threshold auto default

802.11b cca threshold 0 default

802.11b multicast buffer 0

802.11b multicast data-rate 0 default

802.11b cac voice acm enable

--More-- or (q)uit

802.11b cac video cac-method static

802.11b max-clients 200

802.11b rate disabled 1


802.11b rate disabled 5.5




802.11b rate mandatory 12

802.11b cleanair enable network

802.11h channelswitch enable loud

--More-- or (q)uit aaa auth mgmt local radius

acl url-acl external-server-ip 0.0.0.0

flexconnect fallback-radio-shut disable

flexconnect arp-caching enable

cts inline-tag disable

advanced 802.11a channel dca interval 0

advanced 802.11a channel dca startup-interval 0

advanced 802.11a channel dca anchor-time 0

advanced 802.11a channel dca chan-width best

advanced 802.11a channel dca best-width-max 80

advanced 802.11a channel dca sensitivity 15

advanced 802.11a channel dca min-metric -95

--More-- or (q)uit

advanced 802.11a packet silver max-retry 0

advanced 802.11a packet silver max-packet-count 0

advanced 802.11a packet silver max-client-count 0

advanced 802.11a packet silver timeout 0

advanced 802.11a packet gold max-retry 0

advanced 802.11a packet gold max-packet-count 0

advanced 802.11a packet gold max-client-count 0

advanced 802.11a packet gold timeout 0

advanced 802.11a packet platinum max-retry 0

advanced 802.11a packet platinum max-packet-count 0

advanced 802.11a packet platinum max-client-count 0

--More-- or (q)uit advanced 802.11a packet platinum timeout 0

advanced 802.11a packet bronze max-retry 0

advanced 802.11a packet bronze max-packet-count 0

advanced 802.11a packet bronze max-client-count 0

advanced 802.11a packet bronze timeout 0

advanced 802.11b channel dca interval 0

advanced 802.11b channel dca startup-interval 0

advanced 802.11b channel dca anchor-time 0

advanced 802.11b channel dca sensitivity 10

advanced 802.11b channel dca min-metric -95

advanced 802.11b packet silver max-retry 0

advanced 802.11b packet silver max-packet-count 0

--More-- or (q)uit

advanced 802.11b packet silver max-client-count 0

advanced 802.11b packet silver timeout 0

advanced 802.11b packet gold max-retry 0

advanced 802.11b packet gold max-packet-count 0

advanced 802.11b packet gold max-client-count 0

advanced 802.11b packet gold timeout 0

advanced 802.11b packet platinum max-retry 0

advanced 802.11b packet platinum max-packet-count 0

advanced 802.11b packet platinum max-client-count 0

advanced 802.11b packet platinum timeout 0

advanced 802.11b packet bronze max-retry 0

--More-- or (q)uit advanced 802.11b packet bronze max-packet-count 0

advanced 802.11b packet bronze max-client-count 0

advanced 802.11b packet bronze timeout 0

location info rogue extended

location rssi-half-life tags 0

location rssi-half-life client 0

location rssi-half-life rogue-aps 0

location expiry tags 5

location expiry client 5

location expiry calibrating-client 5

location expiry rogue-aps 5

--More-- or (q)uit advanced 802.11b client-network-preference default

advanced 802.11a client-network-preference default

advanced backup-controller primary

advanced backup-controller secondary

advanced backup-controller

advanced backup-controller

advanced sip-snooping-ports 0 0

advanced eap bcast-key-interval 3600

advanced 802.11-abgn pak-rssi-location threshold -100

advanced 802.11-abgn pak-rssi-location trigger-threshold 10

advanced 802.11-abgn pak-rssi-location reset-threshold 8

--More-- or (q)uit advanced 802.11-abgn pak-rssi-location ntp 192.168.0.12

advanced 802.11-abgn pak-rssi-location timeout 3

advanced hotspot cmbk-delay 1

Cisco Public Safety is not allowed to set in this domain

ap syslog host global ::

ap dtls-cipher-suite RSA-AES128-SHA

ap dtls-wlc-mic sha2

cdp advertise-v2 enable

country SE

countries-list add US

cts sxp disable

--More-- or (q)uit

cts sxp connection default password ****

cts sxp retry period 120

cts sxp sxpversion 2

cts device-id password ****

cts disable

radius auth pac 1 disable

custom-web webmessage ""

custom-web qrscan-bypass-opt 0 0

database size 12000 dhcp create-scope day0-dhcp-mgmt

dhcp address-pool day0-dhcp-mgmt 192.168.1.3 192.168.1.14 dhcp default-router day0-dhcp-mgmt 192.168.1.1

