Date post: | 06-Apr-2018 |
Category: |
Documents |
Upload: | mazhar-talaat |
View: | 236 times |
Download: | 0 times |
of 20
8/2/2019 Barnett Quad Avi
1/20
8/2/2019 Barnett Quad Avi
2/20
Congratulations, you are the proud owner o
the fnest Production crossbow in the world!
Please ollow all saety, assembly and trouble shooting
instructions contained in this manual. It is extremely important
to read and ollow the instructions beore attempting to useyour crossbow. Serious injuries to yoursel or others, damage to
your crossbow, or poor perormance rom your crossbow could
result rom ailure to thoroughly read and understand these
instructions. I any part o this manual is unclear to you, contact
the Sales Department at 800-237-4507. Ater assembly o your
crossbow, please keep your manual or uture reerence.
For the Quad AVi, Barnett highly recommends using a 22Carbon or Aluminum arrow with hal moon nock weighing
at least 450 total grains including a 125-grain practice tip
or broadhead. Depending on your state regulations, we
recommend using mechanical broadheads, which result in a
more consistent ight pattern.
Manual Contents
Specications 3
Parts Checklist 3
Saety Guidelines 4
Crossbow Breakdown 5
Parts Picture 5
Assembly 6-8
Crossbow Operation 8-11
Troubleshooting 12-13Care and Maintenance 14
Warranty 16
Warranty Registration Back Cover
2
8/2/2019 Barnett Quad Avi
3/20
Specications
Feet per Second 345Power Stroke 15.5
Draw Weight 150 lbs
Physical Weight 7 lbs
Width 26.75
Length 37
String Length 39 5/8
Number o Strands 22
String Stock Number 16012
Beore beginning to assemble your crossbow, take a moment to
organize these parts and ensure you have everything you need.
I you are missing any o the below parts, contact the Barnett
Sales Department at 1-800-237-4507.
Parts List
1* Front Sight Bracket
2* Sight Pins
2* Front Sight Bracket Screws
1* Rear Peep Sight
2 Button Head Screws, Acorn Nuts
1 Lock Washers & Diameter or Foot stirrup
1 Socket Cap Screw or Prod Housing
1 Lock Washer or Prod Housing
1 ea Hex Keys: , 3/16, 5/32 & 2mm
1 Lubewax
* ITEMS ARE NOT INCLUDED WHEN BOW ISPURCHASED AS A PACKAGE WITH SCOPE.
3
8/2/2019 Barnett Quad Avi
4/20
Saety GuidelinesBarnett Quad AVicrossbows are equipped with an automatic
saety, which engages every time the crossbow is cocked. The
saety must be released beore each shot. This, as with any othermechanical device, does not guarantee total saety, as no saety
device is a substitute or common sense and sae handling. The
crossbow trigger is only to be pulled when the saety is in re
position and NEVER when it is in the sae position or anywhere
between sae and re. Do not attempt to alter or modiy the
saety or the trigger mechanism. When the trigger is pulled beore
the saety is released, the saety may not release. To correct this,push the trigger pull orward, then release the saety catch.
The ollowing rules should be ollowed at all times:
EXTREME CAUTION SHOULD BE USED AT ALL TIMES WHEN
HANDLING A CROSSBOW. FAILURE TO FOLLOW THESE RULES
COULD RESULT IN SERIOUS INJURY OR DEATH.
Always keep your ngers below the ight track and out o the
path o cables and strings when ring the crossbow. Never dry-re the crossbow (shooting without an arrow or too
light o an arrow). Dry ring will void the warrantyand can
result in damage to the limb assembly and possibly cause
personal injury.
Never re the crossbow until you are sure o your target.
Always use an adequate target and backstop when target
shooting.
Always use suitable crossbow arrows, such as Barnetts 22
Carbon Arrows with hal moon nocks made by BARNETT or
the Quad AVi. Arrows o improper stifness or mass weight may
damage the limb and cable assembly, voiding the warrantyand
possibly cause personal injury.
Always inspect the crossbow and arrows beore ring. Bent or
damaged arrows are not sae to re and should be discarded
or repaired.
4
8/2/2019 Barnett Quad Avi
5/20
Crossbow Breakdown
1. Stock
2. Cheek Piece
3. Cam
4. Limbs
5. Quiver (Not included i bow only is purchased)
6. Arrows (Not included i bow only is purchased)
7. 4 X 32 Scope (Not included i bow only or kit is purchased)
8. Scope Mount
9. String
10. Cables
11. Front Sight Assembly (Not Shown. Not included i bow
package with scope is purchased)
12. AVi Limb Retainer, Bezel, and Limb Bolt13. Foot Stirrup
14. Rear Peep Sight (Not Shown. Not included i bow package
with scope is purchased)
1
2
8
79
104
13
12
6
5
3
5
8/2/2019 Barnett Quad Avi
6/20
Assembly Guide
Attaching Prod Housing to Stock
Place the string on top o the ight track while sliding cables inthe long U-shaped channel. See Figure 1
Push bow limb assembly gently until it engages with stock.
Secure the bow limb assembly with the 5/16-18 X 2-1/4 socket
cap head bolt and lock washer. Tighten with hex key. See
Figure 2
Fig 1 Fig 2
Attaching Foot Stirrup Assembly
Align the rst hole on the oot stirrup over the rst hole on the
prod housing. Insert the -20 Button Head Cap Screw through
the oot stirrup and prod housing. Attach lock washer and
acorn nut.
Insert the second -20 Button Head Cap Screw through the
third hole o the oot stirrup and through one o two diameter nylon washer, then through the second hole o the
prod housing, through the
second nylon washer.
Attach lock washer and
acorn nut. Tighten with 5/32
hex key. See Figure 3
**Please note: Front sightis not included when a
crossbow package with
scope is purchased. Fig 36
8/2/2019 Barnett Quad Avi
7/20
Mounting the Front Sight
Fig 4
Align the holes o the ront sight
bracket with the holes on the
prod housing and attach rmlyusing the screws and washers
given in the hardware kit. See
Figure 4
Insert the rst sight pin through
the bracket with the slotted
screw ush inside the bracket
and tighten down the barreland washer on the outside o
the bracket. Install the second
pin in the same manner acing
rst pin. See Figure 5
**Please note: Peep sight is not
included when a crossbow
package with scope ispurchased.Fig 5
Mounting the Rear Peep Sight
Slide the rear peep sight onto
the attached dovetail with
setscrew acing the ront othe bow.
Tighten setscrew when the
peep is in the proper eye relie
position with the hex key
provided. See Figure 6Fig 6
7
8/2/2019 Barnett Quad Avi
8/20
Installing an Optional Scope
The recommended crossbow scope is a Barnett 4x32 mm
ve-reticle scope, which includes 1 rings to t a 3/8 dovetail
mount.
Remove peep sight rom the scope rail.
Position your scope by moving it orward or backward until
the proper eye relie is ound. This is typically three to our
inches rom your eye to the eyepiece when you are holding the
crossbow in a shooting position.
Ater the scope is installed you may remove the ront sight
bracket and pins.
Important: Be sure to tighten scope mount rings beore
shooting crossbow.
Crossbow Operation
Cocking Your Crossbow Be sure to apply Barnett lubewax to the center string
serving, cables and the fight track area rom the string to
the trigger area.
Place the oot stirrup on the
ground with one oot in the
stirrup and the stock resting
against your mid section. SeeFigure 7
Place both hands on the
string at each side o the
crossbow body no more than
inch rom crossbow body.
Using even pressure pull the
string back until it locks intothe trigger mechanism with an audible click. Be sure to apply
downward pressure against ight track.
Fig 7
8
8/2/2019 Barnett Quad Avi
9/20
Slowly release hand pressure on the string until you are sure
it is locked securely into the trigger mechanism. The crossbow
is now cocked with the saety on. Make sure that the string is
seated at the bottom o the tumbler. The tumbler is the parto the trigger that the string is resting on when cocked. I it is
resting at the top o the tumbler, use both thumbs and gently
push string down until it is seated at the bottom o the tumbler
to ensure proper arrow ight.
Note:The serving on the string has had a line on each side o the
ight surace marked at the actory. Ater cocking the crossbow
make sure that the marks on the string are showing equally on
each side o the trigger mechanism. Unevenly cocked crossbows
will have erratic arrow ight. When restringing your crossbow
mark the serving o the string, on each side o the ight track at
rest, where the string leaves the ight surace (track) and apply
Barnett Lubewax to the string serving and track surace.
