Beefcake
Beefcake
Beefcake
Thank you for purchasing a Harper Beefcake.
TO THE OWNER OR OPERATOR:
As with all Harper products, the Harper Beefcake has been developed through tough design and testing procedures to produce a machine that can be relied on. This manual gives assembly, oper-ating, and service information for models BC1000, BC1500, and BC2000. Please read and under-stand all instructional material included with the Beefcake and its components before assembling and operating the equipment.
A Beefcake cake feeder can present hazards to an operator who follows unsafe procedures in either the operation or maintenance of the unit. Therefore, SAFETY WARNINGS are presented at certain locations in the text.
SYMBOL: SAFETY WARNING!
MEANING: Failure to understand and obey this warning may result in injury to you or others. Whenever this symbol is used, please pay very close attention to the information presented, and make sure you fully understand. If you do not, contact your dealer or Harper Industries for clarifica-tion.
SAFETY WARNING!
All shields and guards must be in place for proper and safe operation of this equipment. Where they are shown removed in this manual, it is for purposes of illustration and instruc-tion only. Do not operate this equipment unless all shields and guards are in place.
Harper Industries, Inc. is continually striving to improve the design and performance of its products. We reserve the right to make changes in specifications and design without thereby incurring any obligation relative to previously manufactured products.
© 2019 Harper Industries, Inc.The Harper and Beefcake names are registered trademarks of Harper Industries, Inc. All other brand and product names are trade-
marks or registered trademarks of their respective companies.
1
Beefcake2
LIMITED WARRANTY
Harper Industries, Inc. (HII) warrants to each purchaser of a new Harper Beefcake from an authorized dealer or representative, that such equipment is free of manufacturer’s defects in workmanship and materials which appear while in normal service for a period of ONE YEAR commencing with delivery to the original user.
The obligation of HII under this warranty is expressly limited, at our option, to replacement or repair at a service facility designated by Harper Industries or at the manufacturing plant in Harper, KS. A part will be replaced after inspection discloses it to have been defective. This warranty does not apply to defects caused by damage or unreasonable use (includ-ing failure to provide reasonable and necessary maintenance, or by performing functions without genuine Harper Beefcake accessories) while in the possession of the consumer.
Warranty is limited to parts, labor and ground freight delivery of replacement parts. HII shall not be liable for the consequential damages of any kind, including but not limited to consequential labor costs or transportation charges in connection with replacement or repair of defective parts.
This warranty does not apply to parts subjected to misuse, abuse, alteration, improper or inadequate maintenance, or normal wear (including chains, augers).
Harper Industries makes no warranty with respect to trade accessories. They are subject to the warranties of their respective manufacturers.
ANY IMPLIED OR STATUTORY WARRANTIES, INCLUDING ANY WARRANTY OR MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE EXPRESSLY LIMITED TO THE DURATION OF THIS WRITTEN WARRANTY. HII makes no other ex-press warranty, nor is anyone authorized to make any on behalf of HII.
For further information please contact your nearest Harper Beefcake dealer.
Date of Purchase _________/_________/_________
Dealer’s Name ______________________________
Dealer’s Phone ______________________________
Serial Number _______________________________
Beefcake
Table of ContentsOPERATOR SECTIONTo the Owner or Operator............................................Warranty Statement......................................................Table of Contents..........................................................Specifications................................................................Feature Identification Agitator............................................................. Agitator Pin....................................................... Hopper Door Lift Handle................................... Actuator............................................................. Augers.............................................................. Chute................................................................ Mounting Holes/Bolts........................................ Motor................................................................. Hopper.............................................................. Hopper Door.....................................................
General Safety Guidelines Equipment and Controls................................... Guards and Shields.......................................... Replacement Parts........................................... Safety Decals.................................................... Hydraulics.........................................................
Installation.....................................................................
Operating Instructions Before Operating.............................................. Transporting...................................................... Operating Hydraulic BC........................................ Electric BC..........................................
Optional Door Operations Door Lifting Mechanism....................................
Optional Chute Operations Method 1 - Manual Chute Operations.............. Method 2 - Actuator..........................................
1234
4455555555
66666
7
88
88
9
1010
3
PARTS SECTIONStructure Cake Feeder Assy............................................. Cake Feeder Stand........................................... Auger & Trough Assy........................................ Lid & Frame Assy.............................................. Lift Handle & Latch/Drive Shield....................... Agitator Drive Assy............................................ Agitator Assy..................................................... Chute Extension Assy....................................... Cake Feeder Dummy Arms.............................. Drive Shield...................................................... Decals..............................................................
Hydraulic/Electric Hydraulic Drive................................................. Electric Drive..................................................... Hand Control & Harness.................................. Electrical Schematic...........................................
Optional Door Operation Options (Kicker)...................... Electric Actuator................................................ Light Bar Option................................................
1.11.21.31.41.51.61.71.81.9
1.101.11
2.12.22.32.4
3.13.23.3
Beefcake
Power Hydraulic Electric Motor - Leeson 3/4 hp
Capacity BC2000 - 46 cu. ft. - about 2000 lbs. w/ 3/4” range cubes or 900 lbs. of cotton seed
Dimensions BC2000 - Length: 80 in Width: 42 in Height: 50.3 in
Paint Durable 2-part Polyurethane
Augers Two 6 inch diameter augersLeft - 76 3/4 in longRight - 78 in long
Options - Electronic Actuator for chute- Kicker for chute door
NOTE: Following publication of this manual, certain changes in standard equipment and options may have occurred which would not be included in these pages. Your Harper dealer is the best source for up-to-date information.
Specifications
Feature Identification
AGITATOR
AGITATOR PIN
Agitator - when rotating, it keeps seed from bridging, and breaks up bunches before it is fed into the augers.
Agitator Pin - when inserted, the agitator is engaged. This should only be engaged when feeding cotton seeds.
4
Beefcake
Hopper Door Lift Handle - used to open the hopper from the ground.
Actuator* - raises and lowers the chute.
