NIPPON
EMT IMC RSC
WHITE CONDUITZINC-COATED STEEL
FOR ELECTRICAL WIRING
TIS 770-2533
BANGKOK, 2018TAM PATRA
Bangkok
NIPPONTIS 770-2533
DISTRIBUTION BY :NIPPON PIPE (THAILAND) CO.,LTD.154 MOO 5, PANTAINORASINGHA DISTRICT,SAMUTSAKHON CITY, SAMUTSAKHON PROVINCE,THAILAND, 74000
MANUFACTURE BY :THAI STEEL ELECTRIC INDUSTRY LTD.,PART.14 SAMAEDUM 17, SAMAEDUM SUB-DISTRICT, BANGKHUNTIEN DISTRICT, BANGKOK,THAILAND, 10150
WWW.NIPPONCONDUIT.COM
PLEASE CONTACT :
NIPPON
TIS 770-2533
NIPPON is a company, with one goal : to deliverthe highest quality product and service solution
that contribute to our customer’s success.
We are committed to exceeding the quality requirement and expectations of our customersand continual improvement of all aspects of
our business. This goal will be achieved throughour focus on these quality objectives :
> Meeting and exceeding customer requirements and product standards.> Providing the highest level of product quality and service
> Producing and delivering product on-time> Producing at the lowest possible cost
TONY WONGDIRECTOR,
NIPPON PIPE (THAILAND) CO.,LTD.Stated 2016,
“QUALITY, You can trust” Galvanized steel for electrical wiring system
Over 20 years, we are rich experienced
NIPPONCONTENTS
1. COMPANY PROFILE
2. MATERIAL SUBMISSION LIST
3. SPECIFICATION, COMPARISION, CATALOGUE
4. CERTIFICATION
5. REFERRENCE
COMPANY NAME : NIPPON PIPE(THAILAND) CO.,LTD.
FOUNDER : MR.TANINTHORN WONGCHAROENCHAICHANA
ESTRABLISHED : 2016, JANUARY 4
REGISTERED CAPITAL : THB 1,000,000
ADDRESS : 154 MOO 5, PANTAINORASINGHA DISTRICT,
SAMUTSAKHON CITY, SAMUTSAKHON PROVINCE
THAILAND, 74000
NO. OF EMPLOYEE : 10 PEOPLE (APPROX.)
SCOPE OF PRODUCT : ELECTRICAL RACEWAY
EMT : ELECTRO ZINC PLATTING
IMC : ELECTRO ZINC PLATTING
RSC : HOT DIP ZINC GALVANIZE
CONTACT INFORMATION
TELEPHONE : (+66) 34 448 999
FAX : (+66) 34 448 909
EMAIL : [email protected]
WEBSITE : WWW.NIPPONCONDUIT.COM
GROUP OF COMPANY
TANINTHORN METAL WORK CO.,LTD.
THAI STEEL ELECTRIC INDUSTRY LTD.,PART.
NIPPON PIPE (THAILAND) CO.,LTD.
DYNAMIC (THAILAND) CO.,LTD.
P.S.R.ELECTRIC SUPPLY CO.,LTD.
PRODUCT : ELECTRICAL STEEL CONDUIT
BRAND : NIPPON
MATERIAL : STEEL, ZINC GALVANIZE
ORIGIN : THAILAND
TYPE TRADE SIZE STANDARD
EMT 1/2” - 2” TIS 770-2533, ANSI C80.3, UL797
IMC 1/2” - 4” TIS 770-2533, ANSI C80.6, UL1242
RSC 1/2” - 6” TIS 770-2533, ANSI C80.1, UL6
TIS 770-2533
EZ Pull
AN EASY PULLINGELECTRICAL WIRING SOLUTION With internal enamel coating, EZ Pull offers exceptional wire-pulling performance. A lightweight, smooth-pull wiring solution, easy to bend, yet tough for all locations that comply with the UL-797, including dry,wet, exposed, concealed or hazardous locations.
½”
¾”
1¼”
1”
1½”
2”
15
20
25
32
40
50
LENGTH WALL THICKNESS* WEIGHT*
In. mm. Ft.In.In. In. Ibs.mm. mm. mm. mm. Kgs.
