ISO 9001:2008 REGISTERED COMPANY
Engineered Pumps forIndustrial andMunicipal Services
ASME END SUCTION PUMPSCatalogue K-90ASME B73.1-2012
ASME B73.1 / ANSI END SUCTION PUMPSThis catalogue provides the information you need to select a Smart Turner ASME B73.1 Pump to fit your specific needs. The ASME End Suction Pump range continues the Smart Turner tradition of providing well proven, uncomplicated designs incorporating high efficiency and smooth, low NPSH performance in a compact economical, Heavy Duty End Suction Pump.
Smart Turner ASME Pumps are ideally suited to plant service and chemical process applications where continuous, reliable operation is essential, whether the fluid is clean, dirty, corrosive or abrasive.
Smart Turner ASME Pumps are quality built for rugged, trouble free operation. They are available with either grease or oil lubricated bearings as standard.
Smart Turner ASME Pumps are engineered to exceed ANSI standards in all essential features. Impeller adjustment is positive and uncomplicated. High shaft stiffness yields low shaft deflections. Oversize bearings provide more than 2 year L10 life in all cases. The large stuffing box and the rear impeller pump out vanes provide excellent heat dissipation and low stuffing box pressure for long packing and seal life. The recessed pump out vane arrangement minimizes the effects of wear by maintain-ing pump out efficiency throughout the full range of impeller adjustment.
Smart Turner ASME Pumps are produced and stocked in a wide range of sizes using only three bearing housings. This makes an efficient parts inventory possible through extensive interchangeability of parts between pumps.
With the inclusion of ASME Pumps, Smart Turner can now offer a range of End Suction Pumps, totaling over 60 models, with capacities to 6000 USGPM, heads to 800 feet and speeds to 3500 Rpm.
This catalogue features ASME Chemical Process Pumps. For other EndSuction models, see catalogues B-90, D-90, F-90 and G-90.
SMART TURNER SOLUTION TO PUMPING PROBLEMSWhatever fluids you pump, Smart Turner has the background and technology to help you meet your needs effectively and efficiently with quality designed and built pumps. Smart Turner has established an enviable reputation for reliability while pumping chemicals, oil, beverages, slurries or sewage….almost any liquid known to man.
For over 100 years, Smart Turner has been dealing with and solving pumping problems throughout the world. This in-depth experience, coupled with modern computer tech-nology at every level from concept to shipping, is available to you through our sales and engineering personnel, coast to coast.
At Smart Turner, pumps are our only business, designed through experience to provide consistent performance and minimum maintenance. A wide range of sizes and types al-lows us to match the right pump to your specific application.
For further information, or an evaluation or your pumping system requirements, contact your nearest Smart Turner sales office or distributor as listed on the back cover of this catalogue.
2.
CONSTRUCTION MATERIALS• All Iron
• 316 Stainless Steel
• Steel
• Alloy 20
• CD4MCuN
• Hastelloy C
• Bronze
• Monel
• Other Materials on Application
3.
PAGE INDEX
PAGE
SPECIFICATION ................................................................................ K-2.0
DIMENSIONS
Bare Pump ........................................................................................ K-3.0
Pump, Base and Motor ................................................................ K-3.1
PARTS
#1 Frame Grease Lube ................................................................. K-4.0
#1 Frame Oil Lube ......................................................................... K-4.1
#2 / #3 Frame Grease Lube ......................................................... K-4.2
#2 / #3 Frame Oil Lube ................................................................. K-4.3
Seal Arrangements ....................................................................... K-4.4
Gland Arrangements .................................................................... K-4.5
MATERIAL LIST ................................................................................ K-5.0
PUMP DATA ....................................................................................... K-6.0
RANGE CHARTS ............................................................................... K-7.0
PHOTOS .............................................................................................. K-8.0
4.
DESIGN AND CONSTRUCTION FEATURES:Pump: Back pullout construction to ASME B73.1 / ANSI dimensional standards. Top center line to discharge and casing feet ensure maxi-mum rigidity and stability, while Smart Turner quality and precision ensure accurate fits and clearances.
Casing: A radially split cast volute with integral suction cover, rug-gedly designed with generous allowance for abrasion and corrosion. 150# ANSI flat faced flanged connections are standard. 300# flat faced flanges or RF are an option.
Impeller: Cast in one piece, the fully open impeller is trimmed to the exact diameter required and is factory balanced. The heavy section of the impeller provides excellent wear and corrosion allowance and the partial rear shroud provides maximum support for the blades. Rear pump out vanes provide axial hydraulic balance and low, but normally positive, stuffing box pressure. The pump out vanes are re-cessed into the stuffing box cover to maintain pump out efficiency if axial adjustment is made.
Stuffing Box Cover: A heavy one piece casting with rabbeted fit to the casing for positive alignment. The deep bore will accept a wide range of packing or mechanical seals. Optional Tapered and Big Bore stuffing boxing are available.
Gland: Split for packed stuffing boxes and solid for mechanical seals, the gland can be provided in a variety of arrangements to suit the application.
Gaskets: All gaskets are fully contained.
Shaft: Precision machined high quality alloy, normally fitted with a renewable sleeve, and oversized to minimize deflection to ensure smooth operation and maximize packing or seal life. Hardened Shafts are available as an option.
Sleeve: A precision machined, stainless steel, hook sleeve with an O-Ring seal against the impeller. A solid shaft without sleeve can be provided. Hardened Sleeves are available as an option.
Bearings: Antifriction bearings are generously sized for longer life, with a double row thrust bearing for minimum end play. Grease or oil lubricated arrangements are available. Grease is recommended for most services as being simpler and more reliable. Bearings are pro-tected by seals at both ends of the housing.
Bearing Housing: A rigid casting with precisely machined bores and rabbet fit to the adaptor to ensure concentricity and alignment with the stuffing box cover, casing and rotating element. The smaller housing has an integral foot and integral adaptor.
Adaptor: A rigid casting with integral gland drip reservoir, precision machined to ensure rigid and consistent alignment between bearing housing and liquid end.
Interchangeability: All pumps utilize one of only three bearing housings. Pumps with the same bearing housing have fully inter-changeable shafts, sleeves bearings, packing, seals, glands, and hard-ware resulting in an efficient parts inventory at both the factory and the customer.
Tests: All pumps are hydrostatically tested to 50 PSI above the maxi-mum casing design pressure. Performance Testing is available as an option OPTIONAL EQUIPMENT: Base: A rigid channel or fabricated base can be provided to our stan-dard for electric motor drives. Special bases can be provided and can incorporate grout holes, drip rims and other features.
Guard: A coupling guard to our standard can be mounted on the base plate. Special guards can be accommodated.
Flexible Coupling: For normal duty our current standard is provided when a coupling is ordered. However, couplings of almost any style or manufacturer can be accommodated.
Motors: An electric motor or other driver can be provided.
Cooler: A cooling coil can be fitted to oil lubricated bearing hous-ings for operation at elevated temperatures. No cooling is required for liquid temperatures below 350°F (177°C). Note; standard grease lubrication is good to liquid temperatures of at least 250°F (120°C). OTHER END SUCTION PUMPSOther Single Stage End Suction Pumps, End Suction design Two Stage Pumps, Non Clog Pumps, and Refuse Pumps are also available.
K-2.0
5.
K-3.