Augers - when rotating, push the feed out of the hopper and down chute.
Chute - made of rubber and can be raised for transport or lowered for distribution of feed.
Kicker* - when attached it allows the door for the feed to be held in an open position.
Mounting Holes/Bolts - for mounting the Beefcake to the flatbed.
Motor - is a Leeson 3/4 hp used to power the dual augers.
Hopper - has three options of capacity: 1000, 1500, or 2000 lb limits based on choice of BC.
Hopper Door - has a weather proof strip on the inside edge of door to keep moisture out.
Lift Handle - used to open hopper when on the bale bed.
* denotes optional attachments of the Beef-cake.
5
CHUTE
MOUNTINGBOLTS/HOLES
MOTOR
HOPPER
HOPPERDOOR
LIFTHANDLEHOPPER
DOORLIFT
HANDLE
KICKER*
AUGERS
ACTUATOR*
Beefcake
General Safety GuidelinesEquipment & Controls • Before operating this equipment, read and understand the Operator’s Manual. • Altering the unit in any way that ad- versely affects its safe operation, per- formance or durability will void the wa- rranty and may cause hazardous con- ditions. • Know the location and function of all controls and how to stop the equip- ment quickly in an emergency before you operate the unit. • Keep all bolts, screws and fittings tight to ensure safe operation of equipment. Guards & Shields • Keep all safety devices in place and in good operating condition. • Replace all worn, damaged, unusable, missing or lost safety shields and guards before operating unit.
Replacement Parts• Use genuine factory parts or parts with equivalent characteristics including: type, strength and material. • Replace locknuts and locking screws if they cannot be tightened without considerable resistance for several turns before they are completely tight. • If hardware is not secure, or if fasten- ers are over-tightened, equipment fail- ure may result posing possible safety hazards. • Use proper torque specifications for all fasteners when they are replaced.
SAFETY WARNING! Failure to use genuine factory parts may result in voiding of the warranty, product malfunction or possible injury.
Safety Decals • If safety related or instructional decals become illegible or are removed, re- place them immediately. • If parts are replaced, make sure all safety related or instructional decals are present before the equipment is operated again. • New decals may be obtained from your local Harper Dealer.
Hydraulics
To prevent serious injury or death:• Relieve pressure on system before repairing, adjusting or disconnecting any hydraulic hose or fitting.• Wear proper hand and eye protection when searching for leaks. • Use wood or cardboard instead of hands when looking for leaks.• Keep all hoses, fittings and compo- nents in good operating condition.• Do not use any type of heat or flame (welding, soldering, cutting torch, etc.) near pressurized hydraulic lines.
SAFETY WARNING!
HIGH-PRESSURE FLUID HAZARD!Escaping fluid under pressure can pen-etrate skin causing serious injury or death.
6
Beefcake
InstallationYou can use select Deweze Balebeds to lift your new Beefcake on to the bed or one of many other options as long as safety, precau-tion and common sense are used.
SAFETY WARNING! Keep any objects or body extremities from beneath the Beefcake when loading and do not stand under the feeder when it is raised.
Next, position the Beefcake into place so that you can mark on the flatbed floor the location of the mounting holes for attaching the Beef-cake. Mark (4) mounting holes for drilling, ro-tate the Beefcake to the back of your flatbed, and drill the (4) mounting holes.
Put the Beefcake back in place where you marked and drilled the mounting holes. Attach with either the (4) mounting bolts included in your purchase or your own preferred size of mounting bolt that can fit into the predrilled mounting points on the Beefcake.
The final step depends on whether you have purchased the hydraulic or electric motor ver-sion of the Beefcake.
For the hydraulic, connect the hydraulic hoses that are attached to the Beefcake to your bed’s hydraulic hookups located on the right side of the headache rack. There is a check valve pre-installed on your Beefcake. If by chance the augers do not run when activated, switch the hoses on the bed location. This will allow it to run correctly. There is also an electrical harness that will need positive and negative leads run from the feeder to the battery under the hood of the truck.
For the electric, attach the positive cable to the solenoid as depicted below, and run it to the positive end of the battery on the truck, and be sure to put the 200 Amp fuse on with the cable (this will protect the motor).
Also, If you prefer to operate either of the ver-sion (hydraulic or electric) from inside your truck, run the Beefcake controller to the inside of your truck.
Check Valve
Motor
MOUNTINGBOLTS/HOLES
7
Motor
Positive cablefrom solenoidto motor
Negative cablefrom truck battery
Positive cablefrom truck battery
Fuse 200 AmpBUSS MRBF-200
Switch wirecontroll harness
Solenoid
Power wirecontroll harness
Ground wire controll harness
Beefcake
Operating InstructionsBefore Operating• Inspect inside the hopper and around the chain drive for the augers for any foreign objects. If any are found remove it/them. • Be sure to check that all shields are in place and that all bolts or fasteners are tightened.
Transporting• When transporting the Beefcake, be sure that the hopper lid’s lift handle has the safety latch in place so that the lid does not rise during transport due to wind.
OperatingWhen feeding cotton seed, insert agitator pin, and for any other feed remove pin.See page 4 for location.
Hydraulic Powered Beefcake• Fill Beefcake with desired amount of feed or grain product.• Lower the rubber chute to feeding position.• Activate the hydraulic motor with the balebed’s remote.
Due to the check valve on this product, if it be-comes clogged or stalls, it cannot be reversed
to dislodge it. You must stop the feeder, shut of the units power, and disconnect the hydrau-lic hoses to relieve any pressure on the sys-tem before seeing to the problem.
SAFETY WARNING! Do not put hands into a plugged auger when there is pressure on the system. It can result in harm.
• Do not use the hopper for long term storage of feed. It could create a corrosive environment and cause unwarranted wear on your machine.
Electric Powered Beefcake• Fill Beefcake with desired amount of feed or grain product.• Lower the rubber chute to feeding position.• Activate the electric motor with the Beefcake’s remote.
