ITEM DESCRIPTION UNIT 2010Q1 MEAN

2010Q2 MEAN

2010Q3 MEAN

2010Q4 MEAN

2011Q1 MEAN

I EXCAVATION

1 GENERAL EXCAVATION

1.1 Oversite Excavation

Excavate over site, commencing from ground level, to reduce level

A average 100mm deep m2 1.94 1.95 1.93 1.94 1.94B average 200mm deep m2 2.40 2.38 2.37 2.38 2.38C average 300mm deep m2 3.46 3.46 3.33 3.33 3.33D over 300mm deep m3 12.08 12.00 11.98 12.00 12.00

1.2 Pit/Trench Excavation

Excavate to form pit or trench, commencing from reduced level

A ne 2.00m deep m3 23.73 24.03 23.97 24.17 24.33B 2.00 - 4.00m deep m3 26.00 25.77 25.70 25.83 26.00C 4.00 - 6.00m deep m3 29.17 29.17 29.09 27.77 27.83D extra over for each 2.00m deep m3 6.03 6.00 6.00 6.00 6.00

1.3 Basement Excavation

Excavate to form basement, commencing from reduced level

A ne 2.00m deep m3 16.33 16.53 16.50 16.60 16.83B 2.00 - 4.00m deep m3 18.00 17.83 17.77 17.83 18.00C 4.00 - 6.00m deep m3 20.87 20.87 20.80 20.83 21.00D extra over for each 2.00m deep m3 2.53 2.53 2.53 2.57 2.60

1.4 Break Up Obstruction

Extra over excavation for breaking up obstruction below ground level using mechanical means

A rock m3 92.17 92.17 92.17 92.67 93.00

2 FILLING

2.1 Backfilling

Backfill around trench, column base, pile cap, foundation, beam and pier hole

A excavated material obtained within the site m3 8.47 8.47 8.47 8.47 8.50B earthfilling obtained from contractor's own

sourcem3 10.23 10.23 10.23 10.23 10.27

2.2 Filling and Forming Embankments

Deposit, spread, level, compact and consolidate in layers of 150mm thick to make up levels

A excavated material obtained within the site m3 7.33 7.33 7.33 7.33 7.37B earthfilling obtained from contractor's own

sourcem3 10.93 10.93 10.93 10.93 10.97

Unit Rates - ExcavationLast Updated on 13/05/11

[The data will be updated on a quarterly basis]

Page 1/34

ITEM DESCRIPTION UNIT 2010Q1 MEAN

2010Q2 MEAN

2010Q3 MEAN

2010Q4 MEAN

2011Q1 MEAN

2.3 Hardcore and Aggregate

Spread, level, compact, ram and consolidateA hardcore, including blinding with sand m3 50.17 50.17 50.17 50.17 50.17

3 DISPOSAL

3.1 Excavated Material

Remove excavated material off site A to contractor's own dumping site m3 12.57 12.57 12.57 12.57 12.83

Page 2/34

ITEM DESCRIPTION UNIT 2010Q1 MEAN

2010Q2 MEAN

2010Q3 MEAN

2010Q4 MEAN

2011Q1 MEAN

II CONCRETE WORK

1 IN-SITU CONCRETE

1.1 Lean/Mass Concrete

Lean or Mass concrete complying with BS 8110 in any location

A grade 15 m3 187.33 192.50 193.90 199.57 204.00B grade 20 m3 196.67 202.17 203.97 210.97 212.67

1.2 Reinforced Concrete

Reinforced concrete complying with BS 8110 in any location

A grade 25 m3 123.60 126.33 126.40 132.83 138.00B grade 30 m3 128.68 128.78 128.83 133.88 137.75C grade 35 m3 131.65 131.45 131.23 136.63 140.50D grade 40 m3 134.88 134.25 134.03 140.00 144.00E grade 50 m3 138.67 140.27 139.93 146.17 152.00F Extra over for waterproofing agent m3 44.00 44.00 44.00 44.17 44.67

2 REINFORCEMENT

2.1 Bar Reinforcement

Mild steel bar reinforcement complying with SS 18 in any location

A 6mm diameter kg 1.53 1.59 1.54 1.56 1.56B 10mm diameter kg 1.53 1.59 1.54 1.56 1.56C 13mm diameter kg 1.53 1.59 1.54 1.56 1.56

High tensile steel bar reinforcement complying with SS 2 in any location

D 10mm diameter kg 1.52 1.58 1.52 1.55 1.55E 12/13mm diameter kg 1.52 1.58 1.52 1.55 1.55F 16mm diameter kg 1.52 1.58 1.52 1.55 1.55G 20mm diameter kg 1.52 1.58 1.52 1.55 1.55H 25mm diameter kg 1.52 1.58 1.52 1.55 1.55I 28mm diameter kg 1.52 1.58 1.52 1.55 1.55J 32mm diameter kg 1.52 1.58 1.52 1.55 1.55K 40mm diameter kg 1.52 1.58 1.52 1.55 1.55

2.2 Fabric Reinforcement

Welded fabric reinforcement complying with SS 32 and well lapped (measured net)

A Reference No A6 m2 6.59 6.76 6.74 6.89 6.92B Reference No A7 m2 7.40 7.61 7.59 7.79 7.85C Reference No A8 m2 8.77 9.01 8.96 9.12 9.12D Reference No A9 m2 10.64 11.01 10.91 11.10 11.14E Reference No B6 m2 9.08 9.44 9.37 9.59 9.60F Reference No B7 m2 10.15 10.54 10.47 10.73 10.80G Reference No B8 m2 12.27 12.73 12.63 12.94 12.94H Reference No B9 m2 13.60 14.06 13.93 14.22 14.18I Reference No B10 m2 14.91 15.43 15.26 15.63 15.61J Reference No D6 m2 9.43 9.74 9.67 9.89 9.86

Unit Rates - Concrete WorkLast Updated on 13/05/11

[The data will be updated on a quarterly basis]

Page 3/34

ITEM DESCRIPTION UNIT 2010Q1 MEAN

2010Q2 MEAN

2010Q3 MEAN

2010Q4 MEAN

2011Q1 MEAN

2.2 Fabric Reinforcement

Welded fabric reinforcement complying with SS 32 and well lapped (measured net)

K Reference No D8 m2 13.70 14.13 14.00 14.28 14.24L Reference No D9 m2 18.06 18.69 18.52 18.91 18.86

3 FORMWORK

3.1 Timber Formwork

Sawn formwork to in-situ concrete including strutting ne 3.50m high

A flat surface of suspended slab m2 30.70 30.37 30.50 31.17 31.17B vertical surface of pilecap, ground beam, etc. m2 30.70 30.37 30.50 31.17 31.17

C vertical surface of column, walls m2 30.70 30.37 30.50 31.17 31.17D vertical curved surface of column, wall m2 37.67 38.17 38.33 38.33 38.50E sides and soffits of beams m2 32.20 31.87 32.00 32.00 32.00F vertical edge for each 100mm high m 3.05 3.05 3.05 3.05 3.05

Wrought formwork to in-situ concrete including strutting ne 3.50m high

G flat surface m2 31.05 31.53 31.65 31.65 31.65H vertical surface m2 31.05 31.53 31.65 31.65 31.65I curved surface m2 41.18 42.35 42.53 42.53 42.63

Extra over formwork for strutting exceeding 3.50mJ each 1.50m high m2 2.00 2.03 2.03 2.03 2.03

3.2 Metal Formwork

Metal formwork to in-situ concrete including strutting ne 3.50m high

A vertical surface m2 49.60 51.73 51.43 52.43 52.43B vertical curved surface m2 56.73 58.97 58.63 59.30 59.30C 0.75mm Bondek/Condeck to flat surface of

suspended slabm2 51.63 53.80 53.50 54.17 54.17

D 1.00mm Bondek/Condeck to flat surface of suspended slab

m2 56.42 59.20 58.87 59.53 59.53

Extra over formwork for strutting exceeding 3.50m high

E each 1.50m high m2 5.67 5.83 5.83 5.87 5.87

4 PRECAST CONCRETE

4.1 Precast Concrete Hollow Core Slab

A 265mm m2 95.82 95.82 95.82 96.47 95.33B 340mm m2 111.37 111.37 111.37 111.93 110.33

5 EXPANSION JOINTS

5.1 Joint Fillers

Compressible non-extruding bitumen impregnated fibreboard to joint, including all necessary formwork

A 10mm thick m2 24.63 24.63 24.63 24.63 24.63B 12mm thick m2 29.38 29.38 29.38 29.38 29.38C 25mm thick m2 41.99 41.99 41.99 41.99 41.99

Page 4/34

ITEM DESCRIPTION UNIT 2010Q1 MEAN

2010Q2 MEAN

2010Q3 MEAN

2010Q4 MEAN

2011Q1 MEAN

5.2 Joint Sealant

Polysulphide sealer squeezed into jointA 25 x 15mm joint m 14.99 14.99 14.99 14.99 14.99B 25 x 25mm joint m 21.14 21.14 21.14 21.14 21.14

