SPEC SHEET CATALOG
Ul t imat ion Indust r ies LLC
15935 Stu rgeon St.Rosev i l le, MI 48066
Ph. +1-586-771-1881
ul t imat ion inc.com
BELT CONVEYOR
Safety Orange110559RAL-2010
Machinery Grey 110652RAL-7011
Safety Blue110552RAL-5019
Conveyor Blue110549
Dark Green110555RAL-6005
Conveyor Gray Safety Yellow110554RAL-1023
Light Ivory 115174RAL-1015
Gloss Black111233RAL-9005(Textured black available)
Gloss White111232RAL-9003
Colors illustrated below may vary slightly from actual paint colors.
Standard Paint Colors
Conveyor Green115886
nAll safety guarding to be safety yellow unless
otherwise specified.
nOther items available, please contact factory.
nOther colors available on request
Dark Blue 114815
Light BlueRAL-5012
Sky BlueRAL-5015
48 HOUR
SHIP COLOR
Roseville, Michigan • Phone: (586) 771-1881 • www.ultimationinc.com
TABLE OF CONTENTSBELT CONVEYORS
Horizontal belt conveyor ............................................................... 1-8
Belt curve .........................................................................................9
Incline belt conveyor ..................................................................10-13
Incline dimensional chart ................................................................14
Bed and undertrussing information .................................................15
Troughed belt conveyor..............................................................16-19
LIVE ROLLER CONVEYORS
Belt driven live roller conveyor (transportation) ..........................20-21
Belt driven live roller conveyor (minimum pressure) ...................22-23
Belt driven live roller conveyor (zero pressure) ...................... 23A-23B
Flat motor conveyor (transportation) ..................................... 23C-23E
Flat motor conveyor (zero pressure) ...................................... 23F-23H
V-belt driven live roller conveyor (minimum pressure) ................24-39
Lineshaft conveyor .....................................................................40-43
Chain driven live roller conveyor (transportation) .......................44-54
CHAIN CONVEYORS
Drag chain conveyor (transportation) .........................................55-58
GRAVITY CONVEYOR
Skatewheel conveyor .................................................................59-61
Gravity roller conveyor ...............................................................62-72
Ball transfer table ...........................................................................73
Conveyor rail...................................................................................74
ACCESSORIES
Supports ....................................................................................75-78
Guide rails ......................................................................................79
Stops .........................................................................................80-82
Gates .........................................................................................83-84
ELECTRICAL CONTROLS
ProLogic Accumulation System ..................................................85-86
Roseville, Michigan • Phone: (586) 771-1881 • www.ultimationinc.com
1
BS100B
The BS100B belt conveyor is ideal for transporting packages of various sizes and shapes. It can be used in many types of material handling application such as assembly operations, sorting, packaging, and inspection or for simply transporting product from point A to B.
Note: A short belt segment laced on both ends, commonly called a “Dutchman”, is provided on conveyors 35 ft. to 70 ft. This allows for future belt stretch with a standard end take-up. An underside take-up or center drive with take-up is recommended for conveyors over 70 ft. long.
CONVEYOR WEIGHTS (LBS.)
OVERALL LENGTH
BED LENGTH
OVERALL LENGTH
WITH CENTER DRIVE
BELT WIDTH
6" 8" 10" 12" 14" 16" 18" 20" 24" 30"
BED WIDTH
10" 12" 14" 16" 18" 20" 22" 24" 28" 34"
6' 5' 6'
4 I
N.
DIA
. D
RIV
E P
ULLE
Y
220 236 252 268 284 300 316 332 363 403
11' 10' 11' 265 285 305 325 345 365 385 405 445 501
16' 15' 16' 300 324 348 372 395 419 443 467 514 588
21' 20' 21' 345 373 401 429 456 484 512 540 596 686
26' 25' 26' 380 412 444 476 506 538 570 602 665 773
31' 30' 31' 425 461 497 533 567 603 639 675 747 871
36' 35' 36' 463 502 541 580 619 658 697 736 816 958
41' 40' 41' 508 551 594 637 680 723 766 809 898 1,056
46' 45' 46' 543 590 637 684 730 777 824 871 967 1,143
51' 50' 51' 588 639 690 741 791 842 893 944 1,049 1,241
56-11" 55' 56'
8 I
N.
DIA
. D
RIV
E P
ULLE
Y
686 745 804 863 920 979 1,038 1,097 1,216 1,434
61-11" 60' 61' 731 794 857 920 981 1,044 1,107 1,170 1298 1,532
66-11" 65' 66' 769 835 901 967 1,033 1,099 1,165 1,231 1,367 1,619
71-11" 70' 71' 814 884 954 1,024 1,094 1,164 1,234 1,304 1,449 1,717
76-11" 75' 76' 849 923 997 1,071 1,144 1,218 1,292 1,366 1,518 1,804
81-11" 80' 81' 894 972 1,050 1,128 1,205 1,283 1,361 1,439 1,600 1902
86-11" 85' 86' 929 1,011 1,093 1,175 1,255 1,337 1,419 1,501 1,669 1989
91-11" 90' 91' 974 1,060 1,146 1,232 1,316 1,402 1,488 1,574 1,751 2087
96-11" 95' 96' 1,012 1,101 1,190 1,279 1,368 1,457 1,546 1,635 1,820 2,174
101-11" 100' 101' 1,057 1,150 1,243 1,336 1,429 1,522 1,615 1,708 1,902 2,272
n Smooth, slim design n Coped ends n 10 belt widths n Multiple belt options
STANDARD SPECIFICATIONS
BELT - Black Trackmate 120 EMB
BED - 4 in. deep x 12 ga. powder coated steel slider bed. Standard 5 ft. and 10 ft. long bolt-together sections with splice plates.
END DRIVE - Located on discharge end of conveyor. Chain guard is on left-hand side when standing at infeed looking toward discharge.
DRIVE PULLEY - 4 in dia. with 1 in. dia. shaft at bearings or 8 in. dia. with 1 7/16 in. dia. shaft at bearings. Machined, crowned and fully lagged.
TAIL PULLEY - 4 in. dia. with 1 in. dia. shaft at bearings. Machined crown.
SNUB ROLLERS - Adjustable 2 1/2 in. dia. rollers. Grease packed ball bearings. Includes guard.
RETURN ROLLERS - Adjustable 1.9 in. dia. rollers. Grease packed ball bearings
TAKE-UP - Provides 4 in. of belt take-up at tail pulley
BEARINGS - Sealed, pre-lubricated, self-aligning, ball bearings on drive and tail pulleys
BELT SPEED - Constant 65 FPM
SPEED REDUCTION - Sealed worm gear C-face speed reducer with No. 50 roller chain to drive pulley
MOTOR - 1/2 HP – 230/460 V – 3 phase – 60 Hz totally enclosed fan cooled, energy efficient
FRAME CAPACITY - Maximum load per linear foot of conveyor is 75 lbs. Not to exceed drive capacity in chart.
LOAD CAPACITY (LBS.)
