Report No.: AR362601-03AD Page : 1 of 69
Report Version: Rev. 01
AS/NZS Test Report
Equipment : BTv4.0 Dual Mode USB Dongle
Model No. : BT820
Brand Name : Laird Technologies
Applicant : Laird Technologies
Address : W66N220 Commerce Court, Cedarburg, Wisconsin 53012, USA
Standard : AS/NZS 4268:2017
Received Date : Jan. 23, 2017
Tested Date : Jan. 25 ~ Apr. 12, 2017
We, International Certification Corp., would like to declare that the tested sample has been evaluated and in compliance with the requirement of the above standards. The test results contained in this report refer exclusively to the product. It may be duplicated completely for legal use with the approval of the applicant. It shall not be reproduced except in full without the written approval of our laboratory. Reviewed by:
Approved by:
James Fan / Assistant Manager Gary Chang / Manager
Report No.: AR362601-03AD Page : 2 of 69
Report Version: Rev. 01
Table of Contents 1 GENERAL DESCRIPTION .................................................................................................................... 5
1.1 Information .............................................................................................................................................. 5 1.2 Local Support Equipment List ................................................................................................................ 7 1.3 Test Setup Chart .................................................................................................................................... 7 1.4 Test Equipment and Calibration Data .................................................................................................... 8 1.5 Testing Applied Standards ..................................................................................................................... 9 1.6 Measurement Uncertainty ...................................................................................................................... 9
2 TEST CONFIGURATION ..................................................................................................................... 10
2.1 Testing Condition ................................................................................................................................. 10 2.2 The Worst Test Modes and Channel Details ....................................................................................... 10
3 TRANSMITTER TEST RESULTS ........................................................................................................ 11
3.1 Maximum EIRP..................................................................................................................................... 11 3.2 Number of Hopping Frequency ............................................................................................................ 13 3.3 20dB and Occupied Channel Bandwidth ............................................................................................. 15 3.4 Channel Separation .............................................................................................................................. 17 3.5 Number of Dwell Time .......................................................................................................................... 19
3.6 Operating Frequencies ......................................................................................................................... 22 3.7 Out of Band Emission ........................................................................................................................... 24 3.8 Transmitter Spurious Emissions ........................................................................................................... 29
4 RECEIVER TEST RESULTS ............................................................................................................... 48
4.1 Receiver Spurious Emissions ............................................................................................................... 48
5 PHOTOGRAPHS OF THE TEST CONFIGURATION ......................................................................... 67
6 TEST LABORATORY INFORMATION ............................................................................................... 69
Report No.: AR362601-03AD Page : 3 of 69
Report Version: Rev. 01
Release Record
Report No. Version Description Issued Date
AR362601-03AD Rev. 01 Initial issue Apr. 18, 2017
Report No.: AR362601-03AD Page : 4 of 69
Report Version: Rev. 01
Summary of Test Results
Ref. Std. Clause Test Items Measured Result
6.3 Maximum EIRP 9.57 dBm Pass
6.4 Transmitter Spurious Emissions Meet the requirement of limit. Pass
6.5 Emission Bandwidth Meet the requirement of limit. Pass
6.6 Operating Frequencies Meet the requirement of limit. Pass
7.2 Receiver Spurious Emissions Meet the requirement of limit. Pass
- Out of Band Emission Meet the requirement of limit. Pass
Row 55 Number of Hopping Frequency Meet the requirement of limit. Pass
Row 55 Channel Separation Meet the requirement of limit. Pass
Row 55 Dwell time Meet the requirement of limit. Pass
Report No.: AR362601-03AD Page : 5 of 69
Report Version: Rev. 01
1 General Description
1.1 Information
1.1.1 Specification of the Equipment under Test (EUT)
RF General Information
Frequency Range (MHz)
Bluetooth Mode
Ch. Frequency (MHz)
Channel Number Data Rate
2400-2483.5 BR 2402-2480 0-78 [79] 1 Mbps
2400-2483.5 EDR 2402-2480 0-78 [79] 2 Mbps
2400-2483.5 EDR 2402-2480 0-78 [79] 3 Mbps
Note 1: Bluetooth BR uses a GFSK. Note 2: Bluetooth EDR uses a combination of π/4-DQPSK and 8DPSK.