0
DIMENSIONS ANSI END SUCTION BARE PUMP
PAGE K-3.0
PUMP
MODEL
FRAME #
150# ANSI FF
PUMP DIMENSIONS
SUCT
DISCH
CP
D
E1
E2
F
H
O
U
V
X
Y
KEYWAY
1.5x1x6 1 1.5 1 17.5 5.25 3 0 7.25 0.625 11.75 0.875 2.125 6.5 4 3/16 x 3/32 3x1.5x6 1 3 1.5 17.5 5.25 3 0 7.25 0.625 11.75 0.875 2.125 6.5 4 3/16 x 3/32 1.5x1x8 1 1.5 1 17.5 5.25 3 0 7.25 0.625 11.75 0.875 2.125 6.5 4 3/16 x 3/32
3x2x6 2 3 2 23.5 8.25 4.875 3.625 12.5 0.625 16.5 1.125 2.75 8.25 4 1/4 x 1/8
3x1.5x8 2 3 1.5 23.5 8.25 4.875 3.625 12.5 0.625 16.75 1.125 2.75 8.5 4 1/4 x 1/8 3x2x8 2 3 2 23.5 8.25 4.875 3.625 12.5 0.625 17.75 1.125 2.75 9.5 4 1/4 x 1/8 4x3x8 2 4 3 23.5 8.25 4.875 3.625 12.5 0.625 19.25 1.125 2.75 11 4 1/4 x 1/8
2x1x10 2 2 1 23.5 8.25 4.875 3.625 12.5 0.625 16.75 1.125 2.75 8.5 4 1/4 x 1/8
3x1.5x10 2 3 1.5 23.5 8.25 4.875 3.625 12.5 0.625 16.75 1.125 2.75 8.5 4 1/4 x 1/8 3x2x10 2 3 2 23.5 8.25 4.875 3.625 12.5 0.625 17.75 1.125 2.75 9.5 4 1/4 x 1/8 4x3x10 2 4 3 23.5 8.25 4.875 3.625 12.5 0.625 19.25 1.125 2.75 11 4 1/4 x 1/8
3x1.5x13 2 3 1.5 23.5 10 4.875 3.625 12.5 0.625 20.5 1.125 2.75 10.5 4 1/4 x 1/8 3x2x13 2 3 2 23.5 10 4.875 3.625 12.5 0.625 21.5 1.125 2.75 11.5 4 1/4 x 1/8 4x3x13 2 4 3 23.5 10 4.875 3.625 12.5 0.625 22.5 1.125 2.75 12.5 4 1/4 x 1/8 6x4x13 2 6 4 23.5 10 4.875 3.625 12.5 0.625 23.5 1.125 2.75 13.5 4 1/4 x 1/8
8x6x13 3 8 6 33.875 14.5 8 4.5 18.75 0.75 30.5 2.375 3.75 16 6 5/8 x 5/16 10x8x13 3 10 8 33.875 14.5 8 4.5 18.75 0.75 32.5 2.375 3.75 18 6 5/8 x 5/16 8x6x15 3 8 6 33.875 14.5 8 4.5 18.75 0.75 32.5 2.375 3.75 18 6 5/8 x 5/16 10x8x15 3 10 8 33.875 14.5 8 4.5 18.75 0.75 33.5 2.375 3.75 19 6 5/8 x 5/16
These are not certified dimensions. Certified drawing can be obtained on request. All dimensions in inches.
DIMENSIONS ANSI END SUCTION BARE PUMP
PAGE K-3.0
PUMP
MODEL
FRAME #
150# ANSI FF
PUMP DIMENSIONS
SUCT
DISCH
CP
D
E1
E2
F
H
O
U
V
X
Y
KEYWAY
1.5x1x6 1 1.5 1 17.5 5.25 3 0 7.25 0.625 11.75 0.875 2.125 6.5 4 3/16 x 3/32 3x1.5x6 1 3 1.5 17.5 5.25 3 0 7.25 0.625 11.75 0.875 2.125 6.5 4 3/16 x 3/32 1.5x1x8 1 1.5 1 17.5 5.25 3 0 7.25 0.625 11.75 0.875 2.125 6.5 4 3/16 x 3/32
3x2x6 2 3 2 23.5 8.25 4.875 3.625 12.5 0.625 16.5 1.125 2.75 8.25 4 1/4 x 1/8
3x1.5x8 2 3 1.5 23.5 8.25 4.875 3.625 12.5 0.625 16.75 1.125 2.75 8.5 4 1/4 x 1/8 3x2x8 2 3 2 23.5 8.25 4.875 3.625 12.5 0.625 17.75 1.125 2.75 9.5 4 1/4 x 1/8 4x3x8 2 4 3 23.5 8.25 4.875 3.625 12.5 0.625 19.25 1.125 2.75 11 4 1/4 x 1/8
2x1x10 2 2 1 23.5 8.25 4.875 3.625 12.5 0.625 16.75 1.125 2.75 8.5 4 1/4 x 1/8
3x1.5x10 2 3 1.5 23.5 8.25 4.875 3.625 12.5 0.625 16.75 1.125 2.75 8.5 4 1/4 x 1/8 3x2x10 2 3 2 23.5 8.25 4.875 3.625 12.5 0.625 17.75 1.125 2.75 9.5 4 1/4 x 1/8 4x3x10 2 4 3 23.5 8.25 4.875 3.625 12.5 0.625 19.25 1.125 2.75 11 4 1/4 x 1/8
3x1.5x13 2 3 1.5 23.5 10 4.875 3.625 12.5 0.625 20.5 1.125 2.75 10.5 4 1/4 x 1/8 3x2x13 2 3 2 23.5 10 4.875 3.625 12.5 0.625 21.5 1.125 2.75 11.5 4 1/4 x 1/8 4x3x13 2 4 3 23.5 10 4.875 3.625 12.5 0.625 22.5 1.125 2.75 12.5 4 1/4 x 1/8 6x4x13 2 6 4 23.5 10 4.875 3.625 12.5 0.625 23.5 1.125 2.75 13.5 4 1/4 x 1/8
8x6x13 3 8 6 33.875 14.5 8 4.5 18.75 0.75 30.5 2.375 3.75 16 6 5/8 x 5/16 10x8x13 3 10 8 33.875 14.5 8 4.5 18.75 0.75 32.5 2.375 3.75 18 6 5/8 x 5/16 8x6x15 3 8 6 33.875 14.5 8 4.5 18.75 0.75 32.5 2.375 3.75 18 6 5/8 x 5/16 10x8x15 3 10 8 33.875 14.5 8 4.5 18.75 0.75 33.5 2.375 3.75 19 6 5/8 x 5/16
These are not certified dimensions. Certified drawing can be obtained on request. All dimensions in inches.