dhcp dns-servers day0-dhcp-mgmt 192.168.1.1

--More-- or (q)uit dhcp lease day0-dhcp-mgmt 600 dhcp network day0-dhcp-mgmt 192.168.1.0 255.255.255.0 dhcp proxy disable

dhcp opt-82 remote-id ap-mac

qos qosmap disable

qos qosmap upstream trust-dscp disable

flexconnect group default-flex-group add

flexconnect group default-flex-group radius ap server-key

flexconnect group default-flex-group radius ap authority id 436973636f0000000000000000000000

flexconnect group default-flex-group radius ap authority info Cisco A_ID

flexconnect group default-flex-group http-proxy ip-address 0.0.0.0 http-proxy port 0

flexconnect group default-flex-group template-vlan-map add none

local-auth eap-profile add LocalEAP

--More-- or (q)uit

local-auth eap-profile cert-issuer cisco LocalEAP

local-auth eap-profile method add fast LocalEAP

local-auth method fast server-key ****

interface address management 192.168.0.60 255.255.255.0 192.168.0.50

interface address virtual 192.0.2.1

interface dhcp management primary 192.168.0.10

interface dhcp management option-6-opendns disable

nasid apgroup default-group

wlan nasid none 1

wlan nasid none 2

wlan nasid none 3

--More-- or (q)uit wlan nasid none 4

interface port management 1 2

mdns snooping disable

mdns policy service-group create "default-mdns-policy" "Default Access Policy created by WLC"

mdns policy service-group user-role add default-mdns-policy admin

mdns profile create "default-mdns-profile"

mdns service create "AirTunes" _raop._tcp.local. origin All LSS disable query disable

mdns service create "Airplay" _airplay._tcp.local. origin All LSS disable query disable

mdns service create "Googlecast" _googlecast._tcp.local. origin All LSS disable query disable

mdns service create "HP_Photosmart_Printer_1" _universal._sub._ipp._tcp.local. origin All LSS disable query enable

mdns service create "HP_Photosmart_Printer_2" _cups._sub._ipp._tcp.local. origin All LSS disable query enable

--More-- or (q)uit mdns service create "HomeSharing" _home-sharing._tcp.local. origin All LSS disable query enable

mdns service create "Printer-IPP" _ipp._tcp.local. origin All LSS disable query disable

mdns service create "Printer-IPPS" _ipps._tcp.local. origin All LSS disable query disable

mdns service create "Printer-LPD" _printer._tcp.local. origin All LSS disable query disable

mdns service create "Printer-SOCKET" _pdl-datastream._tcp.local. origin All LSS disable query disable

mdns service create "http_tcp_local" _http._tcp.local. origin All LSS disable query enable

mdns service create "iTuneWirelessDeviceSharing 2" _apple-mobdev2._tcp.local. origin All LSS disable query disable

mdns service create "printer_extended" _printer._sub._http._tcp.local. origin All LSS disable query enable

mdns profile service add "default-mdns-profile" "AirTunes"

mdns profile service add "default-mdns-profile" "Airplay"

mdns profile service add "default-mdns-profile" "Googlecast"

mdns profile service add "default-mdns-profile" "HP_Photosmart_Printer_1"

--More-- or (q)uit

mdns profile service add "default-mdns-profile" "HP_Photosmart_Printer_2"

mdns profile service add "default-mdns-profile" "HomeSharing"

mdns profile service add "default-mdns-profile" "Printer-IPP"

mdns profile service add "default-mdns-profile" "Printer-IPPS"

mdns profile service add "default-mdns-profile" "Printer-LPD"

mdns profile service add "default-mdns-profile" "Printer-SOCKET"

mdns profile service add "default-mdns-profile" "http_tcp_local"

mdns profile service add "default-mdns-profile" "iTuneWirelessDeviceSharing 2"

mdns profile service add "default-mdns-profile" "printer_extended"

mdns query interval 15

wlan mdns disable 1

--More-- or (q)uit wlan mdns disable 2

wlan mdns disable 3

wlan mdns disable 4

wlan mdns profile 1 "default-mdns-profile"




ipv6 ra-guard ap enable

ipv6 capwap udplite enable all

ipv6 multicast mode unicast

load-balancing aggressive enable

--More-- or (q)uit

load-balancing window 5

wlan apgroup add default-group

wlan apgroup qinq tagging eap-sim-aka default-group enable

wlan apgroup interface-mapping add default-group 1 management




wlan apgroup nac-snmp disable default-group 1




--More-- or (q)uit

memory monitor errors enable

memory monitor leak thresholds 10000 30000Outdoor Mesh Ext.UNII B Domain channels: Disablemesh security rad-mac-filter disablemesh security rad-mac-filter disable

