Aviation Mechanic General. Airframe, and Powerplant...

FAA-G-8082-3

AVIATION MECHANIC GENERAL,

AIRFRAME, AND POWERPLANT

KNOWLEDGE TEST GUIDE

U.S. Department of TransportationFederal Aviation Administration

AVIATION MECHANIC GENERAL,AIRFRAME, AND POWERPLANT


1999

U.S. DEPARTMENT OF TRANSPORTATION

FEDERAL AVIATION ADMINISTRATIONFlight Standards Service

PREFACE

FAA-G-8082-3, Aviation Mechanic General, Airframe, and Powerplant Knowledge Test Guide, provides informationfor obtaining authorization to take the aviation mechanic general, airframe, and powerplant knowledge tests. Appendix1 provides lists of reference materials and subject matter knowledge codes, and a list of computer testing designees(CTD’s).

Changes to the subject matter knowledge codes will be published in AC 60-25, Reference Materials and SubjectMatter Knowledge Codes for Airman Knowledge Testing.

The current Flight Standards Service airman training and testing material, questions banks, and subject matter knowledgecodes for all airman certificates and ratings can be obtained from the Regulatory Support Division, AFS-600, homepage on the Internet.

The Regulatory Support Division’s Internet address is: http://www.mmac.jccbi.gov/afs/afs600

FAA-G-8082-3 supersedes Advisory Circular (AC) 65-28, dated 1995, and can be purchased from the Superintendentof Documents, U.S. Government Printing Office (GPO), Washington, DC 20402-9325, or from U.S. GovernmentBookstores located in major cities throughout the United States. For an explanation of why the Aviation MechanicGeneral, Airframe, and Powerplant Knowledge Test Guide was taken out of the AC system, refer to AC 60-29,Renumbering of Airman Training and Testing Publications.

Occasionally, the word must or similar language is used where the desired action is critical. The use of such languageis not intended to add to, interpret, or relieve a duty imposed by Title 14 of the Code of Federal Regulations (14 CFR).

Comments regarding this guide should be sent to the Federal Aviation Administration, Airman Testing StandardsBranch, AFS-630, Attn: Aviation Mechanic Certification Area Manager, P.O. Box 25082, Oklahoma City, OK 73125.

iii

CONTENTS

Preface ......................................................................................................................................................... iiiContents ........................................................................................................................................................ v

Introduction ................................................................................................................................................... 1Knowledge Test Eligibility Requirements ....................................................................................................... 1Knowledge Areas on the Tests ...................................................................................................................... 2Descriptions of the Tests ............................................................................................................................... 2Process for Taking a Knowledge Test ........................................................................................................... 2Use of Test Aids and Materials ..................................................................................................................... 3Cheating or Other Unauthorized Conduct ...................................................................................................... 4Validity of Airman Test Reports ..................................................................................................................... 4Retesting Procedures .................................................................................................................................... 4

Sample Test Questions and Answers:Aviation Mechanic—General ......................................................................................................................... 5Aviation Mechanic—Airframe....................................................................................................................... 6Aviation Mechanic—Powerplant ................................................................................................................... 7

APPENDIX 1

List of Reference Materials and Subject Matter Knowledge Codes ............................................................ 1-1Aviation Mechanic—General Abbreviations and References ...................................................................... 1-1Aviation Mechanic—General Examination Question References ................................................................ 1-3Aviation Mechanic—Airframe Abbreviations and References .................................................................... 1-7Aviation Mechanic—Airframe Examination Question References ............................................................ 1-10Aviation Mechanic—Powerplant Abbreviations and References ............................................................... 1-16Aviation Mechanic—Powerplant Examination Question References ......................................................... 1-18Computer Testing Designees .................................................................................................................... 1-25

v

INTRODUCTION

What is required to become a skilled and effectiveairframe and powerplant (A & P) aviation mechanic?Although some individuals possess more knowledgeand skills than others, no one is a natural-born aviationmechanic. Competent aviation mechanics become sothrough study, training, and experience.

This knowledge test guide will answer most of yourquestions about taking an aviation mechanic general,airframe, or powerplant knowledge test by coveringthe following areas: knowledge test eligibilityrequirements; knowledge areas on the tests; descriptionsof the tests; process for taking a knowledge test; useof test aids and materials; cheating or otherunauthorized conduct; validity of Airman Test Reports;and retesting procedures.

This guide will help in preparing you to take one or allof the following tests.

Q Aviation Mechanic—General

Q Aviation Mechanic—Airframe

Q Aviation Mechanic—Powerplant

This guide is not offered as an easy way to obtain thenecessary information for passing the knowledge tests.Rather, the intent of this guide is to define and narrowthe field of study to the required knowledge areasincluded in the tests.

KNOWLEDGE TEST ELIGIBILITY

REQUIREMENTS

The general qualifications for an aviation mechaniccertificate require you to have a combination ofexperience, knowledge, and skill. If you are pursuingan aviation mechanic certificate with airframe andpowerplant ratings, you should review the appropriate

sections of Title 14 of the Code of Federal Regulations(14 CFR) part 65 for detailed information pertaining toeligibility requirements. Further information may beobtained from the nearest Flight Standards DistrictOffice (FSDO).

Before taking the certification knowledge and practicaltests, you must meet the eligibility requirements. Thedetermination of eligibility of applicants for the general,airframe, and powerplant tests is made on the basis ofone of the following options:

1. Civil and/or military experience. (See 14CFR part 65, Subpart A—General, and Subpart D—Mechanics.) If you believe you are qualified to exercisethis option, you must have your experience evaluatedand certified by an FAA Aviation Safety Inspector(Airworthiness). If the inspector determines that youhave the required experience, two FAA Forms8610-2, Airman Certificate and/or Rating Application,are completed. These forms are issued, and MUST bepresented along with appropriate identification to takethe corresponding knowledge tests. Your eligibility totest does not expire.

2. Graduation from an FAA-certificatedAviation Maintenance Technician School (AMTS).Depending upon the testing facility affiliation1, agraduation certificate, certificate of completion, or anFAA Form 8610-2, Airman Certificate and/or RatingApplication (properly endorsed) is required, along withproper identification.

If you are taking the tests at a computer testing centerand the practical testing is administered by a designatedmechanic examiner (DME), and BOTH are affiliatedwith the AMTS, a copy of the graduation certificate orcertificate of completion (along with properidentification) may be all that you are required topresent. In this case, the school, the testing center, theDME, and the local FSDO will all be involved and know

AVIATION MECHANIC GENERAL,

AIRFRAME, AND POWERPLANT


1Affiliation is a procedural arrangement to provide for graduates totake the knowledge and practical tests. The arrangement requirementsare agreed to by a particular school, testing center, and designatedmechanic examiner (DME), having also been approved by thesupervising FAA FSDO.

1

what authorization is needed. On the other hand, if eitherone, or both the testing center and the DME are NOTaffiliated with the AMTS, then FAA Form 8610-2 isrequired.

KNOWLEDGE AREAS ON THE TESTS

Aviation mechanic tests are comprehensive becausethey must test your knowledge in many subject areas.The subject areas for the tests are the same as therequired AMTS curriculum subjects listed in 14 CFRpart 147, Appendixes B, C, and D. However, the subjectarea titled “Unducted Fans” (in Appendix D) is not atested subject at this time. The terms used in 14 CFRpart 147, Appendixes B, C, and D are defined in14 CFR part 147, Appendix A.

DESCRIPTIONS OF THE TESTS

All test questions are the objective, multiple-choice type.Each question can be answered by the selection of asingle response. Each test question is independent ofother questions; therefore, a correct response to onedoes not depend upon, or influence, the correct responseto another.

The aviation mechanic general test contains 50questions, and you are allowed 1.5 hours to completethe test.

The aviation mechanic airframe and aviation mechanicpowerplant tests contain 100 questions, and you areallowed 2 hours to complete each test.

Communication between individuals through the useof words is a complicated process. In addition to beingan exercise in the application and use of aeronauticalknowledge, a knowledge test is also an exercise incommunication since it involves the use of the writtenlanguage. Since the tests involve written rather thanspoken words, communication between the test writerand the person being tested may become a difficultmatter if care is not exercised by both parties.Consequently, considerable effort is expended to writeeach question in a clear, precise manner. Make sureyou read the instructions given with the test, as well asthe statements in each test item.

When taking a test, keep the following points in mind:

• Answer each question in accordance with the latestregulations and guidance publications.• Read each question carefully before looking at thepossible answers. You should clearly understand theproblem before attempting to solve it.• After formulating an answer, determine whichchoice corresponds with that answer. The answerchosen should completely resolve the problem.• From the answers given, it may appear that thereis more than one possible answer; however, there isonly one answer that is correct and complete. The otheranswers are either incomplete, erroneous, or representcommon misconceptions.• If a certain question is difficult for you, it is best tomark it for review and proceed to the next question.After you answer the less difficult questions, return tothose which you marked for review and answer them.The review marking procedure will be explained to youprior to starting the test. Although the computer shouldalert you to unanswered questions, make sure everyquestion has an answer recorded. This procedure willenable you to use the available time to maximumadvantage.• When solving a calculation problem, select theanswer closest to your solution. The problem has beenchecked several times by various individuals; therefore,if you have solved it correctly, your answer will becloser to the correct answer than any of the otherchoices.

PROCESS FOR TAKING A KNOWLEDGE

TEST

The Federal Aviation Administration (FAA) hasavailable hundreds of computer testing centersworldwide. These testing centers offer the full rangeof airman knowledge tests including recreationalthrough airline transport pilot, parachute rigger,mechanic, and mechanic examiner tests. Refer toappendix 1 of this guide for a list of computer testingdesignees (CTD’s).

The first step in taking a knowledge test is theregistration process. You may either call the central1-800 numbers (refer to appendix 1 for 1-800 numbers)or simply use the walk-in basis. If you choose to use

2

the 1-800 number to register, you will need to select atesting center, schedule a test date, and make financialarrangements for test payment. You may register fortests several weeks in advance, and you may cancelyour appointment according to the CTD’s cancellationpolicy. If you do not follow the CTD’s cancellationpolicies, you could be subject to a cancellation fee.

The next step in taking a knowledge test is providingproper identification. You should determine whatknowledge test prerequisites are necessary beforegoing to the computer testing center. Your instructor orlocal FSDO can assist you with what documentationto take to the testing facility. Testing center personnelwill not begin the test until your identification is verified.A limited number of tests do not require authorization.

Acceptable forms of authorization are:

• FAA Form 8610-2.• A graduation certificate or certificate of completionto an affiliated testing center as previously explained.• An original (not photocopy) failed Airman TestReport, passing Airman Test Report, or expired AirmanTest Report.

Before you take the actual test, you will have the optionto take a sample test. The actual test is time limited;however, you should have sufficient time to completeand review your test.

Upon completion of the knowledge test, you will receiveyour Airman Test Report, with the testing center’sembossed seal, which reflects your score.

The Airman Test Report lists the subject matterknowledge codes for questions answered incorrectly.The total number of subject matter knowledge codesshown on the Airman Test Report is not necessarily anindication of the total number of questions answeredincorrectly. Appendix 1 contains a list of subject matterknowledge codes that refer to the knowledge areas.Study these knowledge areas to improve yourunderstanding of the subject matter.

The Airman Test Report must be presented to theexaminer prior to taking the practical test. During theoral portion of the practical test, the examiner is requiredto evaluate the noted areas of deficiency.

Should you require a duplicate Airman Test Report dueto loss or destruction of the original, send a signedrequest accompanied by a check or money order for$1 payable to the FAA. Your request should be sent tothe Federal Aviation Administration, AirmenCertification Branch, AFS-760, P.O. Box 25082,Oklahoma City, OK 73125.

USE OF TEST AIDS AND MATERIALS

Airman knowledge tests require applicants to analyzethe relationship between variables needed to solveaviation problems, in addition to testing for accuracy ofa mathematical calculation. The intent is that allapplicants are tested on concepts rather than rotecalculation ability. It is permissible to use certaincalculating devices when taking airman knowledge tests,provided they are used within the following guidelines.The term “calculating devices” is interchangeable withsuch items as calculators, computers, or any similardevices designed for aviation-related activities.