5.3 Prestressing Cables

Cable stand in beams complete with sleeves,anchors and all necessary accessories

A 12x12.9mm diameter kg 5.40 5.57 5.57 5.57 5.57

6 WATERPROOF MEMBRANE

6.1 Damp Proof Membrane

Waterproofing sheet laid to top,side or underside of concrete structure

A 0.6mm thick polyethylene moisture barrier m2 5.63 5.63 5.70 5.73 5.73B 0.8mm thick polyethylene moisture barrier m2 8.60 8.60 8.70 8.73 8.73C approved bituminous m2 25.59 25.59 25.76 25.83 25.33

7 INTEGRATED FINISH

Power floated finish to suspended slabsA generally m2 4.57 4.57 4.57 4.57 4.57B with `Mastercron' or approved equivalent non-

metallic hardenerm2 16.57 16.57 16.57 16.57 15.90

Page 5/34

ITEM DESCRIPTION UNIT 2010Q1 MEAN

2010Q2 MEAN

2010Q3 MEAN

2010Q4 MEAN

2011Q1 MEAN

III BRICKWORK AND BLOCKWORK

1 CLAY BRICKS

1.1 Common Brickwork (Standard Size)

Common brick in cement mortar (1:4) with mortar plasticiser

A 115mm thick wall m2 30.13 30.88 30.88 30.88 30.88B 230mm thick wall m2 60.25 61.25 61.25 61.25 61.25

1.2 Facing Brickwork

First quality facing brick in cement mortar (1:4) with plasticiser

A 115mm thick wall m2 41.97 42.37 42.37 42.30 42.30B 215mm thick wall m2 85.80 86.63 86.63 86.13 86.13

2 CONCRETE BLOCKS

2.1 Hollow Blockwork

Hollow concrete block in cement mortar (1:4)A 390x190x90mm thick wall m2 25.33 25.60 25.60 25.43 25.67B 390x190x190mm thick wall m2 48.80 49.27 49.27 48.97 49.17

Unit Rates - Brickwork and BlockworkLast Updated on 13/05/11

[The data will be updated on a quarterly basis]

Page 6/34

ITEM DESCRIPTION UNIT 2010Q1 MEAN

2010Q2 MEAN

2010Q3 MEAN

2010Q4 MEAN

2011Q1 MEAN

IV ROOFING

1 TILE ROOFING

1.1 Clay Roof Tiles

`GR 13' French clay interlocking roof tiles with galvanised nails on every 4th course

A generally m2 57.26 57.26 57.26 57.26 57.26

Extra over `GR 13' French clay for roof accessories

B ridge or hip tile m 42.12 42.12 42.12 42.12 42.12

"Roman GR 13" or other equal roof tiles fixed to batten with galvanised nails at approximately 400mm centres

C generally m2 47.78 47.78 47.78 47.78 47.78

Extra over GR13 for roof accessoryD ridge or hip tile m 39.25 39.25 39.25 39.25 39.25

TBF Romane tile fixed to battens (measured separately) with galvanised nails at approximately 400mm centres

E generally m 55.99 55.99 55.99 55.99 55.99

Extra over `TBF Romane tile' for roof necessary

F ridge or hip tile m 42.78 42.78 42.78 42.78 42.78

1.2 Concrete Roof Tiles

Redland `51' or Pelangi interlocking concrete roofing tile complying with SS310 and SS CP43 fixed to battens (measured separately) with galvanised nails at every other course

A generally m2 21.60 21.60 21.60 21.60 21.60

Extra over for Redland `51' or Pelangi roof accessories

B ridge tile m 13.84 13.84 13.84 13.84 13.84

Monier interlocking concrete roofing tile complying with SS310 and SS CP43 fixed to battens (measured separately) with galvanised nails at every other course

C generally m2 35.07 35.07 35.07 35.07 35.07

Extra over Monier roof accessoryD ridge tile m 21.10 21.10 21.10 21.10 21.10

Unit Rates - RoofingLast Updated on 13/05/11

[The data will be updated on a quarterly basis]

Page 7/34

ITEM DESCRIPTION UNIT 2010Q1 MEAN

2010Q2 MEAN

2010Q3 MEAN

2010Q4 MEAN

2011Q1 MEAN

2 BUILT-UP ROOFING

2.1 Insitu Finishes

`Vermiculite' lightweight screed wood floated finish laid to falls on concrete to receive waterproof membrane

A 25mm m2 15.81 15.81 15.81 15.81 15.81B 50mm m2 26.29 26.29 26.29 26.29 26.29C add or deduct for each 10mm thickness m2 5.78 5.78 5.78 5.78 5.78

`Ais-Texsa' lightweight concrete insulating underbeds to flat roof to falls

D 75mm m2 16.04 16.04 16.04 16.04 16.04E add or deduct for each 10mm thickness m2 4.38 4.38 4.38 4.38 4.38

Cement and sand (1:3) screed with `Sika' waterproofing additive

F 25mm m2 15.43 15.60 16.00 16.17 16.50G 50mm m2 24.63 24.90 25.50 25.50 25.87H add or deduct for each 10mm thickness m2 5.20 5.20 5.20 5.20 5.27

Cement and sand (1:3) screedI 25mm m2 13.70 14.08 14.38 14.38 14.50J 50mm m2 17.17 17.60 18.17 18.17 18.33K add or deduct for each 10mm thickness m2 3.78 3.78 3.78 3.78 3.82

2.2 Waterproofing Membranes

Roof waterproofing membrane system on screed (measured separately)

A Nuralite sheet m2 53.67 53.67 53.67 53.67 53.67

3mm Mortar Plas waterproofing membrane with minimum 75mm laps

B to flat surface m2 21.67 21.67 21.67 21.67 21.67C to vertical surface m2 22.69 22.69 22.69 22.69 22.69

Bituthene 3000 waterproofing membraneD to flat surface m2 26.80 26.80 26.80 26.80 26.80E to vertical surface m2 26.80 26.80 26.80 26.80 26.80

Hypalon waterproofing membraneF to flat surface m2 30.73 30.73 30.73 30.73 30.73G to vertical surface m2 30.73 30.73 30.73 30.73 30.73

`Apex' waterproofing membraneH to flat surface m2 26.54 26.54 26.54 26.54 26.54I to vertical surface m2 26.54 26.54 26.54 26.54 26.54

Carboeol waterproof membraneJ to flat surface m2 27.69 27.69 27.69 27.69 27.69K to vertical surface m2 29.97 29.97 29.97 29.97 29.97

2mm `Texsaplas' exposed synthetic waterproofing membrane

L gutter m2 20.98 20.98 20.98 20.98 20.98

Page 8/34

ITEM DESCRIPTION UNIT 2010Q1 MEAN

2010Q2 MEAN

2010Q3 MEAN

2010Q4 MEAN

2011Q1 MEAN

2.2 Waterproofing Membranes

0.90mm `Uniroof' waterproofing membraneM flat surface m2 29.41 29.41 29.41 29.41 29.41N vertical surface m2 30.57 30.57 30.57 30.57 30.57

2.3 Panel Roofing

Waterproofed cement and sand (1:3) screedA 25mm thick (average) m2 16.46 16.66 17.13 17.13 17.16B 50mm thick (average) m2 29.90 30.27 31.10 31.10 31.10

Precast concrete panel grade 20 roof slabC 600 x 600 x 50mm m2 31.93 32.26 32.26 32.93 32.93

3 PROFILED SHEET ROOFING OR CLADDING

3.1 Steel Deckings

Galvanised steel roof or wall cladding with zincalume coating and colorbond finish on one side, fixed to steel or timber framing (measured separately) with fixing clips,bolts and nails

A 0.47mm thick Stramit `Multideck Hi-Ten' sheet m2 33.00 33.00 33.00 33.00 33.00

B 0.48mm thick BlueScope Lysaght `Trimdek Hi-Ten' sheet

m2 35.47 35.47 35.47 35.47 35.47

C 0.53mm thick Stramit `Speed Deck Hi-Ten' sheet

m2 37.93 37.93 37.93 37.93 37.93

D 0.53mm thick BlueScope Lysaght Colorbond XRW Kliplok Hi-Ten roofing sheet

m2 41.57 41.57 41.57 41.57 41.57

Galvanised steel roof or wall cladding with zincalume coating and colorbond finish on one side, fixed to steel or timber framing (measured separately) with fixing clips,bolts and nails

E 0.47mm thick BlueScope Lysaght Colorbond XRW Crimp Curved Trimdek Hi-Ten roofing sheet

m2 45.63 45.63 45.63 45.63 45.63

F 0.61mm thick Stramit `C-Clad' sheet m2 44.90 44.90 44.90 44.90 44.90G 0.65mm thick Stramit `Sped Deck Hi-Ten'

sheetm2 50.57 50.57 50.57 50.57 50.57

4 RAINWATER GOODS

4.1 Flashings/Cappings

0.61mm thick galvanised steel standard rain-water goods with zincalume coating and colorbond finish including fixing clips, bolts and nails

A girth flashing m2 34.50 34.50 34.50 34.50 35.20B girth capping m2 44.70 44.70 44.70 44.70 45.23

1.0mm thick Zincalume (unpainted) box gutter including fixing accessories

C girth flashing m2 49.70 49.70 49.70 49.70 49.73D girth capping m2 52.81 52.81 52.81 52.81 52.81

