ASME B73.1
Chemical
Processing
Pump
Wilfley
M o d e l A 7
Technical Handbook
Wilfley Model A7 Chemical Processing Pumps
Wilfley hydraulic seal in actual operation.
ASME B73.1 M-91
Wilfley’s Model A7 pump seriesoffers maximum efficiency coupledwith ultimate seal flexibility. It isdesigned to be sealless, but canalso be used with virtually anytraditional seal—packing ormechanical.
The Model A7 is an end-suction,single-stage centrifugal pump thatmeets ASME B73.1 M-91requirements. It handles liquids thatare highly corrosive and abrasive.Discharge sizes range from 1" to 8"in diameter. Flow rates range to4,500 gallons per minute.
Original Sealless Operation
To prevent leakage while running,Model A7 pumps have the originalWilfley expeller. The impeller andexpeller rotate together during
operation creating a hydraulic sealthat keeps liquids away from theshaft while the pump is operating.
Static seal faces prevent leakagewhen the pump is shut down. Thepump remains leak free whilerunning and while shut down.
Wilfley seals can be run dry withoutdamaging internal parts becausewetted parts operate freely with norubbing contact. Constant downtime to repair and replaceconventional contact seals iseliminated.
Ultimate Flexibility
Wilfley Model A7 pumps aredesigned to handle a wide range ofcorrosive applications—no matterwhat the requirements. Wilfleyengineers each pump to perform toexact specifications.
Discharge
Pump Running/Seal Open
Pump Off/Seal Closed
Imp
elle
r
Exp
elle
r
Suction
A.R. Wilfley & Sons is proud of theindividual engineering servicetraditionally provided to customers.Wilfley engineers have developednew sealing flexibility in answer tocustomers’ requests.
The DryLock® and Lube Seal arenow exclusively available throughWilfley for the Model A7. The Model A7 can also use most otheravailable seals. This flexibilityextends to vapor seals. The A7series frame can use conventionallip seals, labyrinth or magnet seals.
Tradition of Innovation and Quality
Arthur Redman Wilfley was aninventor and entrepreneur. Hebegan working on centrifugalpumps in 1902. Wilfley’s firstcommercially-available pump wassold in 1919 and was built aroundhis unique concept of the expellerfor hydraulic sealing. He continuedto perfect the expeller design andreceived a patent in 1920. Theexpeller is now the hallmark of allWilfley pumps.
Today, Wilfley’s applications andengineering staff continue toprovide the most up-to-dateinformation and innovativetechnology on pumps and pumpprocesses to customers around theworld.
Wilfley’s pump lines include a widerange of centrifugal pumps that aredesigned to handle highly-abrasiveslurries and corrosive materials.
To locate the Wilfley office or agentnearest you, please contact A.R. Wilfley & Sons, Inc. directly at 1-800-525-9930 orwww.wilfley.com.
Impeller pumps liquidfrom suction todischarge.
Expeller createspressure keepingliquid from shaft.
2
Wilfley Model A7 Features and Benefits
Centrifugally actuatedseal provides smoothand efficient sealopening and closing.
Extra case wall thicknessextends wear life.
Rotary andstationary sealfaces are openduring operationand closed toprevent leakagewhen the pumpis shutdown.
Large impellervanes providehighly-efficientpumping withlong wear life.
Baseplate and frame are heavy cast iron with heavyrib reinforcements made to withstand severe operatingloads. Non-metallic and fabricated baseplates are available.
The Wilfley expelleris a non-contacting,hydrodynamic sealthat provides long,trouble-free life andminimal operatingcost and downtime.
Frame support toease assembly.
Shaft is isolated fromliquid. Sleeves availablein wide variety of alloys.
Large oil sump capacityto provide maximumcooling and increasebearing life.
Bearings designedfor long life. Bearingseats are ground toprovide a precise fit.
Optimum shaft sizeto transmit loads andmaximize sealing flexibility.
Cartridge-type Wilfleyhydronamic seal tosimplify maintenance.
Optional vapor sealmeets EPA requirements.
Close-fitting lip excludescontaminants from primaryseal.
Guards isolateall moving parts.
Wide range ofmaterials available.
