Rolling Shutters
automation solutions
E-mail: [email protected] Web: www.toshiautomation.com
RedefinedAutomation
9001:2015Certified
E-mail: [email protected] Web: www.toshiautomation.com
RedefinedAutomation
Types of Rolling Shutter
automation solutions
Manual Rolling Shutter
Gear Type Rolling Shutters are operatedmechanically by using a hand crank /winding handle. Counter balancing of theshutter curtain weight is done by usinghigh tension coil type springs (made fromspecial steel spring wire) within strongsuspension shaft to reduce deflection.The gear operation is through machinecut worm gear. These Rolling Shuttersare ideal for small to medium size.
Automatic Rolling Shutter Toshi Group manufactures a large range of automat ic Ro l l ing Shut te r s fo r a l l commercial and industrial applications. All our Rolling Shutters are automatic using vigorous drive expertise with manual over r ide in case of power fai lure and are dense, noiseless, and dependable with low decibel level. Our rol l ing shuttersconformity with now and demanding building requirements has always been our major objective. All parts of our quality rolling shutter are created in our own unites.
Fire Rated ShutterThe flame roll-up doors are designed for the closure and segmentation of large voids, both in position always open, as in heavy use. Its operation is like any electric roller door, engineized vertical opening, Directgear engine shaft 380 v. frontal displacement without compensation spring, operated by latchkey or button, in case of fire or alarm the control unit sends an electrical signal to the mail box and this means the engine shuts the door. Leaving the door fully closed and the action of fire intumescent expands board installed in the guides and the periphery of the door being fully sealed. In case of lack of electricity, the electric panel issues an order to a 24 VCC auxiliary engine which through a built-UPS * closes the door
E-mail: [email protected] Web: www.toshiautomation.com
RedefinedAutomation
Curtain (Slat Shapes and Sizes)
automation solutions
Slat No Material Drawing Thickness
Guides
FLAT TYPE
Slat No Material Drawing Thickness
BOX TYPE
MS / GI / SS
MS / GI / SS
2.5mm to 3mmW=75mm to 150mm
2.5mm to 3mm
GLC120
GLC77 GALVALUME 0.8mm to 1.2mm
GALVALUME 0.8mm to 1.2mm
0.8mm to 1.2mm
0.8mm to 1.2mm
0.8mm to 1.2mm
0.8mm to 1.2mm
0.8mm to 1.2mm
0.8mm to 1.2mm
0.8mm to 1.2mm
0.8mm to 1.2mm
0.8mm to 1.2mm
0.8mm to 1.2mm
0.8mm to 1.2mm
0.8mm to 1.2mm
0.8mm to 1.2mm
GIC120
GIC77
GIF120
GIF100
MSC77
PERFORATED
PERFORATED
MILD STEEL
GLF100
GI
SSC100 STAINLEES STEEL
MSF100
GLF120
GALVALUME
GALVALUME
GI
GI
GI
MSC120 MILD STEEL
MILD STEEL
MILD STEELMSF120
*and other sizes on required
Drive Systems
Mode of Operation (Motorized)A single phase side motor is used for small to medium sized shutters and a three phase side motor is u s e d f o r l a r g e s h u t t e r s . A d j u s t a b l e l i m i t s w i t c h e s a r e i n c o r p o r a t e d t o s t o p t h e shutter at the end of each travel. All Motors are equipped with a standard control which includes a open-close-stop bottons on a push button switch or a key switch which gives a restricted access operation on the door. Additionally, a Key Switch or a Remote can be provided as an alternate opening solution. A remote & sensing edge can be provided as optional add-ons to the motorized door.
Mumbai Bengaluru Chennai Hyderabad Hongkong Delhi
Plot No. A-1/244, Sector-17 Kavi Nagar Industrial Area,Ghaziabad. Uttar Pradesh Pin Code : 201009
Toshi Automation Solutions
+91-8287116904
[email protected] www.toshiautomation.com
Application
Warehouses Industrial Plants & Factories
Loading Bays Retail Shops Corporate Parks Residential Projects
automation solutions
Indirect Drive
Covers
TOP COVER
Slat No Material Drawing Thickness
MOTOR COVER
.8mm to 1.2mmMS / GI / SS
MS / GI / SS .8mm to 1.2mm
Manual Gear Handle Direct Drive
automation solutions