Page 9/34

ITEM DESCRIPTION UNIT 2010Q1 MEAN

2010Q2 MEAN

2010Q3 MEAN

2010Q4 MEAN

2011Q1 MEAN

4.1 Flashings/Cappings

1mm thick natural anodised aluminium including fixing clips, bolts and nails

E girth flashing m2 48.77 48.77 48.77 48.77 47.37F girth capping m2 57.03 57.03 57.03 57.03 55.66

2mm thick natural anodised aluminium including fixing clips, bolts and nails

G girth flashing m2 56.39 56.39 56.39 56.39 56.82H girth capping m2 56.99 56.99 56.99 56.99 57.66

Stainless steel in No 4 brush finish including fixing chips, bolts and nails

I girth flashing m2 67.09 67.09 67.09 67.09 67.09

4.2 Gutters

1.2mm thick galvanised steel open box gutter with zincalume coating and colorbond finish including brackets, fixing clips, bolts, nails and laying to falls

A gutter m2 95.40 95.40 95.40 95.40 95.40

4.3 UPVC Downpipes

Unplasticied polyvinyl chloride rainwater downpipe including solvent welded joints and jointing to sumps and drains

A 75mm diameter m 35.73 36.37 34.87 35.33 36.00B 100mm diameter m 40.63 41.67 40.00 40.50 41.67C 150mm diameter m 54.10 55.07 53.43 54.00 55.00D 250mm diameter m 66.33 67.57 64.67 64.67 65.33

5 SUNDRIES

5.1 Insulation

Insulation material to roofA 50mm thick fibreglass insulation, density 16

kg/m3m2 7.00 7.00 7.00 7.00 7.33

B 25mm thick m2 5.67 5.67 5.67 5.67 5.67

Insulation material to roofC ACI Sisalation 450 double-sided, double

reinforced aluminum foil insulation paper with 150mm laps

m2 5.08 5.08 5.08 5.08 5.08

D 50mm `Roofmate' or equivalent extruded polystyrene insulation board

m2 18.67 18.67 18.67 18.67 18.67

5.2 Wire Mesh

Wire mesh to roof space including dressing over purlins (measured net)

A BRC Reference No 3315 (75 x 75 x 1.5mm diameter)

m2 3.76 3.76 3.76 3.76 3.86

5.3 Purlin

A Lysaght Z20020 purlin m 25.33 25.33 25.33 25.33 25.33B Lysaght C20025 purlin m 30.70 30.70 30.70 30.70 30.70

Page 10/34

ITEM DESCRIPTION UNIT 2010Q1 MEAN

2010Q2 MEAN

2010Q3 MEAN

2010Q4 MEAN

2011Q1 MEAN

V CARPENTRY AND JOINERY

1 CARCASSING

1.1 Structural Timber

Sawn timber in carpenter's worksA kapur m3 1910.00 1910.00 1910.00 1910.00 1910.00B balau m3 2128.33 2128.33 2128.33 2128.33 2128.33C kempas m3 1453.33 1453.33 1453.33 1453.33 1453.33D chengal m3 2886.83 2886.83 2886.83 2886.83 2886.83

1.2 Timber Preservation

Extra over structural timber for pressure impregnation with a suitable wood preservative to an average dry salt retention of 5.6kg/m3 and complying with SS 72 and treated in accordance with SS CP 1

A generally m3 74.67 74.67 74.67 74.67 74.67

2 FRAMING

2.1 Mouldings

Bead, picture rail, architrave, fillet and cornice and the like not exceeding 500mm2 in sectional area including gluing and nailing

A teak m 12.55 12.55 12.55 12.55 12.55B chengal m 8.41 8.41 8.41 8.41 8.41C balau m 9.47 9.47 9.47 9.47 9.47

2.2 Joinery Framing

Wrought kapur in frame and the likeA per 1000mm2 sectional area m 4.78 4.78 4.78 4.78 4.78

Wrought tanalised chengal in frame and the like

B per 1000mm2 sectional in area m 21.04 21.04 21.04 21.04 21.04

Wrought teak in frame and the like C per 1000mm2 sectional in area m 31.55 31.55 31.55 31.55 31.55

Wrought oak in frame and the likeD per 1000mm2 sectional in area m 39.87 39.87 39.87 39.87 39.87

2.3 Handrails

Wrought oak in handrails and the likeA per 1000mm2 sectional area m 69.48 69.48 69.48 69.48 69.48

Wrought kapur in handrails and the likeB per 1000mm2 sectional area m 26.38 26.38 26.38 26.38 26.38

Wrought Balau in handrails and the likeC per 1000mm2 sectional area m 33.66 33.66 33.66 33.66 33.66

Unit Rates - Carpentry and JoineryLast Updated on 13/05/11

[The data will be updated on a quarterly basis]

Page 11/34

ITEM DESCRIPTION UNIT 2010Q1 MEAN

2010Q2 MEAN

2010Q3 MEAN

2010Q4 MEAN

2011Q1 MEAN

2.4 Stud Partition Framing

Sawn kapur framing fixed at 600mm centres bothways

A 50 x 50mm cross-section m2 25.06 25.06 25.06 25.06 25.06B 50 x 75mm cross-section m2 36.23 36.23 36.23 36.23 36.23

3 LININGS

3.1 Calcium Silicate Boards

Calcium silicate board reinforced with selected fibres and fillers (Class 0) including pointing

A 6mm thick m2 21.56 21.56 21.56 21.78 21.78B 9mm thick m2 30.42 30.42 30.42 30.73 30.73C 12mm thick m2 33.71 33.71 33.71 33.75 33.75

3.2 Cement Building Boards

Cement building board including pointingA 6mm thick m2 18.85 18.85 18.85 18.85 18.85B 12mm thick m2 26.24 26.24 26.24 26.24 26.24

3.3 Gypsum Boards

Bare finish gypsum board including pointingA 10mm thick m2 16.92 16.92 16.92 16.92 17.39B 13mm thick m2 20.85 20.85 20.85 20.85 21.45

3.4 Plywoods

Non-waterproofed plywood complying with SS1

A 6mm thick m2 16.32 16.32 16.32 16.32 16.33B 12mm thick m2 21.17 21.17 21.17 21.17 21.18C 18mm thick m2 26.48 26.48 26.48 26.48 26.51D 25mm thick m2 37.77 37.77 37.77 37.77 37.84

Waterproofed plywood type WBPE 6mm thick m2 19.78 19.78 19.78 19.78 19.79F 12mm thick m2 26.18 26.18 26.18 26.18 26.18G 18mm thick m2 33.39 33.39 33.39 33.39 33.41H 25mm thick m2 37.55 37.55 37.55 37.55 37.66

3.5 Laminated Plastics

Laminated plastic sheet to BS 3796 including compatible adhesive

A 0.8mm thick Formica m2 24.08 24.08 24.08 24.08 24.08B 0.8mm thick Print m2 21.17 21.17 21.17 21.17 21.17C 1.0mm thick Formica m2 28.16 28.16 28.16 28.16 28.16

Laminated plastic sheet to BS 3796 including compatible adhesive

D 1.0mm thick Print m2 23.12 23.12 23.12 23.12 23.12E 1.2mm thick Print m2 26.23 26.23 26.23 26.23 26.23F 1.3mm thick Print m2 26.08 26.08 26.08 26.08 26.08G 1.3mm thick Formica m2 31.28 31.28 31.28 31.28 31.28

Page 12/34

ITEM DESCRIPTION UNIT 2010Q1 MEAN

2010Q2 MEAN

2010Q3 MEAN

2010Q4 MEAN

2011Q1 MEAN

4 WALL INSULATION

4.1 Fibreglass

Supply and fix fibreglassA 50mm thick, 48 kg/m3 m2 22.70 22.70 22.70 22.70 22.70B 75mm thick, 48 kg/m3 m2 28.38 28.38 28.38 28.38 28.38

4.2 Mineral Wool

Supply and fix mineral woolA 25mm thick, 48 kg/m3 m2 12.75 12.75 12.75 12.75 12.75B 50mm thick, 48 kg/m3 m2 17.38 17.38 17.38 17.38 17.38C 25mm thick, 80 kg/m3 m2 14.75 14.75 14.75 14.75 14.75

5 PANELLING

5.1 Timber Panelling

100mm wide tongued and grooved wrought boarding fixed to battens (measured separately)

A 13mm thick ramin m2 55.39 55.39 55.39 55.39 55.50B 19mm thick ramin m2 72.86 72.86 72.86 72.86 72.94C 13mm thick chengal m2 46.31 46.31 46.31 46.31 46.52D 19mm thick chengal m2 52.39 52.39 52.39 52.39 52.46E 25mm thick chengal m2 113.16 113.16 113.16 113.16 113.83

5.2 Woodwool Slab Wall Panelling

Supply and fix woodwool slab to wallA 50mm thick m2 17.83 17.83 17.83 17.83 17.83

5.3 Glasal Panels

`Glasal' fully compressed autoclaved fibre cement sheet panel fixed to timber frame

A 45mm thick panel fixed to timber frame and bend

m2 120.92 120.92 120.92 120.92 120.92

6 FLOORING

6.1 Floor Boards

100mm wide wrought plain edge floor board fixed to bearers (measured separately)

A 19mm thick teak m2 86.36 86.36 86.36 86.36 86.36B 25mm thick teak m2 103.99 103.99 103.99 103.99 103.99C 19mm thick chengal m2 52.15 52.15 52.15 52.15 52.15D 25mm thick chengal m2 62.80 62.80 62.80 62.80 62.80

