S4 Door and Window Sensor based on BLE5.0 technology, it can be installed on doors, windows and even desk drawers. By detecting the opening and closing of doors and windows, the S4 can wirelessly notify to Avior of arrivals and departures. The S4 consists of a main body, mounted to the door or window frame, and a magnet to be mounted to the door or window. FEATURES Door/window status data Tamper alarm Replaceable coin battery Maximum 100 meter advertising range Easy to install sensor and magnet Bluetooth® EPL Certification CE Regulations FCC Regulation CERTIFICATION ¡ ¡ ¡ . . . . . CONTRIVE S.R.L. Via Enrico Fermi 18 I-24040 SUISIO (Bergamo) Tel. +39 (0)35 4948236 Fax +39 (0)35 4933759 B2900_S4.EN / 0521 www.contrive.mobi USER GUIDE Model 2900.S4.1A Wireless Protocol Bluetooth 5.0 Tranmission power 0dBm Transmission Range 100 m Temperature -20 to 60 °C Humidity 0 to 95% Battery type 1 x CR2032 Battery life up to 13 months Main Body Size 55 x 26 x 13 mm Magnet Size 39 x 13 x 11 mm Color White Material ABS Weight 27g When the device detects the door is opened or sensor is tampered, it will automatically send status data to Avior. NON-CONDENSING PROGRAMMING GUIDE www.contrive.mobi/avior CONFIGURATION SOFTWARE www.contrive.mobi/E/aviorsuite.php CLOUD CONTROL PANEL www.avior.webadmin.mobi To use the sensor you will have to proceed with the pairing by appropriately configuringAvior. For Avior configuration you can connect the device to a PC and run the AviorSuite software or access the cloud administration interface or integrated web server (if available). On the configuration page, select one of the 8 door sensors (identified from A to F) and enter the MAC address you find on the device. It is also possible to assign a name that identifies the sensor. Once the sensor is paired you will be able to detect the opening and closing of the door, the tampering of the sensor, the loss of connection and the battery charge level. PRODUCT SPECIFICATION PRODUCT SPECIFICATION PAIRING BLE DOOR / WINDOW SENSOR BLE DOOR / WINDOW SENSOR avior S4
Transcript
S4 Door and Window Sensor based on BLE5.0 technology, it can beinstalled on doors, windows and even desk drawers. By detecting theopening and closing of doors and windows, the S4 can wirelesslynotify toAvior of arrivals and departures.The S4 consists of a main body, mounted to the door or window frame,and a magnet to be mounted to the door or window.
FEATURES
Door/window status dataTamper alarmReplaceable coin batteryMaximum 100 meter advertising rangeEasy to install sensor and magnet
To use the sensor you will have to proceed with the pairing byappropriately configuringAvior.ForAvior configuration you can connect the device to a PC and run theAviorSuite software or access the cloud administration interface orintegrated web server (if available).
On the configuration page, select one of the 8 door sensors (identifiedfromAto F) and enter the MAC address you find on the device. It is alsopossible to assign a name that identifies the sensor.Once the sensor is paired you will be able to detect the opening andclosing of the door, the tampering of the sensor, the loss of connectionand the battery charge level.
Push up the Battery Rear Cover and open it, take out the Button Celland replace it. Cover it up again to finish battery replacement.
The device has no power switch. Remove the [2] topower on the door/window sensor.Tear off the 3M protective film on the Main Body Back.Paste the [A] to the door or window frame, and [B]to the door or window, respectively.When pasting, make sure the surfaces are clean and dry.Main Body and Magnet must be aligned when the door or window isclosedWhen installation is finished, make sure the [4] isclosed (blue light will not flash), otherwise the installation isunsuccessful.
Insulation Sheet
Main Body Magnet
Tamper Switch
DECLARATION OF CONFORMITY
Contrive S.r.l.Via Fermi 18 I-24040 Suisio
declares that the DoC is issued under our sole responsibility
and belongs to the following product :
is in conformity with the relevant Union legislation
S4BLUETOOTH LOW ENERGY DOOR / WINDOW SENSOR
the following standards and technical specifications have been applied :
STANDARD ISSUE DATE
STATES INTENDED FOR USE : ALL EU AND EFTA MEMBERSMEMBER STATES WITH RESTRICTIVE USE : NONE
THE TECHNICAL DOCUMENTATION AS REQUIRED BY THE CONFORMITY ASSESSMENTPROCEDURE IS KEPT AT THE COMPANY MAIN OFFICE
CFR (CODE OF FEDERAL REGULATIONS) TITLE 47 TELECOMMUNICATIONS
THIS DEVICE COMPLIES WITH FCC RULES
Output power listed is the maximum conducted output power. device must operated to provide aseparation distance of at least 20 cm from all persons and must not transmit simultaneously with any otherantenna or transmitter, except in accordance woth FCC multi-transmitter product procedures. Users andinstallers must be provided with antenna installation instructions and transmitter operating conditions forsafety RF exposure compliance.
Radio Equipment Directive 2014/53/EU
Suisio, Italy May 21, 2021
SAFETYEN 62368-1 2014 A/V IT COMEN 62368-A11 2017EN 62479 2010 HEALTHEMCEN 301 489-1 2019 v2.2.3 RADIO EQUIPMENTEN 301 489-17 2020 v3.2.4 RADIO EQUIPMENTRADIO SPECTRUMEN 300 328 2019 v2.2.2 WIFI BLUETOOTH
�
�
�
FCC IDENTIFIER: 2ABU6-S4Part 15C Radio Frequency Devices - Intentional radiators
FREQUENCY RANGE: 2402.0 - 2480.0 MHzOUTPUT POWER: 0,003 W
EQUIPMENT CLASS : Digital transmission system
GRANT NOTES
1
2
3
45B
A
A
B
1
2
3
4
5
Main body
Magnet
Led indicator
Insulation sheet
Coin battery
Tamper switch
Rear cover with adhesive
BLINK BLUEDoor status changedTamper detected
Low batteryBLINK RED
CAUTION
�
�
.
.
Avoid strong magnetic interference
Use the product indoor and avoid water damage
Do not install the sensor in a sealed metal space.
Turn off the tamper alarm function before replacing the battery.