*Only available with the chute actuator option otherwise this switch serves no purpose.
For Your InformationThe controller for the Beefcake is used in both the hydraulic and electric version of the feeder. Currently, the only difference is that the auger is activated differently between the two options. The electric uses the auger on/off switch on the Beefcake remote, and the hydraulic uses the flatbeds hydraulic function to activate the auger. Aside from the auger, everything else on the Beefcake remote is uni-versal.
Safety Latch Revolution CounterCounter Reset
Raise/Lower Chute*
Auger On/Off
System On/Off
8
Beefcake9
Optional Door OperationsMethod #1Door Lifting Mechanism and Operation
When it is in the closed position, it will create piles while operating. Where as if it is in the open position, it will create a row while operat-ing.
This is located on the right side of the chute as depicted by the image.
Method #2Kicker
The kicker is a great option for when you will always be making rows rather than piles with your feed.
CAUTION!Method #1 door option is shipped with Beefcake CE but should not be used while feeding cotton seed.
NOTE: USE ONLY ONE METHOD.
CAUTION! Using both optional methods at the same time will cause either the chain or actuator to fail.
Manual Chute and Door Operation
Changing the position of this spring holds the door OPEN or CLOSED
This spring holds the Chute either UP or DOWN
Door Lifting Bolt Mechanism and Operation
The spring holds the door shut.
As the lifting bolt goes through the lower half of its revolution.
The spring continues to hold tension on the door.
As the lifting bolt goes through the upper half of its revolution, lifting the door to its full open position and then lowering it back down.
Door Lifting Mechanism and Operation
With the manual door kicker installed
When the Chute is up the door is closed.
When the Chute is down the door is open.
Beefcake
Method #1Standard
This is located on the left side of the chute as depicted by the image.
This is used for transportation so that the chute is not damaged in any way due to protruding from the side of the truck.
Method #2Actuator
The actuator replaces the spring that holds the chute either an up or down position. It allows the operator to manage the chute from the comfort of the seat or whatever their location is. See page 7 for details on the switch for the actuator.
Optional Chute Operations
10
Manual Chute and Door Operation
Changing the position of this spring holds the door OPEN or CLOSED
This spring holds the Chute either UP or DOWN
Beefcake
PARTS
Beefcake
Beefcake
Table of ContentsPARTS SECTIONStructure Cake Feeder Assy............................................. Cake Feeder Stand........................................... Auger & Trough Assy........................................ Lid & Frame Assy.............................................. Lift Handle & Latch/Drive Shield....................... Agitator Drive Assy............................................ Agitator Assy..................................................... Chute Extension Assy....................................... Cake Feeder Dummy Arms.............................. Drive Shield...................................................... Decals..............................................................
Hydraulic/Electric Hydraulic Drive................................................. Electric Drive..................................................... Hand Control & Harness.................................. Electrical Schematic...........................................
Optional Door Operation Options (Kicker)...................... Electric Actuator................................................ Light Bar Option................................................
1.11.21.31.41.51.61.71.81.9
1.101.11
2.12.22.32.4
3.13.23.3
Beefcake1.1
Par
ts L
ist
DES
CR
IPTI
ON
PAR
T #
QTY
ITEM
Cla
mp,
Ade
l .75
w x
1.2
5id
x .4
06 H
ole
1020
746
1B
olt,
5/16
-18
X 0.
75 in
Car
riage
1100
205
2B
OLT
, 5/1
6-18
X 0
.75,
WIZ
FLA
NG
E11
0444
143
NU
T, 5
/16-
18 L
OC
K (N
YLO
N)
1106
036
4N
UT,
5/1
6-18
WIZ
FLA
NG
E11
0606