HORIZONTAL W/ STANDARD BELT 25° INCLINE W/ ROUGHTOP
BELTBELT WIDTH
4" DRIVE PULLEY 8" DRIVE PULLEY
FPM HP 11' 31' 51' 77' 101' 11' 31'
35
1/26"-16" 800 790 770 740 720 330 325
18"-30" 790 760 720 680 640 325 315
16"-16" 825*† 1,730* 1,710* 1,690 1,660 725* 715*
18"-30" 825* † 1,690* 1,660* 1,620 1,580 715* 700*
65
1/26"-16" 470 450 430 405 390 195 185
18"-30" 450 420 390 340 300 185 175
16"-16" 825 † 1,030 1,010 980 960 435 425
18"-30" 825 † 1000 960 920 880 425 415
26"-16" 825* † 2,090* 2,070* 2,050 2,030 875* 870*
18"-30" 825* † 2060* 2030* 1,980 1,950 865* 855*
100
1/26"-16" 325 310 290 265 240 135 125
18"-30" 310 275 245 195 160 130 115
16"-16" 720 705 690 660 640 300 290
18"-30" 710 675 640 595 555 295 280
26"-16" 825 † 1,430 1415 1,390 1,365 600 595
18"-30" 825 † 1400 1,370 1,320 1,280 595 580
135
1/26"-16" 250 235 215 190 170 105 95
18"-30" 235 200 170 120 85 95 85
16"-16" 535 520 500 475 455 225 215
18"-30" 520 485 455 405 370 215 205
26"-16" 825 † 1,100 1,085 1,055 1,035 465 455
18"-30" 825 † 1,070 1035 990 950 455 445
* Requires 8" diameter drive pulley in lieu of 4" diameter. †Limited by conveyor capacity
HORIZONTAL BELT CONVEYOR (Slider Bed)
2Roseville, Michigan • Phone: (586) 771-1881 • www.ultimationinc.com
OPTIONAL EQUIPMENTLENGTH / WIDTH - Other in-between widths are lengths are available
FLOOR SUPPORTS - SMS floor supports are available in wide range of adjustments. Specify top of belt elevation. One support is required at every bed joint and at ends of conveyor. Holes in feet are provided for lagging to floor. Knee braces supplied on SMS-7 support and above.
BELT - Tan Glidetop, White Polymate 100 RMP – COS, Black Trackmate 120 Roughtop with PVC cover
BELT SPEED - Other constant and variable speeds • 4 in. dia. drive pulley: 35, 40, 50, 80, 100 and 135 FPM • 8 in. dia. drive pulley: 17 – 135 FPM in any increment • Contact factory for speeds not listed above
OTHER PULLEY OPTIONS • 8 in. dia. drive pulley with 1 7/16 in. dia. shaft at bearings in lieu of 4 in. dia. drive pulley • 6 in. dia. tail pulley with 1 3/16 in. dia. shaft at bearings in lieu of 4 in. dia. tail pulley • 1 1/8 in. dia. nose roller assembly in lieu of 4 in. dia. tail pulley. Center drive is required.
MOTORS - Inverter duty, premium energy efficient, single phase, brake motor, other characteristics. 2 HP maximum.
CENTER DRIVE / TAKE-UP - Provides 16 in. of belt take-up and is suitable for reversing applications • Standard underhung drive (4 in. dia. drive pulley): 16 in. minimum elevation. 78 in. minimum OAL. • Standard underhung drive (8 in. dia. drive pulley): 17 in. minimum elevation. 78 in. minimum OAL. • Side mount drive/low elevation center drive (4 in. or 8 in. dia. drive pulley): 13 1/2
in. minimum elevation. 66 in. minimum OAL.
SHAFT MOUNTED END DRIVE - 4 in. dia. drive pulley only. Drive unit mounted on extended pulley shaft. Mounting bracket and torque arm enable multiple mounting positions. 4 7/8 in. minimum elevation.
OTHER DRIVE VARIATIONS - Side mounted end or center drives
UNDERSIDE TAKE-UP - Provides 16 in. of belt take-up. Extends down 13 1/8 in. from top of belt.
V-GUIDED CONSTRUCTION - When overall length to belt width ratio drops below 2.5:1 but is still greater than 1:1, V-guided belt is required to maintain belt tracking
GRAVITY BRACKETS - Brackets and support bar allows skatewheel or 1 3/8 in. dia. gravity roller conveyor to be supported at end of belt conveyor. Includes 1 in. dia. pop-out transfer roller.
BUTT COUPLINGS - Brackets allow 1.9 in / 2 in. dia. gravity roller conveyor along with other conveyors to be attached to end of belt conveyor. Includes 1 in. dia. pop-out transfer roller. Center drive or underside take-up recommended if butt couplings are to be located at tail end.
GUIDE RAILS - Adjustable channel guide rails, solid side guides
OTHER ACCESSORIES - Floor supports with casters, poly-tier supports, ceiling hangers. See accessory section.
ELECTRICAL CONTROLS - One direction manual start switch, reversing drum switch, non-reversing and reversible IEC starters, push button stations, AC variable frequency drive
2-1/2" DIA.SNUB ROLLER
4"
FORMEDSTEEL BEDBED WIDTH
BELT WIDTH
3-3/4"
2-1/8" DIA.SNUB ROLLER
TOTALLY ENCLOSED CHAIN GUARD
OVERALL LENGTH
BED LENGTH 6"6"
34" MAX.
22-3/4" 11-1/4" MAX.
OPTIONAL SMS SUPPORT SHOWN
15-1/2" MAX.
4-3/4"
2-1/2" DIA.SNUB ROLLER
1.9" DIA. RETURN ROLLER
12" APPROX.
X
X
FLOW4" DIA. DRIVE PULLEY
NIP POINT GUARD
2-1/2" DIA. SNUB ROLLER
4" DIA. TAIL PULLEY
NIP POINT GUARD
TAKE UP
17"
24-3/4" 11-1/4" MAX.
OPTIONAL SMSD SUPPORT SHOWN
19" MAX.
12" APPROX.
9-1/2"
OVERALL LENGTH
BED LENGTH
FLOW
36" MAX.
8" DIA.DRIVE PULLEY
4" END DRIVE
SECTION VIEW X-X 8" END DRIVE 4" SHAFT MOUNTED DRIVE
3
BS300B
Note: A short belt segment laced on both ends, commonly called a “Dutchman”, is provided on conveyors 35 ft. to 70 ft. This allows for future belt stretch with standard end take-up. An underside take-up or center drive with take-up is recommended for conveyors over 70 ft. long.
CONVEYOR WEIGHTS (LBS.)
OVERALL LENGTH 6" DIA. TAIL
PULLEYBED LENGTH
OVERALL LENGTH WITH CENTER
DRIVE
BELT WIDTH
24" 30" 36" 42" 48" 52"
BED WIDTH
30" 36" 42" 48" 54" 58"
7'-1" 5' 6'-4" 461 445 N/A N/A N/A N/A
12'-1" 10' 11'-4" 564 629 698 767 834 880
17'-1" 15' 16'-4" 672 751 837 922 1,003 1,061
22'-1" 20' 21'-4" 775 868 969 1,069 1,166 1,234
27'-1" 25' 26'-4" 883 991 1,108 1,224 1,335 1,415
32'-1" 30' 31'-4" 986 1,108 1,240 1,372 1,498 1,588
37'-1" 35' 36'-4" 1,094 1,230 1,379 1,527 1,667 1,769
42'-1" 40' 41'-4" 1,197 1,347 1,511 1,674 1,830 1,942
47'-1" 45' 46'-4" 1,302 1470 1,650 1,829 1,999 2,123
52'-1" 50' 51'-4" 1,408 1,587 1,782 1,977 2,162 2,296
57'-1" 55' 56'-4" 1,516 1,709 1,921 2,132 2,331 2,477
62'-1" 60' 61'-4" 1,619 1,826 2,053 2,279 2,494 2,650
67'-1" 65' 66'-4" 1,727 1,949 2,192 2,434 2,663 2,831
72'-1" 70' 71'-4" 1,830 2,066 2,324 2,582 2826 3,004
77'-1" 75' 76'-4" 1,938 2,188 2,463 2,737 2,995 3,185
82'-1" 80' 81'-4" 2,041 2,305 2,595 2,884 3,158 3,358
87'-1" 85' 86'-4" 2,149 2,428 2,734 3,089 3,327 3,539
92'-1" 90' 91'-4" 2,252 2,545 2,866 3,187 3,490 3,712
97'-1" 95' 96-4" 2,360 2,667 3,005 3,342 3,659 3,893
102'-1" 100' 101'-4" 2,463 2,784 3,137 3,489 3,822 4,066
STANDARD SPECIFICATIONSBELT - Black Trackmate 120 EMB
BED - 6 5/8 in. deep x 12 ga. powder coated steel slider bed. Standard 5 ft. and 10 ft. long bolt-together sections with splice plates.
END DRIVE - Located on discharge end of conveyor. Chain guard is on left-hand side when standing at infeed looking toward discharge.
