Baler BOA Impress M75-45F-A-5-S-1.6, press power 71,2 tons, yoc 2015, drive power 45 kW, incl. chain belt conveyor and personal protection system It is a complete pressing plant for paper / cardboard recycling, consisting of: Conveyor system, baling press incl. maintenance platforms, wire pull stations, bale slider and personal protection system. The plant will be in operation until approx. November 2020 and will then be replaced by a new plant. The sale is ex location. The organisation and execution of dismantling, loading and clean-swept handover of the hall is the responsibility of the buyer. An offer for outsourcing can be made on request. Technical data baler Manufacturer Type M75-45F-A-5-S-1.6 Year of construction 2015 Hours of operation 8,200 hours (stand 03.07.2020) Press power main press 71,2 kN Specific press capacity 9 kg/cm² Operating pressure 280 bar Cylinder stroke 2,200 mm Feed channel 1,620 x 1,000 mm Capacity per cycle time 2,4 m³ Theoretic cycle time 23 seconds Theoretic throughput rate 400 m³/hour Bale size 1,100 x 720 mm, length variably adjustable up to 1,400 mm Driving motor 45 kW Tying system 5-fold vertical, fully automatic Throughput rate at a bulk weight of 30 kg/cbm approx. 8 tons/hour bulk weight of 50 kg/cbm approx. 14 tons/hour bulk weight of 100 kg/cbm approx. 20 tons/hour bulk weight of 150 kg/cbm approx. 26 tons/hour Bale weight up to 600 kg, depends on material Volume hydraulic oil tank 1,000 l
Transcript
Baler BOA Impress M75-45F-A-5-S-1.6, press power 71,2 tons, yoc 2015, drivepower 45 kW, incl. chain belt conveyor and personal protection system
It is a complete pressing plant for paper / cardboard recycling, consisting of:
Conveyor system, baling press incl. maintenance platforms, wire pull stations, bale slider and personal protection system.The plant will be in operation until approx. November 2020 and will then be replaced by a new plant. The sale is ex location.The organisation and execution of dismantling, loading and clean-swept handover of the hall is the responsibility of thebuyer. An offer for outsourcing can be made on request.
Technical data balerManufacturerType M75-45F-A-5-S-1.6Year of construction 2015Hours of operation 8,200 hours (stand 03.07.2020)Press power main press 71,2 kNSpecific press capacity 9 kg/cm²Operating pressure 280 barCylinder stroke 2,200 mmFeed channel 1,620 x 1,000 mmCapacity per cycle time 2,4 m³Theoretic cycle time 23 secondsTheoretic throughput rate 400 m³/hourBale size 1,100 x 720 mm, length variably adjustable up to 1,400 mmDriving motor 45 kWTying system 5-fold vertical, fully automaticThroughput rate at abulk weight of 30 kg/cbm approx. 8 tons/hourbulk weight of 50 kg/cbm approx. 14 tons/hourbulk weight of 100 kg/cbm approx. 20 tons/hourbulk weight of 150 kg/cbm approx. 26 tons/hourBale weight up to 600 kg, depends on materialVolume hydraulic oil tank 1,000 l
Baler BOA Impress M75-45F-A-5-S-1.6, press power 71,2 tons, yoc 2015, drivepower 45 kW, incl. chain belt conveyor and personal protection system
SPS controller (manuf., type) Siemens S7 300Operating panel (manuf., type) Siemens Multi Touch PanelBaler hight built up with hopper 7,100 mmMachine weight baler approx. 32 tonsNoise level &85 dB (A) Technical data of the chain belt conveyor, feeding to the balerManufacturer BOATyp 1700 KTH HSB 32° 4,000 x 7,300 x 1,500 mmYear of construction 2015Drive power 3 kWLenght feeding belt 4,000 mmLenght elevator belt 7.300 mmLength gooseneck with feed funnel 1.500 mmEffective width 1,620 mmGrade 32° Condition of the baler and conveyor belt:The whole facility is in a very well maintained condition and will be in operation until approx.October/November 2020. After that the machines are available for dismantling and loading by thebuyer. If required, the plant can also be dismantled and loaded by external companies on site. Scope of delivery:- Chain belt conveyor BOA, type 1700 KTH HSB 32°, for upper floor feeding of the baler
- Baler BOA M75-45F-A-5-S-1.6
- Special accessories press, wire tensioning device for the lower wires
- Access ladder with maintenance platform at the feed chute of the press
- Access stairs with maintenance platform at the needle and tying unit of the press
- 4 wire drawing stations with wire deflection and 10 wire roll stands (without wire)
- Bale slider
- Personal protection system BOREMA PSS i-BOR 12 Comments:The documentation (Manual, CE, electr./hydr.-drawings), are completely available. Inspections arepossible after agreement. We will not assume liability for the given technical data and possibleerrors.