145
Bolt,
5/1
6-18
X 1
in C
arria
ge11
0871
16
Was
her,
5/16
Fla
t, La
rge
Dia
. 1-1
/4 Z
inc
1111
556
7S
CR
EW, 1
/4 X
1 T
EK S
ELF-
TAP
7105
867
8
3 15
4
1 6
8
8Se
e Li
d&
Fram
e As
sy
Seal
#10
0623
2000
--
20 ft
.
Hop
per
#
2000
--
2154
01
See
Auge
r&
Trou
gh A
ssy
Cak
e Fe
eder
Ass
embl
yC
otto
n Ed
ition
1/3/
2019
2
7
Beefcake1.2
Parts
Lis
tD
ES
CR
IPTI
ON
PAR
T #
QTY
ITE
MB
OLT
, 1/2
-13
X 1
, WIZ
FLA
NG
E11
0220
41
NU
T, 1
/2-1
3 W
IZ F
LAN
GE
1105
884
2W
eldm
ent,
Cak
e Fe
eder
Sta
nd, 2
017
2153
761
3
3
1
2
Cak
e Fe
eder
Sta
nd20
17
2/20
/201
7
Beefcake1.3
Par
ts L
ist
DES
CR
IPTI
ON
PAR
T #
QTY
ITEM
Lid
Sea
l, .5
0 x
.187
x 3
610
0613
3 ft
1W
ASH
ER, 3
/8" F
LAT
SAE
1101
556
2Bo
lt, 3
/8-1
6 X
1 in
Car
riage
1105
568
3BO
LT, 5
/8-1
1 X
4.5
1105
622
4N
UT,
5/8
-11
HEX
1105
972
5N
UT,
3/8
-16
LOC
K N
YLO
N IN
SER
T11
0618
86
WAS
HER
, 5/8
" FLA
T S
TAN
DAR
D11
0650
27
WA
SHE
R, 5
/8" L
OC
K11
0655
28
Spro
cket
, 401
7 Id
ler,
5/8
1420
133
9Sp
rock
et, D
S40
A24
x 1-
1/4
1420
161
10R
OLL
PIN
, 1/4
X 2
2001
501
11W
eldm
ent,
Hin
ge R
od, T
win
Doo
r, 20
1921
5411
112
Wel
dmen
t, Au
ger,
Left
Han
d, 6
x421
5337
113
Wel
dmen
t, Au
ger,
Rig
ht H
and,
6x4
2153
381
14W
eldm
ent,
Cak
e Fe
eder
Tro
ugh,
201
921
5408
115
Wel
dmen
t, C
hute
Doo
r, 20
1921
5409
116
Parts
Lis
tD
ESC
RIP
TIO
NPA
RT
#Q
TYIT
EMC
hain
, Rea
r, C
ake
Feed
er24
0008
117
Cha
in, #
40 R
olle
r, 38
Lin
ks14
0022
3.2
ft.C
onne
ctin
g LI
nk, #
40 C
hain
1400
231
Cha
in, D
rive,
Cak
e Fe
eder
, 201
724
0011
118
Cha
in, #
40 R
olle
r, 32
Lin
ks14
0022
2.7
ft.C
onne
ctin
g LI
nk, #
40 C
hain
1400
231
Offs
et L
ink,
#40
Cha
in14
0024
1SP
AC
ER, 1
.25
X .6
9 X
1.2
526
0165
119
Sens
or M
ount
, Fee
der
2604
701
20Fe
eder
Doo
r Arm
2605
281
21SP
AC
ER, 1
.25
X .6
9 X
2.3
826
0678
122
SPA
CER
, 1.2
5 X
.69
X .4
2606
791
23B
earin
g In
sert,
2.8
3, 1
.25"
ec
Lk41
0232
424
Flan
ge, 2
Hol
e41
0233
825
Key,
1/4
X 1
/4 X
1.2
5, U
nder
5100
892
26Se
tScr
ew, 5
/16-
18 X
0.5
5102
542
27Sp
ring,
1.2
8od
X 7
.0L
X .1
35 W
ire20
2121
128
Auge
r & T
roug
h As
sem
bly
2019
1/3/
2019
Beefcakeii 1.3
Cha
in R
outin
g
1
13
14
15 6
3
28
1216
27
2021
11
2425
26
4
719
9
17
10
26
62
25
24
253Au
ger &
Tro
ugh
Asse
mbl
y20
19
1/3/
2019
58
22
2318
Beefcake1.4
Parts
Lis
tD
ESC
RIP
TIO
NPA
RT
#Q
TYIT
EMLi
d Se
al, .
50 x
.187
x 1
9210
0613
16 ft
1B
olt,
5/16
-18
X 0.
75 in
Car
riage
1100
206
21-
1/4
SQ P
LUG
1103
132
3BO
LT, 3
/8 X
3/8
SH
OU
LDE
R S
HC
S11
0439
44
NU
T, 5
/16-
18 L
OC
K (N
YLO
N)
1106
0314
5W
ASH
ER, 5
/16"
FLA
T ST
AN
DAR
D11
0665
66
BO
LT, 3
/8 X
.625
SH
OU
LDE
R S
HC
S11
1070
47
Wel
dmen
t, Fe
eder
Lid
2153
341
8W
eldm
ent,
Lid
Hin
ge21
5335
19
Lid
Hin
ge, S
hort
2604
592
10Li
d H
inge
, Sid
e M
ount
2604
602
11
4
9
4
1
84
10
10
11
72
7
6
5
5
Lid
Fram
e
#20
00 -
- 21
5343
Lid
& Fr
ame
Asse
mbl
yC
otto
n Ed
ition
1/3/
2019
5
NO
TE:
#4 &
#7
Sho
ulde
r Bol
ts a
re D
iffer
ent L
engt
hs
3
Beefcake1.5
Par
ts L
ist
DE
SCR
IPTI
ON
PA
RT
#Q
TYIT
EMB
OLT
, 3/8
X 3
/8 S
HO
ULD
ER S
HC
S11
0439
18
NU
T, 5
/16-
18 L
OC
K (N
YLO
N)
1106
031
9W
ASH
ER, 3
/8" F
LAT
STA
ND
AR
D11
0676
110
Wel
dmen
t, Li
d Li
ft B
ar, E
xter
nal,
1000
& 1
500
2153
181
11W
eldm
ent,
Lid
Lift
Bar
, Ext
erna
l, 20
0021
5346
1**
*Li
d La
tch,
150
0 &
2000
2605
491
12Li
d La
tch,
100
026
0529
1**
CO
TTE
R P
IN, 1
/8 X
0.7
551
0249
213
CO
VER
, VIN
YL
.25
X 1
.5 X
4 G
RIP
9100
441
14
Parts
Lis
tD
ES
CR
IPTI
ON
PA
RT
#Q
TYIT
EM
Bol
t, 5/
16-1
8 X
0.75
in C
arria
ge11
0020
11
NU
T, 5
/16-
18 W
ING
1103
273
2B
OLT
, 5/1
6-18
X 0
.75,
WIZ
FLA
NG
E11
0444
23
NU
T, 5
/16-
18 W
IZ F
LAN
GE
1106
062
4W
ASH
ER
, 5/1
6" F
LAT
STAN
DA
RD
1106
653
5W
eldm
ent,
Shi
eld,
Fee
der,
2017
2153
791
6S
hiel
d Su
ppor
t26
0670
17
1411**
*
13
10
13
812 **
92
5 6 25
1
Lift
Han
dle
& L
atch
Driv
e S
hiel
d20
17
2/20
/201
7
7
3
4
Beefcake1.6
Par
ts L
ist
ITEM
QTY
PAR
T #
DES
CR
IPTI
ON
1.1
110
2118
Pin
, Loc
k .3
75 X
1.5
, R
nd W
ire1.
28
1100
69W
ASH
ER
, 5/1
6" F
LAT
SAE
1.3
111
0087
BO
LT, 5
/8-1
1 X
2.75
1.4
411
0155
WAS
HER
, 3/8
" FLA
T S
AE1.
54
1103
28BO
LT, 5
/16-
18 X
1 F
LT H
D S
KT1.
64
1105
56Bo
lt, 3
/8-1
6 X
1 in
Car
riage
1.7
111
0597
NU
T, 5
/8-1
1 H
EX1.
88
1106
03N
UT,
5/1
6-18
LO
CK
(NY
LON
)1.
94
1106
18N
UT,
3/8
-16
LOC
K N
YLO
N IN
SER
T1.
101
1106
50W
ASH
ER, 5
/8" F
LAT
STA
ND
ARD
1.11
111
0655
WA
SHE
R, 5
/8" L
OC
K
Parts
Lis
tIT
EMQ
TYPA
RT
#D
ESC
RIP
TIO
N1.
122
1108
71Bo
lt, 5
/16-
18 X
1 in
Car
riage
1.13
114
2012
Spro
cket
, 401
3 x
11.
141
1420
13S
proc
ket,
4017
Idle
r, 5/
81.
151
2154
02W
eldm
ent,
Bea
ring
Mnt
Pla
te, A
gita
tor D
rive
1.16
121
5406
Wel
dmen
t, A
gita
tor D
rive
Spro
cket
1.17
124
0012
Cha
in, D
rive,
Cot
ton
Seed
Agi
tato
r1.
181
2420
08St
ub S
haft,
Agi
tato
r Driv
e1.
191
2420
09S
proc
ket,
40B
24 x
1-1
/4, A
gita
tor D
rive
1.20
226
0679
SPA
CER
, 1.2
5 X
.69
X .4
1.21
126
0745
Bear
ing
Supp
ort,
Agita
tor D
rive
1.22
141
0232
Bear
ing
Inse
rt, 2
.83,
1.2
5" e
c Lk
1.23
441
0233
Flan
ge, 2
Hol
e1.
241
5101
74G
REA
SE Z
ER
K, 1
/4-2
8 S
T1.
251
5102
28KE
Y, 1
/4 X
1/4
X 1
.0 U
ND
ER
1.3
1.6
1.10
1.15
1.2
1.8
1.16
1.20
1.14
1.11 1.
7
1.91.4
1.23
1.221.23
1.21
1.8
1.2
1.6
1.17
1.25
1.13
1.1
1.5
1.18
1.19
Not
e:Th
is B
earin
gD
oes
Not
Use
Lock
ing
Col
lar
1.12
Agita
tor D
rive
Asse
mbl
yC
otto
n Ed
ition
3/11
/201
9
1.24
Beefcake1.7
Par
ts L
ist
DES
CR
IPTI
ON
PAR
T #
QTY
ITE
MW
ASH
ER
, 5/1
6" F
LAT
SAE
1100
698
1.1
NU
T, 5
/16-
18 L
OC
K (N
YLO
N)
1106
038
1.2
CLA
MP
, 1 3
/4" E
XH
AUST
1107
574
1.3
Bolt,
5/1
6-18
X 1
in C
arria
ge11
0871
81.
4B
earin
g, 5
2mm
Sph
eric
al O
.D.,
1.0
I.D.,
Ecc
Loc
k14
2018
21.
5Fl
ange
, 52m
m, 2
Bol
t14
2019
41.
6W
eldm
ent,
Bear
ing
Mnt
Rig
ht, A
gita
tor S
haft
2154
031
1.7
Wel
dmen
t, B
earin
g M
nt L
eft,
Agita
tor S
haft
2154
041
1.8
Wel
dmen
t, A
gita
tor S
haft
2154
051
1.9
Bear
ing
Shi
eld
2607
501
1.10
Agita
tor,
Dis
char
ge P
late
2607
512
1.11
SC
RE
W, 1
/4 X
1 T
EK S
ELF
-TA
P71
0586
41.
12
1.8
1.12
1.4
1.1
1.2
1.6
1.5
1.6
1.9
1.7
1.10
1.4
1.1
1.2
1.6
1.5
1.6
1.4
1.1
1.2
Agita
tor A
ssem
bly
Cot
ton
Editi
on
1.11 1.3
1.11
2/20
/201
9
Dis
char
ge P
addl
es90
° to
Each
Oth
er
Use
Blu
eLo
ctite
Beefcake1.8
Pro
xim
ityS
enso
rP
art #
2350
27
Par
ts L
ist
DE
SCR
IPTI
ON
PA
RT
#Q
TYIT
EMW
ASH
ER
, 5/1
6" F
LAT
SAE
1100
692
1B
olt,
1/4-
20 X
0.7
5 in
Car
riage
1101
544
2B
OLT
, 3/8
X 1
/2 S
HO
ULD
ER
SH
CS
1102
892
3N
UT,
1/4
-20
WIZ
FLA
NG
E11
0290
14
Bolt,
1/4
-20
X 1
in C
arria
ge11
0326
25
BO
LT, 1
/4-2
0 X
.75
1105
614
6N
UT,
5/1
6-18
LO
CK
(NY
LON
)11
0603
27
NU
T, 1
/4-2
0 LO
CK
(NYL
ON
INS
ER
T)11
0630
108
BOLT
, 5/1
6 X
1.5
SH
OU
LDE
R S
HC
S11
0767
19
WA
SH
ER
, 1/4
" X 1
" OD
, Pla
in11
1033
410
Spr
ing,
1.0
6od
X 1
2L X
.135
Wire
2020
881
11FR
ICTI
ON
WA
SHE
R 1
.5"
2117
472
12S
enso
r, Pr
oxim
ity, W
ith P
lug
2350
271
13R
ubbe
r Chu
te26
0473
114
Chu
te E
xten
sion
2605
341
15C
hute
Ext
ensi
on, S
ide
Sup
port
2605
362
16C
hute
Ext
ensi
on, D
oubl
er P
late
2605
371
17
11
12
3
1
7 8
5
49
2
17
8
16
16
8 10 614
15
Chu
te E
xten
sion
Ass
embl
y20
17
2/20
/201
7
13
1/16
"
Beefcake1.9
Cake FeederDummy Arm
Bolt Kit # 205129
Front Half Back Half Front Half Back Half Front Half Back Half
675 215150 215353 215354 NA NA NA NA
676 215249 215353 215356 215355 215354 NA NA
677 215191 215353 215357 215355 215356 NA NA
679 215208 215353 215358 215355 215357 215355 215356
682 215145 215359 215357 215360 215356 NA NA
684 215193 215359 215358 215360 215357 215360 215356