mesh security eapmesh background-scanning disablemesh backhaul rrm disablemesh backhaul rrm auto-rf globalmesh lsc advanced ap-provision open-window enable

mgmtuser add admin **** read-write

mgmtuser termination-interval 0

mobility group domain 3504one

mobility dscp 0

netuser add testuser **** wlan 3 userType permanent description

--More-- or (q)uit

netuser maxUserLogin 5

netuser wlan-id testuser 3

network dns serverip 0.0.0.0

network http-proxy ip 0.0.0.0

network http-proxy Port 80

network secureweb csrfcheck enable

network profiling http-port 80

network ap-priority disabled

network ap-easyadmin disable

global ap virtual IP 0.0.0.0

network fast-ssid-change enable

--More-- or (q)uit network rf-network-name 3504one

network client-ip-conflict-detection disable

pmipv6 mag binding maximum AP 250

port maxspeed 5

qos protocol-type bronze dot1p

qos protocol-type silver dot1p

qos protocol-type gold dot1p

qos protocol-type platinum dot1p

qos priority bronze background background background

qos priority gold video video video

qos priority platinum voice voice voice

--More-- or (q)uit

qos priority silver besteffort besteffort besteffort

qos dot1p-tag silver 0

qos dot1p-tag gold 4

qos dot1p-tag platinum 5

qos max-dscp bronze 10

qos max-dscp silver 0

qos max-dscp gold 34

qos max-dscp platinum 46

radius auth add 1 192.168.0.2 1812 ascii ****

radius callStationIdType macaddr

radius auth callStationIdType ap-macaddr-ssid

--More-- or (q)uit radius auth retransmit-timeout 1 5

radius auth mgmt-retransmit-timeout 1 5

radius fallback-test mode passive

radius fallback-test username cisco-probe

radius fallback-test interval 300

radius dns serverip 0.0.0.0

radius dns disable

radius dns auth network enable

radius dns auth management enable

radius dns acct network enable

radius dns auth rfc3576 disable

radius calea disable

--More-- or (q)uit

radius calea timer 8

tacacs dns serverip 0.0.0.0

tacacs dns disable

rogue detection report-interval 30 rogue detection min-rssi -80 rogue detection transient-rogue-interval 300 rogue detection client-threshold 0 rogue detection security-level high rogue ap aaa-auth disable

rogue ap aaa-auth polling-interval 0

rogue ap ssid alarm

rogue ap valid-client alarm

rogue adhoc enable

rogue adhoc alert

--More-- or (q)uit

rogue ap rldp enable alarm-only monitor-ap-only

rogue auto-contain level 0

rogue containment flex-connect disable rogue containment auto-rate enable rogue client aaa disable