1. Guidelines for use of test aids and materials.The applicant may use test aids and materials withinthe guidelines listed below, if actual test questions oranswers are not revealed.

a. Applicants may use test aids, such as acalculating device that is directly related to the test. Inaddition, applicants may use any test materials providedwith the test.

b. The test proctor may provide a calculatingdevice to applicants and deny them use of their personalcalculating device if the applicant’s device does nothave a screen that indicates all memory has been erased.The test proctor must be able to determine thecalculating device’s erasure capability. The use ofcalculating devices incorporating permanent orcontinuous type memory circuits without erasurecapability are prohibited.

c. The use of magnetic cards, magnetic tapes,modules, computer chips, or any other device uponwhich prewritten programs or information related tothe test can be stored and retrieved are prohibited.Printouts of data will be surrendered at the completionof the test if the calculating device used incorporatesthis design feature.

3

d. The use of any booklet or manualcontaining instructions related to the use of theapplicant’s calculating device is not permitted.

e. Dictionaries are not allowed in the testingarea.

f. The test proctor makes the finaldetermination relating to test materials and personalpossessions that the applicant may take into the testingarea.

2. Guidelines for dyslexic applicant’s use of testaids and materials. A dyslexic applicant may requestapproval from the local Flight Standards District Office(FSDO) to take an airman knowledge test using one ofthe three options listed in preferential order:

a. Option One. Use current testing facilitiesand procedures whenever possible.

b. Option Two. Applicants may use aFranklin Speaking Wordmaster to facilitate the testingprocess. The Wordmaster is a self-containedelectronic thesaurus that audibly pronounces typed inwords and presents them on a display screen. It has abuilt-in headphone jack for private listening. Theheadphone feature will be used during testing to avoiddisturbing others.

c. Option Three. Applicants who do notchoose to use the first or second option may request atest proctor to assist in reading specific words or termsfrom the test questions and supplement material. Inthe interest of preventing compromise of the testingprocess, the test proctor should be someone who isnon-aviation oriented. The test proctor will providereading assistance only, with no explanation of wordsor terms. The Airman Testing Standards Branch,AFS-630, will assist in the selection of a test site andtest proctor.

CHEATING OR OTHER UNAUTHORIZED

CONDUCT

Computer testing centers are required to follow strictsecurity procedures to avoid test compromise. Theseprocedures are established by the FAA and are coveredin FAA Order 8080.6, Conduct of Airman KnowledgeTests. The FAA has directed testing centers toterminate a test at any time a test proctor suspects acheating incident has occurred. An FAA investigationwill then be conducted. If the investigation determinesthat cheating or other unauthorized conduct hasoccurred, then any airman certificate or rating that youhold may be revoked, and you will be prohibited for1 year from applying for or taking any test for acertificate or rating under 14 CFR part 65.

VALIDITY OF AIRMAN TEST REPORTS

Airman Test Reports are valid for the 24-calendarmonth period preceding the month you complete thepractical test. If the Airman Test Report expires beforecompletion of the practical test, you must retake theknowledge test.

RETESTING PROCEDURES

If you receive a grade lower than a 70 percent andwish to retest, you must present the following to testingcenter personnel:

• failed Airman Test Report; or• if you apply within 30 days, a failed Airman TestReport with an endorsement from a mechaniccertificate holder with the same rating(s) you are testingfor, certifying that additional instruction has been given,and that you have been found competent to pass thetest.

If you decide to retake the test in anticipation of a betterscore, you may retake the test after 30 days from thedate your last test was taken. The FAA will not allowyou to retake a passed test before the 30-day periodhas lapsed. Prior to retesting, you must give your currentAirman Test Report to the test proctor. The last testtaken will reflect the official score.

4

1. If the cross sectional area of a given conductoris increased to four times its original value, andthe length and temperature remain constant, theresistance of the conductor will be

A—one-fourth its original value.B—four times its original value.C—found by multiplying the original resistance by the

percentage increase in cross-sectional area.

Answer A—Subject Matter Knowledge Code: A02.AC 65-9A, Airframe & Powerplant MechanicsGeneral Handbook.

One of the factors affecting the resistance of aconductor is cross-sectional area. Resistance variesinversely with the cross-sectional area of aconductor. If the cross-sectional area of a conductoris doubled, the resistance to current flow will bereduced by half (all other factors remainingunchanged).

2. When making a forward weight and balancecheck to determine that the center of gravity (cg)will not exceed the forward limit during extremeconditions, the items of useful load which shouldbe computed at their minimum weights are thoselocated aft of the

A—forward cg limit.B—rearward cg limit.C—empty weight cg.

Answer A—Subject Matter Knowledge Code: C02.AC 65-9A, Airframe & Powerplant MechanicsGeneral Handbook.

When making a forward weight and balance check,part of the information needed is the minimumweights of the items of useful load that are locatedaft of the forward cg limit.

3. What must a certificated mechanic with bothairframe and powerplant ratings do prior toreturning to service an aircraft on which he orshe has performed and approved a 100-hourinspection?

A—Present his/her work and records to a mechanicholding an Inspection Authorization for finalapproval and release.

B—Make the proper entries in the appropriate aircraftmaintenance record.

C—Notify the local FAA FSDO in writing of his/herintention to return the aircraft to service.

Answer B—Subject Matter Knowledge Code: I02.14 CFR section 43.11(a).

The person approving for return to service anaircraft after any inspection shall make an entry inthe maintenance record containing the requiredinformation.

SAMPLE TEST QUESTIONS AND ANSWERS

AVIATION MECHANIC—GENERAL

NOTE: The questions on the aviation mechanic tests pertain to FAA regulations and a wide variety of aircraft,powerplants, and systems. The information contained in the questions must never take precedence over specificinformation furnished by a manufacturer in the maintenance of an aircraft.

5


AVIATION MECHANIC—AIRFRAME

1. Which of the following drill bit types work bestwhen drilling an aramid fiber (Kevlar) compositelaminate?

A—Tool steel with standard grind.B—Diamond dust coated.C—Carbide W-Point.

Answer C—Subject Matter Knowledge Code: D03.AMR, Aircraft Maintenance and Repair.

Standard tool steels dull rapidly when drilling ortrimming composite materials. If diamond-dustcoated drills are used, the fibers will grab at thedrill bit and pull the diamond from the base metalor fill voids in the dust pattern with material. TheW-Point carbide drill design lasts longer and helpssolve fuzz, delamination, and burn problems whendrilling.

2. What is the minimum edge distance allowedfor aluminum alloy single lap sheet splicescontaining a single row of rivets as compared to ajoint with multiple rows, all rivets being equal indiameter?

A—The minimum edge distance for the single row isgreater than that for the multiple row.

B—The minimum edge distance for the single row isless than that for the multiple row.

C—The minimum edge distance for the single row isequal to that for the multiple row.

Answer C—Subject Matter Knowledge Code: D06.AC 43.13-1B, Acceptable Methods, Techniques,and Practices - Aircraft Inspection and Repair.

The minimum edge distance is to be not less thantwo times the diameter of the rivets used for bothsingle and multiple row single lap sheet splices.

3. What is commonly used to connect anemergency source of power, and at the same timedisconnect the normal hydraulic source fromcritical parts of a landing gear or wheel brakingsystem for operation (usually when the normalsource system fails)?

A—Selector valve.B—Shuttle valve.C—Sequence valve.

Answer B—Subject Matter Knowledge Code: K01.AMR, Aircraft Maintenance and Repair.

The function of a shuttle valve is to provide a meansof disconnecting a normal source of hydraulic (orpneumatic) power and connecting an emergencysource of power (hydraulic or pneumatic) to operatethe critical parts of a system.


6


AVIATION MECHANIC—POWERPLANT

1. If an unsupercharged reciprocating engineequipped with a constant speed propeller isoperated at part throttle and at cruising rpm, areduction in rpm with no change in throttle settingwill result in

A—no change in manifold pressure.B—an increase in manifold pressure.C—a decrease in manifold pressure.

Answer B—Subject Matter Knowledge Code: A03.JSPT, A & P Technician Powerplant Textbook.

A reduction in rpm setting (propeller pitch increase)on an unsupercharged reciprocating engineequipped with a constant speed propeller, with nochange in throttle setting, will cause an increase inmanifold pressure. In this case, the decrease in rpmis caused by a higher load being placed on theengine rather than a reduction in fuel flow into theengine.

2. What are the two main sections of a turbineengine for inspection purposes?

A—Hot and cold.B—Combustion and exhaust.C—Compressor and turbine.

Answer A—Subject Matter Knowledge Code: B02.JSPT, A & P Technician Powerplant Textbook.

For inspection purposes, the two main sections ofa turbine engine are hot and cold. The cold sectionincludes the compressor back through the diffuser.The hot section includes the combustor and turbine.

3. Aluminum propeller blade failure at the site ofan unrepaired nick or scratch is usually the resultof

A—material defect.B—intergrannular corrosion.C—stress concentration.

Answer C—Subject Matter Knowledge Code: R07.AP, Aircraft Powerplants.

Even a small defect such as a nick or scratch causesa concentration of stresses that may develop into acrack. The crack in turn results in even greaterstress concentration. The resulting growth of thecrack will almost inevitably result in blade failure.


7

APPENDIX 1

LIST OF REFERENCE MATERIALSAND SUBJECT MATTER KNOWLEDGE CODES

The publications listed in the following pages contain study material you need to be familiar with when preparing foraviation mechanic knowledge tests. All of these publications can be purchased through U.S. Government bookstores,commercial aviation supply houses, or industry organizations. The latest revision of the listed references should berequested. Additional study material is also available through these sources that may be helpful in preparing foraviation mechanic knowledge tests. All publications listed would be excellent for a mechanic to have in a personalreference library.

The following abbreviations are used to identify the reference(s) associated with the subject matter.

AVIATION MECHANIC—GENERAL

ABBREVIATIONS AND REFERENCES

AMT-G Aviation Maintenance Technician SeriesGeneral—Aviation Supplies andAcademics (ASA), Inc.

ABS Aircraft Basic Science—Glencoe Division,Macmillan/McGraw-Hill PublicationCompany

AP Aircraft Powerplants—Glencoe Division,Macmillan/McGraw-Hill PublicationCompany

AEE Aircraft Electricity and Electronics—Glencoe Division, Macmillan/McGraw-HillPublication Company

AC Advisory Circular—Federal AviationAdministration (FAA), GovernmentPrinting Office (GPO)

AIM Aeronautical Information Manual—FAA,GPO

14 CFR Title 14 of the Code of Federal Regulations(part or § [section])—GPO

FAA-G-8082 Guide—FAA, GPOFAA-H-8083 Handbooks—FAA, GPOMBM Marathon Battery Instruction ManualECD Electronic Circuit Devices—Jeppesen

Sanderson, Inc.AB Aircraft Batteries, Lead Acid/Nickel-

Cadmium—Jeppesen Sanderson, Inc.ATD Aircraft Technical Dictionary—Jeppesen

Sanderson, Inc.JSGT A & P Technician General Textbook—

Jeppesen Sanderson, Inc.JSPT A & P Technician Powerplant Textbook—

Jeppesen Sanderson, Inc.