687 215198 NA NA 215360 215361 215360 215361
688 215200 NA NA 215360 215362 215360 215362
778 215160 215363 215364 NA NA NA NA
776 215257 215363 215365 215367 215366 NA NA
782 215158 215363 215368 215367 215369 NA NA
784 215202 215363 215370 215367 215371 215367 215372
787 215204 NA NA 215367 215373 215367 215373
788 215206 NA NA 215367 215374 215367 215374
Cake Feeder Dummy Arms1000 1500 2000Flatbed
Model #Standard
Dummy Arm
DecalsModel # Part #
675 202095676 202096677 202097679 202098682 202099684 202100687 202101688 202102778 202105776 202104782 202106784 202107787 202108788 202109
Decals Must BePurchased Seperately
6/6/2018
Front Half Back Half
NOTAPPLICABLE
Beefcake1.10
Parts ListDESCRIPTIONPART #QTYITEM
Bolt, 5/16-18 X 0.75 in Carriage11002011NUT, 5/16-18 WING11032732
BOLT, 5/16-18 X 0.75, WIZ FLANGE11044423NUT, 5/16-18 WIZ FLANGE11060624
WASHER, 5/16" FLAT STANDARD11066535Weldment, Shield, Agitator Drive21540716
Shield Support26067017
17
43
25
6
5 2
Drive ShieldCotton Edition
1/3/2019
Beefcake1.11
Parts
Lis
tD
ESC
RIP
TIO
NPA
RT
#Q
TYIT
EMD
ecal
, Gua
rd R
emov
ed, G
raph
ic16
0002
11
DAN
GE
R D
EC
AL20
0010
12
Dec
al, D
ange
r, R
otat
ing
Auge
r20
2090
13
Dec
al, B
eefc
ake
& Bu
ll 21
.87
X 8
.75
2020
911
4D
ecal
, Dew
Eze,
11.
5 X
1.8
2020
921
5D
ecal
, Pin
stri
pe20
2093
16
Dec
al, C
otto
n Ed
ition
2021
351
7D
ecal
, Dan
ger K
eep
Cov
ers
In P
lace
5000
381
8
Dec
al P
age
Dew
Eze
BEE
FCAKE
Cotto
n Ed
ition
1/3/
2019
3
4 8
1
2
56
7
Beefcake2.1
Kit,
Hyd
Driv
e (1
4.1)
#20
5127
ITE
MQ
TYPA
RT
#D
ES
CR
IPTI
ON
12
1102
54B
OLT
, 7/1
6-14
X 1
.25,
WIZ
FLA
NG
E2
211
0337
NU
T, 7
/16-
14 W
IZ F
LAN
GE
34
1104
20B
OLT
, 3/8
-16
X 1
.04
111
0444
BO
LT, 5
/16-
18 X
0.7
5, W
IZ F
LAN
GE
53
1105
39B
OLT
, 7/1
6-14
X 1
.25
61
1106
06N
UT,
5/1
6-18
WIZ
FLA
NG
E7
311
0641
NU
T, 7
/16-
148
311
0670
WAS
HER
, 7/1
6" F
LAT
STA
ND
ARD
93
1106
71W
ASH
ER
, 7/1
6" L
OC
K10
411
0672
WA
SH
ER
, 3/8
" LO
CK
112
1202
45A
DA
PTE
R, 8
MJ-
10M
B90
121
1205
35Va
lve,
Che
ck, 8
fj-8m
j13
212
0582
Cou
pler
, Pio
neer
Mal
e, O
RB
142
1207
18A
dapt
er, 8
mb-
6fjx
9015
114
2017
Spr
ocke
t, 40
BS17
x 1
.016
222
0745
Hos
e, .3
75 x
36.
0 6-
8fjx
/6m
j17
126
0669
Driv
e M
ount
, Hyd
raul
ic18
126
0680
Hyd
raul
ic M
ount
Gus
set
191
4201
28M
otor
, Eat
on 1
01-1
014
(14.
1 C
I)**
*1
2220
62M
otor
, Eat
on 1
01-1
751
(7.3
CI)
1314
1314
16
1612
19 ***
17
13
10
2
18
46
11
11 58
97
15
For C
hain
Par
t #S
ee A
uger
& T
roug
h
2/20
/201
7
Hyd
raul
ic D
rive
2017
Low
Flo
w O
ptio
nK
it #2
0512
8Fo
r Use
With
Dew
Eze
Hea
vy D
uty
E/H
Beefcake2.2
Kit,
Elec
tric
Driv
e #2
0512
6D
ESC
RIP
TIO
NPA
RT
#Q
TYIT
EMBO
LT, M
8x1.
25 x
25
Gr 1
0.9
1102
605
1N
UT,
5/1
6-18
U-T
YPE
.75L
1103
192
2BO
LT, 3
/8-1
6 X
1.0
1104
202
3BO
LT, 5
/16-
18 X
0.7
5, W
IZ F
LAN
GE
1104
444
4B
OLT
, 7/1
6-14
X 1
.25
1105
393
5N
UT,
5/1
6-18
, UN
ITO
RQ
UE
LO
CK
1106
002
6N
UT,
7/1
6-14
1106
413
7W
ASH
ER, 5
/16"
FLA
T ST
AND
ARD
1106
652
8W
ASH
ER, 7
/16"
FLA
T ST
AND
ARD
1106
703
9W
ASH
ER, 7
/16"
LO
CK
1106
713
10W
ASH
ER, 3
/8" L
OC
K11
0672
211
WAS
HER
, 5/1
6" L
OC
K11
0674
512
Term
inal
Pro
tect
or, R
ed, 1
-2ga
1300
681
13Fl
ybac
k D
iode
Ass
embl
y, C
ake
Feed
er13
2163
114
Spro
cket
, 40B
S17
x 1.
014
2017
115
Batte
ry C
able
QC
, 2ga
Tw
in L
ead,
30"
2301
691
16So
leno
id, 4
Pos
t, 12
VDC
Con
tact
or23
2103
117
Mot
or, 1
2V D
C, 3
/4 H
P23
2110
118
Gea
r Red
ucer
, Inl
ine,
29.
4:1
2420
061
19D
rive
Mou
nt, E
lect
ric26
0668
120
Mot
or S
hiel
d, E
lect
ric, 2
017
2606
741
21C
able
, 4 g
a. 9
", R
ed53
2084
122
CLA
MP,
HO
SE
#88
6.00
"94
0028
123
Parts
Lis
tD
ESC
RIP
TIO
NPA
RT
#Q
TYIT
EMB
atte
ry C
able
QC
, 2ga
Tw
in L
ead,
216
"23
0168
11
Kit,
Beef
Cak
e Fu
se a
nd H
olde
r20
5137
12
FUS
E H
OLD
ER
, BU
SS
CFB
AR
1-M
8XSP
1320
931
2.1
FUSE
200
AM
P, B
USS
MR
BF-2
0013
2094
22.
2FU
SE
CO
VER
, BU
SS C
FCO
VER
-1R
1320
921
2.3
NU
T, M
8 X
1.25
WIZ
FLAN
GE
1101
411
2.4Fo
r Cha
in P
art #
See
Auge
r & T
roug
h
13
22
17
23
18
4
8
6
24
11
319
20
1215
910
7
15
3/5/
2019
Elec
tric
Driv
e20
17
SOLE
NO
ID
Sw
itch
Wire
Con
trol H
arne
ss
Fuse
200
Am
pBU
SS M
RBF
-200
Pos
itive
Cab
leFr
om T
ruck
Bat
tery
MO
TOR
Neg
ativ
e C
able
From
Tru
ck B
atte
ry
Pos
itive
Cab
leFr
om S
olen
oid
to M
otor
Gro
und
Wire
To S
olen
oid
Gro
und
Wire
Con
trol H
arne
ss
Pow
er W
ireC
ontro
l Har
ness
Flyb
ack
Dio
deH
arne
ss
16
1
2.3
2.4
2.1
2.2
14
Beefcake2.3
Han
d C
ontro
l Ass
y, P
art #
1500
47D
ESC
RIP
TIO
NP
AR
T #
QTY
ITEM
Cou
nter
, Dis
play
1321
291
1S
witc
h, R
ocke
r Min
. DPD
T, (O
n)-O
FF-(
ON
)13
2131
12
Sw
itch,
Roc
ker M
in. S
PS
T, O
n-O
FF, I
lum
.13
2132
23
TOP
HO
US
ING
, HA
ND
CO
NTR
OL
1500
011
4BO
TTO
M H
OU
SIN
G, H
AND
CO
NTR
OL
1500
031
5S
CR
EW
, #6
X 1/
4 TY
PE
F15
0013
46
SCR
EW
, #6
X 1
SH
EET
ME
TAL
1500
142
7S
CR
EW
, #6
X 1.
5 S
HEE
TME
TAL
1500
152
8S
witc
h P
late
, Fee
der,
Han
d C
ontro
l15
0046
19
Dec
al, C
ake
Feed
er H
and
Con
trol
2020
891
10C
able
, Han
d C
ontro
l, Fe
eder
2301
641
11
MA
STER
ON
/OFF
AU
GER
ON
/OFF
CH
UTE
UP
/ DN
RED
YELLOW
BLUE
GREEN
BROWN
BLACK
3 124
Han
d C
ontro
lFr
om B
acks
ide
CO
UN
TER
/D
ISP
LAY
31
2
2
13
NO
TE:
All 3
DIP
Sw
itche
s S
et to
ON
1321
323P
SP
ST
ON
-OFF
ILLU
M
Han
d C
ontro
l&
Har
ness
6 12
4 3
5
RE
DG
RE
EN
BR
OW
N
BLU
EY
ELL
OW
BLA
CK
2/20
/201
7
Pow
erG
roun
d Sw
itche
d
Beefcakeii 2.3
Pro
xim
ityS
enso
rPa
rt #2
3502
7
Chu
teAc
tuat
orP
art #
2350
28
AC
BBR
OW
N
BLA
CK
BLU
E1/
16"
21
WH
ITE
BLA
CK
Har
ness
Cak
e Fe
eder
Con
trol
Par
t #23
2112
Cak
e Fe
eder
Hyd
raul
icPa
rt #2
3211
4
Cak
e Fe
eder
Ele
ctric
Par
t #23
2113
To P
ositi
ve P
ost
Truc
k B
atte
ry
To N
egat
ive
Pos
tTr
uck
Bat
tery
To N
egat
ive
Pos
tA
t Mot
or
To P
ositi
ve P
ost
At S
olen
oid
To S
witc
h P
ost
On
Sol
enoi
d
To H
and
Con
trol
Han
d C
ontro
l&
Har
ness
2/20
/201
7
Spl
ice
into
PU
RP
LEW
ire o
n V
alve
Har
ness
Spl
ice
into
GR
AY
Wire
on
Val
ve H
arne
ss
Beefcake2.4
MA
STE
RO
N/O
FF
AU
GER
ON
/OFF
CH
UTE
UP
/ D
N
RED
YELLOW
BLUE
GREEN
BROWN
BLACK
3 124
Han
d C
ontro
lFr
om B
acks
ide
CO
UN
TER
/D
ISP
LAY
31
2
2
13
FUSE
BA
TTE
RY
Pow
er W
ire
Gro
und
Wire
Sw
itch
Wire
Pow
er W
ire
Gro
und
Wire
Spl
ice
Into
Pur
ple
Wire
Spl
ice
Into
Gra
y W
ire
Cak
e Fe
eder
Ele
ctric
al S
chem
atic
Pos
itive
SO
LEN
OID