TRADE SIZE OUTSIDE DIAMETER INSIDE DIAMETER*
0.706
0.922
1.163
1.510
1.740
2.197
17.93
23.42
29.54
38.35
44.20
55.80
0.622
0.824
1.049
1.380
1.610
2.067
15.80
20.93
26.64
35.05
40.89
52.50
10
10
10
10
10
10
3050
3050
3050
3050
3050
3050
1.07
1.25
1.45
1.65
1.65
1.65
0.042
0.049
0.057
0.065
0.065
0.065
2.85
4.35
6.40
9.50
11.00
14.00
1.272
1.305
2.856
4.242
4.911
6.249
* For information only, not a UL 797 requirement.Applicable tolerances: Length: 10' (3.05 m) ± ¼" (± 6.4 mm.), Wall Thickness: ± 10% Outside diameter: ½” through 2”: ± 0.005" (16 through 53: ± 0.13 mm.), 2 ½: ± 0.010" (63: ± 0.25 mm.),3: ± 0.015" (78: ± 0.38 mm.), 3 ½ and 4: ± 0.020" (91 and 103: ± 0.5 mm.)
3”
2½”
3½”
65
80
90
2.875
3.500
4.000
73.03
88.90
101.60
2.731
3.356
3.834
69.37
85.24
97.38
10
10
10
3050
3050
3050
1.83
1.83
2.11
0.072
0.072
0.083
21.62
26.34
34.97
9.806
11.947
15.862
4” 100 4.500 114.30 4.334 110.08 10 3050 2.110.083 39.35 17.848
| Electrical Metallic Tubing (EMT):
HOT-DIP GALVANISED AVAILABLE
Lightweight, Easy to install
Mild Steel, Easy to precise bend
Additional clear coating,corrosion resistance and
more brigher exterior surface
Smooth enamel coating,faster wire pulling performanceand free from defects injurious
to conductors
Original Zinc Electro-PlattingBrighter smoothly zinc coated surface whichluxury gentle, zinc coated thickness are over20 µm.
Interior Enamel spray coatingThe inside diameter is sprayed with a proprie-tary coating for corrosion resistance and easywire pulling.
STANDARD:ANSI C80.3UL 797TIS 770-2533
GALVANIZATION:Type I : Electro-Zinc PlattingType II : Hot-Dip GalvanizedType III : Pre-Zinc Galvanized
STRONG WAY
A LIGHTER-WEIGHT SOLUTIONTO RIGID STEEL CONDUIT IMC Conduit weighs 30% less than RSC conduit but provides a highlevel of protection for conductors and cables installed in areas potentially exposed to served physical damage. It also offers corrosion protection for installation in dry, wet,exposed, concealed or hazardous locations that comply with the UL-1242
| Intermediate Metal Conduit (IMC):
LENGTH WALL THICKNESS* WEIGHT
In. mm. Ft.In.In. In. Ibs.mm. mm. mm. mm. Kgs.
TRADE SIZE OUTSIDE DIAMETER* INSIDE DIAMETER**
10
10
10
10
10
10
3030
3030
3025
3025
3025
3025
1.97
2.10
2.35
2.41
2.54
2.67
0.078
0.083
0.093
0.095
0.100
0.105
10
10
10
3010
3010
3005
3.81
3.81
3.81
0.150
0.150
0.150
10 3005 3.810.150
½”
¾”
1”
1¼”
1½”
2”
2½”
3”
3½”
4”
15
20
25
32
40
50
65
80
90
100
0.825
1.029
1.290
1.638
1.883
2.360
2.857
3.476
3.971
4.466
20.70
26.14
32.77
41.59
47.82
59.93
72.57
88.29
100.86
113.44
0.660
0.869
1.105
1.448
1.683
2.150
2.557
3.176
3.671
4.166
16.76
22.07
28.07
36.77
42.74
54.60
64.95
80.67
93.24
105.82
2.54
34.6
4.99
6.43
7.91
10.52
18.62
22.90
26.30
29.61
5.59
7.62
11.00
14.17
17.43
23.19
41.05
50.48
57.98
65.27
* Figures are the average of the maximum and minimum dimensions as given in UL-1242.** Calculated from nominal outside diameter and nominal wall thickness. Applicable tolerances: Length: 10' (3.05 m) ± ¼" (± 6.4 mm.), Outside diameter: ½” through 1”: ± 0.015" (16 through 25: ± 0.38 mm.), 1¼” through 4” : ± 0.025" (32 through 100: ± 0.64 mm.), Wall thickness: ½” through 2”: 0.010” ± (16 through 50: ±0.2 mm.), 2½” through 4”: 0.012” ± (65 through 100: ±0.3 mm.)Steel IMC is manufactured to produce a 10' (3.05 m) length of conduit when a standard coupling is attached.
