13

Spray Coating System SCS4000SCS4000 Spray Coating System is an effi cient machine for applying conformal coatings for various applications. It improves productivity by allowing the selective coating of areas without the need for time consuming masking. Quality of spray is repeatable and coating can be applied especially thin or thick.SCS4000 is a fully programmable selective coating system with an user-friendly proprietary software to perform any intricate patterns that is needed for a good coating process. It also has a programmable tilt and rotate function to access most areas. Together with the gantry system and the spray valve, the system can deliver an even coated area with a maximum of approximately 0.01mm*. Friendly features for area coating allows for fast programming. Dry runs after programming allows user to check position without actual spraying. Valves are easy to service and maintain. There is no expensive replacement part.

Features• Material and substrate dependant• Ease of programming with PC-based Software• Purging stations for material • Low atomising pressure• Strong internal exhaust with overspray chamber for

fume• Low level sensor for material• Material tank with low level sensor• Vision option for Fiducial check and X/Y

programming

Specifi cationsWorking Area 400 x 400x100mmUnder Board Clearance 60mmPCB Edge Clearance 3 – 5mmConveyor Type Chain ConveyorConveyor Adjustment ManualProgramming Method PC Based SoftwareProgram Capacity UnlimitedMotor AC Servo MotorDrive System Ball Screw DriveMaximum Speed 800 mm/secResolution ±2µm per axisRepeatability ±10µm per axisDual Head Dispense/Dot and SprayTilt & Rotate Spray onlyBlack Light (Inspection) 1 x 24 inch LampMaterial Tank 2 x 5 Litre Air Supply 5/6 BarPower 230VAC, 50Hz, 15AmpDimension (W x D x H) 1050 x 1230 x 1735 mmWeight Approx. 600kg

Options• Single Spray Head• Different Work Area• Standalone Desktop Model

Automatic Spray Coating Systems

Technodigm Catalogue.indd 13 7/3/12 10:09 AM

www.techno-digm.com

14

Spray Valve & Controller SV300 & SVC1000SV300 is an air atomizing Spray Valve. It utilized low air pressure to break coating materials into tiny droplets and deposit it onto any coating surfaces. Atomizing pressure can be as low as 8psi. This will ensure that coating material hitting the coating surfaces will not “bounce’ or blown off the intended coating area. The valve comes with an extended nozzle for dipping into solvent to prevent drying out of coating material. Any cleaning or fl ushing is only on the extended nozzle assembly.SVC1000 is a dedicated controller for spray valves. It has a comprehensive range of features for good control of the spraying parameters. It is micro-P driven and can be easily integrated onto any existing system.

Features of Valve• Suitable for low viscosity fast drying conformal

coating• Low atomizing air requirement• Fine adjust of coating material through a micrometer• Compact Design, easy maintenance• Extended nozzle

Features of Controller• User friendly software provides simple setting of all the

necessary parameters• LCD display screen • Microprocessor control• Easily integrated into any coating system• No maintenance needed

Specifi cations of ValveOperating Air Pressure More than 3.0kgf/ cm2

Material Delivery Pressure Max 6.0kgf/ cm2

Maximum Cycle Rate 400 cycles/ min (Full strokes)Weight 360g

Specifi cations of ControllerPower 220VACAir Pressure Range Max 6.0kgf/cm2Spray Pressure 0 - 2 barValve Operating Pressure Max 6 barDispensing Time Range 99.99 secValve, Operating Time 99.99 sec Interval Time 99.99 sec Operating Mode Timer/Auto Mode Manual mode Interval modeWeight Approx. 4.0Kg

Technodigm Catalogue.indd 14 7/3/12 10:09 AM

www.techno-digm.com