Basic Electricity—AC 65-9A, AMT-G, AEE,MBM, ECD, AB, JSGT

A01 Calculate and measure capacitance andinductance

A02 Calculate and measure electrical powerA03 Measure voltage, current, resistance, and

continuityA04 Determine the relationship of voltage,

current, and resistance in electrical circuitsA05 Read and interpret electrical circuit

diagrams, including solid state devices andlogic functions

A06 Inspect and service batteries

Aircraft Drawings—AC 65-9A, AC 65-15A,ABS, JSGT

B01 Use drawings, symbols, and systemschematics

B02 Draw sketches of repairs and alterationsB03 Use blueprint informationB04 Use graphs and charts

Weight and Balance—AC 65-9A, 14 CFR §23.29

C01 Weigh aircraftC02 Perform complete weight and balance check

and record data

1-1

Appendix 1

Fluid Lines and Fittings—AC 65-9A, ABS,JSGT

D01 Fabricate and install rigid and flexible fluidlines and fittings

Materials and Processes—AC 65-9A, AC 43-3,AC 65-15A, AC 43.13-1B, ABS, AP, ATD,JSPT, JSGT

E01 Identify and select appropriatenondestructive testing methods

E02 Perform dye penetrant, eddy current,ultrasonic, and magnetic particle inspections

E03 Perform basic heat-treating processesE04 Identify and select aircraft hardware and

materialsE05 Inspect and check weldsE06 Perform precision measurements

Ground Operation and Servicing—AC 65-9A,FAA-H-8083-3, AC 65-12A, AIM, ABS, JSGT

F01 Start, ground operate, move, service, andsecure aircraft and identify typical groundoperation hazards

F02 Identify and select fuels

Cleaning and Corrosion Control—AC 65-9A,AC 65-12A, AC 43.13-1B, AC 43-4A, JSGT

G01 Identify and select cleaning materialsG02 Inspect, identify, remove, and treat aircraft

corrosion and perform aircraft cleaning

Mathematics—AC 65-9A, AC 65-12A, ABS,AMT-G, JSGT

H01 Extract roots and raise numbers to a givenpower

H02 Determine areas and volumes of variousgeometrical shapes

H03 Solve ratio, proportion, and percentageproblems

H04 Perform algebraic operations involvingaddition, subtraction, multiplication, anddivision of positive and negative numbers

Maintenance Forms and Records—AC 65-9A,FAA-G-8082-11, AC 43.13-1B, 14 CFR §91.417, 14 CFR part 43

I01 Write descriptions of work performedincluding aircraft discrepancies andcorrective actions using typical aircraftmaintenance records

I02 Complete required maintenance forms,records, and inspection reports

Basic Physics—AC 65-9A, FAA-H-8083-3,ABS, JSGT

J01 Use and understand the principles of simplemachines; sound, fluid, and heat dynamics;basic aerodynamics; aircraft structures; andtheory of flight

Maintenance Publications—AC 65-9A,FAA-G-8082-11, 14 CFR part 21, 14 CFR part39, 14 CFR part 43, ABS, JSGT

K01 Demonstrate ability to read, comprehend,and apply information contained in FAA andmanufacturer’s aircraft maintenancespecifications, data sheets, manuals,publications, and related Federal AviationRegulations, Airworthiness Directives, andAdvisory material

K02 Read technical data

Mechanic Privileges and Limitations—AC43.13-1B, AMT-A, 14 CFR part 43, 14 CFRpart 65

L01 Exercise mechanic privileges within thelimitations prescribed by 14 CFR part 65

1-2

Appendix 1

AVIATION MECHANIC—GENERAL EXAMINATION QUESTION REFERENCESA01:1. AC 65-9A2. AEE3. JSGT4. AC 65-9A5. AC 65-9A6. AEE7. AEE8. AC 65-9A9. AEE10. AC 65-9A11. AEE12. JSGT13. JSGT14. AEEA02:15. AC 65-9A16. AC 65-9A17. AEE18. AC 65-9A19. AC 65-9A20. AC 65-9A21. AC 65-9A22. AC 65-9A23. AC 65-9A24. AC 65-9AA03:25. AC 65-9A26. AC 65-9A27. AC 65-9A28. AC 65-9A29. AC 65-9A30. AC 65-9A31. AEE32. AC 65-9A33. AC 65-9A34. AC 65-9AA04:35. JSGT36. AEE37. AEE38. AEE39. AC 65-9A40. AC 65-9A41. AC 65-9A42. AC 65-9A43. AC 65-9A44. AC 65-9A45. AC 65-9A46. AC 65-9A47. AC 65-9A48. AC 65-9A49. AC 65-9A50. AC 65-9A

51. AC 65-9A52. AC 65-9A53. AC 65-9A54. AC 65-9A55. AC 65-9AA05:56. AEE57. AC 65-9A58. AC 65-9A59. AC 65-9A60. AC 65-9A61. AC 65-9A62. AC 65-9A63. AC 65-9A64. AC 65-9A65. AC 65-9A66. AC 65-9A67. AC 65-9A68. AC 65-9A69. AC 65-9A70. AC 65-9A71. AC 65-9A72. AC 65-9A73. AC 65-9A74. AC 65-9A75. ECD76. ECD77. ECD78. ECD79. ECD80. ECD81. ECD82. AEE83. AEE84. AEEA06:85. AC 65-9A86. JSGT87. AC 65-9A88. JSGT89. JSGT90. AMT-G91. MBM92. AC 65-9A93. AC 65-9A94. JSGT95. JSGT96. AC 65-9A97. MBM98. MBM99. JSGT100. AC 65-9A101. AB102. JSGT

B01:103. ABS104. AC 65-9A105. AC 65-9A106. ABS107. AC 65-9A108. AC 65-9A109. AC 65-9A110. AC 65-9A111. AC 65-9A112. AC 65-9AB02:113. AC 65-9A114. AC 65-9A115. AC 65-9A116. JSGT117. AC 65-9A118. AC 65-9A119. AC 65-9A120. JSGT121. ABS122. AC 65-9AB03:123. AC 65-9A124. AC 65-9A125. AC 65-9A126. AC 65-9A127. AC 65-9A128. AC 65-9A129. AC 65-9A130. AC 65-9A131. ABS132. AC 65-9A133. AC 65-9A134. AC 65-9A135. JSGT136. JSGT137. JSGT138. JSGT139. JSGT140. JSGT141. JSGTB04:142. AC 65-9A143. AC 65-9A144. AC 65-9A145. AEE146. AC 65-9A147. AC 65-9A148. AC 65-9A149. AMR150. AC 65-15A151. AC 65-9A152. AC 65-9A

1-3

Appendix 1

C01:153. AC 65-9A154. AC 65-9A155. AC 65-9A156. ABS157. AC 65-9A158. AC 65-9A159. AC 65-9A160. AC 65-9A161. ABS162. AC 65-9A163. AC 65-9A164. JSGT & ABS165. AC 65-9A166. JSGT167. AC 65-9A168. AC 65-9A169. AC 65-9AC02:170. AC 65-9A171. 14 CFR § 23.29172. AC 65-9A173. JSGT174. AC 65-9A175. AC 65-9A176. 14 CFR § 23.29177. AC 65-9A178. AC 65-9A179. AC 65-9A180. AC 65-9A181. AC 65-9A182. AC 65-9A183. AC 65-9A184. AC 65-9A185. AC 65-9A186. JSGT187. AC 65-9A188. AC 65-9A189. AC 65-9A190. AC 65-9A191. AC 65-9AD01:192. AC 65-9A193. ABS194. AC 65-9A195. ABS196. AC 65-9A197. AC 65-9A198. AC 65-9A199. JSGT200. AC 65-9A201. AC 65-9A202. AC 65-9A203. ABS204. AC 65-9A205. AC 65-9A

206. AC 65-9A207. JSGT208. JSGT209. AC 65-9A210. AC 65-9A211. JSGT212. AC 65-9A213. AC 65-9A214. AC 65-9A215. AC 65-9A216. AC 65-9A217. AC 65-9A218. AMT-GE01:219. AC 65-9A220. JSGT221. AC 43-3222. AC 43-3223. AC 65-9A224. AC 65-9A225. JSGT226. AC 65-9A227. AC 65-15AE02:228. AC 65-9A229. JSGT230. JSGT231. AC 65-9A232. JSGT233. AC 65-9A234. AC 65-9A235. JSGT236. AC 65-9A237. AC 65-9A238. AC 65-9A239. JSGT240. AC 65-9A241. JSGT242. AC 65-9A243. AC 65-9A244. AC 65-9AE03:245. AC 65-9A246. JSGT247. AC 65-9A248. AC 65-9A249. ABS250. ABS251. ABS & JSGT252. AC 65-9A253. ABS254. AC 65-9A255. AC 65-9AE04:256. AMT-G257. AC 65-15A

258. AC 65-9A259. AC 65-9A260. AC 43.13-1B261. JSGT262. AC 43.13-1B263. AC 65-9A264. AC 43.13-1B265. AC 43.13-1B266. AC 43.13-1B267. AC 65-9A268. AMT-G269. AC 65-9A270. AC 65-9A271. AC 65-9A272. AC 43.13-1B273. AC 65-9A274. AC 65-9A275. AC 65-9A276. AC 65-9A277. AC 65-9AE05:278. AC 65-9A279. AC 65-9A280. AMT-G281. AMT-G282. AC 65-15A283. AC 65-15A284. AC 43.13-1B285. AC 65-15A286. AC 65-15A287. AC 65-15A288. AC 65-9AE06:289. ATD & AP290. AC 65-9A291. AC 65-9A292. AC 65-9A293. AC 65-9A294. AC 65-9A295. AC 65-9A296. AC 65-9A297. AC 65-9A298. AC 65-9A299. AC 65-9A300. JSGT301. AP302. AP303. AP304. AP305. AP306. JSPT307. APF01:308. AC 65-9A309. AC 65-9A310. JSGT

1-4

Appendix 1

311. JSGT312. JSGT313. JSGT314. AC 65-9A315. AMT-G316. AC 65-9A317. ABS & JSGT318. AC 65-9A319. JSGT320. JSGT321. AC 65-9A322. AC 65-9A323. AC 65-9A324. AC 65-9A325. AC 65-9A326. ABS327. FAA-H-8083-3328. FAA-H-8083-3329. ABS & AIM330. JSGT331. ABS & AIM332. ABS & AIM333. FAA-H-8083-3334. FAA-H-8083-3 & AIMF02:335. JSGT336. AC 65-9A337. AC 65-9A338. AC 65-9A339. AC 65-9A340. AC 65-9A341. AC 65-9A342. AC 65-9A343. AC 65-9A344. AC 65-9A345. AC 65-9A346. AC 65-9AG01:347. JSGT348. AC 65-12A349. AC 65-9A350. JSGT351. AC 65-9A352. AC 65-9A353. AC 65-9A354. AC 65-9A355. AC 65-9AG02:356. JSGT357. AC 43-4A358. AMT-A359. AC 43-4A360. AC 65-9A361. AC 65-9A362. AC 65-9A363. AC 65-9A

364. AC 65-9A365. AC 43.13-1B366. AC 65-9A367. AC 65-12A368. AC 65-9A369. JSGT & AMT-G370. AC 65-9A371. AC 65-9A372. JSGT & AC 43-4A373. AC 43.13-1B374. JSGT & AC 43-4A375. AC 43-4A376. AC 43-4A377. JSGT378. AC 43-4AH01:379. AC 65-9A380. AC 65-9A381. AMT-G382. AC 65-9A383. AC 65-9A384. ABS385. AC 65-9A386. AC 65-9A387. AC 65-9A388. AC 65-9A389. AC 65-9A390. AC 65-9A391. AC 65-9A392. AC 65-9A393. AC 65-9AH02:394. AC 65-12A395. AC 65-9A396. AC 65-9A397. AC 65-9A398. AC 65-9A399. AC 65-9A400. AC 65-9A401. AC 65-9A402. AC 65-9A403. AC 65-9A404. AC 65-9A405. AC 65-9A406. AC 65-9A407. AC 65-9A408. AC 65-12AH03:409. AC 65-9A410. JSGT411. AC 65-12A412. AC 65-9A413. AC 65-9A414. AC 65-9A415. AMT-G416. AC 65-9A

417. AC 65-9A418. AC 65-9A419. AC 65-9A420. AC 65-9A421. AC 65-9A422. AC 65-9A423. JSGT424. AC 65-9A425. AC 65-9A426. AC 65-9A427. AC 65-9A428. AC 65-9A429. AC 65-9A430. AC 65-9A431. AC 65-9AH04:432. AC 65-9A433. AC 65-9A434. AC 65-9A435. AC 65-9A436. AC 65-9A437. AC 65-9A438. AC 65-9A439. AC 65-9A440. AC 65-9A441. AC 65-9A442. AC 65-9AI01:443. AC 65-9A444. 14 CFR § 43.9445. 14 CFR § 43.11446. AMT-G447. 14 CFR part 43 App A448. FAA-G-8082-11449. 14 CFR part 43450. AC 65-9A451. AC 43.13-1B452. AC 43.13-1B453. AC 43.13-1BI02:454. 14 CFR § 43.11455. 14 CFR § 43.3(b)456. 14 CFR § 43.9457. AC 65-9A458. 14 CFR part 43 App B459. 14 CFR § 91.417460. 14 CFR § 21.197, 91.409461. 14 CFR § 43.15(c)462. 14 CFR part 43463. 14 CFR § 43.9464. 14 CFR § 43.7J01:465. AC 65-9A466. AC 65-9A467. AC 65-9A