DRIVE PULLEY - 8 in. dia. with 1 7/16 in. dia. shaft at bearing. Machined, crowned and fully lagged.
TAIL PULLEY - 6 in. dia. with 1 3/16 in. dia. shaft at bearing. Machined crown
SNUB ROLLERS - Adjustable 2 1/2 in. dia. rollers. Grease packed ball bearings. Includes guard.
RETURN ROLLERS - Adjustable 1.9 in. dia. rollers. Grease packed ball bearings
TAKE-UP - Provides 4 in. of belt take-up at tail pulley
BEARINGS - Sealed, pre-lubricated, self-aligning, ball bearings on drive and tail pulleys
BELT SPEED - Constant 65 FPM
SPEED REDUCTION - Sealed worm gear C-face speed reducer with No. 50 roller chain to drive pulley
MOTOR - 1 HP – 230/460 V – 3 phase – 60 Hz totally enclosed fan cooled, energy efficient
FRAME CAPACITY - Maximum load per linear foot of conveyor is 100 lbs. Not to exceed drive capacity in chart.
LOAD CAPACITY (LBS.)
HORIZONTAL W/ STANDARD BELT
BELT WIDTH
8" DRIVE PULLEY
FPM HP 12' 32' 52' 78' 102'
35 1
24"-30" 1,200* 1,690 1,660 1,620 1,580
36"-42" 1,200* 1,660 1,620 1,560 1,510
48"-52" 1,200* 1,640 1,580 1,510 1,450
65
1
24"-30" 1,020 980 960 910 870
36"-42" 1,000 960 920 860 800
48"-52" 990 930 880 810 740
2
24"-30" 1,200* 2,050 2,020 1,980 1,940
36"-42" 1,200* 2,020 1,980 1,920 1,870
48"-52" 1,200* 1,990 1,940 1,870 1,800
100
1
24"-30" 690 660 630 590 550
36"-42" 670 630 585 530 475
48"-52" 660 605 550 480 410
2
24"-30" 1,200* 1,390 1,355 1,315 1,280
36"-42" 1,200* 1,360 1,310 1,255 1,200
48"-52" 1,200* 1,330 1,275 1,205 1,140
135
1
24"-30" 505 475 445 400 365
36"-42" 485 440 400 340 290
48"-52" 470 415 360 290 225
2
24"-30" 1,090 1,055 1,025 985 945
36"-42" 1,070 1,025 980 925 870
48"-52" 1,055 1,000 945 875 810
HORIZONTAL BELT CONVEYOR (Slider Bed)
With its rugged, heavier duty construction, the BS300B is ideal for transporting larger packages or multiple smaller packages across its width. It can be used in many types of material handling applications such as assembly operations, sorting, packaging, and inspection or for simply transporting product from point A to B.
n Smooth, slim design n Coped ends n 6 belt widths n Multiple belt options
* Limited by conveyor capacity
4Roseville, Michigan • Phone: (586) 771-1881 • www.ultimationinc.com
OPTIONAL EQUIPMENTFLOOR SUPPORTS - SMS floor supports are available in wide range of adjustments. Specify top of belt elevation. One support is required at every bed joint and at ends of conveyor. Holes in feet are provided for lagging to floor. Knee braces supplied on SMS-7 support and above.
BELT - Tan Glidetop, White Polymate 100 RMP - COS, Black Trackmate 120 Roughtop with PVC cover
BELT SPEED - Other constant and variable speeds: 17 - 135 FPM in any increment. Contact factory for speeds not listed.
MOTORS - Inverter duty, premium energy efficient, single phase, brake motor, other characteristics. 2 HP maximum.
CENTER DRIVE / TAKE-UP - Provides 16 in. of belt take-up and is suitable for reversing applications • Standard underhung drive: 20 in. minimum elevation. 78 in. minimum OAL. • Side mount drive/low elevation center drive: 16 1/2 in. minimum elevation. 66 in. minimum OAL.
UNDERSIDE TAKE-UP - Provides 16 in. of belt take-up. Extends down 15 3/4 in. from top of belt.
V-GUIDED CONSTRUCTION - When overall length to belt width ratio drops below 2.5:1 but is still greater than 1:1, V-guided belt is required to maintain belt tracking.
BUTT COUPLINGS - Brackets allow 1.9 in / 2 in. dia. gravity roller conveyor along with other conveyors to be attached to end of belt conveyor. Includes 1 in. dia. pop-out transfer roller. Center drive or underside take-up recommended if butt couplings are to be located at tail end.
GUIDE RAILS - Adjustable channel guide rails, solid side guides
OTHER ACCESSORIES - Floor supports with casters, poly-tier supports, ceiling hangers. See accessory section.
ELECTRICAL CONTROLS - One direction manual start switch, reversing drum switch, non-reversing and reversible IEC starters, push button stations, AC variable frequency drive
OVERALL LENGTH
BED LENGTH 8"17"
36" MAX.
24" 12" MAX.
OPTIONAL SMSD SUPPORT SHOWN
19" MAX.
9-1/2"
2-1/2" DIA.SNUB ROLLER
1.9" DIA. RETURN ROLLER
12" APPROX.
X
X
FLOW8" DIA. DRIVE PULLEY
2-1/2" DIA. SNUB ROLLER
6" DIA. TAIL PULLEY
NIP POINT GUARD
TAKE-UP
8" END DRIVE
SECTION VIEW X-X
6-5/8"
FORMED STEEL BEDBED WIDTH
BELT WIDTH
4"
1.9" DIA. RETURN ROLLER
TOTALLY ENCLOSED CHAIN GUARD
SPREADER
OPTIONAL SMS SUPPORT SHOWN
5
BS100CHORIZONTAL BELT CONVEYOR (Slider Bed)
The BS100C belt conveyor is designed with channel frames and bolt-in pans making it ideal for matching up with other roller bed conveyors. It can be used in many types of material handling applications such as assembly operations, sorting, packaging, and inspection or for simply transporting product from point A to B.
n 15 belt widths n Center drive and take-up n Readily bolts up to other roller bed conveyors n Multiple belt options
STANDARD SPECIFICATIONSBELT – Black Trackmate 120 EMB
BED – 6 1/2 in. deep x 1 1/2 in. flange x 12 ga. powder coated steel channel frame with bolt-in slider pans and cross members. Standard 5 ft. and 10 ft. long bolt-together sections with splice plates.
CENTER DRIVE – Can be placed on any section of conveyor length. Minimum elevation is 17 7/8 in. Minimum OAL is 90". Chain guard is located on left-hand side when standing at infeed looking toward discharge.
DRIVE PULLEY – 8 in dia. with 1 7/16 in. dia. shaft at bearing. Machined, crowned and fully lagged.
TAIL PULLEY – 4 in. dia. with 1 in. dia. shaft at bearing or 6 in. dia. with 1 3/16 in. dia. shaft at bearing. Machined crown.
SNUB ROLLERS – Adjustable 2 1/2 in. dia. rollers. Grease packed ball bearings. Includes guard.
RETURN ROLLERS – Adjustable 1.9 in. dia. rollers. Grease packed ball bearings
TAKE-UP – Located in center drive. Provides 16 in. of belt take-up.
BEARINGS – Sealed, pre-lubricated, self-aligning, ball bearings on drive and tail pulleys
BELT SPEED – Constant 65 FPM
SPEED REDUCTION - Sealed worm gear C-face speed reducer with No. 50 roller chain to drive pulley
MOTOR – 1 HP –230/460V – 3 phase – 60 Hz totally enclosed fan cooled, energy effcient
FRAME CAPACITY – Maximum load per linear foot of conveyor is 100 lbs. Not to exceed drive capacity in chart.
CONVEYOR WEIGHTS (LBS.)