D I M E N S I O N SASME B73.1 / ANSI END SUCTION BARE PUMP
K3.0 Table
150# ANSI FF
PUMP DIMENSIONS
PUMP
MODEL
FRAME #
SUCT
DISCH
CP
D
E1
E2
F
H
O
U
V
X
Y
KEYWAY
1.5x1x6 1 1.5 1 17.5 5.25 3 0 7.25 0.625 11.75 0.875 2.125 6.5 4 3/16 x 3/32 3x1.5x6 1 3 1.5 17.5 5.25 3 0 7.25 0.625 11.75 0.875 2.125 6.5 4 3/16 x 3/32 1.5x1x8 1 1.5 1 17.5 5.25 3 0 7.25 0.625 11.75 0.875 2.125 6.5 4 3/16 x 3/32 3x2x6 2 3 2 23.5 8.25 4.875 3.625 12.5 0.625 16.5 1.125 2.75 8.25 4 1/4 x 1/8
3x1.5x8 2 3 1.5 23.5 8.25 4.875 3.625 12.5 0.625 16.75 1.125 2.75 8.5 4 1/4 x 1/8 3x2x8 2 3 2 23.5 8.25 4.875 3.625 12.5 0.625 17.75 1.125 2.75 9.5 4 1/4 x 1/8 4x3x8 2 4 3 23.5 8.25 4.875 3.625 12.5 0.625 19.25 1.125 2.75 11 4 1/4 x 1/8 2x1x10 2 2 1 23.5 8.25 4.875 3.625 12.5 0.625 16.75 1.125 2.75 8.5 4 1/4 x 1/8
3x1.5x10 2 3 1.5 23.5 8.25 4.875 3.625 12.5 0.625 16.75 1.125 2.75 8.5 4 1/4 x 1/8 3x2x10 2 3 2 23.5 8.25 4.875 3.625 12.5 0.625 17.75 1.125 2.75 9.5 4 1/4 x 1/8 4x3x10 2 4 3 23.5 8.25 4.875 3.625 12.5 0.625 19.25 1.125 2.75 11 4 1/4 x 1/8
3x1.5x13 2 3 1.5 23.5 10 4.875 3.625 12.5 0.625 20.5 1.125 2.75 10.5 4 1/4 x 1/8 3x2x13 2 3 2 23.5 10 4.875 3.625 12.5 0.625 21.5 1.125 2.75 11.5 4 1/4 x 1/8 4x3x13 2 4 3 23.5 10 4.875 3.625 12.5 0.625 22.5 1.125 2.75 12.5 4 1/4 x 1/8 6x4x13 2 6 4 23.5 10 4.875 3.625 12.5 0.625 23.5 1.125 2.75 13.5 4 1/4 x 1/8 8x6x13 3 8 6 33.875 14.5 8 4.5 18.75 0.875 30.5 2.375 3.75 16 6 5/8 x 5/16
10x8x13 3 10 8 33.875 14.5 8 4.5 18.75 0.875 32.5 2.375 3.75 18 6 5/8 x 5/16 8x6x15 3 8 6 33.875 14.5 8 4.5 18.75 0.875 32.5 2.375 3.75 18 6 5/8 x 5/16
10x8x15 3 10 8 33.875 14.5 8 4.5 18.75 0.875 33.5 2.375 3.75 19 6 5/8 x 5/16 8x6x17 3 8 6 33.875 14.5 8 4.5 18.75 0.875 32.5 2.375 3.75 18 6 5/8 x 5/16
10x8x17 3 10 8 33.875 14.5 8 4.5 18.75 0.875 33.5 2.375 3.75 19 6 5/8 x 5/16
6.
K-3.1
D I M E N S I O N SASME B73.1 / ANSI END SUCTION PUMP, BASE & MOTOR
DIMENSIONS ANSI END SUCTION PUMP, BASE & MOTOR
PAGE K-3.1
MOTOR DIMENSIONS
FRAME
C
M
56 13 3.5 143T 13 3.5 145T 14 3.5 182T 15 4.5 184T 16 4.5 213T 18 5 215T 20 5 254T 24 6 256T 26 6 284T 27 7
284TS 25 7 286T 28 7
286TS 26 7 324T 33 8
324TS 32 8 326T 34 8
326TS 33 8 354T 37 9
364TS 35 9 365T 39 9
365TS 37 9 404T 42 10
404TS 39 10 405T 44 10
405TS 41 10 444T 47 11
444TS 44 11 445T 50 11
445TS 46 11 447T 50 11
447TS
46
11
PUMP
MODEL
FRAME
#
125/150# ANSI FF
PUMP DIMENSIONS
BASE PER MOTOR FRAME
SUCT
DISCH
CP
D
X
Y
56-184
213-215
254-256
284-286
324-365
404-405
444-449
1.5x1x6 1 1.5 1 17.5 5.25 6.5 4 1A 2A 2A 3x1.5x6 1 3 1.5 17.5 5.25 6.5 4 1A 2A 2A 1.5x1x8 1 1.5 1 17.5 5.25 6.5 4 1A 2A 2A 3x2x6 2 3 2 23.5 8.25 8.25 4 3A 4A 5A 5A 6A
3x1.5x8 2 3 1.5 23.5 8.25 8.5 4 3A 4A 5A 5A 6A 3x2x8 2 3 2 23.5 8.25 9.5 4 3A 4A 5A 5A 6A 4x3x8 2 4 3 23.5 8.25 11 4 3A 4A 5A 5A 6A 7A 2x1x10 2 2 1 23.5 8.25 8.5 4 3A 4A 5A 5A 6A 7A
3x1.5x10 2 3 1.5 23.5 8.25 8.5 4 3A 4A 5A 5A 6A 7A 3x2x10 2 3 2 23.5 8.25 9.5 4 3A 4A 5A 5A 6A 7A 4x3x10 2 4 3 23.5 8.25 11 4 3A 4A 5A 5A 6A 7A
3x1.5x13 2 3 1.5 23.5 10 10.5 4 3B 4B 5B 5B 6B 7A 3x2x13 2 3 2 23.5 10 11.5 4 3B 4B 5B 5B 6B 7A 4x3x13 2 4 3 23.5 10 12.5 4 3B 4B 5B 5B 6B 7A 6x4x13 2 6 4 23.5 10 13.5 4 3B 4B 5B 5B 6B 7A 8x6x13 3 8 6 33.875 14.5 16 6 5C 5C 6C 7B 8A 8x6x15 3 8 6 33.875 14.5 18 6 5C 5C 6C 7B 8A
10x8x13 3 10 8 33.875 14.5 18 6 5C 5C 6C 7B 8A 10x8x15 3 10 8 33.875 14.5 19 6 5C 5C 6C 7B 8A
BASE PLATE
BASE DIMENSIONS
HA
HB
HD
HE
HF
HG
HH
HL
HP
HT
1A 12 39 9 4.5 36.5 3 0.75 4.5 1.25 3.5 2A 15 48 10.5 6 45.5 3.375 0.75 4.5 1.25 3.5 3A 12 45 12 4.5 42.5 3 0.75 4.5 1.25 3.5 3B 12 45 13.75 4.5 42.5 3 0.75 4.5 1.25 3.5 4A 15 52 12.375 6 49.5 3.375 0.75 4.5 1.25 3.5 4B 15 52 14.125 6 49.5 3.375 0.75 4.5 1.25 3.5 5A 18 58 13 7.5 55.5 3.9375 1 4.5 1.25 3.5 5B 18 58 14.75 7.5 55.5 3.9375 1 4.5 1.25 3.5 5C 24 68 19.25 9.5 65.5 4 1 6.5 1.25 5 6A 18 64 13.875 7.5 61.5 3.9375 1 4.5 1.25 3.5 6B 18 64 14.75 7.5 61.5 3.9375 1 4.5 1.25 3.5 6C 24 80 19.25 7.5 77.5 4 1 6.5 1.25 5 7A 24 68 14.875 9.5 65.5 4 1 4.5 1.25 4.75 7B 24 80 19.25 9.5 77.5 4 1 6.5 1.25 5 8A 24 98 19.25 9.5 95.5 4 1 6.5 1.25 5
These are not certified dimensions. Certified drawing can be obtained on request. All dimensions in inches. Motor dimensions are typical.
These are not certified dimensions. Certified drawings can be obtained on request. All dimensions in inches. Motor dimensions are typical.