100mm wide wrought tongued and grooved floor board fixed to bearers (measured separately)

E 19mm thick teak m2 107.32 107.65 107.65 107.65 107.65F 25mm thick teak m2 127.98 128.65 128.65 128.65 128.65G 19mm thick chengal m2 74.17 74.50 74.50 74.50 74.50H 25mm thick chengal m2 85.38 85.72 85.72 85.72 85.72I 20mm thick oak m2 150.33 150.33 150.33 150.33 150.33

Page 13/34

ITEM DESCRIPTION UNIT 2010Q1 MEAN

2010Q2 MEAN

2010Q3 MEAN

2010Q4 MEAN

2011Q1 MEAN

6.2 Block/Parquet Flooring

Teak parquet floor laid to herring-bone pattern, bedded and jointed with and including one coat of bituminous emulsion

A 12mm thick m2 43.25 43.25 43.25 43.82 43.82B 20mm thick m2 54.63 54.63 54.63 56.13 56.13

Ramin parquet floor in mosaic patternC 8mm thick m2 99.60 99.60 99.60 99.60 99.60

7 DOORS

7.1 Kapur Flush Doors

Solid core flush door complying with BS 459 comprising hardwood lipping around 16mm wide vertical core strips glued and well cramped together and covered on both sides with 6mm thick plywood

A 45mm thick m2 243.27 243.27 248.17 248.17 250.00B 50mm thick m2 260.97 260.97 266.23 266.23 268.33

Skeleton framed flush door complying with BS 459 comprising hardwood lipping all round stiles and rails covered on both sides with 6mm thick plywood

C 38mm thick m2 106.00 106.00 109.67 109.67 110.00D 45mm thick m2 120.00 120.00 124.00 124.00 124.33E 50mm thick m2 123.00 123.00 127.00 127.00 128.00

Hollow core flush door complying with BS 459 comprising skeleton framing, hardwood lipping all round and covered on both sides with 6mm thick plywood

F 38mm thick m2 178.33 176.67 180.67 180.67 183.33G 45mm thick m2 198.20 197.67 202.17 202.17 204.33

7.2 Kapur Panelled Doors

Panelled door complying with BS 459 in 3 panels comprising stiles and rails framed around 20mm thick plywood

A 38mm thick m2 186.29 186.29 186.29 186.29 186.29B 45mm thick m2 220.72 220.72 220.72 220.72 220.72

Labour only to form observation panels of any size in doors

C generally No 31.68 31.68 31.68 31.68 31.76

7.3 Timber Fire Door

1/2 hour rated fire door complying with SS 332 complete with fire proofed cylinder lockset, stainless steel ball bearing hinges, flush bolt, door closer and frame

A 900x2100x45mm thick, double leaf No 694.96 694.86 697.19 697.19 697.19B 900x2100x45mm thick, single leaf No 717.28 717.17 719.83 719.83 719.83C 1200x2100x45mm thick, single unequal leaf No 907.59 907.47 910.47 910.47 910.47D 1200x2100x45mm thick, double unequal leaf No 969.81 969.67 972.87 972.87 972.34E 1800x2100x45mm thick, double leaf No 1438.27 1438.07 1442.73 1442.73 1441.40

Page 14/34

ITEM DESCRIPTION UNIT 2010Q1 MEAN

2010Q2 MEAN

2010Q3 MEAN

2010Q4 MEAN

2011Q1 MEAN

7.3 Timber Fire Door

1 hour rated fire door complying with SS 332 complete with fire proofed cylinder lockset, stainless steel ball bearing hinges, flush bolt, door closer and frame

F 900x2100x45mm thick, single leaf No 826.21 828.90 828.90 828.90 828.90G 1200x2100x45mm thick, double unequal leaf No 1303.47 1307.90 1307.90 1307.90 1307.90

2 hour rated fire door complying with SS 332 complete with fire proofed cylinder lockset, stainless steel ball bearing hinges, flush bolt, door closer and frame

H 900x2100x45mm thick, single leaf No 1438.50 1438.50 1438.50 1438.50 1438.57

8 PARTITIONS

Drywall partition covered both sides with 2 layers of 13mm gypsum plasterboards with fibreglass/rockwood insulation including steel studs,fixing and jointing accessories

A wall m2 61.35 63.77 63.77 63.77 62.50

150mm one hour fire rated gypsum drywall partition covered both sides with 2 layers 13mm gypsum plasterboard including steel studs fixing and jointing accessories

B wall m2 80.90 81.63 81.63 81.83 81.83

214mm two hour rated gypsum drywall partition covered both sides with 3 layers 19mm,gypsum plasterboard including steel studs, fixing and jointing accessory

C wall m2 149.57 150.97 150.97 151.07 151.07

Page 15/34

ITEM DESCRIPTION UNIT 2010Q1 MEAN

2010Q2 MEAN

2010Q3 MEAN

2010Q4 MEAN

2011Q1 MEAN

VI STRUCTURAL STEELWORK & METAL WORK

1 STRUCTURAL STEELWORK

1.1 Mild Steel Members

Mild steel member complying with BS 4360 grade 55 in welded or bolted construction

A universal column kg 4.96 5.20 5.22 5.28 5.30B universal beam kg 4.96 5.20 5.22 5.28 5.30C connection plates kg 5.09 5.33 5.33 5.38 5.37D composite beam kg 4.96 5.20 5.22 5.28 5.30

Mild steel member complying with BS 4360 Grade 50 in welded or bolted construction

E universal column kg 5.03 5.27 5.27 5.33 5.37F universal beam kg 5.03 5.27 5.27 5.33 5.37G universal curved beam kg 5.32 5.60 5.60 5.67 5.70H connection plate kg 5.26 5.53 5.53 5.60 5.63I roof truss kg 5.10 5.37 5.37 5.43 5.47

Mild steel member complying with BS 4360 grade 43 in stanchion, beam, girder, roof truss, purlin, cleat and bracket

J solid section kg 5.03 5.23 5.23 5.30 5.33K hollow section kg 5.10 5.30 5.30 5.37 5.40

2 METAL WORK

2.1 Mild Steel Members

A hollow section, flat, rod, angle and channel complying with BS 4360 Grade 43C

kg 5.08 5.33 5.37 5.37 5.37

B 50mm diameter tubular rail complying with SS17; light duty

m 51.83 52.97 53.63 53.63 53.63

C 38mm diameter tubular baluster/balustrade complying with SS 17; light duty

m 43.00 43.93 44.27 44.27 44.27

2.2 Aluminium Members

Aluminium members complying with BS 1474

A 50mm diameter, 1.5mm thick natural anodised tubular rail

m 46.33 46.33 47.00 47.00 47.00

B 38mm diameter, 1.5mm thick natural anodised tubular baluster/balustrade

m 37.17 37.17 37.83 37.83 37.83

Unit Rates - Structural Steelwork & Metal WorkLast Updated on 13/05/11

[The data will be updated on a quarterly basis]

Page 16/34

ITEM DESCRIPTION UNIT 2010Q1 MEAN

2010Q2 MEAN

2010Q3 MEAN

2010Q4 MEAN

2011Q1 MEAN

2.3 Stainless Steel Members

Stainless steel members (AISI 304) with 180 grit finish

A 50mm diameter, 1.5mm thick natural anodised tubular rail

m 103.90 105.20 105.90 105.90 105.90

B 38mm diameter, 1.5mm thick natural anodised tubular baluster/balustrade

m 81.33 82.50 83.33 83.33 83.33

Stainless steel 2mm thick No 8 mirror finishC 70mm diameter 2.50mm thick tubular rail m - - - - -D cladding with all necessary steel bracket m2 2,506.67 2,555.10 2,573.30 2,573.30 2,573.30E ceiling lining m2 2,744.67 2,795.17 2,811.30 2,811.30 2,811.30

2.4 Stud Partition Framing

Galvanised steel `C' channel framing fixed at 600mm centres bothways including forming door opening in partition

A 76 x 40 x 1mm thick m2 48.00 48.00 48.00 48.00 48.00

3 MILD STEEL CONNECTIONS

3.1 Mild Steel Bolts

Mild steel plain bolts complying with BS 4190 including head, nut and washer

A 12mm diameter grade 8.8 black bolt, ne 75mm long

No 1.73 1.73 1.73 1.73 1.73

B 12mm diameter grade 8.8 black bolt, 75 - 150mm long

No 15.73 15.73 15.73 15.73 15.73

C 12mm diameter holding down bolt, 300mm long including grouting

No 9.00 9.00 9.00 9.00 9.00

Mild steel galvanised bolt complying with BS 4190 including head, nut and washer

D 12mm diameter grade 8.8 black bolt, ne 75mm long

No 2.40 2.40 2.40 2.40 2.40

E 12mm diameter grade 8.8 black bolt, 75 - 150mm long

No 3.03 3.03 3.03 3.03 3.03

F 12mm diameter holding down bolt, 300mm long including grouting

No 10.07 10.07 10.13 10.13 10.13

4 WINDOWS

4.1 Casements and Sashes

Dark coloured anodised aluminium section frames in single light, complete with ironmongery, fixing straps, vinyl weather strips including building-in and pointing frame (glass measured separately)