1.1.2 Antenna Details
Ant. No. Brand Model Type Gain (dBi) Connector
1 ACX AT3216-B2R7HA
A_3216 Chip 0.5 N/A
1.1.3 EUT Operational Condition
Supply Voltage 5Vdc from Host
Operational Voltage Vnom (5 V) Vmax (5.75 V) Vmin (4.25 V)
Operational Climatic Tnom (20°C) Tmax (85°C) Tmin (-40°C)
1.1.4 Accessories
N/A
Report No.: AR362601-03AD Page : 6 of 69
Report Version: Rev. 01
1.1.5 Channel List
Frequency band (MHz) 2400~2483.5
Channel Frequency
(MHz) Channel
Frequency (MHz)
Channel Frequency
(MHz) Channel
Frequency (MHz)
0 2402 20 2422 40 2442 60 2462
1 2403 21 2423 41 2443 61 2463
2 2404 22 2424 42 2444 62 2464
3 2405 23 2425 43 2445 63 2465
4 2406 24 2426 44 2446 64 2466
5 2407 25 2427 45 2447 65 2467
6 2408 26 2428 46 2448 66 2468
7 2409 27 2429 47 2449 67 2469
8 2410 28 2430 48 2450 68 2470
9 2411 29 2431 49 2451 69 2471
10 2412 30 2432 50 2452 70 2472
11 2413 31 2433 51 2453 71 2473
12 2414 32 2434 52 2454 72 2474
13 2415 33 2435 53 2455 73 2475
14 2416 34 2436 54 2456 74 2476
15 2417 35 2437 55 2457 75 2477
16 2418 36 2438 56 2458 76 2478
17 2419 37 2439 57 2459 77 2479
18 2420 38 2440 58 2460 78 2480
19 2421 39 2441 59 2461
1.1.6 Test Tool and Duty Cycle
Test Tool BlueTest3, version: 2.5.0
Duty Cycle Of Test Signal (%) BR: 78.93%, EDR: 80.16%
Duty Factor (dB) BR: 1.03, EDR: 0.96
Report No.: AR362601-03AD Page : 7 of 69
Report Version: Rev. 01
1.1.7 Power Setting
Modulation Mode Test Frequency (MHz)
2402 2441 2480
GFSK/1Mbps 63 63 63
8DPSK/3Mbps 63 63 63
1.2 Local Support Equipment List
Support Equipment List
No. Equipment Brand Model FCC ID Signal cable / Length (m)
1 Notebook DELL Latitude E6440 DoC ---
1.3 Test Setup Chart
Test Setup Diagram
Report No.: AR362601-03AD Page : 8 of 69
Report Version: Rev. 01
1.4 Test Equipment and Calibration Data
Test Item Radiated Emissions
Test Site Fully-anechoic chamber 2 / (05CH02-WS)
Tested Date Jan. 25, 2017
Instrument Manufacturer Model No. Serial No. Calibration Date Calibration Until
Spectrum Analyzer Agilent N9010A MY52221474 Oct. 14, 2016 Oct. 13, 2017
Bilog Antenna 30-1000MHz
SCHWARZBECK VULB9168 9168-563 Jan. 05, 2017 Jan. 04, 2018
Horn Antenna 1G-18G
SCHWARZBECK BBHA 9120 D 9120D-1205 Jan. 05, 2017 Jan. 04, 2018
Horn Antenna 18G-40G
SCHWARZBECK BBHA 9170 BBHA 9170508 Dec. 29, 2016 Dec. 28, 2017
Preamplifier Agilent 83017A MY53270013 Jan. 10, 2017 Jan. 09, 2018
Preamplifier 30-1000MHz
EMC EMC02325 980188 Dec. 13, 2016 Dec. 12, 2017
Preamplifier EMC EMC184045B 980192 Aug. 24, 2016 Aug. 23, 2017
RF cable-1M HUBER+SUHNER SUCOFLEX104 MY22622/4 Dec. 13, 2016 Dec. 12, 2017
RF cable-1M HUBER+SUHNER SUCOFLEX104 MY22623/4 Dec. 14, 2016 Dec. 13, 2017
RF cable-3M HUBER+SUHNER SUCOFLEX104 MY22621/4 Dec. 14, 2016 Dec. 13, 2017
RF cable-4M HUBER+SUHNER SUCOFLEX104 MY22579/4 Dec. 14, 2016 Dec. 13, 2017
LF cable-0.8M EMC EMC8D-NM-NM-800 EMC8D-NM-NM-800
-002 Dec. 14, 2016 Dec. 13, 2017
LF cable-3M EMC EMC8D-NM-NM-300
0 131102 Dec. 14, 2016 Dec. 13, 2017
LF cable-10M EMC EMC8D-NM-NM-100
00 131101 Dec. 14, 2016 Dec. 13, 2017
Measurement Software
AUDIX e3 6.120210g NA NA
Note: Calibration Interval of instruments listed above is one year.
Test Item RF Conducted
Test Site (TH01-WS)
Tested Date Feb. 06, 2017
Instrument Manufacturer Model No. Serial No. Calibration Date Calibration Until
Spectrum Analyzer ROHDE&SCHWARZ FSV40 101486 Nov. 15, 2016 Nov. 14, 2017
TEMP&HUMIDITY CHAMBER
GIANT FORCE GCT-225-40-SP-SD MAF1212-002 Nov. 21, 2016 Nov. 20, 2017
Power Meter Anritsu ML2495A 1241001 Aug. 24, 2016 Aug. 23, 2017
Power Sensor Anritsu MA2411B 1207362 Aug. 24, 2016 Aug. 23, 2017
DC POWER SOURCE
GW INSTEK GPC-6030D EM892433 Oct. 20, 2016 Oct. 19, 2017
Measurement Software
Sporton Sporton_1 1.3.30 NA NA
Measurement Software
Agilent EN RF test 1.1501125 NA NA
Note: Calibration Interval of instruments listed above is one year.
Report No.: AR362601-03AD Page : 9 of 69
Report Version: Rev. 01
Test Item Radiated Emissions
Test Site (10CH02-HY)
Tested Date Apr. 12, 2017
Instrument Manufacturer Model No. Serial No. Calibration Date Calibration Until
Spectrum Analyzer R&S FSP7 100645 Apr. 25, 2016 Apr. 24, 2017
Receiver R&S ESI7 838496/008 Sep. 01, 2016 Aug. 31, 2017
Amplifier Agilent 8447D 2944A10828 Feb. 16, 2017 Feb. 15, 2018
Amplifier Agilent 8447D 2944A10827 Jan. 24, 2017 Jan. 23, 2018
RF Cable-R10m Jye Bao RG142 CB027-INSIDE Dec. 30, 2016 Dec. 29, 2017
RF Cable-R10m MTJ RG223/U + RG8/U CB026-DOOR Dec. 30, 2016 Dec. 29, 2017
Loop Antenna R&S HFH2-Z2 100330 Nov. 10, 2016 Nov. 09, 2017
Software Audix E3 4.03260c ---
Note: Calibration Interval of instruments listed above is one year.