- Page 2 of 7 -
Baler BOA Impress M75-45F-A-5-S-1.6, press power 71,2 tons, yoc 2015, drivepower 45 kW, incl. chain belt conveyor and personal protection system
Feeding the cardboard boxes by means of a forklift, with a rotatingfork, on an upper floor chain belt conveyor.
Conveying of the cardboard boxes via an ascending conveyor withgooseneck and BOREMA personnel safety system PSS i-BOR 17,directly into the press.
Baler BOA Impress M75-45F-A-5-S-1.6, year of construction 2015,pressing force 71,2 kN, drive power 45 kW, PLC Siemens S7 300.
The press is controlled via a separately in front of the baler placedcontrol cabinet with Siemens Touch Panel.
The scope of delivery includes 4 wire drawing stations with wiredeflection and 10 wire roll stands (without wire).
- Page 3 of 7 -
Baler BOA Impress M75-45F-A-5-S-1.6, press power 71,2 tons, yoc 2015, drivepower 45 kW, incl. chain belt conveyor and personal protection system
Overview of the complete line, the PET press line on the far leftside of the picture is also for sale separately.
Also included in the scope of delivery is an access ladder withmaintenance platform at the feed chute of the press.
Hydraulic power unit with 45 kW drive motor, 1,000 l hydraulic oiltank and with oil cooler.
- Page 4 of 7 -
Baler BOA Impress M75-45F-A-5-S-1.6, press power 71,2 tons, yoc 2015, drivepower 45 kW, incl. chain belt conveyor and personal protection system
The scope of supply also includes an access staircase withmaintenance platform on the needle and tying unit of the press.
- Page 5 of 7 -
Baler BOA Impress M75-45F-A-5-S-1.6, press power 71,2 tons, yoc 2015, drivepower 45 kW, incl. chain belt conveyor and personal protection system
Special equipment, laterally swivelling tying system, for easycleaning and maintenance.
The bottom of the press channel is equipped with replaceable,wear-resistant HARDOX steel plates.
5-fold vertical binding with 4 material retaining clamps. Serrated counter knife plate, segmented exchangeable, for easycutting of the cardboard.
Press ram with segmented blade set, individually exchangeable. The press floor is equipped with wear-resistant HARDOX steelplates, individually replaceable.
- Page 6 of 7 -
Baler BOA Impress M75-45F-A-5-S-1.6, press power 71,2 tons, yoc 2015, drivepower 45 kW, incl. chain belt conveyor and personal protection system
Pre-press flap in good condition.
Switch cabinet, four-part, with key transfer system, air conditioning,Siemens S7 300 control system and separate switch cabinet (leftside) for the BOREMA personal protection system PSS i-BOR 17.
Separate control cabinet with Siemens Multi Touch Panel,mounted approx. 5 m centrally in front of the press for a betteroverview.
Overview of the cardboard box pressing line, consisting of the maincomponents chain belt conveyor, PSS i-BOR personal protectionsystem and baler.