A side-hinged window and casement frames m2 277.17 277.17 279.83 279.83 280.63B top-hung window frame and sash m2 277.17 277.17 278.80 278.80 279.97C sliding window frame and sash m2 251.23 251.23 252.57 252.57 253.40D fixed window frame m2 230.88 230.88 232.10 232.10 232.90

Page 17/34

ITEM DESCRIPTION UNIT 2010Q1 MEAN

2010Q2 MEAN

2010Q3 MEAN

2010Q4 MEAN

2011Q1 MEAN

4.1 Casements and Sashes

Natural anodised aluminium section frames in single light, complete with ironmongery, fixing straps, vinyl weather strips including building-in and pointing frame (glass measured separately)

E side-hinged window and casement frames m2 213.83 213.83 214.90 214.90 215.67F top-hung window frame and sash m2 214.20 214.20 215.27 215.27 216.03G sliding window frame and sash m2 199.96 199.96 200.90 200.90 201.50H fixed window frame m2 167.19 167.19 167.73 167.73 168.23

4.2 Louvre Window Frames

Dark coloured anodised aluminium adjustable louvre window frame complying with SS 212 including 6mm thick clips

A set of frame with single control m 41.50 41.50 41.50 41.50 41.50B set of frame with dual control m 43.90 43.90 43.90 43.90 43.90

4.3 Shopfront

Supply and fix aluminium shopfront frame complete with 10mm thick tinted float glass and fixing accessories, ironmongeries

A generally m2 330.53 330.53 330.53 330.53 330.53

Supply and fix aluminium shopfront frame complete with 12mm thick tempered tinted glass and fixing accessories

B generally m2 382.50 382.50 382.50 382.50 382.50

4.4 Cladding

Supply and fix dark coloured anodised aluminium frame complete with all necessary fixing accessories

A 670mm overall girth as cladding to concrete post

m2 267.50 267.50 267.50 267.50 268.97

B 390mm overall girth as sill m2 276.08 276.08 276.08 276.08 277.73C 560mm overall girth as blind pelmet m2 276.08 276.08 276.08 276.08 277.73

5 DOORS

5.1 Door Frames

Welded pressed galvanised steel rebated door frame to suit 110mm wall complying with BS 1245

A 1.2mm thick m 37.37 37.37 37.37 37.37 37.40

Page 18/34

ITEM DESCRIPTION UNIT 2010Q1 MEAN

2010Q2 MEAN

2010Q3 MEAN

2010Q4 MEAN

2011Q1 MEAN

5.2 Roller Shutter

Manually operated roller shutter constructed of zincalume and colorbond finished sheet steel panel curtain permanently lock-seamed and wrapped around drum assembly with extruded aluminium section, bottom rail including PVC weather seal and ironmongery

A generally m2 316.67 318.37 318.37 318.37 320.00

Motor operated roller shutter constructed of zincalume and colorbond finished sheet steel panel curtain permanently lock-seamed and wrapped around drum assembly with extruded aluminium section, bottom rail including PVC weather seal and ironmongery

B generally m2 563.33 566.67 566.67 566.67 560.00

5.3 Metal Fire Doors

1/2 hour rated steel fire door complying with SS 332 complete with fire proofed cylinder lockset, stainless steel ball bearing hinges, flush bolt, door closer and frame

A 1100 x 2150mm high No 1,078.77 1,111.53 1,111.53 1,111.53 1,111.53B 1100 x 2150mm high complete with approved No 1,170.48 1,204.33 1,204.33 1,204.33 1,204.33

6.35mm thick clear glass vision panel 600 x 125mm high

1 hour rated steel fire door complying with SS 332 complete with fire proofed cylinder lockset, stainless steel ball bearing hinges,flush bolt,door closer and frame

C 1200 x 2100 x 47mm thick, single leaf No 1,253.31 1,228.40 1,228.40 1,228.40 1,228.40D 2400 x 2100 x 47mm thick, double leaf No 2,583.83 2,532.40 2,532.40 2,532.40 2,532.40

2 hour rated steel fire door complying with SS 332 complete with fire proofed cylinder lockset, stainless steel ball bearing hinges, flush bolt, door closer and frame

E 1200 x 2100 x 48mm thick, single leaf No 1,353.71 1,400.40 1,400.40 1,400.40 1,400.40F 1800 x 2650 x 48mm thick, double leaf No 2,670.37 2,758.77 2,758.77 2,758.77 2,758.77G 2400 x 2100 x 48mm thick, double leaf No 2,825.08 2,918.50 2,918.50 2,918.50 2,918.50

4 hour rated metal fire and acoustic doorsH 900 x 2090mm high, single leaf No 2,857.01 2,950.50 2,950.50 2,950.50 2,950.50I 1800 x 2400mm high, double leaf No 6,486.47 6,691.40 6,691.40 6,691.40 6,691.40

Page 19/34

ITEM DESCRIPTION UNIT 2010Q1 MEAN

2010Q2 MEAN

2010Q3 MEAN

2010Q4 MEAN

2011Q1 MEAN

6 BALUSTRADES AND HANDRAILS

6.1 Stainless Steel

900mm stainless steel glass balustrades comprising 75mm diameter tubular top rail, 20mm vertical flat bars and 12mm thick etched pattern tempered glass panels fixed to balusters with stainless buttons with bottom ends of baluster cast into concrete

A horizontal balustrades m 856.00 860.00 856.00 856.00 856.00B raking balustrades m 927.33 931.73 927.30 927.30 927.30

1200mm high balustrades comprising 100mm diameter tubular stainless steel hairline finish top rail and 12mm thick clear tempered glass infill panel complete with all necessary fixings and jointings

C horizontal balustrades m 1,316.00 1,322.10 1,316.00 1,316.00 1,316.00D raking balustrades m 1,397.17 1,403.63 1,397.17 1,397.17 1,397.17

950mm high balustrades comprising 75mm tubular satin finish stainless steel top rail with 20x40mm vertical frames welded to top rail at 1000 centres with 12mm thick tempered glass infill panels complete with all necessary fixings and jointings

E horzontal balustrades m 1,113.17 1,118.37 1,113.17 1,113.17 1,113.17F raking balustrades m 1,171.33 1,176.80 1,171.33 1,171.33 1,171.33

6.2 Polished Stainless Steel

600mm high balustrades comprising 50mm diameter, two 20mm tubular intermediate and bottom rails with 32mm tubular balusters fixed with 100x100x6mm bearing plates at 800mm centres

A raking balustrades m 325.47 335.55 325.47 325.47 325.47

1000mm high balustrades comprising 65mm diameter tubular handrails and bottom rails both ends fixed with 150x150x6mm bearing plates with and including two 13mm diameter bolts with masonry anchors,38x4mm flat L shaped grid rails with 50x50x4mm triangular stiffener plates,50x6mm flat balusters at 1000mm centres fixed with 150x150x6mm bearing plates with and including two 13mm diameter bolts with masonry anchors fixed to concrete kerbs

B horizontal balustrades m 471.67 485.75 471.67 471.67 471.67

Page 20/34

ITEM DESCRIPTION UNIT 2010Q1 MEAN

2010Q2 MEAN

2010Q3 MEAN

2010Q4 MEAN

2011Q1 MEAN

6.3 Mild Steel

900mm high mild steel balustrades comprising 50mm diameter tubular handrails infilled with 20 x 6 thick top and bottom flat bars welded to 20mm diameter vertical sections including 20 x 6mm bar baluster

A raking balustrades m 134.67 135.33 135.33 135.33 135.33B horizontal balustrades m 131.00 131.67 131.67 131.67 131.67

1000mm high mild steel balustrades comprising 50mm diameter tubular handrails infilled with 20 x 6 thick top and bottom flat bars welded to 20mm diameter vertical sections including 20 x 6mm bar baluster

C raking balustrades m 123.33 124.00 124.00 124.00 124.00D horizontal balustrades m 120.33 121.00 121.00 121.00 121.00

1000mm high mild steel balustrades comprising 38x4mm flat core and bottom rails, 38x4mm flat L shaped grid rails with 50x50x4mm triangular stiffener plates, 50x6mm flat balusters at 1000mm centres

E horizontal balustrades m 116.74 116.74 116.74 116.74 116.74

7 PROPRIETORY DEMOUNTABLE PARTITIONS

7.1 Proprietory Toilet Cubicle

Supply & fix `Domo ZF' Series partition including fixing accessories

A single cubicle 1800mm wide No 1,913.95 1,913.95 1,913.95 1,913.95 1,913.95B range of two cubicles overall size

2000x1800mm deepNo 3,212.70 3,212.70 3,212.70 3,212.70 3,212.70

C range of three cubicles overall size 2700x1800mm deep

No 4,037.80 4,037.80 4,037.80 4,037.80 4,037.80D range of four cubicles overall size

3600x1800mm deepNo 5,012.97 5,012.97 5,012.97 5,012.97 5,012.97

E range of five cubicles overall size 4500x1800mm deep

No 6,703.98 6,703.98 6,703.98 6,703.98 6,703.98

`Moflex Carey' 10mm thick phenolic toilet partition/cubicle in selected colour complete with accessories