1-5

Appendix 1

468. AC 65-9A469. AC 65-9A470. AC 65-9A471. AC 65-9A472. JSGT473. AC 65-9A474. ABS475. AC 65-9A476. AC 65-9A477. AC 65-9A478. AC 65-9A479. AC 65-9A480. AC 65-9A481. AC 65-9A482. JSGT483. AC 65-9A484. AC 65-9A485. AC 65-9A486. ABS487. FAA-H-8083-3488. FAA-H-8083-3489. FAA-H-8083-3490. FAA-H-8083-3491. FAA-H-8083-3K01:492. 14 CFR part 39

493. 14 CFR part 21494. 14 CFR part 39495. AC 65-9A496. JSGT497. 14 CFR § 21.179498. 14 CFR part 21499. 14 CFR part 21500. JSGT501. JSGT502. 14 CFR § 43.11(b)503. JSGT504. 14 CFR § 43.13505. 14 CFR § 23.1543506. 14 CFR § 39.1507. FAA-G-8082-11508. FAA-G-8082-11509. FAA-G-8082-11510. AC 65-9A511. ABS512. ABS513. ABS514. 14 CFR part 43 App AK02:515. 14 CFR part 39516. 14 CFR § 23.1545

517. 14 CFR § 43.13518. 14 CFR § 43.13L01:519. 14 CFR § 65.7 & JSGT520. 14 CFR part 43521. 14 CFR part 43522. 14 CFR part 43 App A523. 14 CFR § 65.7524. 14 CFR § 65.1525. 14 CFR § 65.1526. 14 CFR § 65.1(a)527. 14 CFR part 43 App A528. 14 CFR § 65.1529. 14 CFR § 65.7530. 14 CFR part 65531. 14 CFR § 65.3532. 14 CFR § 65.1533. 14 CFR § 43.13(6)534. AC 43.13-1B535. 14 CFR part 43536. 14 CFR § 65.7537. AMT-A

1-6

Appendix 1

AVIATION—MECHANIC AIRFRAME


AC Advisory CircularAEE Aircraft Electricity and Electronics—

Glencoe Division, Macmillan/McGraw-HillPublication Company

AMR Aircraft Maintenance and Repair—Glencoe Division, Macmillan/McGraw-HillPublishing Company

AP Aircraft Powerplants—Glencoe Division,Macmillan/McGraw-Hill PublishingCompany

AMT-A Aviation Maintenance Technician SeriesAirframe—Aviation Supplies andAcademics (ASA) Publications

DAT Dictionary of Aeronautical Terms—Aviation Supplies and Academics (ASA)Publications

AAC Aircraft Air Conditioning (Vapor Cycle)—Jeppesen Sanderson, Inc.

FMS Aircraft Fuel Metering Systems—Jeppesen Sanderson, Inc.

AHS Aircraft Hydraulic System—JeppesenSanderson, Inc.

AOS Aircraft Oxygen Systems—JeppesenSanderson

JSAT A & P Technician Airframe Textbook—Jeppesen Sanderson, Inc.

JSGT A & P Technician General Textbook—Jeppesen Sanderson, Inc.

ABStruc Aircraft Bonded Structure—JeppesenSanderson, Inc.

WG Welding Guidelines with AircraftSupplement—Jeppesen Sanderson, Inc.

ARS Aircraft Radio Systems—JeppesenSanderson, Inc.

AComp Advanced Composites—JeppesenSanderson, Inc.



MBM Marathon Battery ManualMMM Manufacturer’s Maintenance ManualTSO Technical Standard OrderSUND Sundtrand IDG and BITE 767 Line

Maintenance/Servicing

Wood Structures—AC 65-15A, AC 43.13-1B,AMR

A01 Service and repair wood structuresA02 Identify wood defectsA03 Inspect wood structures

Aircraft Covering—AC 65-15A, AC 43.13-1B,AMR

B01 Select and apply fabric and fiberglasscovering materials

B02 Inspect, test, and repair fabric and fiberglass

Aircraft Finishes—AC 65-15A, AC 43.13-1B,AMR, JSAT

C01 Apply trim, letters, and touchup paintC02 Identify and select aircraft finishing

materialsC03 Apply finishing materialsC04 Inspect finishes and identify defects

Sheet Metal and Non-Metallic Structures—AC 65-9A, AC 65-15A, AC 43.13-1B, 14 CFRpart 23, TSO, AMR, AComp, ABStruc, JSGT,JSAT

D01 Select, install, and remove special fastenersfor metallic, bonded, and compositestructures

D02 Inspect bonded structuresD03 Inspect, test, and repair fiberglass, plastics,

honeycomb, composite, and laminatedprimary and secondary structures

D04 Inspect, check, service, and repair windows,doors, and interior furnishings

D05 Inspect and repair sheet-metal structuresD06 Install conventional rivetsD07 Form, lay out, and bend sheet metal

Welding—AC 65-15A, AC 43.13-1B, AMR,WG, JSAT

E01 Weld magnesium and titaniumE02 Solder stainless steel

1-7

Appendix 1

E03 Fabricate tubular structuresE04 Solder, braze, gas-, and arc-weld steelE05 Weld aluminum and stainless steel

Assembly and Rigging—AC 65-9A, AC 65-15A, AC 61-13B, AC 43.13-1B & 2A, 14 CFRpart 23, AMR, JSAT

F01 Rig rotary-wing aircraftF02 Rig fixed-wing aircraftF03 Check alignment of structuresF04 Assemble aircraft components, including

flight control surfacesF05 Balance, rig, and inspect movable primary

and secondary flight control surfacesF06 Jack aircraft

Airframe Inspection—AC 65-9A, 14 CFR part43, 14 CFR part 65, 14 CFR part 91

G01 Perform airframe conformity andairworthiness inspections

HXX ReservedIXX ReservedJXX Reserved

Aircraft Landing Gear Systems—AC 65-9A,AC 65-15A, AC 43.13-1B, 14 CFR part 43,AMR, AHS, JSAT

K01 Inspect, check, service, and repair landinggear, retraction systems, shock struts,brakes, wheels, tires, and steering systems

Hydraulic and Pneumatic Power Systems—AC 65-9A, AC 65-15A, AMR, AHS, JSAT,AMT-A

L01 Repair hydraulic and pneumatic powersystem components

L02 Identify and select hydraulic fluidsL03 Inspect, check, service, troubleshoot, and

repair hydraulic and pneumatic powersystems

Cabin Atmosphere Control Systems—AC 65-15A, AC 43.13-1B, AMR, AAC, JSAT, 49 CFRpart 173

M01 Inspect, check, service, troubleshoot, andrepair heating, cooling, air-conditioning,pressurization, and air cycle machines

M02 Inspect, check, troubleshoot, service, andrepair oxygen systems

Aircraft Instrument Systems—AC 65-9A, AC65-15A, 14 CFR part 23, 14 CFR part 65, 14CFR part 91, AEE, AMR, AMT-A, JSAT

N01 Inspect, check, service, troubleshoot, andrepair electronic flight instrument systemsand both mechanical and electrical heading,speed, altitude, temperature, pressure, andposition indicating systems to include the useof built-in test equipment

N02 Install instruments and perform a staticpressure system leak test

Communication and Navigation Systems—AC65-15A, AC 91-44A, AC 43.13-2A, AEE, AP,ARS, JSAT

O01 Inspect, check, and troubleshoot autopilot,servos and approach coupling systems

O02 Inspect, check, and service aircraftelectronic communication and navigationsystems, including VHF, passenger addressinterphones and static discharge devices,aircraft VOR, ILS, LORAN, radar beacontransponders, flight management computers,and GPWS

O03 Inspect and repair antenna and electronicequipment installations

Aircraft Fuel Systems—AC 65-9A, AC 65-12A,AC 65-15A, AC 43.13-1B & 2A, 14 CFR part23, 14 CFR part 25, AMR, MMM, FMS,JSGT, JSAT

P01 Check and service fuel dump systemsP02 Perform fuel management, transfer, and

defuelingP03 Inspect, check, and repair pressure fueling

systemsP04 Repair aircraft fuel system componentsP05 Inspect and repair fluid quantity indicating

systemsP06 Troubleshoot, service, and repair fluid

pressure and temperature warning systemsP07 Inspect, check, service, troubleshoot, and

repair aircraft fuel systems

1-8

Appendix 1

Aircraft Electrical Systems—AC 65-9A, AC 65-15A, AC 43.13-1B & 2A, 14 CFR part 23,AEE, MBM, JSGT, JSAT

Q01 Repair and inspect aircraft electrical systemcomponents; crimp and splice wiring tomanufacturer’s specifications; and repairpins and sockets of aircraft connectors

Q02 Install, check, and service airframe electricalwiring, controls, switches, indicators, andprotective devices

Q03 Inspect, check, troubleshoot, service, andrepair alternating and direct currentelectrical systems

Q04 Inspect, check, and troubleshoot constantspeed and integrated speed drive generators

Position and Warning Systems—AC 65-9A, AC65-15A, AC 43.13-1B, 14 CFR part 23, AMR,AMT-A, JSAT

R01 Inspect, check, and service speed andconfiguration warning systems, electricalbrake controls, and antiskid systems

R02 Inspect, check, troubleshoot, and servicelanding gear position indicating and warningsystems

Ice and Rain Control Systems—AC 65-15A,AMT-A

S01 Inspect, check, troubleshoot, service, andrepair airframe ice and rain control systems

Fire Protection Systems—AC 65-9A, AC 65-15A, AP, JSAT

T01 Inspect, check, and service smoke andcarbon monoxide detection systems

T02 Inspect, check, service, troubleshoot, andrepair aircraft fire detection andextinguishing systems

1-9

Appendix 1

A01-A03:1. AMR2. AMT-A3. AC 43.13-1B4. AC 43.13-1B5. AC 43.13-1B6. AC 43.13-1B7. AC 43.13-1B8. AC 65-15A9. AC 43.13-1B10. AC 65-15A11. AC 65-15A12. AC 65-15A13. AMR14. AC 43.13-1BB01-B02:15. AC 43.13-1B16. AC 65-15A17. AC 43.13-1B18. AC 43.13-1B19. AC 65-15A20. AC 65-15A21. AMR22. AMR23. AC 65-15A24. AC 43.13-1B25. AC 43.13-1BC01-C04:26. AMR27. JSAT28. JSAT29. AMR30. JSAT31. AMR32. AC 65-15A33. JSAT34. JSAT35. AC 43.13-1B36. AC 65-15A37. JSAT38. AC 65-15A39. AMR40. AC 65-15AD01:41. AC 65-15A42. JSAT43. AC 65-9A44. AC 65-15A45. AC 65-15A46. JSAT47. AC 65-9A48. AC 65-9A49. AC 65-9A50. JSAT51. AMR52. JSAT53. JSAT

D02:54. AC 65-15A55. AMR56. AMR57. ABStruc58. ABStruc59. JSAT60. AMR61. ABStruc62. ABStruc63. AMR64. AMRD03:65. JSAT66. JSAT67. JSAT68. AC 65-15A69. AC 43.13-1B70. JSAT71. AC 65-15A72. JSAT73. JSAT74. JSAT75. JSAT76. JSAT77. JSAT78. ABStruc79. ABStruc80. AComp81. AC 43.13-1B82. AC 43.13-1B83. AC 43.13-1B84. AComp85. JSAT86. JSAT87. JSAT88. JSAT89. JSATD04:90. AC 65-15A91. AC 43.13-1B92. TSO93. AC 65-15A94. AC 65-15A95. AC 65-15A96. 14 CFR § 23.85397. AC 65-15A98. AC 65-15AD05:99. AC 65-15A100. AC 65-9A & JSGT101. AC 43.13-1B102. AC 65-15A103. AC 65-15A104. AC 65-9A105. AC 65-15A106. AC 65-15A

107. AC 65-15A108. AC 43.13-1B109. AC 65-15A110. AC 65-15A111. JSGT112. AC 65-9A113. AC 65-15A114. AC 65-15A115. AC 65-9A116. AC 43.13-1B117. AMR118. AC 65-9A119. AC 65-15A120. AMR121. AC 65-15A122. AC 65-9A123. AC 65-15A124. AC 65-15A125. AC 65-15A126. AMR127. AC 65-15A128. AC 65-15A129. JSGTD06:130. AC 65-9A131. AC 65-9A132. AC 43.13-1B133. AMR134. AC 65-9A135. AMT-A136. JSGT137. AC 65-9A138. AC 65-9A139. AC 65-9A140. AC 43.13-1B141. AC 65-9A142. AC 65-9A143. AC 43.13-1B144. AC 65-15A145. AC 65-9A146. AC 43.13-1B147. AC 65-9A148. AC 43.13-1B149. AC 65-9A150. AC 65-15A151. AMR152. AC 65-15A153. AC 65-15A154. AC 65-9A155. AC 65-9A156. AC 65-15AD07:157. AC 65-15A158. AC 65-15A159. AC 65-15A160. AC 65-15A161. AC 65-15A

1-10

AVIATION MECHANIC—AIRFRAME EXAMINATION QUESTION REFERENCES

Appendix 1

162. AC 65-15A163. AC 65-15A164. AC 65-15A165. AC 65-15A166. AC 65-15A167. AC 65-15A168. AC 65-15A169. AC 65-15A170. AC 65-9A171. AC 65-15A172. AC 65-15A173. AC 65-15A174. AC 65-15A175. AMR176. AC 65-15A177. AC 65-15A178. AC 65-9AE01-E03:179. JSAT180. AC 65-15A181. AC 65-15A182. AC 65-15A183. AC 65-15A184. AC 65-15A185. AC 43.13-1BE04:186. AC 43.13-1B187. AC 65-15A188. AC 65-15A189. AMR190. AC 65-15A191. AC 65-15A192. AC 43.13-1B & JSAT193. AMR194. AC 65-15A195. AMR196. AC 65-15A197. AC 65-15A198. AC 65-15AE05:199. AC 65-15A200. AC 65-15A201. AC 65-15A202. AC 65-15A203. AC 65-15A204. AC 65-15A205. AC 65-15A206. AC 65-15A207. AC 65-15A208. AC65-9A & JSGT209. AC 65-15A210. AC 65-15A211. AMR & WGF01:212. AC 65-15A213. AC 65-15A214. AC 65-15A215. AC 43.13-2A216. AC 65-15A

217. AC 65-15A218. AC 65-15A219. AC 65-15A220. AC 65-15A221. AC 65-15A222. AC 61-13B223. AC 61-13B224. AC 61-13B225. AC 65-15A226. AC 65-15AF02:227. AC 65-15A228. AMT-A229. JSAT230. AC 65-15A231. AC 65-15A232. AC 65-15A233. AC 65-15A234. AC 65-15A235. AC 65-15A236. AC 65-15A237. AC 65-15A238. AMR239. AC 65-15A240. AC 65-15A241. AC 65-15A242. AC 65-15A243. AC 65-15A244. AC 65-15A245. AC 65-15A246. AC 65-15A247. AC 65-15A248. AC 65-15A249. AC 65-15A250. AC 65-15AF03-F04:251. AC 65-15A252. AC 65-15A253. AC 65-15A254. AC 65-15A255. AC 65-15A256. AC 65-15A257. JSAT258. AC 43.13-1B259. AC 43.13-1B260. AC 43.13-1B261. AC 43.13-1B262. AC 65-9A263. JSGT264. AC 65-15AF05:265. AC 65-15A266. 14 CFR § 23.69(a)(1)267. AC 65-15A268. JSAT269. AC 65-15A270. AC 65-15A271. AC 43.13-1B272. AC 43.13-1B

273. AC 65-15A274. AC 65-15A275. AC 65-9A276. AC 65-15A277. 14 CFR § 23.677(a)278. AC 65-15A279. AC 65-15A280. AC 65-15A281. AC 65-15A282. AC 65-15A283. AC 65-15A284. AMR285. AC 65-15A286. AC 65-15A287. AC 65-9A288. AC 65-15A289. AC 65-15A290. AC 65-15AF06-G01:291. AC 65-9A292. AC 65-9A293. AC 65-9A & 14 CFR part 39294. AC 65-9A295. 14 CFR § 43.7296. 14 CFR part 43297. 14 CFR § 91.409298. 14 CFR § 43.11299. 14 CFR § 91.409

300. 14 CFR § 43.7(b)301. 14 CFR § 91.409302. 14 CFR part 65303. 14 CFR § 91.409304. 14 CFR § 91.409K01:305. AMR & AC 65-9A306. AC 65-15A307. AC 65-15A308. AC 65-15A309. AMR310. AC 65-15A311. AC 43.13-1B312. AC 65-15A313. AC 65-15A & JSAT314. AC 65-15A315. AMT-A316. AC 65-15A317. AC 65-15A318. AMR319. AC 43.13-1B320. AC 65-15A321. AC 65-15A322. AC 65-15A323. AC 65-15A324. JSAT325. AC 65-15A326. AC 65-15A327. AC 65-15A328. AC 65-15A

1-11

Appendix 1

329. AC 65-15A330. 14 CFR § 43.3 & App A331. AC 65-15A332. AC 65-15A333. AC 65-15A334. AMR335. AC 65-15A336. AMR337. AC 65-15A338. AC 65-15A339. AC 65-15A340. AMR341. AC 65-15A342. AC 65-15A343. AC 65-15A344. JSAT345. AMR346. AC 65-15A347. AC 65-15A348. AC 65-15A349. AC 65-15A350. AC-65-15A351. AMT-A352. AC 65-15A353. AMT-A354. AC 65-15A355. AC 65-15A356. AC 65-15A357. AC 65-15A358. AC 65-15A359. AC 65-15A360. JSAT361. AMR362. AC 65-15A363. AC 65-15A364. AC 65-15A365. AC 65-15A366. AC 65-15A367. AC 65-15A368. AC 65-15A369. AMR370. AC 65-15A371. AMR372. AC 65-15A373. AC 65-9A374. AHS375. AC 65-15A376. AC 65-15A377. AHS378. AHS379. AHS380. AHS381. AMR382. JSAT383. AC 65-15A384. AC 65-9A385. AC 65-9AL01:386. AMT-A

387. AC 65-9A388. AC 65-15A389. AC 65-15A390. AC 65-15A391. AC 65-15A392. AC 65-15A393. AC 65-15A394. AC 65-15A395. AC 65-15A396. JSAT397. AC 65-15A398. AC 65-15A399. AC 65-15A400. AC 65-15A401. AC 65-15A402. AC 65-9A403. AC 65-15A404. AC 65-9A405. AC 65-9A406. JSAT407. AHS408. AMR409. AC 65-9A410. JSATL02:411. JSAT412. AC 65-15A413. AC 65-15A414. AC 65-15A415. AC 65-15A416. AC 65-15A417. JSAT418. AC 65-15A419. AC 65-15A420. AC 65-15A421. AC 65-15A422. AC 65-15A423. AC 65-15A424. AC 65-15A425. AC 65-15A426. AC 65-15A427. AHS428. AHS429. AHS430. JSAT431. AC 65-15AL03:432. AC 65-15A433. JSAT434. AMR435. AC 65-15A436. AC 65-15A437. AMR438. AC 65-15A439. AC 65-15A440. AMR441. AC 65-15A442. AC 65-15A443. AC 65-15A

444. AC 65-15A445. AC 65-9A446. AC 65-9A447. AC 65-9A448. AMR449. AC 65-15A450. AC 65-15A451. AC 65-15A452. AC 65-15A453. AC 65-15A454. AMR455. AC 65-15A456. AC 65-15A457. AC 65-15A458. AC 65-15A459. AC 65-15A460. AC 65-15A461. AC 65-15A462. AC 65-15A463. AMR464. AC 65-15A465. AC 65-15A466. AC 65-15A467. AC 65-15A468. AC 65-15A469. AMR470. AC 65-15A471. JSAT472. AC 65-15A473. AC 65-15A474. AMT-A475. AMT-A476. AC 65-15A477. AC 65-15A478. AC 65-15A479. AC 65-15A480. AC 65-15A481. AMT-A482. AC 65-15A483. AMT-A484. AC 65-15A485. AC 65-15A486. AC 65-15A487. AC 65-15A488. AC 65-15A489. AC 65-15A490. AC 65-15A491. AC 65-15A492. AMR493. AHS494. AHS495. AMT-A496. AC 65-15AM01:497. AMT-A498. AC 65-15A499. AC 65-15A500. AC 65-15A501. AMT-A

1-12

Appendix 1

502. AC 65-15A503. JSAT504. AC 65-15A505. AC 65-15A506. AC 65-15A507. AAC508. AAC509. AAC510. AC 65-15A511. AAC512. AMT-A513. AMT-A514. 49 CFR §173.34(e)(15)515. JSAT516. JSAT517. JSAT518. AMR519. AC 65-15A520. AC 65-15A521. AC 65-15A522. AC 65-15A523. AC 65-15A524. AC 65-15A525. AC 65-15A526. AC 65-15A527. AMR528. AMR529. AC 65-15A530. AC 65-15A531. AMT-A532. AC 65-15A533. AC 65-15A534. AC 65-15A535. AC 65-15A536. AC 65-15A537. AMR538. AMR539. AC 65-15A540. AC 65-15A541. AC 65-15A542. AC 65-15A543. AC 65-15A544. DAT545. AC 65-15A546. AMR547. AMT-A548. AMT-A549. AC 65-15A550. AAC551. AAC552. AAC553. JSAT554. AAC555. AAC556. AAC557. AAC558. JSAT559. AAC560. AC 65-15A

561. JSAT562. JSAT563. AMT-AM02:564. AC 65-15A565. AC 65-15A566. AC 65-15A567. AC 65-15A568. AC 65-15A569. AC 65-15A570. AC 65-15A571. AC 65-15A572. AC 65-15A573. AMR574. AC 65-15A575. AC 65-15A576. AC 65-15A577. AC 65-15A578. AC 65-15A579. JSAT580. JSAT581. AC 65-15A582. JSAT & AOS583. JSAT584. AMR585. AC 65-15AN01:586. AC 65-15A587. AC 65-15A588. AC 65-15A589. AMT-A590. AC 65-15A591. AC 65-15A592. 14 CFR § 23.1327593. AC 65-15A594. AC 65-15A595. 14 CFR § 23.1325596. AC 65-15A597. AC 65-9A598. 14 CFR § 65.1599. 14 CFR § 65.1600. AC 65-15A601. DAT602. AC 65-15A603. AMT-A604. AC 65-15A605. AC 65-15A606. AMT-A607. AC 65-15A608. AC 65-15A609. AC 65-15A610. AC 65-15A611. AC 65-15A612. 14 CFR § 91.411613. AC 65-15A614. AEE615. AEE616. AEE

617. JSAT618. AEE619. AEE620. AEE621. AMRN02:622. AMT-A623. AC 65-15A624. AC 65-15A625. AC 65-15A626. 14 CFR § 23.1545627. AC 65-15A628. AMT-A629. AMT-A630. AC 65-15A631. AC 65-15A632. AC 65-15A633. AC 65-15A634. AC 65-15A635. AMT-A636. AC 65-15A637. 14 CFR § 65.81638. AMT-A639. 14 CFR § 65.1(a)640. AC 65-15A641. AC 65-15A642. AMT-A643. AC 65-15A644. JSAT645. JSAT646. JSATO01:647. AC 65-15A648. AC 65-15A649. AC 65-15A650. AC 65-15A651. AEE652. JSAT653. AC 65-15A654. AC 65-15A655. AC 65-15A656. AP657. AEE658. AEE659. JSAT660. AC 65-15AO02:661. AC 65-15A662. AC 43.13-2A663. AC 61-23C664. AC 65-15A665. AC 65-15A666. AC 65-15A667. 14 CFR § 91.207668. AC 65-15A669. JSAT670. AC 91-44A671. 14 CFR § 91.207672. AC 91-44A

