TRAINING & READINESS SUPPLEMENT
ATC OFFICER
Air Traffic Control Facility 15 Aug 2019
Name
This supplement includes Lesson Topic Guides (LTGs) and Local Qualification Standards (LQSs) for Marine Corps
Air Station Cherry Point as required by ATC NATOPS and NAVMC 3500.94B, Chapter 7, Training & Readiness
Manual.
The LTGs detail the reference materials and discussion items that support the Knowledge, Skills and Abilities (KSAs)
that must be satisfactorily completed in order to assign the applicable qualification or designation. The LQSs are
divided into KSAs. The time allowed to complete this T&R Supplement is defined by the ATC Facility Manual and
shall not exceed the requirements of the T&R Directive. The actual completion data for each position qualification,
to include total number of days and total number of hours, shall be collected and analyzed by the facility’s training
branch. These data support Continuous Process Improvement within the facility and aid in projects and planning at
the regional level.
Knowledge is checked with a written test. All Knowledge tests shall be completed with a minimum passing score of
80% prior to the trainee reaching 25% of the established OJT time limit. Skills and Abilities may be accomplished
through OJT or simulation and shall be marked appropriately. LTGs and LQSs written in black are those required by
the T&R Directive, those written in red are supplemental information specifically for MCAS Cherry Point.
The following events are included in this supplement and taught in the associated Lesson Plan:
Event Description
ORNT-2000 Demonstrate an understanding of common ATC knowledge applicable to
Tower and Radar.
ACAD-0500 Comprehend general ATC knowledge.
ACAD-0501 Comprehend general ATC terminology.
ACAD-0502 Comprehend the airfield layout.
ACAD-0503 Comprehend local area/airfield specific information.
ACAD-0504 Comprehend location of ATC Facility Emergency/Safety Equipment.
ACAD-0505 Comprehend ATC emergency procedures and policies.
ACAD-0506 Comprehend the handling of special flights procedures and policies.
ACAD-0507 Comprehend basic weather knowledge.
ACAD-0508 Comprehend information contained in Local Letters of Agreement.
ACAD-0509 Comprehend knowledge of ATC publications.
ACAD-0520 Comprehend radio and interphone communications knowledge.
ACAD-0521 Comprehend aircraft movement data knowledge.
ACAD-0522 Comprehend flight progress strip knowledge.
ACAD-0523 Comprehend ATC clearance knowledge and phraseology.
EQPT-2003 Operate fixed control tower structure equipment.
EQPT-2004 Operate control tower messaging equipment.
COMM-2206 Operate control tower communications equipment.
ACAD-0524 Comprehend airfield lighting knowledge.
ACAD-0525 Comprehend requirements and phraseology for Special VFR operations.
ACAD-0527 Comprehend ATC phraseology/communications as it applies to ground
control.
ACAD-0528 Comprehend proper separation to vehicle and aircraft movement as it
applies to ground control.
ACAD-0532 Comprehend radar equipment knowledge.
ACAD-0534 Comprehend basic radar knowledge.
ACAD-0538 Comprehend radar coordination procedures.
EQPT-2019 Operate Radar Flight Data equipment.
COMM-2207 Operate radar communications equipment.
ACAD-0533 Comprehend radar final control knowledge.
EQPT-2018 Operate radar equipment.
OJT shall not commence until the required progression benchmarks are met.
ATC OFFICER
Table of Contents
Section I .................................... Training Plans
Section II .................................... Orientation
ORNT 1 – MCAS CHERRY POINT CHECK IN BRIEF
ORNT 2 – ATC KNOWLEDGE/TRAINING PROGRAM (ACAD-0500)
ORNT 3 – ATC TERMINOLOGY (ACAD-0501)
ORNT 4 – AIRFIELD LAYOUT (ACAD-0502)
ORNT 5 – LOCAL AREA/AIRFIELD SPECIFIC INFORMATION (ACAD-0503)
ORNT 6 – ATC FACILITY EMERGENCY/SAFETY EQUIPMENT (ACAD-0504)
ORNT 7 – EMERGENCY PROCEDURES AND POLICIES (ACAD-0505)
ORNT 8 – SPECIAL FLIGHTS (ACAD-0506)
ORNT 9 – WEATHER (ACAD-0507)
ORNT 10 – LETTERS OF AGREEMENT (ACAD-0508)
ORNT 11 – ATC PUBLICATIONS/FORMS (ACAD-0509)
Section III .................................... Radar Flight Data (RD)
LTG 1 - RADIO AND INTERPHONE COMMUNICATIONS (ACAD-0520)
LTG 2 - AIRCRAFT MOVEMENT DATA (ACAD-0521)
LTG 3 – FLIGHT PROGRESS STRIPS (ACAD-0522)
LTG 4 – ATC CLEARANCE/PHRASEOLOGY (ACAD-0523)
LTG 13 – RADAR EQUIPMENT PRINCIPLES (ACAD-0532)
LTG 15 – BASIC RADAR (ACAD-0534)
LTG 19 – RADAR COORDINATION(ACAD-0538)
LTG 23 – RADAR EQUIPMENT(EQPT-2018)
LTG 24 – RADAR FLIGHT DATA EQUIPMENT (EQPT-2019)
LTG 25 – RADAR COMMUNICATIONS EQUIPMENT (COMM-2206)
LTG 26 - LOCAL PROCEDURES
Section IV .................................... Radar Final Control (FC)
LTG 1 - RADIO AND INTERPHONE COMMUNICATIONS (ACAD-0520)
LTG 2 - AIRCRAFT MOVEMENT DATA (ACAD-0521)
LTG 3 – FLIGHT PROGRESS STRIPS (ACAD-0522)
LTG 4 – ATC CLEARANCE/PHRASEOLOGY (ACAD-0523)
LTG 13 – RADAR EQUIPMENT PRINCIPLES (ACAD-0532)
LTG 14 – RADAR FINAL CONTROL (ACAD-0533)
LTG 15 – BASIC RADAR (ACAD-0534)
LTG 19 – RADAR COORDINATION(ACAD-0538)
LTG 23 – RADAR EQUIPMENT(EQPT-2018)
LTG 25 – RADAR COMMUNICATIONS EQUIPMENT (COMM-2206)
LTG 26 - LOCAL PROCEDURES
LTG 27 – BASIC INSTRUCTOR (IUT-5000/5010/5020)
Section V .................................... Tower Flight Data (FD)
LTG 1 - RADIO AND INTERPHONE COMMUNICATIONS (ACAD-0520)
LTG 2 - AIRCRAFT MOVEMENT DATA (ACAD-0521)
LTG 3 – FLIGHT PROGRESS STRIPS (ACAD-0522)
LTG 4 – ATC CLEARANCE/PHRASEOLOGY (ACAD-0523)
LTG 22 – EQUIPMENT (EQPT-2003)
LTG 24 – EQUIPMENT (EQPT-2019)
LTG 25 – COMMUNICATIONS EQUIPMENT (COMM-2206)
LTG 26 - LOCAL PROCEDURES
Section VI .................................... Ground Control (GC)
LTG 1 - RADIO AND INTERPHONE COMMUNICATIONS (ACAD-0520)
LTG 2 - AIRCRAFT MOVEMENT DATA (ACAD-0521)
LTG 3 – FLIGHT PROGRESS STRIPS (ACAD-0522)
LTG 4 – ATC CLEARANCE/PHRASEOLOGY (ACAD-0523)
LTG 5 – AIRFIELD LIGHTING (ACAD-0524)
LTG 6 – SPECIAL VFR (ACAD-0525)
LTG 8 – ATC PHRASEOLOGY/COMMUNICATIONS (ACAD-0527)
LTG 9 – VEHICLE AND AIRCRAFT MOVEMENT (ACAD-0528)
LTG 22 – EQUIPMENT (EQPT-2003)
LTG 25 – COMMUNICATIONS EQUIPMENT (COMM-2206)
LTG 26 - LOCAL PROCEDURES
LTG 27 – BASIC INSTRUCTOR (IUT-5000/5010/5020)
Section VII .................................... Progression Benchmarks
Section VIII .................................... Training & Readiness Events
Section I TRAINING PLAN
TRAINING PLAN
Trainee: Date:
Position: RADAR FLIGHT DATA Initial Training
SATCS: Subsequent Training
OJT Start Date 25% Date
Pre OJT Required 50% Date
Simulation Required 75% Date
100% Date
Objectives:
Trainee Signature/Date
Primary OJTI Signature/Date
Secondary OJTI Signature/Date
Ensure a copy of this training plan is on file in the ATC Training Office.
TRAINING PLAN
Trainee: Date:
Position: RADAR FINAL CONTROL Initial Training
SATCS: Subsequent Training
OJT Start Date 25% Date
Pre OJT Required 50% Date
Simulation Required 75% Date
100% Date
Objectives:
Trainee Signature/Date
Primary OJTI Signature/Date
Secondary OJTI Signature/Date
Ensure a copy of this training plan is on file in the ATC Training Office.
TRAINING PLAN
Trainee: Date:
Position: TOWER FLIGHT DATA Initial Training
SATCS: Subsequent Training
OJT Start Date 25% Date
Pre OJT Required 50% Date
Simulation Required 75% Date
100% Date
Objectives:
Trainee Signature/Date
Primary OJTI Signature/Date
Secondary OJTI Signature/Date
Ensure a copy of this training plan is on file in the ATC Training Office.
TRAINING PLAN
Trainee: Date:
Position: GROUND CONTROL Initial Training
SATCS: Subsequent Training
OJT Start Date 25% Date
Pre OJT Required 50% Date
Simulation Required 75% Date
100% Date
Objectives:
Trainee Signature/Date
Primary OJTI Signature/Date
Secondary OJTI Signature/Date
Ensure a copy of this training plan is on file in the ATC Training Office.
Section II ORIENTATION
ORNT 1 - MCAS CHERRY POINT CHECK IN BRIEF
Lesson Topic Guide
GOAL. Demonstrate an understanding of Cherry Point and ATC NATOPS specific
procedures.
REQUIREMENT. Describe the procedures listed in the reference.
INSTRUCTOR. BI.
REFERENCE
1. NKT Facility Manual
1-104 Facility Directives and Memos
1-401 Drug and Alcohol Use
1-402 Facility Parking
1-403 Headsets
1-404 Mail
1-405 Locker Assignments
1-408 Facility Tours
1-409 Airfield Tours
1-410 Phone Usage
1-411 Blood Donations
1-412 Airfield Hours of Operation
1-413 ATCFO and Staff Working Hours
1-414 ATC Watch Bill
1-415 Holiday Manning
1-416 Additional Duties
1-417 Briefing Area
1-418 Operational Crew Briefings
1-419 Leave and Liberty
1-420 Uniforms
1-421 Annual Physicals
1-423 Food and Drink in the Facility
1-424 Portable Electronic Device Usage
1-425 Procedure Evaluation Board (PEB)
1-426 Procedure Evaluation Program (PEP)
2-100 Marines Checking In
2. NAVAIR 00-80T-114
1.3 Control Authority
Chap 2 Air Traffic Control NATOPS Program
3.2 Annual Awards
4.1.6 Facility Directives
4.2.2 Position Logs
4.2.3 Operating Initials
4.3.4.3 Physical Qualification and Examination
4.4.3 Watch Team Briefing
4.4.7.7 Portable Electronic Device Usage
Local Qualification Standards
KNOWLEDGE. Pass a written examination encompassing the requirement with a
minimum score of 80%.
SKILLS AND ABILITIES. NA
Individual has satisfactorily completed all LQS requirements for ORNT 1:
Date: _____________
Trainee: ___________________________ Signature: ________________________
FWO/Crew Chief Signature _______________________________
ORNT 2 – ATC KNOWLEDGE/TRAINING PROGRAM (ACAD-0500)
Lesson Topic Guide
GOAL. Comprehend general ATC knowledge.
REQUIREMENT. Describe the information listed in the reference.
INSTRUCTOR. BI.
REFERENCE
1. FAA JO 7110.65
1-1-1 Purpose of this Order
1−2−1 Word Meanings
1−2−2 Course Definitions
1−2−3 Notes
1−2−4 References
1−2−5 Annotations
1−2−6 Abbreviations
2-1-1 ATC Service
2-1-2 Duty Priority
2-1-3 Procedural Preference
2-1-4 Operational Priority
2-2-1 Recording Information
2-2-2 Forwarding Information
2-2-3 Forwarding VFR Data
2-2-4 Military DVFR Departures
2-2-5 IFR to VFR Flight Plan Change
2-2-6 IFR Flight Progress Data
2-2-7 Manual Input of Computer-assigned Beacon Codes
2-2-8 ALTRV Information
2-2-9 Computer Message Verification
2-2-10 Transmit Proposed Flight Plan
2-2-11 Forwarding Amended and UTM Data
2-2-12 Airborne Military Flights
2-2-13 Forwarding Flight Plan Data Between U.S. and Canadian
2-2-14 Teletype Flight Data Format
2-2-15 North American Route Program Information
2-10-1 En Route Sector Team Position Responsibilities
2-10-2 Terminal Radar/Nonradar Team Position Responsibilities
2-10-3 Tower Team Position Responsibilities
3-1-13 Establishing Two Way Communications
2. NAVAIR 00-80T-114
7.1 General
7.1.1 Purpose
7.1.2 Training Chief
7.1.3 OJTI
7.1.4 ATC Training Team
7.2 Facility Training Program
7.2.1 Program Elements
7.2.2 Program Tools
7.4 Controller Currency and Proficiency
7.4.1 Program Compliance
7.4.2 Definitions
7.4.3 Currency Requirements
7.3 Controller Performance Evaluations
7.3.1 Documentation Requirements
7.5 MACCS Performance Records (MPR)
7.5.1 General
7.5.2 Development and Issuance
7.5.3 Transfer and Retention
7.5.4 Marine Sierra Hotel Aviation Readiness Program (M-SHARP)
7.5.5 Initial MOS and Skill Designators
7.6 MACCS Training and Readiness
3. ATC Facility Manual
4-100 General
4-101 ATCFO Responsibilities
4-103 Training Chief Responsibilities
4-104 FWO Responsibilities
4-105 OJTI Responsibilities
4-106 Trainee Responsibilities
4-107 Local Qualification Standards
4-108 Lesson Topic Guides
4-109 Testing
4-110 Annual Training Plan
4-200 Qualifications Training
4-201 Proficiency Training
4-202 Requalification
4-203 Currency Requirements
4-204 Position Evaluations (ANNUAL SKILL CHECK)
4-205 Tower Visibility Observers
4-300 General
4-301 Definitions
4-302 Facility Training Requirements
4-303 Minimum OJT Position Time
4-304 Selection, Qualification and Evaluation of OJTIs
4-305 Training Teams
4-306 Training Plan
4-307 Lesson Format
4-308 Performance Skill Check (Trainee)
4-309 Performance Skill Check (Qualified)
4-310 Skill Enhancement Training (Trainee)
4-311 Qualification Skill Check
4-312 Examiners
4-313 Additional OJT
4-314 Tape Talk Program
4-315 OJT and Qualification Process Flowchart
4-316 GCA IFR Training
4-317 Designation
4-400 MACCS Performance Record
4-401 LQS/LTG and T&R Events
4-403 Responsibilities
4-404 Position Evaluations
4-405 Disposition of Records and Reports
4-406 Operating Initials
4-500 General
4-503 NAVAIR 755 Progression
4-504 T&R Supplements
4-603 Controller Evaluation Board
4-604 Suspension of Training
4-605 Discontinuation of Training
4-700 General
4-701 IPART
4-702 AT COACH (STARS)
4-703 Tower Simulator
4-704 Simulator Position Logs
4-705 Simulator Training Requirements
App G Instructions For Completing Position Evaluations
App E Guide for Position Logs
Local Qualification Standards
KNOWLEDGE. Pass a written examination encompassing the requirement with a
minimum score of 80%.
SKILLS AND ABILITIES. NA
Individual has satisfactorily completed all LQS requirements for ORNT 2:
Date: _____________
Trainee: ___________________________ Signature: ________________________
FWO/Crew Chief Signature _______________________________
ORNT 3 – ATC TERMINOLOGY (ACAD-0501)
Lesson Topic Guide
GOAL. Comprehend general ATC terminology.
REQUIREMENT. Describe the items listed in the reference.
INSTRUCTOR. BI.
REFERENCE
1. FAA JO 7110.65 - Glossary Terms
Additional Services Advisory Frequency
Aerial Refueling Affirmative
Roger Wilco
Aircraft Classes AIRMET
Approach Gate Final Approach Fix
Final Approach Course Decision Height
Overhead Maneuver Pilot’s Discretion
Pilot Weather Report Preferential Routes
Procedure Turn Segments of Approach Procedure
Short Range Clearances Simulated Flameout
Missed Approach Tower EnRoute Control Service
Information Request Instrument Instrument Meteorological Conditions
Visual Meteorological Conditions Approach Control Service
Expect Departure Clearance Time ATC Assigned Airspace
Instrument Approach Procedure Radar Separation
Nonradar Separation Traffic Management Unit
Traffic Pattern Vector
2. ATC Facility Manual
1-200 Word Meanings
1-201 Annotations
1-202 Abbreviations
Precision Approach Radar Explosive Ordnance Disposal
Unmanned Aerial System Airport Surveillance Radar
Combat Aircraft Loading Area Information Request
1-203 Glossary
1-204 Position Relief Checklist
Local Qualification Standards
KNOWLEDGE. Pass a written examination encompassing the requirement with a
minimum score of 80%.
SKILLS AND ABILITIES. NA
Individual has satisfactorily completed all LQS requirements for ORNT 3:
Date: _____________
Trainee: ___________________________ Signature: ________________________
FWO/Crew Chief Signature _______________________________
ORNT 4 – AIRFIELD LAYOUT (ACAD-0502)
Lesson Topic Guide
GOAL. Comprehend the airfield layout.
REQUIREMENT. Given an airfield diagram, draw/label required information.
INSTRUCTOR. BI.
REFERENCE
1. Memorize the airfield layout. Draw/label from memory an airfield diagram
to include:
a. Runways.
Numbering/marking.
Length and width.
Crash Fire Rescue standby positions.
Location of Windsocks.
Location of Optical landing systems.
Carrier Deck
Harrier Pads
b. Helicopter landing areas/spots.
Name/designation.
c. Taxiways.
Designation (name/number).
Special use areas (hazardous cargo, hot brakes, ordnance Load/
offload, arm/dearm, etc).
d. Fuel Pits.
Number of fueling points.
e. Aircraft wash racks.
f. Tenant aircraft parking ramps.
Squadron assigned.
g. Transient parking ramps.
VIP spots.
h. Crash Fire Rescue.
Location of building and hotspots.
i. Hangars.
Unit assigned.
j. Visual aids.
Runway lights.
Approach lights.
Taxiway lights.
Airfield beacon.
Obstruction lights.
k. Navigation aids.
TACAN Checkpoints
Compass rose.
l. Obstructions on the airfield: Type, height, and location.
m. ATC radar types and location.
2. Facility Manual
5-100 General
3. Airfield Operations Manual
1.1. General Prudential Rules
1.2. Definitions
1.3. Airfield Description
1.4. Hours of Operation
1.5. Hangar and Service Facilities
1.6. Prior Permission Required (PPR)
6.4. Distinguished Visitor (DV) Procedures
Local Qualification Standards
KNOWLEDGE. Pass a written examination encompassing the requirement with a
minimum score of 80%.
SKILLS AND ABILITIES. NA
Individual has satisfactorily completed all LQS requirements for ORNT 4:
Date: _____________
Trainee: ___________________________ Signature: ________________________
FWO/Crew Chief Signature _______________________________
ORNT 5 – LOCAL AREA/AIRFIELD SPECIFIC INFORMATION (ACAD-0503)
Lesson Topic Guide
GOAL. Comprehend local area/airfield specific information.
REQUIREMENT. Conduct the following as described in the reference.
1. Describe when arresting system operations are in affect.
2. Describe the guidelines for runway selection.
3. Describe local airfield weather minimums.
4. List aircraft type, modex, and tactical callsigns of each tenant squadron.
5. Describe local traffic patterns and no-fly areas.
6. List alternate, divert, and adjacent airfields.
7. List local frequencies pertinent to air traffic or safety of flight.
INSTRUCTOR. BI.
REFERENCE
1. FAA JO 7110.65
3-3-6 Arresting System Operation
3-5-1 Runway Selection
2. Local publications
Airfield Weather Minimums
Type Aircraft Assigned Each Local Squadron (FacMan 2-600)
Modex/Tactical Call of Each Local Squadron (FacMan 2-600)
Traffic Patterns and no fly areas (FacMan 6-303)
Alternate/Divert Airfield
Adjacent Airfields
Airport Surface Area Description (FacMan 2-610)
Facility Frequencies (FacMan 2-608)
3. ATC Facility Manual
2-200 Organization
2-201 Purpose and Mission
2-202 Tasks
2-204 Civilian Employee/Bargaining Unit Information
4. Airfield Operations Manual
2.2. Flight Planning
2.4. Weather Minimums
2.6. Stereo Route/Pre-filed Flight Plans
2.8. Shipboard Operations
2.9. Customs and Agriculture Inspections
3.1. General
3.2. Noise Abatement Procedures
3.10. Helicopter/Tiltrotor Operating Procedures
3.20. Hot Brakes
4.8. Bird/Animal Aircraft Strike Hazard (BASH) and Wildlife
5.1. Air Traffic Control Facility (ATCF)
5.5. Local Operating Terms
6.2. Passenger Manifesting
Local Qualification Standards
KNOWLEDGE. Pass a written examination encompassing the requirement with a
minimum score of 80%.
SKILLS AND ABILITIES. NA
Individual has satisfactorily completed all LQS requirements for ORNT 5:
Date: _____________
Trainee: ___________________________ Signature: ________________________
FWO/Crew Chief Signature _______________________________
ORNT 6 – ATC FACILITY EMERGENCY/SAFETY EQUIPMENT (ACAD-0504)
Lesson Topic Guide
GOAL. Comprehend location of ATC Facility Emergency/Safety equipment.
REQUIREMENT. Given a diagram, label the following as described in the
reference.
1. Location(s) of all fire extinguishers.
2. Location(s) of the main power circuit breaker.
3. Location(s) of the Fire Bill.
4. Location(s) of the evacuation route.
INSTRUCTOR. BI.
REFERENCE
1. Facility Manual
3-100 General
3-101 Electrical Shock Hazard
3-102 Fire Bill
3-103 Cleanliness
3-104 Elevator Outage
3-105 Cypher Locks
3-106 Fire Extinguishers
3-107 Fire Alarms
3-201 Bomb Threats
3-203 Access Areas
5-706 Control Tower Emergency Evacuation Plan
2. Facility Safety Orientation. Conduct a safety orientation with your
crew.
a. Locations of all fire extinguishers.
b. Locations of main power circuit breaker.
c. Locations of the Fire Bill.
d. Emergency evacuation routes.
Local Qualification Standards
KNOWLEDGE. Pass a written examination encompassing the requirement with a
minimum score of 80%.
SKILLS AND ABILITIES. NA
Individual has satisfactorily completed all LQS requirements for ORNT 6:
Date: _____________
Trainee: ___________________________ Signature: ________________________
FWO/Crew Chief Signature _______________________________
ORNT 7 – EMERGENCY PROCEDURES AND POLICIES (ACAD-0505)
Lesson Topic Guide
GOAL. Comprehend ATC emergency procedures and policies.
REQUIREMENT. Describe the items listed in the reference.
INSTRUCTOR. BI.
REFERENCE
1. FAA JO 7110.65
2-1-7 In-flight Equipment Malfunctions
2-1-8 Minimum Fuel
4-7-8 Below Minima Report by Pilot
5-2-7 Emergency Code Assignment
Ch10 Sec1 (Emergencies) General
Ch10 Sec2 Emergency Assistance
Ch10 Sec3 Overdue Aircraft
Ch10 Sec4 Control Actions
2. NAVAIR 00-80T-114
4.4 Facility Operation
4.4.1 Hours of Operation
4.4.2 Watch Team Briefing
4.4.3 Time Standards
4.4.4 Emergency Plan
4.4.5 Emergency Power
4.4.6 Communications
4.4.7 Recorders
4.4.8 Automatic Terminal Information Service (ATIS)
4.6 Security of Facilities
4.6.1 Controlled Access
4.6.2 Official Business Access to Other Than ATC Personnel
4.6.3 Unofficial Visits and Tours
4.6.4 Commercial Telephones
4.7 Incidents, Mishaps and Hazards
4.7.1 General
4.7.2 Guidance Concerning Investigation and Reporting
4.7.3 Post Incident, Mishap and Hazard Procedures
4.8 ATC Hazard Reports
3. Facility Manual
5-700 General
5-701 Information Requirements
5-702 Emergency Notification
6-700 General
6-701 Information Requirements
6-702 Emergency Notification
4. Airfield Operations Manual
2.11. Overdue Aircraft Procedures
5.2. Emergency Procedures
Local Qualification Standards
KNOWLEDGE. Pass a written examination encompassing the requirement with a
minimum score of 80%.
SKILLS AND ABILITIES. NA
Individual has satisfactorily completed all LQS requirements for ORNT 7:
Date: _____________
Trainee: ___________________________ Signature: ________________________
FWO/Crew Chief Signature _______________________________
ORNT 8 – SPECIAL FLIGHTS (ACAD-0506)
Lesson Topic Guide
GOAL. Comprehend the handling of special flights, procedures and policies.
REQUIREMENT. Describe the items listed in the reference.
INSTRUCTOR. BI.
REFERENCE
1. FAA JO 7110.65
9-1-3 Flight Check Aircraft
9-2-1 Aircraft Carrying Dangerous Materials
9-2-7 IFR Military Training Routes
9-2-14 Military Aerial Refueling
Local Qualification Standards
KNOWLEDGE. Pass a written examination encompassing the requirement with a
minimum score of 80%.
SKILLS AND ABILITIES. NA
Individual has satisfactorily completed all LQS requirements for ORNT 8:
Date: _____________
Trainee: ___________________________ Signature: ________________________
FWO/Crew Chief Signature _______________________________
ORNT 9 – WEATHER (ACAD-0507)
Lesson Topic Guide
GOAL. Comprehend basic weather knowledge.
REQUIREMENT. Describe the items listed in the reference.
INSTRUCTOR. BI.
REFERENCE
1. FAA JO 7110.65
2-6-2 PIREP Solicitation and Dissemination
2-6-3 Reporting Weather Conditions
2-6-4 Issuing Weather and Chaff Areas
2-6-5 Disseminating Official Weather Information
2-6-6 Hazardous Inflight Weather Advisory Service (HIWAS)
2-7-1 Current Settings
2-7-2 Altimeter Setting Issuance Below Lowest Usable FL
2−8−1 Furnish RVR/RVV Values
2−8−2 Arrival/Departure Runway Visibility
2−8−3 Terminology
2−9−1 Application (ATIS)
2−9−2 Operating Procedures
2−9−3 Content
3-3-4 Braking Action
3-3-5 Braking Action Advisories
2. NAVAIR 00-80T-114
9.3 Weather Observations by Control Tower Personnel
9.3.1 General
9.3.2 Certification of Tower Visibility Observers
9.3.3 Tower Visibility Charts
3. Facility Manual
6-333 Precipitation Intensity
B-102 Weather Definitions
B-104 Weather Advisories & Warnings
B-105 Thunderstorm Conditions
B-201 Sequence Elements
Local Qualification Standards
KNOWLEDGE. Pass a written examination encompassing the requirement with a
minimum score of 80%.
SKILLS AND ABILITIES. NA
Individual has satisfactorily completed all LQS requirements for ORNT 9:
Date: _____________
Trainee: ___________________________ Signature: ________________________
FWO/Crew Chief Signature _______________________________
ORNT 10 – LETTERS OF AGREEMENT (ACAD-0508)
Lesson Topic Guide
GOAL. Comprehend information contained in local Letters of Agreement.
REQUIREMENT. Given the reference material, identify the key information
contained.
INSTRUCTOR. BI.
REFERENCE
1. Letters of Agreement.
a. Washington Center.
ZDC and NKT Approach Control Service
ZDC and NKT and NCA Approach Control Services
ZDC and NKT Use of NEUSE ATCAA
ZDC and NKT and NVF HAT B ATCAA
ZDC and NKT Use of BURNER ATCAA
ZDC and NKT and NVF Restricted Areas and MOAs
ZDC and NKT and 4thFW and NVF Phelps MOA and R-5314
ZDC and 4thFW and NKT and NVF RAZOR TALON LFE
ZDC and ILM and NKT and 4thOG IR-012 Procedures
ZDC and MCABE and 2D MAW Stereo Plans for MAG14
ZDC and MAG14 and NKT Stereo Plans
b. Adjacent Facilities.
NKT and GSB Tower Enroute Control
ILM and NKT and NCA Approach Control Services
NVF and NKT Control and Coordination
NVF and NKT and CSFWL SELFEX Procedures
NKT and NTU Approach Control Services
NKT and ORF Tower Approach Control Services
NKT and NJM and RMD Bogue Operating Procedures
NKT and Big Rock and Blackburn Real Time Joint Use
NKT and NCA Radar Feeds
EWN and NKT Control and Coordination
NKT and EWN and Hubert Tolson Aerobatic Practice Area
NKT and MAG14 and MACG 28 Time Share – ATNAVICS
c. Special Operations.
MARSOC and NCA and NKT Stone Bay UAS Procedures
NKT and MAG14 UAS Procedures
NKT and 2dMAW and USAF BURNER ATCAA
NKT and NVF and CCG-4 and C2F Haystack and Croatan One
NKT and Dogwood Farm Aircraft Operations
NKT and VAW120 Practice Precautionary Approaches
NKT and 16 SOS/DO AC-130 Hot Guns
VX-20 and NKT (MOA) Triton UAS Procedures
NKT and NCA and Duke Life Flight IFR Procedures
NKT and 2dMAW and USAF NEUSE ATCAAs
Local Qualification Standards
KNOWLEDGE. Pass a written examination encompassing the requirement with a
minimum score of 80%.
SKILLS AND ABILITIES. NA
Individual has satisfactorily completed all LQS requirements for ORNT 10:
Date: _____________
Trainee: ___________________________ Signature: ________________________
FWO/Crew Chief Signature _______________________________
ORNT 11 – ATC PUBLICATIONS/FORMS (ACAD-0509)
Lesson Topic Guide
GOAL. Comprehend knowledge of ATC publications.
REQUIREMENT. Given the reference material, identify the key information
contained.
INSTRUCTOR. BI.
REFERENCE
1. FAA 7220.1 Operational Position Standards
2. FAA JO 7110.65 Air Traffic Control
3. FAA JO 7210.3 Facility Operations
4. FAA JO 7340.1 Contractions Directive
5. 14 CFR Part 91 General Operating
6. AIM Airman's Information Directive
7. AOM Airfield Operations Manual
8. ATC Facility Manual
2-700 General
2-701 Training Branch Library
2-702 Tower Branch Library
2-703 Radar Branch Library
2-704 Electronic Library
2-706 Publications Control
2-707 Publications Available
5-400 General
5-402 AOM Topics
6-100 General
6-300 General
6-301 AOM Topics
9. IFR Supplement
10. VFR Supplement
11. NOTAMS General Notices
12. AP1B Military Training Routes
13. Local Sectional (Charlotte)
14. NAVAIR 00-80T-114
1.4.2 Federal Aviation Administration Documents
1.4.3 Department of the Navy Directives
1.4.5 Other Relevant Publications
15. Low Altitude United States.
16. High Altitude United States.
17. ATC Facility Manual Forms.
1-100 Purpose
2-300 General
2-301 SUA Violation
2-302 Control Tower Crash Emergency Call Sheet
2-303 Operational Discrepancy
2-304 Air Traffic Activity Reports
2-305 Class Roster
2-306 Facility Recommendation
2-307 FWO Checklist
2-308 SUA Activation Logs
2-309 Tower Visibility Log
2-310 Vehicle Operator’s Certificate
2-311 Electronic Library Log
2-312 AVOC Attendance Roster
2-313 GCA Run Log
2-314 Position Evaluations
2-315 Air Traffic Control Specialist Certificate
2-316 Daily Record of Facility Operation
2-317 Position Log
2-318 Initial Incident Reporting
2-319 Daily Flight Schedules and Air Flow
2-320 Airfield Activities
2-321 Weekly Training Report
2-322 Monthly Training Report
2-323 Annual Training Report
2-324 MCIEAST Monthly Report
2-325 MCIEAST Quarterly SITREP
2-326 MCIEAST NATOPS Evaluation
2-327 Internal NATOPS Evaluation
2-328 ASRS
2-329 Annual Skill Checks
Local Qualification Standards
KNOWLEDGE. Pass a written examination encompassing the requirement with a
minimum score of 80%.
SKILLS AND ABILITIES. NA
Individual has satisfactorily completed all LQS requirements for ORNT 11:
Date: _____________
Trainee: ___________________________ Signature: ________________________
FWO/Crew Chief Signature _______________________________
Section III RADAR FLIGHT DATA
LTG 1 - RADIO AND INTERPHONE COMMUNICATIONS (ACAD-0520)
Lesson Topic Guide
GOAL. Describe radio and interphone communications knowledge.
REQUIREMENT.
1. Describe radios and interphone communications.
INSTRUCTOR. BI.
REFERENCE
1. FAA JO 7110.65
2-4-1 Radio Communications
2-4-2 Monitoring
2-4-14 Words and Phrases
2-4-15 Emphasis for Clarity
2-4-16 ICAO Phonetics
2-4-17 Numbers Usage
2-4-18 Number Clarification
2-4-19 Facility Identification
2-4-20 Aircraft Identification
2-4-21 Description of Aircraft Types
2-4-22 Airspace Classes
Local Qualification Standards
KNOWLEDGE. Pass a written examination encompassing the requirement with a
minimum score of 80%.
SKILLS AND ABILITIES
Skill/Ability Date OJTI
Demonstrate the ability to monitor interphones and
assigned radio frequencies continuously.
Demonstrate the skill of using the word “heavy” as
part of the identification of heavy aircraft.
Demonstrate the ability to use ICAO pronunciation
of numbers and letters.
Demonstrate the skill to state numbers properly for
altitudes, flight levels, time, altimeter, speed,
wind, headings, beacon codes, runways and
frequencies.
Demonstrate the skill to use proper aircraft
identification.
Individual has satisfactorily completed all LQS requirements for LTG 1:
Date: _____________
Trainee: ___________________________ Signature: ________________________
FWO/Crew Chief Signature _______________________________
LTG 2 - AIRCRAFT MOVEMENT DATA (ACAD-0521)
Lesson Topic Guide
GOAL. Describe aircraft movement data knowledge.
REQUIREMENT.
1. Describe the terms of acknowledgement of clearances and instructions.
2. Describe interphone transmission priorities.
3. Describe the terms for priority interruption.
4. Describe the interphone format.
INSTRUCTOR. BI.
REFERENCE
1. FAA JO 7110.65
2-4-3 Pilot Acknowledgement/Read Back
2-4-4 Authorized Interruptions
2-4-5 Authorized Transmissions
2-4-6 False or Deceptive Communications
2-4-7 Authorized Relays
2-4-8 Radio Message Format
2-4-9 Abbreviated Transmissions
2-4-10 Interphone Transmission Priorities
2-4-11 Priority Interruption
2-4-12 Interphone Message Format
2-4-13 Interphone Message Termination
Local Qualification Standards
KNOWLEDGE. Pass a written examination encompassing the requirement with a
minimum score of 80%.
SKILLS AND ABILITIES
Skill/Ability Date OJTI
Demonstrate the ability to communicate using proper
radio message format.
Demonstrate the skill of abbreviating transmissions
after communications have been established.
Demonstrate the ability to terminate interphone
messages with your operating initials.
Demonstrate the ability to use the proper format
for interphone messages.
Demonstrate the skill to properly prioritize
interphone messages.
Demonstrate the ability to interrupt lower priority
messages.
Individual has satisfactorily completed all LQS requirements for LTG 2:
Date: _____________
Trainee: ___________________________ Signature: ________________________
FWO/Crew Chief Signature _______________________________
LTG 3 – FLIGHT PROGRESS STRIPS (ACAD-0522)
Lesson Topic Guide
GOAL. Describe flight progress strip knowledge.
REQUIREMENT
1. Describe the methods for updating information on flight progress strips.
2. Label flight progress strips, to include:
a. Arrivals.
b. Departures.
c. Overflights.
d. Enroute aircraft.
3. List aircraft prefixes.
4. List aircraft suffixes.
5. List flight progress strip control information symbols.
INSTRUCTOR. BI.
REFERENCE
1. FAA JO 7110.65
2-3-1 General
2-3-4 Terminal Data Entries
2-3-5 Aircraft Identity
2-3-6 Aircraft Type
2-3-7 USAF/USN Undergraduate Pilots
2-3-8 Aircraft Equipment Suffix
2-3-10 Control Symbology
Local Qualification Standards
KNOWLEDGE. Pass a written examination encompassing the requirement with a
minimum score of 80%.
SKILLS AND ABILITIES
Skill/Ability Date OJTI
Demonstrate the ability to identify civil and
military aircraft using call sign prefixes.
Demonstrate the skill to properly complete flight
progress strips.
Demonstrate the ability to properly forward
aircraft equipment suffixes.
Demonstrate the ability to use the proper code for
test flight plans.
Demonstrate the skill to post flight progress
strips and data to the appropriate position.
Demonstrate the ability to write a manual copy with
return strip and enter them correctly into the
STARS display.
Demonstrate the ability to identify what
information goes in each block of a flight progress
strip for both arrivals and departures.
Demonstrate the ability to record a pointout from
an adjacent facility.
Individual has satisfactorily completed all LQS requirements for LTG 3:
Date: _____________
Trainee: ___________________________ Signature: ________________________
FWO/Crew Chief Signature _______________________________
LTG 4 – ATC CLEARANCE/PHRASEOLOGY (ACAD-0523)
Lesson Topic Guide
GOAL. Describe ATC clearance knowledge and phraseology.
REQUIREMENT
1. Identify the clearance items.
2. Describe how to relay clearances.
3. Describe the phraseology to issue route and altitudes amendments.
4. Describe the phraseology to issue a through clearance.
5. Describe the phraseology to issue an altitude reservation (ALTRV)
clearance.
INSTRUCTOR. BI.
REFERENCE
1. FAA JO 7110.65
4-2-1 Clearance Items
4-2-4 Clearance Relay
4-2-5 Route and Altitude Amendments
4-2-6 Through Clearances
4-2-7 ALTRV Clearance
4-2-8 IFR-VFR and VFR-IFR Flights
4-5-2 Flight Direction
4-5-4 Lowest Usable Flight Level
Local Qualification Standards
KNOWLEDGE. Pass a written examination encompassing the requirement with a
minimum score of 80%.
SKILLS AND ABILITIES.
Skill/Ability Date OJTI
Individual has satisfactorily completed all LQS requirements for LTG 4:
Date: _____________
Trainee: ___________________________ Signature: ________________________
FWO/Crew Chief Signature _______________________________
LTG 13 – RADAR EQUIPMENT PRINCIPLES (ACAD-0532)
Lesson Topic Guide
GOAL. Identify radar equipment usage.
REQUIREMENT. Identify radar equipment principles, to include the following:
1. Presentation and equipment performance.
2. Alignment accuracy check.
3. Radar use.
4. Beacon range accuracy.
5. Electronic cursor.
6. Altitude filters.
7. Standby/low sensitivity operation.
8. Inoperative interrogator.
9. In-flight deviations from transponder.
10. Automated Radar Terminal Systems (ARTS)–Terminal.
11. TPX-42–Terminal.
12. Facility equipment general.
13. Radar use.
14. Video maps.
15. Airport facilities.
16. Radar operations equipment.
17. Precision approach landing system approach criteria.
18. Facility equipment.
INSTRUCTOR. BI.
REFERENCE
1. FAA JO 7110.65
5-1-1 Presentation and Equipment Performance
5-1-2 Alignment Accuracy Check
5-1-3 ATC Surveillance Source Use
5-1-4 Beacon Range Accuracy
5-1-7 Electronic Cursor
5-2-13 Standby or Low Sensitivity Operation
5-2-16 Inoperative or Malfunctioning Interrogator
5-2-21 Automatic Altitude Reporting
5-2-22 Inflight Deviations From Transponder Requirements
5-2-23 Beacon Termination
5-2-24 Altitude Filters
5-15-1 Application
5-15-2 Responsibility
5-15-3 Functional Use
5-15-4 System Requirements
5-15-5 Information Displayed
5-15-6 CA/MCI
5-15-7 Inhibiting Minimum Safe Altitude Warning (MSAW)
5-15-8 Track Suspend Function
2. FAA JO 7210.3
Ch3 Sec1 (Facility Equipment) General
Ch3 Sec7 Radar Use
Ch3 Sec8 Video Maps
3. NAVAIR 00-80T-114
3.5 Airport Facilities
10.2.1 Equipment Requirements
App S Precision Approach Landing System Approach Criteria
Local Qualification Standards
KNOWLEDGE. Pass a written examination encompassing the requirement with a
minimum score of 80%.
SKILLS AND ABILITIES. Will be evaluated during LTG 23 and LTG 24.
Individual has satisfactorily completed all LQS requirements for LTG 13:
Date: _____________
Trainee: ___________________________ Signature: ________________________
FWO/Crew Chief Signature _______________________________
LTG 15 – BASIC RADAR (ACAD-0534)
Lesson Topic Guide
GOAL. Describe basic radar knowledge.
REQUIREMENT. Describe the following IAW the reference:
1. Formation flights.
2. Wake turbulence.
3. Wake turbulence cautionary advisories.
4. Observed abnormalities.
5. Landing area condition.
6. Timely information.
7. Traffic advisories.
8. Bird activity information.
9. Traffic information.
10. Altitude restricted approach.
11. Vertical separation minima.
12. Single frequency approaches (SFA).
13. Clearance relay.
14. Transfer of radar identification.
15. Circling approach.
16. Radar identification.
17. Radar separation.
18. Radar arrivals.
INSTRUCTOR. BI
REFERENCE
1. FAA JO 7110.65
2-1-13 Formation Flights
2-1-15 Control Transfer
2-1-19 Wake Turbulence
2-1-20 Wake Turbulence Cautionary Advisories
2-1-21 Traffic Advisories
2-1-22 Unmanned Aircraft System (UAS) Activity Information
2-1-23 Bird Activity Information
2-2-5 IFR to VFR Flight Plan Change
3-1-6 Traffic Information
3-1-10 Observed Abnormalities
3-3-1 Landing Area Conditions
3-3-3 Timely Information
3-10-10 Altitude Restricted Approach
4-5-1 Vertical Separation Minima
4-7-3 Single Frequency Approaches (SFA)
4-8-6 Circling Approach
4-8-8 Communications Release
5-3-1 Application
5-3-2 Primary Radar Identification Methods
5-3-3 Beacon Identification Methods
5-3-5 Questionable Identification
5-4-1 Application
5-4-3 Methods (Transfer of Radar ID)
5-4-4 Traffic (Radar Separation)
5-4-5 Transferring Controller Handoff
5-5-1 Application (Radar Separation)
5-5-2 Target Separation
5-5-4 Minima (Radar Separation)
5-5-8 Additional Separation For Formation Flights
5-9-1 Vectors to Final Approach Course
5-9-2 Final Approach Course Interception
5-9-3 Vectors Across Final Approach Coarse
5-9-4 Arrival Instructions
5-9-5 Approach Separation Responsibility
10-2-8 Radar Assistance to VFR Aircraft in Weather Difficulty
Local Qualification Standards
KNOWLEDGE. Pass a written examination encompassing the requirement with a
minimum score of 80%.
SKILLS AND ABILITIES. Will be evaluated on Radar Final Control.
Individual has satisfactorily completed all LQS requirements for LTG 15:
Date: _____________
Trainee: ___________________________ Signature: ________________________
FWO/Crew Chief Signature _______________________________
LTG 19 – RADAR COORDINATION (ACAD-0538)
Lesson Topic Guide
GOAL. Describe radar coordination procedures.
REQUIREMENT. Describe the following IAW the reference:
1. Radio and interphone communication monitoring.
2. Authorized interruptions.
3. Authorized relays.
4. Clearance prefix.
5. Departure clearances.
6. Abbreviated departure clearance.
7. Delay sequencing.
8. Delays.
9. Forward departure delay info.
10. Coordination with receiving facility.
11. Forwarding departure times.
INSTRUCTOR. BI.
REFERENCE
1. FAA JO 7110.65
2-1-14 Coordinate Use of Airspace
4-2-2 Clearance Prefix
4-3-2 Departure Clearances
4-3-3 Abbreviated Departure Clearance
4-3-6 Delay Sequencing
4-3-7 Forward Departure Delay Information
4-3-8 Coordination With Receiving Facility
4-3-10 Forwarding Departure Times
4-6-3 Delays
Local Qualification Standards
KNOWLEDGE. Pass a written examination encompassing the requirement with a
minimum score of 80%.
SKILLS AND ABILITIES
Skill/Ability Date OJTI
Demonstrate the ability to coordinate Special Use
Airspace Activity information with adjacent
facilities.
Demonstrate the skill to maintain current
information on all status boards.
Individual has satisfactorily completed all LQS requirements for LTG 19:
Date: _____________
Trainee: ___________________________ Signature: ________________________
FWO/Crew Chief Signature _______________________________
LTG 23 – RADAR EQUIPMENT (EQPT-2018)
Lesson Topic Guide
GOAL. Operate Radar Equipment.
REQUIREMENT. Given the required equipment, conduct the following:
1. Configure the ASR scope for daily operations.
2. Configure PAR for daily operations.
3. Ensure transmitter/receiver control panels are functional.
4. Use intercom units to conduct a communications check.
5. Read altimeter, wind instruments, and clock information.
6. Ensure NAVAID monitors are operating properly, read indicators, and
identify equipment status.
7. Navigate through different screens in the VIDS.
8. Operate the weather reporting monitor to extract information.
9. Operate the VISCOM
10. Perform alignment checks.
11. Operate the Emergency Communications System (ECS).
INSTRUCTOR. BI
PREREQUISITE. ACAD-0532
Local Qualification Standards
KNOWLEDGE. Pass a written examination encompassing the requirement with a
minimum score of 80%.
SKILLS AND ABILITIES. Demonstrate the proper operation of the following with
no assistance from the instructor.
Skill/Ability Date OJTI
Demonstrate the ability to read altimeter, wind
instruments and clock information.
Demonstrate the ability to configure the ASR scope
for an approach.
Demonstrate the ability to configure the PAR scope
to the correct runway.
Demonstrate the skill to perform an alignment check
on the PAR scope.
Demonstrate the ability to relay weather
information.
Demonstrate the skill of navigating through
different menus and screens on the VIDS.
Demonstrate the ability to operate the VISCOM
correctly.
Individual has satisfactorily completed all LQS requirements for LTG 23:
Date: _____________
Trainee: ___________________________ Signature: ________________________
FWO/Crew Chief Signature _______________________________
LTG 24 – RADAR FLIGHT DATA EQUIPMENT (EQPT-2019)
Lesson Topic Guide
GOAL. Operate Radar Flight Data (RD) equipment.
REQUIREMENT. Given the required RD equipment, conduct the following:
1. Use telephones.
2. Operate FDIO to include:
Input flight plans
Amend flight plans
Weather report
General information message
Hold message
Departure message
Progress report
ARTS force flight progress data
Restore database
Stereo flight plan
Input station altimeter
Remove flight plan
3. Radar Displays.
4. Personal computer.
5. Wind Indicators.
6. Altimeter Readout.
7. Clocks.
INSTRUCTOR. BI
PREREQUISITE. None.
Local Qualification Standards
KNOWLEDGE. This event is completed through practical application.
SKILLS AND ABILITIES
Skill/Ability Date OJTI
Demonstrate the use of telephones.
Demonstrate the ability to input the following using the FDIO equipment.
Flight Plan – FP
Amendment Message – AM
Departure Message – DM
Flight Plan Readout – FR
General Information – GI
Hold Message – HM
Progress Report – PR
Restore Database – RB
ARTS Force – RF
Remove Strip – RS
Stereo Flight Plan – SP
Strip Request – SR
Test Device – TD
Weather Request- WR
Demonstrate the skill to load blank strips into the
FDIO printer.
Individual has satisfactorily completed all LQS requirements for LTG 24:
Date: _____________
Trainee: ___________________________ Signature: ________________________
FWO/Crew Chief Signature _______________________________
LTG 25 – RADAR COMMUNICATIONS EQUIPMENT (COMM-2206)
Lesson Topic Guide
GOAL. Operate ATC communications equipment.
REQUIREMENT. While in a RATCF, operate the following communications
equipment:
1. Transmitter/receiver control panel(s).
2. Backup/emergency transmitter/receiver location and controls.
3. Emergency communications system (ECS).
4. Crash Phone
5. Intercom units.
6. Telephones.
7. VIDS.
INSTRUCTOR. BI.
PREREQUISITE. None.
Local Qualification Standards
KNOWLEDGE. Pass a written examination encompassing the requirement with a
minimum score of 80%.
SKILLS AND ABILITIES
Skill/Ability Date OJTI
Demonstrate the ability to call agencies on the
landlines.
Demonstrate the ability to add, modify and delete
status information on the VIDS.
Demonstrate the use of intercom units to conduct a
communications check.
Demonstrate the skill to navigate through different
screens on the VIDS.
Individual has satisfactorily completed all LQS requirements for LTG 25:
Date: _____________
Trainee: ___________________________ Signature: ________________________
FWO/Crew Chief Signature _______________________________
LTG RD26 – LOCAL PROCEDURES
Lesson Topic Guide
GOAL. Describe information contained in local directives.
REQUIREMENT. Given the reference material, identify the key information
contained.
INSTRUCTOR. BI.
REFERENCE
1. Letters of Agreement.
Wilmington Tower and MCAS Cherry Point and MCAS New River
Washington Center and Cherry Point RATCF
FACSFAC VACAPES and MCAS Cherry Point
2. Glossary
Acknowledge
Roger
Say Again
Stand By
Unable
3. Facility Manual
2-603 Location Identifiers
2-605 Interfacility Landlines
2-606 Intrafacility Landlines
2-607 Cherry Point Landline Numbers
2-608 Local Frequencies
2-609 Adjacent Facility Frequencies
6-100 General
6-101 Airspace
6-102 Adjacent Airspace
6-104 Fixes and Airports Within 80 Nautical Miles
6-105 Discrete Beacon Code Assignments
6-200 Terminal Radar Team Positions
6-210 Radar Flight Data
6-304 FDIO Test Flight Plans
6-310 Equipment Status Notification
6-324 Information and Status Boards
6-327 Terminal Data Entries
6-328 Control Symbology
6-330 Strip Marking for Local IFR Clearances
7-102 ETVS
7-110 Tape Recorders
App H Flight Data Input/Output (FDIO) Handbook
4. Airfield Operations Manual
2.3. Instructions for Filing and Completing Flight Plans
5. NAVAIR 00-80T-114
10.1.3.6 Flight Data
Local Qualification Standards
KNOWLEDGE. Pass a written examination encompassing the requirement with a
minimum score of 80%.
SKILLS AND ABILITIES.
Skill/Ability Date OJTI
Individual has satisfactorily completed all LQS requirements for LTG 26:
Date: _____________
Trainee: ___________________________ Signature: ________________________
FWO/Crew Chief Signature _______________________________
Section IV RADAR FINAL CONTROL
LTG 1 - RADIO AND INTERPHONE COMMUNICATIONS (ACAD-0520)
Lesson Topic Guide
GOAL. Describe radio and interphone communications knowledge.
REQUIREMENT.
1. Describe radios and interphone communications.
INSTRUCTOR. BI.
REFERENCE
1. FAA JO 7110.65
2-4-1 Radio Communications
2-4-2 Monitoring
2-4-14 Words and Phrases
2-4-15 Emphasis for Clarity
2-4-16 ICAO Phonetics
2-4-17 Numbers Usage
2-4-18 Number Clarification
2-4-19 Facility Identification
2-4-20 Aircraft Identification
2-4-21 Description of Aircraft Types
2-4-22 Airspace Classes
Local Qualification Standards
KNOWLEDGE. Pass a written examination encompassing the requirement with a
minimum score of 80.
SKILLS AND ABILITIES
Skill/Ability Date OJTI
Demonstrate the ability to monitor interphones and
assigned radio frequencies continuously.
Demonstrate the skill of using the word “heavy” as
part of the identification of heavy aircraft.
Demonstrate the ability to use ICAO pronunciation
of numbers and letters.
Demonstrate the skill to state numbers properly for
altitudes, flight levels, time, altimeter, speed,
wind, headings, beacon codes, runways and
frequencies.
Demonstrate the skill to use proper aircraft
identification.
Individual has satisfactorily completed all LQS requirements for LTG 1:
Date: _____________
Trainee: ___________________________ Signature: ________________________
FWO/Crew Chief Signature _______________________________
LTG 2 - AIRCRAFT MOVEMENT DATA (ACAD-0521)
Lesson Topic Guide
GOAL. Describe aircraft movement data knowledge.
REQUIREMENT.
1. Describe the terms of acknowledgement of clearances and instructions.
2. Describe interphone transmission priorities.
3. Describe the terms for priority interruption.
4. Describe the interphone format.
INSTRUCTOR. BI.
REFERENCE
1. FAA JO 7110.65
2-4-3 Pilot Acknowledgement/Read Back
2-4-4 Authorized Interruptions
2-4-5 Authorized Transmissions
2-4-6 False or Deceptive Communications
2-4-7 Authorized Relays
2-4-8 Radio Message Format
2-4-9 Abbreviated Transmissions
2-4-10 Interphone Transmission Priorities
2-4-11 Priority Interruption
2-4-12 Interphone Message Format
2-4-13 Interphone Message Termination
Local Qualification Standards
KNOWLEDGE. Pass a written examination encompassing the requirement with a
minimum score of 80.
SKILLS AND ABILITIES
Skill/Ability Date OJTI
Demonstrate the ability to communicate using proper
radio message format.
Demonstrate the skill of abbreviating transmissions
after communications have been established.
Demonstrate the ability to terminate interphone
messages with your operating initials.
Demonstrate the ability to use the proper format
for interphone messages.
Demonstrate the skill to properly prioritize
interphone messages.
Demonstrate the ability to interrupt lower priority
messages.
Individual has satisfactorily completed all LQS requirements for LTG 2:
Date: _____________
Trainee: ___________________________ Signature: ________________________
FWO/Crew Chief Signature _______________________________
LTG 3 – FLIGHT PROGRESS STRIPS (ACAD-0522)
Lesson Topic Guide
GOAL. Describe flight progress strip knowledge.
REQUIREMENT
1. Describe the methods for updating information on flight progress strips.
2. Label flight progress strips, to include:
a. Arrivals.
b. Departures.
c. Overflights.
d. Enroute aircraft.
3. List aircraft prefixes.
4. List aircraft suffixes.
5. List flight progress strip control information symbols.
INSTRUCTOR. BI.
REFERENCE
1. FAA JO 7110.65
2-3-1 General
2-3-4 Terminal Data Entries
2-3-5 Aircraft Identity
2-3-6 Aircraft Type
2-3-7 USAF/USN Undergraduate Pilots
2-3-8 Aircraft Equipment Suffix
2-3-10 Control Symbology
Local Qualification Standards
KNOWLEDGE. Pass a written examination encompassing the requirement with a
minimum score of 80.
SKILLS AND ABILITIES
Skill/Ability Date OJTI
Demonstrate the ability to identify civil and
military aircraft using call sign prefixes.
Demonstrate the skill to properly complete flight
progress strips.
Demonstrate the ability to properly forward
aircraft equipment suffixes.
Demonstrate the ability to use the proper code for
test flight plans.
Demonstrate the skill to post flight progress
strips and data to the appropriate position.
Demonstrate the ability to write a manual copy with
return strip and enter them correctly into the
STARS display.
Demonstrate the ability to identify what
information goes in each block of a flight progress
strip for both arrivals and departures.
Demonstrate the ability to record a pointout from
an adjacent facility.
Individual has satisfactorily completed all LQS requirements for LTG 3:
Date: _____________
Trainee: ___________________________ Signature: ________________________
FWO/Crew Chief Signature _______________________________
LTG 4 – ATC CLEARANCE/PHRASEOLOGY (ACAD-0523)
Lesson Topic Guide
GOAL. Describe ATC clearance knowledge and phraseology.
REQUIREMENT
1. Identify the clearance items.
2. Describe how to relay clearances.
3. Describe the phraseology to issue route and altitudes amendments.
4. Describe the phraseology to issue a through clearance.
5. Describe the phraseology to issue an altitude reservation (ALTRV)
clearance.
INSTRUCTOR. BI.
REFERENCE
1. FAA JO 7110.65
4-2-1 Clearance Items
4-2-4 Clearance Relay
4-2-5 Route and Altitude Amendments
4-2-6 Through Clearances
4-2-7 ALTRV Clearances
4-2-8 IFR-VFR and VFR-IFR Flights
4-5-2 Flight Direction
4-5-4 Lowest Usable Flight Level
Local Qualification Standards
KNOWLEDGE. Pass a written examination encompassing the requirement with a
minimum score of 80.
SKILLS AND ABILITIES. NA
Skill/Ability Date OJTI
Individual has satisfactorily completed all LQS requirements for LTG 4:
Date: _____________
Trainee: ___________________________ Signature: ________________________
FWO/Crew Chief Signature _______________________________
LTG 13 – RADAR EQUIPMENT PRINCIPLES (ACAD-0532)
Lesson Topic Guide
GOAL. Identify radar equipment usage.
REQUIREMENT. Identify radar equipment principles, to include the following:
1. Presentation and equipment performance.
2. Alignment accuracy check.
3. Radar use.
4. Beacon range accuracy.
5. Electronic cursor.
6. Altitude filters.
7. Standby/low sensitivity operation.
8. Inoperative interrogator.
9. In-flight deviations from transponder.
10. Automated Radar Terminal Systems (ARTS)–Terminal.
11. TPX-42–Terminal.
12. Facility equipment general.
13. Radar use.
14. Video maps.
15. Airport facilities.
16. Radar operations equipment.
17. Precision approach landing system approach criteria.
18. Facility equipment.
INSTRUCTOR. BI.
REFERENCE
1. FAA JO 7110.65
5-1-1 Presentation and Equipment Performance
5-1-2 Alignment Accuracy Check
5-1-3 ATC Surveillance Source Use
5-1-4 Beacon Range Accuracy
5-1-7 Electronic Cursor
5-2-13 Standby or Low Sensitivity Operation
5-2-16 Inoperative or Malfunctioning Interrogator
5-2-21 Automatic Altitude Reporting
5-2-22 Inflight Deviations From Transponder Requirements
5-2-23 Beacon Termination
5-2-24 Altitude Filters
5-15-1 Application
5-15-2 Responsibility
5-15-3 Functional Use
5-15-4 System Requirements
5-15-5 Information Displayed
5-15-6 CA/MCI
5-15-7 Inhibiting Minimum Safe Altitude Warning (MSAW)
5-15-8 Track Suspend Function
2. FAA JO 7210.3
Ch3 Sec1 (Facility Equipment) General
Ch3 Sec7 Radar Use
Ch3 Sec8 Video Maps
3. NAVAIR 00-80T-114
3.5 Airport Facilities
10.2.1 Equipment Requirements
App S Precision Approach Landing System Approach Criteria
Local Qualification Standards
KNOWLEDGE. Pass a written examination encompassing the requirement with a
minimum score of 80%.
SKILLS AND ABILITIES. Will be evaluated during LTG 23 and LTG 24.
Individual has satisfactorily completed all LQS requirements for LTG 13:
Date: _____________
Trainee: ___________________________ Signature: ________________________
FWO/Crew Chief Signature _______________________________
LTG 14 – RADAR FINAL CONTROL KNOWLEDGE (ACAD-0533)
Lesson Topic Guide
GOAL. Comprehend radar final control knowledge.
REQUIREMENT. Describe the procedures listed in the reference.
INSTRUCTOR. BI.
REFERENCE
1. FAA JO 7110.65
2-1-25 Wheels Down Check
3-1-13 Establishing Two-Way Communications
5-6-1 Application (Vectoring)
5-6-2 Methods (Vectoring)
5-7-1 Application (Speed Adjustment)
5-7-2 Methods
5-7-3 Speed Assignments
5-7-4 Termination
5-9-5 Approach Separation Responsibility
5-10-3 No-Gyro Approach
5-10-4 Lost Communications
5-10-5 Radar Contact Lost
5-10-6 Landing Check
5-10-7 Position Information
5-10-8 Final Controller Changeover
5-10-9 Communications Check
5-10-10 Transmission Acknowledgment
5-10-11 Missed Approach
5-10-12 Low Approach and Touch-and-Go
5-10-13 Tower Clearance
5-10-14 Final Approach Abnormalities
5-10-15 Military Single Frequency Approaches
5-11-1 Altitude Information
5-11-2 Visual Reference Point
5-11-3 Descent Notification
5-11-4 Descent Instructions
5-11-5 Final Approach Guidance
5-11-6 Approach Guidance Termination (ASR)
5-12-1 Glidepath Notification
5-12-2 Decision Height (DH) Notification
5-12-3 Descent Instruction
5-12-4 Glidepath and Course Information
5-12-5 Distance From Touchdown
5-12-6 Decision Height
5-12-7 Position Advisories
5-12-8 Approach Guidance Termination (PAR)
5-12-9 Communication Transfer
5-12-10 Elevation Failure
5-12-11 Surveillance Unusable
5-13-1 Monitor On PAR Equipment
5-13-2 Monitor Availability
5-13-3 Monitor Information
2. NAVAIR 00-80T-114
3.3.3.2.1 RFC Trainees
9.2.6.7.4 PAR Target Interpretation
9.2.6.7.5 Safety Limits Exceeded
Local Qualification Standards
KNOWLEDGE. Satisfactorily complete test LTG 14.
SKILLS AND ABILITIES
Skill/Ability Date OJTI
Demonstrate the skill of reminding aircraft to
check wheels down on each approach at the proper
time.
Demonstrate the ability ensure that established
separation is maintained.
Demonstrate the skill to conduct a no gyro
approach.
Demonstrate the ability to determine when lost
communication instructions must be issued and is
done correctly.
Demonstrate the ability to properly respond to an
aircraft that you have lost radar contact with.
Demonstrate the skill of asking for a
communications check on each approach.
Demonstrate the skill of instructing the aircraft
not to acknowledge further transmissions.
Demonstrate the ability to issue missed approach
procedures when appropriate.
Demonstrate the skill to issue proper climbout
instructions for different types of approaches.
Demonstrate the ability to issue a clearance to
land, touch and go or low approach obtained from
the tower.
Demonstrate the ability to properly respond to a
clearance canceled or not received from the tower.
Demonstrate the skill to respond to final approach
abnormalities.
Demonstrate the ability to provide recommended
altitudes for surveillance approaches.
Demonstrate the ability to request aircraft to
report the airport/runway in sight for surveillance
approaches.
Demonstrate the ability to notify aircraft where
descent will begin and MDA for surveillance
approaches.
Demonstrate the skill to issue course guidance
every 15 seconds for surveillance approaches and 5
seconds for precision approaches.
Demonstrate the ability to inform aircraft when it
is approaching glidepath and when to begin descent.
Demonstrate the skill of informing aircraft when it
reaches decision height, passes over approach
lights and passes over landing threshold.
Demonstrate the ability to properly terminate a
surveillance approach or precision approach.
Demonstrate the ability to properly monitor an ILS
approach using PAR.
Demonstrate the ability to issue a speed
adjustment.
Demonstrate the ability to maintain established
separation between aircraft under your control and
other aircraft on final.
Demonstrate the skill to conduct a no-gyro PAR and
ASR approach.
Demonstrate the skill to issue lost communications
instructions when required.
Demonstrate the ability to instruct aircraft not to
acknowledge further transmissions.
Demonstrate the ability to issue a missed approach
procedure when required.
Demonstrate the ability to issue appropriate
departure instructions for low approach or touch
and go aircraft.
Demonstrate the ability to obtain a clearance from
the tower or respond to a clearance cancelled/not
received.
Demonstrate the skill to interpret final approach
abnormalities.
Individual has satisfactorily completed all LQS requirements for LTG 14:
Date: _____________
Trainee: ___________________________ Signature: ________________________
FWO/Crew Chief Signature _______________________________
LTG 15 – BASIC RADAR (ACAD-0534)
Lesson Topic Guide
GOAL. Comprehend basic radar knowledge.
REQUIREMENT. Describe the following IAW the reference:
1. Formation flights.
2. Wake turbulence.
3. Wake turbulence cautionary advisories.
4. Observed abnormalities.
5. Landing area condition.
6. Timely information.
7. Traffic advisories.
8. Bird activity information.
9. Traffic information.
10. Altitude restricted approach.
11. Vertical separation minima.
12. Single frequency approaches (SFA).
13. Clearance relay.
14. Transfer of radar identification.
15. Circling approach.
16. Radar identification.
17. Radar separation.
18. Radar arrivals.
INSTRUCTOR. BI
REFERENCE
1. FAA JO 7110.65
2-1-13 Formation Flights
2-1-15 Control Transfer
2-1-19 Wake Turbulence
2-1-20 Wake Turbulence Cautionary Advisories
2-1-21 Traffic Advisories
2-1-22 Unmanned Aircraft System (UAS) Activity Information
2-1-23 Bird Activity Information
2-2-5 IFR to VFR Flight Plan Change
3-1-6 Traffic Information
3-1-10 Observed Abnormalities
3-3-1 Landing Area Conditions
3-3-3 Timely Information
3-10-10 Altitude Restricted Approach
4-5-1 Vertical Separation Minima
4-7-3 Single Frequency Approaches (SFA)
4-7-8 Below Minima Report By Pilot
4-8-3 Relayed Approach Clearance
4-8-6 Circling Approach
4-8-8 Communications Release
5-3-1 Application
5-3-2 Primary Radar Identification Methods
5-3-3 Beacon Identification Methods
5-3-5 Questionable Identification
5-4-1 Application
5-4-3 Methods (Transfer of Radar ID)
5-4-4 Traffic (Radar Separation)
5-4-5 Transferring Controller Handoff
5-5-1 Application (Radar Separation)
5-5-2 Target Separation
5-5-4 Minima (Radar Separation)
5-5-8 Additional Separation For Formation Flights
5-9-1 Vectors to Final Approach Course
5-9-2 Final Approach Course Interception
5-9-3 Vectors Across Final Approach Coarse
5-9-4 Arrival Instructions
5-9-5 Approach Separation Responsibility
10-2-8 Radar Assistance to VFR Aircraft in Weather Difficulty
Local Qualification Standards
KNOWLEDGE. Pass a written examination with a minimum score of 80.
SKILLS AND ABILITIES
Skill/Ability Date OJTI
Demonstrate the ability to maintain proper wake turbulence
separation behind heavy jets.
Demonstrate the ability to issue traffic advisories.
Demonstrate the ability to pass bird activity, traffic,
observed abnormalities or landing area conditions received
from the tower verbatim.
Demonstrate the ability to clear aircraft for restricted
low approaches.
Demonstrate the ability to clear an aircraft for a
circling approach.
Demonstrate the ability to radar identify an aircraft be
primary or secondary means.
Demonstrate the ability to properly transfer radar
identification.
Demonstrate the ability to apply radar separation.
Demonstrate the ability to vector aircraft without a gyro.
Individual has satisfactorily completed all LQS requirements for LTG 15:
Date: _____________
Trainee: ___________________________ Signature: ________________________
FWO/Crew Chief Signature _______________________________
LTG 19 – RADAR COORDINATION (ACAD-0538)
Lesson Topic Guide
GOAL. Describe radar coordination procedures.
REQUIREMENT. Describe the following IAW the reference:
1. Radio and interphone communication monitoring.
2. Authorized interruptions.
3. Authorized relays.
4. Clearance prefix.
5. Departure clearances.
6. Abbreviated departure clearance.
7. Delay sequencing.
8. Delays.
9. Forward departure delay info.
10. Coordination with receiving facility.
11. Forwarding departure times.
INSTRUCTOR. BI.
REFERENCE
1. FAA JO 7110.65
2-1-14 Coordinate Use of Airspace
4-2-2 Clearance Prefix
4-3-2 Departure Clearances
4-3-3 Abbreviated Departure Clearance
4-3-6 Delay Sequencing
4-3-7 Forward Departure Delay Information
4-3-8 Coordination With Receiving Facility
4-3-10 Forwarding Departure Times
4-6-3 Delays
Local Qualification Standards
KNOWLEDGE. Pass a written examination with a minimum score of 80.
SKILLS AND ABILITIES
Skill/Ability Date OJTI
Individual has satisfactorily completed all LQS requirements for LTG 19:
Date: _____________
Trainee: ___________________________ Signature: ________________________
FWO/Crew Chief Signature _______________________________
LTG 23 – RADAR EQUIPMENT (EQPT-2018)
Lesson Topic Guide
GOAL. Operate radar equipment.
REQUIREMENT. Given the required equipment, conduct the following:
1. Configure the ASR scope for daily operations.
2. Configure PAR for daily operations.
3. Ensure transmitter/receiver control panel(s) are functional.
4. Use intercom units to conduct a communications check.
5. Read altimeter, wind instruments, and clock information.
6. Ensure NAVAID monitors are operating properly, read indicators, and
identify equipment status.
7. Navigate through different screens in the VIDS.
8. Operate the weather reporting monitor to extract information.
9. Operate the VISCOM
10. Perform alignment checks.
11. Operate the Emergency Communications System (ECS).
INSTRUCTOR. BI
PREREQUISITE. ACAD-0532
Local Qualification Standards
KNOWLEDGE. Satisfactorily complete test LTG 13.
SKILLS AND ABILITIES. Demonstrate the proper operation of the following with
no assistance from the instructor.
Skill/Ability Date OJTI
Demonstrate the ability to read altimeter, wind
instruments and clock information.
Demonstrate the ability to configure the ASR scope
for an approach.
Demonstrate the ability to configure the PAR scope
to the correct runway.
Demonstrate the skill to perform an alignment check
on the PAR scope.
Demonstrate the ability to relay weather
information.
Demonstrate the skill of navigating through
different menus and screens on the VIDS.
Demonstrate the ability to operate the VISCOM
correctly.
Individual has satisfactorily completed all LQS requirements for LTG 23:
Date: _____________
Trainee: ___________________________ Signature: ________________________
FWO/Crew Chief Signature _______________________________
LTG 25 – RADAR COMMUNICATIONS EQUIPMENT (COMM-2206)
Lesson Topic Guide
GOAL. Operate ATC communications equipment.
REQUIREMENT. While in a RATCF, operate the following communications
equipment:
1. Transmitter/receiver control panel(s).
2. Backup/emergency transmitter/receiver location and controls.
3. Emergency communications system (ECS).
4. Crash Phone
5. Intercom units.
6. Telephones.
7. VIDS.
INSTRUCTOR. BI.
PREREQUISITE. None.
Local Qualification Standards
KNOWLEDGE. Must have completed test LTG 13.
SKILLS AND ABILITIES
Skill/Ability Date OJTI
Demonstrate the ability to operate the ETVS.
Demonstrate the ability to operate the intercom
between positions.
Individual has satisfactorily completed all LQS requirements for LTG 25:
Date: _____________
Trainee: ___________________________ Signature: ________________________
FWO/Crew Chief Signature _______________________________
LTG FC26 – LOCAL PROCEDURES
Lesson Topic Guide
GOAL. Describe information contained in local directives.
REQUIREMENT. Given the reference material, identify the key information
contained.
INSTRUCTOR. BI.
REFERENCE
1. Letters of Agreement.
2. Facility Manual
2-606 Intrafacility Landlines
2-608 Local Frequencies
6-100 General
6-101 Airspace
6-200 Terminal Radar Team Positions
6-209 Final Control
6-302 Contact Approach
6-303 GCA and ILS Patterns
6-306 Radar Approach Minimums
6-307 ASR Recommended Altitudes
6-308 Climbout Instructions
6-309 Special Use Airspace Schedule
6-311 VISCOM Coordination
6-316 Cherry Point Waveoffs
6-317 AV-8 Minimum Fuel GCA
6-319 Missed Approach Instructions
6-320 Lost Comm Instructions
6-321 Restricted Low Approach
6-322 Radar Approach Confirmation
6-323 Runway Threshold and Approach Light Calls for PAR
6-324 Information and Status Boards
6-329 Pointouts
7-102 ETVS
7-105 Emergency Comm System
7-112 Visual Communications (VISCOM)
7-205 FPN-63 Precision Radar
7-206 FPN-63 Control Panel
7-207 FPN-63 Remote Control Panel
7-302 NAVAID Monitors
7-303 Navigation Aids
3. NAVAIR 00-80T-114
10.1.3.7 Final Control
Local Qualification Standards
KNOWLEDGE. Satisfactorily complete test LTG 26.
SKILLS AND ABILITIES
Skill/Ability Date OJTI
Individual has satisfactorily completed all LQS requirements for LTG 26:
Date: _____________
Trainee: ___________________________ Signature: ________________________
FWO/Crew Chief Signature _______________________________
LTG 27 – BASIC INSTRUCTOR (IUT-5000/5010/5020)
Lesson Topic Guide
GOAL.
1. Introduce principles of instruction.
2. Understand the structure of an event.
3. Conduct a period of instruction on a T&R event.
REQUIREMENT.
1. Given the reference, the BIUT will demonstrate the following with the
assistance of a unit instructor:
a. Introduce/discuss/demonstrate instruction techniques.
b. Introduce/discuss/demonstrate class management techniques.
(1) How to use class resources to communicate with the student.
(2) How to properly organize the class for effective instruction.
c. Introduce/discuss/demonstrate how to prepare for a period of
instruction.
(1) Schedule the class.
(2) Prepare/access the training materials for the class.
(3) Prepare the evaluation form to be used to evaluate the students
event performance, as applicable.
2. Using the community T&R manual, discuss the following with an instructor:
a. State the purpose of a T&R event.
b. Describe the structure of a T&R event and explain the purpose and
content for each event section.
c. Using the given event, explain each section as it pertains to the
event.
(1) Explain the purpose and content of the goal.
(2) Explain the requirement condition and performance steps for the
event and what needs to be done to prepare to instruct the event.
(3) Explain how the event performance standard is measured and when
the event has been completed.
(4) State who can instruct the event.
(5) State the event prerequisite and how to verify that it was
completed.
(6) Explain how the external syllabus support requirement will be
resourced.
(7) State the references required and how each would be used to train
the event.
3. The BIUT, under the supervision of an instructor, will learn how to
conduct a period of instruction on an event selected by the instructor. The
event must be one the BIUT is current and proficient in. The BIUT will be
able to:
a. State the instructor responsibilities.
b. Define the purpose and content of a T&R event per the aviation T&R
program manual.
c. Prepare to train the event.
(1) Review the trainee’s PR to identify required training for the
event selected.
(2) Ensure the student has met prerequisites for the event to be
trained.
(3) Develop a student training plan to ensure progression per this
manual.
(4) Schedule the training event (facilities and students).
(5) Gather the resources necessary to conduct the training
(instructional materials, references and equipment).
(6) Prepare an evaluation form for each student to be evaluated.
d. Conduct training on the event selected:
(1) Ensure all training resources are properly staged/equipment if
set up properly for training.
(2) Instruct the student in a thorough manner so as to cover all
requirements for the event.
(3) Ensure continuous, objective assessment of the students’ progress
during training.
e. Assess student performance:
(1) Assess the students’ performance to the performance standard.
(2) Correct student deficiencies in a timely manner and provide the
student feedback.
(3) Complete the evaluation form for each student trained.
(4) Debrief students on their performance and provide corrective
action.
f. Route evaluation form, as required.
INSTRUCTOR. BI.
REFERENCE. NAVMC 3500.14
Local Qualification Standards
KNOWLEDGE. There is no test for LTG 27.
SKILLS AND ABILITIES
Skill/Ability Date SI
Demonstrate an understanding of the principles of
instruction verbally.
Physically demonstrate proper instruction and
classroom techniques.
Demonstrate event required knowledge.
Demonstrate how to schedule and prepare to instruct
an event.
Without the aid of references and during a
discussion session, demonstrate an understanding of
the structure of T&R events.
Conduct a period of instruction on a T&R event.
Individual has satisfactorily completed all LQS requirements for LTG 27:
Date: _____________
Trainee: ___________________________ Signature: ________________________
FWO/Crew Chief Signature _______________________________
Section V TOWER FLIGHT DATA
LTG 1 - RADIO AND INTERPHONE COMMUNICATIONS (ACAD-0520)
Lesson Topic Guide
GOAL. Describe radio and interphone communications knowledge.
REQUIREMENT.
1. Describe radios and interphone communications.
INSTRUCTOR. BI.
REFERENCE
1. FAA JO 7110.65
2-4-1 Radio Communications
2-4-2 Monitoring
2-4-14 Words and Phrases
2-4-15 Emphasis for Clarity
2-4-16 ICAO Phonetics
2-4-17 Numbers Usage
2-4-18 Number Clarification
2-4-19 Facility Identification
2-4-20 Aircraft Identification
2-4-21 Description of Aircraft Types
2-4-22 Airspace Classes
Local Qualification Standards
KNOWLEDGE. Pass a written examination encompassing the requirement with a
minimum score of 80%.
SKILLS AND ABILITIES
Skill/Ability Date OJTI
Demonstrate the ability to monitor interphones and
assigned radio frequencies continuously.
Demonstrate the skill of using the word “heavy” as
part of the identification of heavy aircraft.
Demonstrate the ability to use ICAO pronunciation
of numbers and letters.
Demonstrate the skill to state numbers properly for
altitudes, flight levels, time, altimeter, speed,
wind, headings, beacon codes, runways and
frequencies.
Demonstrate the skill to use proper aircraft
identification.
Individual has satisfactorily completed all LQS requirements for LTG 1:
Date: _____________
Trainee: ___________________________ Signature: ________________________
FWO/Crew Chief Signature _______________________________
LTG 2 - AIRCRAFT MOVEMENT DATA (ACAD-0521)
Lesson Topic Guide
GOAL. Describe aircraft movement data knowledge.
REQUIREMENT.
1. Describe the terms of acknowledgement of clearances and instructions.
2. Describe interphone transmission priorities.
3. Describe the terms for priority interruption.
4. Describe the interphone format.
INSTRUCTOR. BI.
REFERENCE
1. FAA JO 7110.65
2-4-3 Pilot Acknowledgement/Read Back
2-4-4 Authorized Interruptions
2-4-5 Authorized Transmissions
2-4-6 False or Deceptive Communications
2-4-7 Authorized Relays
2-4-8 Radio Message Format
2-4-9 Abbreviated Transmissions
2-4-10 Interphone Transmission Priorities
2-4-11 Priority Interruption
2-4-12 Interphone Message Format
2-4-13 Interphone Message Termination
Local Qualification Standards
KNOWLEDGE. Pass a written examination encompassing the requirement with a
minimum score of 80%.
SKILLS AND ABILITIES
Skill/Ability Date OJTI
Demonstrate the ability to communicate using proper
radio message format.
Demonstrate the skill of abbreviating transmissions
after communications have been established.
Demonstrate the ability to terminate interphone
messages with your operating initials.
Demonstrate the ability to use the proper format
for interphone messages.
Demonstrate the skill to properly prioritize
interphone messages.
Demonstrate the ability to interrupt lower priority
messages.
Individual has satisfactorily completed all LQS requirements for LTG 2:
Date: _____________
Trainee: ___________________________ Signature: ________________________
FWO/Crew Chief Signature _______________________________
LTG 3 – FLIGHT PROGRESS STRIPS (ACAD-0522)
Lesson Topic Guide
GOAL. Describe flight progress strip knowledge.
REQUIREMENT
1. Describe the methods for updating information on flight progress strips.
2. Label flight progress strips, to include:
a. Arrivals.
b. Departures.
c. Overflights.
d. Enroute aircraft.
3. List aircraft prefixes.
4. List aircraft suffixes.
5. List flight progress strip control information symbols.
INSTRUCTOR. BI.
REFERENCE
1. FAA JO 7110.65
2-3-1 General
2-3-4 Terminal Data Entries
2-3-5 Aircraft Identity
2-3-6 Aircraft Type
2-3-7 USAF/USN Undergraduate Pilots
2-3-8 Aircraft Equipment Suffix
2-3-10 Control Symbology
Local Qualification Standards
KNOWLEDGE. Pass a written examination encompassing the requirement with a
minimum score of 80%.
SKILLS AND ABILITIES
Skill/Ability Date OJTI
Demonstrate the ability to identify civil and
military aircraft using call sign prefixes.
Demonstrate the skill to properly complete flight
progress strips.
Demonstrate the ability to properly forward
aircraft equipment suffixes.
Demonstrate the ability to use the proper code for
test flight plans.
Demonstrate the skill to post flight progress
strips and data to the appropriate position.
Demonstrate the ability to write a manual copy with
return strip and enter them correctly into the
STARS display.
Demonstrate the ability to identify what
information goes in each block of a flight progress
strip for both arrivals and departures.
Demonstrate the ability to record a pointout from
an adjacent facility.
Individual has satisfactorily completed all LQS requirements for LTG 3:
Date: _____________
Trainee: ___________________________ Signature: ________________________
FWO/Crew Chief Signature _______________________________
LTG 4 – ATC CLEARANCE/PHRASEOLOGY (ACAD-0523)
Lesson Topic Guide
GOAL. Describe ATC clearance knowledge and phraseology.
REQUIREMENT
1. Identify the clearance items.
2. Describe how to relay clearances.
3. Describe the phraseology to issue route and altitudes amendments.
4. Describe the phraseology to issue a through clearance.
5. Describe the phraseology to issue an altitude reservation (ALTRV)
clearance.
INSTRUCTOR. BI.
REFERENCE
1. FAA JO 7110.65
4-2-1 Clearance Items
4-2-4 Clearance Relay
4-2-5 Route and Altitude Amendments
4-2-6 Through Clearances
4-2-7 ALTRV Clearances
4-2-8 IFR-VFR and VFR-IFR Flights
4-5-2 Flight Direction
4-5-4 Lowest Usable Flight Level
Local Qualification Standards
KNOWLEDGE. Pass a written examination encompassing the requirement with a
minimum score of 80%.
SKILLS AND ABILITIES.
Skill/Ability Date OJTI
Demonstrate the skill to issue VFR and IFR
clearances.
Demonstrate the ability to amend previously issued
clearances.
Demonstrate the skill to issue an altitude
reservation flight plan clearance.
Individual has satisfactorily completed all LQS requirements for LTG 4:
Date: _____________
Trainee: ___________________________ Signature: ________________________
FWO/Crew Chief Signature _______________________________
LTG 22 – EQUIPMENT (EQPT-2003)
Lesson Topic Guide
GOAL. Operate fixed control tower structure equipment.
REQUIREMENT. While in a fixed tower and given the required equipment,
operate the following:
1. Operate the airfield lighting console/computer.
2. Operate console and cab lighting.
3. Operate cooling and heating controls.
4. Identify and describe operation of emergency power cutoff.
5. Read altimeter, wind instruments and clock information.
6. Ensure NAVAID monitors are operating properly, read indicators, and
identify equipment status.
7. Operate the weather reporting monitor to extract information.
8. Operate ALDIS lamp.
9. Operate PA system.
10. Operate traffic tabulators.
11. Operate BRANDS/BRITE control panel and display.
12. Operate the tower display workstation (TDW)
INSTRUCTOR. BI
PREREQUISITE. None.
Local Qualification Standards
KNOWLEDGE. This event is completed through practical application.
SKILLS AND ABILITIES
Skill/Ability Date OJTI
Demonstrate that you know how to use the Emergency
Power Cutoff equipment. (DO NOT TURN OFF POWER)
Demonstrate the ability to configure airfield
lighting.
Individual has satisfactorily completed all LQS requirements for LTG 22:
Date: _____________
Trainee: ___________________________ Signature: ________________________
FWO/Crew Chief Signature _______________________________
LTG 24 – EQUIPMENT (EQPT-2019)
Lesson Topic Guide
GOAL. Operate flight data equipment.
REQUIREMENT. While in a control tower and given the required equipment,
configure or operate the following:
1. Traffic tabulators.
2. Operate FDIO to include:
Input flight plans
Amend flight plans
Weather report
General information message
Hold message
Departure message
Progress report
ARTS force flight progress data
Restore database
Stereo flight plan
Input station altimeter
Remove flight plan
3. Tower Display Workstation.
4. Personal computer.
5. Wind Indicators.
6. Altimeter Readout.
7. Clocks.
8. ATIS.
INSTRUCTOR. BI
PREREQUISITE. None.
Local Qualification Standards
KNOWLEDGE. This event is completed through practical application.
SKILLS AND ABILITIES
Skill/Ability Date OJTI
Demonstrate the ability to record operations on the
ATAA.
Demonstrate the ability to access the electronic
ATC library.
Demonstrate the skill to use the ATIS.
Demonstrate the ability to properly record an ATIS
broadcast.
Demonstrate the ability to input the following using the FDIO equipment.
Flight Plan – FP
Amendment Message – AM
Departure Message – DM
Flight Plan Readout – FR
General Information – GI
Hold Message – HM
Progress Report – PR
Restore Database – RB
ARTS Force – RF
Remove Strip – RS
Stereo Flight Plan – SP
Strip Request – SR
Test Device – TD
Weather Request- WR
Demonstrate the skill to load blank strips into the
FDIO printer.
Individual has satisfactorily completed all LQS requirements for TFD 7:
Date: _____________
Trainee: ___________________________ Signature: ________________________
FWO/Crew Chief Signature _______________________________
LTG 25 – COMMUNICATIONS EQUIPMENT (COMM-2206)
Lesson Topic Guide
GOAL. Operate control tower communications equipment.
REQUIREMENT. While in a control tower, operate the following communications
equipment:
1. Transmitter/receiver control panel.
2. Backup/emergency transmitter/receiver location and controls.
3. Emergency alert system.
4. Intercom units.
5. P.A. system.
6. Telephones.
7. Aldis lamp.
8. VIDS
INSTRUCTOR. BI.
PREREQUISITE. None.
Local Qualification Standards
KNOWLEDGE. This event is completed through practical application.
SKILLS AND ABILITIES
Skill/Ability Date OJTI
Demonstrate ability to operate the
transmitter/receiver control panel.
Demonstrate the ability to locate the wind and
altimeter.
Demonstrate the proper use of local time and zulu
time.
Conduct a proper position relief.
Demonstrate the proper use of position logs
(VIDS/paper) to sign on and off.
Demonstrate the ability to update status boards.
Individual has satisfactorily completed all LQS requirements for TFD 8:
Date: _____________
Trainee: ___________________________ Signature: ________________________
FWO/Crew Chief Signature _______________________________
LTG FD26 - LOCAL PROCEDURES
Lesson Topic Guide
GOAL. Comprehend general ATC knowledge.
REQUIREMENT. Describe the information listed in the reference.
INSTRUCTOR. BI.
REFERENCE
1. FAA JO 7110.65
2-1-5 Expeditious Compliance
2-1-9 Reporting Essential Flight Information
2-1-10 NAVAID Malfunctions
2-1-11 Use of MARSA
2-1-12 Military Procedures
2-1-17 Radio Communications
2-1-18 Operational Requests
2-1-23 Transfer of Position Responsibility
2-1-25 Supervisory Notification
2. Glossary
Acknowledge
Roger
Say Again
Stand By
Unable
3. Facility Manual
2-600 Local Based Squadrons
2-605 Interfacility Landlines
2-606 Intrafacility Landlines
2-608 Local Frequencies
2-800 Civil Use Landing Permit
2-801 Emergency Landings
2-802 Aircraft Without PPR
5-205 Tower Flight Data
5-404 Standard IFR Departure Climbout
5-405 Local IFR Clearances
5-407 VFR on Top
5-409 Arresting Gear Status
5-416 FDIO Test Flight Plans
5-419 Data Entries for NJM
5-420 Airport Status Board
5-427 Crash Circuit Test
5-429 Stereo Routes and VFR Flight Guarding
5-500 General
5-501 Terminal Data Entries
5-502 Control Symbology
5-503 Departure Strips
5-702 Emergency Notification
5-703 Hot Brakes
7-100 General
7-101 ATIS
7-103 Crash/Emergency Alert System
7-108 FDIO
7-401 Clocks
7-402 Altimeter Setting
7-404 Wind Indicators
App H Flight Data Input/Output (FDIO) Handbook
4. Airfield Operations Manual
2.1. General
2.2. Flight Planning
2.3. Instructions for Filing and Completing Flight Plans
2.6. Stereo Route/Pre-filed Flight Plan
2.11. Overdue Aircraft Procedures
5. NAVAIR 00-80T-114
9.1.3.3 Flight Data
6. Letters of Agreement
Z10 - Stereotype Flight Plans for MAG 14, Cherry Point, NC and MAG 31,
Beaufort, SC
Z11 - Stereotyped Flight Plans for Marine Aircraft Group - 14
Local Qualification Standards
KNOWLEDGE. Pass a written examination encompassing the requirement with a
minimum score of 80%.
SKILLS AND ABILITIES
Skill/Ability Date OJTI
Individual has satisfactorily completed all LQS requirements for LTG 26:
Date: _____________
Trainee: ___________________________ Signature: ________________________
FWO/Crew Chief Signature _______________________________
Section VI GROUND CONTROL
LTG 1 - RADIO AND INTERPHONE COMMUNICATIONS (ACAD-0520)
Lesson Topic Guide
GOAL. Describe radio and interphone communications knowledge.
REQUIREMENT.
1. Describe radios and interphone communications.
INSTRUCTOR. BI.
REFERENCE
1. FAA JO 7110.65
2-4-1 Radio Communications
2-4-2 Monitoring
2-4-14 Words and Phrases
2-4-15 Emphasis for Clarity
2-4-16 ICAO Phonetics
2-4-17 Numbers Usage
2-4-18 Number Clarification
2-4-19 Facility Identification
2-4-20 Aircraft Identification
2-4-21 Description of Aircraft Types
2-4-22 Airspace Classes
Local Qualification Standards
KNOWLEDGE. Pass a written examination encompassing the requirement with a
minimum score of 80%.
SKILLS AND ABILITIES
Skill/Ability Date OJTI
Demonstrate the ability to monitor interphones and
assigned radio frequencies continuously.
Demonstrate the skill of using the word “heavy” as
part of the identification of heavy aircraft.
Demonstrate the ability to use ICAO pronunciation
of numbers and letters.
Demonstrate the skill to state numbers properly for
altitudes, flight levels, time, altimeter, speed,
wind, headings, beacon codes, runways and
frequencies.
Demonstrate the skill to use proper aircraft
identification.
Individual has satisfactorily completed all LQS requirements for LTG 1:
Date: _____________
Trainee: ___________________________ Signature: ________________________
FWO/Crew Chief Signature _______________________________
LTG 2 - AIRCRAFT MOVEMENT DATA (ACAD-0521)
Lesson Topic Guide
GOAL. Describe aircraft movement data knowledge.
REQUIREMENT.
1. Describe the terms of acknowledgement of clearances and instructions.
2. Describe interphone transmission priorities.
3. Describe the terms for priority interruption.
4. Describe the interphone format.
INSTRUCTOR. BI.
REFERENCE
1. FAA JO 7110.65
2-4-3 Pilot Acknowledgement/Read Back
2-4-4 Authorized Interruptions
2-4-5 Authorized Transmissions
2-4-6 False or Deceptive Communications
2-4-7 Authorized Relays
2-4-8 Radio Message Format
2-4-9 Abbreviated Transmissions
2-4-10 Interphone Transmission Priorities
2-4-11 Priority Interruption
2-4-12 Interphone Message Format
2-4-13 Interphone Message Termination
Local Qualification Standards
KNOWLEDGE. Pass a written examination encompassing the requirement with a
minimum score of 80%.
SKILLS AND ABILITIES
Skill/Ability Date OJTI
Demonstrate the ability to communicate using proper
radio message format.
Demonstrate the skill of abbreviating transmissions
after communications have been established.
Demonstrate the ability to terminate interphone
messages with your operating initials.
Demonstrate the ability to use the proper format
for interphone messages.
Demonstrate the skill to properly prioritize
interphone messages.
Demonstrate the ability to interrupt lower priority
messages.
Individual has satisfactorily completed all LQS requirements for LTG 2:
Date: _____________
Trainee: ___________________________ Signature: ________________________
FWO/Crew Chief Signature _______________________________
LTG 3 – FLIGHT PROGRESS STRIPS (ACAD-0522)
Lesson Topic Guide
GOAL. Describe flight progress strip knowledge.
REQUIREMENT
1. Describe the methods for updating information on flight progress strips.
2. Label flight progress strips, to include:
a. Arrivals.
b. Departures.
c. Overflights.
d. Enroute aircraft.
3. List aircraft prefixes.
4. List aircraft suffixes.
5. List flight progress strip control information symbols.
INSTRUCTOR. BI.
REFERENCE
1. FAA JO 7110.65
2-3-1 General
2-3-4 Terminal Data Entries
2-3-5 Aircraft Identity
2-3-6 Aircraft Type
2-3-7 USAF/USN Undergraduate Pilots
2-3-8 Aircraft Equipment Suffix
2-3-10 Control Symbology
Local Qualification Standards
KNOWLEDGE. Pass a written examination encompassing the requirement with a
minimum score of 80%.
SKILLS AND ABILITIES
Skill/Ability Date OJTI
Demonstrate the ability to identify civil and
military aircraft using call sign prefixes.
Demonstrate the skill to properly complete flight
progress strips.
Demonstrate the ability to properly forward
aircraft equipment suffixes.
Demonstrate the ability to use the proper code for
test flight plans.
Demonstrate the skill to post flight progress
strips and data to the appropriate position.
Demonstrate the ability to write a manual copy with
return strip and enter them correctly into the
STARS display.
Demonstrate the ability to identify what
information goes in each block of a flight progress
strip for both arrivals and departures.
Demonstrate the ability to record a pointout from
an adjacent facility.
Individual has satisfactorily completed all LQS requirements for LTG 3:
Date: _____________
Trainee: ___________________________ Signature: ________________________
FWO/Crew Chief Signature _______________________________
LTG 4 – ATC CLEARANCE/PHRASEOLOGY (ACAD-0523)
Lesson Topic Guide
GOAL. Describe ATC clearance knowledge and phraseology.
REQUIREMENT
1. Identify the clearance items.
2. Describe how to relay clearances.
3. Describe the phraseology to issue route and altitudes amendments.
4. Describe the phraseology to issue a through clearance.
5. Describe the phraseology to issue an altitude reservation (ALTRV)
clearance.
INSTRUCTOR. BI.
REFERENCE
1. FAA JO 7110.65
4-2-1 Clearance Items
4-2-4 Clearance Relay
4-2-5 Route and Altitude Amendments
4-2-6 Through Clearances
4-2-7 ALTRV Clearances
4-2-8 IFR-VFR and VFR-IFR Flights
4-5-2 Flight Direction
4-5-4 Lowest Usable Flight Level
Local Qualification Standards
KNOWLEDGE. Pass a written examination encompassing the requirement with a
minimum score of 80%.
SKILLS AND ABILITIES.
Skill/Ability Date OJTI
Demonstrate the skill to issue VFR and IFR
clearances.
Demonstrate the ability to amend previously issued
clearances.
Demonstrate the skill to issue an altitude
reservation flight plan clearance.
Individual has satisfactorily completed all LQS requirements for LTG 4:
Date: _____________
Trainee: ___________________________ Signature: ________________________
FWO/Crew Chief Signature _______________________________
LTG 5 – AIRFIELD LIGHTING (ACAD-0524)
Lesson Topic Guide
GOAL. Comprehend airfield lighting knowledge.
REQUIREMENT. Describe the use of airfield lighting listed in the reference
and be able to determine intensity levels through the use of tables.
INSTRUCTOR. BI
REFERENCE
1. FAA JO 7110.65
3-4-1 Emergency Lighting
3-4-2 Runway End Identifier Lights
3-4-3 VASI Lights
3-4-4 Precision Approach Path Indicators (PAPI)
3-4-5 Approach Lights
3-4-6 ALS Intensity
3-4-7 Sequenced Flashing Lights
3-4-8 MALS
3-4-9 ALSF-2
3-4-10 Runway Edge Lights
3-4-11 High Intensity Runway, Centerline Lights
3-4-12 HIRL Associated with MALSR
3-4-13 HIRL Changes
3-4-14 Medium Intensity Runway Lights
3-4-15 Simultaneous Approach/Runway Edge
3-4-16 High-Speed Turnoff Lights
3-4-17 Taxiway Lights
3-4-18 Obstruction Lights
3-4-19 Rotating Beacon
2. Facility Manual
5-423 Taxiway Lights
3. Airfield Operations Manual
1.9. Airfield Lighting
Local Qualification Standards
KNOWLEDGE. Pass a written examination encompassing the requirement with a
minimum score of 80%.
SKILLS AND ABILITIES
Skill/Ability Date OJTI
Demonstrate the skill to provide appropriate
airport lighting for an emergency.
Demonstrate the ability to operate approach lights
correctly.
Demonstrate the ability to operate sequenced
flashing lights correctly.
Demonstrate the ability to operate runway edge
lights correctly.
Demonstrate the ability to operate taxiway lights
correctly.
Demonstrate the ability to operate the rotating
beacon correctly.
Individual has satisfactorily completed all LQS requirements for LTG 5:
Date: _____________
Trainee: ___________________________ Signature: ________________________
FWO/Crew Chief Signature _______________________________
LTG 6 – SPECIAL VFR (ACAD-0525)
Lesson Topic Guide
GOAL. Comprehend requirements and phraseology for Special VFR operations.
REQUIREMENT. Identify the guidelines and criteria required for Special VFR
operations.
INSTRUCTOR. BI
REFERENCE
1. FAA JO 7110.65
7-5-1 Authorization criteria
7-5-1 Clearance phraseology
7-5-2 SVFR priorities
7-5-3 Separation requirements
7-5-4 Altitude Assignment
7-5-5 Local operations
7-5-6 Climb to VFR
7-5-7 Ground visibility below one mile
7-5-8 Flight visibility below one mile
Local Qualification Standards
KNOWLEDGE. Pass a written examination encompassing the requirement with a
minimum score of 80%.
SKILLS AND ABILITIES
Skill/Ability Date OJTI
Demonstrate the ability to determine when Special
VFR operations are authorized.
Demonstrate the ability to deny Special VFR
clearance when ground visibility is below one mile.
Demonstrate the ability to use proper strip marking
for Special VFR aircraft.
Individual has satisfactorily completed all LQS requirements for LTG 6:
Date: _____________
Trainee: ___________________________ Signature: ________________________
FWO/Crew Chief Signature _______________________________
LTG 8 – ATC PHRASEOLOGY/COMMUNICATIONS (ACAD-0527)
Lesson Topic Guide
GOAL. Comprehend Air Traffic Control Phraseology/Communications as it
applies to ground control.
REQUIREMENT. Understand the proper ATC phraseology/communications procedures
as it applies to ground control.
INSTRUCTOR. BI
REFERENCE
1. FAA JO 7110.65
3-7-1 Ground Traffic Movement
3-7-2 Taxi and Ground Movement Operations
3-7-4 Runway Proximity
3-7-5 Precision Approach Critical Area
2. Local directives.
Local Qualification Standards
KNOWLEDGE. Pass a written examination encompassing the requirement with a
minimum score of 80%.
SKILLS AND ABILITIES
Skill/Ability Date OJTI
Individual has satisfactorily completed all LQS requirements for LTG 8:
Date: _____________
Trainee: ___________________________ Signature: ________________________
FWO/Crew Chief Signature _______________________________
LTG 9 – VEHICLE AND AIRCRAFT MOVEMENT (ACAD-0528)
Lesson Topic Guide
GOAL. Comprehend proper separation to vehicle and aircraft movement as it
applies to ground control.
REQUIREMENT. Define separation criteria for air traffic in the terminal
area. Understand how to provide ATC services based upon observed or known
traffic and airport conditions as listed in the reference.
INSTRUCTOR. BI
REFERENCE
1. FAA JO 7110.65
3-1-1 Provide Service
3-1-2 Preventive Control
3-1-3 Use of Active Runways
3-1-4 Coordination Between Local and Ground
3-1-5 Vehicles/Equipment/Personnel on Runway
3-1-6 Traffic Information
3-1-7 Position Determination
3-1-8 Low Level Wind shear/Microburst Advisories
3-1-10 Observed Abnormalities
3-1-12 Visually Scanning Runways
3-3-1 Landing Area Condition
3-3-2 Closed/Unsafe Runway Information
3-3-3 Timely Information
3-7-3 Ground Operations
3-11-1 Taxi and Ground Movement Operation (Helicopter)
2. Facility Manual
5-103 FOD Walks
5-104 FOD and Helicopters
5-105 FOD Sweepers
5-301 Movement Areas
5-303 Combat Aircraft Loading Area
5-304 Centerline Reflectors
5-417 Taxi Restrictions
5-418 Use of Active Runways
5-422 Operations Along an Active Runway
5-425 Back Taxi for Departure
5-426 Pad Operations
5-703 Hot Brakes
5-704 Crash & Vehicle Net
5-705 Arrested Landings
3. Airfield Operations Manual
1.7. Compass Rose and Compass Swing Sites
1.10. Arresting Gear
3.11 AV-8B Operating Procedures
3.13. Ordnance Arming/De-arming Procedures
3.14. External Ordnance Approach Procedures
3.15. Ordnance Handling and Refueling Operations
4.3. Construction and Maintenance
4.4. Uneven Pavement or Surface Procedures
4.5. Snow, Ice, Slush or Water Procedures
4.6. Removal of Objects
4.7. Airport Lighting System Failure
6.3. Customs and Agriculture Inspections
6.4. Distinguished Visitor Procedures
6.8. Priority for Refueling and Services
6.9. Civil Transient Aircraft
6.10. Concurrent Loading and Fueling of Transient Aircraft
4. NAVAIR 00-80T-114
6.1.3.2 Ground Control
Local Qualification Standards
KNOWLEDGE. Pass a written examination encompassing the requirement with a
minimum score of 80%.
SKILLS AND ABILITIES
Skill/Ability Date OJTI
Demonstrate the ability Taxi aircraft to/from
landing surfaces.
Demonstrate the skill to scan runways and movement
areas.
Demonstrate the ability to verbalize intersection
departure procedures.
Demonstrate the skill to taxi multiple aircraft
without conflict.
Demonstrate the skill to determine position of
vehicles/aircraft before issuing instructions.
Demonstrate the ability to issue progressive taxi
instructions.
Individual has satisfactorily completed all LQS requirements for LTG 9:
Date: _____________
Trainee: ___________________________ Signature: ________________________
FWO/Crew Chief Signature _______________________________
LTG 22 – EQUIPMENT (EQPT-2003)
Lesson Topic Guide
GOAL. Operate fixed control tower structure equipment.
REQUIREMENT. While in a fixed tower and given the required equipment,
operate the following:
1. Operate the airfield lighting console/computer.
2. Operate console and cab lighting.
3. Operate cooling and heating controls.
4. Identify and describe operation of emergency power cutoff.
5. Read altimeter, wind instruments and clock information.
6. Ensure NAVAID monitors are operating properly, read indicators, and
identify equipment status.
7. Operate the weather reporting monitor to extract information.
8. Operate ALDIS lamp.
9. Operate PA system.
10. Operate traffic tabulators.
11. Operate BRANDS/BRITE control panel and display.
12. Operate the tower display workstation (TDW)
INSTRUCTOR. BI
PREREQUISITE. None.
Local Qualification Standards
KNOWLEDGE. Pass a written examination encompassing the requirement with a
minimum score of 80%.
SKILLS AND ABILITIES
Skill/Ability Date OJTI
Demonstrate the ability to configure airfield
lighting.
Demonstrate the ability to operate console and cab
lighting.
Demonstrate the ability to operate cooling and
heating controls.
Demonstrate the use of Emergency Power Cutoff
equipment.
Demonstrate the ability to read altimeter, wind,
weather and clock information from the VIDS.
Demonstrate the skill to operate the ALDIS lamp.
Individual has satisfactorily completed all LQS requirements for LTG 22:
Date: _____________
Trainee: ___________________________ Signature: ________________________
FWO/Crew Chief Signature _______________________________
LTG 25 – COMMUNICATIONS EQUIPMENT (COMM-2206)
Lesson Topic Guide
GOAL. Operate control tower communications equipment.
REQUIREMENT. While in a control tower, operate the following communications
equipment:
1. Transmitter/receiver control panel.
2. Backup/emergency transmitter/receiver location and controls.
3. Emergency alert system.
4. Intercom units.
5. P.A. system.
6. Telephones.
7. Aldis lamp.
8. VIDS
INSTRUCTOR. BI.
PREREQUISITE. None.
Local Qualification Standards
KNOWLEDGE. Pass a written examination encompassing the requirement with a
minimum score of 80%.
SKILLS AND ABILITIES
Skill/Ability Date OJTI
Demonstrate ability to operate the
transmitter/receiver control panel.
Demonstrate the ability to locate the wind and
altimeter.
Demonstrate the proper use of local time and zulu
time.
Demonstrate the skill to use the ATIS.
Demonstrate the ability to properly record an ATIS
broadcast.
Conduct a proper position relief.
Demonstrate the proper use of position logs
(VIDS/paper) to sign on and off.
Demonstrate the ability to update status boards.
Demonstrate the ability to signal vehicles with a
light gun properly.
Individual has satisfactorily completed all LQS requirements for LTG 25:
Date: _____________
Trainee: ___________________________ Signature: ________________________
FWO/Crew Chief Signature _______________________________
LTG GC26 – LOCAL PROCEDURES
Lesson Topic Guide
GOAL. Comprehend local procedures.
REQUIREMENT. Given the reference material, identify the key information
contained.
INSTRUCTOR. BI.
REFERENCE
1. Letters of Agreement.
ZDC, MCABE, 2d MAW Stereo Plans
ZDC, MAG-14, NKT Stereo Routes
2. Facility Manual
2-608 Local Frequencies
Local Control
Ground Control
Clearance Delivery
Metro
Base Operations
5-103 FOD Walks
5-104 FOD and Helicopters
5-105 FOD Sweepers
5-204 Ground Control
5-301 Movement Areas
5-417 Taxi Restrictions
5-429 Stereo Routes and VFR Flight Guarding
7-301 Airfield Lighting and Control System
3. Airfield Operations Manual
3.2.c. Quiet Hours
3.4. Taxi Instructions
3.10.f. Helicopter/Tilt Rotor Operating Procedures
3.16. Dangerous/Hazardous Cargo
3.20. Hot Brakes
3.21. Suspension of Refueling and Ordnance Operations During
Electrical Storms
3.22. Personnel and Vehicle Restrictions
Local Qualification Standards
KNOWLEDGE. Pass a written examination encompassing the requirement with a
minimum score of 80%.
SKILLS AND ABILITIES
Skill/Ability Date OJTI
Individual has satisfactorily completed all LQS requirements for LTG 26:
Date: _____________
Trainee: ___________________________ Signature: ________________________
FWO/Crew Chief Signature _______________________________
LTG 27 – BASIC INSTRUCTOR (IUT-5000/5010/5020)
Lesson Topic Guide
GOAL.
1. Introduce principles of instruction.
2. Understand the structure of an event.
3. Conduct a period of instruction on a T&R event.
REQUIREMENT.
1. Given the reference, the BIUT will demonstrate the following with the
assistance of a unit instructor:
a. Introduce/discuss/demonstrate instruction techniques.
b. Introduce/discuss/demonstrate class management techniques.
(1) How to use class resources to communicate with the student.
(2) How to properly organize the class for effective instruction.
c. Introduce/discuss/demonstrate how to prepare for a period of
instruction.
(1) Schedule the class.
(2) Prepare/access the training materials for the class.
(3) Prepare the evaluation form to be used to evaluate the students
event performance, as applicable.
2. Using the community T&R manual, discuss the following with an instructor:
a. State the purpose of a T&R event.
b. Describe the structure of a T&R event and explain the purpose and
content for each event section.
c. Using the given event, explain each section as it pertains to the
event.
(1) Explain the purpose and content of the goal.
(2) Explain the requirement condition and performance steps for the
event and what needs to be done to prepare to instruct the event.
(3) Explain how the event performance standard is measured and when
the event has been completed.
(4) State who can instruct the event.
(5) State the event prerequisite and how to verify that it was
completed.
(6) Explain how the external syllabus support requirement will be
resourced.
(7) State the references required and how each would be used to train
the event.
3. The BIUT, under the supervision of an instructor, will learn how to
conduct a period of instruction on an event selected by the instructor. The
event must be one the BIUT is current and proficient in. The BIUT will be
able to:
a. State the instructor responsibilities.
b. Define the purpose and content of a T&R event per the aviation T&R
program manual.
c. Prepare to train the event.
(1) Review the trainee’s PR to identify required training for the
event selected.
(2) Ensure the student has met prerequisites for the event to be
trained.
(3) Develop a student training plan to ensure progression per this
manual.
(4) Schedule the training event (facilities and students).
(5) Gather the resources necessary to conduct the training
(instructional materials, references and equipment).
(6) Prepare an evaluation form for each student to be evaluated.
d. Conduct training on the event selected:
(1) Ensure all training resources are properly staged/equipment if
set up properly for training.
(2) Instruct the student in a thorough manner so as to cover all
requirements for the event.
(3) Ensure continuous, objective assessment of the students’ progress
during training.
e. Assess student performance:
(1) Assess the students’ performance to the performance standard.
(2) Correct student deficiencies in a timely manner and provide the
student feedback.
(3) Complete the evaluation form for each student trained.
(4) Debrief students on their performance and provide corrective
action.
f. Route evaluation form, as required.
INSTRUCTOR. BI.
REFERENCE. NAVMC 3500.14
Local Qualification Standards
KNOWLEDGE. There is no test for LTG 27.
SKILLS AND ABILITIES
Skill/Ability Date SI
Demonstrate an understanding of the principles of
instruction verbally.
Physically demonstrate proper instruction and
classroom techniques.
Demonstrate event required knowledge.
Demonstrate how to schedule and prepare to instruct
an event.
Without the aid of references and during a
discussion session, demonstrate an understanding of
the structure of T&R events.
Conduct a period of instruction on a T&R event.
Individual has satisfactorily completed all LQS requirements for LTG 27:
Date: _____________
Trainee: ___________________________ Signature: ________________________
FWO/Crew Chief Signature _______________________________
Section VII PROGRESSION BENCHMARKS
1. Orientation.
COMPLETION REQUIRED PRIOR TO BEGINNING OJT
Task T&R Event Completion
Date
OJTI
Initials
ORNT 1 Test NA
ORNT 2 Test ACAD-0500
ORNT 3 Test ACAD-0501
ORNT 4 Test ACAD-0502
ORNT 5 Test ACAD-0503
ORNT 6 Test ACAD-0504
ORNT 7 Test ACAD-0505
ORNT 8 Test ACAD-0506
ORNT 9 Test ACAD-0507
ORNT 10 Test ACAD-0508
ORNT 11 Test ACAD-0509
2. Radar Flight Data.
COMPLETION REQUIRED PRIOR TO BEGINNING OJT
Task Completion
Date
OJTI
Initials
5 Hour of On-the-Job Familiarization
COMPLETION REQUIRED AT 25% OF OJT TIME LIMIT
Task T&R Event Completion
Date
OJTI
Initials
LTG 1 Test ACAD-0520
LTG 2 Test ACAD-0521
LTG 3 Test ACAD-0522
LTG 4 Test ACAD-0523
LTG 13 Test ACAD-0532
LTG 15 Test ACAD-0534
LTG 19 Test ACAD-0538
LTG 23 Practical Application EQPT-2018
LTG 24 Practical Application EQPT-2019
LTG 25 Practical Application COMM-2206
LTG 26 Test NA
ADDITIONAL TASKS THAT MAY BE REQUIRED
Task Completion Date OJTI
Initials
50% Performance Skill Check
50% Tape Talk
75% Performance Skill Check
100% Performance Skill Check
Qualification Process
Recommended By Primary OJT Instructor (Signature)
Date:
Final Examination Complete (Signature)
Date:
MACCS Qualification Form Complete - Examiner (Signature)
Date:
3. Radar Final Control.
COMPLETION REQUIRED PRIOR TO BEGINNING OJT
Task Completion
Date
OJTI
Initials
5 Hour of On-the-Job Familiarization
COMPLETION REQUIRED AT 25% OF OJT TIME LIMIT
Task T&R Event Completion
Date
OJTI
Initials
LTG 1 Test ACAD-0520
LTG 2 Test ACAD-0521
LTG 3 Test ACAD-0522
LTG 4 Test ACAD-0523
LTG 13 Test ACAD-0532
LTG 14 Test ACAD-0533
LTG 15 Test ACAD-0534
LTG 19 Test ACAD-0538
LTG 23 Practical Application EQPT-2018
LTG 25 Practical Application COMM-2206
LTG 26 Test NA
LTG 27 Practical Application IUT-5000
ADDITIONAL TASKS THAT MAY BE REQUIRED
Task Completion Date OJTI
Initials
50% Performance Skill Check
50% Tape Talk
75% Performance Skill Check
100% Performance Skill Check
Qualification Process
Recommended By Primary OJT Instructor (Signature)
Date:
Final Examination Complete (Signature)
Date:
MACCS Qualification Form Complete - Examiner (Signature)
Date:
4. Tower Flight Data.
COMPLETION REQUIRED PRIOR TO BEGINNING OJT
Task Completion
Date
OJTI
Initials
5 Hour of On-the-Job Familiarization
COMPLETION REQUIRED AT 25% OF OJT TIME LIMIT
Task T&R Event Completion
Date
OJTI
Initials
LTG 1 Test ACAD-0520
LTG 2 Test ACAD-0521
LTG 3 Test ACAD-0522
LTG 4 Test ACAD-0523
LTG 22 Practical Application EQPT-2003
LTG 24 Practical Application EQPT-2019
LTG 25 Practical Application COMM-2206
LTG 26
ADDITIONAL TASKS THAT MAY BE REQUIRED
Task Completion Date OJTI
Initials
50% Performance Skill Check
50% Tape Talk
75% Performance Skill Check
100% Performance Skill Check
Qualification Process
Recommended By Primary OJT Instructor (Signature)
Date:
Final Examination Complete (Signature)
Date:
MACCS Qualification Form Complete - Examiner (Signature)
Date:
5. Tower Ground Control.
COMPLETION REQUIRED PRIOR TO BEGINNING OJT
Task Completion
Date
OJTI
Initials
5 Hour of On-the-Job Familiarization
COMPLETION REQUIRED AT 25% OF OJT TIME LIMIT
Task T&R Event Completion
Date
OJTI
Initials
LTG 1 Test ACAD-0520
LTG 2 Test ACAD-0521
LTG 3 Test ACAD-0522
LTG 4 Test ACAD-0523
LTG 5 Test ACAD-0524
LTG 6 Test ACAD-0525
LTG 8 Test ACAD-0527
LTG 9 Test ACAD-0528
LTG 22 Practical Application EQPT-2003
LTG 25 Practical Application COMM-2206
LTG 26 Test
LTG 27 IUT-5000
ADDITIONAL TASKS THAT MAY BE REQUIRED
Task Completion Date OJTI
Initials
50% Performance Skill Check
50% Tape Talk
75% Performance Skill Check
100% Performance Skill Check
Qualification Process
Recommended By Primary OJT Instructor (Signature)
Date:
Final Examination Complete (Signature)
Date:
MACCS Qualification Form Complete - Examiner (Signature)
Date:
Section VIII TRAINING AND READINESS EVENTS
T&R Event Codes U 1 2 3 4 Comments
ACAD-0500
ACAD-0501
ACAD-0502
ACAD-0503
ACAD-0504
ACAD-0505
ACAD-0506
ACAD-0507
ACAD-0508
ACAD-0509
ORNT-2000
Evaluator’s Overall Comments (Comments on the trainees overall performance to include trends and recommendations for improvement)
Legend
U = UNSAT Unsafe or complete lack of ability and/or knowledge. Requires substantial input from the evaluator for mission accomplishment.
1 Limited proficiency, does not meet the standard. Requires frequent input from the evaluator.
2 Capable. Recognizes and corrects errors. Requires occasional input from the evaluator.
3 Proficient. Correct, efficient, skillful, and without hesitation. Requires minimal input from the evaluator.
4 Unusually high degree of ability. Requires no input from evaluator
Trainee Endorsement
Trainee Signature _________________________________________________________________ Date __________________
I have read and discussed this evaluation with the evaluator and I understand its contents.
Approval Process
Evaluator Signature _________________________________________________________________ Date ________________
I certify that the trainee has completed the training as described on this form.
OIC/SNCOIC Signature _______________________________________________________________ Date _________________
WTTP Signature ____________________________________________________________________ Date __________________
Evaluation form is correct, administrative actions have been completed, and event code(s) have been logged in M-SHARP.
MACCS QUALIFICATION FORM
The MACCS T&R qualification form is used to document all event training that results in a qualification. The qualification form is a tool that provides the evaluator a medium to document a trainee’s qualification skill check. Both the trainee and evaluator will sign this form. The WTTP Section will ensure this form is administratively correct and logged in M-SHARP.
Trainee Rank / Name: Billet:
Exercise / Operation: Date:
Evaluator's Rank/Name: Evaluator’s Billet / DESG:
T&R Event Codes U 1 2 3 4 Comments
ACAD-0520
ACAD-0521
ACAD-0522
ACAD-0523
ACAD-0532
ACAD-0534
ACAD-0538
EQPT-2018
EQPT-2019
COMM-2206
RFD-3700
QUAL-6103
Evaluator’s Overall Comments (Comments on the trainees overall performance to include trends and recommendations for improvement)
Legend
U = UNSAT Unsafe or complete lack of ability and/or knowledge. Requires substantial input from the evaluator for mission accomplishment.
1 Limited proficiency, does not meet the standard. Requires frequent input from the evaluator.
2 Capable. Recognizes and corrects errors. Requires occasional input from the evaluator.
3 Proficient. Correct, efficient, skillful, and without hesitation. Requires minimal input from the evaluator.
4 Unusually high degree of ability. Requires no input from evaluator
Trainee Endorsement
Trainee Signature _________________________________________________________________ Date __________________
I have read and discussed this evaluation with the evaluator and I understand its contents.
Approval Process
Evaluator Signature _________________________________________________________________ Date ________________
I certify that the trainee has completed the training as described on this form.
OIC/SNCOIC Signature _______________________________________________________________ Date _________________
WTTP Signature ____________________________________________________________________ Date __________________
Evaluation form is correct, administrative actions have been completed, and event code(s) have been logged in M-SHARP.
MACCS QUALIFICATION FORM
The MACCS T&R qualification form is used to document all event training that results in a qualification. The qualification form is a tool that provides the evaluator a medium to document a trainee’s qualification skill check. Both the trainee and evaluator will sign this form. The WTTP Section will ensure this form is administratively correct and logged in M-SHARP.
Trainee Rank / Name: Billet:
Exercise / Operation: Date:
Evaluator's Rank/Name: Evaluator’s Billet / DESG:
T&R Event Codes U 1 2 3 4 Comments
ACAD-0520
ACAD-0521
ACAD-0522
ACAD-0523
ACAD-0532
ACAD-0533
ACAD-0534
ACAD-0538
EQPT-2018
COMM-2206
IUT-5000
IUT-5010
IUT-5020
RFC-3710
QUAL-6113
Evaluator’s Overall Comments (Comments on the trainees overall performance to include trends and recommendations for improvement)
Legend
U = UNSAT Unsafe or complete lack of ability and/or knowledge. Requires substantial input from the evaluator for mission accomplishment.
1 Limited proficiency, does not meet the standard. Requires frequent input from the evaluator.
2 Capable. Recognizes and corrects errors. Requires occasional input from the evaluator.
3 Proficient. Correct, efficient, skillful, and without hesitation. Requires minimal input from the evaluator.
4 Unusually high degree of ability. Requires no input from evaluator
Trainee Endorsement
Trainee Signature _________________________________________________________________ Date __________________
I have read and discussed this evaluation with the evaluator and I understand its contents.
Approval Process
Evaluator Signature _________________________________________________________________ Date ________________
I certify that the trainee has completed the training as described on this form.
OIC/SNCOIC Signature _______________________________________________________________ Date _________________
WTTP Signature ____________________________________________________________________ Date __________________
Evaluation form is correct, administrative actions have been completed, and event code(s) have been logged in M-SHARP.
MACCS QUALIFICATION FORM
The MACCS T&R qualification form is used to document all event training that results in a qualification. The qualification form is a tool that provides the evaluator a medium to document a trainee’s qualification skill check. Both the trainee and evaluator will sign this form. The WTTP Section will ensure this form is administratively correct and logged in M-SHARP.
Trainee Rank / Name: Billet:
Exercise / Operation: Date:
Evaluator's Rank/Name: Evaluator’s Billet / DESG:
T&R Event Codes U 1 2 3 4 Comments
ACAD-0520
ACAD-0521
ACAD-0522
ACAD-0523
EQPT-2003
EQPT-2019
COMM-2206
CD-3610
QUAL-6160
TFD-3600
QUAL-6153
Evaluator’s Overall Comments (Comments on the trainees overall performance to include trends and recommendations for improvement)
Legend
U = UNSAT Unsafe or complete lack of ability and/or knowledge. Requires substantial input from the evaluator for mission accomplishment.
1 Limited proficiency, does not meet the standard. Requires frequent input from the evaluator.
2 Capable. Recognizes and corrects errors. Requires occasional input from the evaluator.
3 Proficient. Correct, efficient, skillful, and without hesitation. Requires minimal input from the evaluator.
4 Unusually high degree of ability. Requires no input from evaluator
Trainee Endorsement
Trainee Signature _________________________________________________________________ Date __________________
I have read and discussed this evaluation with the evaluator and I understand its contents.
Approval Process
Evaluator Signature _________________________________________________________________ Date ________________
I certify that the trainee has completed the training as described on this form.
OIC/SNCOIC Signature _______________________________________________________________ Date _________________
WTTP Signature ____________________________________________________________________ Date __________________
Evaluation form is correct, administrative actions have been completed, and event code(s) have been logged in M-SHARP.
MACCS QUALIFICATION FORM
The MACCS T&R qualification form is used to document all event training that results in a qualification. The qualification form is a tool that provides the evaluator a medium to document a trainee’s qualification skill check. Both the trainee and evaluator will sign this form. The WTTP Section will ensure this form is administratively correct and logged in M-SHARP.
Trainee Rank / Name: Billet:
Exercise / Operation: Date:
Evaluator's Rank/Name: Evaluator’s Billet / DESG:
T&R Event Codes U 1 2 3 4 Comments
ACAD-0520
ACAD-0522
ACAD-0523
ACAD-0524
ACAD-0525
ACAD-0527
ACAD-0528
EQPT-2003
EQPT-2004
COMM-2206
IUT-5000
IUT-5010
IUT-5020
TGC-3620
QUAL-6173
Evaluator’s Overall Comments (Comments on the trainees overall performance to include trends and recommendations for improvement)
Legend
U = UNSAT Unsafe or complete lack of ability and/or knowledge. Requires substantial input from the evaluator for mission accomplishment.
1 Limited proficiency, does not meet the standard. Requires frequent input from the evaluator.
2 Capable. Recognizes and corrects errors. Requires occasional input from the evaluator.
3 Proficient. Correct, efficient, skillful, and without hesitation. Requires minimal input from the evaluator.
4 Unusually high degree of ability. Requires no input from evaluator
Trainee Endorsement
Trainee Signature _________________________________________________________________ Date __________________
I have read and discussed this evaluation with the evaluator and I understand its contents.
Approval Process
Evaluator Signature _________________________________________________________________ Date ________________
I certify that the trainee has completed the training as described on this form.
OIC/SNCOIC Signature _______________________________________________________________ Date _________________
WTTP Signature ____________________________________________________________________ Date __________________
Evaluation form is correct, administrative actions have been completed, and event code(s) have been logged in M-SHARP.
MACCS QUALIFICATION FORM
The MACCS T&R qualification form is used to document all event training that results in a qualification. The qualification form is a tool that provides the evaluator a medium to document a trainee’s qualification skill check. Both the trainee and evaluator will sign this form. The WTTP Section will ensure this form is administratively correct and logged in M-SHARP.
Trainee Rank / Name: Billet:
Exercise / Operation: Date:
Evaluator's Rank/Name: Evaluator’s Billet / DESG: