Avido™ 10,000mAh Power Bank- Instructional ManualThank you and congratulations on your purchase of the Avido™ 10,000mAh Backup Battery. To get the most of your new product, please read these instructions before use. Enjoy!

Charging the Power Bank

1. Using the Micro-USB Cable, connect the Micro-USB connector into the “IN” input on the Power Bank, and the Standard USB connector to a USB Power Source, such as a laptop computer or smartphone USB charger.

2. The LED screen will indicate the current chargelevel and show progress as the charge progresses.

3. When fully charged, the power bank LED will read“ 100%” charge.

Normal charging time of the Avido™ 10,000mAh Power Bank is approximately 6 hours.

You can check the charge on the Power Bank at anytime by pressing the ON/OFF button on theside of the unit. The LED display will indicate voltage, remaining charge life in %, and charging amps.

KL10000

KL10000

1.0A2.1A

The following illustration is shown with an iPhone 6

Phone CableAC Outlet / Adapter

Micro USB Cable (Included)

Charging the Power BankCharging Your Mobile Devices

Electronic Device

Device Cable

Safety

Improper use of this product may result in product damage, excess heat, toxic fumes, �re or explosions,for which damages you (“Purchaser”), or (“Manufacturer”) are responsible.

• Use only a 5V power adapter for charging,otherwise you may cause damage to thedevice.

Charging the Power Bank (continued)

It is recommended that you charge your AvidoKL1000 Power Bank fully after purchasing the unitand prior to use.

Charging Your Digital Devices

Using the charging cable that was provided with your portable electronic device (i.e., Phone, iPad, Tablet, Portable Speakers, etc.) plug the USB endof the cable into an OUTPUT port on the side of theAvido KL10000 Power Bank. Plug the other end ofthe charging cable into your electronic device. Charging will begin and the LED display will notifyyou of the charge progress.

• OUTPUT 1 is a 1A charging port and suitable for charging phones and smaller portable devices.

• OUTPUT 2 is a 2.1A charging port and should be used for charging iPad’s and Tablet Devices. You can use this output port for charging your phone or other devices as well.

Depending on your device, the Power Bank may automatically shut-o� to conserve power. LED Screen

Press the ON/OFF button which turns on the AvidoKL10000 Power Bank and provides the currentcharge condition.

Press the ON/OFF buttons twice to show the AvidoKL10000 Power Bank charge conditions (voltage,remaining charge life in %, and charging amps.)

If no devices are connected to the Avido KL10000,it will turn o� automatically after about 5 seconds.When the KL10000 is o�, the LED will not beilluminated.

Speci�cations 1. Battery Type: Lithium-Polymer 2. Battery Capacity: 10000mAh 3. Input Power 5.0V, 0.5V/2A 4. USB Output: Output 1 = 5VDC 2.1A & Output 2 = 5VDC 1A 5. Dimensions: 3”W x 5.25” L x 0.5” H 6. Weight: 5oz

Accessories Included• Micro USB Charging Cable• Micro Fiber Carrying Pouch

• The product is not suitable for children as it contains fragile parts that may be swallowed.

• Do not drop or immerse in water as the unit will be damaged.

• Do not expose to high tempartures or �ammable gases.

• Do not remove the housing.

• If there is any damage to the battery such as dents, punctures, tears, deformities or corrosion, due to any cause, discontinue use and contact manufacturer or dispose of it in an appropriate manner at your local battery recycling center.

WarrantyAvido warrants this product to be free from defects in materials and workmanship for 1-Year. If your Avido accessory is found to be defective within that time frame, we will promptly repair or replace it. This warranty does not cover accidental damage, wear and tear, or consequential or incidental loss. If you are in need of warranty support, please emailinfo@avidopower.com.

Customer SupportPlease visit our website www.avidopower.com for additional information and support.

Avido, LLCDesign by Kevin Lance

1-844-MY-AVIDO