K3.1 Table
125/150# ANSI FF
PUMP DIMENSIONS
BASE PER MOTOR FRAME
PUMP
MODEL
FRAME
#
SUCT
DISCH
CP
D
X
Y
56-184 213-215
254-256
284-286
324-365
404-405
444-449
1.5x1x6 1 1.5 1 17.5 5.25 6.5 4 1A 2A 2A 3x1.5x6 1 3 1.5 17.5 5.25 6.5 4 1A 2A 2A 1.5x1x8 1 1.5 1 17.5 5.25 6.5 4 1A 2A 2A 3x2x6 2 3 2 23.5 8.25 8.25 4 3A 4A 5A 5A 6A
3x1.5x8 2 3 1.5 23.5 8.25 8.5 4 3A 4A 5A 5A 6A 3x2x8 2 3 2 23.5 8.25 9.5 4 3A 4A 5A 5A 6A 4x3x8 2 4 3 23.5 8.25 11 4 3A 4A 5A 5A 6A 7A
2x1x10 2 2 1 23.5 8.25 8.5 4 3A 4A 5A 5A 6A 7A 3x1.5x10 2 3 1.5 23.5 8.25 8.5 4 3A 4A 5A 5A 6A 7A 3x2x10 2 3 2 23.5 8.25 9.5 4 3A 4A 5A 5A 6A 7A 4x3x10 2 4 3 23.5 8.25 11 4 3A 4A 5A 5A 6A 7A 6x4x10 2 6 4 23.5 10 12.5 4 3B 4B 5B 5B 6B 7A
3x1.5x13 2 3 1.5 23.5 10 10.5 4 3B 4B 5B 5B 6B 7A 3x2x13 2 3 2 23.5 10 11.5 4 3B 4B 5B 5B 6B 7A 4x3x13 2 4 3 23.5 10 12.5 4 3B 4B 5B 5B 6B 7A 6x4x13 2 6 4 23.5 10 13.5 4 3B 4B 5B 5B 6B 7A 8x6x13 3 8 6 33.875 14.5 16 6 5C 5C 6C 7B 8A 10x8x13 3 10 8 33.875 14.5 18 6 5C 5C 6C 7B 8A 8x6x15 3 8 6 33.875 14.5 18 6 5C 5C 6C 7B 8A 10x8x15 3 10 8 33.875 14.5 19 6 5C 5C 6C 7B 8A 8x6x17 3 8 6 33.875 14.5 18 6 5C 5C 6C 7B 8A 10x8x17 3 10 8 33.875 14.5 19 6 5C 5C 6C 7B 8A
DIMENSIONS ANSI END SUCTION PUMP, BASE & MOTOR
PAGE K-3.1
MOTOR DIMENSIONS
FRAME
C
M
56 13 3.5 143T 13 3.5 145T 14 3.5 182T 15 4.5 184T 16 4.5 213T 18 5 215T 20 5 254T 24 6 256T 26 6 284T 27 7
284TS 25 7 286T 28 7
286TS 26 7 324T 33 8
324TS 32 8 326T 34 8
326TS 33 8 354T 37 9
364TS 35 9 365T 39 9
365TS 37 9 404T 42 10
404TS 39 10 405T 44 10
405TS 41 10 444T 47 11
444TS 44 11 445T 50 11
445TS 46 11 447T 50 11
447TS
46
11
PUMP
MODEL
FRAME
#
125/150# ANSI FF
PUMP DIMENSIONS
BASE PER MOTOR FRAME
SUCT
DISCH
CP
D
X
Y
56-184
213-215
254-256
284-286
324-365
404-405
444-449
1.5x1x6 1 1.5 1 17.5 5.25 6.5 4 1A 2A 2A 3x1.5x6 1 3 1.5 17.5 5.25 6.5 4 1A 2A 2A 1.5x1x8 1 1.5 1 17.5 5.25 6.5 4 1A 2A 2A 3x2x6 2 3 2 23.5 8.25 8.25 4 3A 4A 5A 5A 6A
3x1.5x8 2 3 1.5 23.5 8.25 8.5 4 3A 4A 5A 5A 6A 3x2x8 2 3 2 23.5 8.25 9.5 4 3A 4A 5A 5A 6A 4x3x8 2 4 3 23.5 8.25 11 4 3A 4A 5A 5A 6A 7A 2x1x10 2 2 1 23.5 8.25 8.5 4 3A 4A 5A 5A 6A 7A
3x1.5x10 2 3 1.5 23.5 8.25 8.5 4 3A 4A 5A 5A 6A 7A 3x2x10 2 3 2 23.5 8.25 9.5 4 3A 4A 5A 5A 6A 7A 4x3x10 2 4 3 23.5 8.25 11 4 3A 4A 5A 5A 6A 7A
3x1.5x13 2 3 1.5 23.5 10 10.5 4 3B 4B 5B 5B 6B 7A 3x2x13 2 3 2 23.5 10 11.5 4 3B 4B 5B 5B 6B 7A 4x3x13 2 4 3 23.5 10 12.5 4 3B 4B 5B 5B 6B 7A 6x4x13 2 6 4 23.5 10 13.5 4 3B 4B 5B 5B 6B 7A 8x6x13 3 8 6 33.875 14.5 16 6 5C 5C 6C 7B 8A 8x6x15 3 8 6 33.875 14.5 18 6 5C 5C 6C 7B 8A
10x8x13 3 10 8 33.875 14.5 18 6 5C 5C 6C 7B 8A 10x8x15 3 10 8 33.875 14.5 19 6 5C 5C 6C 7B 8A
BASE PLATE
BASE DIMENSIONS
HA
HB
HD
HE
HF
HG
HH
HL
HP
HT
1A 12 39 9 4.5 36.5 3 0.75 4.5 1.25 3.5 2A 15 48 10.5 6 45.5 3.375 0.75 4.5 1.25 3.5 3A 12 45 12 4.5 42.5 3 0.75 4.5 1.25 3.5 3B 12 45 13.75 4.5 42.5 3 0.75 4.5 1.25 3.5 4A 15 52 12.375 6 49.5 3.375 0.75 4.5 1.25 3.5 4B 15 52 14.125 6 49.5 3.375 0.75 4.5 1.25 3.5 5A 18 58 13 7.5 55.5 3.9375 1 4.5 1.25 3.5 5B 18 58 14.75 7.5 55.5 3.9375 1 4.5 1.25 3.5 5C 24 68 19.25 9.5 65.5 4 1 6.5 1.25 5 6A 18 64 13.875 7.5 61.5 3.9375 1 4.5 1.25 3.5 6B 18 64 14.75 7.5 61.5 3.9375 1 4.5 1.25 3.5 6C 24 80 19.25 7.5 77.5 4 1 6.5 1.25 5 7A 24 68 14.875 9.5 65.5 4 1 4.5 1.25 4.75 7B 24 80 19.25 9.5 77.5 4 1 6.5 1.25 5 8A 24 98 19.25 9.5 95.5 4 1 6.5 1.25 5
These are not certified dimensions. Certified drawing can be obtained on request. All dimensions in inches. Motor dimensions are typical.
7.
K-4.
0
P A R T SASME B73.1 / ANSI END SUCTION #1 FRAME GREASE LUBE
PARTS ANSI END SUCTION #1 FRAME GREASE LUBE
PAGE K-4.0
PART NO. DESCRIPTION PART NO. DESCRIPTION 100 Casing 162 Locknut, Outboard Bearing 101 Stuffing Box Cover 164A Seal, Outboard Bearing 103 Impeller, Open 164B Seal, Inboard Bearing 105 Bearing Cover, Outboard 165A Grease Fitting, Outboard Bearing 106 Split Gland (Packing) 165B Grease Fitting, Inboard Bearing 108 Bearing Housing 170A Pipe Plug, Bearing Housing 116 Bearing Cartridge 170B Pipe Plug, Stuffing Box 117 Flinger 170C Pipe Plug, Bearing Housing Drain 124 Shaft Sleeve 176 Packing 128 Shaft 179 Gland Nut
142A Bearing, Outboard (Thrust) 180A Capscrew, Bearing Cover 142B Bearing, inboard (Radial) 180B Capscrew, Gland 146A Lockwasher, Bearing 180C Capscrew, Bearing Housing to Casing 149 Stud, Gland 181 Allen Set Screw, Bearing Cover 150 Key, Coupling 191A Gasket, Casing
153A Flat Washer, Gland 401A O-Ring, Bearing Cartridge 155 Retaining Ring, Inboard Bearing 401C O-Ring, Shaft Sleeve
Refer to pages K-4.4 and K-4.5 for optional stuffing box, seal and gland arrangements.