HOT-DIP GALVANISED AVAILABLE
In-House CNC Threading
Double end threading
Additional clear coating,corrosion resistance and
more brigher exterior surface
Smooth enamel coating,faster wire pulling performanceand free from defects injurious
to conductors
Original Zinc Electro-PlattingBrighter smoothly zinc coated surface whichluxury gentle, zinc coated thickness are over20 µm.
Interior Enamel spray coatingThe inside diameter is sprayed with a proprie-tary coating for corrosion resistance and easywire pulling.
STANDARD:ANSI C80.6UL 1242TIS 770-2533
GALVANIZATION:Type I : Electro-Zinc PlattingType II : Hot-Dip GalvanizedType III : Pre-Zinc Galvanized
THE ULTIMATE ELECTRICALWIRE AND CABLE PROTECTIONThe best wire and cable protection, it’s thick wall against physical damage, and hot-dip galvanized both exterior and interiorprovided the durability to withstand the most corrosive environments for installation in dry, wet, exposed, concealed or hazardous locations that comply with the UL-6
HEAVY DUTY | Rigid Steel Conduit (RSC):
Post Hot-Dip GalvanizedIn-House CNC Threading
Double end threading
Additional clear coating,corrosion resistance and
more brigher exterior surface
Smooth enamel coating,faster wire pulling performanceand free from defects injurious
to conductors
Original Hot-Dip GalvanizedBoth exterior and interior with hot-dip galva-nized.The best corrosion protection.
Interior Enamel spray coatingThe inside diameter is sprayed with a proprie-tary coating for corrosion resistance and easywire pulling.
STANDARD:ANSI C80.1UL 6TIS 770-2533
GALVANIZATION:Type II : Hot-Dip Galvanized
LENGTH WALL THICKNESS* WEIGHT
In. mm. Ft.In.In. In. Ibs.mm. mm. mm. mm. Kgs.
TRADE SIZE OUTSIDE DIAMETER* INSIDE DIAMETER**
½”
¾”
1”
1¼”
1½”
2”
2½”
3”
3½”
4”
5”
6”
10
10
10
10
10
10
10
10
10
10
10
10
21.34
26.67
33.40
42.16
48.26
60.33
73.03
88.90
101.60
114.30
141.30
168.28
15
20
25
32
40
50
65
80
90
100
125
150
16.05
21.23
27.00
35.41
41.25
52.91
63.22
78.49
90.68
102.87
128.85
154.76
3030
3030
3025
3025
3025
3025
3010
3010
3005
3005
3000
3000
2.64
2.72
3.20
3.38
3.51
3.71
4.90
5.21
5.46
5.72
6.22
6.76
3.585
4.763
6.940
9.117
11.295
15.060
23.905
30.963
37.694
44.104
59.585
79.167
0.840
1.050
1.315
1.660
1.900
2.375
2.875
3.500
4.000
4.500
5.563
6.625
0.632
0.836
1.063
1.394
1.624
2.083
2.489
3.090
3.570
4.050
5.073
6.093
* Figures are the average of the maximum and minimum dimensions as given in UL-6.** Calculated from nominal outside diameter and nominal wall thickness. Applicable tolerances: Length: 10' (3.05 m) ± ¼" (± 6.4 mm.), Outside diameter: ½” through 2”: ± 0.015" (16 through 50: ± 0.38 mm.), 2 ½” through 6” : ± 0.025" (65 through 150: ± 0.64 mm.), Wall thickness: -12.5%Steel RSC is manufactured to produce a 10' (3.05 m) length of conduit when a standard coupling is attached.
0.103
0.107
0.125
0.133
0.138
0.146
0.192
0.205
0.214
0.225
0.244
0.266
14.90
10.50
15.30
20.09
24.90
33.20
52.70
68.26
83.10
97.23
131.36
174.53
In. mm. In.In. mm. mm.