OVERALL LENGTH
BED LENGTH
BELT WIDTH
10" 12" 14" 16" 18" 20" 22" 24" 28" 30" 34" 36" 42" 48" 54"
BETWEEN FRAME WIDTH
13" 15" 17" 19" 21" 23" 25" 27" 31" 33" 37" 39" 45" 51" 57"
OVERALL FRAME WIDTH
16" 18" 20" 22" 24" 26" 28" 30" 34" 36" 40" 42" 48" 54" 60"
4 IN. DIA. TAIL PULLEYS 6 IN. DIA. TAIL PULLEYS
12' 10' 513 555 595 636 677 717 758 860 933 984 1,050 1,098 1,231 1,360 1,498
17' 15' 595 643 690 736 783 829 877 986 1,070 1,127 1,198 1,253 1,409 1,556 1,71122' 20' 674 727 780 832 884 937 991 1,106 1,202 1,265 1,342 1,403 1,582 1,747 1,91927' 25' 753 812 870 928 986 1,044 1,103 1,225 1,331 1,400 1,483 1,549 1,750 1,931 2,12032' 30' 831 896 960 1,023 1,087 1,151 1,217 1,345 1,463 1,538 1,627 1,699 1,923 2,122 2,32837' 35' 911 982 1,050 1,119 1,189 1,258 1,330 1,463 1,592 1,673 1,767 1,844 2,091 2,306 2,52942' 40' 989 1,065 1,140 1,215 1,290 1,366 1,444 1,584 1,724 1,811 1,911 1,994 2,264 2,497 2,73747' 45' 1,068 1,151 1,230 1,311 1,392 1,473 1,556 1,702 1,854 1,945 2,051 2,140 2,431 2,681 2,93852' 50' 1,146 1,235 1,320 1,406 1,494 1,580 1,670 1,822 1,985 2,083 2,195 2,290 2,605 2,872 3,14657' 55' 1,226 1,320 1,411 1,503 1,595 1,687 1,783 1,940 2,115 2,218 2,335 2,436 2,773 3,056 3,34762' 60' 1,304 1,403 1,500 1,598 1,697 1,795 1,897 2,061 2,247 2,356 2,480 2,586 2,945 3,247 3,55567' 65' 1,383 1,489 1,592 1,694 1,798 1,902 2,010 2,179 2,376 2,491 2,620 2,732 3,113 3,431 3,75672' 70' 1,461 1,573 1,681 1,790 1,900 2009 2,124 2,300 2,508 2,629 2,764 2,882 3,286 3,622 3,96477' 75' 1,541 1,658 1,772 1,886 2,001 2,116 2,237 2,418 2,637 2,764 2,904 3,028 3,454 3,806 4,16582' 80' 1,619 1,742 1,862 1,981 2,103 2,224 2,351 2,539 2,769 2,902 3,048 3,178 3,627 3,997 4,37387' 85' 1,698 1,827 1,952 2,077 2,205 2,331 2,463 2,657 2,898 3,037 3,188 3,323 3,795 4,181 4,57492' 90' 1,776 1,911 2,042 2,173 2,306 2,438 2,577 2,777 3,030 3,175 3,332 3,473 3,968 4,372 4,78297' 95' 1,855 1,996 2,133 2,269 2,408 2,545 2,690 2,895 3,160 3,309 3,473 3,619 4,136 4,556 4,983
102' 100' 1,934 2,080 2,222 2,365 2,509 2,653 2,804 3,016 3,292 3,447 3,617 3,769 4,309 4,747 5,191
LOAD CAPACITY (LBS.)
HORIZONTAL W/ STANDARD BELT
BELT
WIDTH
8" DRIVE PULLEY
FPM HP 12' 32' 52' 77' 102'
35 1
10"-18" 1,200* 1,720 1,710 1,680 1,660
20"-30" 1,200* 1,700 1,680 1,640 1,600
34"-54" 1,200* 1,660 1,610 1,540 1,480
65
1
10"-18" 1,045 1,030 1,010 990 970
20"-30" 1,030 1,000 970 940 900
34"-54" 1,000 950 900 840 780
2
10"-18" 1,200* 2,095 2,080 2,050 2,030
20"-30" 1,200* 2,070 2,040 2,000 1,970
34"-54" 1,200* 2,020 1,970 1,900 1,840
100
1
10"-18" 720 700 685 660 640
20"-30" 705 680 650 610 580
34"-54" 680 630 580 510 450
2
10"-18" 1,200* 1,430 1,410 1,390 1,370
20"-30" 1,200* 1,405 1,380 1,340 1,310
34"-54" 1,200* 1,355 1,305 1,240 1,180
135
1
10"-18" 530 515 500 475 455
20"-30" 520 490 465 425 395
34"-54" 490 440 390 325 265
2
10"-18" 1,115 1,100 1,080 1,060 1,040
20"-30" 1,100 1,075 1,045 1,010 975
34"-54" 1,075 1,025 975 910 850
* Limited by conveyor capacity
6Roseville, Michigan • Phone: (586) 771-1881 • www.ultimationinc.com
OPTIONAL EQUIPMENTFLOOR SUPPORTS – SMS floor supports are available in wide range of adjustments. Specify top of belt elevation. One support is required at every bed joint and at ends of conveyor. Holes in feet are provided for lagging to floor. Knee braces supplied on SMS-7 support and above.
BELT – Tan Glidetop, White Polymate 100 RMP – COS, Black Trackmate 120 Roughtop with PVC cover
BELT SPEED – Other constant and variable speeds: 17 – 135 FPM in any increment. Contact factory for other speeds.
MOTORS – Inverter duty, premium energy efficient, single phase, brake motor, other characteristics. 2 HP maximum.
SIDE MOUNT CENTER DRIVE / TAKE-UP – Provides 16 in. of belt take-up. 16 1/2 in. minimum elevation. 78 in. minimum OAL.
END DRIVE – Requires underside take-up
• 8 in. underhung end drive: 16 in. minimum elevation. 104 in. minimum OAL. • 8 in. side mount end drive: 13 in. minimum elevation. 96 in. minimum OAL.
UNDERSIDE TAKE-UP – Provides 16 in. of belt take-up. Extends down 15 7/8 in. from top of belt.
8" CENTER DRIVE
SECTION VIEW X-X
PULLEYS – 6 in. dia. tail with 1 3/16 in. dia. shaft at bearing in place of 4 in. when not furnished as standard
V-GUIDED CONSTRUCTION – When overall length to belt width ratio drops below 2.5:1 but is still greater than 1:1, V-guided belt is required to maintain belt tracking.
SLAVE KIT – To slave VBC19 curve from system end of belt conveyor
GUIDE RAILS – Adjustable channel guide rails, fixed angle and channel guide rails
OTHER ACCESSORIES – Floor supports with casters, poly-tier supports, ceiling hangers. See accessory section.
ELECTRICAL CONTROLS – One direction manual start switch, reversing drum switch, non-reversing and reversible IEC starters, push button stations, AC variable frequency drive.
7
LOAD CAPACITY (LBS)
HORIZONTAL W/ STANDARD BELT
BELT
WIDTH
8" DRIVE PULLEY
FPM HP 12' 32' 52' 77' 102'
35
1/210"-18" 2,700* 4,600 4,400 4,200 4,00020"-30" 2,700* 4,400 4,100 3,800 3,50034"-54" 2,700* 4,000 3,600 3,000 2,400
110"-18" 2,700* 7,200* 10,100 9,900 9,60020"-30" 2,700* 7,200* 9,800 9,500 9,10034"-54" 2,700* 7,200* 9,200 8,700 8,100
65
1/210"-18" 2,700* 2,600 2,400 2,200 2,00020"-30" 2,650 2,400 2,100 1,800 1,45034"-54" 2,500 2,000 1,600 1,000 450
110"-18" 2,700* 6,050 5,900 5,650 5,45020"-30" 2,700* 5,900 5,600 5,250 4,95034"-54" 2,700* 5,500 5,050 4,450 3,900
210"-18" 2,700* 7,200* 12,,300 12,050 11,85020"-30" 2,700* 7,200* 12000 11,650 11,35034"-54" 2,700* 7,200* 11,450 10,850 10,300
100
1/210"-18" 1,900 1,750 1,550 1,350 1,15020"-30" 1,800 1,550 1,300 950 60034"-54" 1,650 1,200 750 150 NA
110"-18" 2,700* 4,100 3,950 3,700 3,50020"-30" 2,700* 3,950 3,650 3,300 3,00034"-54" 2,700* 3,550 3,100 2,500 1,950
210"-18" 2,700* 7,200* 8,300 8,050 7,85020"-30" 2,700* 7,200* 8,050 7,650 7,35034"-54" 2,700* 7,200* 7,450 6,850 6,350
135
1/210"-18" 1,450 1,300 1,100 900 65020"-30" 1,350 1,100 850 500 15034"-54" 1,200 750 300 NA NA
110"-18" 2,700* 3,000 2,850 2,600 2,40020"-30" 2,700* 2,800 2,550 2,200 1,90034"-54" 2,700* 2,450 2,000 1,400 850
210"-18" 2,700* 6,500 6,300 6,100 5,90020"-30" 2,700* 6,300 6,000 5,700 5,35034"-54" 2,700* 5,950 5,500 4,900 4,350
BR100CHORIZONTAL BELT CONVEYOR (Roller Bed)
The BR100C belt conveyor is ideal for moving heavier loads. The roller bed design reduces belt friction which increase it’s load capacity. It can be used in many types of material handling applications such as assembly operations, packaging, and inspection or for simply transporting product from point A to B.