rogue client mse enable

rogue client alert 00:01:3e:11:77:f8

rogue client alert 00:01:3e:11:78:e5

rogue client alert 00:01:3e:11:78:fb

rogue client alert 00:01:3e:12:47:08

rogue client alert 00:01:3e:12:f7:72

rogue client alert 00:01:3e:13:14:b6

--More-- or (q)uit rogue client alert 00:01:3e:17:aa:00

rogue client alert 00:01:3e:17:aa:1b

rogue client alert 00:01:3e:17:b1:c6

rogue client alert 00:01:3e:17:b8:b7

rogue client alert 00:01:3e:17:b8:f9

rogue client alert 00:01:3e:17:b9:07

rogue client alert 00:01:3e:17:d3:35



rogue client alert 00:01:3e:19:f8:5e



--More-- or (q)uit

rogue client alert 00:01:3e:19:f8:c3


rogue client alert 00:01:3e:1a:46:86

rogue client alert 00:01:3e:1a:71:e7

rogue client alert 00:01:3e:1a:71:eb

rogue client alert 00:01:3e:1a:71:ff



rogue client alert 00:01:3e:1a:cd:75

rogue client alert 00:01:3e:1a:e1:0c

rogue client alert 00:01:3e:1a:e5:a1

--More-- or (q)uit rogue client alert 00:15:00:ec:d5:a1

rogue client alert 00:19:70:c0:35:b0

rogue client alert 08:11:96:f0:b3:38

rogue client alert 10:f1:f2:87:6d:34

rogue client alert 20:3c:ae:a1:6d:bd

rogue client alert 20:3c:ae:a2:3a:22

rogue client alert 24:5b:a7:a0:dd:e6

rogue client alert 24:77:03:85:2f:f4

rogue client alert 24:ec:99:51:19:e6

rogue client alert 24:f0:94:0e:df:e5

rogue client alert 34:02:86:b7:ec:83

rogue client alert 34:08:bc:dd:b5:f0

--More-- or (q)uit

rogue client alert 48:51:b7:26:20:be

rogue client alert 48:51:b7:6e:e7:86

rogue client alert 48:bf:6b:98:82:b3

rogue client alert 4c:eb:42:f3:14:ca

rogue client alert 5c:e0:c5:3c:ae:83

rogue client alert 5c:e0:c5:3c:bc:16

rogue client alert 60:57:18:aa:69:e6

rogue client alert 60:a4:d0:ba:23:a6

rogue client alert 64:80:99:8b:a4:e3

rogue client alert 64:80:99:93:ea:bd

rogue client alert 64:80:99:db:dd:fa

--More-- or (q)uit rogue client alert 8c:8e:f2:a4:1e:cd

rogue client alert 94:65:9c:32:71:8e

rogue client alert 9c:d9:17:3f:0a:b6

rogue client alert a0:c9:a0:a9:25:8d

rogue client alert a0:c9:a0:ae:c7:3b

rogue client alert b4:f1:da:b2:30:3c

rogue client alert b8:8a:60:ed:f1:f7

rogue client alert b8:d7:af:11:a6:f7

rogue client alert bc:8c:cd:9d:ed:22

rogue client alert c0:17:4d:44:2d:d7

rogue client alert c4:13:e2:01:1f:14

rogue client alert d0:df:9a:81:3a:a5

--More-- or (q)uit

rogue client alert d8:fc:93:86:e9:8f

rogue client alert e0:b9:a5:fb:bf:ab

rogue client alert ec:9b:f3:be:fc:81

rogue client alert ec:9b:f3:ce:fb:64

rogue client alert f4:0f:24:8b:a8:06

rogue client alert f4:0f:24:d2:78:62

rogue client alert f4:0f:24:d2:7b:d9

rogue client alert f4:0f:24:d2:7c:c9

rogue client alert f8:34:41:85:89:41

snmp version v2c enable

snmp version v3 enable

--More-- or (q)uit snmp snmpEngineId 00003763000092800101fea9

switchconfig strong-pwd case-check enabled

switchconfig strong-pwd consecutive-check enabled

switchconfig strong-pwd default-check enabled

switchconfig strong-pwd username-check enabled

switchconfig strong-pwd position-check enabled

switchconfig strong-pwd case-digit-check enabled

switchconfig strong-pwd minimum upper-case 0

switchconfig strong-pwd minimum lower-case 0

switchconfig strong-pwd minimum digits-chars 0

switchconfig strong-pwd minimum special-chars 0

switchconfig strong-pwd min-length 3

--More-- or (q)uit

sysname 3504one

stats-timer realtime 5

stats-timer normal 180

This command has been deprecated! Please use 'config tacacs auth add' instead.

This command has been deprecated! Please use 'config tacacs auth enable' instead.

This command has been deprecated! Please use 'config tacacs auth server-timeout' instead.

This command has been deprecated! Please use 'config tacacs auth mgmt-server-timeout' instead.

tacacs fallback-test interval 0

time ntp interval 86400

--More-- or (q)uit time ntp server 1 192.168.0.12

rf-profile create 802.11a High-Client-Density-802.11a

rf-profile create 802.11b High-Client-Density-802.11bg

rf-profile create 802.11a Low-Client-Density-802.11a

rf-profile create 802.11b Low-Client-Density-802.11bg

rf-profile create 802.11a Typical-Client-Density-802.11a

rf-profile create 802.11b Typical-Client-Density-802.11bg

rf-profile tx-power-min 7 High-Client-Density-802.11a

rf-profile tx-power-min 7 High-Client-Density-802.11bg

--More-- or (q)uit rf-profile tx-power-control-thresh-v1 -65 High-Client-Density-802.11a

rf-profile tx-power-control-thresh-v1 -60 Low-Client-Density-802.11a

rf-profile tx-power-control-thresh-v1 -65 Low-Client-Density-802.11bg

rf-profile data-rates 802.11a disabled 6 High-Client-Density-802.11a

rf-profile data-rates 802.11a disabled 9 High-Client-Density-802.11a

rf-profile data-rates 802.11a mandatory 12 High-Client-Density-802.11a

rf-profile data-rates 802.11a supported 18 High-Client-Density-802.11a

rf-profile data-rates 802.11a mandatory 24 High-Client-Density-802.11a



--More-- or (q)uit rf-profile data-rates 802.11a supported 54 High-Client-Density-802.11a