F generally m2 251.78 251.78 251.78 251.78 251.78

7.2 Proprietory Partition

`Huppe' Variplan system sliding and folding partition of double shell construction comprising laminated 13mm three-ply quality chipboard with individual lever spring mounted by plastic coated ball bearing rollers on aluminium ceiling track supported on steel trusses, with vertical magnetic strips at meeting stile including all necessary framing and ironmongery

A 8800x3600mm No 32,654.40 32,654.40 32,654.40 32,654.40 32,654.40

Page 21/34

ITEM DESCRIPTION UNIT 2010Q1 MEAN

2010Q2 MEAN

2010Q3 MEAN

2010Q4 MEAN

2011Q1 MEAN

7.2 Proprietory Partition

`Huppe' Variflex 100U mechanically operated wall system of steel and aluminium cavity frames including all necessary framing and ironmongery

B 8800x3600mm No 39,162.43 38,533.95 39,162.43 39,162.43 39,162.43

Styroplast partitions including all necessary stop ends, angles and intersections

C 50mm partition m2 56.13 56.13 56.13 56.13 56.13

8 SUNDRY

8.1 Surface Treatment

Hot dip galvanising complying with SS 117 to structural steelwork

A generally m2 5.61 5.61 5.61 5.61 5.62

Page 22/34

ITEM DESCRIPTION UNIT 2010Q1 MEAN

2010Q2 MEAN

2010Q3 MEAN

2010Q4 MEAN

2011Q1 MEAN

VII WALL AND CEILING FINISHES

1 IN-SITU FINISHES

1.1 Smooth Finished Plaster

Cement and sand (1:4) plaster mixed with mortar plasticiser to concrete or brick surface including trowelling smooth

A 6mm thick m2 10.67 10.83 11.73 11.73 11.73B 13mm thick m2 13.75 14.43 15.38 15.38 15.38C 20mm thick m2 17.08 17.78 18.95 18.95 18.95

1.2 Screed Backing

Cement and sand (1:3) screeded backing to concrete or brick surface to receive tiling

A 13mm thick m2 12.20 12.83 13.63 13.63 13.70B 20mm thick m2 14.85 15.50 16.50 16.55 16.63

1.3 Aggregate Plaster

Granite aggregate plaster consisting of cement and granite chippings (1:2) with mortar plasticiser to concrete or brick surface including scrubbing to produce exposed aggregate finishA 20mm thick m2 25.50 25.50 26.47 26.67 26.67

B 25mm thick m2 26.00 26.00 26.93 27.00 27.00

2 TILE FINISHES

2.1 Labour

Supply labour and mortar for laying homogenous tiles to wall including pointing with coloured cement

A generally m2 26.63 27.63 28.13 28.13 28.63

Supply labour and compatible adhesive for laying layng tiles to wall including pointing with coloured cement

B generally m2 31.20 32.13 32.63 32.63 32.88

3 STONE FINISHES

3.1 Labour

Supply labour and mortar for laying granite slabs including pointing with coloured cement

A generally m2 66.38 66.38 67.63 67.63 67.63

Supply labour and mortar for laying marble slabs includng pointing with coloured cement

B generally m2 66.88 66.88 68.13 68.13 68.13

Unit Rates - Wall and Ceiling FinishesLast Updated on 13/05/11

[The data will be updated on a quarterly basis]

Page 23/34

ITEM DESCRIPTION UNIT 2010Q1 MEAN

2010Q2 MEAN

2010Q3 MEAN

2010Q4 MEAN

2011Q1 MEAN

4 SHEET FINISHES

4.1 Labour

Supply labour and compatible adhesive for fixing decorative fabric or vinyl paper to wall including cutting border strips, corners and motifs to profile

A generally m2 4.30 4.30 4.30 4.30 4.33

5 SUSPENDED CEILINGS

5.1 Metal Framed Ceilings (Exposed Grid)

Exposed grid type suspended ceiling comprising galvanised steel suspension tees with aluminium flanged cappings arranged in grid including 6mm diameter steel rod hangers, clips and rivetting to all ends of grids along the boundaries

A 16mm thick Armstrong `Minaboard Tegular' mineral fibre board

m2 29.51 29.32 29.32 29.33 29.33

B 19mm thick Armstrong`Second Look Cortega' acoustical mineral fibre board

m2 31.37 31.05 31.05 31.50 31.50

C 6mm thick calcium silicate board m2 31.21 31.22 31.22 31.22 31.00D 12mm thick calcium silicate board m2 37.31 37.32 37.32 37.32 37.00E 6mm thick cement building board m2 29.29 29.28 29.28 29.28 29.28F 12mm thick cement building board m2 41.33 41.33 41.33 41.33 41.33G 10mm thick fibrous gypsum board m2 29.81 29.63 29.63 29.63 29.83H 16mm thick fibrous gypsum board m2 36.78 36.55 36.55 36.55 36.67I 8mm thick plain plasterglass board m2 36.84 36.83 36.83 36.83 36.83J 16mm thick Aflco randomed fissured

fibreglass ceiling panelm2 23.06 23.07 23.07 23.07 23.07

5.2 Metal Framed Ceilings (Concealed Grid)

Recessed grid type suspended ceiling comprising galvanised steel suspension tees with aluminium flanged cappings arranged in grid including 6mm diameter steel rod hangers,clips and rivetting to all ends of grids along the boundaries

A 16mm thick Armstrong `Minatone Fissured' mineral fibre board

m2 36.97 36.77 36.77 36.83 36.83

B 19mm thick Armstrong `Travertone Sanserra' acoustical mineral fibre board

m2 38.68 38.45 38.45 38.50 38.50

C 12mm thick fibrous qypsum board m2 34.65 34.45 34.45 34.45 34.33D 16mm thick fibrous gypsum board m2 42.23 41.97 41.97 41.97 41.67

5.3 Timber Ceilings

Ceiling board nailed, pinned or screwed to and including 50x50mm pressure impregnated kapur frames at 600mm centres bothways and hangers

A 12mm thick fibrous gypsum board,including pointing

m2 36.17 36.17 36.17 36.17 36.17

B 8mm thick plain plasterglass board m2 41.50 41.50 41.50 41.50 41.50

Page 24/34

ITEM DESCRIPTION UNIT 2010Q1 MEAN

2010Q2 MEAN

2010Q3 MEAN

2010Q4 MEAN

2011Q1 MEAN

5.3 Timber Ceilings

`Celotex' Hytone baroque or other equal and approved non-combustible random fissured mineral fibre board ceiling of panel size

C 600 x 1200 x 19mm thick m2 27.30 27.30 27.30 27.30 27.30

Suspended fibrous plasterboard ceiling with sealed joints fixed to & including suspension system

D 12mm thick m2 35.74 35.74 35.74 35.74 35.73E 19mm thick m2 43.77 43.77 43.77 43.77 43.83

5.4 Metal Ceilings

Linear metal suspended ceiling with chromated and stove enamelled finishes including galvanised steel runners, hangers,adjustment clips and fixing accessories

A Luxalon type 84C aluminium perforated linear ceiling

m2 78.59 78.59 78.59 78.67 78.67

B `Luxalon' lineal strip suspended ceiling system m2 82.65 82.65 82.65 82.65 82.67

C 101x0.6mm thick `Luxalon Type V100' aluminium screen ceiling

m2 79.71 79.71 79.71 79.71 79.67

D 0.6mm Dampa 200 type perforated aluminium strip ceiling

m2 79.82 79.82 79.82 80.12 80.12

Page 25/34

ITEM DESCRIPTION UNIT 2010Q1 MEAN

2010Q2 MEAN

2010Q3 MEAN

2010Q4 MEAN

2011Q1 MEAN

VIII FLOOR FINISHES

1 IN-SITU FINISHES

1.1 Plain Paving

Cement and sand (1:3) paving including trowelling smooth

A average 20mm thick m2 10.68 11.35 11.98 12.03 12.08B average 25mm thick m2 12.15 12.83 13.55 13.63 13.68C average 32mm thick m2 13.13 13.83 14.53 14.60 14.68D average 38mm thick m2 14.03 14.73 15.48 15.60 15.65E average 50mm thick m2 17.35 18.13 19.00 19.20 19.28F add or deduct each 10mm thickness m2 1.52 1.52 1.52 1.52 1.52

1.2 Waterproofed Paving

Waterproofed cement and sand (1:3) paving with Sika `No 1' waterproofing compound or equivalent including trowelling smooth

A average 20mm thick m2 14.17 14.20 15.20 15.20 15.23B average 25mm thick m2 16.07 16.13 17.23 17.23 17.27C average 32mm thick m2 16.80 16.87 17.80 17.80 17.87D average 38mm thick m2 17.87 17.93 18.93 18.93 19.00E average 50mm thick m2 20.73 20.80 22.10 22.10 22.17

1.3 Hardened Paving

25mm thick cement and sand (1:3) paving mixed with hardener including trowelling smooth

A light duty metallic hardener (0.25kg of hardener per kg of cement)

m2 17.17 17.17 17.83 17.83 17.87

B heavy duty metallic hardener (0.5kg of hardener per kg of cement)

m2 22.73 22.73 23.50 23.50 23.53

50mm thick cement and sand (1:3) paving mixed with hardener including trowelling smooth