1.5 Testing Applied Standards
According to the specifications of the manufacturer, the EUT must comply with the requirements of the following standards:
AS/NZS 4268:2017
1.6 Measurement Uncertainty
ISO/IEC 17025 requires that an estimate of the measurement uncertainties associated with the emissions test results be included in the report. The measurement uncertainties given below are based on a 95% confidence level (based on a coverage factor (k=2)
Measurement Uncertainty
Parameters Uncertainty
Radio Frequency ±1.4 x 10-9
RF power conducted ±0.808 dB
RF power radiated ±3.401 dB
Spurious emission, conducted ±2.994 dB
Spurious emission, radiated ±3.401 dB
Humidity ±0.6 oC
Temperature ±0.29 %
Time ±0.1 %
Report No.: AR362601-03AD Page : 10 of 69
Report Version: Rev. 01
2 Test Configuration
2.1 Testing Condition
Testing Location
ICC Lab ADD : No.3-1, Lane 6, Wen San 3rd St., Kwei Shan District, Tao Yuan City 333, Taiwan (R.O.C.)
TEL : 886-3-271-8666 FAX : 886-3-318-0155
Sporton Lab ADD : No. 52, Huaya 1st Rd., Guishan Dist., Taoyuan City, Taiwan (R.O.C.)
TEL : 886-3-327-3456 FAX : 886-3-327-0973
Test Condition Test Site No. Test Engineer Test Environment
Radiated Emission > 30
MHz 05CH02-WS 24°C / 65% Penguin Jiang
RF Conducted TH01-WS 22.1°C / 61% Chris Zeng
Radiated Emission ≤ 30MHz
10CH02-HY* 22.1°C / 61% Jack Li
Note: * ICC lab subcontracts this test item to Sporton Lab (TAF:1190).
Sporton Lab is a TAF accreditation test firm and also is an approved provider of ICC lab.
2.2 The Worst Test Modes and Channel Details
Test item Modulation
Mode Test Frequency
(MHz) Data Rate
Test Configuration
Maximum EIRP
Emission Bandwidth
GFSK 8DPSK
2402 / 2441 / 2480 2402 / 2441 / 2480
1 Mbps 3 Mbps
---
Operating Frequencies GFSK
8DPSK 2402 / 2480 2402 / 2480
1 Mbps 3 Mbps
---
Transmitter Spurious Emissions GFSK
8DPSK 2402 / 2441 / 2480 2402 / 2441 / 2480
1 Mbps 3 Mbps
---
Receiver Spurious Emissions GFSK
8DPSK 2402 / 2441 / 2480 2402 / 2441 / 2480
1 Mbps 3 Mbps
---
Out of Band Emission GFSK
8DPSK 2402 / 2441 / 2480 2402 / 2441 / 2480
1 Mbps 3 Mbps
Number of Hopping Frequency GFSK
8DPSK 2402 ~ 2480 2402 ~ 2480
1 Mbps 3 Mbps
Channel Separation GFSK
8DPSK 2402 / 2441 / 2480 2402 / 2441 / 2480
1 Mbps 3 Mbps
Dwell time GFSK
8DPSK 2402 / 2480 2402 / 2480
1 Mbps 3 Mbps
Report No.: AR362601-03AD Page : 11 of 69
Report Version: Rev. 01
3 Transmitter Test Results
3.1 Maximum EIRP
3.1.1 EIRP Limits
The equivalent isotropic radiated power (e.i.r.p.) shall be equal to or less than 0.5 W (27dBm).
3.1.2 Test Procedures
Reference to clause 5.4.2.2 of ETSI EN 300 328 V2.1.1 (2016-11).
3.1.3 Test Setup
Report No.: AR362601-03AD Page : 12 of 69
Report Version: Rev. 01
3.1.4 Test Result of EIRP
Condition Freq. (MHz) EIRP Power (dBm)
Limit (dBm) Results GFSK/1Mbps 8DPSK/3Mbps
TnomVnom 2402 6.19 5.01 27 Pass
TminVmax 2402 6.85 5.15 27 Pass
TminVmin 2402 6.87 5.12 27 Pass
TmaxVmax 2402 4.71 3.56 27 Pass
TmaxVmin 2402 4.70 3.53 27 Pass
TnomVnom 2441 7.50 6.60 27 Pass
TminVmax 2441 8.24 6.89 27 Pass
TminVmin 2441 8.26 6.88 27 Pass
TmaxVmax 2441 6.02 5.11 27 Pass
TmaxVmin 2441 6.00 5.08 27 Pass
TnomVnom 2480 8.74 7.86 27 Pass
TminVmax 2480 9.57 8.19 27 Pass
TminVmin 2480 9.54 8.15 27 Pass
TmaxVmax 2480 7.34 6.24 27 Pass
TmaxVmin 2480 7.32 6.27 27 Pass
Report No.: AR362601-03AD Page : 13 of 69
Report Version: Rev. 01
3.2 Number of Hopping Frequency
3.2.1 Limit of Number of Hopping Frequency
A minimum of 15 hopping frequencies shall be used.