1-13

Appendix 1

673. JSAT674. JSAT675. AMT-A676. AEE677. AEE678. AEE679. AEEO03:680. AC 43.13-2A681. AC 65-15A682. AC 65-9A683. AC 65-15A684. AC 43.13-2A685. AC 65-15A686. AC 43.13-2A687. AC 65-15A688. AC 43.13-2A689. AC 43.13-2A690. AC 65-15A691. AC 65-15A692. AC 65-15A693. AC 65-15A694. AC 65-15A695. AC 65-15A696. AC 43.13-2A697. AC 65-15AP01-P03:698. AC 65-9A699. AMR700. 14 CFR § 23.1001701. AC 65-9A702. 14 CFR § 23, 25.1001 & AC

65-9A703. JSAT704. JSAT705. MMM706. AC 65-9A707. AC 65-9A708. AC 65-9A709. AC 65-9A710. AC 65-9A711. AMT-A712. AC 65-9A713. AC 65-9A714. AC 65-9A715. AC 65-9A716. AC 65-9A717. AC 65-9AP04:718. AMT-A719. AC 65-9A720. AC 65-9A721. AMR722. AC 65-9A723. AC 65-9A724. AC 65-9A725. AC 43.13-1B726. AC 65-9A727. AC 65-9A

728. FMS729. AMT-G & AMR730. JSAT731. FMS732. AC 43.13-1B733. AC 43.13-1B734. AC 43.13-1B735. JSGT736. AC 43.13-1BP05:737. AC 65-9A738. AC 65-9A739. AC 65-9A740. AC 65-9A741. AC 65-9A742. AC 65-9A743. AC 65-15A744. AC 65-9A745. AC 65-9A746. AC 65-9A747. JSAT748. AC 65-9A749. AC 65-9A750. AC 65-9A751. AC 65-9A752. AC 65-9A753. AC 65-9A754. AC 65-9A755. JSAT756. 14 CFR § 23.1337P06:757. AC 65-9A758. AMT-A759. AC 65-9A760. AC 65-9A761. AC 65-9A762. AMT-A763. AC 65-9A764. AC 65-9A765. AC 65-9A766. AC 65-9A767. AC 65-9A768. AC 65-9A769. AC 65-12A770. AC 65-12A771. AC 65-12A772. AC 65-9A773. AC 65-9AP07:774. AC 65-9A775. AC 65-9A776. AC 65-9A777. AC 43.13-2A778. AC 65-9A779. 14 CFR § 23.951(b)780. AC 65-9A781. 14 CFR § 25.1557782. AC 65-9A783. AC 65-9A

784. AC 65-9A785. AC 65-9A786. AC 65-9A787. 14 CFR § 23.1557788. AC 65-9A789. AC 65-9A790. AC 65-9A791. AC 65-9A792. AC 43.13-1B793. AC 65-9A794. AMR795. AMT-A796. AC 65-9A797. AC 65-9A798. AC 65-9A799. AMT-G800. AC 65-9A801. JSAT802. AC 65-9AQ01:803. AC 65-9A804. AEE805. AEE806. AC 65-9A807. AC 65-9A808. AC 65-9A809. AC 65-9A810. AC 65-9A811. AC 65-9A812. AC 65-9A813. AC 65-9A814. AC 65-9A815. AC 65-9A816. AC 65-9A817. AC 65-9A818. AC 65-9A819. AC 65-9A820. AEE821. AC 65-15A822. AC 65-9A823. AC 65-9A824. AC 65-9A825. AEE826. 14 CFR § 23.135827. AC 65-9A828. AC 65-9A829. AC 65-9A830. JSGT831. AEE832. JSGT833. JSGT834. JSGT835. JSGT836. MBM837. JSGT838. AC 65-9A839. AC 65-9A840. AC 65-9A841. AC 65-15A

1-14

Appendix 1

842. AC 65-15A843. AC 43.13-1B844. AC 65-15A845. AC 43.13-1B846. AEE847. AEE848. JSAT849. AC 65-9AQ02:850. AC 65-15A851. AC 65-15A852. AC 65-15A853. AC 65-9A854. AC 65-9A855. JSAT856. AC 65-9A857. AC 43.13-1B858. AEE859. AC 43.13-1B860. AC 65-15A861. AEE862. AC 65-9A863. AC 43.13-1B864. AC 43.13-1B865. AC 43.13-1B866. AEE867. AC 65-15A868. AC 65-15A869. AC 65-9A870. AC 65-15A871. AC 43.13-1B872. AC 43.13-1B873. AC 43.13-1B874. AC 43.13-1B875. AC 65-9A876. AC 65-15A877. AC 65-9A878. AEE879. AC 65-15A880. AEE881. AC 43.13-1B882. AEE883. AC 43.13-1B884. AC 65-15A885. AC 43.13-1B886. AC 65-9A887. AC 43.13-1B888. AC 65-15A889. AC 65-9A890. AC 65-15A891. AC 65-9A892. AC 65-9AQ03:893. AC 65-9A894. AEE895. AC 65-9A896. AC 65-9A897. AEE898. AC 65-9A

899. AC 65-9A900. AC 43.13-2A901. AC 65-9A902. AC 65-9A903. AC 65-9A904. AC 65-9A905. AC 65-9A906. AC 65-9A907. AC 43.13-1B908. AC 65-9A909. AEE910. AC 65-9A911. AC 65-9A912. AC 65-9A913. AC 43.13-2A914. AC 65-9A915. AC 65-9A916. AC 65-9A917. AC 65-9A918. AC 65-9A919. AC 65-9A920. AC 65-9A921. AMT-A922. AC 65-9A923. AC 65-9A924. AC 65-9A925. AC 65-9A926. AC 65-15A927. AC 65-9AQ04:928. AEE929. AEE930. AEE931. SUND932. AEE933. JSATR01:934. AC 65-15A935. AC 65-15A936. AC 65-15A937. AC 65-15A938. AMR939. AC 65-15A940. 14 CFR § 23.1323941. AC 65-15A942. JSAT943. AC 65-15A944. AC 65-15A945. AMT-A946. AMT-A947. AC 65-15A948. AMR949. AMR950. AMRR02:951. AC 65-15A952. AC 65-15A953. AC 65-15A954. AC 65-15A

1-15

955. AC 65-15A956. AC 65-15A957. AC 43.13-1B958. AC 65-15A959. AC 65-15A960. AC 65-15A961. AC 65-15A962. AC 65-15A963. AMT-A964. AMT-A965. AMT-A966. AC 65-9A967. AC 65-15A968. AC 65-15AS01:969. AC 65-15A970. AC 65-15A971. AMT-A972. AC 65-15A973. AC 65-15A974. AC 65-15A975. AC 65-15A976. AC 65-15A977. AC 65-15A978. AC 65-15A979. AMT-A980. AC 65-15A981. AC 65-15A982. AC 65-15A983. AC 65-15A984. AC 65-15A985. AC 65-15A986. AC 65-15A987. AC 65-15A988. AC 65-15A989. AC 65-15A990. AC 65-15A991. AC 65-15A992. AC 65-15A993. AC 65-15A994. AC 65-15A995. AC 65-15A996. AC 65-15AT01:997. AC 65-15A998. AC 65-15A999. AC 65-15A1000. AC 65-15A1001. AC 65-15A1002. AC 65-15A1003. AC 65-15A1004. AC 65-15A1005. JSAT1006. AC 65-9A1007. AC 65-15A1008. AC 65-15A1009. AC 65-15AT02:1010. AC 65-15A

Appendix 1

1-16

Appendix 1

1011. AC 65-15A1012. AC 65-15A1013. AC 65-15A1014. AC 65-15A1015. AC 65-15A1016. JSAT1017. AP1018. AC 65-15A1019. AC 65-15A1020. AC 65-15A1021. AC 65-15A1022. AC 65-15A1023. AC 65-15A1024. AC 65-15A1025. AC 65-15A1026. AC 65-15A1027. AC 65-15A1028. AC 65-15A

ABS Aircraft Basic Science—Glencoe Division,Macmillan/McGraw-Hill PublicationCompany

AC Advisory CircularAEE Aircraft Electricity and Electronics—

Glencoe Division, Macmillan/McGraw-HillPublication Company

AMR Aircraft Maintenance and Repair—Glencoe Division, Macmillan/McGraw-HillPublication Company

AMT-G Aviation Maintenance Technician SeriesGeneral—Aviation Supplies & Academics,(ASA) Inc.

AMT-P Aviation Maintenance Technician SeriesPowerplant—Aviation Supplies &Academics, (ASA) Inc.

AP Aircraft Powerplants—Glencoe Division,Macmillan/McGraw-Hill PublicationCompany

DAT Dictionary of Aeronautical Terms—Aviation Supplies & Academics (ASA),Inc.

TCAS Transport Category Aircraft Systems—Jeppesen Sanderson, Inc.

APC Aircraft Propellers and Controls—Jeppesen Sanderson, Inc.

ATD Aircraft Technical Dictionary—JeppesenSanderson, Inc.

JSGT A & P Technician General Textbook—Jeppesen Sanderson, Inc.

JSPT A & P Technician Powerplant Textbook—Jeppesen Sanderson, Inc.

AGTP Aircraft Gas Turbine Powerplants—Jeppesen Sanderson, Inc.


PSG A&P Technician Powerplant Study Guide- Jeppesen Sanderson, Inc.

Reciprocating Engines—AC 65-9A,AC 65-12A, 14 CFR part 43, AP, JSPT, AMT-P

A01 Inspect and repair a radial engineA02 Overhaul reciprocating engineA03 Inspect, check, service, and repair

reciprocating engines and engine installations

A04 Install, troubleshoot, and removereciprocating engines

Turbine Engines—AC 65-9A, AC 65-12A,AC 65-15A, 14 CFR part 33, AP, AGTP, JSPT

B01 Overhaul turbine engineB02 Inspect, check, service, and repair turbine

engines and turbine engine installationsB03 Install, troubleshoot, and remove turbine

engines

Engine Inspection—AC 65-9A, AC 65-12A,AC 39-7B, AC 43.13-1B, 14 CFR part 23,14 CFR part 33, 14 CFR part 43, 14 CFR part65, ABS, AP, JSGT, JSPT

C01 Perform powerplant conformity andairworthiness inspections

DXX ReservedEXX ReservedFXX ReservedGXX Reserved

Engine Instrument Systems—AC 65-12A,AC 65-15A, AC 20-88A, 14 CFR part 65,AMR, AP, AGTP, JSPT, ATD

H01 Troubleshoot, service, and repair electricaland mechanical fluid rate-of-flow indicatingsystems

H02 Inspect, check, service, troubleshoot, andrepair electrical and mechanical enginetemperature, pressure, and RPM indicatingsystems

Engine Fire Protection Systems—AC 65-9A,AC 65-12A, ABS, AMR, AP, JSPT

I01 Inspect, check, service, troubleshoot, andrepair engine fire detection and extinguishingsystems

AVIATION MECHANIC—POWERPLANT


Appendix 1

1-17

Appendix 1

Engine Electrical Systems—AC 65-9A,AC 65-12A, AC 65-15A, AC 43.13-1B,14 CFR part 23, 14 CFR part 25, AEE, AP,JSGT, JSPT

J01 Repair engine electrical system componentsJ02 Install, check, and service engine electrical

wiring, controls, switches, indicators, andprotective devices

Lubrication Systems—AC 65-12A, AC 65-15A,14 CFR part 33, AP, AGTP, JSPT, AMT-P

K01 Identify and select lubricantsK02 Repair engine lubrication system

componentsK03 Inspect, check, service, troubleshoot, and

repair engine lubrication systems

Ignition and Starting Systems—AC 65-12A,AC 65-15A, AEE, AP, AGTP, JSPT

L01 Overhaul magneto and ignition harnessL02 Inspect, service, troubleshoot, and repair

reciprocating and turbine engine ignitionsystems and components

L03 Inspect, service, troubleshoot, and repairturbine engine electrical starting systems