rf-profile data-rates 802.11b disabled 1 High-Client-Density-802.11bg


rf-profile data-rates 802.11b disabled 5.5 High-Client-Density-802.11bg



rf-profile data-rates 802.11b supported 9 High-Client-Density-802.11bg

rf-profile data-rates 802.11b mandatory 12 High-Client-Density-802.11bg





--More-- or (q)uit

rf-profile data-rates 802.11a mandatory 6 Low-Client-Density-802.11a

rf-profile data-rates 802.11a supported 9 Low-Client-Density-802.11a







rf-profile data-rates 802.11b mandatory 1 Low-Client-Density-802.11bg

rf-profile data-rates 802.11b mandatory 2 Low-Client-Density-802.11bg

rf-profile data-rates 802.11b mandatory 5.5 Low-Client-Density-802.11bg

--More-- or (q)uit rf-profile data-rates 802.11b mandatory 11 Low-Client-Density-802.11bg

rf-profile data-rates 802.11b supported 6 Low-Client-Density-802.11bg







rf-profile data-rates 802.11a mandatory 6 Typical-Client-Density-802.11a

rf-profile data-rates 802.11a supported 9 Typical-Client-Density-802.11a



--More-- or (q)uit





rf-profile data-rates 802.11b disabled 1 Typical-Client-Density-802.11bg


rf-profile data-rates 802.11b disabled 5.5 Typical-Client-Density-802.11bg



rf-profile data-rates 802.11b supported 9 Typical-Client-Density-802.11bg

rf-profile data-rates 802.11b mandatory 12 Typical-Client-Density-802.11bg

--More-- or (q)uit rf-profile data-rates 802.11b supported 18 Typical-Client-Density-802.11bg




rf-profile rx-sop threshold medium High-Client-Density-802.11a

rf-profile rx-sop threshold medium High-Client-Density-802.11bg

rf-profile rx-sop threshold low Low-Client-Density-802.11a

rf-profile rx-sop threshold low Low-Client-Density-802.11bg

--More-- or (q)uit

rf-profile coverage data -90 Low-Client-Density-802.11a

rf-profile coverage data -90 Low-Client-Density-802.11bg

rf-profile coverage voice -90 Low-Client-Density-802.11a

rf-profile coverage voice -90 Low-Client-Density-802.11bg

rf-profile coverage level 2 Low-Client-Density-802.11a

--More-- or (q)uit rf-profile coverage level 2 Low-Client-Density-802.11bg

rf-profile channel delete 144 High-Client-Density-802.11a

rf-profile channel delete 144 Low-Client-Density-802.11a

rf-profile channel delete 144 Typical-Client-Density-802.11a

rf-profile client-network-preference default High-Client-Density-802.11a

rf-profile client-network-preference default High-Client-Density-802.11bg

rf-profile client-network-preference default Low-Client-Density-802.11a

--More-- or (q)uit rf-profile client-network-preference default Low-Client-Density-802.11bg