C light duty non- metallic hardener (0.25kg of hardener per kg of cement)

m2 18.21 18.21 18.67 18.67 18.67

D heavy duty non-metallic hardener (0.5kg of hardener per kg of cement)

m2 24.58 24.58 25.17 25.17 25.17

E 3 coats Lapidolith hardener m2 35.69 35.69 35.97 35.97 35.97F Granolith non-metallic hardener m2 36.58 36.58 36.89 36.89 36.89G `Mastercon' premixed non-metallic hardener m2 29.94 29.94 30.16 30.16 30.16H prepare & apply `Korodor 04' floor hardener

power trowelled smooth and finish with one spray coat of `Korotex' curing compound internally

m2 38.35 38.35 38.71 38.71 38.71

I A-H Silica Quartz hardener m2 44.84 44.84 45.10 45.10 45.10

Unit Rates - Floor FinishesLast Updated on 13/05/11

[The data will be updated on a quarterly basis]

Page 26/34

ITEM DESCRIPTION UNIT 2010Q1 MEAN

2010Q2 MEAN

2010Q3 MEAN

2010Q4 MEAN

2011Q1 MEAN

1.4 Granolithic Paving

Granolithic aggregate paving consisting of cement,sand and granite chippings of 5mm gauge (2:1:5) set out in panels with 15x15mm deep recessed joints laterally at 1.20m centres including scrubbing to produce exposed aggregate finish

A 25mm thick m2 37.23 37.00 37.50 37.57 37.57B 32mm thick m2 38.34 38.11 38.61 38.78 38.78C 40mm thick m2 38.70 38.45 38.95 39.15 39.15D 50mm thick m2 46.46 46.16 46.66 46.80 46.80

1.5 Screed Bed

Cement and sand (1:3) screed to receive floor finishes

A 13mm thick m2 8.96 9.56 10.10 10.15 10.15B 20mm thick m2 10.42 11.07 11.73 11.75 11.75C 25mm thick m2 10.98 11.63 12.28 12.35 12.35D 32mm thick m2 12.26 12.91 13.63 13.75 13.75E 38mm thick m2 12.81 13.46 14.23 14.48 14.48F 50mm thick m2 14.58 15.25 16.00 16.25 16.25G add or deduct each 10mm thickness m2 1.49 1.49 1.49 1.49 1.49

2 STONE FINISHES

2.1 Labour

Supply labour for laying slabs with and including pointing with coloured cement

A granite generally m2 66.25 66.25 67.25 67.25 67.25B marble generally m2 66.25 66.25 67.25 67.25 67.25

3 BRICK FINISHES

3.1 Brick Paving

Supply and lay brick-on-edge paving in standard size 215x102.5x65mm first quality red facing brick complying with SS103 in cement mortar (1:4) with mortar plasticiser including pointing in coloured cement

A generally m2 38.59 38.59 38.59 38.59 38.83

4 TILE FINISHES

4.1 Labour for Tiling

Supply labour and mortar for laying tiles including pointing in coloured cement

A floor and horizontal surface m2 28.28 28.28 28.33 28.33 28.67B skirting ne 150mm high m 7.02 7.02 7.02 7.02 7.33C skirting 150-300mm high m 13.63 13.63 13.63 13.63 13.83

Supply labour and compatible adhesive for laying tiles including pointing with coloured cement

D floor and horizontal surface m2 30.95 30.95 30.95 30.95 31.00E skirting ne 150mm high m 7.22 7.22 7.22 7.22 7.33

Page 27/34

ITEM DESCRIPTION UNIT 2010Q1 MEAN

2010Q2 MEAN

2010Q3 MEAN

2010Q4 MEAN

2011Q1 MEAN

4.1 Labour for Tiling

Supply labour and compatible adhesive for laying tiles including pointing with coloured cement

F skirting 150-300mm high m 10.38 10.38 10.72 10.72 10.83

5 GLASS BLOCKS

5.1 Floors

Supply and lay glass `Solaris' 190x190x95mm thick glass block including pointing with white cement

A generally m2 345.23 345.23 345.23 345.23 345.23

5.2 Walls

95mm `NEG' hollow glass blockA generally m2 310.58 310.58 310.58 310.58 310.58

80mm thick with 6mm galvanised mild steel rod reinforcement

B generally m2 299.39 299.39 299.39 299.39 299.78

6 VINYL FINISHES

6.1 Vinyl Tiles

Supply and lay vinyl tiles with and including compatible adhesive for laying vinyl finishes

A 300x300x3mm Armstrong m2 25.18 25.18 25.18 25.18 25.18B 305x305x2.4mm Armstrong `Imperial' m2 24.14 24.14 24.14 24.14 24.14C 300x300x3.2mm Armstrong `Excelon' m2 32.97 32.97 32.97 32.97 32.97D 300x300x4mm asbestos m2 - - - - -

6.2 Labour for Laying Tiles/Sheet

Supply labour and compatible adhesive for laying vinyl finishes including hot welding seam joints with matching welding cord and polishing

A PVC tiles m2 10.17 10.17 10.17 10.17 10.17B PVC sheet m2 11.55 11.55 11.55 11.55 11.55

7 CARPET FINISHES

7.1 Labour for Carpeting

Supply labour and compatible adhesive for laying carpet including foam rubber underlay and fixing at perimeter

A carpet tile m2 7.56 7.56 7.56 7.56 7.68B broadloom carpet m2 8.50 8.50 8.50 8.50 8.56

Page 28/34

ITEM DESCRIPTION UNIT 2010Q1 MEAN

2010Q2 MEAN

2010Q3 MEAN

2010Q4 MEAN

2011Q1 MEAN

8 SUNDRIES

8.1 Dividing Strip

Supply and fix 25mm high extruded aluminium dividing strip to receive edge of floor finish

A 2mm thick m 8.19 8.42 8.42 8.42 8.32B 3mm thick m 11.14 11.47 11.47 11.47 11.37C 4mm thick m 14.21 14.63 14.63 14.63 14.53

Page 29/34

ITEM DESCRIPTION UNIT 2010Q1 MEAN

2010Q2 MEAN

2010Q3 MEAN

2010Q4 MEAN

2011Q1 MEAN

IX GLAZING

1 STANDARD GLASS

1.1 In Panes

Obscured glass to timber or metal frameA 5mm thick m2 57.10 57.10 57.10 57.10 57.28B 6mm thick m2 62.19 62.19 62.19 62.19 62.51

Clear float glass to timber or metal frameC 5mm thick m2 39.74 39.81 40.24 40.24 40.74D 6mm thick m2 54.29 54.36 54.90 54.90 55.46E 8mm thick m2 61.65 61.75 62.45 62.45 63.18F 10mm thick m2 97.08 97.08 98.20 98.20 99.15G 12mm thick m2 118.52 118.70 119.97 119.97 121.17

Tinted float glass to timber or metal frameH 5mm thick m2 35.97 36.41 36.41 36.41 37.01I 6mm thick m2 47.31 47.85 47.85 47.85 48.48J 8mm thick m2 68.10 68.89 68.89 68.89 69.75K 10mm thick m2 134.25 134.25 134.25 134.25 135.97L 12mm thick m2 154.70 154.70 154.70 154.70 156.75

Clear laminated float glass to timber or metal frameM 6mm thick m2 99.97 99.66 100.22 100.22 100.22

N 8mm thick m2 124.46 124.46 125.17 125.17 125.17O 10mm thick m2 165.04 164.92 165.88 165.88 165.72P 12mm thick m2 185.21 186.06 187.16 187.16 187.16

Tinted laminated float glass to timber or metal frame

Q 5mm thick m2 94.45 94.45 95.03 95.03 94.93R 6mm thick m2 101.43 101.43 102.05 102.05 102.05S 8mm thick m2 125.39 125.39 126.17 126.17 126.00T 10mm thick m2 176.91 176.91 177.99 177.99 177.52U 12mm thick m2 197.54 197.54 198.76 198.76 198.63

Tempered glassV 12mm thick m2 210.59 210.59 210.59 210.59 205.52

Tinted wired glassW 6mm thick m2 145.61 145.14 145.14 145.14 145.44

1.2 In Louvres

Obscured glass with ends housed in grooves of timber frame or fixed to metal clips

A 100x5mm thick m 4.46 4.46 4.54 4.54 4.54B 100x6mm thick m 5.67 5.67 5.73 5.73 5.73C 150x5mm thick m 6.29 6.29 6.40 6.40 6.40D 150x6mm thick m 7.57 7.57 7.70 7.70 7.70

Clear float glass with ends housed in grooves of timber frame or fixed to metal clips

E 100x5mm thick m 4.05 4.05 4.05 4.05 4.06

Unit Rates - GlazingLast Updated on 13/05/11

[The data will be updated on a quarterly basis]

Page 30/34

ITEM DESCRIPTION UNIT 2010Q1 MEAN

2010Q2 MEAN

2010Q3 MEAN

2010Q4 MEAN

2011Q1 MEAN

1.2 In Louvres

Clear float glass with ends housed in grooves of timber frame or fixed to metal clips

F 100x6mm thick m 5.61 5.66 5.83 5.83 5.90G 150x5mm thick m 5.83 5.87 6.00 6.00 6.07H 150x6mm thick m 6.73 6.81 6.93 6.93 7.00

Tinted float glass with ends housed in grooves of timber frame or fixed to metal clips