3.2.2 Test Procedures
1. Set RBW = 100kHz, VBW = 300kHz, Sweep time = Auto, Detector = Peak Trace max hold.
2 Allow trace to stabilize.
3.2.3 Test Setup
Report No.: AR362601-03AD Page : 14 of 69
Report Version: Rev. 01
3.2.4 Test Result of Number of Hopping Frequency
GFSK 8DPSK
Report No.: AR362601-03AD Page : 15 of 69
Report Version: Rev. 01
3.3 20dB and Occupied Channel Bandwidth
3.3.1 Test Procedures
1. Set RBW=30kHz, VBW=100kHz,Sweep time = Auto, Detector=Peak Trace max hold
2 Allow trace to stabilize
3 Use N dB function of spectrum analyzer to measuring 20 dB bandwidth
4. Use Occupied bandwidth function of spectrum analyzer to measuring 99% occupied bandwidth
3.3.2 Test Setup
Report No.: AR362601-03AD Page : 16 of 69
Report Version: Rev. 01
3.3.3 Test Result of 20dB and Occupied Channel Bandwidth
Modulation Mode Frequency (MHz) 99% Bandwidth (MHz) 20dB Bandwidth (MHz)
GFSK/1Mbps 2402 0.89 0.99
GFSK/1Mbps 2441 0.89 0.98
GFSK/1Mbps 2480 0.89 0.98
8DPSK/3Mbps 2402 1.23 1.42
8DPSK/3Mbps 2441 1.24 1.42
8DPSK/3Mbps 2480 1.24 1.43
Worst Plot of 20dB Bandwidth Worst Plot of Occupied Bandwidth
Report No.: AR362601-03AD Page : 17 of 69
Report Version: Rev. 01
3.4 Channel Separation
3.4.1 Limit of Channel Separation
The centre frequencies shall be separated by a frequency separation greater than the larger of either 25 kHz or two thirds of the −20 dB bandwidth of the emission.
3.4.2 Test Procedures
1. Set RBW=100kHz, VBW=300kHz,Sweep time = Auto, Detector=Peak Trace max hold
2 Allow trace to stabilize
3 Use the marker-delta function to determine the separation between the peaks of the adjacent channels. The EUT shall show compliance with the appropriate regulatory limit
3.4.3 Test Setup
Report No.: AR362601-03AD Page : 18 of 69
Report Version: Rev. 01
3.4.4 Test result of Channel Separation
Modulation Mode Freq. (MHz) Channel
Separation (MHz) 20dB Bandwidth
(MHz) Minimum Limit
(MHz)
GFSK 2402 1.000 0.99 0.660
GFSK 2441 1.000 0.98 0.653
GFSK 2480 1.000 0.98 0.653
8DPSK 2402 1.000 1.42 0.947
8DPSK 2441 1.000 1.42 0.947
8DPSK 2480 1.000 1.43 0.953
GFSK 8DPSK
Report No.: AR362601-03AD Page : 19 of 69
Report Version: Rev. 01
3.5 Number of Dwell Time
3.5.1 Limit of Dwell time
The duration of the emission about any specific emission centre frequency shall not exceed 0.4 s.
3.5.2 Test Procedures
1. Set RBW=100kHz,VBW=300kHz,Sweep time = 500us(DH1),2ms(DH3),4ms(DH5), Detector=Peak, Span=0Hz,Trace max hold
2 Enable gating and trigger function of spectrum analyzer to measure burst on time.
3. The DH1 packet can cover a single time slot. A maximum length packet has duration of 1 time slots. The hopping rate is 1600 hops/second so the maximum dwell time is 1/1600 seconds, or 0.625ms. DH1 Packet permit maximum 1600 / 79 /2 = 10.12 hops per second in each channel (1 time slot RX, 1 time slot TX). So, the dwell time is the time duration of the pulse times 10.12 x 31.6 = 320 within 31.6 seconds.
4. The DH3 packet can cover up to 3 time slots. A maximum length packet has duration of 3 time slots. The hopping rate is 1600 hops/second so the maximum dwell time is 3/1600 seconds, or 1.875ms. DH3 Packet permit maximum 1600 / 79 / 4 = 5.06 hops per second in each channel (3 time slots RX, 1 time slot TX). So, the dwell time is the time duration of the pulse times 5.06 x 31.6 = 160 within 31.6 seconds.
5 The DH5 packet can cover up to 5 time slots. Operate DH5 at maximum dwell time and maximum duty cycle. A maximum length packet has duration of 5 time slots. The hopping rate is 1600 hops/second so the maximum dwell time is 5/1600 seconds, or 3.125ms. DH5 Packet permit maximum 1600/ 79 / 6 = 3.37 hops per second in each channel (5 time slots RX, 1 time slot TX). So, the dwell time is the time duration of the pulse times 3.37 x 31.6 = 106.6 within 31.6 seconds
3.5.3 Test Setup
Report No.: AR362601-03AD Page : 20 of 69
Report Version: Rev. 01
3.5.4 Test Result of Dwell Time
Modulation Mode Freq. (MHz) No. of Pulse in a
31.6 (79Hopping*0.4)
Length of Pulse Time (msec)
Result (msec)
Limit (msec)
GFSK 2402 320 0.44 140.80 400
GFSK 2441 160 1.68 268.80 400
GFSK 2480 106.6 2.94 313.40 400
8DPSK 2402 320 0.46 147.20 400
8DPSK 2441 160 1.70 272.00 400
8DPSK 2480 106.6 3.02 321.93 400
GFSK
DH1 DH5
DH3 -
-
Report No.: AR362601-03AD Page : 21 of 69
Report Version: Rev. 01
8DPSK
3DH1 3DH5
3DH3 -
-
Report No.: AR362601-03AD Page : 22 of 69
Report Version: Rev. 01
3.6 Operating Frequencies
3.6.1 Operating Frequencies Limits
The upper and lower frequency limit of the emission bandwidth shall at all times remain within the operating frequency (FL > 2,4 GHz and FH < 2,4835 GHz).
