+ All Categories
Home > Documents > Auxiliary Views

Auxiliary Views

Date post: 08-Mar-2016
Category:
Upload: renzo
View: 224 times
Download: 0 times
Share this document with a friend
Description:
Auxiliary View

of 18

Transcript
  • Auxiliary Views

  • An auxiliary view is an orthographic projection of an angled surface on an object, which appears foreshortened in a typical multiview drawing.Auxiliary views are used to show the true size and shape of an angled surface and its features.Auxiliary Views

  • Foreshortened surfaces on multiview drawings do not give a clear or accurate representation of size or shape and should not be dimensioned.Foreshortened Surfaces

  • Foreshortened SurfacesAn auxiliary view allows the viewer to look perpendicular to an angled surface to witness the true size and shape of that surface and its features (a hole in this example).True HeightAuxiliary Distance

  • There are three types of ordinary auxiliary views: depth auxiliary, height auxiliary, & width auxiliary.Types of Auxiliary Views

  • A depth auxiliary view is derived from a front or back view of an object and will show true depth.A width auxiliary view is derived from a side view of an object and will show true width.A height auxiliary view is derived from the top or bottom view of an object and will show true height.Types of Auxiliary Views

  • Creating Auxiliary ViewsStep #1:Start with a multiview drawing of an object that contains a canted surface. In this case, the canted surface for which the auxiliary view will be created is shown as an angled edge in the front view.

  • Creating Auxiliary ViewsStep #2:Determine which true dimension will be shown by the auxiliary view and identify reference edges on the proper existing view.Draw appropriately spaced construction lines where the auxiliary view will occur. These construction lines will serve as reference lines and must be parallel to the angled edge in question.

  • Reference LineEdge View of Reference Plane

  • Creating Auxiliary ViewsStep #3:Draw construction lines outward from each corner on the view from which the auxiliary view will be a 90 rotation. The lines must be perpendicular to the angled edge in question.Identify the relationship between the corners of the object and the intersections of the construction lines.

  • Creating Auxiliary ViewsStep #4:Draw object lines to connect corners that share a visible edge.

  • This auxiliary view, as projected from the front view, shows the true size and true shape of one of the angled surfaces. If a feature, such as a hole, were located on this surface, it could now be properly dimensioned.

  • Partial ViewsForeshortened object faces may have complex shapes or curves that can be difficult to draw.Short break lines and partial views may be used to remove the need to draw difficult curves on foreshortened faces, while still maintaining complete shape description within a multiview drawing.

  • Partial Views

    Auxiliary ViewsIntroduction to Engineering Design TMUnit 2 Lesson 2.3 Advanced Modeling SkillsAuxiliary ViewsIntroduction to Engineering Design TMUnit 2 Lesson 2.3 Advanced Modeling SkillsAuxiliary ViewsIntroduction to Engineering Design TMUnit 2 Lesson 2.3 Advanced Modeling SkillsAuxiliary ViewsIntroduction to Engineering Design TMUnit 2 Lesson 2.3 Advanced Modeling SkillsAuxiliary ViewsIntroduction to Engineering Design TMUnit 2 Lesson 2.3 Advanced Modeling SkillsAuxiliary ViewsIntroduction to Engineering Design TMUnit 2 Lesson 2.3 Advanced Modeling SkillsAuxiliary ViewsIntroduction to Engineering Design TMUnit 2 Lesson 2.3 Advanced Modeling SkillsAuxiliary ViewsIntroduction to Engineering Design TMUnit 2 Lesson 2.3 Advanced Modeling SkillsAuxiliary ViewsIntroduction to Engineering Design TMUnit 2 Lesson 2.3 Advanced Modeling SkillsAuxiliary ViewsIntroduction to Engineering Design TMUnit 2 Lesson 2.3 Advanced Modeling SkillsAuxiliary ViewsIntroduction to Engineering Design TMUnit 2 Lesson 2.3 Advanced Modeling SkillsAuxiliary ViewsIntroduction to Engineering Design TMUnit 2 Lesson 2.3 Advanced Modeling SkillsAuxiliary ViewsIntroduction to Engineering Design TMUnit 2 Lesson 2.3 Advanced Modeling SkillsAuxiliary ViewsIntroduction to Engineering Design TMUnit 2 Lesson 2.3 Advanced Modeling SkillsAuxiliary ViewsIntroduction to Engineering Design TMUnit 2 Lesson 2.3 Advanced Modeling SkillsAuxiliary ViewsIntroduction to Engineering Design TMUnit 2 Lesson 2.3 Advanced Modeling SkillsAuxiliary ViewsIntroduction to Engineering Design TMUnit 2 Lesson 2.3 Advanced Modeling SkillsAuxiliary ViewsIntroduction to Engineering Design TMUnit 2 Lesson 2.3 Advanced Modeling Skills


Recommended