rf-profile client-network-preference default Typical-Client-Density-802.11a

rf-profile client-network-preference default Typical-Client-Density-802.11bg

trapflags client nac-alert enable

trapflags client webAuthUserLogin enable

trapflags client webAuthUserLogout enable

trapflags ap ssidKeyConflict disable

trapflags mfp disable

trapflags mesh excessive hop count disable

trapflags mesh sec backhaul change disable

trapflags mesh psk auth failure disable

wlan create 1 CiscoIntopPSK CiscoIntopPSK

--More-- or (q)uit

wlan create 2 CiscoIntop1x CiscoIntop1x

wlan create 3 CiscoIntop2-eapfastcckm CiscoIntop2-eapfastcckm

wlan create 4 CiscoIntop1xCCKM CiscoIntop1xCCKM

wlan nac snmp disable 1




wlan nac radius disable 1




--More-- or (q)uit

wlan multicast interface 1 disable




wlan band-select allow disable 1




wlan ccx aironetiesupport disable 1



--More-- or (q)uit wlan ccx aironetiesupport disable 4

wlan exclusionlist 1 disabled

wlan exclusionlist 1 0

wlan local-auth enable LocalEAP 3

wlan load-balance allow disable 1




wlan assisted-roaming prediction disable 1




--More-- or (q)uit

wlan assisted-roaming neighbor-list disable 1



wlan assisted-roaming neighbor-list enable 4

wlan assisted-roaming dual-list disable 1




wlan dms enable 1

wlan dms enable 2

wlan dms enable 3

--More-- or (q)uit wlan dms enable 4

wlan bssmaxidle enable 1




wlan bss-transition enable 1




wlan bss-transition disassociation-imminent timer 200 1



--More-- or (q)uit


wlan bss-transition disassociation-imminent oproam-timer 40 1




wlan multicast buffer disable 0 1




wlan qos 1 platinum

wlan qos 2 platinum

--More-- or (q)uit wlan qos 4 platinum

wlan dtim 802.11a 5 1




wlan dtim 802.11b 5 1




wlan session-timeout 1 disable



--More-- or (q)uit


wlan flexconnect local-switching 1 disable




wlan flexconnect learn-ipaddr 1 enable




wlan wmm require 1

wlan wmm require 4

--More-- or (q)uit wlan wgb broadcast-tagging disable 1

wlan wgb broadcast-tagging disable 2



wlan wgb prp disable 1




wlan radius_server auth disable 3

wlan radius_server acct disable 3

wlan radius_server auth add 4 1

wlan security splash-page-web-redir disable 1

--More-- or (q)uit




wlan security wpa akm psk enable 1

wlan security wpa akm 802.1x enable 2

wlan security wpa akm cckm enable 3

wlan security wpa akm cckm enable 4

wlan security wpa akm cckm timestamp-tolerance 1000 1




--More-- or (q)uit

wlan security wpa gtk-random disable 1




wlan security pmf association-comeback 1 1




wlan security pmf saquery-retrytimeout 200 1



--More-- or (q)uit wlan security pmf saquery-retrytimeout 200 4

wlan exclusionlist 1 disabled

wlan exclusionlist 1 0

wlan profiling radius dhcp disable 1

wlan profiling radius http disable 1







--More-- or (q)uit

ap hotspot venue type 0 0 AP00A6.CA36.210E

wlan fabric disable 1




wlan fabric encap 0 1




wlan fabric name-vnid-mapping 1


--More-- or (q)uit wlan fabric name-vnid-mapping 3


wlan fabric vnid 0 1




wlan fabric tag 0 1

wlan fabric tag 0 2

wlan fabric tag 0 3

wlan fabric tag 0 4

wlan fabric peer ip 0.0.0.0 1


--More-- or (q)uit







wlan fabric acl 1

wlan fabric acl 2

wlan fabric acl 3

wlan fabric acl 4

wlan fabric avc-policy 1

--More-- or (q)uit wlan fabric avc-policy 2



fabric control-plane tcp timeout 10

fabric control-plane tcp retry-count 3

fabric control-plane tcp keep-alive 10

wlan enable 1

wlan enable 2

wlan enable 3

wlan enable 4

WMM-AC disabled

--More-- or (q)uit HS2 QOS disabled

coredump disable

media-stream multicast-direct disable

media-stream message url media-stream message email media-stream message phone media-stream message note denial media-stream message state disable

802.11a media-stream multicast-direct enable802.11b media-stream multicast-direct enable

802.11a media-stream multicast-direct radio-maximum 0802.11b media-stream multicast-direct radio-maximum 0

802.11a media-stream multicast-direct client-maximum 0

--More-- or (q)uit802.11b media-stream multicast-direct client-maximum 0

802.11a media-stream multicast-direct admission-besteffort disable802.11b media-stream multicast-direct admission-besteffort disable

802.11a media-stream video-redirect enable802.11b media-stream video-redirect enable