Standard labyrinth seal
Pump Running/Seal Open
Pump O�/Seal Closed
DryLock ® Features
The DryLock ® uses the action ofcentrifugal force combined with thesmooth actuation of ball bearings toopen and close the seal. As thepump starts up, the expellerevacuates the liquid in the sealarea. The balls of the DryLock ® areforced outward and slide up a rampcreated by the ball housing. Theramp forces the balls into theactuator plate and opens the sealfaces. Upon shut-down, the ballslose their centrifugal force allowingthe spring-loaded actuator plate tomove back into its closed position.The seal is then closed.
Wil�ey DryLock ® Seal
Symmetricalactivationmechanism.
Positive seal atshutdowntightens withpressure.
Multiple sealface materialsavailable.
Simple replaceableparts.
No rubbing components.
Hook sleeve designfor maximum shaftprotection.
Isolated spring forreliable seal action.
Seal activation can easily bechanged to open and closeat di�erent speeds simply byadding or subtracting balls.
Actuator Assembly
5
ey Options Seal
6
Drylock/Labyrinth BackupFor Light Slurry Services
Mechanical Seal
Diaphram Seal
Extreme Temperature Seal
Expeller/Packing
Carbon Drylock/Drain SealFor Fine Solids Services
Model A7 Pump Capacities
7
60 cycle performance
100
200
300
400
700
600
500
AA-81x1.5-8
A20-133x1.5-13
A06-102x1-10
100FLOW (GPM)
HE
AD
(FT
)
3550 RPM
10 100001000
AB-63x1.5-6
A50-103x1.5-10
A50-83x1.5-8
A30-13 3x2-13
A70-84x3-8
A60-83x2-8
A60-103x2-10
AA-61.5x1-6
A70-104x3-10
20
40
60
80
100A110-16 8x6-16S
A80-106x4-10
A110-158x6-15
A120-1510x8-15
A120-1610x8-16S
100FLOW (GPM)
HE
AD
(FT
)
1150 RPM
1 10 100001000
A20-133x1.5-13
A70-104x3-10
A80-136x4-13
A30-133x2-13
A40-134x3-13
A50-103x1.5-10
A60-103x2-10
A05-102x1-10
60
110
160
210A110-16 8x6-16S
AA-8 1x1.5-8
AA-6 1.5x1-6
A20-133x1.5-13
A06-10 2x1-10A110-158x6-15
A120-1510x8-15
A120-1610x8-16S
100FLOW (GPM)
HE
AD
(FT
)
1750 RPM
10 100001000
A50-83x1.5-8
AB-6 3x1.5-6
A70-104x3-10
A80-106x4-10
A60-8 3x2-8A70-84x3-8
A80-136x4-13
A30-133x2-13
A40-134x3-13
A50-103x1.5-10
A60-103x2-10
8
10
30
50
70
90
110
130
150
170
AA-8 1x1.5-8
AA-6 1.5x1-6
A20-133x1.5-13
A06-102x1-10
100FLOW (M3/HR)
HE
AD
(M)
2950 RPM
1 10 1000
A50-103x1.5-10
AB-63x1.5-6
A70-84x3-8A60-8 3x2-8
A70-104x3-10
A80-106x4-10
A30-133x2-13
A40-134x3-13
A50-83x1.5-8
A60-103x2-10
50 cycle performance
10
20
30
40
50
A110-16 8x6-16S
AA-8 1x1.5-8
AA-6 1.5x1-6
A20-133x1.5-13
A06-102x1-10
A110-158x6-15
A120-1510x8-15
A120-1610x8-16S
100FLOW (M3/HR)
HE
AD
(M)
1450 RPM
1 10 100001000
A50-83x1.5-8
AB-63x1.5-6
A70-104x3-10
A80-106x4-10
A60-8 3x2-8
A70-84x3-8
A80-136x4-13
A30-133x2-13
A40-134x3-13
A50-103x1.5-10
A60-103x2-10
Materials
Item Number
11a34
141517
6161a61b62
62a62b62c6772
72a72b73757679
Wet End ItemName
CasingCap ScrewGasket, CasingLockwasherImpellerCasing PlateExpeller
FramePlugDrain PlugShaftBearing, InboardBearing, OutboardLocknutOil Seal, InboardBearing CarrierO-ring, Bearing CarrierJam NutRetaining RingCap ScrewOil Seal, OutboardSight Glass
DryLock®
Alloy 20
A2018-8
18-8Te�on® Te�on®Te�on®Te�on®
A20A20A20
DI**MS
SteelWMS*SteelSteelSteel
DI**Viton®18-8Steel18-8
18-8
A20
Material316SS
316SS18-8
18-8316S316S316S
DI**MS
SteelWMS*SteelSteelSteel
DI**Viton®18-8Steel18-8
18-8
316SS
WCD4™
WCD4™
WCD4™WCD4™WCD4™
WCD4™
18-8
18-8
DI**MS
SteelWMS*SteelSteelSteel
DI**Viton®18-8Steel18-8
18-8
Ductile Iron
DI**18-8
18-8DI**DI**DI**
DI**MS
SteelWMS*SteelSteelSteel
DI**Viton®18-8Steel18-8
18-8
DI**
Power End
Seals
Materials
7centrifugal pumps in a variety ofmaterials to meet a wide variety ofpumping conditions.
