+ All Categories
Home > Documents > Assembly Line Instructions

Assembly Line Instructions

Date post: 02-Jun-2018
Category:
Upload: stevvennz
View: 236 times
Download: 0 times
Share this document with a friend

of 13

Transcript
  • 8/11/2019 Assembly Line Instructions

    1/13

  • 8/11/2019 Assembly Line Instructions

    2/13

    Alex GaoJohn Dunsmore

    Steven GarverickTim Kaing

    Step 3: Next attach part A on the ends of each side, right after part D. It should look the same

    in the picture below.

    Step 4: Attach the wheels (part E) to the two sides. The wheels go on the stick like thing.

    Step 5: For the other set, attach part F to both sides. It should look like the picture below.

    Step 6: Once again, attach wheels to each side. The wheels go on the stick looking thing.

    And now, you have your two sets of wheels!

  • 8/11/2019 Assembly Line Instructions

    3/13

    Alex GaoJohn Dunsmore

    Steven GarverickTim Kaing

    How to make the body: Robot 1

    Part A Part B Part C Part D Part E

    Attach part E Attach Part D to Combine parts Attach part A to

    on the end of the corner of BCDE like so. connect the

    2 part Cs. Part B twice. 2 part Bs.

  • 8/11/2019 Assembly Line Instructions

    4/13

    Alex GaoJohn Dunsmore

    Steven GarverickTim Kaing

    Part F x1 Part G x2 Part H x2

    Part I x1 Part J x2 Part K x2

    Part L x4 Part M x1

    Attach 4 part Ls to part M Attach Part H to previous Attach part F to the back of

    as shown. part. part M to create the front bumper.

  • 8/11/2019 Assembly Line Instructions

    5/13

    Alex GaoJohn Dunsmore

    Steven GarverickTim Kaing

    Attach part G x2 to part J x2. Attach part K x2 to part J x2. Attach part I to previous part.

    Now attach previous part to the bumper.

    Next Attach the wheels to the base. One of the front and one in the back.

  • 8/11/2019 Assembly Line Instructions

    6/13

    Alex GaoJohn Dunsmore

    Steven GarverickTim Kaing

    Attach the steering unit and bumper to the base.

    Robot 2 will complete.

  • 8/11/2019 Assembly Line Instructions

    7/13

    Alex GaoJohn Dunsmore

    Steven GarverickTim Kaing

    How to Build the Engine Unit

    1. Gather Piece N, G, and B 2. Take Part B x2 and attach them in the middle

    3. Take the combined N+B and Combine G

    4. Finish Combination of N, G, and B

  • 8/11/2019 Assembly Line Instructions

    8/13

    Alex GaoJohn Dunsmore

    Steven GarverickTim Kaing

    5. Obtain part H x1

    6. Obtain Part C x4

    7. Combine Part H and C by placing each of the Part Cs in each corner of H.

  • 8/11/2019 Assembly Line Instructions

    9/13

    Alex GaoJohn Dunsmore

    Steven GarverickTim Kaing

    8. Obtain Part A x2 and attach them Side by Side to one side of the Combined C+H

    Combined Parts: A, C, and H

    9. Gather Part 0 and Q and Place Q directly in the Center

    10.Gather Combined O and Q and add part R Directly on top of Q

  • 8/11/2019 Assembly Line Instructions

    10/13

    Alex GaoJohn Dunsmore

    Steven GarverickTim Kaing

    11.Gather Parts M x2 and place them on top of Part Q on the far left and right side

    12.Gather Part Lx2 and add them to the left and right side of the Combined Center Piece (Q+R)

    13.Gather Pieces J, I, and K.P

    l

    a

    c

    e

    s

    P

    i

    e

    c

    e

    I

    o

    n

  • 8/11/2019 Assembly Line Instructions

    11/13

    Alex GaoJohn Dunsmore

    Steven GarverickTim Kaing

    top of R on one half

    Place J on the other side of I Place K on top of both J and I to combine them

    14.Gather Part F x4 and part M x2. Place all 4 parts of F on top of Part M on each Circle. Part M can

    go right above Part K.

    15.Now Gather Part P and Part D and place them around each side of the Center Unit as shown

    below.

  • 8/11/2019 Assembly Line Instructions

    12/13

    Alex GaoJohn Dunsmore

    Steven GarverickTim Kaing

    16.Now take the Major 3 Parts show Below and combine them:

    Part x Part y Part z

    17.First Combine Part z to Part Y on the Grey Side (Piece D). Then Part x to Part y+z on the red side(Part p)

  • 8/11/2019 Assembly Line Instructions

    13/13

    Alex GaoJohn Dunsmore

    Steven GarverickTim Kaing

    18.Congratulations You're Now done!

    Evaluation :

    1.) Bold titles to be more specific

    2.) Dont stretch out pictures

    3.) Too many Steps and pictures


Recommended