I 100x5mm thick m 4.72 4.72 4.72 4.72 4.79J 100x6mm thick m 5.70 5.70 5.70 5.70 5.73K 150x5mm thick m 6.07 6.07 6.07 6.07 6.10L 150x6mm thick m 7.54 7.54 7.54 7.54 7.57

Georgian wired polished glass with ends housed in grooves of timber frame or fixed to metal clips

M 100x6mm thick m 14.82 14.82 14.82 14.82 14.82N 150x6mm thick m 22.27 22.27 22.27 22.27 22.27

1.3 In Panels/Doors

Clear float toughened glassA 6mm thick m2 94.46 94.46 95.59 95.59 95.59B 8mm thick m2 118.03 118.03 119.46 119.46 119.46C 10mm thick m2 142.64 142.64 144.47 144.47 144.47D 12mm thick m2 188.90 188.90 191.16 191.16 191.16

Tinted float toughened glassE 6mm thick m2 96.26 96.26 96.26 96.26 96.59F 8mm thick m2 125.47 125.47 125.47 125.47 125.60G 10mm thick m2 162.11 162.11 162.11 162.11 162.28H 12mm thick m2 205.09 205.09 205.09 205.09 205.29

2 SPECIAL GLASS

2.1 Mirrors

Polished plate glass mirror with copper backing plugged to wall including chromium plated mirror screws and felt washers

A 3mm thick clear mirror m2 86.72 86.72 86.72 87.12 88.12B 3mm thick tinted mirror m2 92.03 92.03 92.03 92.86 93.53C 6mm thick clear mirror m2 204.19 198.82 198.82 201.35 203.02D 6mm thick tinted mirror m2 201.96 201.96 201.96 203.79 205.46

Bevelling to straight or circular edges including internal mitres and scallops

E 8mm wide m 57.50 57.50 62.67 63.48 64.20F 10mm wide m 64.17 64.17 69.67 70.54 71.31G 12mm wide m 71.40 71.40 77.48 78.45 79.32

Page 31/34

ITEM DESCRIPTION UNIT 2010Q1 MEAN

2010Q2 MEAN

2010Q3 MEAN

2010Q4 MEAN

2011Q1 MEAN

X PAINTING

1 PAINT APPLICATION

1.1 General Surfaces

Painting concrete or plastered surface and the like

A two coats of cement paint m2 3.14 3.11 3.11 3.11 3.11B two coats of water repellant solution m2 3.21 3.14 3.14 3.14 3.14C one base coat of cement paint, one undercoat

and one finishing coat of acrylic emulsion paintm2 3.58 3.61 3.61 3.61 3.78

Painting concrete or plastered surface and the like

D one coat of anti-alkali sealer, one undercoat and one finishing coat of PVA based emulsion paint

m2 3.68 3.65 3.65 3.65 3.68

E one coat of oil based anti-alkali sealer, one undercoat and one finishing coat of acrylic emulsion paint

m2 4.63 4.63 4.63 4.63 4.65

F one coat of epoxy primer and one coat of polyurethane paint

m2 9.93 9.93 9.93 9.93 10.00

G one coat of latex primer and two finishing coats of alkyd semi-gloss enamel paint

m2 7.78 7.78 7.78 7.78 7.78

H one coat of metal primer and 2 coats of enamel paint

m2 8.48 8.48 8.48 8.48 8.49

I one undercoat and two finishing coats of gloss oil paint

m2 3.68 3.68 3.68 3.68 3.73

J one coat of primer sealer and three finishing coats of PVA based emulsion paint

m2 5.83 5.83 5.83 5.84 5.84

K one undercoat two finishing coats synthetic emulsion paint

m2 3.32 3.32 3.32 3.32 3.36

L two finishing coats of epoxy paint m2 12.40 12.40 12.40 12.40 12.54M one coat of primer sealer and two finishing

coats of emulsion paintm2 3.25 3.25 3.25 3.25 3.29

N spray applied two coats of `Flakeline 251' flake reinforced Bisphenol polyyester resin based lining

m2 96.13 96.13 96.13 96.13 96.13

O two coats of `Sandtex Matt' m2 12.71 12.71 12.71 12.71 12.71P one coat of primer sealer, one body texture

coat and one finishing coat of polyurethane finish

m2 10.82 10.82 10.82 10.82 11.00

Q one undercoat and two finishing coats of weathershield emulsion

m2 5.92 5.92 5.92 5.92 5.75

R Lenaluck acrylic texture spray coating finishes m2 18.05 18.05 18.05 18.05 18.05

S one undercoat and two finishing coats of gloss enamel three coats of `Methalack-C' coating system

m2 42.98 42.98 42.98 42.98 42.98

Unit Rates - PaintingLast Updated on 13/05/11

[The data will be updated on a quarterly basis]

Page 32/34

ITEM DESCRIPTION UNIT 2010Q1 MEAN

2010Q2 MEAN

2010Q3 MEAN

2010Q4 MEAN

2011Q1 MEAN

1.1 General Surfaces

T one coat of plaster sealer, one undercoat and two coats of solvent based acrylic coating

m2 3.91 3.91 3.91 3.91 3.94

U one undercoat and one finishing coat with transparent clear coating of `Cemetex' glazed coating

m2 3.36 3.36 3.36 3.36 3.36

1.2 Timber Surfaces

Painting timber surfacesA two coats of aluminium wood primer m2 7.36 7.36 7.36 7.36 7.36B two coats of wood preservative painting

wrought woodwork surfacem2 3.36 3.36 3.36 3.36 3.36

C two coats of stain and two coats of wax polish m2 5.45 5.45 5.45 5.45 5.45

D two coats of varnish m2 10.20 10.20 10.20 10.20 10.43

Painting timber surfacesE one coat of aluminium wood primer, one

undercoat and two finishing coats of synthetic enamel paint

m2 9.10 9.10 9.10 9.10 9.10

F one coat of stain and three coats of clear polyurethane

m2 9.63 9.63 9.63 9.63 9.63

G two coats staining, varnishing three coats of translucent finish on wood

m2 10.10 10.10 10.10 10.10 10.10

1.3 Metal Surfaces

Painting on metal surfaceA two coats of aluminium paint m2 4.08 4.08 4.08 4.08 4.11B one undercoat and two finishing coats of

synthetic enamel paintm2 8.56 8.56 8.56 8.56 8.73

C two coats of zinc chromate primer, one undercoat and two finishing coats of synthetic enamel paint

m2 10.06 10.20 10.20 10.20 10.30

D one coat of intergard EPA 500/EPA 5001 anti-corrosive primer, one undercoat of intergard EPA 003/EPA 746 Mastic Mio aluminium and one recoatable finishing coat of series/PQA 015 or other similar approved paint

m2 45.74 45.74 45.74 45.74 45.74

1.4 Weldmesh Surfaces

Painting on both sides of weldmesh (measured flat on one side)

A two coats of aluminium paint m2 9.54 9.54 9.54 9.54 9.56B one undercoat and two finishing coats of

synthetic enamel paintm2 14.13 14.13 14.13 14.13 14.18

C two coats of zinc chromate primer, one undercoat and two finishing coats of synthetic enamel paint

m2 - - - - -

1.5 Cast Iron Pipe Surfaces

Knot and apply two coats of aluminium primer, one undercoat and two finishing coats of synthetic enamel paint

A small pipe m 2.33 2.33 2.33 2.71 2.54B large pipe m 2.84 2.84 2.84 3.38 3.51

Page 33/34

ITEM DESCRIPTION UNIT 2010Q1 MEAN

2010Q2 MEAN

2010Q3 MEAN

2010Q4 MEAN

2011Q1 MEAN

1.6 Galvanised Pipe Surfaces

Two coats of zinc chromate primer, one undercoat and two finishing coats of synthetic enamel paint

A small pipe m 2.15 2.15 2.15 2.31 2.34B large pipe m 2.63 2.63 2.63 2.88 2.94

1.7 Copper Pipe Surfaces

One coat of etch primer, one undercoat and two finishing coats of synthetic enamel paint

A small pipe m 1.66 1.66 1.66 1.81 1.87B large pipe m 2.15 2.15 2.15 2.34 2.41

1.8 UPVC Pipe Surfaces

One coat of polyvinyl acetate primer, one undercoat and two finishing coats of synthetic enamel paint

A small pipe m 2.38 2.38 2.38 2.54 2.54B large pipe m 2.89 2.89 2.89 3.04 3.04

1.9 Fire Protection

Provide and spray vermiculite to general surface

A 13mm thick m2 22.58 22.58 22.58 22.58 23.25B 25mm thick m2 32.63 32.63 32.63 32.63 33.30C 50mm thick m2 42.94 42.94 42.94 42.94 43.94

GPG fire rating compoundD generally m2 - - - - -

Mandolite P20 2 hours fire protectionE beam girders m2 42.06 42.06 42.06 42.06 44.77

`Blobest-RS' 2 hours fire protectionF beam m2 42.06 42.06 42.06 42.06 44.77

2.0 Labour

Supply labour to prepare and apply paint onA concrete or plastered surface m2 1.24 1.26 1.26 1.26 1.26B timber surface m2 1.24 1.26 1.26 1.26 1.26C metal surface m2 1.24 1.26 1.26 1.26 1.26D large pipe surface m2 1.24 1.26 1.26 1.26 1.26E small pipe surface m2 1.24 1.26 1.26 1.26 1.26

Page 34/34