B&B Wood Products inc.
Table of Contents PageBarn Door Exterior 29Barn Door Handles 35
Bifold Hardware 22-23Bolts - Flush, Dutch etc 12Bumpers, Door Stops 14ByPass, Pocket, Soft Close 25-26Catches, Hinge Stops 13Clavos 10Closet Rod 42Coat & Hat Hooks 15Decorative Barn Hdwe 31-34Door Closers 21Door Viewers 15Filler Plates & Reinforcers 19Flush Pulls 16-17Gate Hardware 36-37Hand Rail Brackets 15Hinges 3-10Kick Plates 11Letter Plates 20Mult-Fold Hardware 24Pocket Hardware 27-28Pocket Locks 16-17Push & Pull Plates 11Screen & Storm 36-37Shutter - Exterior 38Shutter - Interior 39Strikes 18Wall Mount Slide 30Window Hardware 43Wire Shelving 40-41Closet Rods and Brackets 42
Aluminum Sills, Door Bottoms & Weatherstrip: See Section 10F
Hardware & Shelf Catalog 7-B
September 1, 2020
Handlesets, Passage, Privacy, Keylocks & Multi-Point See Section 8B
See store.bbwood.com for templates and instructions.store.bbwood.com 216-292-6555 [email protected]
Page 23-26Screen & Storm
Page 36-37Page 31-34
Pages 4-5 Page 8 Page 6 Page 10
Page 11 Page 16 Page 40-41
Page 21
Page 18
Page 12-14
Bifold - BipassPage 27-28 Pocket Track
** These finishes are a "living finish" and will change color over time2 7B store.bbwood.com 216-292-6555 [email protected]
ANSI/BHMA/BBW US Equivalent Finish Description Base Material
505 - Bright Brass, Lifetime Finish (PVD)
600 USP Primed for painting Steel
603 US2G Zinc plated Steel
604 US2G Zinc plated and dichromate sealed Steel
605 Bright Brass, clear coated Brass
606 US4 Satin Brass, clear coated Brass
609 US5 Antique Brass (Satin brass, blackened, satin relieved, clear coated) Brass
611 US9 Bright Bronze, clear coated Bronze
612 US10 Satin Bronze, clear coated Bronze
613 US10B Oil Rubbed Bronze (Dark oxidized satin bronze, oil rubbed) ** Bronze
618 US14 Bright nickel plated, clear coated Brass, Bronze
619 US15 Satin Nickel plated, clear coated Brass, Bronze
620 US15A Antique Nickel (satin nickel plated, blackened, satin relieved, clear coated ) Brass, Bronze
622 US19 Flat Black Coated Brass, Bronze
624 US20A Dark oxidized, statuary bronze, clear coated Bronze
625 US26 Bright Chrome plated Brass, Bronze
626 US26D Satin Chrome plated Brass, Bronze
627 US27 Satin aluminum, clear anodized Aluminum Aluminum
628 US28 Satin Aluminum, clear anodized Aluminum
629 US32 Bright stainless steel Stainless steel
630 US32D Satin stainless steel Stainless steel
631 US19 Flat Black Coated Steel
632 US3 Plated bright brass, clear coated Steel
633 US4 Plated satin brass, clear coated Steel
638 US5 Plated satin brass, blackened, satin relieved, clear coated Steel
639 US10 Plated satin bronze, clear coated Steel
640 US10B Oxidized satin bronze plated over copper plate, oil rubbed Steel
645 US14 Bright nickel plated, clear coated Steel
646 US15 Satin nickel plated, clear coated Steel
647 US15A Satin nickel plated, blackened, satin relieved, clear coated Steel
650 US20A Plated dark oxidized statuary bronze, clear coated Steel
651 US26 Bright chromium plated Steel
652 US26D Satin chromium plated Steel
666 US3 Plated bright brass, clear coated Aluminum
667 US4 Plated satin brass, clear coated Aluminum
668 US10 Plated satin bronze, clear coated Aluminum
669 US14 Bright nickel plated Aluminum
670 US15 Satin nickel plated Aluminum
671 US19 Flat Black Coated Aluminum
672 US26 Bright chromium plated Aluminum
673 Aluminum clear coated Aluminum
674 USP Primed for painting Zinc
676 US19 Flat Black Coated Zinc
688 US4 Satin aluminum, gold anodized Aluminum
689 US28 Aluminum painted Any
690 US20 Dark bronze painted Any
691 US10 Light bronze painted Any
693 Black painted Any
695 Dark bronze painted Any
696 US4 Satin brass painted Any
716 Aged Bronze
Finish Key
Hinge TypesOne leaf is MORTISED in the DOOR edge, the other leaf is MORTISED in the JAMB. This is the most common hinge application. Hinges priced on pages 4-5.
One leaf is MORTISED in the DOOR edge, the other leaf is applied to the SURFACE (face) of the JAMB. Used when condi-tions prevent the jamb leaf from being mortised. Call for Quote.
One leaf is applied to the SUR-FACE (face) of the DOOR; the other leaf is applied to the SURFACE (face) of the JAMB. Used when conditions prevent both hinge leaves from being mortised. Call for Quote.
One leaf is applied to the SUR-FACE (face) of the DOOR, the other leaf is MORTISED in the JAMB. Used when conditions prevent the door leaf from being mortised. Call for Quote.
The WIDTH of the hinge is increased (i.e. 4.5" x 6"), moving the barrel away from the face of the door. Used when additional THROW is required to clear trim or wall conditions. Full Mor-tise Only. Priced on pages 4-5.
The hinge leaves locate the bar-rel in a position that allows the door to swing clear of the open-ing when opened to 90 degrees. This permits objects to pass through the opening without hit-ting the hinge edge of the door. Casing may need to notched around barrel. Call for Quote
Solid brass available in most finishes. Available in sizes 3-1/2", 4" and 4-1/2" with square corners. Hinge thickness 0.168"Call for Quote
Both hinge leaves are offset to RAISE the BARREL off the jamb, allowing the door to swing without the knuckles rubbing on the jamb. Used when a door is set deep into a wide frame, prohibiting the use of standard Full Mortise hinges. Full Mortise only. Call for Quote
Raised Barrel
Ornate HingesFull Mortise
Wide Throw
Half Mortise
Half Surface
Full Surface
Swing Clear
UL listed. Adjustable Spring Tension. Full mortise standard priced on page 5. Available in Half Surface - call for quote.
Single Acting Spring
Permits doors to open in either direction and auto-matically return to closed position. Adjustable spring tension. Priced on page 6.
Double Acting Spring
Double acting. Hold open in both directions. Mounts into cut out at bottom of door with top pivot at top corner of door. Priced on page 7.
Floor Hinge
PivotsSpring & Gravity See page 7 for descrip-tions and prices.
other specialty hinge applications available
InvisibleSee page 6 for pric-ing and details.
[email protected] 216-292-6555 store.bbwood.com 7B
Gauge: 3-1/2"=.130, 4"=.130; 4-1/2"=0.134C U/L Listed Grade 1 and BHMA/ANSI A156.17 Grade 1 certified for 1,000,000 cycles
For Double Acting Hinges see pages 6 & 7
LB4310C = Square CornerLB4311C = 1/4" Radius LB4312 C = 5/8" Radius
4 7B store.bbwood.com 216-292-6555 [email protected]
Residential Mortise Hinges
Single Acting Spring Hinges - Steel
3-1/2" hinge pictured
2500 - 9611
Square Corner Steel - Solid Brass
2514 - 9612
1/4" Corner Steel - Solid Brass
2558 - 9613
5/8" Corner Steel - Solid Brass
Ball Steeple
Price per Pair LB4310 Square
LB4311 1/4”R
LB4312 5/8”R
3½” 4” 4½” 3½” 4” 3½” 4”
List Price List PriceList Price List Price List Price List Price List Price
Satin Brass 36.00 40.00 62.00 36.00 40.00 51.00 55.00
Bright Brass 53.00 63.00 86.00 53.00 63.00 55.65 78.00
Antique Brass 59.00 63.00 93.00 59.00 63.00 74.00 78.00
Satin Bronze 60.00 71.00 88.00 60.00 71.00 75.00 86.00
Oil Rub Bronze 51.00 61.00 83.00 51.00 61.00 57.00 76.00
Satin Nickel 46.00 55.00 76.00 46.00 55.00 61.00 70.00
Pewter 59.00 73.00 97.00 59.00 73.00 74.00 88.00
Bright Chrome 61.00 73.00 97.00 61.00 73.00 76.00 88.00
Satin Chrome 46.00 55.00 73.00 46.00 55.00 61.00 70.00
Flat Black 36.00 39.00 62.00 36.00 39.00 51.00 54.00
Thickness: Steel: .085; Solid Brass .096" - .098"
Optional Tips for Solid Brass Hinges:
Extended To use a hinge stop on Solid Brass button tip
hinges you will need to order extended tips.
Price per Pair - Steel Hinges - Plain BearingSteel 2500 Square 2514 1/4”R 2558 5/8”R
Steel 3½” 4” 3½” 4” 3½” 4”
- List Price List Price List Price List Price List Price List Price
Satin Brass 7.00 12.00 5.00 8.00 - -
Bright Brass 10.00 13.00 10.00 13.00 13.00 17.00
Antique Brass 13.00 16.00 13.00 16.00 13.00 17.00
Oil Rub Bronze 11.00 12.00 5.00 12.00 11.00 17.00
Satin Nickel 9.00 11.00 5.00 11.00 9.00 12.00Pewter 13.00 16.00 13.00 16.00 13.00 17.00
Bright Chrome 10.00 13.00 10.00 13.00 13.00 17.00
Satin Chrome 13.00 16.00 13.00 16.00 13.00 17.00
Flat Black 9.00 11.00 9.00 11.00 13.00 17.00
Add Optional Tips (pr) NA NA NA NA NA NA
Price per Pair - Solid Brass Hinges - Plain Bearing
Solid Brass9611 Square 9612 1/4”R 9613 5/8”R
3½” 4” 3½” 4” 3½” 4”Lifetime Polished Brass 44.00 51.00 44.00 51.00 44.00 51.00
Antique Brass 44.00 51.00 44.00 51.00 44.00 51.00
Oil Rub Bronze 44.00 51.00 44.00 51.00 44.00 51.00
Satin Nickel 44.00 51.00 44.00 51.00 44.00 51.00
Pewter 44.00 51.00 44.00 51.00 44.00 51.00
Bright Chrome 44.00 51.00 44.00 51.00 44.00 51.00
Add Optional Tips (pr) 20.00 20.00 20.00 20.00 20.00 20.00
[email protected] 216-292-6555 store.bbwood.com 7B
Heavy Duty Template Mortise Hinges
Size Open Gauge:# screw holes
3-1/2 0.123 64 0.130 84-1/2 0.134 85 0.146 8
Template Steel Hinges Square Corner
Steel 5000 50103½” 4” 4½” 5” 3½”x5 4”x6
Price per Pair List Price
List Price
List Price
List Price List Price
List Price
Satin Brass 15.00 19.00 15.00 49.00 62.00 99.00Bright Brass 27.00 29.00 25.00 63.00 86.00 125.00Antique Brass 27.00 29.00 30.00 63.00 97.00 140.00
Satin Bronze 20.00 24.00 19.00 52.00 80.00 124.00
Oil Rub Brz (US10B) 27.00 29.00 25.00 63.00 97.00 140.00
Brz Black’d (US10A) 30.00 24.00Satin Nickel 23.00 25.00 22.00 54.00 75.00 125.00
Pewter 27.00 29.00 30.00 63.00 97.00 140.00
Bright Chrome 27.00 29.00 25.00 63.00 86.00 140.00Satin Chrome 25.00 26.00 20.00 56.00 75.00 140.00Flat Black 25.00 28.00 30.00Add Ball/Steeple (pr) 31.00 31.00 31.00 31.00 31.00 31.00Add NRP (pr) 13.00 13.00 13.00 13.00 13.00 13.00
Solid Brass 962 Plain Bearing SquarePrice per Pair 3½” 4” 4½” 5” - -
Bright Brass 53.00 61.00 69.00 54.00 - -
Antique Brass 53.00 61.00 69.00 - -
Oil Rub Bronze 53.00 61.00 69.00 54.00 - -
Satin Nickel 53.00 61.00 69.00 - -
Pewter 53.00 61.00 69.00 - -
Bright Chrome 53.00 61.00 69.00 54.00 - -
Add Ball/Steeple (pr) 22.00 22.00 22.00 22.00 - -Add NRP (pr) 13.00 13.00 13.00 13.00 - -
Wide Throw HingeWide Throw – Width of hinge is increased, moving barrel away from the door. Used when required to clear thick casing.
5000, BB5000 962, BB964
(Steel)
(Solid Brass)5010, BB5010 (Steel)
Modern Square Barrel 965 Template HingesFinishes: Polished Brass-Lifetime, Satin Brass, French Antique, Oil Rub Bronze, Polished Nickel, Satin Nickel, Pewter, Flat Black, Polished Chrome.
3-1/2"
Bold Pricing Stock. Store.bbwood.com for stock status
Priced on-line store.bbwood.com
Ball Bearing Hinges Square CornerBB5000 BB5010
3½” 4” 4½” 5” 3½”x5 4”x6List
PriceList
PriceList
PriceList
Price List Price List Price
41.00 46.00 32.00 60.00 90.00 128.0057.00 62.00 39.00 76.00 116.00 154.0057.00 62.00 52.00 130.00 99.00
56.00 61.00 39.00 70.00 115.00 159.00
57.00 62.00 40.00 76.00 130.00 172.00
57.00 62.00 40.00
51.00 53.00 30.00 58.00 103.00 141.00
57.00 62.00 40.00 76.00 130.00 172.00
57.00 62.00 40.00 76.00 116.00 154.0054.00 57.00 34.00 63.00 103.00 141.0036.00 39.00 84.00 83.0031.00 31.00 31.00 31.00 31.00 31.0013.00 13.00 13.00 13.00 13.00 13.00
BB964 Ball Bearing3½” 4” 4½” 5” - -
65.00 74.00 84.00 89.00 - -
65.00 74.00 84.00 89.00 - -
65.00 74.00 84.00 89.00 - -
65.00 74.00 84.00 89.00 - -
65.00 74.00 84.00 89.00 - -
65.00 74.00 84.00 89.00 - -
22.00 22.00 22.00 22.00 - -
13.00 13.00 13.00 13.00 - -
4"
6 7B store.bbwood.com 216-292-6555 [email protected]
DOOR SIZES & WEIGHTS
#3029 - Door flange mortised in door. - Jamb flange surface applied to face of frame. - Recommend 1-1/2 pair hinges per door. Center hinge should be installed as close as possible to top hinge for support. - Do not use on doors with hinge edge beveled.#1515 - Door flange surface applied or mortised. - Jamb flange surface applied.Hinges are Non-Handed.