8.
K-4.1
P A R T SASME B73.1 / ANSI END SUCTION #1 FRAME OIL LUBE
PARTS ANSI END SUCTION #1 FRAME OIL LUBE
PAGE K-4.1
PART NO. DESCRIPTION PART NO. DESCRIPTION 100 Casing 164A Seal, Outboard Bearing 101 Stuffing Box Cover 164B Seal, Inboard Bearing 103 Impeller, Open 165A Site Glass / Bottle Oiler 105 Bearing Cover, Outboard 165B Breather / Vent 106 Split Gland (Packing) 170A Pipe Plug, Bearing Housing 108 Bearing Housing 170B Pipe Plug, Stuffing Box 116 Bearing Cartridge 170C Pipe Plug, Bearing Housing Drain 117 Flinger 176 Packing 124 Shaft Sleeve 179 Hex Nut, Gland 128 Shaft 180A Capscrew, Bearing Cover
142A Bearing, Outboard (Thrust) 180B Capscrew, Gland 142B Bearing, inboard (Radial) 180C Capscrew, Bearing Housing to Casing 146A Lockwasher, Bearing 180D Capscrew, Gland Halves 149 Stud, Gland 181 Allen Set Screw, Bearing Cover 150 Key, Coupling 191A Gasket, Casing
153A Flat Washer, Gland 401A O-Ring, Bearing Cartridge 155 Retaining Ring, Inboard Bearing 401C O-Ring, Shaft Sleeve 162 Locknut, Outboard Bearing
Refer to pages K-4.4 and K-4.5 for optional stuffing box, seal and gland arrangements.
9.
K-4.
2
P A R T SASME B73.1 / ANSI END SUCTION #2/3 FRAME GREASE LUBE
PARTS ANSI END SUCTION #2/3 FRAME GREASE LUBE
PAGE K-4.2
PART NO. DESCRIPTION PART NO. DESCRIPTION 100 Casing 162 Locknut, Outboard Bearing 101 Stuffing Box Cover 163 Mechanical Seal 103 Impeller, Open 164A Seal, Outboard Bearing 104 Adaptor 164B Seal, Inboard Bearing 105 Bearing Cover, Outboard 165A Grease Fitting, Outboard Bearing 107 Gland (Mechanical Seal) 165B Grease Fitting, Inboard Bearing 108 Bearing Housing 170A Pipe Plug, Bearing Housing 116 Bearing Cartridge 170B Pipe Plug, Stuffing Box 117 Flinger 170C Pipe Plug, Bearing Housing Drain 124 Shaft Sleeve 180A Capscrew, Bearing Cover
142A Bearing, Outboard (Thrust) 180B Capscrew, Gland 142B Bearing, inboard (Radial) 180C Capscrew, Bearing Housing to Adaptor 146A Lockwasher, Bearing 180D Capscrew, Adaptor to Stuffing Box 149 Stud, Gland 180E Capscrew, Adaptor to Casing 150 Key, Coupling 181 Allen Set Screw, Bearing Cover
153A Flat Washer, Gland 191A Gasket, Casing 153B Flat Washer, Foot 401A O-Ring, Bearing Cartridge 155 Retaining Ring, Inboard Bearing 401B O-Ring, Adaptor to Bearing Frame 157 Frame Support 401C O-Ring, Shaft Sleeve 160 Eyebolt
Refer to pages K-4.4 and K-4.5 for optional stuffing box, seal and gland arrangements.
10.
K-4.3
P A R T SASME B73.1 / ANSI END SUCTION #2/3 FRAME OIL LUBE
PARTS ANSI END SUCTION #2/3 FRAME OIL LUBE
PAGE K-4.3
PART NO. DESCRIPTION PART NO. DESCRIPTION 100 Casing 164A Seal, Outboard Bearing 101 Stuffing Box Cover 164B Seal, Inboard Bearing 103 Impeller, Open 165B Breather, Bearing Housing 104 Adaptor 165A Sight Gauge, Constant Level Oiler 105 Bearing Cover, Outboard 170A Pipe Plug, Bearing Housing 106 Split Gland (Packing) 170B Pipe Plug, Stuffing Box 108 Bearing Housing 170C Pipe Plug, Bearing Housing Drain 116 Bearing Cartridge 170D Pipe Plug, Bearing Cover 117 Flinger 176 Packing 124 Shaft Sleeve 179 Hex Nut, Gland 128 Shaft 179B Hex Nut, Gland Halves
142A Bearing, Outboard (Thrust) 180A Capscrew, Bearing Cover 142B Bearing, inboard (Radial) 180B Capscrew, Gland 146A Lockwasher, Bearing 180C Capscrew, Bearing Housing to Adaptor 149 Stud, Gland 180D Capscrew, Adaptor to Stuffing Box 150 Key, Coupling 180E Capscrew, Adaptor to Casing
153A Flat Washer, Gland 181 Allen Set Screw, Bearing Cover 153B Flat Washer, Foot 191A Gasket, Casing 155 Retaining Ring, Inboard Bearing 401A O-Ring, Bearing Cartridge 157 Frame Support 401B O-Ring, Adaptor to Bearing Frame 160 Eyebolt 401C O-Ring, Shaft Sleeve 162 Locknut, Outboard Bearing
Refer to pages K-4.4 and K-4.5 for optional stuffing box, seal and gland arrangements.
11.
K-4.
4
SEAL ARRANGEMENTSASME B73.1 / ANSI END SUCTION
12.
K-4.5
GLAND ARRANGEMENTSASME B73.1 / ANSI END SUCTION
13.
K-5.
0
MATERIAL LISTASME B73.1 / ANSI END SUCTION
MATERIAL LIST ANSI END SUCTION
PAGE K-5.0
PART NO. DESCRIPTION ALL IRON STAINLESS STEEL
100 101 103 104 105 106 107 108 117 124 127 133
142A 142B 144
146A 146B 149 150
153A 153B 155A 155B 155C 157 160
162A 163
164A 164B 165A 165B 170A 170B 176 179
180A 180B 180C 180D 180E 180G 191A 191B 401A 401B 401C
Casing Stuffing Box Cover Impeller Open Adaptor Outboard Bearing Cover Gland (Packing) Gland (Mechanical Seal) Bearing Housing Flinger Shaft Sleeve Lantern Ring Bearing Sleeve Outboard (Thrust) Bearing Inboard (Radial) Bearing Seal Retaining Ring Bearing Lockwasher Gland Lockwasher Gland Stud Coupling Key Gland Washer Washer (Foot) Outboard Bearing Seal (Outboard) Inboard Bearing Retaining Ring Neck Ring Foot Eyebolt Outboard Bearing Locknut Mechanical Seal Oil Seal (Outboard) Oil Seal (Inboard) Grease Fitting Bearing Housing Vent Bearing Housing Drain Plug Stuffing Box Plug Packing Gland Nut Capscrew (Bearing Housing-Foot) Capscrew (Bearing Housing-Adaptor) Capscrew (Gland) Capscrew (Adaptor-Stuffing Box) Capscrew (Adaptor-Casing) Capscrew (Mechanical Seal Gland) Gasket (Casing) Gasket (Seal Gland) O-Ring (Bearing Cover Outboard) O-Ring (Bearing Housing-Adaptor) O-Ring (Sleeve)
Ductile Iron Ductile Iron Ductile Iron Ductile Iron
Cast Iron Steel Steel
Cast Iron Rubber
316 Stainless Cast Iron Cast Iron
Steel Steel
316 Stainless Steel
304-316 Stainless 304-316 Stainless
Steel Steel Steel Buna Buna
Cast Iron Cast Iron
Steel Steel
As Per Application Buna Buna
Coated Steel Steel Steel Steel
As Per Application 304-316 Stainless
Steel Steel Steel Steel Steel
304-316 Stainless Aramid Fiber Aramid Fiber
Buna Buna Viton
316 Stainless 316 Stainless 316 Stainless Ductile Iron
Cast Iron 316 Stainless 316 Stainless
Cast Iron Rubber
316 Stainless Cast Iron Cast Iron
Steel Steel
316 Stainless Steel
304-316 Stainless 304-316 Stainless
Steel Steel Steel Buna Buna
Cast Iron Cast Iron
Steel Steel
As Per Application Buna Buna
Coated Steel Steel Steel Steel
As Per Application 304-316 Stainless
Steel Steel Steel
304-316 Stainless Steel
304-316 Stainless Aramid Fiber Aramid Fiber
Buna Buna
Viton / Teflon
MATERIAL SPECIFICATION FORM MATERIAL SPECIFICATION FORM Ductile Iron Steel
316 Stainless
ASTM A536 60-45-12
ASTM A27, A216 WCB ASTM A108 or A576
ASTM A743 CF8M ASTM A276
Castings
Casting Barstock
Castings Barstock
Alloy 20
CD4MCU
ASTM A743 CN7M ASTM B743
ASTM A890 1B
Castings Barstock
Castings
14.
