ATT Product Service Co., Ltd · 2013. 12. 31. · S08-006-0085-00700 8.5 0.01-0.70...

NO.L3098

Report No.: 13EAB12021 21 1 of 54

ATT Product Service Co., Ltd (CBTL Lab of UL/Demko) No. 3, ChangLianShan Industrial Park, ChangAn Town, DongGuan City, GuangDong, China. Phone: 86-769-8509 8000; Fax: 86-769-8509 8777 E-mail:[email protected] Rev. 1.0

EMC TEST REPORT

For Electromagnetic Interference of

Report Reference No........................: 13EAB12021 21

Date of issue.....................................: 2013-12-13

Testing Laboratory ............................: ATT Product Service Co., Ltd.

Address.............................................: No. 3, ChangLianShan Industrial Park, ChangAn Town, DongGuan City, GuangDong, China.

Applicant’s name ..............................: Keen Ocean Industrial Limited

Address.............................................: Room 3405.34/F.,Cable TV Tower ,9 Hoi Shing Road.Tsuen Wan,N,T.,Hong Kong

Manufacturer ....................................: Keen Ocean Industrial Ltd

Test specification:

Test item description.........................: AC/DC Adaptor

Trade Mark .......................................: --

Model/Type reference .....................: S08-006-YYYY-ZZZZZ Refer to page 5 for details

Ratings..............................................: I/P: 100-240Vac, 50/60Hz, 0.2A Max

O/P: Refer to page 5 for details.

Responsible Engineer Approved by

（Mike Yang/ Engineer）（Tomy Wu /EMC Manager）

NO.L3098

Report No.: 13EAB12021 21 2 of 54


Table of Contents

Page

1 . CERTIFICATION 4

1.1 GENERAL DESCRIPTION OF EUT 5

2 . SUMMARY OF TEST RESULTS 6

2.1 MEASUREMENT UNCERTAINTY 7

2.2 DESCRIPTION OF TEST MODES 8

2.3 BLOCK DIGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED 9

3 . EMC EMISSION TEST 10

3.1 CONDUCTED EMISSION MEASUREMENT 10

3.1.1 POWER LINE CONDUCTED EMISSION 10

3.1.2 MEASUREMENT INSTRUMENTS LIST 10

3.1.3 TEST PROCEDURE 11

3.1.4 DEVIATION FROM TEST STANDARD 11

3.1.5 TEST SETUP 11

3.1.6 EUT OPERATING CONDITIONS 11

3.1.7 TEST RESULTS 12

3.2 RADIATED EMISSION MEASUREMENT 18

3.2.1 LIMITS OF RADIATED EMISSION MEASUREMENT 18




3.2.5 TEST SETUP 20



3.3 HARMONICS CURRENT MEASUREMENT 27

3.4 VOLTAGE FLUCTUATION AND FLICKS MEASUREMENT 28

3.4.1 LIMITS OF VOLTAGE FLUCTUATION AND FLICKSMEASUREMENT 28




3.4.5 TESTSETUP 29



4 . EMC IMMUNITY TEST 31

4.1 STANDARD COMPLIANCE/SERVRITY LEVEL/CRITERIA 31

4.2 GENERAL PERFORMANCE CRITERIA 32

4.3 GENERAL PERFORMANCE CRITERIA TEST SETUP 32

4.4 ESD TESTING 33

4.4.1 TEST SPECIFICATION 33

NO.L3098

Report No.: 13EAB12021 21 3 of 54


Table of Contents

Page

4.4.2 MEASUREMENT INSTRUMENTS 33



4.4.5 TEST SETUP 34


4.5 RS TESTING 36





4.5.5 TEST SETUP 37


4.6 EFT/BURST TESTING 39





4.6.5 TEST SETUP 40


4.7 SURGE TESTING 42





4.7.5 TEST SETUP 43


4.8 INJECTION CURRENT TESTING 45





4.8.5 TEST SETUP 46


4.9 VOLTAGE INTERRUPTION/DIPS TESTING 48





4.9.5 TEST SETUP 49


5 . EUT TEST PHOTO 51

NO.L3098

Report No.: 13EAB12021 21 4 of 54


1. CERTIFICATION

Testing Laboratory ............................: ATT Product Service Co., Ltd.

Address.............................................: No. 3, ChangLianShan Industrial Park, ChangAn Town, DongGuan City, GuangDong, China.

Applicant’s name ..............................: Keen Ocean Industrial Limited

Address.............................................: Room 3405.34/F.,Cable TV Tower ,9 Hoi Shing Road.Tsuen Wan,N,T.,Hong Kong

Manufacturer ....................................: Same as applicant

Address……………………………: Same as applicant

Factory…………………………….: HE YUAN SKY WEALTH ELECTRONIC AND PLASTIC CO LTD

Address……………………………: HI-TECH DEVELOPMENT ZONE HEYUAN GUANGDONG CHINA 517000

Test specification:

Test item description.........................: AC/DC Adaptor

Trade Mark .......................................: --

Model/Type reference .....................: S08-006-YYYY-ZZZZZ Refer to page 5 for details

Test Sample: S08-006-0050-01200, S08-006-0120-00500

Ratings..............................................: I/P: 100-240Vac, 50/60Hz, 0.2A Max

O/P: Refer to page 5 for details.

Tested AC/DC Adaptor: AC 230V 50Hz

Standards ........................................: EN 55022:2010+AC:2011 EN 55024:2010 EN 61000-3-2:2006+A1:2009+A2:2009 EN 61000-3-3:2008

The device described above was tested by ATT Product Service Co., Ltd to determine

the maximum emission levels emanated from the device and severity levels of the device

endure and its performance criterion. The measurement results are contained in this test

report and ATT Product Service Co., Ltd assumes full responsibility for the accuracy and

completeness of these measurements. This report shows the EUT is technically compliance

with the above official standards.

This report applies to the above sample only and shall not be reproduced in part without written

approval of ATT Product Service Co., Ltd.

NO.L3098

Report No.: 13EAB12021 21 5 of 54


1.1 General product information: Model List:

S08-006-YYYY-ZZZZZ YYYY=0050-0120 for output voltage; ZZZZZ=00500-01200 for output current.

Model No Voltage(V) Current(A)

S08-006-0050-01200 5 0.01-1.20

S08-006-0055-01090 5.5 0.01-1.09

S08-006-0060-01000 6.0 0.01-1.0

S08-006-0065-00920 6.5 0.01-0.92

S08-006-0080-00850 7.0 0.01-0.85

S08-006-0075-00800 7.5 0.01-0.80

S08-006-0080-00750 8.0 0.01-0.75

S08-006-0081-00740 8.1 0.01-0.74

S08-006-0082-00730 8.2 0.01-0.73

S08-006-0085-00700 8.5 0.01-0.70

S08-006-0090-00660 9.0 0.01-0.66

S08-006-0095-00630 9.5 0.01-0.63

S08-006-0100-00600 10.0 0.01-0.60

S08-006-0105-00570 10.5 0.01-0.57

S08-006-0110-00540 11.0 0.01-0.54

S08-006-0115-00520 11.5 0.01-0.52

S08-006-0120-00500 12.0 0.01-0.50

NO.L3098

Report No.: 13EAB12021 21 6 of 54


2. SUMMARY OF TEST RESULTS

Test procedures according to the technical standards:

EMC Emission

Standard Test Item Limit Judgment Remark

Conducted Emission Class B PASS

EN 55022:2010+AC:2011 Radiated Emission Class B PASS

EN61000-3-2:2006+A1:2009+A2:2009

Harmonic Current Emission Class A PASS

EN61000-3-3:2008 Voltage Fluctuations & Flicker ------ PASS

EMC Immunity (EN 55024: 2010)

Section Test Item Performance

Criteria Judgment Remark

EN 61000-4-2:2009 Electrostatic Discharge B PASS

EN 61000-4-3: 2006+A1:2008+A2:2010

RF electromagnetic field A PASS

EN 61000-4-4: 2012 Fast transients B PASS

EN 61000-4-5: 2006 Surges B PASS

EN 61000-4-6: 2009 Injected Current A PASS

EN 61000-4-8: 2010 Power Frequency Magnetic

Field A N/A

EN 61000-4-11:2004 Volt. Interruptions Volt. Dips B / C / C NOTE (3)

PASS

NOTE:

(1)” N/A” denotes test is not applicable in this Test Report

(2) The power consumption of EUT is less than 75W and no Limits apply.

(3) Voltage dip: ＞95% reduction – Performance Criteria B

Voltage dip: 30% reduction – Performance Criteria C

Voltage Interruption: ＞95% reduction – Performance Criteria C

NO.L3098

Report No.: 13EAB12021 21 7 of 54


2.1 MEASUREMENT UNCERTAINTY The reported uncertainty of measurement y ± U，where expended uncertainty U is based on a standard

uncertainty multiplied by a coverage factor of k=2，providing a level of confidence of approximately 95%. A. Conducted Measurement :

Test Site Method Measurement Frequency Range U，(dB) NOTE C01 ANSI 150 KHz ~ 30MHz 1.94

B. Radiated Measurement :

Test Site Method Measurement Frequency RangeAnt. H / V

U，(dB) NOTE

OS02 ANSI 30MHz ~ 200MHz V 3.82 30MHz ~ 200MHz H 3.60 200MHz ~ 1,000MHz V 3.86 200MHz ~ 1,000MHz H 3.94

NO.L3098

Report No.: 13EAB12021 21 8 of 54


2.2 DESCRIPTION OF TEST MODES

To investigate the maximum EMI emission characteristics generates from EUT, the test system was pre-scanning tested base on the consideration of following EUT operation mode or test configuration mode which possible have effect on EMI emission level. Each of these EUT operation mode(s) or test configuration mode(s) mentioned above was evaluated respectively.

Pretest Mode Description

Mode 1 FULL LOAD

For Conducted Test

Final Test Mode Description

Mode 1 FULL LOAD

For Radiated Test


Mode 1 FULL LOAD

For Harmonics / Flicks Test


Mode 1 FULL LOAD

For EMS Test


Mode 1 FULL LOAD

NO.L3098

Report No.: 13EAB12021 21 9 of 54


2.3 BLOCK DIGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED

E-1 EUTE-2

Dummy Load

C-1

C-1 Power Cable

NO.L3098

Report No.: 13EAB12021 21 10 of 54


3. EMC EMISSION TEST

3.1 CONDUCTED EMISSION MEASUREMENT 3.1.1 POWER LINE CONDUCTED EMISSION (Frequency Range 150KHz-30MHz)

Class A (dBuV) Class B (dBuV) FREQUENCY (MHz)

Quasi-peak Average Quasi-peak Average

0.15 -0.5 79.00 66.00 66 - 56 * 56 - 46 *

0.50 -5.0 73.00 60.00 56.00 46.00

5.0 -30.0 73.00 60.00 60.00 50.00

Note:

(1) The tighter limit applies at the band edges.

(2) The limit of " * " marked band means the limitation decreases linearly with the logarithm of the frequency in the range.

3.1.2 MEASUREMENT INSTRUMENTS LIST

Item Kind of Equipment Manufacturer Type No. Serial No. Calibrated until

1 Pulse Limiter MTS-systemtechnik MTS-IMP-13

6 261115-010-002

4 12/27/2013

2 EMI Test Receiver R&S ESCI 101308 12/27/2013

3 LISN AFJ LS16 16011103219 12/27/2013

Remark: ” N/A” denotes No Model No. , Serial No. or No Calibration specified.

NO.L3098

Report No.: 13EAB12021 21 11 of 54


3.1.3 TEST PROCEDURE

a. The EUT was placed 0.8 meters from the horizontal ground plane with EUT being connected to the power mains through a line impedance stabilization network (LISN). All other support equipments powered from additional LISN(s). The LISN provide 50 Ohm/ 50uH of coupling impedance for the measuring instrument.

b. Interconnecting cables that hang closer than 40 cm to the ground plane shall be folded back and forth in the center forming a bundle 30 to 40 cm long.

c. I/O cables that are not connected to a peripheral shall be bundled in the center. The end of the cable may be terminated, if required, using the correct terminating impedance. The overall length shall not exceed 1 m.

d. LISN at least 80 cm from nearest part of EUT chassis. e. For the actual test configuration, please refer to the related Item –EUT Test Photos.

3.1.4 DEVIATION FROM TEST STANDARD No deviation

3.1.5 TEST SETUP

3.1.6 EUT OPERATING CONDITIONS

The EUT exercise program used during radiated and/or conducted emission measurement was designed to exercise the various system components in a manner similar to a typical use.

NO.L3098

Report No.: 13EAB12021 21 12 of 54


3.1.7 TEST RESULTS

EUT： AC/DC Adaptor Model No. ： S08-006-0050-01200

Temperature： 26℃ Relative Humidity： 48 %

Pressure： 1008 hPa Test Power ： AC 230V/50Hz

Test Mode ： Full Load

Remark：

(1) Reading in which marked as QP means measurements by using are Quasi-Peak Mode with Detector BW=9KHz；SPA setting in RBW=10KHz,VBW =10KHz, Swp. Time = 0.3 sec./MHz. Reading in which marked as AV means measurements by using are Average Mode with instrument setting in RBW=1MHz,VBW=10Hz, Swp. Time =0.3 sec./MHz.

(2) All readings are QP Mode value unless otherwise stated AVG in column of『Note』. If the QP Mode Measured value compliance with the QP Limits and lower than AVG Limits, the EUT shall be deemed to meet both QP & AVG Limits and then only QP Mode was measured, but AVG Mode didn‘t perform.In this case, a “ * ” marked in AVG Mode column of Interference Voltage Measured.

(3) Measuring frequency range from 150KHz to 30MHz.

NO.L3098

Report No.: 13EAB12021 21 13 of 54


NO.L3098

Report No.: 13EAB12021 21 14 of 54


NO.L3098

Report No.: 13EAB12021 21 15 of 54






Remark：

(1) Reading in which marked as QP means measurements by using are Quasi-Peak Mode with Detector BW=9KHz；SPA setting in RBW=10KHz,VBW =10KHz, Swp. Time = 0.3 sec./MHz. Reading in which marked as AV means measurements by using are Average Mode with instrument setting in RBW=1MHz,VBW=10Hz, Swp. Time =0.3 sec./MHz.

(2) All readings are QP Mode value unless otherwise stated AVG in column of『Note』. If the QP Mode Measured value compliance with the QP Limits and lower than AVG Limits, the EUT shall be deemed to meet both QP & AVG Limits and then only QP Mode was measured, but AVG Mode didn‘t perform.In this case, a “ * ” marked in AVG Mode column of Interference Voltage Measured.

(3) Measuring frequency range from 150KHz to 30MHz.

NO.L3098

Report No.: 13EAB12021 21 16 of 54


NO.L3098

Report No.: 13EAB12021 21 17 of 54


NO.L3098

Report No.: 13EAB12021 21 18 of 54


3.2 RADIATED EMISSION MEASUREMENT

3.2.1 LIMITS OF RADIATED EMISSION MEASUREMENT (Below 1000MHz)

FREQUENCY (MHz) Field strengths limits at 10m

Measuring distance: dBuV/m

Field strengths limits at 3m

Measuring distance: dBuV/m

30 – 230 30 40

230 – 1000 37 47

Notes:

(1) The limit for radiated test was performed according to as following: CISPR 22/ FCC PART 15B /ICES-003.

(2) The tighter limit applies at the band edges.

(3) Emission level (dBuV/m)=20log Emission level (uV/m).

(4) The higest internal source of the EUT is less than108 MHz,the measurement shall only be Made up to 1GHz

NO.L3098

Report No.: 13EAB12021 21 19 of 54




1 Log-Bicon Antenna SCHWARZBECK VULB9168 VULB9168-192 01/03/2014

2 Pre-Amplifier HP 8447F 3113A05680 12/27/2013

3 EMI Test Receiver R&S ESCI 101307 12/27/2013

4 Spectrum Analyzer Agilent E4407B US40240708 07/17/2014

5 HORN Antenna SCHWARZBECK BBHA 9120DBBHA 9120D

1065 12/27/2013

6 PRE-Amplifier CY EMC011830 980136 12/27/2013

7 Turn Table UC UC3000 N/A N.C.R.

8 Antenna Mast UC UC3000 N/A N.C.R.

Remark: ” N/A” denotes No Model No. / Serial No. and No Calibration specified.


a. The measuring distance of at 3 m shall be used for measurements at frequency up to 1GHz. For frequencies above 1GHz, any suitable measuring distance may be used.

b. The EUT was placed on the top of a rotating table 0.8 meters above the ground at a 3m or 10 meter open area test site. The table was rotated 360 degrees to determine the position of the highest radiation.

c. The height of the equipment or of the substitution antenna shall be 0.8 m; the height of the test antenna shall vary between 1 m to 4 m. Both horizontal and vertical polarizations of the antenna are set to make the measurement.

d. The initial step in collecting conducted emission data is a spectrum analyzer peak detector mode pre-scanning the measurement frequency range. Significant peaks are then marked and then Quasi Peak detector mode re-measured.

e. If the Peak Mode measured value compliance with and lower than Quasi Peak Mode Limit, the EUT shall be deemed to meet QP Limits and then no additional QP Mode measurement performed.

f. For the actual test configuration, please refer to the related Item –EUT Test Photos.

3.2.4 DEVIATION FROM TEST STANDARD

No deviation

NO.L3098

Report No.: 13EAB12021 21 20 of 54


3.2.5 TEST SETUP


The EUT tested system was configured as the statements of 2.2 Unless otherwise a special operating condition is specified in the follows during the testing.

NO.L3098

Report No.: 13EAB12021 21 21 of 54


3.2.7 TEST RESULTS EUT： AC/DC Adaptor Model No. ： S08-006-0050-01200

Temperature： 26 ℃ Relative Humidity： 48 %



Remark：

(1) Reading in which marked as QP or Peak means measurements by using are Quasi-Peak Mode or Peak Mode with Detector BW=120KHz；SPA setting in RBW=120KHz, VBW =120KHz, Swp. Time = 0.3 sec./MHz.

(2) All readings are Peak unless otherwise stated QP in column of『Note』. Peak denotes that the Peak reading compliance with the QP Limits and then QP Mode measure-ment didn‘t perform.

(3) Measuring frequency range from 30MHz to 1000MHz. (4) If the peak scan value lower limit more than 20dB, then this signal data does not how in table.

NO.L3098

Report No.: 13EAB12021 21 22 of 54


NO.L3098

Report No.: 13EAB12021 21 23 of 54


NO.L3098

Report No.: 13EAB12021 21 24 of 54






Remark：

(1) Reading in which marked as QP or Peak means measurements by using are Quasi-Peak Mode or Peak Mode with Detector BW=120KHz；SPA setting in RBW=120KHz, VBW =120KHz, Swp. Time = 0.3 sec./MHz.

(2) All readings are Peak unless otherwise stated QP in column of『Note』. Peak denotes that the Peak reading compliance with the QP Limits and then QP Mode measure-ment didn‘t perform.

(3) Measuring frequency range from 30MHz to 1000MHz. (4) If the peak scan value lower limit more than 20dB, then this signal data does not how in table.

NO.L3098

Report No.: 13EAB12021 21 25 of 54


NO.L3098

Report No.: 13EAB12021 21 26 of 54


NO.L3098

Report No.: 13EAB12021 21 27 of 54


3.3 HARMONICS CURRENT MEASUREMENT

Current Test Result Summary (Run time)




Highest parameter values during test:

Remark: This rated power of EUT is under 75W， therefore it isn’t specified in this standard.

NO.L3098

Report No.: 13EAB12021 21 28 of 54


3.4 VOLTAGE FLUCTUATION AND FLICKS MEASUREMENT

3.4.1 LIMITS OF VOLTAGE FLUCTUATION AND FLICKSMEASUREMENT

Limits Tests

IEC555-3 IEC/EN 61000-3-2 Descriptions

Pst 1.0, Tp= 10 min. 1.0, Tp= 10 min. Short Term Flicker Indicator

Plt N/A 0.65, Tp=2 hr. Long Term Flicker Indicator

dc 3 % 3.3 % Relative Steady-State V-Chang

dmax 4 % 4 % Maximum Relative V-change

d (t) N/A 3.3% for 500 ms Relative V-change characteristic



1 TEST Equipment EMC-PARTNR HARMONIC100

0 130488 01/28/2014



a. Harmonic Current Test: Test was performed according to the procedures specified in Clause 5.0 of IEC555-2 and/or Sub-clause 6.2 of IEC/EN 61000-3-2 depend on which standard adopted for compliance measurement.

b. Fluctuation and Flickers Test: Tests was performed according to the Test Conditions/Assessment of Voltage Fluctuations specified in Clause 5.0/6.0 of IEC555-3 and/or Clause 6.0/4.0 of IEC/EN 61000-3-3 depend on which standard adopted for compliance measurement.

c. All types of harmonic current and/or voltage fluctuation in this report are assessed by direct measurement using flicker-meter.

d. For the actual test configuration, please refer to the related Item –EUT Test Photos.

3.4.4 DEVIATION FROM TEST STANDARD No deviation

NO.L3098

Report No.: 13EAB12021 21 29 of 54


3.4.5 TESTSETUP



NO.L3098

Report No.: 13EAB12021 21 30 of 54


3.4.7 TEST RESULTS





Psti and limit line European Limits

Time is too short for Plt plot Parameter values recorded during the test:

Vrms at the end of test (Volt): 229.67

Highest dt (%): 0.00 Test limit (%): 3.30 PASS

Time(mS) > dt: 0.0 Test limit (mS): 500.0 PASS

Highest dc (%): 0.00 Test limit (%): 3.30 PASS

Highest dmax (%): 0.00 Test limit (%): 4.00 PASS

Highest Pst (10 min. period): 0.001 Test limit: 1.000 PASS

Highest Plt (2 hr. period): 0.001 Test limit: 0.650 PASS

0.00

0.25

0.50

0.75

1.00

10:12:18

NO.L3098

Report No.: 13EAB12021 21 31 of 54


4. EMC IMMUNITY TEST

4.1 STANDARD COMPLIANCE/SERVRITY LEVEL/CRITERIA

Tests

Standard No.

TEST SPECIFICATION

Level

Test Mode

Test Ports

Perform.

Criteria Remark

8KV air discharge 4KV contact discharge

Direct Mode B 1. ESD IEC/EN 61000-4-2

4KV HCP discharge 4KV VCP discharge

Indirect Mode B

80 MHz to 1000 MHz 3V/m(rms), 1 KHz, 80%, AM modulated

A 2. RS

IEC/EN 61000-4-3 900 +/- 5MHz 3V/m(rms), Duty cycle 50%

Repetition frequency:200Hz

Enclosure

B

1.0KV(peak) 5/50ns Tr/Th 5KHz Repetition Freq.

AC/DC Adaptor Port

B 3. EFT/Burst

IEC/EN 61000-4-4 0.5 KV(peak) 5/50ns Tr/Th 5KHz Repetition Freq.

CTL/Signal Data Line

Port B N/A

1 KV(5P/5N) 1.2/50(8/20) Tr/Th us

L-N B 4. Surges

IEC/EN 61000-4-5 2 KV(5P/5N) 1.2/50(8/20) Tr/Th us

L-PE N-PE

B

0.15 MHz to 80 MHz 3V(rms), 1KHz 80%, AM Modulated 150 source impedance

CTL/Signal Port A N/A


AC Power Port A 5 Injected Current

IEC/EN 61000-4-6


DC Power Port A N/A

6. Power Frequency Magnetic Field

IEC/EN 61000-4-8 50 Hz, 1A/m Enclosure A N/A

7. Volt. Interruptions Volt. Dips

IEC/EN 61000-4-11

Voltage dip＞95% / 30% Interruption＞95%

＜5% / 70%

＜5%

B / C

C

* Remark:

(1) :

“N/A”: denotes test is not applicable in this Test Report.

NO.L3098

Report No.: 13EAB12021 21 32 of 54


4.2 GENERAL PERFORMANCE CRITERIA

According to EN55024 standard, the general performance criteria as following:

Criterion A

The equipment shall continue to operate as intended without operator intervention. No degradation of performance or loss of function is allowed below a performance level specified by the manufacturer when the equipment is used as intended. The performance level may be replaced by a permissible loss of performance. If the minimum performance level or the permissible performance loss is not specified by the manufacturer, then either of these may be derived from the product description and documentation, and by what the user product description and documentation, and by what the user may reasonably expect from the equipment if used as intended.

Criterion B

After the test, the equipment shall continue to operate as intended without operator Intervention. No degradation of performance or loss of function is allowed, after the application of the phenomenon below a performance level specified by the manufacturer, when the equipment is used as intended. The performance level may be replaced by a permissible loss of performance. During the test, degradation of performance is allowed. However, no change of operating state if stored data allowed to persist after the test. If the minimum performance level (or the permissible performance loss ) is not specified by the manufacturer, then either of these may be derived from the product description and documentation, and by what the user may reasonably expect from the equipment if used as intended.

Criterion C

Loss of function is allowed, provided the function is self-recoverable, or can be restored by the operation of the controls by the user in accordance with the manufacturer’s instructions. Functions, and/or information stored in non-volatile memory, or protected by a battery backup, shall not be lost.

4.3 GENERAL PERFORMANCE CRITERIA TEST SETUP


NO.L3098

Report No.: 13EAB12021 21 33 of 54


4.4 ESD TESTING

4.4.1 TEST SPECIFICATION

Basic Standard: IEC/EN 61000-4-2 Discharge Impedance: 330 ohm / 150 pF Required Performance B Discharge Voltage: Air Discharge：2kV/4kV/8kV (Direct)

Contact Discharge：2kV/4kV (Direct/Indirect)

Polarity: Positive & Negative Number of Discharge: Air Discharge: min. 20 times at each test point

Contact Discharge: min. 200 times in total Discharge Mode: Single Discharge Discharge Period: 1 second minimum

4.4.2 MEASUREMENT INSTRUMENTS


1 ESD Gun NOISEKEN ESS-2002 ESS0625214 12/28/2013



The test generator necessary to perform direct and indirect application of discharges to the EUT in the following manner:

a. Contact discharge was applied to conductive surfaces and coupling planes of the EUT. During the test, it was performed with single discharges. For the single discharge time between successive single discharges was at least 1 second. The EUT shall be exposed to at least 200 discharges, 100 each at negative and positive polarity, at a minimum of four test points. One of the test points shall be subjected to at least 50 indirect discharges to the center of the front edge of the horizontal coupling plane. The remaining three test points shall each receive at least 50 direct contact discharges. If no direct contact test points are available, then at least 200 indirect discharges shall be applied in the indirect mode. Test shall be performed at a maximum repetition rate of one discharge per second. Vertical Coupling Plane (VCP): The coupling plane, of dimensions 0.5m x 0.5m, is placed parallel to, and positioned at a distance 0.1m from, the EUT, with the Discharge Electrode touching the coupling plane. The four faces of the EUT will be performed with electrostatic discharge. Horizontal Coupling Plane (HCP): The coupling plane is placed under to the EUT. The generator shall be positioned vertically at a distance of 0.1m from the EUT, with the Discharge Electrode touching the coupling plane. The four faces of the EUT will be performed with electrostatic discharge.

b. Air discharges at insulation surfaces of the EUT. It was at least ten single discharges with positive and negative at the same selected point.

c. For the actual test configuration, please refer to the related Item –EUT Test Photos.

NO.L3098

Report No.: 13EAB12021 21 34 of 54



No deviation

4.4.5 TEST SETUP

Note:

TABLE-TOP EQUIPMENT

The configuration consisted of a wooden table 0.8 meters high standing on the Ground Reference Plane. The GRP consisted of a sheet of aluminum at least 0.25mm thick, and 2.5 meters square connected to the protective grounding system. A Horizontal Coupling Plane (1.6m x 0.8m) was placed on the table and attached to the GRP by means of a cable with 940k total impedance. The equipment under test, was installed in a representative system as described in section 7 of IEC /EN 61000-4-2, and its cables were placed on the HCP and isolated by an insulating support of 0.5mm thickness. A distance of1-meter minimum was provided between the EUT and the walls of the laboratory and any other metallic structure.

FLOOR-STANDING EQUIPMENT

The equipment under test was installed in a representative system as described in section 7 of IEC/EN 61000-4-2, and its cables were isolated from the Ground Reference Plane by an insulating support of0.1-meter thickness. The GRP consisted of a sheet of aluminum that is at least 0.25mm thick, and 2.5meters square connected to the protective grounding system and extended at least 0.5 meters from the EUT on all sides.

NO.L3098

Report No.: 13EAB12021 21 35 of 54


4.4.6 TEST RESULTS





Mode Air Discharge Contact Discharge

2KV 4KV 8KV 12KV 2KV 4KV 6KV 8KV

Location P N P N P N P N P N P N P N P N

1 A A A A A A A A A A

2 A A A A A A A A A A

3 A A A A A A

4 A A A A A A

5 A A A A A A

6

7

8

9

Criteria B B

Result A A

Judgment PASS PASS

Mode HCP Discharge VCP Discharge 2KV 4KV 6KV 8KV 2KV 4KV 6KV 8KV

Location P N P N P N P N P N P N P N P N 1 A A A A A A A A 2 A A A A A A A A 3 A A A A A A A A 4 A A A A A A A A

Criteria B B Result A A

Judgment PASS PASS

Note: 1) P/N denotes the Positive/Negative polarity of the output voltage.

2) Test condition: Direct / Indirect (HCP/VCP) discharges: Minimum 50 times (Positive/Negative) at each

point. Air discharges: Minimum 10 times (Positive/Negative) at each point.

3) Test location(s) in which discharge (Air and contact discharge) to be applied illustrated by photos

shown in next page(s)

4) The Indirect (HCP/VCP) discharges description of test point as following: 1.left side 2.right side 3.front side 4.rear side

5) N/A - denotes test is not applicable in this test report

6) Criteria B: The EUT function loss during the test, but self-recoverable after the test.

NO.L3098

Report No.: 13EAB12021 21 36 of 54


4.5 RS TESTING


Basic Standard: IEC/EN 61000-4-3 Required Performance A

Frequency Range: 80 MHz - 1000 MHz Field Strength: 3 V/m Modulation: 1kHz Sine Wave, 80%, AM Modulation Frequency Step: 1 % of fundamental Polarity of Antenna: Horizontal and Vertical Test Distance: 3 m Antenna Height: 1.5 m Dwell Time: at least 3 seconds



1 Signal Generator R&S SML03 102460 11/26/2013

2 Power Amplifier A&R 150W1000M3 313157 2013-11-26

3 Log-periodic Antenna SCHWARZBECK STLP 9128E 9128E-012 2014-3-25

4 Isotropic Field Probe RadiCentre CTR1008A 05D00433SNO-0

3 2014-1-28



The EUT and support equipment, which are placed on a table that is 0.8 meter above ground and the testing was performed in a fully-anechoic chamber. The testing distance from antenna to the EUT was 3 meters. The other condition as following manner:

a. The field strength level was 3V/m.

b. The frequency range is swept from 80 MHz to 1000 MHz, with the signal 80%amplitude modulated with a 1kHz sine wave. The rate of sweep did not exceed 1.5x 10-3 decade/s. Where the frequency range is swept incrementally, the step size was 1% of fundamental.

c. The dwell time at each frequency shall be not less than the time necessary for the EUT to be able to respond.

d. The test was performed with the EUT exposed to both vertically and horizontally polarized fields on each of the four sides.

e. For the actual test configuration, please refer to the related Item –EUT Test Photos.


No deviation

NO.L3098

Report No.: 13EAB12021 21 37 of 54


4.5.5 TEST SETUP

Note:

TABLE-TOP EQUIPMENT

The EUT installed in a representative system as described in section 7 of IEC/EN 61000-4-3 was placed on a non-conductive table 0.8 meters in height. The system under test was connected to the power and signal wire according to relevant installation instructions.


The EUT installed in a representative system as described in section 7 of IEC/EN 61000-4-3 was placed on a non-conductive wood support 0.1 meters in height. The system under test was connected to the power and signal wire according to relevant installation instructions.

NO.L3098

Report No.: 13EAB12021 21 38 of 54


4.5.6 TEST RESULTS





Frequency Range

(MHz)

RF Field

Position

R.F.

Field StrengthAzimuth

Perform.

Criteria Results Judgment

0

90

180 80MHz - 1000MHz H / V

3 V/m (rms)

AM Modulated

1000Hz, 80%

270

A A PASS

Note:

1) P/N denotes the Positive/Negative polarity of the output voltage.

2) N/A - denotes test is not applicable in this test report.

3) Criteria A: There was no change operated with initial operating during the test.


5) Criteria C: The system shut down during the test.

NO.L3098

Report No.: 13EAB12021 21 39 of 54


4.6 EFT/BURST TESTING


Basic Standard: IEC/EN 61000-4-4 Required Performance B Test Voltage: Power Line：1 kV

Signal/Control Line：0.5 KV Polarity: Positive & Negative Impulse Frequency: 5 kHz Impulse Wave shape : 5/50 ns

Burst Duration: 15 ms Burst Period: 300 ms Test Duration: Not less than 1 min.



1 TEST Equipment EMC-PARTNR TRA3000 F-D-V-1501 12/27/2013



The EUT and support equipment, are placed on a table that is 0.8 meter above a metal ground plane measured 1m*1m min. and 0.65mm thick min. The other condition as following manner:

a. The length of power cord between the coupling device and the EUT should not exceed 1 meter.

b. Both positive and negative polarity discharges were applied.

c. The duration time of each test sequential was 1 minute



No deviation

NO.L3098

Report No.: 13EAB12021 21 40 of 54


4.6.5 TEST SETUP

Note:

TABLE-TOP EQUIPMENT

The configuration consisted of a wooden table (0.8m high) standing on the Ground Reference Plane. The GRP consisted of a sheet of aluminum (at least 0.25mm thick and 2.5m square) connected to the protective grounding system. A minimum distance of 0.5m was provided between the EUT and the walls of the laboratory or any other metallic structure.


The EUT installed in a representative system as described in section 7 of IEC/EN 61000-4-4 and its cables,were isolated from the Ground Reference Plane by an insulating support that is 0.1-meter thick. The GRPconsisted of a sheet of aluminum (at least 0.25mm thick and 2.5m square) connected to the protective grounding system.

NO.L3098

Report No.: 13EAB12021 21 41 of 54


4.6.6 TEST RESULTS





Mode ( X ) AC Power Line ( ) DC Power Line ( ) Signal/Control Line

Test Level 1KV 0.5KV 0.5KV

Port(s) Polarity Results Polarity Results Polarity Results

P A P P Line (L)

N A N N

P A P P Neutral (N)

N A N N

P P P Ground (PE)

N N N

P P P Signal/Control

Line N N N

Criteria B B B

Result A N/A N/A

Judgment PASS N/A N/A

Note: 1) P/N denotes the Positive/Negative polarity of the output voltage.

2) N/A - denotes test is not applicable in this test report

3) Criteria A: There was no change operated with initial operating during the test.


5) Criteria C: The system shut down during the test.

NO.L3098

Report No.: 13EAB12021 21 42 of 54


4.7 SURGE TESTING


Basic Standard: IEC/EN 61000-4-5 Required Performance B Wave-Shape: Combination Wave

1.2/50 us Open Circuit Voltage 8 /20 us Short Circuit Current

Test Voltage: Power Line：0.5 kV, 1 kV Surge Input/Output: L-N Generator Source: 2 ohm between networks Impedance: 12 ohm between network and ground Polarity: Positive/Negative Phase Angle: 0 /90/180/270 Pulse Repetition Rate: 1 time / min. (maximum) Number of Tests: 5 positive and 5 negative at selected points



1 TEST Equipment Prima SUG61005BG PR08055179 2014-07-15



a. For EUT AC/DC Adaptor:

The surge is to be applied to the EUT AC/DC Adaptor terminals via the capacitive coupling network. Decoupling networks are required in order to avoid possible adverse effects on equipment not under test that may be powered by the same lines, and to provide sufficient decoupling impedance to the surge wave. The power cord between the EUT and the coupling/decoupling networks shall be 2meters in length (or shorter).

b. For test applied to unshielded unsymmetrically operated interconnection lines of EUT:

The surge is applied to the lines via the capacitive coupling. The coupling /decoupling networks shall not influence the specified functional conditions of the EUT. The interconnection line between the EUT and the coupling/decoupling networks shall be 2 meters in length (or shorter).

c. For test applied to unshielded symmetrically operated interconnection /telecommunication lines of EUT:

The surge is applied to the lines via gas arrestors coupling. Test levels below the ignition point of the coupling arrestor cannot be specified. The interconnection line between the EUT and the coupling/decoupling networks shall be 2 meters in length (or shorter).


NO.L3098

Report No.: 13EAB12021 21 43 of 54



No deviation

4.7.5 TEST SETUP

NO.L3098

Report No.: 13EAB12021 21 44 of 54


4.7.6 TEST RESULTS





1.2/50(8/20)Ti/Th us Voltage

Wave Form

EUT Ports Tested Polarity Phase 0.5kV 1kV 1.5kV 2kV

Criteria Judgment

+/- 0 A A

+/- 90 A A

+/- 180 A A L - N

+/- 270 A A

B PASS

+/- 0

+/- 90

+/- 180 L - PE

+/- 270

B N/A

+/- 0

+/- 90

+/- 180 N - PE

+/- 270

B N/A

+/- 0

+/- 90

+/- 180 Signal Line

(N/A)

+/- 270

B N/A

+/- 0

+/- 90

+/- 180 Signal Line

(N/A)

+/- 270

B N/A

Note:


2) Polarity and Numbers of Impulses：5 Pst / Ngt at each tested mode

3) N/A - denotes test is not applicable in this Test Report

4) All voltages of the lower levels shall be satisfied

NO.L3098

Report No.: 13EAB12021 21 45 of 54


4.8 INJECTION CURRENT TESTING


Basic Standard: IEC/EN 61000-4-6 Required Performance A Frequency Range: 0.15 MHz - 80 MHz Field Strength: 3 Vr.m.s. Modulation: 1kHz Sine Wave, 80%, AM Modulation Frequency Step: 1 % of fundamental Dwell Time: at least 3 seconds



1 CONDUCTED

IMMUNITY TEST SYSTEM

FRANKONIA CIT-10 102D1253 2014-11-25

2 CDN FRANKONIA CDN M2+M3 A3011059 2014-11-25



The EUT and support equipment, are placed on a table that is 0.8 meter above a metal ground plane measured 1m*1m min. and 0.65mm thick min. The other condition as following manner:

a. The field strength level was 3V.

b. The frequency range is swept from 150 KHz to 80 MHz, with the signal 80%amplitude modulated with a 1kHz sine wave. The rate of sweep did not exceed 1.5x 10-3 decade/s. Where the frequency range is swept incrementally, the step size was 1% of fundamental.

c. The dwell time at each frequency shall be not less than the time necessary for the EUT to be able to respond.



No deviation

NO.L3098

Report No.: 13EAB12021 21 46 of 54


4.8.5 TEST SETUP

For the actual test configuration, please refer to the related Item –EUT Test Photos.

NOTE:


The equipment to be tested is placed on an insulating support of 0.1 meters height above a ground reference plane. All relevant cables shall be provided with the appropriate coupling and decoupling devices at a distance between 0.1 meters and 0.3 meters from the projected geometry of the EUT on the ground reference plane.

NO.L3098

Report No.: 13EAB12021 21 47 of 54


4.8.6 TEST RESULTS





Test Ports

(Mode)

Freq. Range MHz)

Field StrengthPerform.


Input/ Output

AC. Power Port 0.15 ---80 A A PASS

Input/ Output

DC. Power Port 0.15 --- 80 A N/A N/A

Signal Line

( N/A ) 0.15 --- 80 A N/A N/A

Signal Line

( N/A ) 0.15 --- 80

3V(rms)

AM Modulated

1000Hz, 80%

A N/A N/A

Note:


2) N/A - denotes test is not applicable in this Test Report.

NO.L3098

Report No.: 13EAB12021 21 48 of 54


4.9 VOLTAGE INTERRUPTION/DIPS TESTING


Basic Standard: IEC/EN 61000-4-11 Required Performance: B (For >95% Voltage Dips)

C (For 30% Voltage Dips) C (For >95% Voltage Interruptions)

Test Duration Time: Minimum three test events in sequence Interval between Event: Minimum ten seconds Phase Angle: 0°/45°/90°/135°/180°/225°/270°/315°/360° Test Cycle: 3 times



1 TEST Equipment EMC-PARTNR TRA3000 F-D-V-1501 12/27/2013



The EUT shall be tested for each selected combination of test levels and duration with a sequence of three dips/interruptions with intervals of 10 s minimum (between each test event). Each representative mode of operation shall be tested. Abrupt changes in supply voltage shall occur at zero crossings of the voltage waveform.


No deviation

NO.L3098

Report No.: 13EAB12021 21 49 of 54


4.9.5 TEST SETUP

For the actual test configuration, please refer to the related Item –EUT Test Photos.

NO.L3098

Report No.: 13EAB12021 21 50 of 54


4.9.6 TEST RESULTS


Temperature： 26 ℃ Relative Humidity： 48%

Pressure： 1004hPa Test Power ： AC 230V/50Hz


Voltage

Reduction Periods

Perform


Voltage dip ＞95% 0.5 B A PASS

Voltage dip 30% 25 C A PASS

Interruption＞95% 250 C C PASS

Note:


2). N/A - denotes test is not applicable in this test report.

NO.L3098

Report No.: 13EAB12021 21 51 of 54


5. EUT TEST PHOTO

Conducted Measurement Photos

Radiated Measurement Photos

NO.L3098

Report No.: 13EAB12021 21 52 of 54


ESD Measurement Photos

Surge Measurement Photos

NO.L3098

Report No.: 13EAB12021 21 53 of 54


EUT Photo

View: [ x ] general [ ] front [ ] rear [ ] right [ ] left [ ] top [ ] bottom

View: [ x ] general [ ] front [ ] rear [ ] right [ ] left [ ] top [ ] bottom

NO.L3098

Report No.: 13EAB12021 21 54 of 54


View: [ ] general [ ] front [ ] rear [ ] right [ ] left [x ] top [ ] bottom

View: [ ] general [ ] front [ ] rear [ ] right [ ] left [ ] top [x ] bottom

Date post:	23-Sep-2020
Category:	Documents
Upload:	others
View:	0 times
Download:	0 times

ATT Product Service Co., Ltd · 2013. 12. 31. · S08-006-0085-00700 8.5 0.01-0.70...

Documents