3.6.2 Test Procedures
1. Set RBW=30kHz, VBW=100kHz,Sweep time = Auto, Detector=Peak Trace max hold
2 Allow trace to stabilize
3. Use Occupied bandwidth function of spectrum analyzer to measuring 99% occupied bandwidth
4. Record the FL and FH
3.6.3 Test Setup
Report No.: AR362601-03AD Page : 23 of 69
Report Version: Rev. 01
3.6.4 Test Result of Operating Frequencies
Frequency Range (MHz)
Condition Modulation
Mode Freq. (MHz) FL and FH Limit Results
TnomVnom GFSK/1Mbps 2402 2401.55282 2400 Pass
TminVmax GFSK/1Mbps 2402 2401.53282 2400 Pass
TminVmin GFSK/1Mbps 2402 2401.53282 2400 Pass
TmaxVmax GFSK/1Mbps 2402 2401.58282 2400 Pass
TmaxVmin GFSK/1Mbps 2402 2401.58282 2400 Pass
TnomVnom GFSK/1Mbps 2480 2480.44284 2483.5 Pass
TminVmax GFSK/1Mbps 2480 2480.41284 2483.5 Pass
TminVmin GFSK/1Mbps 2480 2480.41284 2483.5 Pass
TmaxVmax GFSK/1Mbps 2480 2480.48284 2483.5 Pass
TmaxVmin GFSK/1Mbps 2480 2480.48284 2483.5 Pass
Frequency Range (MHz)
Condition Modulation
Mode Freq. (MHz) FL and FH Limit Results
TnomVnom 8DPSK/3Mbps 2402 2401.37916 2400 Pass
TminVmax 8DPSK/3Mbps 2402 2401.34916 2400 Pass
TminVmin 8DPSK/3Mbps 2402 2401.34916 2400 Pass
TmaxVmax 8DPSK/3Mbps 2402 2401.41916 2400 Pass
TmaxVmin 8DPSK/3Mbps 2402 2401.41916 2400 Pass
TnomVnom 8DPSK/3Mbps 2480 2480.60781 2483.5 Pass
TminVmax 8DPSK/3Mbps 2480 2480.58781 2483.5 Pass
TminVmin 8DPSK/3Mbps 2480 2480.58781 2483.5 Pass
TmaxVmax 8DPSK/3Mbps 2480 2480.63781 2483.5 Pass
TmaxVmin 8DPSK/3Mbps 2480 2480.63781 2483.5 Pass
Report No.: AR362601-03AD Page : 24 of 69
Report Version: Rev. 01
3.7 Out of Band Emission
3.7.1 Limit of Out of Band Emission
In any 100 kHz bandwidth outside the frequency band in which the transmitter is operating, the power shall be at least 20 dB below that in the 100 kHz bandwidth within the band that contains the highest level of the desired power.
3.7.2 Test Procedures
Reference level measurement
1. Set RBW=100kHz, VBW = 300kHz , Detector = Peak, Sweep time = Auto
2. Trace = max hold , Allow Trace to fully stabilize
3. Use the peak marker function to determine the maximum PSD level
Emission level measurement
1. Set RBW=100kHz, VBW = 300kHz , Detector = Peak, Sweep time = Auto
2. Trace = max hold , Allow Trace to fully stabilize
3. Scan Frequency range is up to 25GHz
4. Use the peak marker function to determine the maximum amplitude level
3.7.3 Test Setup
Report No.: AR362601-03AD Page : 25 of 69
Report Version: Rev. 01
3.7.4 Test result of Out of Band Emission
GFSK
Hopping on Hopping off
30MHz~25GHz (down 20dBc) TX Freq 2402MHz / 30MHz~25GHz (down 20dBc)
Report No.: AR362601-03AD Page : 26 of 69
Report Version: Rev. 01
Hopping off Hopping off
TX Freq 2441MHz / 30MHz~25GHz (down 20dBc) TX Freq 2480MHz / 30MHz~25GHz (down 20dBc)
Report No.: AR362601-03AD Page : 27 of 69
Report Version: Rev. 01
8DPSK
Hopping on Hopping off
30MHz~25GHz (down 20dBc) TX Freq 2402MHz / 30MHz~25GHz (down 20dBc)
Report No.: AR362601-03AD Page : 28 of 69
Report Version: Rev. 01
Hopping off Hopping off
TX Freq 2441MHz / 30MHz~25GHz (down 20dBc) TX Freq 2480MHz / 30MHz~25GHz (down 20dBc)
Report No.: AR362601-03AD Page : 29 of 69
Report Version: Rev. 01
3.8 Transmitter Spurious Emissions
3.8.1 Transmitter Spurious Emissions Limits
Spurious Emissions Limit (peak power)
Frequency Range Measurement Bandwidth
-56 dBW (2.5μW) e.i.r.p (59 dBμV/m at 10 metres)
< 150 kHz 1 kHz
150 kHz – 30 MHz 10 kHz
Frequency Range (MHz) Maximum power (dBm) Bandwidth (kHz)
30 to 47 -36 100
47 to 74 -54 100
74 to 87.5 -36 100
87.5 to 118 -54 100
118 to 174 -36 100
174 to 230 -54 100
230 to 470 -36 100
470 to 862 -54 100
862 to 1000 -36 100
1000 to 12750 -30 1000
3.8.2 Test Procedures
Reference to clause 5.4.9.2 of ETSI EN 300 328 V2.1.1 (2016-11).
Report No.: AR362601-03AD Page : 30 of 69
Report Version: Rev. 01
3.8.3 Test Setup
Below 30MHz
Below 1GHz
Above 1 GHz
Report No.: AR362601-03AD Page : 31 of 69
Report Version: Rev. 01
3.8.4 Transmitter Radiated Unwanted Emissions (Below 30MHz)
Freq. (MHz)
Modulation Channel Data Rate Freq. (MHz)
Emission Value
(dBuV/m)
SA Reading (dBuV)
Factor (dB)
Margin (dBuV/m)
Limit (dBuV/m)
Result
2402 GFSK
Ch00 1M
0.248 49.26 29.26 20 9.74 59 Pass
2480 Ch78 0.248 49.23 29.23 20 9.77 59 Pass
2402 8DPSK
Ch00 3M
0.248 49.12 29.12 20 9.88 59 Pass
2480 Ch78 0.248 49.05 29.05 20 9.95 59 Pass
Report No.: AR362601-03AD Page : 32 of 69
Report Version: Rev. 01
3.8.5 Transmitter Radiated Unwanted Emissions (Below 1GHz)
Modulation GFSK Test Freq. (MHz) 2402
Polarization Horizontal
Note 1: Measured Value (dBm) = Reading (dBm) + Factor (dB) Note 2: Margin (dB) = Measured Value (dBm) – Limit (dBm)
Report No.: AR362601-03AD Page : 33 of 69
Report Version: Rev. 01
Modulation GFSK Test Freq. (MHz) 2402
Polarization Vertical
Note 1: Measured Value (dBm) = Reading (dBm) + Factor (dB) Note 2: Margin (dB) = Measured Value (dBm) – Limit (dBm)
Report No.: AR362601-03AD Page : 34 of 69
Report Version: Rev. 01
Modulation GFSK Test Freq. (MHz) 2480
Polarization Horizontal
Note 1: Measured Value (dBm) = Reading (dBm) + Factor (dB) Note 2: Margin (dB) = Measured Value (dBm) – Limit (dBm)
Report No.: AR362601-03AD Page : 35 of 69
Report Version: Rev. 01
Modulation GFSK Test Freq. (MHz) 2480
Polarization Vertical
Note 1: Measured Value (dBm) = Reading (dBm) + Factor (dB) Note 2: Margin (dB) = Measured Value (dBm) – Limit (dBm)
Report No.: AR362601-03AD Page : 36 of 69
Report Version: Rev. 01
Modulation 8DPSK Test Freq. (MHz) 2402
Polarization Horizontal
Note 1: Measured Value (dBm) = Reading (dBm) + Factor (dB) Note 2: Margin (dB) = Measured Value (dBm) – Limit (dBm)
Report No.: AR362601-03AD Page : 37 of 69
Report Version: Rev. 01
Modulation 8DPSK Test Freq. (MHz) 2402
Polarization Vertical
Note 1: Measured Value (dBm) = Reading (dBm) + Factor (dB) Note 2: Margin (dB) = Measured Value (dBm) – Limit (dBm)
Report No.: AR362601-03AD Page : 38 of 69
Report Version: Rev. 01
Modulation 8DPSK Test Freq. (MHz) 2480
Polarization Horizontal
Note 1: Measured Value (dBm) = Reading (dBm) + Factor (dB) Note 2: Margin (dB) = Measured Value (dBm) – Limit (dBm)
Report No.: AR362601-03AD Page : 39 of 69
Report Version: Rev. 01
Modulation 8DPSK Test Freq. (MHz) 2480
Polarization Vertical
Note 1: Measured Value (dBm) = Reading (dBm) + Factor (dB) Note 2: Margin (dB) = Measured Value (dBm) – Limit (dBm)
Report No.: AR362601-03AD Page : 40 of 69
Report Version: Rev. 01
3.8.6 Transmitter Radiated Unwanted Emissions (Above 1GHz)
Modulation GFSK Test Freq. (MHz) 2402
Polarization Horizontal
Note 1: Measured Value (dBm) = Reading (dBm) + Factor (dB) Note 2: Margin (dB) = Measured Value (dBm) – Limit (dBm)
Report No.: AR362601-03AD Page : 41 of 69
Report Version: Rev. 01
Modulation GFSK Test Freq. (MHz) 2402
Polarization Vertical
Note 1: Measured Value (dBm) = Reading (dBm) + Factor (dB) Note 2: Margin (dB) = Measured Value (dBm) – Limit (dBm)
Report No.: AR362601-03AD Page : 42 of 69
Report Version: Rev. 01
Modulation GFSK Test Freq. (MHz) 2480
Polarization Horizontal
Note 1: Measured Value (dBm) = Reading (dBm) + Factor (dB) Note 2: Margin (dB) = Measured Value (dBm) – Limit (dBm)
Report No.: AR362601-03AD Page : 43 of 69
Report Version: Rev. 01
Modulation GFSK Test Freq. (MHz) 2480
Polarization Vertical
Note 1: Measured Value (dBm) = Reading (dBm) + Factor (dB) Note 2: Margin (dB) = Measured Value (dBm) – Limit (dBm)
Report No.: AR362601-03AD Page : 44 of 69
Report Version: Rev. 01
Modulation 8DPSK Test Freq. (MHz) 2402
Polarization Horizontal