K-6.0
PUMP DATAASME B73.1 / ANSI END SUCTION
PUMP DATA ANSI END SUCTION
PAGE-6.0
SHAFT BEARINGS STUFFING BOX CASING IMPELLER
1.5x1x6 3x1.5x6 1.5x1x8
3x2x6
3x1.5x8 3x2x8 4x3x8
2x1x10
3x1.5x10 3x2x10 4x3x10
3x1.5x13 3x2x13 4x3x13 6x4x13
8x6x13 8x6x15
10x8x13 10x8x15
1.5 x 1 3 x 1.5 1.5 x 1
3 x 2
3 x 1.5 3 x 2 4 x 3
2 x 1
3 x 1.5 3 x 2 4 x 3
3 x 1.5 3 x 2 4 x 3 6 x 4
8 x 6 8 x 6 10 x 8 10 x 8
MO
DE
L
CO
NN
EC
TIO
N S
IZE
FRA
ME
SIZ
E
DIA
. AT
CP
LG.
1 1 1
2 2 2 2 2 2 2 2 2 2 2 2 3 3 3 3
7/8 7/8 7/8
1-1/8 1-1/8 1-1/8 1-1/8
1-1/8 1-1/8 1-1/8 1-1/8
1-1/8 1-1/8 1-1/8 1-1/8
2-3/8 2-3/8 2-3/8 2-3/8
KE
YWA
Y
3/16 x 3/32 3/16 x 3/32 3/16 x 3/32
1/4 x 1/8 1/4 x 1/8 1/4 x 1/8 1/4 x 1/8
1/4 x 1/8 1/4 x 1/8 1/4 x 1/8 1/4 x 1/8
1/4 x 1/8 1/4 x 1/8 1/4 x 1/8 1/4 x 1/8
5/8 x 5/16 5/8 x 5/16 5/8 x 5/16 5/8 x 5/16
DIA
. BE
TWE
EN
BR
GS
.
DIS
TAN
CE
BE
TWE
EN
B
RG
. CE
NTE
RS
1-7/16 1-7/16 1-7/16
2-5/16 2-5/16 2-5/16 2-5/16
2-5/16 2-5/16 2-5/16 2-5/16
2-5/16 2-5/16 2-5/16 2-5/16
10-3/16 10-3/16 10-3/16 10-3/16
4-9/16 4-9/16 4-9/16
7 7 7 7
7 7 7 7
7 7 7 7
10-5/8 10-5/8 10-5/8 10-5/8
INB
OA
RD
BE
AR
ING
(R
AD
IAL)
6207 6207 6207
6310 6310 6310 6310
6310 6310 6310 6310
6310 6310 6310 6310
6314 6314 6314 6314
OU
TBO
AR
D B
EA
RIN
G
(TH
RU
ST)
5306 5306 5306
5310 5310 5310 5310
5310 5310 5310 5310
5310 5310 5310 5310
5314 5314 5314 5314
BO
RE
2-1/4 2-1/4 2-1/4
2-3/4 2-3/4 2-3/4 2-3/4
2-3/4 2-3/4 2-3/4 2-3/4
2-3/4 2-3/4 2-3/4 2-3/4
3-7/8 3-7/8 3-7/8 3-5/8
SLE
EV
E D
IA
1-3/8 1-3/8 1-3/8
1-3/4 1-3/4 1-3/4 1-3/4
1-3/4 1-3/4 1-3/4 1-3/4
1-3/4 1-3/4 1-3/4 1-3/4
2-3/4 2-3/4 2-3/4 2-3/4
PA
CK
ING
SIZ
E
7/16 7/16 7/16
1/2 1/2 1/2 1/2
1/2 1/2 1/2 1/2
1/2 1/2 1/2 1/2
9/16 9/16 9/16 9/16
DE
PTH
2-13/16 2-13/16 2-13/16
3-1/4 3-1/4 3-1/4 3-1/4
3-1/4 3-1/4 3-1/4 3-1/4
3-1/4 3-1/4 3-1/4 3-1/4
3-5/8 3-5/8 3-5/8 3-5/8
NO
M. T
HIC
KN
ES
S
7/16 7/16 7/16
1/2 1/2 1/2 1/2
1/2 1/2 1/2 1/2
9/16 9/16 9/16 9/16
9/16 9/16 9/16 9/16
DR
AIN
CO
NN
EC
TIO
NS
1/2 1/2 1/2
1/2 1/2 1/2 1/2
1/2 1/2 1/2 1/2
1/2 1/2 1/2 1/2
1/2 1/2 1/2 1/2
TES
T P
RE
SS
UR
E B
AS
ED
O
N C
OLD
WA
TER
(PS
I)
150 150 225
150 225 225 225
300 300 300 300
300 300 300 300
150 150 150 150
MA
X. I
MP
. DIA
.
6-3/8 6-3/8
8
6-1/4 8-3/4 8-3/4 8-3/4
10 10 10 10
13-1/4 13-1/4 13-1/4 13-1/4
13 15 13 15
M
IN. I
MP
. DIA
.
3-1/2 4 5
4 5
5-1/2 5-1/2
5 6 6 6
9 9 9 9
13 15 13 15
* 17” ASME B73.1 / ANSI Pumps not shown
15.
K-7.
0
RANGE CHARTSASME B73.1 / ANSI END SUCTION
RANGE CHARTS ANSI END SUCTION
PAGE-7.0
ALL MODELS
16.
K-8.0
PHOTOSASME B73.1 / ANSI END SUCTION
17.
K-8.
0
PHOTOSASME B73.1 / ANSI END SUCTION
PU
MPS
ASME B73.1-2012 Chemical Process PumpsSize to 10x8x17Capacity to 6000 USGPMHead to 800 ft.Speed to 3600 rpmMetallurgy Cast Iron,Alloys, Steel, Exotics
Double SuctionSize to 14x12x16
Capacity to 8000 USGPMHead to 750 ft.
Speed to 3600 rpmMetallurgy Cast Iron, Bronze
Multi-stage High Pressure Boiler FeedSize to 4x2x10Capacity to 400 USGPMHead to 800 ft.Speed to 3600 rpmMetallurgy Cast Iron, Bronze
End SuctionSize to 10x8x16
Capacity to 4000 USGPMHead to 400 ft.