1515 1515H - (Hold Open)1514 (1514H)
Item 2 Hinges per Door 3 Hinges per Door
NumberMaximum
Door WeightMaximum
Door WidthMaximum
Door WeightMaximum
Door Width Door ThicknessMinimum
Door Height1514 (1514H) 18 1'6" -- -- 7/8" to 1" 3'6"1515 (1515H) 18 1’6" -- -- 1-1/16" to 1-1/2" 3’6"3029-3 35 2’0" 39 2’8" 3/4" to 1" 5’0"3029-4 60 2’4" 75 3’0" 7/8" to 1-1/4" 6’8"3029-5 65 2’8" 93 3’0" 1-1/8" to 1-1/2" 6’8"3029-6 75 2’8" 107 3’0" 1-1/4" to 1-3/4" 7’0"3029-7 82 3’0" 120 3’6" 1-3/8" to 2" 7’0"3029-8 103 3’6" 143 4’0" 1-1/2" to 2" 7’0"3029-5x3.5* 65 2’8" 93 3’0" 1-3/8" 6’8"3029-6x4.5* 75 2’8" 107 3’0" 1-3/4" 7’0"3029-8x4.5* 103 3’6" 143 4’0" 1-3/4" 7’0"
DOUBLE ACTING SPRING HINGES
B&B Wood Products inc.
*Hinges will fit into standard full mortise hinge cutout in metal door; but if standard hinge locations are furnished on 1-3/4" hollow metal doors, we recommend using 3029-8x4.5 hinges for maximum support. Contact our office for pricing.
3029
Louver Door Hinge
1514 & 1514H are priced on our store website and BBQuote
For 3029-5x3.5, 3029-6x4.5 or 3029-8x4.5 call for pricing
Price per Pair 1515 1515H 3029-3 3029-4 3029-5 3029-6 3029-7 3029-8
List Price List Price List Price List Price List Price List Price List Price List Price
Satin Brass 81.00 110.00 121.00 128.00 176.00 195.00 241.00 354.00
Bright Brass 90.00 124.00 136.00 144.00 201.00 218.00 270.00 397.00
Antique Brass - - 180.00 190.00 262.00 289.00 357.00 526.00
Satin Bronze 81.00 110.00 121.00 128.00 176.00 195.00 241.00 354.00Oil Rub Bronze - - 180.00 190.00 262.00 280.00 357.00 526.00
Satin Nickel - - 160.00 169.00 233.00 257.00 318.00 468.00
Pewter 180.00 190.00 262.00 289.00 357.00 526.00
Zinc Plated 84.00 113.00 125.00 132.00 182.00 201.00 249.00 366.00
Satin Chrome - - 155.00 163.00 226.00 249.00 308.00 454.00Flat Black 67.00 92.00 100.00 106.00 146.00 161.00 199.00 293.00
Bold Pricing Stock. Store.bbwood.com for stock status
[email protected] 216-292-6555 store.bbwood.com 7B
7811/7813HD Ball Bearing Floor MountsFor 1-3/8" to 1-3/4" Doors
DOUBLE ACTING FLOOR HINGES
B&B Wood Products inc.
•STEEL MECHANISM•DOUBLE ACTING•ANTI FRICTION BEARING•ADJUSTABLE SPRING TENSION•HOLD OPEN AT APPROXIMATELY 85 DEGREES•NON-HANDED•MAXIMUM DOOR WIDTH 3'0"•WEIGHTS UP TO 90 LBS (*7813HD for 150lbs)
Jamb brackets (7805) may be purchased as a separate item to allow conversion of any pivot from the standard floor mount to jamb mounted.
(included in 7811)
- 7811 7813HD 7805
List Price List Price List Price
Satin Brass 103.00 179.00 13.00Bright Brass 126.00 216.00 16.00Antique Brass 130.00 253.00 20.00
Satin Bronze 110.00 184.00 13.00
Oil Rub Bronze 149.00 238.00 20.00Satin Nickel 135.00 215.00 17.00
Pewter 154.00 253.00 20.00Bright Chrome 149.00 253.00 16.00Satin Chrome 135.00 215.00 17.00Flat Black 109.00 164.00 22.00
ANSI K82193
HEAVY DUTY 7813HD : No Hold Open Feature*7813HD hinge can be used for doors weighing minimum of 90 lbs. up to 150 lbs. Do not use this hinge if doors are less than 90 lbs.
GRAVITY PIVOTS
Hold Open at 90 Degrees• Steel• Double Acting• Door weight closes door - No Springs• Non-Handed• Maximum Door Size & Weight Width - 30” max Weight - 50 lbs. max• Flat Door Bracket - Doors 7/8” TO 1 5/8” thick• Flat Jamb Bracket - 1 1/4” WIDE Notes: Round the jamb edge of door 7/8" radius. Top clearance required 3/4" (5/8" lift). Pivot side of door to jamb requires 5/32". Made in USA.
Gravity Pivots 7512H 173
Finish List Price List Price
Satin Brass 72.00 22.00Bright Brass 72.00 -Antique Brass 89.00 -
Satin Bronze 89.00 -
Oil Rub Bronze 93.00 -Satin Nickel 82.00 -Pewter 112.00 -
Zinc Plated 112.00 -
Satin Chrome 82.00 -Flat Black 72.00 -
JAMB MOUNT:
7512-H 7512-H Price is for 1 pivot only, if ordering for a pair of cafe doors Order 2 sets.
173 SWING & STAY: Max Weight 50lbsIncludes pivots for 2 panels (one pair) of cafe doors.Clearance needed between jamb and panel: Panel thickness Side Jamb Clearance 3/4" 1/4" 1-1/8" 3/8" 1-3/8" 1/2"
Bold Pricing Stock. Store.bbwood.com for stock status
173 Price is for 2 pivots, one pair of cafe doors. Order 1 set.
A 1/2” 1/2” 5/8” 3/4” 1” 1-1/8” 1-3/8”B - - 29/64” 17/32” 23-32” 7/8” 1-1/16”C 1-3/4” 2-3/8” 2-3/4” 3-3/4” 4-5/8” 4-5/8” 5-1/2”D 23/64” 23/64” 9/64” 5/32” 7/32” 3/8” 1/2”E - - 5/32” 3/16” 1/4” 1/4” 9/32”F - - 1-11/32” 2-1/16” 2-19/32” 2-7/16” 2-15/16”G 1/32” 1/16” 3/64” 3/64” 1-16” 3/64” 1/16”H 23/32” 23/32” 29/32” 1-5/64” 1-7/16” 1-19/32” 1-15/16”I - - 9/32” 3/8” 15/32” 13/32” 15/32”
Min Wood Thick 3/4” 3/4” 1” 1-1/8” 1-3/8” 1-3/4” 2”
HINGE 203 204 208 212 216 218 220FINISH List Price List Price List Price List Price List Price List Price List Price
Satin Brass 34.00 35.00 44.00 80.00 126.00 134.00 212.00Bright Brass 65.00 74.00 90.00 142.00 212.00 254.00 322.00Ant Brass 76.00 85.00 128.00 186.00 250.00 276.00 356.00
Oil Rub Brz 76.00 85.00 128.00 170.00 226.00 276.00 356.00
Satin Nickel 44.00 49.00 60.00 90.00 148.00 176.00 284.00
Bright Chrome 65.00 74.00 100.00 142.00 212.00 254.00 322.00Satin Chrome 38.00 39.00 48.00 80.00 126.00 134.00 212.00Black 40.00 43.00 56.00 92.00 150.00 158.00 240.00
8 7B [email protected] p: 216-292-6555
SOSS INVISIBLE HINGES
Minimum Door Thickness
CHOOSING THE RIGHT SOSS HINGE
DIRECTIONS: After determining the weight and width of the door, locate the value of the two scales and connect with a straight line that continues to line”A”.
Draw a line perpendicular to the rules in the table until you reach the proper wood thickness. Use the number and size indicated on this line
RECOMMENDED SPACINGThe “center” hinge should be located ½ the distance from the horizontal centerline of the door to the centerline of the top hinge.On installations requiring 4 hinges, the second hinge from the top should be located ½ the distance from the door’s horizontal center line to the center line of the top hinge. The third hinge from the top should be located ¼ of the ”B” dimension below the horizontal centerline of the door.
The SOSS® Invisible Closer gives you a closer that is totally invisible from either side when the door is closed. The closure rate is completely adjustable with an allen wrench after installation, and does not require removal of the close. The closure rate is adjustable with an allen wrench after installation, and does not require removal of the closer. Installation can be either inside the door or inside the door jamb.
9f: 216-292-6584 p:216-292-6555 [email protected] 7B
PATH AND CLEARANCE FOR SOSS INVISIBLE HINGES
The diagram shows the typical path of a SOSS hinged door. The table shows the door clearance when fully opened for each SOSS hinge.
SOSS Invisible Spring Closer Hinge
SOSS FIRE 20-Minute Invisible Hinges
Door Thickness
Closer # Description A B C D
1-1/8" 212IC One closer for every 28 lbs. of door weight or portion thereof.
1-5/16" 3/8" 5-11/32" 1/2"
1-3/8" 216IC One closer for every 55 lbs. of door weight or portion thereof.
17/16" 3/8" 6-1/4” 3/4”
1-3/4" 218IC One closer for every 55 lbs. of door weight or portion thereof.
141/64" 3/8" 7" 1"
2" 220IC One closer for every 55 lbs. of door weight or portion thereof.
115/16" 3/8" 7" 1"
SOSS® Invisible Hinge models #216FR, #218FR , #220FRis for use in wood or metal applications. Made of zinc and steel mate-rials. Nylon links provide added strength and durability. SOSS® Invisible Hinges open a full 180° and are a single action hinge.These hinges are priced the same as the non-rated hinges on page8.The Underwriters Laboratories labeled these hinges for use on hollow metal , sheet metal, tin clad, steel composite or wood core swinging type fire doors and frames with a 20 minute rating. Pricing is the same as the non-rated hinge.
- 212IC 216IC 218IC 220IC- List Price List Price List Price List Price
Satin Brass 187.00 212.00 231.00 278.00
Bright Brass 221.00 270.00 273.00 327.00
Oil Rub Bronze 231.00 275.00 286.00 331.00
Satin Nickel 204.00 244.00 250.00 305.00
Bright Chrome 221.00 270.00 273.00 327.00
Satin Chrome 187.00 212.00 231.00 278.00
Black 194.00 228.00 237.00 283.00The number of hinges needed can be calculated using the hinge calculator found on our website. Recommended spacing for use of one spring closer is half of the distance from the center line of the door to the center line of the top hinge. Please reference recommended hinge spacing drawing page 8.
10
Piano Hinges
Removable pin and reversible pads for full or half surface application. Using three hinges, 9", 10", 13" and 17-3/4" suitable for 1-3/8" x 32" doors up to 90 lbs. 15-5/8", 17", 19-5/8" and 20-1/2" straps suitable for doors 1-3/4" thick x 36" wide up to 175 lbs.
Strap Hinges
Hinge Strap: Rough
Item Length Height Pad Width Pad GaugeBlack List
Ea
R5 9” 3-1/8” 1-3/8” 0.120 25.00R6 13” 3-1/8” 1-3/8” 0.120 27.00R7 17” 4” 2” 0.155 46.00R8 20-1/2” 4” 2” 0.155 53.00
RG 15-5/8” 4” 2” 0.155 49.00
RH 19-5/8” 4” 2” 0.155 53.00
Hinge Strap: SmoothItem Length Height Pad Width Pad Gauge List Ea
A5 10” 3-1/8” 1-3/8” 0.120 23.00
A6 13” 3-1/8” 1-3/8” 0.120 26.00
A8 17-3/4” 3-1/8” 1-3/8” 0.120 30.00
AN 15-5/8” 4” 2” 0.155 50.00
AP 19-5/8” 4” 2” 0.155 57.00
Dummy Hinge StrapsR1, R2, R3, RC, RD
ABADAF
Dummy Hinge Strap: Rough - use with butt hingesItem Length Strap Width at Hinge Gauge List Ea
R1 22-1/4” 1-9/16” 0.155 30.00
R2 18-3/4” 1-9/16” 0.155 28.00
R3 28-5/16” 3” 0.155 80.00
RC 8-3/4” 1-3/8” 0.155 10.00RD 14-1/4” 1-3/8” 0.155 19.00
RE 17-1/4” 1-9/16” 0.155 26.00
RF 21-1/4” 1-9/16” 0.155 29.00
Dummy Hinge Strap: Smooth - use with butt hingesItem Length Strap Width at Hinge Gauge List Ea
AB 14” 1-5/8” 0.155 18.00
AD 18-3/4” 1-5/8” 0.155 20.00
AF 24” 1-3/4” Alum 65.00
AG 31” 1-15/16” Alum 93.00
AL 17-1/4” 1-9/16” 0.155 26.00
AM 21-1/4” 1-9/16” 0.155 28.00
List Each
Black Clavos & Grille
List Each
Round Pyramid Square
ANAP
R5,R6R7,R8
A5, A6A8
RGRH
Piano Hinges Brass Nickel ORBITEM Open Width Length Brass List Nickel List ORB List
H11624 1-1/16” 24” 7.40 - -
H11636 1-1/16” 36” 11.00 - -
H11648* 1-1/16” 48” 14.00 24.00 -
H11672* 1-1/16” 72” 18.00 28.00 -
H11424 1-1/4” 24” 7.70 7.70 -
H11436 1-1/4” 36” 12.00 12.00 -
H11448 1-1/4” 48” 12.00 - -
H11472 1-1/4” 72” 14.00 14.00 -
H11224 1-1/2” 24” 8.40 8.40 -
H11236 1-1/2” 36” 12.00 - -
H11248 1-1/2” 48” 40.00 40.00 40.00H11272 1-1/2” 72” 55.00 55.00 55.00H20024 2” 24” 9.90 9.90 -
H20036 2” 36” 13.00 13.00 -
H20048 2” 48” 15.00 15.00 -
H20072* 2” 72” 18.00 18.00 -
Item Description ListCL34R 3/4” Round 3.10
CL118R 1-1/8” Round 3.80CL158R 1-5/8” Round 4.40CL1P 1” Pyramid 3.80CL158P 1-5/8” Pyramid 4.40CL118S 1-1/8” Square 4.40
CL158S 1-5/8” Square 4.40
Adhesive BackCL114RAD 1-1/4” Round 15.80
CL112RAD 1-1/2” Round 15.80
CL114PAD 1-1/4” Pyramid 15.80
CL112PAD 1-1/2” Pyramid 15.80
*H20072, H11648 Brass, H11672 Brass are closeouts - verify stock before selling
[email protected] 216-292-6555 store.bbwood.com 7B
Kick Plates
Push & Pull Plates
703-1/2" X 15"
70143-1/2" X 15"
Notes: 605 kick plates that are used on metal doors may discolor. To avoid this problem use Brass-tone.