n 15 belt widths n Center drive and take-up nIdeal for heavier loads n Readily bolts up to other roller bed conveyors
STANDARD SPECIFICATIONSBELT – Black Trackmate 120 EMB
BED – 6-1/2 in. deep x 1 1/2 in. flange x 12 ga. powder coated steel channel frame with 1.9 dia. roller x 16 ga. tube spaced every 6 in. Standard 5 ft. and 10 ft. bolt-together sections with splice plates.
CROSS BRACING – Rods with turnbuckles are fastened to underside of bed to provide squaring adjustment and insure correct product tracking. Supplied on every other section, 30 ft. bed lengths and over.
CENTER DRIVE – Can be placed on any section of conveyor length. Minimum elevation – 17 7/8 in. Minimum OAL is 90". Chain guard is on left-hand side when standing at infeed looking toward discharge.
DRIVE PULLEY – 8 in dia. with 1 7/16 in. dia. shaft at bearing. Machined, crowned and fully lagged.
TAIL PULLEY – 4 in. dia. with 1 in. dia. shaft at bearing or 6 in. dia. with 1 3/16 in. dia. shaft at bearing. Machined crown
SNUB ROLLERS – Adjustable 2 1/2 in. dia. rollers. Grease packed ball bearings. Includes guard.
RETURN ROLLERS – Adjustable 1.9 in. dia. rollers. Grease packed ball bearings
TAKE-UP – Provides 16 in. of belt take-up in center drive
BEARINGS – Sealed, pre-lubricated, self-aligning, ball bearings on drive and tail pulleys.
BELT SPEED – Constant 65 FPM
SPEED REDUCTION - Sealed worm gear C-face speed reducer with No. 50 roller chain to drive pulley
MOTOR – 1/2 HP – 230/460 V – 3 phase – 60 Hz totally enclosed fan cooled, energy efficient
FRAME CAPACITY – Maximum load per linear foot of conveyor is 225 lbs. Not to exceed drive capacity in chart.
CONVEYOR WEIGHTS (LBS.)
OVERALL LENGTH
BED LENGTH
BELT WIDTH
10" 12" 14" 16" 18" 20" 22" 24" 28" 30" 34" 36" 42" 48" 54"
BETWEEN FRAME WIDTH
13" 15" 17" 19" 21" 23" 25" 27" 31" 33" 37" 39" 45" 51" 57"
OVERALL FRAME WIDTH
16" 18" 20" 22" 24" 26" 28" 30" 34" 36" 40" 42" 48" 54" 60"
4 IN. DIA. TAIL PULLEYS 6 IN. DIA. TAIL PULLEYS
12' 10' 518 562 600 638 682 725 778 832 891 935 1005 1048 1,160 1,274 1390
17' 15' 602 654 697 740 791 841 907 973 1,042 1,094 1,172 1,223 1,351 1,481 1,61522' 20' 683 742 789 837 895 953 1,032 1,110 1,188 1,247 1,335 1,393 1,538 1,684 1,83427' 25' 765 831 882 934 999 1,064 1,154 1,245 1,331 1,397 1,494 1559 1,719 1,881 2,04632' 30' 845 918 975 1,031 1,103 1,175 1,279 1,382 1,477 1,551 1,657 1,729 1,905 2,084 2,26637' 35' 927 1,007 1,068 1,128 1,207 1,286 1,402 1,517 1,621 1,701 1,815 1,894 2,086 2,280 2,47842' 40' 1,007 1,095 1,160 1,225 1,311 1,398 1,526 1,654 1,767 1,855 1,978 2,064 2,273 2,484 2,69747' 45' 1,089 1,183 1,253 1,323 1,416 1,509 1,649 1,789 1,910 2,005 2,137 2,230 2,454 2,681 2,91052' 50' 1,169 1,271 1,345 1,419 1,520 1,620 1,773 1,926 2,057 2,158 2,300 2,400 2,641 2,884 3,12957' 55' 1,251 1,360 1,438 1,517 1,624 1,731 1,896 2,061 2,200 2,309 2,459 2,566 2,822 3,080 3,34162' 60' 1,332 1,447 1,530 1,614 1,728 1,842 2,020 2,197 2,346 2,462 2,621 2,736 3,009 3,283 3,56167' 65' 1,413 1,536 1,624 1,711 1,832 1,954 2,143 2,332 2,490 2,612 2,780 2,902 3,190 3,480 3,77372' 70' 1,494 1,624 1,716 1,808 1,936 2,065 2,267 2,469 2,636 2,766 2,943 3,072 3,376 3,683 3,99377' 75' 1,576 1,712 1,809 1,905 2,041 2,176 2,390 2,604 2,779 2,916 3,102 3,238 3,558 3,880 4,20582' 80' 1,656 1,800 1,901 2,002 2,144 2,288 2,514 2,741 2,925 3,070 3,265 3,408 3,744 4,082 4,42487' 85' 1,738 1,889 1,994 2,099 2,248 2,399 2,637 2,876 3,059 3,220 3,424 3,573 3,925 4,279 4,63692' 90' 1,818 1,976 2,086 2,196 2,353 2,510 2,762 3,013 3,215 3,373 3,586 3,743 4,112 4,483 4,85697' 95' 1,900 2,065 2,179 2,294 2,457 2,621 2,885 3,148 3,359 3,524 3,745 3,909 4,293 4,979 5,068
102' 100' 1,980 2,153 2,272 2,390 2,561 2,732 3,008 3,285 3,505 3,677 3,908 4,079 4,480 4,882 5,288
* Limited by conveyor capacity
8Roseville, Michigan • Phone: (586) 771-1881 • www.ultimationinc.com
OPTIONAL EQUIPMENTFLOOR SUPPORTS – SMS floor supports are available in wide range of adjustments. Specify top of belt elevation. One support is required at every bed joint and at ends of conveyor. Holes in feet are provided for lagging to floor. Knee braces supplied on SMS-7 support and above.
BELT – Tan Glidetop, White Polymate 100 RMP – COS, Black Trackmate 533 COS-PVC
BELT SPEED – Other constant and variable speeds: 17 – 135 FPM in any increment. Contact factory for speeds not listed above.
MOTORS – Inverter duty, premium energy efficient, single phase, brake motor, other characteristics. 2 HP maximum.
SIDE MOUNT CENTER DRIVE / TAKE-UP – Provides 16 in. of belt take-up. 16 1/2 in. minimum elevation. 60 in. minimum OAL
END DRIVE – Requires underside take-up
• 8 in. underhung end drive: 16 in. minimum elevation. 104 in. minimum OAL. • 8 in. side mount end drive: 13 in. minimum elevation. 96 in. minimum OAL.
