Date post: | 25-Oct-2015 |
Category: |
Documents |
Upload: | copymaster2 |
View: | 170 times |
Download: | 21 times |
LTC-7PNLithium-Thionyl Chloride Batteries
The LTC-7PN series was design specifically to be printed circuit board (PCB) compatible. With a low profile,prismatic shape, this battery is unique in the industryand a perfect match for space saving requirements.Available in 3 PCB mounting configurations, these cellsprovide high quality, high energy density, non-positionsensitive solutions to your high density electronics power needs.
TYPICAL LTC-7PN DISCHARGE CHARACTERISTICS AT VARIED TEMPERATURES
DISCHARGE TIME (HOURS)
1 mA 10 uA
3.93.83.73.63.53.43.33.23.13.02.92.82.72.62.5
2 4 6 8x 10
8x 100
2 4 6x 1,000
2 4 6 8x 10,00042 6 8
HIGH TEMPERATURE OPERATION AT 75°CTEMPERATURE OPERATION AT 20°CCOLD TEMPERATURE OPERATION AT -20°C
LTC-7PN Product Features
• Manufactured in the USA.
• Low profile, prismatic design.
• Stainless steel construction provides corrosionresistance, hermetic seal and structural integrity.
• Years of low rate continuous use.
• Stand-by use with 80% capacity retention after 15 years at room temperature.
• Highly efficient utilization of valuable board space.
• Wave solderable (limit solder bath exposure toa maximum of 5 seconds).
• High energy density compared to other chemistries.
• No charging circuits required.
• Higher cell voltage allows for fewer cells and high reliability.
• Flat discharge characteristics provide optimum voltage regulation.
• Non-pressurized system allow for high temperature usage.
• Ship unrestricted.
• Underwriters Laboratories recognized component.
Do you have questions concerning:
• What size battery you need?
• What is passivation and its effects?
• What is the maximum rate of this cell?
• Any other technical question?
If so, call our Engineers at (417) 659-9635 for detailed technical information.
LTC-7PN
Lithium-Thionyl Chloride Batteries
Lithium-Thionyl Chloride Batteries
The Power Source, Inc (800) 847-6947 PH (650) 960-3034 Faxe-mail: [email protected] • Web Site: www.the-powersource.com
WE CAN DESIGN TO FIT ANY APPLICATION.Our team of engineers can design any pin configuration required to fit your specialized application. If you don't see a battery configuration you need here, call us and we will begin working on a EPT part number just for you.
Specifications LTC-7PNNominal Open Circuit Voltage, 25°C ............................ 3.67 voltsNominal Working Voltage, 25°C...................................... 3.5 voltsNominal Capacity (350 hr. rate), 25°C .......................... 750 mAHVolume ............ .1625 cu. in.Weight .................... 6.8 GMSOperating Temperature ........
............-40°C to +95°CCase Material:
304 Stainless Steel,Hermetically Sealed (case negative polarity)
Terminal and Support Pins are.030" dia. (solder tinned)
0.40
0.30
POWERLEADS
1.00 1.10
0.30 0.175
0.175
0.6500.250
+
Specifications LTC-7PN-S4Nominal Open Circuit Voltage, 25°C ............................ 3.67 voltsNominal Working Voltage, 25°C...................................... 3.5 voltsNominal Capacity (350 hr. rate), 25°C .......................... 750 mAHVolume ............ .1625 cu. in.Weight .................... 6.8 GMSOperating Temperature ........
............-40°C to +95°CCase Material:
304 Stainless Steel,Hermetically Sealed (case negative polarity)
Terminal and Support Pins are.030" dia. (solder tinned)
.650
.250
+
1.00
.30
.48
.17
.050
.200
Specifications LTC-7PN-S6Nominal Open Circuit Voltage, 25°C ............................ 3.67 voltsNominal Working Voltage, 25°C...................................... 3.5 voltsNominal Capacity (350 hr. rate), 25°C ............................750 mAHVolume .................................................................... .1625 cu. in.Weight .......................................................................... 6.8 GMSOperating Temperature ...................................... -40°C to +95°CCase Material: 304 Stainless Steel, Hermetically Sealed
(case positive polarity)Terminal and Support Pins are .030" dia. (solder tinned)
.650
.17
.250
.25
+
1.00 1.10
SUPPORT PIN
The specifications on this sheetmay be changed
by Eagle-Picher Technologies, LLC,without notice.
Part Number Voltage Capacity (mAh) Length (in.) Width (in.) Thickness (in.) Weight (g)
LTC-7PN 3.5 750 1.00 0.65 0.25 6.8
LTC-7PN-S2 3.5 750 1.00 0.65 0.25 6.8
LTC-7PN-S4 3.5 750 0.65 0.25 1.00 6.8
* LTC-7PN-S5 3.5 750 1.00 0.65 0.25 7.1
LTC-7PN-S6 3.5 750 1.00 0.25 0.65 6.8
** LTC-7PN-SM-S1 3.5 750 1.00 0.65 0.25 6.8
* Supplied with Molex connector ** Surface Mount (Reflow soldering not acceptable)