Pull: 5-1/2" Ctr to Ctr on some models other models 6" ctr to ctr
Special Order Plates Listed Below - Allow 2 weeks - priced store.bbwood.com
86081 860823" x 12"
Code Finish Gauge 6x28 List 6x30 List 6x32 List 6x34 List 6x40 List 8x28 List 8x30 List 8x32 List 8x34 List 8x40 List
BT Brasstone Alum .04 26.00 27.00 29.00 31.00 36.00 32.00 34.00 36.00 39.00 45.00
505 Bright Brass-10Yr .05 101.00 105.00 115.00 119.00 144.00 130.00 139.00 148.00 153.00 185.00
605 Bright Brass .05 68.00 73.00 73.00 78.00 92.00 80.00 91.00 101.00 97.00 115.00
606 Satin Brass .05 70.00 75.00 75.00 80.00 94.00 81.00 93.00 102.00 99.00 116.00
609 Antique Brass .05 86.00 89.00 98.00 101.00 122.00 102.00 109.00 120.00 123.00 150.00
612 Satin Bronze .05 84.00 90.00 95.00 98.00 119.00 106.00114.00 125.00 129.00 156.00
613 Oil Rub Bronze .05 81.00 87.00 93.00 95.00 116.00 99.00 110.00 117.00 121.00 146.00
619 Satin Nickel .05 82.00 88.00 94.00 97.00 118.00 107.00 115.00 123.00 126.00 148.00
622 Black Anod Alum .04 26.00 27.00 29.00 31.00 36.00 32.00 34.00 36.00 39.00 45.00
626 Satin Chrome .05 85.00 89.00 98.00 104.00 122.00 103.00 107.00 118.00 121.00 147.00
628 Aluminum .05 22.00 23.00 25.00 26.00 31.00 25.00 26.00 29.00 30.00 35.00
629 Bright Stain Steel .05 48.00 52.00 55.00 59.00 69.00 62.00 66.00 71.00 75.00 88.00
630 Satin Stain Steel .05 21.00 23.00 24.00 26.00 30.00 27.00 29.00 31.00 33.00 39.00
630 Satin Stain Steel .038 22.00 24.00 26.00 27.00 32.00 28.00 30.00 32.00 34.00 40.00
670 Satin Nick Alum .04 25.00 27.00 29.00 31.00 36.00 32.00 34.00 36.00 38.00 45.00
716 Dark Anod Alum .04 26.00 27.00 29.00 31.00 36.00 32.00 34.00 36.00 39.00 45.00
620* Pewter .05 - - - 40.00 - - - - 38.00 -
Magnetic Backs: Add $27.00 per plate. Stock in 8x34 505 Stock in 8x34 619
Push/Pull Plates 70 List 7014 ListBright Brass 29.00 84.00Antique Brass 36.00 86.00
Satin Bronze 35.00 113.00Oil Rub Bronze 36.00 94.00Satin Nickel 36.00 114.00Pewter 64.00 114.00
Black 29.00 -
Bright Chrome 36.00 109.00Satin Chrome 30.00 101.00Aluminum 14.00 37.00Bright Stain Steel 19.00 67.00
Satin Stain Steel 12.00 50.00
86077 86078 8607986080 86118
Finishes: 505, 609, 613, 619, 620, 625. 613, 619 & Black
*Finish 620 close-out
Customs: Call for pricing. Max size 24x48 except BrassTone, 505, 629,630,628,670, 716 size 48x48
Bold Pricing Stock. Store.bbwood.com for stock status
3" x 12"
12 7B p: 216-292-6555 f: 216-292-6584
Flush Bolts Surface Bolts
3310 3300 3/4" X 6"; Throw: 1"
UL Flush Bolt
557
Dutch Door Hardware
4-1/4” Long
Replacement Strikes $6 ea.
Surface Bolts 3” 4” 6”- SB3 List SB4 List SB6 ListBright Brass 7.00 10.00 14.00Antique Brass 17.00 17.00 25.00Oil Rub Bronze 12.00 14.00 26.00Satin Nickel 20.00 17.00 25.00Pewter - 23.00 23.00Bright Chrome 10.00 10.00 15.00Satin Chrome 10.00 13.00 18.00
UL Extension Flush Bolt
1" X 6-3/4"; Throw: 1"Supplied with 12" Rod.*
1358
Flush Bolts 6” Square Radius3/4” X 6” 3310 List 3300 List
Bright Brass 15.00 12.00Antique Brass 16.00 12.00Oil Rub Bronze 15.00 15.00Satin Nickel 15.00 15.00Pewter 21.00 21.00Flat Black 21.00 21.00Bright Chrome 21.00 21.00Satin Chrome 14.00 14.00
Dutch Door Bolts-
4” Long Quadrant1630 List 56 List
Bright Brass 30.00 64.00Antique Brass 43.00 83.00
Oil Rub Bronze 36.00 83.00
Satin Nickel 43.00 83.00
Pewter 43.00 83.00
Black, Flat 43.00 83.00
Bright Chrome 29.00 83.00
Satin Chrome 29.00 83.00
1630 Bolt
56 Quadrant
Non-Handed
Projection: 1-1/4" Base: 2-3/4" x 1-1/4" *Height: 4-1/2" *Width: 4-3/8"
557 UL Flush Bolt1” x 6-3/4” List Price
Bright Brass 36.00Satin Brass -Antique Brass -Satin Bronze 43.00Oil Rub Bronze 41.00Satin Nickel -Pewter -Flat Black -Bright Chrome -Satin Chrome 42.00
1358 UL Flush Bolt *12”1” x 6-3/4” List Price
Bright Brass 31.00Satin Brass 43.00
Antique Brass 31.00Satin Bronze 31.00Oil Rub Bronze 31.00Satin Nickel 33.00Pewter 50.00Flat Black 33.00Bright Chrome 31.00Satin Chrome 29.00*18” Rod add 9.00
Notes: 609 & 622 finish in-clude 2 strikes & are 4" long
1" x 6-3/4" Throw: 3/4"
Manual 90 Min
Ansi A156.16, L04261
B&B Wood Products inc.
[email protected] 216-292-6555 store.bbwood.com 7B
Ball Catches Roller Catches
Hinge Door Stops
Durable nylon roller insures quiet operation.• Adjustable ten-sion.• Easily installed on thin doors.• Conforms to ANSI/BHMA A156.16 L27081
Dimensions: Face Plate: 2-1/4" x 7/8" Bore: 13/16" x 1-3/4" Strike: 2-1/4" x 1-5/8" Lip 1-13/16" to center
335
4-7/8" x 1-1/4"
1704
347Faceplate 1" x 2-1/8" Strike 2-1/8" x 1-3/8"
Lip 7/8" to center.
A. Free rolling ball insures smooth, positive and trouble-free action.B. Adjustable barrel to compensate for various clearances of doors.C. Adjustable spring tension for any action.
Conforms to ANSI/BHMA A156.9 B23013
Ball Catches347 List
DB75 List
Strike List
Bright Brass 17.00 6.00 5.00 Antique Brass 18.00 6.00 5.00 Satin Bronze 19.00 - -Oil Rub Bronze 19.00 6.00 5.00 Satin Nickel 18.00 6.00 5.00 Pewter 20.00 6.00 5.00 Black 19.00 - 5.00 Bright Chrome 19.00 - 5.00 Satin Chrome 19.00 6.00 5.00
• Positive slip proof adjustment. • Accommodate 1/4" to 5/16" diam. hinge pins.
69
Hinge Stops 4210 List 69 List 1503 List 9507 List
Bright Brass 1.60 5.80 2.40 9.90Antique Brass 3.30 5.80 3.30 -Satin Bronze 3.30 5.80 - -Oil Rub Bronze 1.60 5.50 2.40 10.50Satin Nickel 1.60 5.50 2.40 9.90Pewter 3.60 5.80 3.30 -Bright Chrome 2.40 5.80 2.40 9.90Satin Chrome 2.40 5.80 2.40 -Black 2.40 5.80 2.40 -White 15.80 - - -
DBC-75
1" Drive-in
Radius Corner Strike
1-11/16" x 2-1/4" 1-3/4" x 2-3/4"
17021700
Face Plate: 3-3/8" x 1"
1503
4210
Roller Catches335 List
1700 List
1702 List
1704 List
Bright Brass 19.20 37.00 38.00 38.00
Antique Brass 22.90 41.00 42.00 42.00
Satin Bronze - 44.00 - -
Oil Rub Bronze 22.90 41.00 42.00 42.00
Satin Nickel 23.90 44.00 44.00 67.00
Pewter 19.00 55.00 55.00 67.00
Black - 50.00 61.00 67.00
Bright Chrome 24.30 50.00 61.00 67.00
Satin Chrome 22.90 30.00 31.00 31.00
9507
Bold Pricing Stock. Store.bbwood.com for stock status
Replacement Strikes Ball Catches: List $6.00
14 7B store.bbwood.com 216-292-6555 [email protected]
440 - For doors without thresholds. 1" Height.
442- For doors with thresholds. 1¼" Height.
FLOOR DOOR STOPS
4635 - 1-3/8" Height.
DOOR STOP - SOLID
DOOR SPRING STOP - Heavy Duty
DOOR HOLDER - Heavy Duty
407
Wall Bumper 407 ListBright Brass 5.30Antique Brass 6.70Satin Bronze 6.70Oil Rub Bronze 6.00Satin Nickel 6.00Pewter 11.70Bright Chrome 6.30Satin Chrome 5.90
WALL BUMPER
Floor Stop 440 List 442 ListBright Brass 8.50 11.10Antique Brass 8.80 11.10Satin Bronze 10.10 12.60Oil Rub Bronze 9.80 11.50Satin Nickel 9.80 14.60Pewter 16.00 20.00Bright Chrome 9.20 11.80Satin Chrome 8.00 8.90
FLOOR DOOR STOP
- - SOLID BRASS
Solid Stop 4680 List 60 List 62 ListLength 3-3/4” 3-3/4” 4-1/2”
Bright Brass 5.00 16.10 12.00Antique Brass - 17.10 -Oil Rub Bronze 5.00 21.00 -Satin Nickel 5.00 21.00 -Pewter - 28.00 -Bright Chrome - 22.30 14.30Satin Chrome - 22.30 14.30Black 5.00 22.30 -
Drop Arm 5” 4649 ListBright Brass 16.40Satin Nickel 16.40Oil Rub Bronze 16.40
1" WALL BUMPER
• Fasteners: 1 - #8x1"SMS, 1-Brad nail & Plastic Anchor
Wall Bumper 1400 ListSatin Chrome 7.90ORB, Chrome, Satin Brass 12.40
FS448 Heavy Duty Stop
Floor StopFS448
ListBright Brass 41.00Oil Rub Bronze 40.00Satin Nickel 51.00Bright Chrome 62.00Satin Chrome 41.00Black 51.00
• Cast brass construction.• Accommodates door undercut up to 2-1/2".• Non-marring rubber tip.• Packed with wood screws.• Meets ANSI/BHMA 156.16, L12121
Height 3" Base Diam 2-1/2"
Spring Stop 4217 List4674 ListLength 3-1/8” 3-3/4”
Bright Brass 0.94 2.10Antique Brass 1.70 2.00Satin Bronze 1.80 -Oil Rub Bronze 0.94 1.60Satin Nickel 0.94 1.60Pewter 2.40 2.20Bright Chrome 1.14 1.90Satin Chrome 1.14 1.90Black 1.70 1.90
Item may differ from photo
1-3/8"Floor Stop 4635 ListBright Brass 4.80
1400: 1" Diameter• Base Material Brass • 1/2" projection
• Meets ANSI A156.16, L02101
62 is a close-out
Concealed attachment 2-1/2" Diameter
1" Projection
Item may differ from picture
[email protected] 216-292-6555 store.bbwood.com 7B
HANDRAIL BRACKETS
Door Viewers B4825 List
B4820 List
180⁰ 160⁰Bright Brass 14.30 3.60Antique Brass 18.00 -
Oil Rubbed Bronze 14.30 -Bright Nickel 18.00 7.20Satin Nickel 14.30 -
DOOR VIEWERS
FEATURES• Projects 1/4” from face of door • Bore size is 9/16” hole.• Fits 1-3/8” to 2-1/4” doors.• UL - 1 Hour
B4825 - 1800 View B4820 - 1600 View
• Bore size is 1/2” .• Fits 1-5/16” to 2-1/8" doors
FEATURESCoat Hooks 4230
List7305 List
3” 5”
Bright Brass 1.70 7.00Antique Brass 2.60 -'--Oil Rubbed Bronze 3.40 9.00Satin Nickel 2.60 -Pewter*/Satin Bronze* 2.70 -Nickel - 7.00
Satin Chrome* 2.40 -
HR601 Plated Base to Center of Rail 2-3/4"
Exceeds OHSA/BHMA strength test.
Base to Center of Rail 2-1/4"
HR159 Solid Brass
meets ANSI/BHMA A156.16, L13081.
COAT & HAT HOOK
HR312 Plated Base to Center of Rail 3-1/2"
Long Arm Bracket
HR301 Powder Coat Base to Center of Rail 3-1/4"
HR158- Plated Base to Center of Rail 3-3/8"
Long Arm Brackets
HR4235 - Diecast Base to Center of Rail 2-1/4"
HR059B Solid Brass Base to Center of Rail 2-7/16"
HR059A Cast AluminumBase to Center of Rail 2-7/16"
7305 5" High
Item may vary from picture
*Subject to availability
4230
3" Projection
HR606 Plated Base to Center of Rail 2-3/4"
-HR4235
ListHR059A
ListHR059B
ListHR312
ListProjection 2-1/4” 2-7/16” 2-7/16” 3-1/2”
Bright Brass 3.90 4.70 24.50 7.20Antique Brass - 4.70 37.20 -Satin Bronze - 4.70 - -Oil Rub Bronze 3.70 4.70 28.80 10.30Satin Nickel 3.70 4.70 28.80 11.20Pewter 3.90 - 30.70 -Bright Chrome 5.00 - 34.90 -Satin Chrome 3.50 4.70 33.80 -Black - 6.20 - -White - 6.60 - -
For pricing store.bbwood.com
HR601 List
HR606 List
HR158 List
HR159 List
2-3/4” 2-3/4” 3-3/8” 2-1/4”7.10 13.00 13.00 31.709.30 - - -
- - - 31.709.60 13.00 13.00 38.109.60 13.00 13.00 38.1013.00 - - 38.1010.30 - - -10.20 - - 39.708.10 - - -
11.00 - - -
16 7B store.bbwood.com 216-292-6555 [email protected]
FLUSH PULLS
P2181" Diam.
P221: 2-7/16" Diam
P223: 1-5/16" x 3-9/16"
P227: 1-3/4" x 3-5/8"
P222: 1-5/16" x 3-1/8"
Flush PullP218 List P221 List P222 List P223 List P227 List
Bright Brass 2.90 4.50 26.00 8.00 11.90Antique Brass - 4.80 29.80 11.00 14.10Satin Bronze 6.30 - - - 17.80Oil Rub Bronze 6.30 5.40 29.80 9.00 13.80Aged Bronze - 5.60 - - -Satin Nickel 4.00 5.20 28.80 8.60 13.30Pewter 5.40 6.70 25.00 11.00 -
Black 5.40 5.70 29.80 9.60 14.70
Bright Chrome 5.40 5.70 29.80 9.60 14.70Satin Chrome 5.40 5.70 29.80 9.60 14.70
P42
POCKET DOOR BOLT - P42
Pocket Bolt P42 ListBright Brass 18.00Antique Brass 20.00Oil Rub Bronze 20.00Satin Nickel 20.00Pewter 20.00
Black 20.00Bright Chrome 20.00Satin Chrome 20.00
• Ideal for single or pairs of doors to provide privacy function.• Emergency release of bolt is accomplished by drilling a small hole in the door (grommet provided). A thin object inserted into the hole will push the rocker back to the unlocked positon.