UNDERSIDE TAKE-UP – Provides 16 in. of belt take-up. Extends down 15 7/8 in. from top of belt.
8" CENTER DRIVE
SECTION VIEW X - X
ROLLER CENTERS – Bed rollers spaced on 3 in., 9 in., or 12 in. centers.
PULLEYS – 6 in. dia. tail with 1-3/16 in. dia. shaft at bearing in place of 4 in. when not furnished as standard.
SLAVE KIT – To slave VBC19 curve from system end of belt conveyor.
GUIDE RAILS – Adjustable channel guide rails, fixed angle and channel guide rails.
OTHER ACCESSORIES – Floor supports with casters, poly-tier supports, ceiling hangers. See accessory section.
ELECTRICAL CONTROLS – One direction manual start switch, reversing drum switch, non-reversing and reversible IEC starters, push button stations, AC variable frequency drive.
OVERALL LENGTH
63" MAX.
12" APPROX.
10 7/8"
8" 8" 17-7/8"
26-1/2" 21"
12" 12" BED LENGTH
PREFERREDFLOW
X
X
2-1/2" DIA. SNUB ROLLER
TAKE-UP 6" DIA. TAKE-UP PULLEY
1.9" DIA. TREAD ROLLER
8" DIA. DRIVE PULLEY
1.9" DIA. RETURN IDLER
4" OR 6" DIA. TAIL PULLEY
1.9" DIA. POP-OUT ROLLER
OPTIONAL SMS SUPPORT SHOWN2-1/2" DIA. SNUB IDLER
9
BSCThe BSC belt curve is ideal for transporting products of various sizes and shapes. It helps maintain proper product orientation and positive traction through the curve.
n 8 conveying widths n Quiet and low maintenance belt guiding system n 45, 90, and 180 degree curves
BELT CURVE
OR OUTSIDE RADIUS
CONVEYING WIDTH
IR INSIDE RADIUS
CR CENTER
LINE RADIUS
F BOTTOM
OF FRAME TO TOB
H FRAME HEIGHT
J GAP (APPROX.)PULLEY SHAFT SIZE
MAX. DISTRIB.
LIVE LOAD (LBS)
WEIGHT (LBS.)
MIN. MAX. NORM. 45° 90° 180
48"
12" 36" 42"
9 1/16" 10 15/16"
3 5/8" 5 1/8" 4"
1" 400
169 337 674
18" 30" 39" 3 1/4" 4 3/4" 3 5/8" 187 374 748
20" 28" 38" 3 1/4" 4 5/8" 3 5/8" 191 381 762
24" 24" 36" 3" 4 3/8" 3 3/8" 200 399 798
60"
24" 36" 48"
10 9/16" 12 3/8"
4 1/8" 5 7/8" 4 9/16"
1 3/16" 600
261 521 1,042
30" 30" 45" 3 7/8" 5 7/8" 4 3/8" 278 556 1,112
36" 24" 42" 3 5/8" 5 1/8" 4" 294 587 1,174
72"
36" 36" 54"
12" 13 7/8"
4 1/4" 6 5/8" 4 7/8"
1 7/16" 700
379 757 1,514
42" 30" 51" 4" 6 1/4" 4 5/8" 398 795 1,590
48" 24" 48" 3 3/4" 5 7/8" 4 1/4" 414 828 1,656
STANDARD SPECIFICATIONSBELT - Black Trackmate 120 EMB
BED - 10 ga. steel frame and slider bed pan. Welded construction.
CURVES - 45, 90 and 180 degree curves. Radius is dependent upon conveying width (see chart).
DRIVE AND TAIL PULLEYS - Tapered pulley with ruff-top lagging
BEARINGS - Sealed, pre-lubricated, self-aligning ball bearings on drive and tail pulleys.
BELT GUIDING SYSTEM - Belt is mechanically guided at outside rail with wheel. These wheels provide quiet operation, minimal friction and require virtually no maintenance.
BELT SPEED - Constant 65 FPM at belt centerline
SPEED REDUCTION - Sealed worm gear shaft mounted speed reducer
MOTOR – 3/4 HP - 230/460 V - 3 phase - 60 Hz. - totally enclosed fan cooled, energy efficient
CAPACITY – See chart
LOAD CAPACITY
FPM HPOR
OUTSIDE RADIUS
CONVEYING WIDTH
DEGREE
45° 90° 180°
65
3/448" 12"-24" 380 360 31060" 24"-36" 310 280 19072" 36"-48" 200 190 150
148" 12"-24" 400* 400* 400*60" 24"-36" 540 510 43072" 36"-48" 430 390 270
248" 12"-24" 400* 400* 400*60" 24"-36" 600* 600* 600*72" 36"-48" 700* 700* 700*
FLOOR SUPPORTS – H-style floor supports are available with +/- 2 in. adjustment. Specify top of belt elevation. One support is required at each end along with one single support at the center. Holes in feet are provided for lagging to floor.
BELT – PVC-120 white, Trackmate 120 RT-B Roughtop, food grade and other belts available
BELT SPEED – Other constant and variable speeds up to 300 FPM. Note: Capacity is affected with speed range.
OTHER ACCESSORIES – Guide rails, ceiling hangers
ELECTRICAL CONTROLS – Non-reversing and reversible IEC starters and push button stations, AC variable frequency drive
OPTIONAL EQUIPMENT
* Maximum distributed live load for curve Contact factory for drive capacity at other speeds
10
BSIThe BSI belt conveyor is ideal for transporting product from floor-to-floor or as a booster conveyor in gravity flow systems. It includes an adjustable double nose-over to ensure smooth transfer from incline to horizontal that can be easily adjusted up to 30 degrees. The frame design makes it ideal for matching up with other roller bed conveyors.
* See incline dimensional chart for full list of vertical and horizontal dimensions at different bed lengths and degrees of incline
n 12 belt widths n Double nose-over n Readily bolts up to other roller bed conveyors in a system
STANDARD SPECIFICATIONSBELT – Black Trackmate 120 Roughtop with PVC coverBED – 6 1/2 in. deep x 12 ga. powder coated steel channel frame. Standard 4 ft., 6 ft., 8ft. and 10 ft. long bolt-together sections with splice plates. Bolt-in 12 ga. galvanized slider pans.DOUBLE NOSE-OVER – A 26 in. long horizontal and 12 in. long nose-over section provides a 2 stage transition from incline to horizontal. Provides 30 degrees of adjustment.POWERED INFEED – Short section of slider bed belt conveyor chain driven from tail pulley of incline CENTER DRIVE – Located on incline bed section. Chain guard is on left hand side when standing at infeed looking toward discharge. • DRIVE PULLEY – 8 in. dia. with 1 7/16 in. dia. shaft at bearings. Machined crowned and fully lagged. • TAKE-UP PULLEY – 6 in. dia. with 1 3/16 in. dia. shaft at bearings. Machined crown. • TAKE-UP – Provides 16 in. of belt take-up in center drive.TAIL PULLEY – 4 in. dia. with 1 in. dia. shaft at bearing or 6 in. dia. with 1 3/16 in. dia. shaft at bearing. Machined crown.SNUB / NOSE-OVER ROLLERS – Adjustable 2 1/2 in. dia. rollers. Grease packed ball bearings. Includes guard. RETURN ROLLERS – Adjustable 1.9 in. dia. rollers. Grease packed ball bearings.BEARINGS – Sealed, pre-lubricated, self-aligning, ball bearings on drive and tail pulleysBELT SPEED – Constant 65 FPM
LOAD CAPACITY (LBS.)
BELTWIDTH
25° INCLINE W/ ROUGHTOP BELT
FPM HP 24' 44'
35 1
10"-16" 819 813
18"-24" 813 805
28"-36" 805 791
65
1
10"-16" 434 426
18"-24" 429 420
28"-36" 420 406
2
10"-16" 883 875
18"-24" 877 868
28"-36" 868 855
100
1
10"-16" 277 269
18"-24" 272 263
28"-36" 263 250
2
10"-16" 569 561
18"-24" 563 554
28"-36" 555 541
135
1
10"-16" 202 194
18"-24" 196 187
28"-36" 188 174
2
10"-16" 418 410
18"-24" 412 403
28"-36" 404 390
INCLINE BELT CONVEYOR (Slider Bed)
CONVEYOR WEIGHTS (LBS.)
BED LENGTH
DIMENSIONS @ 25° WITH 4" DIA. TAIL PULLEY *
OVERALL LENGTH
(REF.)
BELT WIDTH
OVERALL LENGTH
(REF.)
BELT WIDTH
10" 12" 14" 16" 18" 20" 22" 24" 28" 30" 34" 36"
VERTICAL LIFT "VL"
HORIZONTAL DISTANCE
ALONG FLOOR "HF"
BETWEEN FRAME WIDTH BETWEEN FRAME WIDTH
13" 15" 17" 19" 21" 23" 25" 27" 31" 33" 37" 39"
OVERALL FRAME WIDTH OVERALL FRAME WIDTH
16" 18" 20" 22" 24" 26" 28" 30" 34" 36" 40" 42"
4 IN. DIA. TAIL PULLEYS 6 IN. DIA. TAIL PULLEYS
10' 4' - 7" 12' - 10" 13'-10" 665 719 787 840 894 946 999 14' 1,311 1,456 1,534 1,676 1,752
12' 5' - 5" 14' - 7" 15'-10" 692 749 820 876 932 988 1,043 16' 1,358 1,508 1,588 1,733 1,812
14' 6' - 3" 16' - 5" 17'-10" 720 779 853 911 971 1,029 1,088 18' 1,405 1,559 1,642 1,789 1,871
16' 7' - 1" 18' - 3" 19'-10" 755 816 891 951 1,011 1,071 1,132 20' 1,451 1,609 1,694 1,843 1,926
18' 8' - 0" 20' - 1" 21'-10" 783 846 924 986 1,050 1,112 1,176 22' 1,498 1,661 1,748 1,899 1,985
20' 8' - 10" 21' - 10" 23'-10" 813 878 957 1,021 1,086 1,150 1,215 24' 1,540 1,706 1,795 1,948 2,035
22' 9' - 8" 23' - 8" 25'-10" 841 909 990 1,057 1,125 1,191 1,259 26' 1,586 1,758 1,849 2,005 2,095
24' 10' - 6" 25' - 6" 27'-10" 868 939 1,023 1,093 1,163 1,232 1,304 28' 1,633 1,809 1,903 2,061 2,154
26' 11' - 4" 27' - 4" 29'-10" 900 972 1,058 1,128 1,199 1,270 1,342 30' 1,672 1,852 1,947 2,106 2,200
28' 12' - 2" 29' - 1" 31'-10" 928 1,003 1,091 1,164 1,238 1,311 1,386 32' 1,719 1,903 2,001 2,163 2,259
30' 13' - 0" 30' - 11" 33'-10" 958 1,035 1,124 1,198 1,274 1,348 1,425 34' 1,761 1,949 2,048 2,211 2,309
32' 13' - 11" 32' - 9" 35'-10" 986 1,065 1,157 1,234 1,313 1,390 1,469 36' 1,808 2,000 2,102 2,268 2,369
34' 14' - 9" 34' - 7" 37'-10" 1,014 1,095 1,190 1,270 1,351 1,431 1,514 38' 1,855 2,051 2,156 2,324 2,428
36' 15' - 7" 36' - 4" 39'-10" 1,046 1,128 1,224 1,305 1,387 1,468 1,552 40' 1,894 2,094 2,200 2,369 2,474
38' 16' - 5" 38' - 2" 41'-10" 1,073 1,159 1,257 1,341 1,426 1,510 1,596 42' 1,941 2,145 2,254 2,426 2,533
40' 17' - 3" 40' - 0" 43'-10" 1,104 1,191 1,290 1,375 1,462 1,547 1,635 44' 1,982 2,191 2,301 2,475 2,583
SPEED REDUCTION – Sealed worm gear C-face speed reducer with No. 50 roller chain to drive pulleyMOTOR – 1 HP – 230/460 V – 3 phase – 60 Hz totally enclosed fan cooled brake motor, energy efficientFRAME CAPACITY – Maximum load per linear foot of conveyor is 100 lbs. Not to exceed drive capacity in chart.
11Roseville, Michigan • Phone: (586) 771-1881 • www.ultimationinc.com
OPTIONAL EQUIPMENTFLOOR SUPPORTS – SMS floor supports are available in wide range of adjustments. Specify top of belt elevation. One support is required at every bed joint and at ends of conveyor. Holes in feet are provided for lagging to floor. Knee braces supplied on SMS-3 support and above.
BELT – Brown polymate roughtop w/ nitrile cover, pure gum rubber roughtop
BELT SPEED – Other constant and variable speeds: 17-135 FPM in any increment. Contact factory for speeds not listed above.
MOTORS – Premium energy efficient, single phase, other characteristics. 2 HP maximum.
OTHER DRIVE VARIATIONS • Side mount center drive • End drive with underhung or side mount drive. Requires underside take-up.
PULLEYS – 6 in. dia. tail with 1-3/16 in. dia. shaft at bearing in place of 4 in. when not furnished as standard.
UNDERTRUSSING – Available under incline bed sections in place of floor supports or ceiling hangers. Maximum bed length is 40 ft. Maximum belt width is 24 in. See bed and undertrussing information.
GUIDE RAILS – Adjustable channel guard rails, fixed angle and channel guide rails.
OTHER ACCESSORIES – Ceiling hangers. See accessory section.
ELECTRICAL CONTROLS – One direction manual start switch, reversing drum switch, non-reversing and reversible IEC starters, push button stations, AC variable frequency drive.
BETWEEN FRAME WIDTH
OVERRALL FRAME WIDTH
1-1/2"
6-1/2"
3-3/8"
BELT WIDTH 3/8"
BOLT-INSLIDER PAN
2-1/2" DIA. SNUB IDLER/1.9" RETURN IDLER
TOTALLY ENCLOSEDCHAIN GUARD
CROSS MEMBERS
SECTION "X-X"SECTION VIEW "X-X"
8" CENTER DRIVE
12
BRIThe BRI belt conveyor is ideal for transporting heavier products from floor-to-floor or as a booster conveyor in gravity flow systems. The roller bed design reduces belt friction and provides greater capacity. It includes an adjustable double nose-over to ensure smooth transfer from incline to horizontal that can be easily adjusted up to 30 degrees. The frame design makes it ideal for matching up with other roller bed conveyors.
* See incline dimensional chart for full list of vertical and horizontal dimensions at different bed lengths and degrees of incline
n 12 belt widths n Double nose-over n Readily bolts up to other roller bed conveyors in a system
STANDARD SPECIFICATIONSBELT – Black Trackmate 120 Roughtop with PVC coverBED – 6 1/2 in. deep x 12 ga. powder coated steel channel frame with 1.9 dia. roller x 16 ga. tube spaced every 6 in. Standard 4 ft., 6 ft., 8ft. and 10 ft. long bolt-together sections with splice plates.DOUBLE NOSE-OVER – A 26 in. long horizontal and 12 in. long nose-over section provides a 2 stage transition from incline to horizontal. Provides 30 degrees of adjustment.POWERED INFEED – Short section of roller bed belt conveyor chain driven from tail pulley of incline. CENTER DRIVE – Located on incline bed section. Chain guard is on left hand side when standing at infeed looking toward discharge. • DRIVE PULLEY – 8 in. dia. with 1 7/16 in. dia. shaft at bearings. Machined crowned and fully lagged. • TAKE-UP PULLEY – 6 in. dia. with 1 3/16 in. dia. shaft at bearings. Machined crown. • TAKE-UP – Provides 16 in. of belt take-up in center driveTAIL PULLEY – 4 in. dia. with 1 in. dia. shaft at bearing or 6 in. dia. with 1-3/16 in. dia. shaft at bearing. Machined crown.SNUB / NOSE-OVER ROLLERS – Adjustable 2 1/2 in. dia. rollers. Grease packed ball bearings. Includes guard. RETURN ROLLERS – Adjustable 1.9 in. dia. rollers. Grease packed ball bearings.BEARINGS – Sealed, pre-lubricated, self-aligning, ball bearings on drive and tail pulleysBELT SPEED – Constant 65 FPM
LOAD CAPACITY (LBS.)