Speed to 3600 rpmMetallurgy Cast Iron,
Alloys, Exotics
Non-clog Solids Handling, Vertical/Horizontal Dry Pit Solids HandlingSize to 12x10x19Capacity to 6000 USGPMHead to 250 ft.Speed to 1800 rpmMetallurgy Cast Iron, Bronze, Alloys
Refuse Wet Pit/Dry Pit Solids Handling
Size to 4x4x10Capacity to 600 USGPM
Head to 100 ft.Speed to 1800 rpm
Metallurgy Cast Iron, Alloys
Vertical Cantilever Vertical ProcessSize to 10x8x16Capacity to 4000 USGPMHead to 300 ft.Speed to 3600 rpmMetallurgy Cast Iron, Alloys, Exotics
Vertical Sump Wet Pit Service
Size to 10x8x16Capacity to 4000 USGPM
Head to 300 ft.Speed to 3600 rpm
Metallurgy Cast Iron, Alloys, Exotics
18.
L/S
CFM
MIGD
IGPM
USGPM CFS
M3/H
M3/D
M3/S
7.48 60
24
4544694.4
13.208
15.850101.9428.31
3.6
86.4
52.59
13.208
1000
15.852.119
M3
Ft3
In3
L
US Gal Acre Ft
MIG
Yd3
Imp Gal
7.48 43560
5941
4665661.02
4.543
1.20 3.6831233.49
4542.6
1.31
61020
1000
220.14
264.235.31
kPa
Ins. Hg
mm Hg
m
PSI Atmos
Ft.
kg/cm2
H20
2.036 29.92
32.84
737.6373.42
39.37
27.71 33.96101.3
2.984
98.07
7.50
9.79
4.02
6.894
3.386
L/S
CFM
MIGD
IGPM
USGPM CFS
M3/H
M3/D
M3/S
7.48 60
24
4544694.4
13.208
15.850101.9428.31
3.6
86.4
52.59
13.208
1000
15.852.119
M3
Ft3
In3
L
US Gal Acre Ft
MIG
Yd3
Imp Gal
7.48 43560
5941
4665661.02
4.543
1.20 3.6831233.49
4542.6
1.31
61020
1000
220.14
264.235.31
kPa
Ins. Hg
mm Hg
m
PSI Atmos
Ft.
kg/cm2
H20
2.036 29.92
32.84
737.6373.42
39.37
27.71 33.96101.3
2.984
98.07
7.50
9.79
4.02
6.894
3.386
L/S
CFM
MIGD
IGPM
USGPM CFS
M3/H
M3/D
M3/S
7.48 60
24
4544694.4
13.208
15.850101.9428.31
3.6
86.4
52.59
13.208
1000
15.852.119
M3
Ft3
In3
L
US Gal Acre Ft
MIG
Yd3
Imp Gal
7.48 43560
5941
4665661.02
4.543
1.20 3.6831233.49
4542.6
1.31
61020
1000
220.14
264.235.31
kPa
Ins. Hg
mm Hg
m
PSI Atmos
Ft.
kg/cm2
H20
2.036 29.92
32.84
737.6373.42
39.37
27.71 33.96101.3
2.984
98.07
7.50
9.79
4.02
6.894
3.386
CONVERSION CHARTS
FLOW
PRESSURE
VOLUME
Multiply in direction of arrow. Divide in opposite direction.
Multiply in direction of arrow. Divide in opposite direction.
Multiply in direction of arrow. Divide in opposite direction.
Smart Turner Pumps Inc.392 Hardy Road, P.O. Box 28066,Brantford, Ontario, N3R7X5, Canada
TEL: 1-888-561-PUMP (7867) FAX: (519) 757-1747EMAIL: [email protected]: www.smartturner.ca
English Metric Decimal English Metric Decimal English Metric Decimal English Metric Decimal
.. .1 .0039 45 .. .0820 5 .. .2055 7/16 .. .4375 .2 .0079 44 .. .0860 4 .. .2090 29/64 .. .4531 .. .3 .0118 43 .. .0890 3 .. .2130 15/32 .. .4687 80 .. .0135 42 .. .0935 7/32 . .2187 .. 12. .4724 79 . .0145 3/32 .. .0937 2 .. .2210 31/64 .. .4844 1/64 .. .0156 41 .. .0960 1 .. 2280 1/2 .. .5000 .. .4 .0157 40 .. .0980 A .. .2340 .. 13. .5118 78 . .0160 39 .. .0995 15/64 .. .2344 33/64 .. 5156 77 . .0180 38 .. .1015 .. 6. .2362 17/32 .. .5312 . .5 .0197 37 .. .1040 B .. .2380 35/64 .. .5469 76 . .0200 36 .. .1065 C .. .2420 .. 14. .5512 75 . .0210 7/64 .. .1094 D .. .2460 9/16 .. .5625 74 . .0225 35 .. .1100 1/4 .. .2500 37/64 .. .5781 . .6 .0236 34 .. .1110 F .. .2570 .. 15. .5906 73 .. .0240 33 .. .1130 G .. .2610 19/32 .. .5937 72 .. .0250 32 .. .1160 17/64 .. .2656 39/64 .. .6094 71 .. .0260 .. 3. .1181 H .. .2660 5/8 .. .6250 .. .7 .0276 31 . .1200 I .. .2720 .. 16. .6299 70 .. .0280 1/8 .. .1250 .. 7. .2756 41/64 .. .6406 69 .. .0292 30 .. .1285 J .. .2770 21/32 .. .6562 68 .. .0310 29 .. .1360 K .. .2810 .. 17. .6693 1/32 .. .0312 28 .. .1405 9/32 .. .2812 43/64 .. .6719 .. .8 .0315 9/64 .. .1406 L .. .2900 11/16 .. .6875 67 .. .0320 27 .. .1440 M .. .2950 45/64 .. .7031 66 .. .0330 26 . .1470 19/64 .. .2969 .. 18. .7087 65 .. .0350 25 .. .1495 N .. .3020 23/32 .. .7187 . .9 .0354 24 .. .1520 5/16 .. .3125 47/64 .. .7344 64 .. .0360 23 .. .1540 .. 8. .3150 .. 19. .7480 63 .. .0370 5/32 . .1562 O .. .3160 3/4 .. .7500 62 .. .0380 22 .. .1570 P .. .3230 49/64 .. .7656 61 .. .0390 .. 4. .1575 21/64 .. .3281 25/32 .. .7812 .. 1. .0394 21 .. .1590 Q .. .3320 .. 20. .7874 60 .. .0400 20 .. .1610 R .. .3390 51/64 .. .7969 59 .. .0410 19 .. .1660 11/32 .. .3437 13/16 .. .8125 58 .. .0420 18 . .1695 S .. .3480 .. 21. .8268 57 . .0430 11/64 .. .1719 .. 9. .3543 53/64 .. .8281 56 .. .0465 17 . .1730 T .. .3580 27/32 .. .8437 3/64 .. .0469 16 .. .1770 23/64 .. .3594 55/64 .. .8594 55 .. .0520 15 .. .1800 U .. .3680 .. 22. .8661 54 .. .0550 14 .. .1820 3/8 .. .3750 7/8 .. .8750 53 .. .0595 13 .. .1850 V … .3770 57/64 .. .8906 1/16 . .0625 3/16 .. .1875 W .. .3860 .. 23. .9055 52 .. .0635 12 .. .1890 25/64 .. .3906 29/32 .. .9062 51 .. .0670 11 .. .1910 .. 10. .3937 59/64 .. .9219 50 .. .0700 10 .. .1935 X .. .3970 15/16 .. .9375 49 . .0730 9 .. .1960 Y . .4040 .. 24. .9449 48 .. .0760 .. 5. .1968 13/32 .. .4062 61/64 .. .9531 5/64 .. .0781 8 .. .1990 Z .. .4130 31/32 .. .9687 47 .. .0785 7 .. .2010 27/64 .. .4219 .. 25. .9842 .. 2. .0787 13/64 .. .2031 .. 11. .4331 63/64 .. .9844 46 .. .0810 6 .. .2040 1 25.4 1.000
DECIMAL EQUIVALENTS
TAP DRILL CHARTRECOMMEND TAP DRILL TO USE FOR 75% DEPTH OF THREAD
Nom. Size Tap Use Drill Bit (Closest) Decimal