Model A7 pumps have beenmanufactured in ductile iron, duplex,stainless steel, nickel alloys, hard irons,and a variety of austenitic stainlesssteels including; Alloy 20 (CN7M) 304L(CF3), 316L (CF3M).
eknowledge and experience to assist
ymaintains an extensive library of pumping services and
yf
abrasion and corrosion on a widevariety of materials.
lresources have developed uniquematerials to survive in the most hostileenvironments. These proprietarymaterials were developed to extendthe erosion - corrosion performanceand reliability of the A7 pump underextreme conditions.
WCD4 – u%
higher hardness, 42% increase intensile strength, 65% increase in yieldstrength, resulting in a lower wear rateand higher corrosion resistance thanthe industry standard CD4MCu.
MAXALLOY® 5 – High chrome whiteiron providing a material hardness up to 650 HBN and 4 to 9.5 pHoperating range.
MAXALLOY® 8 – A proprietary highchrome white iron providing 450-520HBN hardness, able to withstandchemical deterioration within a 1.3 to13.2 pH range.
To assist with proper materiall
coupons for testing in your particularapplication followed by a materialdeterioration analysis report.
* WMS – hardened steel** DI – ductile iron
9
Te�on® Te�on®Te�on®Te�on®
Te�on® Te�on®Te�on®Te�on®
14 17 15 67 62a 61 61a 62
62b 62c 72b 75
72
76
72a
75
4
73
7961b1a413
10
Model A7 Options and Engineering Specials
Features Options Engineered Specials
Bearings – single row Extreme duty bearingsSingle row deep groove – inboard bearingDuplex angular contact – outboard
Oil lubricated bearings Grease, oil mist, constant level oiler
Labyrinth bearing seal Magnetic Bearing SealOil Filter
Frame and bearing carrier material: 316SS Corrosion resistant alloysDuctile iron
Frame with large sight glass Sight glass on the opposite side oron the right side when viewed on both sidesfrom coupling end. Oil cooling provisions
O-Ring material: Viton Kalrez®
Teflon® encapsulated
Wet end material: DI, 316SS, A20, 1/2" NPT connection for case drain 1/4" NPT connection for gaugeWCD4™, High Nichol Alloy, Max5/Ma8 Steam jackets Alloys – special order
150 lbs. raised faced flanges 300 lbs raised faced flanges
DryLock® seal PackingMechanical seal
Labyrinth seal Lube seal
Flush connections for seals Flushing hardwareExpeller cavity drain
Special Modifications
A.R. Wilfley & Sons is dedicated tomanufacturing pumps that maximizetheir full potential. Wilfley routinelyaccommodates customer requestsfor steam jackets, special paint,flush ports, special drain plugs andother modifications required to fitspecific needs.
Many applications require specialmotor and drive configurations,including baseplates and mountingbrackets. Non-metallic andfabricated baseplates are available.
Wilfley engineers assist in anyspecial configurations that the liquidand process require. Wilfley’sfamous high-quality workmanshipapplies to all special designs tocustomers’ needs.