ipv6 neighbor-binding timers reachable-lifetime 300

ipv6 neighbor-binding timers stale-lifetime 86400

ipv6 neighbor-binding timers down-lifetime 30

ipv6 neighbor-binding ra-throttle disable

ipv6 neighbor-binding ra-throttle allow at-least 1 at-most 1

ipv6 neighbor-binding ra-throttle max-through 10

ipv6 neighbor-binding ra-throttle throttle-period 600

ipv6 neighbor-binding ra-throttle interval-option passthrough

--More-- or (q)uit

ipv6 ns-mcast-fwd disable

ipv6 na-mcast-fwd enable

ipv6 enable

nmheartbeat disable

ipv6 slaac service-port disable

sys-nas

tunnel eogre heart-beat interval 60

tunnel eogre heart-beat primary-fallback-timeout 30

tunnel eogre heart-beat max-skip-count 3

wlan mobility selective-reanchoring disable 1


--More-- or (q)uit wlan mobility selective-reanchoring disable 3


cloud-services wsa mode Disable

network assurance server url

Sensor Provisioning Interface Name None

Sensor Provisioning Disable

WSA Backhaul SSID

WSA Backhaul Username

WSA Backhaul Authentication Type psk

Eap Type ........................................ cloud-services server url

--More-- or (q)uit

cloud-services cmx disabled

network assurance sync-interval Fixed

network assurance on-change Disable

usb enable

WLAN Express Setup - True

Flex Avc Profile Configuration

opendns global status is disabled

opendns forced global status is disabled

wlan 1 opendns vap mode is ignore

--More-- or (q)uit wlan 2 opendns vap mode is ignore



Fabric Configuration fabric disable

(Cisco Controller) >? clear Clear selected configuration elements.config Configure switch options and settings.cping Send capwap echo packets to a specified mobility peer IP address.debug Manages system debug options.eping Send Ethernet-over-IP echo packets to a specified mobility peer IP address.grep Print lines matching a pattern.help Helplicense Manage Software Licenselinktest Perform a link test to a specified MAC address.logout Exit this session. Any unsaved changes are lost.mping Send Mobility echo packets to a specified mobility peer IP address.ping Send ICMP echo packets to a specified IP address.reset Reboot (hard reload) options.save Save switch configurations.show Display switch options and settings.test Test trigger commandstransfer Transfer a file to or from the switch. (Cisco Controller) >? clear Clear selected configuration elements.config Configure switch options and settings.cping Send capwap echo packets to a specified mobility peer IP address.debug Manages system debug options.eping Send Ethernet-over-IP echo packets to a specified mobility peer IP address.grep Print lines matching a pattern.help Helplicense Manage Software Licenselinktest Perform a link test to a specified MAC address.logout Exit this session. Any unsaved changes are lost.mping Send Mobility echo packets to a specified mobility peer IP address.ping Send ICMP echo packets to a specified IP address.reset Reboot (hard reload) options.save Save switch configurations.show Display switch options and settings.test Test trigger commandstransfer Transfer a file to or from the switch. (Cisco Controller) >? clear Clear selected configuration elements.config Configure switch options and settings.cping Send capwap echo packets to a specified mobility peer IP address.debug Manages system debug options.eping Send Ethernet-over-IP echo packets to a specified mobility peer IP address.grep Print lines matching a pattern.help Helplicense Manage Software Licenselinktest Perform a link test to a specified MAC address.logout Exit this session. Any unsaved changes are lost.mping Send Mobility echo packets to a specified mobility peer IP address.ping Send ICMP echo packets to a specified IP address.reset Reboot (hard reload) options.save Save switch configurations.show Display switch options and settings.test Test trigger commandstransfer Transfer a file to or from the switch. (Cisco Controller) >? clear Clear selected configuration elements.config Configure switch options and settings.cping Send capwap echo packets to a specified mobility peer IP address.debug Manages system debug options.eping Send Ethernet-over-IP echo packets to a specified mobility peer IP address.grep Print lines matching a pattern.help Helplicense Manage Software Licenselinktest Perform a link test to a specified MAC address.logout Exit this session. Any unsaved changes are lost.mping Send Mobility echo packets to a specified mobility peer IP address.ping Send ICMP echo packets to a specified IP address.reset Reboot (hard reload) options.save Save switch configurations.show Display switch options and settings.test Test trigger commandstransfer Transfer a file to or from the switch. (Cisco Controller) >? clear Clear selected configuration elements.config Configure switch options and settings.cping Send capwap echo packets to a specified mobility peer IP address.debug Manages system debug options.eping Send Ethernet-over-IP echo packets to a specified mobility peer IP address.grep Print lines matching a pattern.help Helplicense Manage Software Licenselinktest Perform a link test to a specified MAC address.logout Exit this session. Any unsaved changes are lost.mping Send Mobility echo packets to a specified mobility peer IP address.ping Send ICMP echo packets to a specified IP address.reset Reboot (hard reload) options.save Save switch configurations.show Display switch options and settings.test Test trigger commandstransfer Transfer a file to or from the switch. (Cisco Controller) >? clear Clear selected configuration elements.config Configure switch options and settings.cping Send capwap echo packets to a specified