TRADE SIZE OUTSIDE DIAMETER LENGTH
Effective (L2)Overall (L
4) per inch
THREAD
In. mm.
PITCH DIAMETER (E0)
½”
¾”
1”
1¼”
1½”
2”
2½”
3”
3½”
4”
5”
6”
15
20
25
32
40
50
65
80
90
100
125
150
IMC COUPLINGS, ALSO HOT-DIP RSC COUPLING
IN-HOUSE THREADINGFIT TO CONDUIT
CROSS SECTION DRAWING
In-House CNC Threading
Additional clear coating,corrosion resistance and
more brigher exterior surface
TYPE:IMCRSC
GALVANIZATION:Type I : Electro-PlattingType II : Hot-Dip Galvanized
COUPLING
CONDUITL
2
L4
E0
25.70
31.80
38.70
47.50
54.70
67.30
82.60
98.30
111.10
123.80
152.40
182.90
19.26
24.58
30.83
39.55
45.62
57.63
69.08
84.85
97.47
110.09
136.90
163.70
41.30
41.70
50.00
51.60
52.40
54.00
81.00
84.10
86.50
89.30
100.00
108.00
19.80
20.10
24.90
25.70
26.20
26.90
39.90
42.40
42.70
43.90
46.70
49.50
13.50
14.00
17.30
18.00
18.30
19.30
29.00
30.50
31.80
33.00
35.80
38.400
14
14
11½
11½
11½
11½
8
8
8
8
8
8
1.011
1.251
1.523
1.870
2.153
2.649
3.251
3.870
4.374
4.874
6.000
7.200
0.758
0.967
1.213
1.557
1.796
2.268
2.719
3.340
3.837
4.334
5.389
6.444
1.625
1.641
1.968
2.031
2.062
2.125
3.188
3.311
3.405
3.515
3.937
4.251
IN-HOUSE BEND RIGHT ANGLE ํOur professional people, tooling and equipment are experience to delivery superior products, every customerand everytime without an accident.
ELBOW
Any Bend Angleํ 03 ,ํ 54 ,ํ 09
Precise Angle
Faster Insatllation
TYPE:EMT IMCRSC
GALVANIZATION:Type I : Electro-Zinc PlattingType II : Hot-Dip GalvanizedType II : Pre-Zinc Galvanized
LS
LS
R0
90 ํ
BRAND : NIPPON
PRODUCT : EMT, IMC, RSC
SPECIFICATION
1. GENARAL REQUIREMENT AS FOLLOW TIS 770-2533 STANDARD
2. CORROSION PROTECTION EMT : ELECTRO ZINC PLATTING, > 25 µm
INSIDER ENAMEL COATED
PRE-ZINC GALVANISED > 16 µm
IMC : ELECTROC ZINC PLATTING, > 30 µm
INSIDER ENAMEL COATED
PRE-ZINC GALVANISED > 16 µm
RSC : HOT DIP ZINC GALVANIZE, > 80 µm
INSIDER ENAMEL COATED
3. LENGTH AS FOLLOW TIS 770-2533 STANDARD
4. SIZE EMT : 1/2” - 4 ”
IMC : 1/2” - 6”
RSC : 1/2” - 6”
NIPPON
COMMERCIALSuvarnabhumi International Airport, SamutprakarnDonmueng International Airport, BangkokSiam Paragon, BangkokSiam Discovery, BangkokMBK Center, BangkokSummer Hill, BangkokAIS Building Sathorn, Bangkok
RESIDENCEA Space ME Rattanathibet, Nonthaburi
INDUSTRIALHonda, RayongThai Michelin, Rayong
GOVERNMENTGovernment Center, Cheangwattana, BangkokKlongteoy Port, Bangkok
INFRASTRUCTURE33 Highway, Sakaeo12 Highway, Tak35 Thonburi - Pakto Highway, Bangkok BTS, BangkokMRT, BangkokNakhon-In - Rama V Tunnel, NonthaburiNonthaburi Bridge 1, NonthaburiRama IX Bridge, BangkokDonmueng Tollway, BangkokThai-German Bridge, BangkokThai-Belguim Bridge, Bangkok