11
Construction Details
12
Frame 1 Frame 2 Frame 3 Frame 4
AA-6 AB-6 AA-8 A5O-8 A60-8 A70-8 A05-10 A50-10 A60-10 A70-10 A80-10 A20-13 A30-13 A40-13 A80-13 A110-15 A120-15General
Pump weight 137lbs 167 152 371 375 411 420 468 473 492 549 478 490 528 574 1090 120762 kg 76 69 168 170 186 191 212 215 223 249 217 222 240 260 494 547
Max. working* 250 °F 250 250 250temperature 120 °C 120 120 120
Max. working 200 psi 200 200 200pressure 675 kPa 675 675 675
Max. solids size 3/16 in. 1/4 5/16 1/4 1/4 3/8 1/4 3/8 3/8 3/8 3/8 1/4 3/8 3/8 3/8 1/2 1/25 mm 6 8 6 6 10 6 10 10 10 10 6 10 10 10 13 13
Shaft
Diameter at .75 in. 1 1.125 2.125Impeller 19 mm 25.4 28.6 53.9
Diameter at 1.375 in. 1.375 1.875 2.123Sleeve 34.9 mm 34.9 47.6 53.9
Diameter at .875 in. 1.125 1.125 2.375Coupling 22.2 mm 28.5 28.5 60.3
Diameter 1.94 in. 2.5 2.84 4.41between 49.3 mm 63.5 72.1 112bearings
Shaft 6.413 in. 6.85 7.79 10.21overhang 162.9 mm 173.9 197.9 259.3
Bearing span 3.175 in. 7.71 6.63 9.9980.6 mm 195.8 168.4 253.7
Bearings
Standard radial 6308 6311 6312 6319Abearing
Standard thrust 5208A 5211A 5312 7319BECBbearing
Extreme duty 6308 311M 312M NU319ECradial bearing
Extreme duty 7308BECB 7310BECB 7312BECB 7319BECBthrust bearing
*Modified seal configurations are available for special pumping conditions up to 400º F.
Dimensions
The dimensions listed above conformto ASME B73.1 specifications andapply to fabricated and non-metallicbase plates only. dimensions aredifferent for iron bases.
These dimensions are not forconstruction. Certified dimensionprints are available for your specificinstallation.
All dimensions printed in black are ininches and those in red are theapproximate equivalent in millimeters.
Flanges are drilled to match ASMEB16.5 150lbs.
13
PumpGroup
1
2
3
Size, Suction X Discharge XNominal Impeller Diameter
1.5 X 1 X 6 (40 X 25 X 150)3 X 1.5 X 6 (80 X 40 X 150)1.5 X 1 X 8 (40 X 25 X 200)
3 X 1.5 X 8 (80 X 40 X 200)3 X 2 X 8 (80 X 50 X 200)
4 X 3 X 8 (100 X 80 X 200)
2 X 1 X 10 (50 X 25 X 250)3 X 1.5 X 10 (80 X 40 X 250)3 X 2 X 10 (80 X 50 X 250)
4 X 3 X 10 (100 X 80 X 250)6 X 4 X 10 (150 X 100 X 250)
3 X 1.5 X 13 (80 X 40 X 330)3 X 2 13 (80 X 50 X 330)
4 X 3 X 13 (100 X 80 X 330)6 X 4 X 13 (150 X 100 X 330)
8 X 6 X 15 (200 X 150 X 380)10 X 8 X 15 (250 X 200 X 380)
Nema
143T - 184T213T-256T
284TS - 326TS
143T - 184T213T - 215T254T - 286T
324TS - 365T404T - 405TS405T - 449TS
284T - 286T324T - 405T444T - 449T
IEC
80M - 90L132M - 160L180M - 180L
100L - 132M160M 180L
200L225S - 225M
250M280S 280M
180L200L - 250M280S - 315L
DimensionDesignation
AAABAA
A50A60A70
A05A50A60A70A80
A20A30A40A80
A110A120
BaseplateNumber
139148153
245252258264268280
368380398
Motor Frame RangePump Dimensions
CP
17.5 (445)17.5 (445)17.5 (445)
23.5 (597)23.5 (597)23.5 (597)
23.5 (597)23.5 (597)23.5 (597)23.5 (597)23.5 (597)
23.5 (597)23.5 (597)23.5 (597)23.5 (597)
33.875 (860)33.875 (860)
D
5.25 (133)5.25 (133)5.25 (133)
8.25 (210)8.25 (210)8.25 (210)
8.25 (210)8.25 (210)8.25 (210)8.25 (210)10 (254)
10 (254)10 (254)10 (254)10 (254)
14.5 (368)14.5 (368)
X
6.5 (165)6.5 (165)6.5 (165)
8.5 (216)9.5 (242)11 (280)
8.5 (216)8.5 (216)9.5 (242)11 (280)
13.5 (343)
10.5 (266)11.5 (292)12.5 (318)13.5 (343)
18 (457)19 (483)
Y
4 (102)4 (102)4 (102)
4 (102)4 (102)4 (102)
4 (102)4 (102)4 (102)4 (102)4 (102)