Arrow Retainer
When loaded, the arrow should lie at in the ight groove. The
arrow retaining spring should not be twisted to the let or right
and should exert only enough pressure on the rear o the arrow
to hold it in place. It should not lit the ront o the arrow of the
ight groove. At this point, the arrow should be lying directly
parallel with the ight groove. We recommend the use o Barnett
arrows manuactured specically or your Barnett crossbow.
Loading your Crossbow
Place the arrow orward under the ront sight bracket and lay the
arrow on the ight surace. When using arrows with hal moon
nocks, be sure that the odd colored etch is placed in the ight
groove and that the concaved nock is parallel to the string.
Slide the arrow back under the arrow retaining spring and ullyinto the trigger mechanism. Note: The arrow retaining spring
should only exert enough pressure to hold the arrow in place
without liting it rom its position on the fight surace.
9
8/2/2019 Barnett Quad Avi
10/20
This will prevent your hands rom being struck by the string
as it travels orward. The velocity o the string hitting your
fngers will cause severe injury.
Firing your Crossbow
To re the arrow rom your crossbow:
Point the crossbow in a sae direction.
Slide the saety orward to the of position. The crossbow
will now re when the trigger is pulled. The saety MUST be
disengaged in this manner prior to every shot.
BE SURE TO KEEP YOUR FINGERS BELOW THE STOCK FORE
END (FLIGHT TRACK) WHILE SHOOTING. Note photos below.
Unloading your Crossbow
By ar, the easiest way to un-cock a cocked crossbow is to re an
arrow into a target or into the ground away rom debris, loose
rocks or other people.
Sighting-In the Crossbow
Using the rear peep sight and ront sight pins:
Place the rst sight pin near the top o the ront sight bracket.
10
8/2/2019 Barnett Quad Avi
11/20
Shooting at a target rom 10 yards, aim or the bulls eye. I the
rst shot is above the bulls eye, move the pin up (or down i
the shot is below the bulls eye).
I the rst shot is to the let o the bulls eye, screw the pin to thelet (or right i the shot is to the right).
TIP: Move the pin in the direction o the error, ollow the arrow.
Continue in this manner until you have three consecutive
shots into the bulls eye. Repeat this procedure with the
other pin,starting near the bottom o the sight bracket. It is
recommended that the bottom pin be sighted in to the 30 to 35
yard range.
Arrow Selection and Proper Flight
Due to the unique design o your Barnett crossbow, it is
imperative that only specied arrows are used. These arrows are
correctly weighted to absorb the high energy generated by the
compound design. Lighter arrows simulate a dryre condition
and will result in damage to the crossbow VOIDING the warranty.Barnetts 22 Carbon arrows are correctly spined.
DRY FIRING WILL VOID THE WARRANTY.
Use Barnetts 22 Carbon arrows with straight, ofset or helical
etches with Hal Moon Nock.
Recommended xed blade broadheads can be any three blade
low prole broadhead with a cutting diameter no larger than1-3/16.
When using xed blade broadheads, the blades must be
aligned with the etches o the arrow. This can be done by
placing a rubber o-ring between the broadhead and the arrow
ront insert.
Mechanical broadheads that simulate the ight o a eld point
may be used where legal.
11
8/2/2019 Barnett Quad Avi
12/20
8/2/2019 Barnett Quad Avi
13/20
When cocking your crossbow make a conscious efort to
hold the string on the ight track so as not to lit over the
arrowretainer.
Are you putting one etching down in the ight groove?
When using broadheads, line up the blades with the etches
on the arrow (using o-ring).
Have you checked the tiller to see i any adjustments should
be made? Tiller is the measurement between the base o the
limb and the bowstring. The tiller measurement tells you i
both limbs are equally stressed. Your bow is in proper tiller
when this measurement
is the same or both limbs.
Uneven tiller will cause
erratic arrow ight. All
crossbows are accurately
tillered at the actory prior
to shipping. To adjust the
tiller, use an allen wrenchand measuring tape as
shown in the illustration.
See Figure 8.