mobility peer IP address.debug Manages system debug options.eping Send Ethernet-over-IP echo packets to a specified mobility peer IP address.grep Print lines matching a pattern.help Helplicense Manage Software Licenselinktest Perform a link test to a specified MAC address.logout Exit this session. Any unsaved changes are lost.mping Send Mobility echo packets to a specified mobility peer IP address.ping Send ICMP echo packets to a specified IP address.reset Reboot (hard reload) options.save Save switch configurations.show Display switch options and settings.test Test trigger commandstransfer Transfer a file to or from the switch. (Cisco Controller) >? clear Clear selected configuration elements.config Configure switch options and settings.cping Send capwap echo packets to a specified mobility peer IP address.debug Manages system debug options.eping Send Ethernet-over-IP echo packets to a specified mobility peer IP address.grep Print lines matching a pattern.help Helplicense Manage Software Licenselinktest Perform a link test to a specified MAC address.logout Exit this session. Any unsaved changes are lost.mping Send Mobility echo packets to a specified mobility peer IP address.ping Send ICMP echo packets to a specified IP address.reset Reboot (hard reload) options.save Save switch configurations.show Display switch options and settings.test Test trigger commandstransfer Transfer a file to or from the switch. (Cisco Controller) >? clear Clear selected configuration elements.config Configure switch options and settings.cping Send capwap echo packets to a specified mobility peer IP address.debug Manages system debug options.eping Send Ethernet-over-IP echo packets to a specified mobility peer IP address.grep Print lines matching a pattern.help Helplicense Manage Software Licenselinktest Perform a link test to a specified MAC address.logout Exit this session. Any unsaved changes are lost.mping Send Mobility echo packets to a specified mobility peer IP address.ping Send ICMP echo packets to a specified IP address.reset Reboot (hard reload) options.save Save switch configurations.show Display switch options and settings.test Test trigger commandstransfer Transfer a file to or from the switch. (Cisco Controller) >? clear Clear selected configuration elements.config Configure switch options and settings.cping Send capwap echo packets to a specified mobility peer IP address.debug Manages system debug options.eping Send Ethernet-over-IP echo packets to a specified mobility peer IP address.grep Print lines matching a pattern.help Helplicense Manage Software Licenselinktest Perform a link test to a specified MAC address.logout Exit this session. Any unsaved changes are lost.mping Send Mobility echo packets to a specified mobility peer IP address.ping Send ICMP echo packets to a specified IP address.reset Reboot (hard reload) options.save Save switch configurations.show Display switch options and settings.test Test trigger commandstransfer Transfer a file to or from the switch. (Cisco Controller) >? clear Clear selected configuration elements.config Configure switch options and settings.cping Send capwap echo packets to a specified mobility peer IP address.debug Manages system debug options.eping Send Ethernet-over-IP echo packets to a specified mobility peer IP address.grep Print lines matching a pattern.help Helplicense Manage Software Licenselinktest Perform a link test to a specified MAC address.logout Exit this session. Any unsaved changes are lost.mping Send Mobility echo packets to a specified mobility peer IP address.ping Send ICMP echo packets to a specified IP address.reset Reboot (hard reload) options.save Save switch configurations.show Display switch options and settings.test Test trigger commandstransfer Transfer a file to or from the switch. (Cisco Controller) >? clear Clear selected configuration elements.config Configure switch options and settings.cping Send capwap echo packets to a specified mobility peer IP address.debug Manages system debug options.eping Send Ethernet-over-IP echo packets to a specified mobility peer IP address.grep Print lines matching a pattern.help Helplicense Manage Software Licenselinktest Perform a link test to a specified MAC address.logout Exit this session. Any unsaved changes are lost.mping Send Mobility echo packets to a specified mobility peer IP address.ping Send ICMP echo packets to a specified IP address.reset Reboot (hard reload) options.save Save switch configurations.show Display switch options and settings.test Test trigger commandstransfer Transfer a file to or from the switch. (Cisco Controller) >? clear Clear selected configuration elements.config Configure switch options and settings.cping Send capwap echo packets to a specified mobility peer IP address.debug Manages system debug options.eping Send Ethernet-over-IP echo packets to a specified mobility peer IP address.grep Print lines matching a pattern.help Helplicense Manage Software Licenselinktest Perform a link test to a specified MAC address.logout Exit this session. Any unsaved changes are lost.mping Send Mobility echo packets to a specified mobility peer IP address.ping Send ICMP echo packets to a specified IP address.reset Reboot (hard reload) options.save Save switch configurations.show Display switch options and settings.test Test trigger commandstransfer Transfer a file to or from the switch. (Cisco Controller) >

Date post:	08-Apr-2018
Category:	Documents
Upload:	trinhthu
View:	317 times
Download:	14 times

Ascom Interoperability Report Cisco WLC 8 6 101 i62 R1 Word - Ascom Interoperability Report Cisco...

Documents