4 (102)4 (102)4 (102)4 (102)
6 (152)6 (152)
General Installation Recommendations
Choosing Pump LocationLocate the pump as close to theliquid source as practical so thesuction pipe is short and direct with a minimum of elbows, fittings and valves.Place the pump in a location so theunit is accessible for inspectionduring operation as well as formaintenance operations involvingremoval and disassembly.FoundationThe foundation should be strongenough to absorb any vibration andto form a permanent support for thebaseplate. This is important inmaintaining the alignment of thedirect connected unit. Foundationbolts of the proper size should beembedded in the concrete locatedby the outline drawing.AlignmentThe pump and motor are aligned atthe factory before shipment.However, realignment is necessary
after the complete unit has beeninstalled. Guidelines for checkingand aligning the pump componentsmay be found in the HydraulicInstitute Standards.PipingBoth suction and discharge pipesshould be supported independentlynear the pump so when the flangebolts are tightened no strain will betransmitted to the casing.A check valve should be beinstalled in the discharge line toprevent fluid from flowing backthrough the pump while it is shutdown. Gate valves should beinstalled in both discharge andsuction lines to isolate the pumpduring maintenance.Care must be taken in sizing andlocating suction piping to preventcavitation.Ordering InformationWilfley pumps are engineered tooperate in compliance with your
14
15 (381)18 (457)21 (533)
15 (381)18 (457)21 (533)21 (533)26 (660)26 (660)
26 (660)26 (660)26 (660)
HB
39 (991)48 (1219)53 (1346)
45 (1143)52 (1321)58 (1473)64 (1626)68 (1727)80 (2032)
68 (1727)80 (2032)98 (2489)
HE
4.5 (114)6 (152)
7.5 (191)
4.5 (114)6 (152)
7.5 (191)7.5 (191)9.5 (241)9.5 (241)
9.5 (241)9.5 (241)9.5 (241)
HF
36.5 (927)45.5 (1156)50.5 (1283)
42.5 (1080)49.5 (1257)55.5 (1410)61.5 (1562)65.5 (1664)77.5 (1969)
65.5 (1664)77.5 (1969)95.5 (2426)
3.75 (95)4.13 (105)4.75 (121)
3.75 (95)4.13 (105)4.75 (121)4.75 (121)4.75 (121)4.75 (121)
4.75 (121)4.75 (121)4.75 (121)
HH
.75 (19)
.75 (19)
.75 (19)
.75 (19)
.75 (19)1.00 (25)1.00 (25)1.00 (25)1.00 (25)
1.00 (25)1.00 (25)1.00 (25)
HL
4.5 (114)4.5 (114)4.5 (114)
4.5 (114)4.5 (114)4.5 (114)4.5 (114)4.5 (114)4.5 (114)
6.5 (165)6.5 (165)6.5 (165)
HP
1.25 (32)1.25 (32)1.25 (32)
1.25 (32)1.25 (32)1.25 (32)1.25 (32)1.25 (32)1.25 (32)
1.25 (32)1.25 (32)1.25 (32)
9 (229)10.5 (267)
12.88 (327)
12 (305)12.38 (314)
13 (330)13.88 (353)14.88 (378)15.88 (403)
19.25 (489)19.25 (489)19.25 (489)
13.75 (349)14.13 (359)14.75 (375)14.75 (375)14.88 (378)15.88 (403)
HD
Frame 2 Frame 3(and 6x4x10)
specifications. Careful evaluation ofpumping conditions is needed toprovide accurate pumprecommendations and quotations.This list will help establish specificpumping system conditions.• Liquid• Temperature• Static Head• Discharge Pipe Size• Length, Discharge Pipe• Discharge Pipe Fittings• Equivalent Length Discharge Pipe• Total Head• Maximum Suction Pressure• Minimum Suction Pressure• Capacity• Specific Gravity• % Solids by Weight• Mesh Analysis• Viscosity• NPSH Available
HA(MAX)
HG(MAX)
A7T11-FK
A.R. Wilfley & Sons, Inc.
P.O. Box 2330
Denver, Colorado 80201
303/779-1777
1-800-525-9930
FAX 303/779-1277
www.wilfley.com