Date post: | 16-Apr-2017 |
Category: |
Engineering |
Upload: | upender-rawat |
View: | 667 times |
Download: | 21 times |
Suspension Design by Rajeev Mokashi 2
Acknowledgements
Explanation of “Automotive Suspension” www.HowStuffWorks.com
SAEINDIA presentation “Suspension design” by Mr Ravindra Deshmukh, Dy GM (R & D), Mahindra & Mahindra, Nashik. 2007
“Suspension Design” presentation by Mr Rob Shanahan, 15-11-2005
“Automotive Suspension design”. Ref: http://en.wikipedia.org/wiki/Automotive_suspension_design
“Vehicle Dynamics – Theory & Application” by Mr Reza N Jazar
Suspension Design by Rajeev Mokashi 3
Introduction
What is an Automotive Suspension?An Automotive Suspension is the system of parts that give a vehicle the ability to maneuver.It is a 3 Dimensional Four Bar Linkage
What does a suspension do?“The job of a car suspension is to maximize the friction between the tires and the road surface, to provide steering stability with good handling”
Ref: www.HowStuffWorks.com
Suspension Design by Rajeev Mokashi 4
Process of Suspension Design
Selecting vehicle level targetsSelecting system architecture – type of suspension etc.Choosing location of ‘Hard points’.Selecting rates of the bushings.Analysing the loads in suspension.Designing Spring ratesDesigning Shock absorber characteristics.Designing structure of each component – Strong, stiff, Light, easy to manufacture and Cheap.Analysing Vehicle Dynamics of the resulting design
Suspension Design by Rajeev Mokashi 5
Vehicle level targets (main)
Ride heights at various states of loadRide frequenciesRoll stiffness (Deg / g of lateral acceleration)Distribution of load – front to rearJounce travel (Bump / Compression)Rebound travel (Droop / Extension)CamberCasterToe In / Toe Out
Suspension Design by Rajeev Mokashi 7
Desirables for Vehicle level targets
Stiffness – Design for maximum torsional stiffness and least weight. This is checked by holding rear shock absorber points & applying torque at front shock absorber points.Provide large suspension travels – typically 250 ~ 300 mm. For typical ATV, ratio of Jounce travel to Rebound travel is 2:1.Provide sufficient ground clearance – more than 200 mm.Use maximum track / overall width allowed. Place wheels at farthest corners.Design to provide tunable features – to adjust Camber, Caster, Toe In, damping forces in shock absorber, spring force on assembly etc.Keep aggregates like Fuel tank, Powertrain etc. as low as possible.
Suspension Design by Rajeev Mokashi 8
Suspension Architecture
Double Wishbone (Equal or Unequal arm)
• Lightest weight• Lowest unsprung mass• Greatest adjustability for roll center height, camber, caster etc.
McPherson Strut / semi –strut
• Compact suspension• Less adjustability
Recommendation: Double wishbone – unequal arm
Suspension Design by Rajeev Mokashi 10
Hard point location
Hard points determine Static settings:Toe (normally Toe In 3 ~ 5 mm)Camber (normally 0.5° ~ 2°)Caster (normally 2° ~ 4°)Roll center height at design load (vis-à-vis CG)caster trailKingpin inclination (normally 7° ~ 8°)Scrub radiusSpring / Shock absorber motion ratios
Hard points also affect Handling of the vehicle in dynamic state.
Suspension Design by Rajeev Mokashi 11
Roll center
Roll center moves as suspension travels.Goal of any suspension designer is to minimize Roll Center Migration.
Distance from roll center to CG is key to decide roll couple. Lower distance the better.
Suspension Design by Rajeev Mokashi 12
Design of suspension components
Wishbone – Control arms etc.Keep calculations simple. Draw Free Body Diagrams for loads on wishbones.Design for Stiffness Strength follows.Create clean Drawings /Sketches for fabrication. Keep Shapes simple.Calculate stresses for single events – 5 g impact etc. Ensure maximum stress below Yield Stress with good factor of safety.
Wishbone pivots / bushesUse rubber bushings or solid bushings. Ensure wishbones move freely and do not rub against attachments / brackets etc.
Rubber bushes, if readily available, are preferred.Compliances may be worked out during tuning
Suspension Design by Rajeev Mokashi 13
Design of suspension components
Coil springs / shock absorbersCoil springs over shock absorber designs are easy for tuning, byproviding screwed type of spring seats on shock absorber body.Use wheel frequency of 100 ~ 125 cpm for designing spring stiffness. For passenger cars, this frequency is 60 ~ 80 cpm. Choose shock absorber length longer than required – by 10 mm or more, so that it does not bottom out with full bump (2.5 g).Check that coil spring does not become solid at full bump load.
Suspension Design by Rajeev Mokashi 14
Effect of Suspension geometry on handling of vehicle
Twitchy in back, tires wear on outer edge. More oversteer, more forgiving limit
More positive camber in rear wheels
More oversteer, car feels twitchy in back, tyres wear out on the inside edge
Less oversteer, more rear grip / limit -3 degrees
More negative camber on rear wheels
Poor braking, car is road crown sensitive, twitchy, tires wear out on outer edge.
More understeer, can make the tyres last longer
More positive camber on front wheels
Poor braking, car is road crown sensitive, twitchy, tyres wear out on the inside edge
Less understeer /limit-3 degrees
More negative camber on front wheels
Understeers, then oversteers as car bottoms out with a jolting ride.
Less oversteerRear spring rate decrease
Too much oversteer, hop in corners, twitchy.
More oversteerRear spring rate increase
Oversteers. then understeers as car bottoms excessively with jolting ride
Less understeerFront spring rate decrease
Terminal understeer, front of car hops in corners.
More understeerFront Spring rate increase
Symptom of too much adjustmentAffect on vehicle handling, limit adjustmentSuspension adjustment
Suspension Design by Rajeev Mokashi 15
Effect of Suspension geometry on handling of vehicle
Not usableNegative front caster
Can increase understeer, increases steering efforts.
Helps both stability, steady state cornering and turn in. Limit 6 degrees positive.
Positive front caster
Not good for street driving, causes lift throttle oversteer, car makes violent side to side rocking motions in rear.
Helps car rotate, useful on tight low speed courses and slalom events (limit 3 mm total toe out)
Toe Out rear
Twitchy under braking, car is road crown sensitive, car wanders on straight road.
Car turns in well, good in FWD cars. ( limit 6 mm toe out)
Toe Out front
Weird slow rocking movement in back, feels slow but unstable.
Less likely to oversteer when throttle is lifted
Toe In rear
Car has slow twitchiness under braking, feels odd, wears out outer edge of tyres
Car is stable while going straight. Turn in is average.
Toe In front
Symptom of too much adjustmentAffect on vehicle handling, limit adjustment
Suspension adjustment