OA 3-1/16” x 1-5/32”Strike: 1” x 3/4”Depth of Mortise: 5/8”
EDGE PULL - P230
Edge Pull P230 ListBright Brass 17.00Antique Brass 20.00Satin Bronze 18.00Oil Rub Bronze 20.00Satin Nickel 19.00Pewter 19.00Black 20.00Bright Chrome 20.00Satin Chrome 20.00
P230
Sliding & Pocket Door Accessories
Mounted on the jamb side of a pocket door. It works like a rocker switch. When pushed in, the other half pops out, physi-cally preventing the door from returning into its pocket. A strike is provided to protect the jamb.
Door Edge Jamb
3/4” x 3-7/8”
Item Size List
P221SQ 2-1/2” x 2-1/2” 20.60
P2276 1-3/4” x 6” 37.50
P2277 2” x 7” 42.30
P22710 2” x 10” 60.50
The following are available in: Polished Brass; Satin Brass; Antique Brass; Oil Rubbed Bronze; Polished Nickel; Satin Nickel; Pewter; Flat Black; Polished Chrome
P2276 P2277 P22710
P221SQFits std 2-1/8"
diam. hole
Fits 2-1/8" diam. hole
Fits 3/4" hole
17
Sliding & Pocket Door Locks
PDL100 Passage
PDL101 Privacy
P1521 Privacy/Passage: *1-3/8" thick doors• Uses 2-1/8" Bore & 2-3/8" backset like swinging doors• Automatic latching when shut• All units fully reversible• Ideal for double door pockets. A "P1521" is used in one
door, matching "P21" dummy pulls in the other. Edge pulls are recommended.
TUBULAR POCKET DOOR LOCK
Tubular Pocket P1521 List P21 ListBright Brass 24.00 12.00Satin Nickel 24.00 11.00Black 27.00 10.00
PDL100 List
PDL101 List
PDL101-134 List
PDL2101 List
PDL2102 List
Door Thickness up to 1-3/4” 1-3/8” up to 1-3/4” up to 1-3/4” up to 1-3/4”
Bright Brass 12.50 15.00 18.00 38.80 51.30
Antique Brass 13.70 17.00 20.00 38.80 51.30
Satin Bronze 13.50 15.00 - - -
Oil Rub Brz 13.50 15.00 18.00 38.80 51.30
Aged Bronze 19.40 27.00 - - -
Satin Nickel 15.90 20.00 23.00 38.80 51.30
Pewter 17.70 21.00 24.00 38.80 51.30
Black 17.30 21.00 24.00 38.80 51.30
Bright Chrome 12.50 14.00 17.00 38.80 51.30
Satin Chrome 12.80 14.00 17.00 38.80 51.30
Door cut out 1-3/4" deep x 2-1/4" high
PDL2101 Passage
PDL2102 Privacy
Door cut out 1-3/4" deep x 3-1/8" high
MORTISE POCKET DOOR LOCKS
PDL210 Classic PDL211 Modern
Specify thickness of door on Keyed and Privacy. Plate thickness 1/16". Dummy set will accept latch from keyed and privacy. Requires 3-7/8" deep mortise pocket in stile. Keylocks cannot be keyed to other Emtek keyways.
Polished Brass; Oil Rub Bronze; Satin Nickel; Pewter; Polished Chrome, Medium Bronze, Tumbled White Bronze
Polished Brass; Satin Brass; French Antique; Oil Rubbed Bronze; Polished Nickel (618); Satin Nickel; Pewter; Flat Black; Polished Chrome
PDL2103 PDL2113 KeyedPDL2104 PDL2114 PassagePDL2105 PDL2115 PrivacyPDL2106 PDL2116 Dummy
Priced on store.bbwood.com
*see store.bbwood.com for more designs & 1-3/4" doors
[email protected] 216-292-6555 store.bbwood.com 7B
Pocket track and hardware is priced on page 27
B&B Wood Products inc.
Above strikes are available with radius corners. Add $3.00 List.
18 7B store.bbwood.com 216-292-6555 [email protected]
2-1/4" Extended Lip Strike (EL-1)
2-3/4" Extended Lip T-Strike (ETS)ANSI Strike Size
Stain Steel List
Dark Brz List
EST175 4-7/8” X 1¾” 26.00 31.00
EST102 4-7/8” X 2” 26.00 31.00
EST125 4-7/8” X 2½” 26.00 31.00
EST103 4-7/8” X 3” 26.00 31.00
EST104 4-7/8” X 4” 31.00 36.00
0" 1-¾" 2" 2-½" 3" 4"
4-7/8"
4-7/8" Extended Lip ANSI-Strike (EST)
2-3/4" Extended Lip Strike (EL-2)
Full Lip SizeBright
Brass ListAnt Brass
ListSatin
Nick ListPewter
ListStain Steel
ListDark Brz
ListEL115 2¼’ X 1½” 9.00 13.00 13.00 14.00 8.00 15.00EL175 2¼’ X 1¾” 9.00 13.00 13.00 14.00 8.00 15.00EL102 2¼” X 2” 9.00 13.00 13.00 14.00 8.00 15.00EL125 2¼” X 2½” 9.00 13.00 13.00 14.00 8.00 15.00
EL103 2¼” X 3” 9.00 13.00 13.00 14.00 8.00 15.00EL104 2¼” X 4” 21.00 27.00 27.00 28.00 20.00 25.00
Full Lip SizeBright
Brass ListSilver List
Dark Brz List
EL202 2¾” X 2” 14.00 14.00 14.00EL225 2¾” X 2½” 14.00 14.00 14.00
EL203 2¾” X 3” 14.00 14.00 14.00EL204 2¾” X 4” 17.00 18.00 18.00
EL205 2¾” X 5” 17.00 18.00 18.00
T-Strike SizeBright
Brass ListAnt. Brass
ListStain
Steel ListDark Brz
ListETS102 2¾” X 2” 11.00 14.00 9.00 13.00ETS125 2¾” X 2½” 11.00 14.00 9.00 13.00
ETS103 2¾” X 3” 11.00 14.00 9.00 13.00
ETS104 2¾” X 4” 21.00 28.00 20.00 25.00
Extended Lip Strikes, Custom Strikes &Thimble Strike
Thimble Strike Brass List
Chrome List
TS1000 1” Diameter 5.30 5.30
1" DiameterThimble Strike Custom Strikes• Made to your specifications• Any finish• For mortise or cylindrical locks
1½"
Bold Pricing Stock. Store.bbwood.com for stock status
B&B Wood Products inc.
[email protected] 216-292-6555 store.bbwood.com 7B
ANSI Strike Filler Plate4-7/8" X 1-1/4"
Hole Filler PlatesCovers up to 2-1/2" hole86 Mortise Filler Plate
Latch & Hinge Filler Plate
ANSI Filler Strike Prime List
FS260 4-7/8” X 1-1/4” 2.90
86 Mortise Filler Plate Prime List
CV86 8” X 1-1/4” 11.40
CV8624 8” X 1-1/4” 23.50
1,2,3,4 5,6,7,8 154, 264, 484: 4" OC
51,61, 71,81
2-1/8" Hole 1-1/2" Hole 2-1/8" Holes2-1/8" Hole 1-1/2", 2-1/8" Hole151, 261, 481:
3-5/8 OC256, 258: 5 ½" OC
Item Backset Door SizeBrass List
Antique Brass List
Satin Brz List
Oil Rub Bronze List
Stainless Steel List
1 2-3/8” 1-3/8” 4” x 9” 40.00 57.00 57.00 54.00 35.002 2-3/8” 1-3/4” 4” x 9” 37.00 53.00 53.00 50.00 33.003 2-3/4” 1-3/8” 4¼” x 9” 40.00 57.00 57.00 50.00 35.004 2-3/4” 1-3/4” 4¼” x 9” 37.00 53.00 53.00 50.00 33.005 2-3/8” 1-3/8” 4” x 4½” 27.00 42.00 39.00 40.00 23.00
6 2-3/8” 1-3/4” 4” x 4½” 25.00 39.00 39.00 40.00 21.007 2-3/4” 1-3/8” 4¼” x 4½” 27.00 42.00 42.00 40.00 23.008 2-3/4” 1-3/4” 4¼” x 4½” 25.00 39.00 39.00 40.00 21.00
51 2-3/8” 1-3/8” 4” x 4½” 27.00 42.00 42.00 40.00 23.0061 2-3/8” 1-3/4” 4” x 4½” 25.00 39.00 39.00 40.00 21.0071 2-3/4” 1-3/8” 4¼” x 4½” 27.00 42.00 42.00 40.00 23.00
81 2-3/4” 1-3/4” 4¼” x 4½” 25.00 39.00 39.00 40.00 21.00151 2-3/8” 1-3/8” 4” x 9” 40.00 57.00 57.00 50.00 35.00
261 2-3/8” 1-3/4” 4” x 9” 37.00 53.00 53.00 50.00 33.00
481 2-3/4” 1-3/4” 4¼” x 9” 40.00 53.00 53.00 50.00 33.00
256 2-3/8” 1-3/4” 4” x 12” 48.00 59.00 59.00 58.00 44.00
258 2-3/4” 1-3/4” 4¼” x 12” 51.00 59.00 59.00 58.00 44.00
154 2-3/8” 1-3/8” 4” x 9” 37.00 53.00 53.00 50.00 33.00
264 2-3/8” 1-3/4” 4” x 9” 40.00 53.00 53.00 50.00 33.00484 2-3/4” 1-3/4” 4¼” x 9” 37.00 53.00 53.00 50.00 33.00
Protective plate that attaches permanently to any OUT-SWING wood or hollow metal door. It completely covers the latch area to protect it from being tampered with by intruders.• PLP: A solid steel pin prevents the door from being pried
open from the frame. Fits 2-3/8" or 2-3/4" backsets• NLP: Narrow but long enough to cover mortise pockets• CLP: Concealed Welded Studs with fasteners which is
long enough to cover mortise pockets.
CLP 2-1/8" X 10" NLP 1-1/2" X 10"
PLP 3" X 11"
Filler Plates, Reinforcers, Protectors
Latch & Edge Protectors
Door Reinforcers
Converts Mortise pocket to 161 Cyl. lock(s)
CV86 CV8624
Hole Filler Plate Brass List
Prime List
Chrome List
BF161 Up to 2-1/2” 8.00 5.00 7.00
Item DescriptionSilver List
Brass List
PLP211 Pin Latch Protector for Outswing 20.00 -CLP110 Commercial for Outswing 34.00 -NLP210 Narrow Commercial for Outswing 29.00 -DR10 Edge Reinforcer 1-3/8” Door 16.00 19.00DR20 Edge Reinforcer 1-3/4” Door 16.00 19.00
CV8624 bores are 4" on center
DR10 & DR20: Edge Reinforcers: Height 4-1/2"; Center to center screws 1-5/8"; Latch holes 7/8" wide; Side Projedion 1"
Latch & Hinge Filler Plate Brass List
Prime List
EF160 1” x 2-1/4” 5.60 6.10EF161 1-1/8” x 2-1/4” 5.60 6.10FF45 4-1/2” x 1-5/8” - 3.50FB225 15/16” x 2-1/4” 5.60 3.50
20 7B store.bbwood.com 216-292-6555 [email protected]
Letter Size Plates
Magazine Size Plates
L627 - Spring loaded front plate and gravity back plate. Plate Opening: 7” x 1-1/2”. Overall 8-7/8" x 2-7/8".
L626 - Spring loaded front plate and standard back plate. Plate Opening: 7” x 1-1/2”. Overall 8-7/8" x 2-7/8".
-L626 List
L627 List
L620 List
L212 List
L30 List
L158 List
L601 List
Bright Brass 92.00 114.00 100.00 168.00 225.00 73.00 -Antique Brass 92.00 114.00 105.00 168.00 225.00 73.00 -
Oil Rub Bronze 92.00 114.00 105.00 168.00 225.00 73.00 -Aged Bronze - - 120.00 - - - -Satin Nickel 92.00 114.00 105.00 168.00225.00 73.00 -Pewter 92.00 114.00 105.00 168.00 225.00 73.00 -
Black 92.00 114.00 105.00 168.00 225.00 73.00 -
Bright Chrome 92.00 114.00 105.00 168.00 225.00 73.00 -Satin Chrome 92.00 114.00 105.00 168.00 225.00 73.00 -
Stainless Steel - - - - - - 37.00
No. L620 - Spring loaded front plate and standard back plate. Plate Opening 11" x 2”. Overall 13" x 3-9/16”.
No. L212 - Spring loaded front plate and covered back plate. Plate Opening 11" x 2”.. Overall 13" x 3-9/16”..
No. L30 - Front plate assembly and standard back plate. Plate Opening 11 x 2”. Overall 13" x 3-1/16".
L601 - sold separately
Options:
For 1-3/4" doors
L158 - Interior Hood sold separatelySize 12-3/4 x 3-1/4”
For 1-3/4" doors
For 1-3/4" doors
L601 - sold separately
L601 - sold separately
+
+
+
+
[email protected] 216-292-6555 store.bbwood.com 7B
SPECIFICATIONS & FEATURES: 2-step speed adjustment closes any door softly, latches securely every time. Reversible for right or left hand openings; outswing or inswing doors. Low-profile design with exclusive slide-track arm fits flush; does not protrude into room. No springs to wear out; no oil to leak. SN123/HO is ideal for all interior and exterior doors. Two year warranty.
Series S50 Includes parallel arm bracket
Door Closers
Option:Item ListThru-Bolts (set of 4) Add $8
WARRANTY: Each closer is backed by a 25-year limited warranty when used with ball bearing hinges.
Hold Open Finish List PriceSN123HO Silver, Black, White, Brown $61.00 Max Door Width 3’6”
Max Door Weight 150 lbs.
Max Open Angle Door Mount 169°
Max Angle at which Hold-Open Engages 110°
SN123 Door CloserParallel Arm InstallationStandard Installation Top Jamb Installation
Spray Finish: Aluminum or Dark Bronze.
All 50 Series closers have aluminum alloy bodies with high compression steel springs for doors opening 180° maximum. The closers have two non-critical thermostatic valves to separately control sweep and latch speeds and provide constant dosing speeds. S51BF-BC closers have adjustable spring power from sizes 1 thru 4 and comply with 5 Ib. interior and 8 1/2 Ib. exterior barrier-free opening force restrictions. All S52 thru S55 closers have fixed spring sizes. The closers can be installed in regular, top jamb and parallel arm applications. Min door rail for closer 2-3/8". Width of closer is 9-11/16"; Projection is 2-7/8"
Cross Reference: Norton 9000; LCN 1070; Dorma 642-645; Corbin DC2600; Sargent 1100; Yale 2300
Door Width 26" to 30" 30" to 36" 36" to 42"
Exterior 53 or 5014 5014 55 or 5036
Interior 52 or 5014 53 or 5014 5036
Selection Chart:
Series 50 SizeSilver List
Brown List
S52BC 2 see 5014 $83.00
S53BC 3 see 5014 $83.00
S55BC 5 $83.00 $83.005014 Adjustable ADA 1-4 $86.00 $86.005036 Adjustable ADA 3-6 $86.00 $86.00
Medium-duty applications like retail storefronts, cafes and clinics. The Falcon SC80 Series brings ANSI Grade 1 durability and reliable performance to interior and exterior storefronts. ADA compliant.Butt Hinges should not exceed 5” (127mm) in width. Auxiliary Stop is recommended at hold-open point or where a door cannot swing 180°. Top Rail less than 4-3/8” measured from stop requires plate SC80-18PA• Meets ANSI A117.1• ANSI/BHMA A156.4, Grade 1• UL Listed• 1-1/4” diameter piston• Closer mounts hinge side, top jamb or parallel arm with the Rw/PA arm• Fully adjustable sizes 1-6• Single piece cast aluminum body• Non-handed• Separate adjustable general speed, latch speed and backcheck• Cover is high-impact UL Listed fire retardant plastic that meets UL 10C and UBC 7-2 (1997) fire test• UL 10C approved fluid• Universal screw pack• 10-year warranty• Available in 695 (Dark Bronze) or 689 (Aluminum) finishes
Door Closers - Medium Duty
priced on http://store.bbwood.com/SC80.aspx
Item Bifold Kit 1825 doors to 35 lbs. each List1825-24 2-Drs for opening 24” 13.001825-30 2-Drs for opening 30” 13.001825-32 2-Drs for opening 32” 14.001825-36 2-Drs for opening 36” 14.001825-48 4-Drs for opening 48” 25.001825-60 4-Drs for opening 60” 25.001825-72 4-Drs for opening 72” 26.001825-84 4-Drs for opening 84” 29.001825-96 4-Drs for opening 96” 33.00Item Bifold Kit BF50 doors to 50 lbs. each ListKit.BF50.24 2-Drs for opening 24” 35.00Kit.BF50.30 2-Drs for opening 30” 35.00Kit.BF50.36 2-Drs for opening 36” 35.00Kit.BF50.48 4-Drs for opening 48” 54.00Kit.BF50.60 4-Drs for opening 60” 58.00Kit.BF50.72 4-Drs for opening 72” 62.00Kit.BF50.96 4-Drs for opening 96” 76.00Item Bifold Kit BF125 doors to 125 lbs. each ListKit.BF125.24 2-Drs for opening 24” 54.00Kit.BF125.30 2-Drs for opening 30” 56.00Kit.BF125.36 2-Drs for opening 36” 58.00Kit.BF125.48 4-Drs for opening 48” 108.00Kit.BF125.60 4-Drs for opening 60” 112.00Kit.BF125.72 4-Drs for opening 72” 116.00Kit.BF125.96 4-Drs for opening 96” 125.00
Bifold Kits include track, pivots and hangers. Hinges sold separately.
Bifold Hardware
Optional BF1705
BF1050 Track
BF125N-51
Series BF-125
Series BF-50
Up to 50 lbs. each doormax. 2-doors to a jamb .Up to 30 lbs. each doorfor 2+ drs to a jamb.Finish Opening height: Door height +2-3/8"
Up to 125 lbs. each doormax. 2-doors to a jamb .Up to 75 lbs. each doorfor 2+ drs to a jamb.Finish Opening height: Door height +2-7/8"
Finish Opening height: Door height + 1-3/4"
Up to 35 lbs each door max. 2-doors to a jamb
Series BF-1825
BF50-41
1-13/16"
1-1/2" min. 2" max.
1-1/2" min.
1-1/2" min.
3/4" min. 1-7/16" max.
Meets ANSI A156.14 type D8621, D8641, D8651, D8661
BF50-HDW
Series BF-50
1-3/4" min.
5/8" min. 1-1/4" max.
1-13/16"
1-3/4" min. 2-3/8" max.
1-3/4" min.
1-3/16"
Meets ANSI A156.14 type D8621, D8642, D8652, D8661
Series BF-125
1825 kits are not adjustable in height
22 7B [email protected] p: 216-292-6555 f: 216-292-6584
B&B Wood Products inc.
Parts used across all series ListBF1805 Hinges (price per pair) 2.03BF1808 or BF50-72 pr 4-Dr Aligner (1 set) 1.00BF50-36 Birch Knob Each 1-3/4” diam. 0.90BF50-60.WH White Plastic Knob Each 1-3/4” diam. 0.60BF50-60.BRN Brown Plastic Knob Each 1-3/4” diam. 0.60BF50-60.TAN Tan Plastic Knob Each 1-3/4” diam. 0.60BF1705 Guide Roller for BF1050 Each 1.30BF1050 Bottom Guide Channel-8’ Each 14.20
Bifold BF125N Parts ListBF125N-01-48 48” Track 16.00BF125N-01-60 60” Track 20.00BF125N-01-72 72” Track 24.00BF125N-01-96 96” Track 33.00BF125-21 2-Dr Snugger 2.00BF125N-51 1-Hanger & 1-Pivot 46.00
Bifold BF50 Parts ListBF50-01-48 48” Track 16.00BF50-01-60 60” Track 20.00BF50-01-72 72” Track 24.00BF50-01-96 96” Track 38.00BF50-HDW Pivot Set 8.00BF50-11 Top Pivot Bracket 2.00BF50-22 2-Door Snugger 2.00BF50-24 4-Door Snugger 2.00BF50-33 Bottom Pivot 2.00BF50-34 Top Pivot 2.00BF50-41 Hanger - 2 wheel & guide wheel 11.00BF50-81 Jamb Bracket 2.00BF50-299 Wrench 1.10
1825 Series Parts ListBF1801 Top Pivot Guide 1.40BF1804 Bottom Pivot Bracket 2.40BF1807 Bottom Pivot 1.30BF1810 Top pivot bracket 1.80BF1811 Bottom Pivot Jamb Bracket 1.80BF1836 Carpet Riser for use with 1811 1.30BF1861 Bottom Pivot Jamb Bracket 1.101712 Wrench 0.40
BF30-25
1805
BF50-22 BF50-24
BF50-11
BF50-81
BF50-36 BF50-60 BF1705
1808 BF50-72
BF50-33 BF50-34
BF125-21 BF125N-51
BF50-41
BF1050
BF50-HDW
1804
1810
1801
1861
1807 1811
[email protected] 216-292-6555 store.bbwood.com 7B
Multi-Fold Hardware
Door Thickness: 1-1/8" to 1-3/4". Max Door Weight: 75 lbs. ea. Max Dr Size: 36" x 108"Multi-folding door hardware set designed to carry large heavy panels. Precision extruded aluminum 'I' beam track is available in 8' lengths (per quote up to 16'). Heavy duty pivots and guides effectively control heavy panel movement and facilitate smooth operation. 11-13 gauge zinc dichromate plated steel components for a quality appearance and corrosion resistance. 6 panels max. each direction. Minimum door width 12"Order: A) Track B) 2015BS-A" for first set of panels from jamb. C) "2002PLBG" for every pair of panels after 1st pair. Hinges sold separately - Order Ball Bearing Mortise.
Designed to work with even number of door panels only (2, 4 or 6) from each direction or converging (4, 8 or 12) panels configu-rations from two directions. Multi-folding door hardware can be mounted to the top of door panels in the following ways.
Doors hung from top center of each panelDoors hung from top edge of each panel
For panels up to 24" wide & 108" tall. Track is available in 8' lengths (per quote up to 16'), available with optional bottom track for extra rigidity. Convex aluminum track, 14-16 gauge plated steel components. Includes positive pivot lock, top hung three-wheel 1" dia. ball-bearing hangers, non-mortise lift off hinges and adjustable floor mount bottom pivot bracket. 6 panels max. each direction. Minimum door width 12".Order: A) Track B) "1015BS-A" for first set of panels from jamb. C) "1030AOSB" for every pair of panels after 1st pair. Surface hinges included.
Door Thickness: 1" to 1-3/4". Max Door Weight: 50 lbs. ea. Max Dr Size: 24" x 108"100RD Series
Finish Height = Door height + 2-7/8"
Finish Width = # of Doors X (Dr Width + 1/16") + 9/16"Finish Height = Door height + 4-1/4"
1015BS-A
1030AOSB
100 Track
200RD Weight: 75 lbs. each, Max Size: 3’x9’ (hinges extra) List
2015BS-A Basic Set A 83.002002PLBG Addon set B 47.00200-8 Track 96” long 75.00
100RD Weight: 50 lbs. each, Max Size: 2’x9’ (includes hinges) List
1015BS-A Basic Set 60.001030AOSB Add on Set B 61.00100-8 Track 96” long 33.00
2002PLBG
2015BS-A
200 Track
Contact office for Track in 36", 48", 60", 72" 106", 120", 144", 192" lengths
200RD Series
Contact office for Track in 36", 48", 60", 72" 106", 120", 144", 192" lengths
24 7B store.bbwood.com 216-292-6555 [email protected]
B&B Wood Products inc.Bypass Door Hardware (parts see page 26)
Finished Opg. Height = Door + 1-3/4"
1-3/8"DOOR
1-3/8"DOOR
2-13/16"
1-5/8"1-1/4" to1-9/16"
2228 3/4" pulls
4"
1-3/4"DOOR
1-3/4"DOOR
2-3/16"1-3/4"to2-1/4"
Finished Opg. Height = Door + 2-3/8"
1120 2-1/8" pulls
Upgrade to 200 lbs with 4-1125 (pg 26)
Upgrade to Soft-Close with 4-1060SOFT
3/4"DOOR
3/4"DOOR
1-7/8"
1-1/4" to1-9/16"
1-1/8"1-3/8"DOOR
1-3/8"DOOR
7/8" 1-7/8"
1-1/8" 1-1/4" to1-9/16"
2216, 2238 3/4" pulls
Finished Opg. Height = Door + 1-3/4"
Finished Opg. Height = Door + 2-5/8"
Upgrade to Soft-Close order 4 - 6320 (pg 26)
1-3/16" 1-3/4" min.
2-3/8" max.
3-5/8" on 1-3/8" thick3-15/16" on 1-3/4" thick
Flush pulls not included.
Meets ANSI A156.14 type D8731
Sets include 2 tracks, 2 pr. hangers, Dr. Guide, wrench and screws.
For doors to 50 lbs each. 3/4” or 1-3/8” thick doors. Steel Gold Track - No Fascia Description List1166-48 For Two 2’0” Doors 18.101166-60 For Two 2’6” Doors 21.001166-72 For Two 3’0” Doors 23.801166-96 For Four 2’0” Doors 46.00Aluminum Track - No Fascia Description List2200-48 For Two 2’0” Doors 22.002200-60 For Two 2’6” Doors 25.002200-72 For Two 3’0” Doors 28.002200-96 For Four 2’0” Doors 49.00
For doors to 75 lbs each. 1-3/8” thick doors. Aluminum Track with Fascia Description List2200F-48 For Two 2’0” Doors 27.002200F-60 For Two 2’6” Doors 32.002200F-72 For Two 3’0” Doors 36.002200F-96 For Four 2’0” Doors 61.00
For doors to 125 lbs each. 1-3/4” thick doors. Aluminum Track with Fascia Description List134F-48 For Two 2’0” Doors 73.00134F-60 For Two 2’6” Doors 82.00134F-72 For Two 3’0” Doors 90.00134F-96 For Four 2’0” Doors 146.00For 1-3/8” to 2-1/4” thick doors. Track is made up of 2 pieces150 Lbs. Aluminum Track Description ListKit.BP150-48 For Two 2’0” Doors 68.05Kit.BP150-60 For Two 2’6” Doors 74.05Kit.BP150-72 For Two 3’0” Doors 82.05Kit.BP150-96 For Two 4’0” Doors 98.05250 Lbs. Aluminum Track Description ListKit.BP250-48 For Two 2’0” Doors 82.05Kit.BP250-60 For Two 2’6” Doors 88.05Kit.BP250-72 For Two 3’0” Doors 96.05Kit.BP250-96 For Two 4’0” Doors 112.05
Price is for pair of top and bottom track-Tan Color
1/4"
1/2"
Plastic Bypass Track for Plywood PanelsItem Description ListM14.48 For 1/4”: Two 2’0” Panels 7.40M14.72 For 1/4”: Two 3’0” Panels 9.30M14.96 For 1/4”: Two 4’0” Panels 13.90M12.48 For 1/2”: Two 2’0” Panels 11.00M12.72 For 1/2”: Two 3’0” Panels 13.70M12.96 For 1/2”: Two 4’0” Panels 20.40M34.48 For 3/4”: Two 2’0” Panels 14.10M34.72 For 3/4”: Two 3’0” Panels 18.20M34.96 For 3/4”: Two 4’0” Panels 24.40
[email protected] 216-292-6555 store.bbwood.com 7B
The 1060 Kit contains a single soft-close actuator for use on 100 Johnson track. For single direction soft door operation, the 1060 must be used in combination with a 1125 Door Hanger. For bi-directional soft door operation two (2) 1060's are required.
The 1060SOFT Retrofit Kit is designed to quickly convert existing openings with Johnson 100 track to single direction soft-close door operation.
The 6320 Kit is compatible with our Assembled Wood Pocket frame, and our BP250N-01 track found in BP150 and PD150 hardware kits. Order two kits for each track if you want soft open and soft close.
ItemMax Dr
Wt Application Use With1060 200 1 Direction Johnson 1560, 1562. For 1500, 2610, 134F order one 1125 hanger per door.
1060SOFT 200 1 Direction Johnson 1500, 1560, 1562, 2610, 134F.
6320 150 1 Direction Wood Pocket Frames, Sets of BP150, PD150 for Track BP250N-01
Soft Close Mechanisms
Bypass Parts Description List1120 Hanger Ea. for (134F & 1530) 6.001121 Hanger Plate for 1120/1125 1.801125 Hanger Ea. 200 lb (134F&1560) 14.002030 Guide Post Each. 1.21”H 4.102034 1-3/4” Bypass Door guide 6.402035 1-3/8” Bypass Door guide 6.202054 Multi-Pass Pull per Set 10.802135 Bypass Guide 3/4” or 1-3/8” 1.602136 Carpet Riser 5/8” High 1.502155 Door Stop Mounts on door 1.402165 Track Stop 1166, 1138, 2200, 2200F 2.402216 Hanger ea. 1/16” offset (1166 - 2200) 1.402228 Hanger ea. 75lb (2200-2200F) 2.702238 Hanger ea. 3/8” offset (1166 - 2200) 1.402312 (old PD75) Hanger ea. V- track & 7/8” Wheel 6.90BP150-71 Floor Guide for 3/4” to 1-3/8” drs. 3.00BP150-73 Nylon Floor Guide, per pair 2.00BP 150N-HDW Bag 150 lb (2 pr hangers, guide) 41.00BP 250N-HDW Bag 250 lb (2 pr hangers, guide) 55.00BP250N-01-48 Track Each - 2 req’d per opg 13.00BP250N-01-60 Track Each - 2 req’d per opg 16.00BP250N-01-72 Track Each - 2 req’d per opg 20.00BP250N-01-96 Track Each - 2 req’d per opg 28.00BP250N-01-120 Track 10’ 34.00BP250N-01-144 Track 12’ 43.00BP250N-01-192 Track 16’ 71.00BP250-71 Floor Guide ADJ for 1-3/8” to 1-3/4” 8.00BP250-77 Center Stop for BP250-01 track. 1.70BP250-99 Wrench 0.50TR250 1-3/4” Spacer for BP250, ea. 2.00
BP150-71
BP150N-HDW BP250N-HDW
BP250-71
BP150-73
2054
2216 2228 2238
2312
2136
Bypass Parts
Priced on p a g e 2 7
1120 1125
BP250-77
2030
2034 2035
2135 2155
2165
BP250N-01
TR250BP250-99
26 7B store.bbwood.com 216-292-6555 [email protected]
Pocket Door Hardware (parts see page 28)
R.O. = door height + 4-1/2"
Sets include track, 1 pr. hangers, Pocket guide for 1-3/8" door. For 13/4" add PD250-72 page 28.
50 Lbs. Description List2850-96 For up to 4’0” Door 24.00
150 Lbs. Description ListKit.PD150-48 For 2’0” Door 27.00Kit.PD150-60 For 2’6” Door 30.00Kit.PD150-72 For 3’0” Door 34.00Kit.PD150-96 For 4’0” Door 48.00SC6320 Add Soft Close PD150 62.20
250 Lbs. Description ListKit.PD250-48 For 2’0” Door up to 250 lb 39.00Kit.PD250-60 For 2’6” Door up to 250 lb 42.00Kit.PD250-72 For 3’0” Door up to 250 lb 46.00Kit.PD250-96 For 4’0” Door up to 250 lb 60.00
400 Lbs. Description ListKit.PD400-48 For 2’0” Door up to 400 lb 128.00Kit.PD400-72 For 3’0” Door up to 400 lb 129.00Kit.PD400-96 For 4’0” Door up to 400 lb 146.00
Knock Down Pocket Kit2x4 Stud Height/Load List153068 6’8”/125 lbs 118.00153070 7’0”/200 lbs 153.00153080 8’0”/200 lbs 179.00153090 9’0”/200 lbs 257.001060SOFT Add Soft Close 1530 64.602x6 Stud Height / 200lb List15603068 6’8” 187.0015603070 7’0” 212.0015603080 8’0” 236.0015603090 9’0” 257.001060 Add Soft Close 1560 49.60
R.O. = door height + 4-1/2"
Sets include track, 1 pr. hangers, Pocket guide for 1-3/8" door. For 13/4" add PD250-72 page 28.
Min. door size for soft close is 24"
R.O. = door height + 4-1/2"
Sets include 1 peice of track, 1 pr. hangers, Pocket guide for 1-3/8" door. For 13/4" add PD250-72 page 28.
For 3/0 widths: marked to cut to smaller widths
Soft close min door width 24" (soft open & close 28")
For 1" to 1-3/8" doors . Add 1125 hangers for 200 lb on 6/8 height
R.O. = door height + 4-1/2"
Sets include track, 1 pr. hangers, Pocket guide for 1-3/8" door.
R.O. = door height + 4-1/2"
[email protected] 216-292-6555 store.bbwood.com 7B
Bypass Frame Kit 1562: see store.bbwood.comDesigned to carry 2 solid bypassing doors in a standard 2 x 6 wall or steel framed stud wall. The 1562 allows architects and designers to specify large room dividing openings with minimum wall obstruction for "clean and open" living spaces.
MAX DOOR WEIGHT: 200lbs. DOOR WIDTHS: 18", 24", 30", 36" MAX DOOR HEIGHT: 108" DOOR THICKNESS: 1-3/8" MIN WALL STRUCTURE THICKNESS: 5-1/2"
Soft close min door width 24" (soft open & close 28")
For 1" to 3" thick doors to 200 lbs
R.O. = door height + 5"
For 3/0 widths: marked to cut to smaller widths
Assembled Pocket Frames see store.bbwood.com
PD250-72 PD250-74 PD250-77
1120 1125
2802
Pocket Track & Hardware
PD150, PD250 Parts ListPD150 HDW Hanger Set (Pair) 150 lb 14.00PD250-71 Split Floor Guide - Pair 5.80PD250-72 Floor Guide 1-3/4” Doors 7.00PD250-74 Floor Guide 1-3/8” Doors 6.70PD250-77 Pocket Bumper: Set of 4 2.00PD250N-01-47 Track for 2/0 (44-3/4) 13.00PD250N-01-55 Track for 2/4 (52-3/4) 16.00PD250N-01-59 Track for 2/6 (56-3/4) 16.00PD250N-01-63 Track for 2/8 (60-3/4) 18.00PD250N-01-71 Track for 3/0 (68-3/4) 20.00PD250N-01-95 Track for 4/0 (92-3/4) 34.00PD250 HDW Hanger Set (Pair) 250 lb 26.00
Johnson including 1530, 1560, PD400 List10 Center guide post 1”H, Pair 5.50100-48 Track for 2/0: 1530, 1568 17.00100-60 Track for 2/6: 1530, 1568 21.00100-72 Track for 3/0: 1530, 1568 24.00100-96 Track for 4/0: 1530, 1568 33.001120 Hanger Ea 125lb for 100 track 6.001125 Hanger Ea 200lb for 100 track 14.001500PPK3 Replace part set for 1500/100PD 14.701550 Split Floor Guide - Pair 1.001555 Converging Dr Kit 1530, 1560 8.901575 Adaptor 1-3/4” Doors 1530 7.40200-48 Track for 2/0: PD400 43.00200-72 Track for 3/0: PD400 57.00200-96 Track for 4/0: PD400 75.002020 Hanger Ea. 400lb for 200 Track 36.502030 Guide Post Each. 1.21”H 4.002031 Guide Post Hvy Each. 1.21”H 5.002038 Floor Guide 1-3/8” Doors 4.302802 Hanger Each for 2850 pockets 4.00
1550 1555 1575
2020200
2030, 2031
10 100
PD250N-01PD150HDW, PD250HDW
2038
BP250-77 Track Stop pg 26
1500PPK3 not pictured: contains 2-1120, pair 1550, wrench, and Pocket Bumper.
28 7B store.bbwood.com 216-292-6555 [email protected]
B&B Wood Products inc.
Exterior Barn Door Hardware - for doors up to 400 lbs.
1-3/4" to 2-1/4"
1-1/2"to
2-1/4"
3-1/2"4-5/8"
Bolts furnished for doors up to 1-3/4" thick
*Close-Out
See page 30-35 for Interior Barn Door Hardware
12092 *9895 124 20896
301 301EC32LB 1-301 5-301
79
1L-301 65 673L-301
[email protected] 216-292-6555 store.bbwood.com 7B
Recommended spacing for brackets is 24"
Brackets for metal buildings - see store.bbwood.com
ITEM DESCRIPTION List
BD301-8 Galvzd Track 8’ 58.00
BD301-10 Galvzd Track 10’ 72.00
BD301-12 Galvzd Track 12’ 87.00
BD32LB Hangers (pair) 97.00
BD1-301 Single Side Bracket 9.00
BD1L-301 Joint Bracket - Splice bracket will join 2 pcs track 13.00
BD3-301 Ceiling Bracket 9.00
BD5-301 Double Side Bracket 31.00
BD301EC End Cap Only (fits inside Brackets sold separately) 2.00
BD65 Door Holder/stop - Max dr 2-1/4" 13.00
BD67 Stake Holder 7-3/4"w x 2-1/2"h 12.00
BD79 Guide -Adjust to 3-1/4" 49.00
BD92 Stay Roll - Adjust for 1-1/2" to 2-1/2" doors 26.00
BD95 Stay Roll - Adjusts for 1-1/4" to 2-5/8" doors 15.00
BD96 Stay Roll - Adjusts for 1" to 3-3/4" doors 34.00
*BD98 Stay Roll with 6" Lag - Close Out 7.00
BD120 Jamb Latch 7". Door thick 1-1/2" and greater 28.00
BD124 Sliding Latch Zinc. Accepts a padlock. 23.00
BD208 Door Pull - 7-7/8" Zinc 8.00
The 2610 is a commercial grade wall mounted sliding door hardware set designed for fast installation. Precision extruded aluminum box track features a built in fascia that hides the sliding hardware from view. Strong 3-wheel hangers are completely adjustable Bronze series has ball bearing wheels for doors up to 200 lbs. Zinc series for doors up to 125 lbs. Bronze features an extruded architectural grade dark bronze anodized track.
Wall Mount Sliding Door HardwareWall Mounted Sliding Door Hardware is ideally suited for applications where it is cost prohibitive or structurally impossible to install a pocket door. Installation is relatively straight forward and can be performed with minimal expertise. The track system can be covered and trimmed out by the installer to match other doors or millwork in the project. Note: See www.bbwood.com for installation instructions.
Single Wall Mount Sliding Door Converging Wall Mount Sliding Doors
Door Thickness: 1" to 1-3/4" Max Weight per Door: Zinc125 lb; Bronze 200 lbs.2610 SERIES:
Zinc: 1120 Hangers2682 End Caps2610
Kits: Track, hangers, guides, end caps & end stops
1155 End Stops 2030 Floor Guides
12 Wall Guide
BRZ: 1125 Hangers
2610 series Soft-Close see pg. 27 1060Soft
30 7B store.bbwood.com 216-292-6555 [email protected]
Minimum Door Thickness: 1-1/8" Maximum Door Weight: 300 lbs. per door.200WM SERIES:
The 200WM is a commercial grade wall mounted sliding door hardware system designed to carry heavy doors. The 200WM Hardware Set features heavy-duty extruded aluminum I-beam track, heavy-duty track mounting brackets and strong four wheel adjustable hang-ers with machine turned ball bearing wheels. 11-13 gauge zinc dichromate plated steel parts. Brackets (2006) should align with wall studs. End brackets within 8" of end of track. Fascia is an option in Bronze or Satin.
2030 Floor Guides
2006 2020 Hanger12 Wall Guide
2055 Stop200 Track
Kits Include: Track, hangers, guides, brackets and end stops
End caps for Bronze only
300 lbs: Min. Door Thick 1-1/8" List200WM72 One 3’0" Door 223.00200WM96 One 4’0" Door 256.00Fascia 8' 8' Bronze for 2610FB 88.00Fascia 16' 16' Bronze for 2610FB 145.00
125 lb Zinc Track; Door Thick 1" to 1-3/4" List2610F72 One 3’0" Door 81.002610F96 One 4’0" Door 103.00Upgrade 200 lb see 1125 in Pocket Hardware -
200 lb Bronze Track; Door Thick 1" to 1-3/4" List2610FB72 One 3’0" Door 142.002610FB96 One 4’0" Door 178.00
Parts List12 Guide Wall Mount Dr Guide 1-1/8" to 1-3/4" 2.00
Fascia
TM/FM: Round Rail
FM100 FM200 FM300
FSS: Flat Rail
Kit Includes:2 -Hangers in 304 Stainless Steel Rail & Brackets; End Stops
Max. loading weight: 220 lbs
1-5/16" to 1-3/8" Doors
[email protected] 216-292-6555 store.bbwood.com 7B
Stainless Steel Wall Mount Hardware - For 6' & 8' Openings
TM100 TM200 TM300
Kit Includes:2 - Strap in 304 Stainless Steel Rail, Brackets and Screws 1 - Left & Right Rail Stop 2 - Anti-jump Block 1 - Floor Center Guide
Item Stainless Steel Barn Door Hardware Kits: 6' & 8' ListFSS.6 Kit 6.6 ft. Flat Rail Stick Barn Door Hdwe Stain. Steel 214.00
FSS.8 Kit 8 ft. Flat Rail Stick Barn Door Hdwe Stain. Steel 261.00
TM100.6 Kit 6'6 Round Rail Top Mount Stick Barn Door Hdwe. 205.00
TM200.6 Kit 6'6 Round Rail Top Mount Dual Barn Door Hdwe 272.00
TM300.6 Kit 6'6 Round Rail Top Mount Spoke Barn Door Hdwe 334.00
FM100.6 Kit 6'6 Round Rail Strap Barn Door Hdwe Stain. Steel 256.00
FM200.6 Kit 6'6 Round Rail Dual Wheel Strap Barn Door Hdwe 394.00
FM300.6 Kit 6'6 Round Rail Triangle Strap Barn Door Hdwe 345.00
TM100.8 Kit 8' Round Rail Top Mount Barn Door Hdwe 419.00
TM200.8 Kit 8' Round Rail Top Mount Dual Barn Door Hdwe. 435.00
TM300.8 Kit 8' Round Rail Top Mount Spoke Barn Door Hdwe. 509.00
FM100.8 Kit 8' Round Rail Strap Barn Door Hdwe Stain. Steel 439.00
FM200.8 Kit 8' Round Rail Dual Wheel Strap Barn Door Hdwe 639.00
FM300.8 Kit 8' Round Rail Triangle Strap Barn Door Hdwe 567.00
Item Stainless Steel Components ListTM-FM.RAIL.6 6.6 ft. Round Rail, 4 Mounting Brackets, 2 End Caps 216.00
TM-FM.RAIL.8 8 ft. Round Rail, 5 Mounting Brackets, 2 End Caps 324.00
TM-FM.SPLICE Track Connector for TM and FM Series 18.00
TM.Strap.100 Hanger Ea. Only Top Mount Stick Deseign 128.00
TM.Strap.200 Hanger Ea. Only Top Mount Dual Wheel 354.00
TM.Strap.300 Hanger Ea. Only Top Mount Spoke Wheel 292.00
FM.Strap.100 Hanger Ea. Only Face Mount Stick Design 260.00
FM.Strap.200 Hanger Ea. Only Face Mount Dual Wheel 434.00
FM.Strap.300 Hanger Ea. Only Face Mount Triangle 308.00
CenterFloor.630 Stainless Steel Floor Guide for Wood Door 12.00
FSS.Strap.Stick Hanger only Ea. For FSS Design 170.00
FSS.RailStop.LH Rail End Stop Left for FSS Design 50.00
FSS.RailStop.RH Rail End Stop Right for FSS Design 50.00
FSS.TRACK.6 Track for FSS 6.6 ft. with 5 Mounting Brackets and Spacers 292.00
FSS.SPLICE Connector for FSS Stainless Steel Flat Track 12.00
1-1/4" to 2-5/8" Doors
32 7B store.bbwood.com 216-292-6555 [email protected]
Designer Flat Track Barn Door Hardware: 6'6"220 Lbs. for interior use with wood doors ranging from 1-3/8" to 1-3/4" thick.
Black, Chrome, White, Oil Rubbed Bronze, Satin Nickel, Antique Brass and
Satin Brass pictured on store.bbwood.com
Designer Flat Track: Accessories
MFS24 Soft-Close Black1 MFS24 will do a soft open and close on 1 track.
MFS19 Rail Connector, Black1 - Connector4 - Flat Head Screws 1/4-20 Thread
6' Kits For weights up to 220 lbs ListMFS3-6.622 Kit 6.6 ft. Hook Strap Wheel 2-3/4 Black 137.00MFS3-6.WHT Kit 6.6 ft. Hook Strap Wheel 2-3/4 White 182.00
MFS3-6.619 Kit 6.6 ft. Hook Strap Wheel 2-3/4 Sat. Nickel 232.00MFS3-6.609 Kit 6.6 ft. Hook Strap Wheel 2-3/4 Ant. Brass 169.00
MFS3-6.625 Kit 6.6 ft. Hook Strap Wheel 2-3/4 Chrome 296.00
MFS3-6.606 Kit 6.6 ft. Hook Strap Wheel 2-3/4 Satin Brass 424.00
MFS3-6.613 Kit 6.6 ft. Hook Strap Wheel 2-3/4 Satin ORB 169.00
MFS5-6.622 Kit 6.6 ft. Hook Strap Wheel 5" Black 177.00MFSTM-6 Kit 6.6 ft. Top Mount Wheel 2-3/4 Black (up to 198 lb) 90.00
8' Kits For weights up to 220 lbs ListMFS3-8.622 Kit 8 ft. Hook Strap Wheel 2-3/4 Black 276.00
MFS3-8.WHT Kit 8 ft. Hook Strap Wheel 2-3/4 White 279.00
MFS3-8.619 Kit 8 ft. Hook Strap Wheel 2-3/4 Sat. Nickel 335.00
MFS3-8.609 Kit 8 ft. Hook Strap Wheel 2-3/4 Ant. Brass 280.00
MFS3-8.625 Kit 8 ft. Hook Strap Wheel 2-3/4 Chrome 399.00
MFS3-8.606 Kit 8 ft. Hook Strap Wheel 2-3/4 Satin Brass 517.00
MFS3-8.613 Kit 8 ft. Hook Strap Wheel 2-3/4 Satin ORB 280.00
MFS5-8.622 Kit 8 ft. Hook Strap Wheel 5" Black 319.00
Parts Designer Parts ListCenterFloor.622 Floor Guide for Wood Doors-Plastic Black 2.00MFS.16L.622 Door Stopper Left, MFS Black 20.00
MFS.16R.622 Door Stopper Right, MFS Black 20.00
MFS.18.622 Rail Plastic Anti-jump, MFS Black 2.00
MFS.19.622 Rail Connector works with MFS Track, Black 7.00MFS.Track3-6.613 Track MFS3 6.6 ft. Oil Rubbed Bronze 137.00
MFS.Track3-6.622 Track MFS3 6.6 ft. Black 126.00
MFS.Track5-6.622 Track MFS5 6.6 ft. Black 154.00
MFS.Hook3.622 Hanger Only MFS3 Ea. Black 43.00
MFS.Hook5.622 Hanger Only MFS5 Ea. Black 71.00
MFS.TopMount.622 Hanger Only MFSTM Ea. Black 43.00MFS.23.619 By-pass Brckt Each. Sat Nickel. Ord 5 for 6'6 track 32.00
MFS.23.622 By-pass Bracket Each. Black. Ord 5 for 6'6 track 28.00MFS.24.622 Soft-close MFS (pair) (N/A w/Chrome). Black. 58.00
MFS23 Bypass BracketFor a 6' kit purchase 5 brackets and two MFS Kits
[email protected] 216-292-6555 store.bbwood.com 7B
Flat Track USA Barn Door Hardware - 4', 6' & 8'
The wheels are made up of high density PVC for a quieter and smoother rolling door. The rails and brackets are made out of sturdy extruded aluminum, making them light weight but strong. The aluminum has a powder-coated black finish, Rated for 250 lbs.
• Made in the USA• Powder coated Black components• 3” & 5” diameter PVC wheel• Kits include Aluminum rails,hangers, stops, guide, and all fasteners• Interior Use Only
Gap between the wall and the door =1-15/16” minus door thickness.
250 Lbs. for interior use with wood doors ranging from 1-3/8" to 1-3/4" thick.
RSR
RSB
RSD RSS
RTM
RSH
FT.SPLICE
4' Kits Rated for up to 250 lbs ListKit.RSD.4 Kit 4' with Dually Strap Black 375.00
Kit.RSS.4 Kit 4' with 3" Hook Strap Black 188.00Kit.RSB.4 Kit 4' with 5" Hook Strap Black 204.00Kit.RSH.4 Kit 4' Horse Shoe Strap Black 312.00
Kit.RSR.4 Kit 4' with Stick Strap Black 176.00Kit.RTM.4 Kit 4' with Top Mount Black 179.006' Kits - ListKit.RSD.6 Kit 6' with Dually Strap Black 363.00
Kit.RSS.6 Kit 6' with 3" Hook Strap Black 199.00Kit.RSB.6 Kit 6' with 5" Hook Strap Black 214.00Kit.RSH.6 Kit 6' Horse Shoe Strap Black 324.00
Kit.RSR.6 Kit 6' with Stick Strap Black 186.00Kit.RTM.6 Kit 6' with Top Mount Black 190.008' Kits - ListKit.RSD.8 Kit 8' with Dually Strap Black 558.00
Kit.RSS.8 Kit 8' with 3" Hook Strap Black 320.00Kit.RSB.8 Kit 8' with 5" Hook Strap Black 342.00Kit.RSH.8 Kit 8' Horse Shoe Strap Black 473.00
Kit.RSR.8 Kit 8' with Stick Strap Black 302.00Kit.RTM.8 Kit 8' with Top Mount Black 306.00
Parts - ListStrap.RSD Hanger Each Only Dually 211.00
Strap.RSS Hanger Each Only 3" Hook 80.00Strap.RSB Hanger Each Only 5" Hook 98.00Strap.RSH Hanger Each Only Horse Shoe 164.00
Strap.RSR Hanger Each Only Round Stick 70.00Strap.RTM Hanger Each Only Top Mount 72.00FT.Track..4 Flat Rail 4 ft Black USA 72.00FT.Track..6 Flat Rail 6 ft BlackUSA 90.00FT.Track..8 Flat Rail 8 ft Black USA 136.00FT.Splice Splice Kit for Flat Rail USA Black 18.00FT.R201 Bracket Flat Rail Bracket Kit Black 10.00
FT.R40 Stop Flat Rail Stop Kit Black 18.00
CenterFloor.622 Black Plastic Floor Guide 2.00
Specify Black, ORB or Satin Nickel
Satin Nickel
Satin Nickel
Specify Black, ORB or Satin Nickel
34 7B store.bbwood.com 216-292-6555 [email protected]
Round Rail Barn Hardware - for up to 250 lb. Doors
Includes: 2 Roller Straps; 1 Center Guide; 1 Left &1 Right Stop; Wall Brackets (every 16”); 2 Track Button End Stops; 1 Tap
Gap between the wall and the door: 2-1/2“ minus door thickness.
2.9”W x 6.8”HSquare Stick
2.75”W x 6.67”HRound Stick
4.12”W x 6.17”HHorse Shoe
3” W x 10.5”HSpade
2.5”W x 7.75”HHook
3.25”W x 11.75”HFleur-de-Lis
Splice Kit
Roller Center Guide: For doors with rough surfaces, Con-structed of heavy duty black polymer
Ball Track End Stop: 1-1/2"Priced per pair.
Bi-Parting Center Door Stop:
4.5”W x 5.5”HThree Point
Black, Oil Rubbed Bronze and Satin Nickel
Options
$27.00
$96.00
14.00 15.40 15.40
$8.80RT.DD402
RT.CenterRoll
RT.BALL
RT.SPLICE
4’ Kits Rated for 250 lbs for 1-1/4” to 2-1/4” Doors List
Black List ORB
List 619
Kit.RT4.Fleur 4’ Fleur-de-Lis Round Track Hammered 392.00 431.20 -
Kit.RT4.Hook 4’ Hook Round Track 264.00 290.40 290.40Kit.RT4.HS 4’ Horseshoe Round Track 276.00 303.60 303.60Kit.RT4.Round 4’ Round Stick Round Track 249.00 273.90 273.90Kit.RT4.Spade 4’ Spade Round Track Hammered 444.00 488.40 -Kit.RT4.Square 4’ Square Stick Round Track 252.00 277.20 277.20Kit.RT4.Three 4’ Three Point Round Track 294.00 323.40 323.40Kit.RT4.TM 4’ Top Mount Round Track 264.00 290.40 290.40
6’ Kits - List
Black List ORB
List 619
Kit.RT6.Fleur 6’ Fleur-de-Lis Round Track Hammered 435.00 478.50 -
Kit.RT6.Hook 6’ Hook Round Track 308.00 338.80 338.80Kit.RT6.HS 6’ Horseshoe Round Track 320.00 352.00 352.00Kit.RT6.Round 6’ Round Stick Round Track 293.00 322.30 322.30Kit.RT6.Spade 6’ Spade Round Track Hammered 488.00 536.80 -Kit.RT6.Square 6’ Square Stick Round Track 296.00 325.60 325.60Kit.RT6.Three 6’ Three Point Round Track 338.00 371.80 371.80Kit.RT6.TM 6’ Top Mount Round Track 308.00 338.80 338.80
8’ Kits - List
Black List ORB
List 619
Kit.RT8.Fleur 8’ Fleur-de-Lis Round Track Hammered 508.00 558.80 -
Kit.RT8.Hook 8’ Hook Round Track 372.00 409.20 409.20Kit.RT8.HS 8’ Horseshoe Round Track 384.00 422.40 422.40Kit.RT8.Round 8’ Round Stick Round Track 356.00 391.60 391.60Kit.RT8.Spade 8’ Spade Round Track Hammered 564.00 620.40 -Kit.RT8.Square 8’ Square Stick Round Track 359.00 394.90 394.90Kit.RT8.Three 8’ Three Point Round Track 404.00 444.40 444.40Kit.RT8.TM 8’ Top Mount Round Track 372.00 409.20 409.20
Top Mount
List Black List ORB List 619
Parts priced on store.bbwood.com
[email protected] 216-292-6555 store.bbwood.com 7B
Wall Mount Handles
Round Rail Bypass KitTo be used with Round Rail Rolling Door HardwareBlack, Satin Nickel or ORB FinishIncludes:5 Rail Brackets w/long screws5 Rail Brackets w/short screws4 Steel Door Stoppers1 Wall Mounted Guide1 Floor Mounted Guide2 Stop Slots
*For bypass application, 1 kit and 2 rolling door kits are required*
OAH: 11"OAW: 2-3/4"Proj.: 1-1/2"
OAH: 13"OAW: 3-1/2"Proj: 3"
OAH: 8-3/4"OAW: 1-5/8"Proj.: 1-1/4"
OAH: 8-1/2"OAW: 1-7/8"Proj.: 1-1/2"
OAH: 8-7/8"OAW: 1-7/8"Proj.: 1-1/2"
OAH: 8-5/8"OAW: 1-13/16"Proj.: 1-1/2"
P399HF910HF909HF908HF907HF906
OAH: 10"OAW: 1-7/8"Proj.: 1-1/2"
HF905OAH 8-5/8"OAW 12-1/2"Proj 2-1/4"
HF904OAH 8-5/8"OAW 1-3/4"Proj 1-5/8"
HF903OAH 6-3/4"OAW 1-7/8"Proj 2"
HF902OAH 8-7/8"OAW 1-7/8"Proj 1-5/8"
HF901
HF series are hand forged. Available in Black, Satin Nickel and Oil Rubbed Bronze.
RT.Bypass
ItemHF901HF902HF903HF904HF905HF906HF907HF908HF909HF910P399
List86.00
86.00
90.00
168.00
59.00
42.00
39.00
59.00
38.00
35.00
60.00
299.00 328.90 328.90
List Black List ORB List 619
36 7B store.bbwood.com 216-292-6555 [email protected]
V1342 Screen & Storm Closers List PriceBlack Door Opens about 85 degrees $27.00Aluminum Door Opens about 85 degrees $27.00
CLOSERS, SPRINGS, CHAINSThis door closer is designed for wood or metal screen and storm doors Adjusts easily by rotating the tube to increase or de-crease door closing power. Door will swing open ap-proximately 85º. Offers smooth, no-bounce operation.
V1342
Full Mortise – Mortise one leaf into the butt edge of door and the other leaf mortise into the edge of the door frame.
Half Surface – Attach one hinge leaf to the door face and mor-tise the other leaf into the edge of the door frame.
Full Surface – Attach one hinge leaf to the door face and the other to the door frame front surface
Offset – Attach one hinge leaf to surface of the door and attach the other leaf to the surface of the door frame.
Hinge Types:
2960- 2-3/4" x 2-3/4"
SPRINGFull Surface Non-Adjust-
able
Strap Hinges - See page 10
V76: 16" Long - Safe working load 22 lbs
V129 - 3" x 2-1/2"
Half Surface, Full Surface
or Offset
45S: Black or ZincSN123 Specifications:
SN123
Page 21 for pricing
Max Dr Width 36" Max Dr Weight 150 lb
Silver, Black, White, Brown
Screen/Storm Hinges - Price per Pair
3035 - 3-1/2"W x 3"H
Half Surface,
.157 thick
Solid Brass
V513 3" x 2-1/2"
Full Mortise
Solid Brass
968S Black Non-Adjust 6" Close-Out966S Black Adjustable 7"
Gate Hinges - Per Pair
Finish V129 List V513 List 3035 List 2960 List 966S List 968S List 45S List V76 ListDull Brass 14.00 - - 15.00 - - - -Bright Brass - 40.00 66.00 - - - - -Lifetime Brass - 58.00 84.00 - - - - -Ant Brass - 49.00 73.00 - - - - -Oil Rub Brz - 49.00 73.00 - - - - -Satin Nickel - 49.00 73.00 - - - - -Pewter - 49.00 73.00 - - - - -Black 14.00 49.00 73.00 14.00 41.00 26.00 7.00 -Brite Chrome - 49.00 73.00 - - - - -Sat Chrome - 49.00 73.00 - - - - -Galvanized 28.00 - - - - - - -Zinc 12.00 - - 15.00 - - 7.00 7.00
Chart on top of page for pricing.
Chart on top of page for pricing.
Chart on top of page for pricing.
[email protected] 216-292-6555 store.bbwood.com 7B
For wood screen/storm doors 7/8" to 1-1/8"1159/980 has 1-3/4" Backset; 1100 rim lock does not require an edge bore
11001157
Dummy Knob
Screen & Storm Door Hardware - see Section -5 for complete sets
Pulls
Mortise pocket: 9/16"W x 2-1/8"H x 2-1/4"DPlate dimension 1-1/4"W x 6"H; 1-1/2" backset.
Exterior & Interior SpecsClearance: 3⁄4”Projection: 15⁄8”Lever Length: 25⁄8”Knob Diameter: 1-11⁄16”Door Thickness: 1” to 1-1⁄2”
1190 1191
P254-7/8" Long; 1-5/32" Proj.
C110S Length 7-1/2"
Finish1159 List 1157 List 1100 List 1190/1191
List 1165 List C103S List
C110S List P25 List
Bright Brass 55.00 19.00 34.00 177.00 - - - 3.00Ant Brass 60.00 - 53.00 177.00 - - - -Oil Rub Bronze 60.00 - 60.00 177.00 - - - -Satin Nickel 60.00 - 56.00 177.00 - - - -Pewter 42.00 - - 177.00 - - - -Black 57.00 19.00 38.00 177.00 35.00 28.00 9.00 4.00Pol. Chrome 60.00 - 34.00 177.00 - - - -Satin Chrome 55.00 - - 177.00 - - - -Alumimum - - - 177.00 - - - 3.00
C103S Length 8"
Item may vary from picture.
Hammered Finish
11658-1/2" x 1-5/8"
Proj.1-1/2"
C103S Thumb Latch - Black- For either right or left-hand applications- Designed to latch in or out-swinging gates and doors up to 3" thick- Equipped with easy-to-operate locking feature1165 Thumb Latch - Black- For either right or left-hand applications- Rim Latch sets mount on your door and release the latch by pressing on the thumbplate.
Gate Latches
1159
V21AGate and post must be flush; latch assembly is mounted on gate for out-swing gates and on post for in-swing gates. Priced on store.bbwood.com
38 7B store.bbwood.com 216-292-6555 [email protected]
Shutter Hinges & Pintels
For shutters hung flush with casing. Pintel permits easy hanging and removal of shutters. Hinge measures 4-1/4” vertical and 5” horizontal. Pintel plate 3-1/8” x 1-1/8”.Specify AK1 for 1-1/4” offset, 2-1/2” reveal: Use on frame construction.Specify AK2 for 2-1/4” offset 4-1/2” reveal: Use on brick construction.
Each set contains 2 pair of hinges.
“L” Hinge Style
Butt Hinge Style
RK1: 3x4 Maximum Throw 1-1/2"RK2: 3x5 Maximum Throw 2-1/2"RK3: 3x6 Maximum Throw 3-1/2"
Hinge is reversible with loose pin. It is made with curved offset to throw shutter clear of window. Hinge width should be equal to twice the depth of the reveal. Sold in pairs (2 pairs required per window)
For Dummy Hinges see page 10
Stainless steel strap hinge with adjustable pintels. Hing-es are reversible. Sold EACH (4 required per window)
Strap Hinge
AKF: Flush, 13-3/8” strap lengthAKG: 1 ¼” offset, 13” Strap lengthAKH: 2 ¼” offset, 12 ¼” Strap length
Adjustable pintel for a wide variety of shutter applications. Pintel and plate are stainless steel. Measurements from center of pintel.
AKE: Backplate 1 ½” x 4 ½”; Pintel 4-7/8” x 3/8” x 1-9/16” H
Adjustable Pintel
Shutter HoldbacksShutter Dog
Aluminum with 4” stainless steel lag. Sold in Pairs. AK4 7” x 2-3/8”
Acorn Catch
9/16" x 1-1/4" long The Bullet is solid brass .Catch is stainless steel. AKZ 9/16” x 1-1/4”
Shutter Bolts
RL9BP: Overall Bolt Length: 6-5/8”Back Plate: 6-7/8” x 1-11/16”Surface Strike: 3-1/4” x 1-11/16”Screws are Stainless Steel
RLABP: Overall Bolt Length: 6" Back Plate: 2-1/4" x 1-1/4" Stainless Steel Screws included.
Item List Package
AK1 71.00 set of 2 pr
AK2 78.00 set of 2 pr
AK3 39.00 set of 2 pr
AK4 39.00 pair
AKA 93.00 set of 2 pr
AKB 93.00 set of 2 pr
AKE 30.00 each
AKF 75.00 each
AKG 75.00 each
AKH 75.00 each
AKM 93.00 set
AKZ 23.00 each
RK1 57.00 pair
RK2 60.00 pair
RK3 62.00 pair
RL9 59.00 each
RLA 59.00 each
Connecticut Shutter Hinge:AK3: 4” flatAKA: 5-1/8” w/2-3/16" offsetAKM: 5-1/8” w/1-1/4” offset AKB: 6-7/8” flat
1 set contains two pair of hinges
[email protected] 216-292-6555 store.bbwood.com 7B
7/8” 7/8”
1-1/2”
3/4”
H6155 Wrap AroundFor 3/4" panels
Use with rabbeted Panels
3/4”
1”
7/16”
7/16” 7/16”
1-1/2”
H7 Butt Hinge
For 3/4" panelsMortise (Swaged)
H5 Extension HingeFor 3/4" panels
Mortise (Swaged)
3/4”
1-1/2”
2-3/8”
1-1/2”
H298: 4-Panel Set
2 pr Brass WrapAround hinges 2 pr Brass Flat-back hinges 2 Porcelain Knobs, 1 Brass Hook
5/8”
1-3/8”
1-1/2”
H6144 Flat Back for 3/4"
H6148 Butt Hinge for 3/4"Mortise (Swaged)
Shutter Knobs
Cabinet & Shutter Hardware Priced on store.bbwood.com
15 lb. per panel capacity
For 3/4” to 1-1/8” shutters. Panels 6” to 18” wide and 80” high.
Finished Opening is Door Height +1-5/8”
1-1/32”
5/8”
Mounts directly to head jamb or cabinet. Available
up to 192”.
For multi-folding units order an additional hanger
for each door.
B170A Alum. Track
B1742 Hanger
B1740BS Hardware Set
Hardware set includes enough hardware for 1 pair of shutters. Includes one 1742 hanger; 1710 pivot lock; 1701 Top pivot;1707 Bottom
pivot, pair of hinges; 1713 snubber; 1741 jamb bracket and instructions.
SB30: 1” SB31: 1-3/8”
Polished Brass, Antique Brass, Oil Rub Bronze, Satin Nickel, Pewter, Satin & Polished Chrome
Shutter Bar
H16 Butt Hinge
Mortise (Swaged)For 3/4" panels
H22 Wrap Around
Mortise (Swaged)For 1-1/8" panels
H1255 Butt 2-1/2" sq
Mortise (Swaged)For 1-1/8" panels
Magnetic Catch
MC5100
D326A33-1/8” x 1” x 9/16”
Bifold Hardware
K218 Concave Knob1-3/4” Diam.
Chrome- Antique Brass
K6115 PorcelainIncludes 2 knobs 5/8" with Satin Brass Hook
Closeout
7/8” Diameter Bright Chrome
K626 Knob
Support Braces-6658-6659-6661-6663
Support Braces-6658-6659-6661-6663
Joiner SupportBraces-6635-6637
Joiner Plate-6667,6687, 6689
Back Clips
Rod Spacer Cap-6651
F-Chanel6697
AngleWallBracket6646
Corner Shelf (19”x19”)
66236753
Wall Bracket-6621, 6725
66236753
662367536623
6753
66206743
Wire Shelving
Item Shelf & Rod 12’ Ctn. List Each1110-1212 12” Shelf & Rod 6 53.301110-1612 16” Shelf & Rod 6 75.60- Open Slide 12’ List Each1710-1212 12” Open Slide Shelf 6 82.201710-1612 16” Open Slide Shelf 4 109.70- Storage (Linen) 12’ List Each1210-1212 12” Linen Shelf 6 52.901210-1612 16” Linen Shelf 6 69.301210-2012 20” Linen Shelf 6 92.00- Tight Mesh 12’ List Each1510-1212 12” Tight Mesh Shelf 6 68.401510-1612 16” Tight Mesh Shelf 6 91.401510-2012 20” Tight Mesh Shelf 6 117.50
Corner ShelvesItem Corner Shelves Ctn. List Each1110-1219 12” Shelf & Rod Corner 10 51.701110-1619 16” Shelf & Rod Corner -subject to stock 10 35.701710-1219 12” Open Slide Corner 10 52.001710-1619 16” Open Slide Corner 10 59.30
40 7B store.bbwood.com 216-292-6555 [email protected]
Shelf & Rod
Open (Free) Slide
Storage (Linen)
Tight Mesh
Wall Bracket-6621, 6725
Item Supports Ctn. List Each1435-6658 9” Tight-Mesh and 10” Shelf&Rod 30 2.801430-6659 12” Shelves, 16” Shelf & Rod & 16” Open-Slide 100 2.391435-6661 16” Linen and Tight-Mesh and as a ctr support for 20”
Tight-Mesh30 3.00
1465-6663 20” Standard and Tight-Mesh Storage Shelves 30 3.101430-6635 12” Joiner Support Brace (requires 2-6677) - subject to stock 100 2.201435-6637 16” Joiner Support Brace (requires 2-6677) - subject to stock 10 2.70
Joiner Clamps Ctn. List Each1430-6677 Joiner Clamp : Use 2 per Brace; Order 6687 & 6689 screw & nut 100 0.801430-6687 #8-32 Pan Head Phillips Machine Screw 1000 0.071430-6689 #8-32 Nut 1000 0.071435-6676 Open-Slide Joiner Clip, nuts, bolts, WasteSaver Joiners 10 sets 1.60
Back Clips, Side Wall Brackets
: Install support brace at 42”, for heavy loads at 24”Support Braces
Joiner Suppport Braces requires: Joiner Clamp (use 2 per brace) #6677 #8-32 PanHead Phillips Machine Screw #6687 #8-32 Nut #6689
6658665966616663
6635, 6637
Joiner Plates
6676
6677 (brace not included)
Support PoleItem Support Pole & Hardware Per Ctn. List Each1430-6665 Adjustable Pole Clip Plastic w/ screw 100 1.001430-6670 Snap-in Pole Clip 100 1.611430-6671 Base Cap 100 0.301430-6673 Vertical support pole 84-3/4” 24 12.30
6725 6621 6624 6646
66456743 6620 66236753
66526675
6697
6693 6694 6668
Item End Cap, Corner Bracket, Shoe Support Per Ctn. List Each1430-6675 Metal Corner Bracket 100 1.901430-6681 #8x1-1/2” Truss Phillips Screw use with support braces 1000 0.151435-6688 #8X1-1/2” Phillips Screw for sidewall brk 250 0.151435-6652 Double End Cap (replaces 6651) 200 0.371430-6697 F-Channel; 6’ Plastic Sidewall support for angled walls. 12 40.401430-6699 Extra Small End Cap for Crosswires 1000 0.051430-6693 Medium End Cap-for all styles except tight mesh (old 6683,6684) 1000 0.05
1430-6694 Large End Cap-for all styles except tight mesh (old 6685,6686) 1000 0.051430-6668 Shoe Shelf Support - Used with linen & tight mesh 100 1.60
Miscellaneous Hardware
-Basic Installation Hardware Per
Ctn. List Each
1430-6743 Pin Driven Back Clip (install every 11”) 3000 0.351430-6620 Versa Back Clip with Tri-Loc II 2000 0.361430-6753 Pin Driven Wall Anchor 3000 0.301430-6623 Tri Loc II Anchor 1000 0.401430-6725 Pin Driven Wall Bracket 500 1.251430-6621 Wall Bracket with Tri-LocII 300 1.381430-6624 Wall Bracket - No anchors 300 0.601435-6646 Angled Side Wall Bracket (rotates to 45 degrees) 10 4.801435-6645 1/4” Strap Back Clip 100 0.40
[email protected] 216-292-6555 store.bbwood.com 7B
Item Shelf & Rod Support Ctn List4700 White: 10-1/4 to 10-3/4 20 5.00
Heavy Duty Adjustable Shelf & Rod Support
Will support shelf up to 12” wide and rod up to 1-1/2” diameter.
Item Adjustable Rods Ctn List4500 18-30 Expands 18”-30” 10 7.004500 30-48 Expands 30”-48” 10 9.004500 48-72 Expands 48”-72” 10 14.004500 72-96 Expands 72”-96” 10 18.004500 72-120 Expands 72”-120” 10 22.004500 96-150 Expands 96”-150” 10 28.004500
1” Diameter Chrome Closet Rod - Adjustable
1” Diameter Chrome Closet Rod
4700
Ivory Enamel
Item Closet Rods List7913-1524 2’ Chrome Rod 7.007913-1536 3’ Chrome Rod 11.007913-1548 4’ Chrome Rod 14.007913-1572 6’ Chrome Rod 21.007913-1596 8’ Chrome Rod 27.007913-1510 Rod Stops (pair) 7.00Rod Stop Rod Flange
Chrome Rod 1" Diameter
store.bbwood.com for pricing
42 7B store.bbwood.com 216-292-6555 [email protected]
Window Hardware
Double Hung Spiral tubular balances (stock) and Vinyl compression balances (special order). See store.bbwood.com for details.
Bulb and wool pile weatherstrips are available for window stiles and check rails.
B&B Wood Products inc.
List for Sash Locks & Lifts
[email protected] 216-292-6555 store.bbwood.com 7B
Sash Lock
Sash Lift
Strike: 5/8"x 2-9/16"
Window Hardware
- Sash Locks Sash Locks Solid Brass Sash Lifts Sash Lifts
Solid Brass
- 07A List 07B List 026A List 026B ListBright Brass 3.40 21.00 3.00 11.00Antique Brass 5.10 - 4.00 -
Aged Bronze - 26.00 4.00 14.00Satin Nickel 4.30 30.00 4.00 14.00Pewter - 30.00 - 17.00Black - 27.00 5.00 -
Bright Chrome - 29.00 4.00 11.00Sat Chrome - 29.00 - 15.00Galvanized - - - -
07A - Aluminum07B - Solid Brass
- 066A List 066B List 80B List 82 ListBright Brass 8.00 35.00 71.00 10.00Antique Brass - 41.00 - -Oil Rub Bronze 8.00 - 71.00 -Satin Nickel - 43.00 71.00 11.00Pewter - - - -Black - - 71.00 -Bright Chrome 8.00 41.00 - -Sat Chrome - 41.00 - -
Base: 15/16"x 2-9/16"
• Designed low to the sash for superior strength and greater resistance to breakage.• Vertical & horizontal camming action for snug, non-rattling fit• Heavy gauge springs provide long-wearing actionMeets ANSI/BHMA A156.16
#026A - Aluminum#026B - Solid Brass
Projection: 1-1/16"Base: 1-1/8"x4"
Meets ANSI/BHMA A156.16
Bold Pricing Stock. Store.bbwood.com for stock status
82 Transom Chain
Design pictured may vary
80 Transom Catch
• Independent latch action; transom can be closed by pushing directly on ring.• Latch bolt can be easily reversed by removing back plate. • Conforms to design requirements of ANSI/BHMA A156.16
1-1/4" x 2-1/4"
7.50
10.10
V83
V80 Hanger
Sold Per Pair Galvanized
Per Pair
Per Set of 4
Screen/Storm Hardware
12" Long
7/8" x 1-5/8"
066A - Aluminum
• For use on windows to provide weather-tight fastening and security.• Also ideal for securing louvered doors and small doors. • Meets ANSI/BHMA A156.16.
066B - Solid Brass
066A includes mortise and rim strike. 066B includes rim strike.
Projection 1-3/8"
066 Casement Latch
B&B Wood Products inc.
$2 Catalog © 2020 B&B Wood Products, Inc All rights reserved
Distributed by:
Price subject to change without notice.