String Fraying
Are you using Barnett lubewax on the center string serving and
ight track every 5-10 shots and on the cables when needed?
Keep the trigger mechanism and ight surace ree o
obstruction.
Check or metal burrs on the ight track and arrow end caps.
Limbs Weak or Losing Power
Has the crossbow been dry red? (could cause limb to crack).
Inspect the limbs or splits or cracks.
Are you using Barnett string (the proper length)?
Fig 8
13
8/2/2019 Barnett Quad Avi
14/20
Care and Maintenance
Care o String
The owners kit contains a tube o lube wax that should beapplied to the center serving and ight track every 5 10 shots.
Lube wax should also be applied anywhere the cables make
contact with the Teon tape or ight track every 20 30 shots. To
extend the lie o your cables it is important to apply ARCHERY
STRING WAX to all areas o the cables and string every 30 - 50
shots or when white uzz begins to appear. I the crossbow has
been exposed to excessive moisture you may need to apply wax
sooner.
Care o AVi Limbs
AVi is an Anti Vibration Isolation process that encapsulates
standard bow limbs. I scratches or minor cuts appear in the limb
caused by contact rom outside objects, the bow limb is not
afected and should not be returned or warranty. Use caution
when placing in a bow press or when around sharp objects to
avoid damage to the covering itsel. Note: It is normal or AVi
limb material to displace around the Limb/Prod Area.
PRIOR TO EVERY SHOOTING SESSION, IT IS RECOMMENDED
THAT A COMPLETE CHECK OF CABLES, WHEELS, SCREWS
AND ARROWS BE MADE.
Always store your crossbow in a sae, dry place.
Do not expose your crossbow to extreme heat, such as closed,hot vehicles or near heat sources.
Inspect cables and strings or signs o wear. An authorized
service center or the actory should replace Cables showing
wear immediately.
Periodically put a ew drops o quality lightweight machine oil
in the trigger mechanism.
Periodically lubricate the eccentric wheel axels with lightweightmachine oil.
Keep the ight track and the string serving waxed, reducing
riction.14
8/2/2019 Barnett Quad Avi
15/20
Your prod can be let strung indenitely although we do not
recommend that the bow be let in the cocked position or
periods longer than our hours.
With reasonable care o your equipment and diligent practice, yourcrossbow will remain an accurate, highly efcient hunting weapon.
15
8/2/2019 Barnett Quad Avi
16/20
Warranty InormationThe stock, trigger mechanism and limbs are covered under a
limited one-year warranty. The AVi limbs are not covered or
cosmetic wear and tear. Our liability extends to parts and labor.
Not covered are: strings, cables, arrows, transportation o
product to our Service Center; damage caused by abuse,
modication or ailure to perorm normal maintenance; or any
other expense, consequential damages, coincidental damages,
or incidental expenses including damage to property or person.
There are no other warranties expressed or implied. This
warranty gives you specic legal rights and you may also haveother rights that vary rom state to state.
Warranty Registration Card must be mailed within 10 days o
purchase to validate the warranty.
TO OBTAIN SERVICE: Please call or a return authorization
number prior to sending the unit and write the RA# on the
outside o the package. Return the unit to an authorized Service
Center or directly to the actory. For a listing o authorizedservice centers please call the actory at the toll ree number
listed below. Attach to the product your name, address,
telephone number and a letter describing the problem. Careully
package and return product prepaid.
For urther inquiries contact the Sales Dept through the toll
ree number: 1-800-237-4507.
How to reach us:Barnett Outdoors, L.L.C., PO Box 934, Odessa, FL, 33556
Phone 813-920-2241 - Fax 813-920-5400
E-mail [email protected]
16
8/2/2019 Barnett Quad Avi
17/20
17
8/2/2019 Barnett Quad Avi
18/20
18
8/2/2019 Barnett Quad Avi
19/20
19
8/2/2019 Barnett Quad Avi
20/20
Cut out and mail immediately to:
Barnett Outdoors, L.L.C.P.O. Box 934
Odessa, FL 33556
WARRANTY CARD
Name______________________________ Age______
Address______________________________________
City____________________ State______ Zip_______
Date o Purchase__________ Phone # _____________
Place o Purchase________________ Price Paid______
Purchase Address______________________________