ASHLOK

Presents

Safe Earthing Electrode (ASEEL)

“ YOUR SAFETY IS OUR RESPONSIBIlITY”

Need For Superior Earthing

Industrial Revolution and Infrastructure Development

Electronic Boom in the 1980’s

Requirement of Precise Ohmic Values for various applications

Protection from chaotic electrical Hazards

NOT TO BE FORGOTTEN: Human Safety Infrastructure Safety

EARTHING SYSTEM

Earth PitConductive ElectrodesSoil Enhancing Compound

Significance of Good Earthing

Low impedance Resist CorrosionSufficient Mechanical strength to hold fault current

Earth Resistance

Varies with different soils To be Checked before earthing the site Decide the earthing system for the requirement

TECHNOLOGY & STRUCTURE

Pipe In Pipe Technology

Coaxial Pipes ( One inside the other)

Adequate Mechanical strength

Galvanized or

Coated for effective corrosive resistance

Ashlok Earthing – Features

Crystalline Conductive Mixture (CCM):

Contains metal alloys and natural compounds

CCM is an unique mixture having.

Excellent conductivity. High specific gravity. Anti-corrosive Properties. Excellent bonding properties.

Ashlok Earthing – Features

Back Fill Compound (BFC) : After erecting the pipe in the earth pit the BFC is mixed with water and filled around the pipe.

Not soluble & part of the earth pit. Hydroscopic in nature. Enhances performance of electrode – Electrolytic Gel solution. Maintains moisture and enhances conductivity around the electrode. Does not leach in to the normal soil. Reduces soil resistivity around the electrode.

Ashlok Earthing - BenefitsScientifically developed, Readymade and Standardized

Maintenance Free

Consistency

Larger surface area

Low earth resistance

Corrosion resistant & Eco friendly

Long life – 15 -20 yrs

As per IS 3043:1987 standards

TECHNICALITIES

ASEEL 19 ( 3 Mtrs ) Dia 50mm20 KA /sec of rms51 KA peak value

ASEEL 39 ( 3 Mtrs ) Dia 80mm40 KA /sec of rms100 KA peak value

Ashlok Earthing – Specially Coated Electrodes

Advanced SPM ( Special Purpose Machine ) technology80 – 100 microns of coating on the outer pipe.Customized as per application & requirement

SPM BenefitsThick CoatingUniformityMat Finish

Products in 2009Zinc coated Copper coatedAlloy coated

Installation – Normal Soil

3 M Electrode – Normal Soil

Augur a hole of 10” Diameter and 10’ in depth.

Put BFC at the bottom of the pit (App 5 Kgs)

Place the electrode in the middle of the pit.

Filter the mother soil (taken out during auguring) - mix the BFC with the soil.

Start putting the mixture around the electrode with adequate supply of water in the pit.

•With a long stick, start poking the sides of the pits to help in mixing the compound well and to remove the air bubbles.

•Fill the pit completely with the compound mixture and pour abundant water in and around the pit.

•Leave the pit to rest for a day.

•Construct a chamber and provide connection to the equipment.

Installation – Normal Soil

Achievements & Credentials Best product award – Elecrama 2008

Accomplished the toughest installation in remote regions of India, under the harshest conditions

Our electrode has the distinction of being the only Earthing product to withstand the highest short circuit current tested by CPRI

Successfully converted our 1st Annual turnover into daily turnover

Some Prominent Customers

Some Prominent Customers

Some Prominent Customers

Some Prominent Customers

Some Prominent Customers

Some Prominent Customers

Some Prominent Customers

Railways and Aviation Railways and Aviation

• ASHLOK SEE

• Long term – (15 – 20 yrs)• One Time investment

• Maintenance Free• Better Ohmic Value

• CONVENTIONAL

• Short Term ( 1 – 2 yrs )• Repetitive Investment• Continuous maintenance• Unpredicted Ohmic Value

Performance, Value, Safety & Good price (Vs) Only less COST

Please Act Smart & Fast - Be Safe

THANK YOU

“”