L04 Inspect, service, and troubleshoot turbineengine pneumatic starting systems

Fuel Metering Systems—AC 65-9A,AC 65-12A, AP, AGTP, JSPT

M01 Troubleshoot and adjust turbine engine fuelmetering systems and electronic engine fuelcontrols

M02 Overhaul carburetorM03 Repair engine fuel metering system

componentsM04 Inspect, check, service, troubleshoot, and

repair reciprocating and turbine engine fuelmetering systems

Engine Fuel Systems—AC 65-9A, AC 65-12A,AC 43.13-1B, 14 CFR part 23, AP, JSPT

N01 Repair engine fuel system componentsN02 Inspect, check, service, troubleshoot, and

repair engine fuel systems

Induction and Engine Airflow Systems—AC 65-9A, AC 65-12A, AC 43.13-1B, AP,AGTP, JSPT, AMT-P

O01 Inspect, check, troubleshoot, service, andrepair engine ice and rain control systems

O02 Inspect, check, service, troubleshoot, andrepair heat exchangers, superchargers, andturbine engine airflow and temperaturecontrol systems

O03 Inspect, check, service, and repaircarburetor air intake and induction manifolds

Engine Cooling Systems—AC 65-12A, ABS,AP, JSPT, AMT-P

P01 Repair engine cooling system componentsP02 Inspect, check, troubleshoot, service, and

repair engine cooling systems

Engine Exhaust and Reverser Systems—AC 65-12A, AC 43.13-1B, JSPT

Q01 Repair engine exhaust system componentsQ02 Inspect, check, troubleshoot, service, and

repair engine exhaust systemsQ03 Troubleshoot and repair engine thrust

reverser systems and related components

Propellers—AC 65-9A, AC 65-12A,AC 43.13-1B, 14 CFR part 43, 14 CFR part 65,AP, ATD, APC, JSPT, AMT-P

R01 Inspect, check, service, and repair propellersynchronizing and ice control systems

R02 Identify and select propeller lubricantsR03 Balance propellersR04 Repair propeller control system componentsR05 Inspect, check, service, and repair fixed

pitch, constant speed and featheringpropellers, and propeller governing systems

R06 Install, troubleshoot, and remove propellersR07 Repair aluminum alloy propeller blades

Auxiliary Power Units—DAT, TCAS, ATD,AGTP

T01 Inspect, check, service, and troubleshootturbine-driven auxiliary power units

1-18

1-19

Appendix 1

NOTE: AC 00-2, Advisory Circular Checklist,transmits the status of all FAA advisory circulars(AC’s), as well as FAA internal publications andmiscellaneous flight information such as AeronauticalInformation Manual (AIM), Airport/Facility Directory,knowledge test study guides, and other material directlyrelated to a certificate or rating. AC 00-2 is accessiblethrough the Internet at http://www.faa.gov/abc/ac-chklst/actoc.htm, or you may obtain a free copy from:

U.S. Department of TransportationSubsequent Distribution Office, SVC-121.23Ardmore East Business Center3341 Q. 75 AvenueLandover, MD 20785

A01:1. AC 65-12A2. AMT-P3. AC 65-12A4. AC 65-12A5. AC 65-12A6. AC 65-12A7. AC 65-12A8. AC 65-12A9. AC 65-12A10. AC 65-12AA02:11. AP12. AC 65-12A13. AP14. AMT-P15. AC 65-12A16. AP17. AC 65-12A18. AC 65-12A19. AC 65-12A20. AP21. JSPT22. AC 65-12A23. AP24. AP25. AC 65-12A26. AC 65-12A27. AC 65-12A28. AC 65-12A & AP29. AC 65-12A30. JSPT31. AP32. AC 65-12A33. AMT-P34. AC 65-12A35. AP36. AP37. AP38. AC 65-12A39. AC 65-12A40. AC 65-12A41. AC 65-12A42. JSPT43. AC 65-12A44. AC 65-12A45. AMT-P46. AC 65-12A47. APA03:48. AC 65-12A49. PSG50. AC 65-12A51. AC 65-12A

52. AC 65-12A53. 14 CFR part 4354. JSPT55. AC 65-12A56. AC 65-12A57. AC 65-12A58. AP59. AC 65-12A60. AC 65-12A61. AC 65-12A62. AC 65-12A63. AC 65-12A64. AC 65-12A65. AC 65-12A66. JSPT67. AC 65-9A68. AC 65-12A69. AC 65-12A70. JSPT71. AC 65-12A72. AC 65-12A73. AC 65-12A74. AC 65-12A75. AC 65-12A76. AC 65-12A77. AC 65-12A78. AC 65-12A79. AC 65-12A80. AC 65-12A81. AP82. AC 65-12A83. AP84. APA04:85. AP86. AC 65-12A87. AC 65-12A88. AC 65-12A89. AC 65-12A90. AP91. AC 65-12A92. AC 65-12A93. JSPT94. AC 65-12A95. AC 65-12A96. AC 65-12A97. AC 65-12A98. AC 65-12A99. AP100. AC 65-12A101. AC 65-12A102. AC 65-12A103. AC 65-12A104. AC 65-12A

105. AP106. JSPT107. APB01:108. AC 65-12A109. JSPT110. AC 65-12A111. AC 65-12A112. AP113. AGTP114. AC 65-12A115. AC 65-12A116. AC 65-12A117. AC 65-12A118. JSPT119. AC 65-12A120. AC 65-12A121. AC 65-12A122. AP123. AC 65-9A124. AC 65-12A125. JSPT126. AC 65-12A127. AC 65-12A128. AGTP129. AC 65-12A130. AGTP131. AGTP132. AC 65-12A133. AC 65-12A134. AGTP135. 14 CFR part 33136. AGTP137. AGTP138. JSPT139. 14 CFR § 33.4140. AGTPB02:141. AC 65-12A142. JSPT143. AGTP & AP144. AC 65-12A145. AGTP146. AC 65-12A147. AC 65-12A148. AC 65-12A149. AC 65-12A150. AC 65-15A151. AC 65-12A152. AC 65-12A153. AGTP154. AC 65-12A155. AC 65-12A156. AC 65-12A

1-20

Appendix 1

AVIATION MECHANIC—POWERPLANT EXAMINATION QUESTION REFERENCES

265. AGTP266. APH02:267. AC 65-12A268. AP269. AC 65-15A270. AC 65-15A271. AC 65-15A272. AC 65-12A273. AC 65-12A274. AC 65-15A275. AC 65-12A276. AC 65-12A277. AC 65-12A278. AC 65-15A279. AC 65-15A280. AP281. AC 65-12A282. AC 65-12A283. AC 65-12A284. AC 65-12A285. AC 65-15A286. JSPT & AGTP287. AC 65-12A288. AC 65-15A289. AC 65-15A290. AC 65-12A291. ATD292. AC 65-15A293. AC 65-12A294. AC 65-12A295. AP296. AGTP297. AGTP298. AC 65-12A299. AC 65-12A300. AC 65-12A301. AC 65-12A302. AC 65-12A303. AC 65-12A304. AC 65-12A305. AMR306. AMR307. AGTP308. AP309. AC 20-88AI01:310. AC 65-12A311. AC 65-12A312. AC 65-12A313. AC 65-12A314. JSPT315. AC 65-12A316. AC 65-12A317. AC 65-12A318. AC 65-12A

1-21

Appendix 1

157. AC 65-12A158. AC 65-12A159. AMT-P160. AC 65-12A161. AC 65-12A162. AC 65-12A163. AC 65-9A164. AC 65-9A165. AC 65-12A166. AC 65-12A167. AGTP168. AMT-P169. AC 65-12A170. AC 65-12A171. AC 65-12A172. AC 65-12A173. JSPT174. AGTP175. JSPT176. AP177. AC 65-12A178. AC 65-12A179. AC 65-15A180. AC 65-15A181. AC 65-15A182. AC 65-15A183. AGTP184. AP185. AC 65-12A186. AGTP187. AC 65-12A188. AC 65-12A189. AC 65-12A190. AC 65-12A191. JSPT192. AC 65-12A193. JSPT194. AC 65-12A195. AC 65-12A196. JSPT197. AGTP198. AGTP199. JSPTB03:200. AC 65-12A201. AC 65-9A202. AC 65-12A203. AC 65-12A204. AC 65-12A205. AC 65-12A206. AC 65-12A207. AC 65-12A208. JSPT209. JSPT210. AC 65-12A211. AC 65-12A

212. AC 65-12A213. AC 65-12A214. AC 65-12A215. AC 65-12A216. AC 65-12A217. AGTP218. AC 65-12A219. JSPT220. AGTP221. JSPT222. AC 65-12A223. AGTP224. AGTP225. AP226. AP227. AGTPC01:228. AC 39-7C229. JSGT230. AC 65-12A231. JSPT232. AC 65-9A & AC 39-7C233. AP234. 14 CFR § 39.3 & AC 39-7C235. JSGT236. 14 CFR part 43237. AC 65-12A238. ABS239. AC 43.13-1B240. AC 65-12A241. 14 CFR § 23.903242. AC 65-12A243. AC 65-12A244. AC 65-9A245. 14 CFR § 65.95246. 14 CFR part 43247. 14 CFR part 23248. 14 CFR § 43.13249. 14 CFR § 43.9250. 14 CFR § 43.13a251. AC 65-9A252. 14 CFR part 33 App A253. AC 65-12A254. 14 CFR part 33255. JSPT256. APH01:257. AC 65-12A258. AP259. AP260. AC 65-15A261. AC 65-15A262. AC 65-12A263. AP264. AEE

319. AC 65-15A320. AC 65-12A321. AC 65-12A322. AC 65-12A323. AC 65-15A324. AC 65-12A325. AC 65-12A326. AP327. AC 65-15A328. AC 65-15A329. AC 65-15A330. AC 65-12A331. AC 65-12A332. AC 65-9A333. AC 65-12A334. AC 65-15A335. AC 65-15A336. PSG337. JSPT338. JSPT339. ABS340. JSPT341. AC 65-15AJ01:342. AC 65-9A343. AC 65-9A344. AC 65-9A345. AC 65-12A346. AC 65-9A347. AC 65-9A348. AC 65-9A & AEE349. AC 65-9A350. PSG351. JSPT352. AC 65-9A353. AEE354. 14 CFR § 25.1351355. AC 65-9A356. AC 65-9A357. AC 65-9A358. AC 65-15A359. AEE360. AC 65-9A361. AEE362. JSPT363. AEE364. AEE365. AEE366. AEE367. JSGT368. JSGT369. JSGT370. JSGT371. AP372. JSPT373. JSGT

374. AEEJ02:375. AC 43.13-1B376. AC 65-12A377. AC 43.13-1B378. AC 43.13-1B379. AC 65-12A380. AC 65-12A381. AEE382. AEE383. AC 65-9A384. AC 65-12A385. PSG386. AP387. AC 43.13-1B388. JSPT389. AC 65-12A390. AC 43.13-1B391. AC 43.13-1B392. AC 65-12A393. AC 43.13-1B394. AC 43.13-1B395. JSGT396. JSGT397. 14 CFR part 23398. 14 CFR part 23399. JSPT400. 14 CFR § 23.1357401. JSPT402. JSPT403. AEE404. 14 CFR part 91405. JSPT406. JSPT407. JSPT408. JSPT409. JSPT410. JSPTK01:411. PSG412. JSPT413. AC 65-15A414. AC 65-12A415. JSPT416. JSPT417. AC 65-12A418. JSPT419. PSG420. JSPT421. JSPT422. AP423. AC 65-12A424. AC 65-12A425. JSPT426. AC 65-12A427. AP

428. AP429. AP430. AGTP431. JSPT432. JSPTK02:433. AGTP434. AP435. PSG436. PSG437. JSPT438. AC 65-12A439. AP440. AGTP441. AC 65-12A442. AC 65-12A443. AP444. AC 65-12A445. AC 65-12A446. JSPT447. 14 CFR § 33.71448. 14 CFR § 33.71449. AC 65-12A450. JSPT451. PSG452. AC 65-12A453. AP454. AC 65-12A455. AC 65-12A456. AGTPK03:457. JSPT458. AC 65-12A459. AC 65-12A460. PSG461. PSG462. JSPT463. JSPT464. AP465. JSPT466. PSG467. AC 65-12A468. AC 65-12A469. AMT-P470. PSG471. AC 65-12A472. AP473. AP474. AP475. AC 65-12A476. AC 65-12A477. AC 65-12A478. AGTP479. JSPT480. AC 65-12A481. AP

