Scale: Date: Sheet: 01/06A41:

Index:Model: Serial-No.:

Paper:

AT

X F

ree Stand H

alf Rack 240

ATX Free Stand Half Rack 240 1ATX-FS-240

AT

X-F

S-240

01.10.2014

1260

2374

1600

Date:Scale:

Index:Model:

A4

Serial-No.:

Sheet:Paper:1: 02/06

ATX Free Stand Half Rack 240 1

AT

X F

ree Stand H

alf Rack 240

AT

X-F

S-240

01.10.2014ATX-FS-240

List No.: Quantity Item: Sheet

1 2 ATX-UPR-P8-226

2 2 ATX-GR-P8-150

3 4 ATX-TRI-Plate-I

4 1 XCD-106-R3R5

5 1 ATX-XCS-106-P8

6 1 ATX-SB-50 (paar)

7 1 ATX-FH-I (paar)

8 4 ATX-BOLT-20-120

9 12 Screw M14x110mm

10 8 Screw M14x120mm

11 20 Auto-Lock-Nut M14

12 12 Washer M14 3xd

13 28 Washer M14

14 4 ATX-RS-80 Rubber Boot

15 2 Square End-Cap 80x80mm

03/0

6

Mo

de

l:

Sh

ee

t:1:

A4

Pa

pe

r:S

cale

:

Se

ria

l-N

o.:

Da

te:

Ind

ex:

AT

X F

ree

Sta

nd H

alf R

ack

240

ATX Free Stand Half Rack 240

1

ATX-FS-240

AT

X-F

S-2

4001

.10.

2014

4

1

1

632

3

5

3

23

7

7

6

Sheet:

Serial-No.:

Scale: Paper: A4Date:

Model: Index:

1: 04/0601.10.2014

AT

X F

ree Stand H

alf Rack 240

AT

X-F

S-240

ATX-FS-240 1ATX Free Stand Half Rack 240

1

11

13

2

3

13

113

13

10

12

9

Da

te:

Mo

de

l:S

eri

al-

No

.:

A4

Sca

le:

1:

Ind

ex:

Sh

ee

t:05

/06

Pa

pe

r:01

.10.

2014

AT

X-F

S-2

401

ATX Free Stand Half Rack 240ATX-FS-240

AT

X F

ree

Sta

nd H

alf R

ack

240

STEP-1

Alle Teile Exakt ausrichtenund sämtliche Schrauben Festziehen.Beachte die Ausrichtung von Bauteil 1 bezüglichder Skalierung!Align all parts accurately and then tighten all screws.Watch out for the orientation of part 1 with respect tothe scaling!

4 11 13

912

1113

129

5 11 13

912

1113

129

1

1

A4

Ind

ex:

06/0

61:

Sh

ee

t:D

ate

:S

cale

:P

ap

er:

Mo

de

l:S

eri

al-

No

.:

AT

X-F

S-2

401

ATX Free Stand Half Rack 240

AT

X F

ree

Sta

nd H

alf R

ack

240

ATX-FS-240

01.1

0.20

14

STEP-2Alle Teile Exakt ausrichtenund sämtliche Schrauben Festziehen.Beachte wiederrum die Ausrichtung der Skalierung (Bauteil 1)!Align all parts accurately and then tighten all screws.Watch out again for the orientation of the scaling (Part 1)!