Note 1: Measured Value (dBm) = Reading (dBm) + Factor (dB) Note 2: Margin (dB) = Measured Value (dBm) – Limit (dBm)
Report No.: AR362601-03AD Page : 45 of 69
Report Version: Rev. 01
Modulation 8DPSK Test Freq. (MHz) 2402
Polarization Vertical
Note 1: Measured Value (dBm) = Reading (dBm) + Factor (dB) Note 2: Margin (dB) = Measured Value (dBm) – Limit (dBm)
Report No.: AR362601-03AD Page : 46 of 69
Report Version: Rev. 01
Modulation 8DPSK Test Freq. (MHz) 2480
Polarization Horizontal
Note 1: Measured Value (dBm) = Reading (dBm) + Factor (dB) Note 2: Margin (dB) = Measured Value (dBm) – Limit (dBm)
Report No.: AR362601-03AD Page : 47 of 69
Report Version: Rev. 01
Modulation 8DPSK Test Freq. (MHz) 2480
Polarization Vertical
Note 1: Measured Value (dBm) = Reading (dBm) + Factor (dB) Note 2: Margin (dB) = Measured Value (dBm) – Limit (dBm)
Report No.: AR362601-03AD Page : 48 of 69
Report Version: Rev. 01
4 Receiver Test Results
4.1 Receiver Spurious Emissions
4.1.1 Receiver Spurious Emissions Limits
Spurious Emissions Limit (peak power)
Frequency Range Measurement Bandwidth
-56 dBW (2.5μW) e.i.r.p (59 dBμV/m at 10 metres)
< 150 kHz 1 kHz
150 kHz – 30 MHz 10 kHz
Frequency Range EIRP Limits (dBm)
25 MHz to 1 GHz -57
1 GHz to 26.5 GHz -47
4.1.2 Test Procedures
Reference to clause 5.4.10.2 of ETSI EN 300 328 V2.1.1 (2016-11).
Report No.: AR362601-03AD Page : 49 of 69
Report Version: Rev. 01
4.1.3 Test Setup
Below 30MHz
Below 1GHz
Above 1 GHz
Report No.: AR362601-03AD Page : 50 of 69
Report Version: Rev. 01
4.1.4 Receiver Radiated Unwanted Emissions (Below 30MHz)
Freq. (MHz)
Modulation Channel Data Rate Freq. (MHz)
Emission Value
(dBuV/m)
SA Reading (dBuV)
Factor (dB)
Margin (dBuV/m)
Limit (dBuV/m)
Result
2402 GFSK
Ch00 1M
0.248 49.26 29.26 20 9.74 59 Pass
2480 Ch78 0.248 49.19 29.19 20 9.81 59 Pass
2402 8DPSK
Ch00 3M
0.248 48.8 28.8 20 10.2 59 Pass
2480 Ch78 0.248 48.95 28.95 20 10.05 59 Pass
Report No.: AR362601-03AD Page : 51 of 69
Report Version: Rev. 01
4.1.5 Receiver Radiated Unwanted Emissions (Below 1GHz)
Modulation GFSK Test Freq. (MHz) 2402
Polarization Horizontal
Note 1: Measured Value (dBm) = Reading (dBm) + Factor (dB) Note 2: Margin (dB) = Measured Value (dBm) – Limit (dBm)
Report No.: AR362601-03AD Page : 52 of 69
Report Version: Rev. 01
Modulation GFSK Test Freq. (MHz) 2402
Polarization Vertical
Note 1: Measured Value (dBm) = Reading (dBm) + Factor (dB) Note 2: Margin (dB) = Measured Value (dBm) – Limit (dBm)
Report No.: AR362601-03AD Page : 53 of 69
Report Version: Rev. 01
Modulation GFSK Test Freq. (MHz) 2480
Polarization Horizontal
Note 1: Measured Value (dBm) = Reading (dBm) + Factor (dB) Note 2: Margin (dB) = Measured Value (dBm) – Limit (dBm)
Report No.: AR362601-03AD Page : 54 of 69
Report Version: Rev. 01
Modulation GFSK Test Freq. (MHz) 2480
Polarization Vertical
Note 1: Measured Value (dBm) = Reading (dBm) + Factor (dB) Note 2: Margin (dB) = Measured Value (dBm) – Limit (dBm)
Report No.: AR362601-03AD Page : 55 of 69
Report Version: Rev. 01
Modulation 8DPSK Test Freq. (MHz) 2402
Polarization Horizontal
Note 1: Measured Value (dBm) = Reading (dBm) + Factor (dB) Note 2: Margin (dB) = Measured Value (dBm) – Limit (dBm)
Report No.: AR362601-03AD Page : 56 of 69
Report Version: Rev. 01
Modulation 8DPSK Test Freq. (MHz) 2402
Polarization Vertical
Note 1: Measured Value (dBm) = Reading (dBm) + Factor (dB) Note 2: Margin (dB) = Measured Value (dBm) – Limit (dBm)
Report No.: AR362601-03AD Page : 57 of 69
Report Version: Rev. 01
Modulation 8DPSK Test Freq. (MHz) 2480
Polarization Horizontal
Note 1: Measured Value (dBm) = Reading (dBm) + Factor (dB) Note 2: Margin (dB) = Measured Value (dBm) – Limit (dBm)
Report No.: AR362601-03AD Page : 58 of 69
Report Version: Rev. 01
Modulation 8DPSK Test Freq. (MHz) 2480
Polarization Vertical
Note 1: Measured Value (dBm) = Reading (dBm) + Factor (dB) Note 2: Margin (dB) = Measured Value (dBm) – Limit (dBm)
Report No.: AR362601-03AD Page : 59 of 69
Report Version: Rev. 01
4.1.6 Receiver Radiated Unwanted Emissions (Above 1GHz)
Modulation GFSK Test Freq. (MHz) 2402
Polarization Horizontal
Note 1: Measured Value (dBm) = Reading (dBm) + Factor (dB) Note 2: Margin (dB) = Measured Value (dBm) – Limit (dBm)
Report No.: AR362601-03AD Page : 60 of 69
Report Version: Rev. 01
Modulation GFSK Test Freq. (MHz) 2402
Polarization Vertical
Note 1: Measured Value (dBm) = Reading (dBm) + Factor (dB) Note 2: Margin (dB) = Measured Value (dBm) – Limit (dBm)
Report No.: AR362601-03AD Page : 61 of 69
Report Version: Rev. 01
Modulation GFSK Test Freq. (MHz) 2480
Polarization Horizontal
Note 1: Measured Value (dBm) = Reading (dBm) + Factor (dB) Note 2: Margin (dB) = Measured Value (dBm) – Limit (dBm)
Report No.: AR362601-03AD Page : 62 of 69
Report Version: Rev. 01
Modulation GFSK Test Freq. (MHz) 2480
Polarization Vertical
Note 1: Measured Value (dBm) = Reading (dBm) + Factor (dB) Note 2: Margin (dB) = Measured Value (dBm) – Limit (dBm)
Report No.: AR362601-03AD Page : 63 of 69
Report Version: Rev. 01
Modulation 8DPSK Test Freq. (MHz) 2402
Polarization Horizontal
Note 1: Measured Value (dBm) = Reading (dBm) + Factor (dB) Note 2: Margin (dB) = Measured Value (dBm) – Limit (dBm)
Report No.: AR362601-03AD Page : 64 of 69
Report Version: Rev. 01
Modulation 8DPSK Test Freq. (MHz) 2402
Polarization Vertical
Note 1: Measured Value (dBm) = Reading (dBm) + Factor (dB) Note 2: Margin (dB) = Measured Value (dBm) – Limit (dBm)
Report No.: AR362601-03AD Page : 65 of 69
Report Version: Rev. 01
Modulation 8DPSK Test Freq. (MHz) 2480
Polarization Horizontal
Note 1: Measured Value (dBm) = Reading (dBm) + Factor (dB) Note 2: Margin (dB) = Measured Value (dBm) – Limit (dBm)
Report No.: AR362601-03AD Page : 66 of 69
Report Version: Rev. 01
Modulation 8DPSK Test Freq. (MHz) 2480
Polarization Vertical
Note 1: Measured Value (dBm) = Reading (dBm) + Factor (dB) Note 2: Margin (dB) = Measured Value (dBm) – Limit (dBm)
Report No.: AR362601-03AD Page : 67 of 69
Report Version: Rev. 01
5 Photographs of the Test Configuration
Spurious Emission Test below 30MHz
Report No.: AR362601-03AD Page : 68 of 69
Report Version: Rev. 01
Spurious Emission Test above 30MHz
Report No.: AR362601-03AD Page : 69 of 69
Report Version: Rev. 01
6 Test laboratory information
Established in 2012, ICC provides foremost EMC & RF Testing and advisory consultation services by our
skilled engineers and technicians. Our services employ a wide variety of advanced edge test equipment and
one of the widest certification extents in the business.
International Certification Corp (EMC and Wireless Communication Laboratory), it is our definitive objective is
to institute long term, trust-based associations with our clients. The expectation we set up with our clients is
based on outstanding service, practical expertise and devotion to a certified value structure. Our passion is to
grant our clients with best EMC / RF services by oriented knowledgeable and accommodating staff.
Our Test sites are located at Linkou District and Kwei Shan District. Location map can be found on our
website http://www.icertifi.com.tw.
Linkou Kwei Shan Kwei Shan Site II
Tel: 886-2-2601-1640 Tel: 886-3-271-8666 Tel: 886-3-271-8640
No. 30-2, Ding Fwu Tsuen, Lin Kou District, New Taipei City, Taiwan, R.O.C.
No. 3-1, Lane 6, Wen San 3rd St., Kwei Shan District, Tao Yuan City 333, Taiwan, R.O.C.
No. 14-1, Lane 19, Wen San 3rd St., Kwei Shan District, Tao Yuan City 333, Taiwan, R.O.C..
If you have any suggestion, please feel free to contact us as below information
Tel: 886-3-271-8666
Fax: 886-3-318-0155
Email: [email protected]
══END══