0-80 NF 3/64” 3/64” .0469 1-64 NC #53 - .0595 1-72 NF #53 1/16” .0595 2-56 NC #50 - .0700 2-64 NF #50 - .0700 3-48 NC #47 5/64” .0785 3-56 NF #45 - .0820 4-36 NS #44 - .0860 4-40 NC #43 3/32” .0890 4-48 NF #42 3/32” .0935 3mm-0.60mm 2.5mm - .0984 1/8-40 NS #38 - .1015 5-40 NC #38 - .1015 5-44 NF #37 - .1040 6-32 NC #35 7/64” .1100 6-36 NS #34 - .1110 6-40 NF #33 - .1130 6-48 NS #31 - .1200 4mm-0.70mm 3.4mm - .1338 4mm-0.75mm 3.4mm - .1338 8-32 NC #29 - .1360 8-36 NF #29 9/64” .1360 8-40 NS #28 - .1405 3/16-24 NS #26 - .1470 10-24 NC #25 5/32” .1495 3/16-32 NS #22 - .1570 10-32 NF #21 5/32” .1590 5mm-0.90mm 4.2mm - .1653 5mm-0.80mm 4.3mm - .1693 12-24 NC #16 11/64” .1770 12-28 NF #14 3/16” .1820 12-32 NEF #13 - .1850
Nom. Size Tap Use Drill Bit (Closest) Decimal
14-20 NS #10 - .1935 1/4-20 NC #7 13/64” .2010 14-24 NS #7 - .2010 6mm-1.00mm 5.2mm - .2047 1/4-24 NS #4 - .2090 1/4-28 NF #3 7/32” .2130 1/4-32 NEF 7/32” 7/32” .2188 1/4-40 NS #1 - .2280 7mm-1.00mm 6.1mm 15/64” .2401 5/16-18 NC Ltr.F 17/64” .2570 8mm-1.25mm 6.9mm 17/64” .2716 5/16-24 NF Ltr.I - .2720 8mm-1.00mm 7.1mm - .2795 5/16-32 NEF 9/32” 9/32” .2812 9mm-1.25mm 7.9mm - .3110 3/8-16 NC 5/16” 5/16” .3125 9mm-1.00mm 8.1mm - .3189 9mm-0.75mm 8.3mm - .3268 3/8-24 NF Ltr.Q 21/64” .3320 10mm-1.50mm 8.7mm - .3425 10mm-1.25mm 8.9mm 11/32” .3503 10mm-1.00mm 9.1mm - .3583 7/16-14 NC Ltr.U 23/64” .3680 11mm-1.50mm 9.7mm - .3818 7/16-20 NF 25/64” 25/64” .3906 12mm-1.75mm 10.5mm - .4133 12mm-1.50mm 10.7mm 27/64” .4212 1/2-13 NC 27/64” 27/64” .4219 12mm-1.25mm* 10.9mm 27/64” .4291 1/2-20 NF 29/64” 29/64” .4531 1/2-24 NS 29/64” 29/64” .4531 14mm-2.00mm 12.2mm - .4803
Nom. Size Tap Use Drill Bit (Closest) Decimal
9/16-12 NC 31/64” 31/64” .4844 14mm-1.50mm 12.7mm - .4999 14mm-1.25mm* 12.8mm - .5039 9/16-18 NF 33/64” 33/64” .5156 5/8-11 NC 17/32” 17/32” .5312 16mm-2.00mm 14.2mm 35/64” .5590 5/8-18 NF 37/64” 37/64” .5781 16mm-1.50mm 14.7mm - .5787 11/16-11 NS 19/32” 19/32” .5938 18mm-2.50mm 15.8mm 39/64” .6220 11/16-16 NS 5/8” 5/8” .6250 3/4-10 NC 21/32” 21/32” .6562 18mm-1.50mm* 16.8mm - .6614 3/4-16 NF 11/16” 11/16” .6875 20mm-2.50mm 17.8mm 11/16” .7008 7/8-9 NC 49/64” 49/64” .7656 7/8-14 NF 13/16” 13/16” .8125 22mm-1.50mm 20.9mm - .8228 7/8-18 NS* 53/64” 53/64” .8281 24mm-3.00mm 21.4mm 53/64” .8425 1.8 NC 7/8” 7/8” .8750 24mm-2.00mm 22.3mm - .8779 1.12 NF 59/64” 59/64” .9219 1-14 NS 15/16” 15/16” .9375 1 1/8-7 NC 63/64” 63/64” .9844 1 1/8-12 NF 1 3/64” 1 3/64” 1.0469 1 1/4-7 NC 1 7/64” 1 7/64” 1.1094 1 1/4-12 NF 1 11/64” 1 11/64” 1.1719 1 3/8-6 NC 1 7/32” 1 7/32” 1.2188 1 3/8-12 NF 1 19/64” 1 19/64” 1.2969 1 1/2-6 NC 1 11/32” 1 11/32” 1.3438 1 1/2”-12 NF 1 27/64” 1 27/64” 1.4219
19.
ASME B73.1 / ANSI END SUCTION PUMPSThis catalogue provides the information you need to select a Smart Turn-er ASME B73.1 Pump to fit your specific needs. The ASME End Suction Pump range continues the Smart Turner tradition of providing well prov-en, uncomplicated designs incorporating high efficiency and smooth, low NPSH performance in a compact economical, Heavy Duty End Suc-tion Pump.
Smart Turner ASME Pumps are ideally suited to plant service and chemi-cal process applications where continuous, reliable operation is essential, whether the fluid is clean, dirty, corrosive or abrasive.
Smart Turner ASME Pumps are quality built for rugged, trouble free op-eration. They are available with either grease or oil lubricated bearings as standard.
Smart Turner ASME Pumps are engineered to exceed ANSI standards in all essential features. Impeller adjustment is positive and uncomplicated. High shaft stiffness yields low shaft deflections. Oversize bearings pro-vide more than 2 year L10 life in all cases. The large stuffing box and the rear impeller pump out vanes provide excellent heat dissipation and low stuffing box pressure for long packing and seal life. The recessed pump out vane arrangement minimizes the effects of wear by maintaining pump out efficiency throughout the full range of impeller adjustment.
Smart Turner ASME Pumps are produced and stocked in a wide range of sizes using only three bearing housings. This makes an efficient parts in-ventory possible through extensive interchangeability of parts between pumps.
With the inclusion of ASME Pumps, Smart Turner can now offer a range of End Suction Pumps, totaling over 60 models, with capacities to 6000 USGPM, heads to 800 feet and speeds to 3500 Rpm.
This catalogue features ANSI End Suction Pumps. For other End Suction models, see catalogues B-90, D-90, F-90 and G-90.
20.
CONSTRUCTION MATERIALS• All Iron
• 316 Stainless Steel
• Steel
• Alloy 20
• CD4MCuN
• Hastelloy C
• Bronze
• Monel
• Other Materials on Application
HEAD OFFICE AND MAIN SALES OFFICE:Smart Turner Pumps Inc.392 Hardy Road, P.O. Box 28066,Brantford, Ontario, N3R7X5, CanadaTEL: (519) 757-1746 FAX: (519) 757-1747Website: www.smartturner.ca
DISTRIBUTION:Smart Turner Pumps Inc. takes great pride in it’s global distribution network. If you need it we will ship it, anywhere in the world.
REPRESENTED BY: