28
AUDIO VISUAL TRAINING AUDIO VISUAL TRAINING Vaughn Eames-Lite Class Vaughn Eames-Lite Class
AUDIO VISUAL TRAININGAUDIO VISUAL TRAININGVaughn Eames-Lite ClassVaughn Eames-Lite Class
LITE CLASSROOM EQUIPMENTLite Class
TURNING ON A/V SYSTEM Lite Class
Press the “POWER” button located on the top of the
control panel and the projector will begin turning
on.
PROJECTING A LAPTOPLite Class
Once the projector is on, press the “SOURCE” button until the projector displays
“Input A” on the top right side of the screen.
PROJECTING A LAPTOPLite Class
If you don’t have a “SOURCE” button on your control panel, press the “COMP” button on the control panel to display
your laptop.
PROJECTING A LAPTOPLite Class
Plug in your laptop to the *VGA cord located in the grey
box.
If you have a Mac laptop use your VGA adapter.
*Do not bend or yank on the VGA Cord as this will cause it to break.
PROJECTING A LAPTOPLite Class
If your PC laptop does not project onto the screen, press and hold the “FN” key
located on the bottom left hand side of your laptop’s keyboard.
While holding the “FN” key press the
“F8” key, if you have a Dell laptop.
“ F4” key, if you have an HP laptop.or
“F5” key, if you have a Toshiba/Sony laptop.
Then release them both at the same time.
PROJECTING A LAPTOPLite Class
If your Mac laptop does not display go into your System Preferences and double click “Displays”.
When Display window opens, click “Detect Displays”.
Then click on the “Arrangements” tab.
After Arrangement Tab opens check the box in the bottom left hand corner that says “Mirror Displays”.
PROJECTING A LAPTOPLite Class
To adjust the volume coming from your *computer press the “VOL ” and “VOL ” buttons on the bottom of the control
panel.
*Please note, volume must also be turned up on your laptop to receive sound.
PROJECTING A DVDLite Class
Plug your*borrowed DVD/VCR combo player into an outlet and
press the “POWER” button on the bottom left hand corner of
the player.
*Loaner DVD/VCR players are available for pick up at Audio Visual Technology.
PROJECTING A DVDLite Class
Plug the red, yellow, and white cables (composite cables) into
the back of the DVD player where it says “Line Out”.
PROJECTING A DVDLite Class
Plug the other end of the composite cables into the
corresponding colored jacks on the wall box.
PROJECTING A DVDLite Class
• Press the Eject button next to the DVD player to open it.
• Place DVD in player with label up.
• Push the Eject button again to close and load the DVD player.
PROJECTING A DVDLite Class
Press the “Source” button on the control panel until the
projector shows “VIDEO” in the top right hand corner of the
screen.
If there is no “Source” button press the “Video” button to
display DVD.
PROJECTING A DVDLite Class
There are 2 ways to control your DVD:
1. Use control buttons located on the DVD player itself.
2.Use the remote control that came with the DVD player.
PLAYING A DVDLite Class
To adjust the volume coming from the DVD press the
“VOL +” and “VOL –” buttons on the bottom of the control panel.
PLAYING A DVDLite Class
To stop the DVD press the STOP button located on the bottom left hand corner of the DVD
player.
Press the “Eject” button to retrieve your DVD.
PROJECTING A VHSLite Class
Plug your*borrowed DVD/VCR combo player into an outlet and
press the “POWER” button on the bottom left hand corner of
the player.
*Loaner DVD/VCR players are available for pick up at Audio Visual Technology.
PROJECTING A VHSLite Class
Plug the red, yellow, and white cables (composite cables) into
the back of the VHS player where it says “Line Out”.
PROJECTING A VHSLite Class
Plug the other end of the composite cables into the
corresponding colored jacks on the wall box.
PROJECTING A VHSLite Class
Put your VHS tape into the slot on the right hand side of the
player.
PROJECTING A VHSLite Class
Press the “Source” button on the control panel until the
projector displays “Video” in the top right hand corner of the
screen to have the projector display the VHS tape.
If there is no “Source” button press the “Video” button on the control panel to display the VHS
tape.
PROJECTING A VHSLite Class
There are 2 ways to control your VHS:
1. Use control buttons located on the VHS player itself.
2.Use the remote control that came with the VHS player.
PROJECTING A VHSLite Class
To adjust the volume coming from the VHS press the
“VOL +” and “VOL –” buttons on the control panel.
PROJECTING A VHSLite Class
To stop the VHS, press the STOP button located on the bottom left hand corner of the VCR.
Press the “Eject” button to retrieve your VHS.
TURNING OFF THE A/V SYSTEM Lite Class
To turn off the A/V System press the “Power” button
located on the control panel twice.
TURNING OFF THE A/V SYSTEM Lite Class
Turn off the Laptop or DVD/VCR you are using, disconnect them,
and you have completed shutting down the A/V system.
AUDIO VISUAL CONTACT INFOLite Class
• Office Phone: Ext. 76120
• Office Email: [email protected]
• Office Location: Technology Building Room 110
• Office Website: http://www.kean.edu/~avt/
This presentation was created by Katherine Roba [email protected] ~ 908 737 6122
