EQUIPMENT LIST
Bar Bender and Steel Fixer(CON/Q0203)
1.
Hammer
Bar tying hook
Bending lever, 12mm, 16mm, 20mm
Gauge measure (SWG)
Hack saw blade with frame
Spirit level
Plumb bob
Measuring tape
Rebar cutting machine
Rebar shearing machine
Rebar bending machine
Lifting appliances (wheel and rope, shackles, sling, belts)
Fire Extinguisher
Safety helmets
Rubber gloves
Safety shoes
Overalls
Reflective Jackets
x4
x4
x4
x4
x4
x4
x4
x4
x4
x4
x4
x4
x4
x1
x30
x1
x2
x1
x1
x1
x1
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
Cup lock scaffold (Including all the components)
Chisel
Rebar tying machine
JOB ROLE OVERVIEW
Bar Bender and Steel Fixer(CON/Q0203)
1.0
18 years
The job holder is responsible for carrying out cutting and bending of
reinforcement steel bar using hand and power tools along with
fabrication and placing of reinforcement steel bar as per drawing requirement
For Non trained worker : 5 years site experience in same occupation and
for Trained worker : 2 years site experience as a certified Assistant Bar Bender
& steel fixer
Normal literacy of reading, writing and understanding
4
Preferably 5th standard
N.A
6. The Assessor shall check the final outcome of the practices while evaluating
the steps performed to achieve the final outcome.
10. Minimum duration of Assessment of each QP shall be of 4hrs/trainee.
9. In case of successfully passing only certain number of NOS's, the trainee is
eligible to take subsequent assessment on the balance NOS's to pass the
Qualification Pack within the specified timeframe set by SSC.
7. The trainee shall be provided with a chance to repeat the test to correct his
procedures in case of improper performance, with a deduction of marks for
each iteration.
1. Criteria for assessment for each Qualification Pack will be created by the
Sector Skill Council. Each Performance Criteria (PC) will be assigned marks
proportional to its importance in NOS. SSC will also lay down proportion of
marks for Theory and Skills Practical for each PC.
3. Individual assessment agencies will create unique question papers for
knowledge/theory part for assessment of candidates as per assessment
criteria given below
4. Individual assessment agencies will create unique evaluations for skill practical
for every student at each examination/training center based on assessment
criteria.
2. The assessment for the knowledge part will be based on knowledge bank of
questions created by Assessment Bodies subject to approval by SSC
5. The passing percentage for each QP will be 70%. To pass the Qualification
Pack, every trainee should score a minimum of 70% individually in each NOS.
8. After the certain number of iteration as decided by SSC the trainee is marked
as fail, scoring zero marks for the procedure for the practical activity.
Assessment Guidelines Applicable National Occupational Standards (NOS)
Role Description
Version
Minimum Job Entry Age
Experience
Training
(Suggested but not mandatory)
NSQF Level
Minimum Educational Qualifications
Maximum Educational Qualifications
6. CON/N9001: Work according to personal health, safety and
environment protocol at construction site
3. CON/N0206: Prepare, fabricate, place and fix reinforcement
for RCC structures
4. CON/N8001: Work effectively in a team to deliver desired
results at the workplace
5. CON/N8002: Plan and organize work to meet expected
outcomes
2. CON/N0205: Use hand and power tools for cutting and
bending of reinforcement
1. CON/N0204: Read and understand routine drawings /
sketches and Bar Bending Schedule
CAREER MAP FOR
BAR BENDING AND FIXING
Supervisor Structure
Foreman Reinforcement
Helper Bar Bender and
Steel Fixer
Bar Bender and Steel Fixer
Bar Bending and Fixing
Assistant Bar Bender and
Steel Fixer
TRACKS
EN
TRY L
EVEL
MID
DLE
LEVEL
SUPERVIS
ORY L
EVEL
Reinforcement Fitter