Switc
h W
ireC
ontro
l Har
ness
Fuse
200
Am
pB
US
S M
RB
F-20
0
Pos
itive
Cab
leFr
om T
ruck
Bat
tery
MO
TOR
Neg
ativ
e C
able
From
Tru
ck B
atte
ry
Posi
tive
Cab
leFr
om S
olen
oid
to M
otor
Gro
und
Wire
To S
olen
oid
Gro
und
Wire
Con
trol H
arne
ss
Pow
er W
ireC
ontro
l Har
ness
Neg
ativ
e
Hyd
raul
icV
alve
Con
trol
Hyd
raul
ic D
rive
Pow
er S
uppl
y
Ele
ctric
Driv
eC
able
Hoo
kup
2/21
/201
7
Beefcake
Beefcake3.1
Par
ts L
ist
DE
SCR
IPTI
ON
PAR
T #
QTY
ITEM
Kit,
Bee
fCak
e M
anua
l Doo
r Kic
ker
2051
35
W
AS
HE
R, 5
/16"
FLA
T S
AE
1100
691
1W
ASH
ER
, 3/8
" FLA
T S
AE11
0155
12
NU
T, 5
/16-
18 L
OC
K (N
YLO
N)
1106
031
3N
UT,
3/8
-16
LOC
K N
YLO
N IN
SE
RT
1106
181
4Bo
lt, 3
/8-1
6 X
1.5
in C
arria
ge11
0916
15
BO
LT, 3
/8 X
1.0
SH
OU
LDE
R S
HC
S11
1071
16
Man
ual D
oor K
icke
r26
0463
17
Kit,
Bee
fCak
e B
all J
oint
2051
34
N
UT,
3/8
-24
1100
832
8W
ASH
ER, 3
/8" F
LAT
STA
ND
AR
D11
0676
19
Bolt,
3/8
-24
X 7
.011
1068
110
Ball
Join
t Lin
kage
, 3/8
-24
RH
1420
151
11
10
11
8
9
5
6
72
4
13
Doo
r Ope
ratio
n O
ptio
ns
Met
hod
One
Met
hod
Two
9/27
/201
7
2051
35
2051
34
Beefcake
Ele
ctric
Act
uato
r Opt
ion,
Par
t #23
5029
DE
SC
RIP
TIO
NPA
RT
#Q
TYIT
EM
NU
T, 1
/4-2
0 W
IZ F
LAN
GE
1102
902
1C
OTT
ER
PIN
, 3/3
2 X
0.7
511
0300
22
BO
LT, 1
/4-2
0 X
0.7
5, W
IZ F
LAN
GE
1104
682
3W
ASH
ER, 1
/4" F
LAT
STA
ND
AR
D11
0673
24
CLE
VIS
PIN
, STD
ZP
1/4
X 1
5/8
1120
952
5TO
OL
BO
X D
OO
R H
ING
E, O
UTE
R H
ALF
2116
591
6TO
OL
BO
X D
OO
R H
ING
E, I
NN
ER H
ALF
2116
601
7A
ctua
tor,
5.9"
, With
Plu
g23
5028
18
1
3
7
2
4
5
8
2
5
16
3
4
Ele
ctric
Act
uato
rO
ptio
n
10/4
/201
6
3.2
Beefcake3.3
Cak
e Fe
eder
Lig
ht B
ar O
ptio
n Pa
rt #
2051
42D
ESC
RIP
TIO
NPA
RT
#Q
TYIT
EMSe
al, .
50 x
.187
x 1
5610
0613
13 ft
.1
Cab
le T
ie, E
dge
Clip
, Top
Mou
nt, 7
.9" B
lack
1021
175
2PL
UG
, 1/2
" BU
TTO
N P
LAST
IC11
0753
63
SCR
EW, 1
0-24
X 3
/4 S
TAIN
LESS
PH
ILLI
PS
PAN
HEA
D11
0834
44
NU
T, 1
0-24
RIV
ET A
LUM
INU
M11
0835
45
GR
OM
ME
T, 9
/16
X 1"
OD
1500
181
6C
LAM
P, A
DEL
AC
10 .2
65 H
OLE
2000
193
7W
eldm
ent,
Ligh
t Bar
, Cak
e Fe
eder
2153
991
8LI
GH
T, 3
/4" R
OU
ND
, LE
D, R
ED23
2091
39
Gro
mm
et, 6
" Ova
l, G
rote
2321
252
10Li
ght,
Ova
l, S/
T/T,
Mal
e P
in, G
rote
2321
272
11H
arne
ss, C
ake
Feed
er L
ight
Bar
2321
421
12H
EAD
LIG
HT
ASSE
MBL
Y, F
LUS
H M
OU
NT
LED
8350
272
13SC
REW
, 3/1
6 X
.75
TEK
SE
LF-T
AP
7105
876
14
611
10
9
3
14
85
4
13
Cak
e Fe
eder
Ligh
t Bar
Opt
ion
The
Ligh
t Bar
Opt
ion
harn
ess
# 23
2142
plug
s di
rect
ly in
to th
e G
rote
har
ness
on y
our D
EWEZ
E fla
tbed
afte
r Jun
e 20
18.
If
you
are
putti
ng in
on
an o
lder
bed
you
will
need
to o
rder
the
Adap
ter H
arne
ss K
itpa
rt #
2350
33.
2/8/
2019
1
Wiri
ng H
arne
ssW
ill R
un A
long
Rig
ht S
ide
Then
Acr
oss
Hea
dach
e R
ack
and
Plug
Into
Plac
e of
Tai
l Lig
hts
7
Beefcake
NOTES
Beefcake
Harper Industries, Inc.151 E. Highway 160Harper, KS 67058
Website: www.harperindustries.com
Telephone: 620-896-7381Toll-Free: 800-835-1042Fax: 620-896-7129
E-mail: [email protected]