1-22

Appendix 1

482. AC 65-12A483. JSPT484. JSPT485. JSPT486. JSPT487. JSPT488. AP489. AC 65-12A490. AP491. AGTP492. JSPT493. JSPT494. AC 65-12A495. AC 65-12A496. JSPT497. AC 65-12A498. 14 CFR § 23.1013499. AGTP500. AC 65-12A501. JSPT502. AC 65-12AL01:503. AP504. AC 65-12A505. AC 65-12A506. AC 65-12A507. AC 65-12A508. AP509. AC 65-12A510. AP511. AC 65-12A512. AC 65-12A513. AP514. AC 65-12A515. JSPT516. AC 65-12A517. AC 65-12A518. JSPT519. AC 65-12A520. AC 65-12A521. AC 65-12A522. AC 65-12A523. AC 65-12A524. AC 65-12A525. AC 65-12A526. AC 65-12A527. AC 65-12A528. AC 65-12A529. AC 65-12A530. AP531. AC 65-12A532. AP533. AC 65-12A & AP534. JSPT535. AC 65-12A536. AC 65-12A

537. AC 65-12A538. AC 65-12A539. AP540. APL02:541. JSPT542. AC 65-12A543. AC 65-12A544. AP545. AC 65-12A546. AC 65-12A547. AC 65-12A548. AP549. AC 65-12A550. AC 65-12A551. AC 65-12A552. AC 65-12A553. AP & JSPT554. AEE555. AP556. AC 65-12A557. AC 65-12A558. AC 65-12A559. AGTP560. AGTP561. AP562. JSPT563. JSPT564. JSPT565. AP566. AC 65-12A567. AC 65-12A568. AC 65-12A569. AC 65-12A570. AC 65-12A571. AP572. AP573. AC 65-12A574. AC 65-12A575. AC 65-12A576. AP577. AC 65-12A578. AP579. AC 65-12A580. AC 65-12A581. AC 65-12A582. AC 65-12A583. AC 65-12A584. AC 65-12A585. AC 65-12A586. AC 65-12A587. AC 65-12A588. AC 65-12A589. AC 65-12A590. AC 65-12A591. AC 65-12A

592. AC 65-12A593. AC 65-12A594. AC 65-12A595. JSPT596. AC 65-12A597. AC 65-12A598. AC 65-12A599. AC 65-15A600. AP601. AC 65-12A602. AC 65-12A603. AC 65-12A604. AC 65-12A605. AC 65-12A606. AC 65-12A607. AP608. AC 65-12A609. AC 65-12A610. AC 65-12A611. AC 65-12A612. AC 65-12A613. APL03:614. AC 65-12A615. AC 65-12A616. JSPT617. JSPT618. JSPT619. AC 65-12A620. JSPT621. AC 65-12A622. JSPT623. JSPT624. AC 65-12AL04:625. JSPT626. AGTP627. AP628. JSPT629. JSPT630. AGTP631. JSPT632. AGTP633. AGTPM01:634. AC 65-12A635. JSPT636. AC 65-12A637. AP638. AP639. AP640. AP641. AGTP642. AGTP643. AGTP644. AP

1-23

Appendix 1

1-24

M02:645. JSPT646. AC 65-12A647. AC 65-12A648. AC 65-12A649. AC 65-12A650. AC 65-12A651. JSPT652. AP653. JSPT & AC 65-12A654. AC 65-12A655. AP656. AC 65-12A657. AC 65-12A658. AC 65-12A659. AC 65-12A660. AC 65-12A661. AC 65-12A662. AC 65-12A663. AC 65-12A664. AC 65-12A665. AC 65-12A666. AC 65-12A667. AC 65-12A668. AP669. AP670. AC 65-12A671. JSPT672. AC 65-12A673. AC 65-12A674. AC 65-12A675. AC 65-12A676. AC 65-12A677. AC 65-12A678. AP679. AC 65-12A680. AC 65-12A681. AC 65-12AM03:682. AC 65-12A683. AP684. AC 65-12A685. AC 65-12A686. AC 65-12A687. AC 65-12A688. AP689. AC 65-12A690. AC 65-12A691. AC 65-12A692. AC 65-12A693. AC 65-12A694. AC 65-12A695. AC 65-12A696. AC 65-12A697. AP & JSPT698. AP

M04:699. AC 65-12A700. AC 65-12A701. AC 65-12A702. AC 65-12A703. AP704. AC 65-12A705. AP706. AC 65-12A707. AC 65-12A708. AC 65-12A709. AP710. AC 65-12A711. AC 65-12A712. AC 65-12A713. AC 65-12A714. AC 65-12A715. AC 65-9A716. AC 65-12A717. AC 65-12A718. AC 65-12A719. AC 65-12A720. AC 65-12A721. AC 65-12A722. JSPT723. AC 65-12A724. AC 65-12A725. JSPT726. AGTP727. JSPT728. AC 65-12A729. JSPT730. JSPT731. JSPTN01:732. AC 65-9A733. AC 65-12A734. 14 CFR § 23.995735. AC 65-9A736. AC 65-9A737. AC 65-9A738. AC 65-9A739. AC 65-9A740. AC 65-9A741. AC 65-9A742. AC 65-9A743. APN02:744. AP745. 14 CFR § 23.1189746. AC 65-9A747. AC 43.13-1B748. AC 65-9A749. 14 CFR § 23.955750. AC 65-9A751. AC 65-9A

752. AC 65-9A753. AC 65-9A754. AC 65-12A755. AC 65-9A756. AP757. AP 65-9A758. AC 65-9A759. AC 65-9A760. AP761. AP762. AP763. AC 65-12A764. AC 65-12A765. AP & AC 65-12A766. JSPT767. JSPT768. JSPT769. JSPT770. JSPT771. JSPTO01:772. AP773. AC 65-9A774. AC 65-12A775. AC 65-12A776. AC 65-12A777. AC 65-12A778. AC 65-12A779. AC 65-12AO02:780. AC 65-12A781. AC 65-12A782. AC 65-12A783. JSPT784. AMT-P785. AC 65-12A786. AC 65-12A787. AC 65-12A788. AC 65-12A789. AC 65-12A790. AC 65-12A791. AC 65-12A792. AC 65-12A793. AC 65-12A794. JSPT795. JSPT796. AGTP797. AGTP798. AGTP799. AGTP800. AMT-P801. AGTP802. AGTPO03:803. AP804. AC 65-12A

Appendix 1

1-25

805. AC 65-12A806. AP807. AC 65-12A808. JSPT809. JSPT810. AC 65-9A811. JSPT812. AC 65-12A813. APP01:814. AC 65-12A815. AC 65-12A816. AC 65-12A817. JSPT818. JSPT819. AC 65-12A820. AC 65-12A821. JSPT822. JSPT823. AC 65-12AP02:824. AMT-P825. AC 65-12A826. JSPT827. AC 65-12A828. JSPT829. AC 65-12A830. AC 65-12A831. AP832. AC 65-12A833. AP834. AP835. AC 65-12A836. AC 65-12A837. AC 65-12A838. AC 65-12A839. AP840. ABS841. AP842. AC 65-12A843. AC 65-12A844. AC 65-12A845. AC 65-12AQ01:846. AC 65-12A847. JSPT & AP848. JSPT849. AC 65-12A850. AC 65-12A851. AC 65-12A852. AC 43.13-1B853. AC 43.13-1B854. AGTPQ02:855. AC 65-12A856. AC 65-12A

857. AC 65-12A858. AC 43.13-1B859. JSPT860. AC 65-12A861. JSPT862. AC 65-12A863. AC 65-12A864. AC 65-12A865. AC 65-12A866. AC 65-12A867. AC 43.13-1B868. AC 43.13-1B869. AC 43.13-1B870. AC 43.13-1B871. JSPT872. JSPTQ03:873. AGTP874. AGTP875. AGTP876. AGTP877. AGTP878. AGTP879. AGTP880. AGTPR01:881. AC 65-12A882. AP & AMT-P883. AC 65-12A884. AC 65-12A885. AC 65-12A886. AC 65-12A887. AP888. APC889. JSPTR02-R03:890. AC 65-12A891. AP892. AC 65-12A893. AC 65-12A894. AC 43.13-1B895. JSPT896. AC 65-12A897. AC 65-12A898. JSPTR04:899. AC 65-12A900. AC 65-12A901. AC 65-12A902. AC 65-12A903. AC 65-12A904. AC 65-12A905. AC 65-12A906. AC 65-12A907. AC 65-12A908. AC 65-12A

909. AP910. AC 65-12A911. AC 65-12AR05:912. AC 65-12A913. AC 65-12A914. AC 65-12A915. AC 65-12A916. AC 65-9A917. AC 65-12A918. AC 65-12A919. AP920. AC 65-12A921. AC 65-12A922. AC 65-12A923. AC 65-12A924. AC 65-12A925. AC 65-12A926. AC 65-12A927. AC 65-12A928. AC 65-12A929. AC 65-12A930. AC 65-12A931. AC 65-12A932. AC 65-12A933. AC 65-12A934. JSPT935. AC 65-12A936. AC 65-12A937. JSPT938. AC 65-12A939. AC 65-12A940. AC 65-12A941. AP942. APC943. APC944. AP945. AC 65-12A946. JSPT947. JSPT948. ATD949. AC 65-12A950. AC 65-12A951. AC 65-12A952. AC 65-12A953. AC 65-12A954. AP955. AC 65-12A956. AC 65-12A957. AC 65-12A958. AC 65-12A959. 14 CFR § 65.81, 43 App A,

& JSPT960. AC 65-12A961. AP962. JSPT

Appendix 1

963. JSPT964. JSPT965. JSPTR06:966. JSPT967. AC 65-12A968. AC 65-12A969. AC 65-12A970. AC 65-12A971. APC972. AC 43.13-1B973. AC 65-12A974. AC 65-12A975. AC 65-12A976. APC977. AC 65-12A978. AC 65-12A

1-26

Appendix 1

979. APC980. AC 65-12A981. AC 65-12A982. APR07:983. AC 43.13-1B984. AC 43.13-1B985. AP986. AP987. JSPT988. JSPT989. AP990. AP991. 14 CFR part 43 App A &

14 CFR § 5.81992. ABS993. AMT-G

994. AP995. AP996. 14 CFR part 43 App ATO1:997. TCAS998. TCAS999. TCAS1000. DAT & ATD1001. AGTP1002. TCAS1003. TCAS1004. TCAS1005. AGTP1006. TCAS

COMPUTER TESTING DESIGNEES

The following is a list of the computer testing designees authorized to give FAA airman knowledge tests. This listshould be helpful in case you choose to register for a test or simply want more information.

:: Computer Assisted Testing Service (CATS)

1849 Old Bayshore HighwayBurlingame, CA 94010

Applicant inquiry and test registration: 1-800-947-4228From outside the U.S. (650) 259-8550

:: Sylvan Prometric

1000 Lancaster StreetBaltimore, MD 21202

Applicant inquiry and test registration: 1-800-274-1900, 1-800-967-1100, or 1-800-359-3278From outside the U.S. registrants should contact the appropriate Regional Service Center (RSC):

London, England RSC 44-181-607-9090Paris, France RSC 33-1-4289-3122Dusseldorf, Germany RSC 49-2159-9233-50Tokyo, Japan RSC 813-3269-9620Latin America RSC (612) 820-5200

:: LaserGrade Computer Testing

16209 S.E. McGillivray, Suite LVancouver, WA 98683

Applicant inquiry and test registration: 1-800-211-2753 or 1-800-211-2754From outside the U.S. (360) 896-9111

1-27

Appendix 1

Date post:	24-Aug-2020
Category:	Documents
Upload:	others
View:	30 times
Download:	1 times