BELTWIDTH
25° INCLINE W/ ROUGHTOP BELT
FPM HP 24' 44'
35 110"-16" 1,240 1,22418"-24" 1,232 1,20728"-36" 1,216 1,181
65
110"-16" 652 63618"-24" 645 61928"-36" 629 593
210"-16" 1,341 1,32218"-24" 1,330 1,30528"-36" 1314 1,279
100
110"-16" 415 39618"-24" 405 37928"-36" 389 353
210"-16" 861 84218"-24" 850 82528"-36" 834 799
135
110"-16" 300 28118"-24" 289 26128"-36" 273 238
210"-16" 630 61118"-24" 619 59428"-36" 603 568
INCLINE BELT CONVEYOR (Roller Bed)
CONVEYOR WEIGHTS (LBS.)
BED LENGTH
DIMENSIONS @ 25° WITH 4" DIA. TAIL PULLEY *
OVERALL LENGTH
(REF.)
BELT WIDTH
OVERALL LENGTH
(REF.)
BELT WIDTH
10" 12" 14" 16" 18" 20" 22" 24" 28" 30" 34" 36"
VERTICAL LIFT "VL"
HORIZONTAL DISTANCE
ALONG FLOOR "HF"
BETWEEN FRAME WIDTH BETWEEN FRAME WIDTH
13" 15" 17" 19" 21" 23" 25" 27" 31" 33" 37" 39"
OVERALL FRAME WIDTH OVERALL FRAME WIDTH
16" 18" 20" 22" 24" 26" 28" 30" 34" 36" 40" 42"
4 IN. DIA. TAIL PULLEYS 6 IN. DIA. TAIL PULLEYS
10' 4' - 7" 12' - 10" 13'-10" 669 726 792 842 899 954 1,020 14' 1,344 1,485 1,565 1,714 1,792
12' 5' - 5" 14' - 7" 15'-10" 699 759 827 880 939 998 1,069 16' 1,399 1,543 1,626 1,779 1,861
14' 6' - 3" 16' - 5" 17'-10" 730 792 862 917 980 1,042 1,118 18' 1,453 1,601 1,687 1,844 1,929
16' 7' - 1" 18' - 3" 19'-10" 763 828 899 955 1,020 1,084 1,165 20' 1,505 1,655 1,744 1,903 1,990
18' 8' - 0" 20' - 1" 21'-10" 792 861 934 992 1,061 1,128 1,214 22' 1,559 1,713 1,805 1,968 2,058
20' 8' - 10" 21' - 10" 23'-10" 822 893 967 1026 1,096 1,166 1,256 24' 1,606 1,763 1,857 2,023 2,115
22' 9' - 8" 23' - 8" 25'-10" 852 926 1,002 1,063 1,137 1,210 1,305 26' 1,660 1,821 1918 2,088 2,184
24' 10' - 6" 25' - 6" 27'-10" 881 959 1,037 1101 1,178 1,254 1,355 28' 1,715 1,879 1,980 2,153 2,252
26' 11' - 4" 27' - 4" 29'-10" 913 992 1,071 1,135 1,213 1,291 1,395 30' 1,759 1,926 2,028 2,204 2,304
28' 12' - 2" 29' - 1" 31'-10" 942 1,024 1,106 1,172 1,254 1,335 1,445 32' 1,813 1984 2,089 2,269 2,372
30' 13' - 0" 30' - 11" 33'-10" 972 1,056 1,139 1206 1,290 1,372 1,487 34' 1,860 2,034 2,141 2,323 2,429
32' 13' - 11" 32' - 9" 35'-10" 1,002 1,089 1,174 1,243 1,330 1,416 1,536 36' 1,915 2,092 2,203 2,388 2,498
34' 14' - 9" 34' - 7" 37'-10" 1,031 1,122 1,209 1,280 1,371 1460 1,585 38' 1,969 2,150 2,264 2,453 2,566
36' 15' - 7" 36' - 4" 39'-10" 1,063 1,155 1,242 1,315 1,407 1,498 1,626 40' 2,013 2,197 2,312 2,504 2,618
38' 16' - 5" 38' - 2" 41'-10" 1,092 1,188 1,277 1,352 1,447 1,541 1,675 42' 2,068 2,255 2,374 2,569 2,686
40' 17' - 3" 40' - 0" 43'-10" 1,122 1,220 1,310 1,385 1,483 1,579 1,717 44' 2,115 2,305 2,425 2,624 2,743
SPEED REDUCTION - Sealed worm gear C-face speed reducer with No. 50 roller chain to drive pulleyMOTOR – 1 HP – 230/460 V – 3 phase – 60 Hz totally enclosed fan cooled brake motor, energy effientFRAME CAPACITY – Maximum load per linear foot of conveyor is 225 lbs. Not to exceed drive capacity in chart.
13Roseville, Michigan • Phone: (586) 771-1881 • www.ultimationinc.com
OPTIONAL EQUIPMENTFLOOR SUPPORTS – SMS floor supports are available in wide range of adjustments. Specify top of belt elevation. One support is required at every bed joint and at ends of conveyor. Holes in feet are provided for lagging to floor. Knee braces supplied on SMS-3 support and above.
BELT – Brown polymate roughtop w/ nitrile cover, pure gum rubber roughtop
BELT SPEED – Other constant and variable speeds: 17 - 135 FPM in any increment. Contact factory for speeds not listed above.
MOTORS – Premium energy efficient, single phase, other characteristics. 2 HP maximum.
OTHER DRIVE VARIATIONS • Side mount center drive • End drive with underhung or side mount drive. Requires underside take-up.
PULLEYS – 6 in. dia. tail with 1-3/16 in. dia. shaft at bearing in place of 4 in. when not furnished as standard.
UNDERTRUSSING – Available under incline bed sections in place of floor supports or ceiling hangers. Maximum bed length is 40 ft. Maximum belt width is 24 in. See bed and undertrussing information.
GUIDE RAILS – Adjustable channel guide rails, fixed angle and channel guide rails.
OTHER ACCESSORIES – Ceiling hangers. See accessory section.
ELECTRICAL CONTROLS – One direction manual start switch, reversing drum switch, non-reversing and reversible IEC starters, push button stations, AC variable frequency drive.
8" CENTER DRIVE
SECTION VIEW "X-X"
14Roseville, Michigan • Phone: (586) 771-1881 • www.ultimationinc.com
INCLINE DIMENSIONAL CHART(MODELS BSI & BRI)
DEGREE OF INCLINE
INCLINE BED
LENGTH
7.5° 10° 12.5° 15° 17.5° 20° 22.5° 25° 27.5 30 OVERALL LENGTH
(REF.)VL HF VL HF VL HF VL HF VL HF VL HF VL HF VL HF VL HF VL HF
10 1' - 5" 13' - 9" 1' - 10" 13' - 8" 2' - 4" 13' - 7" 2' - 10" 13' - 5" 3' - 3" 13' - 4" 3' - 8" 13' - 2" 4' - 2" 13' - 0" 4' - 7" 12' - 10" 5' - 0" 12' - 7" 5' - 5" 12' - 4" 13' - 10"
12 1' - 8" 15' - 9" 2' - 3" 15' - 8" 2' - 9" 15' - 6" 3' - 4" 15' - 5" 3' - 10" 15' - 3" 4' - 5" 15' - 1" 4' - 11" 14' - 10" 5' - 5" 14' - 7" 5' - 11" 14' - 4" 6' - 5" 14' - 1" 15' - 10"
14 1' - 11" 17' - 8" 2' - 7" 17' - 7" 3' - 2" 17' - 6" 3' - 10" 17' - 4" 4' - 5" 17' - 2" 5' - 1" 16' - 11" 5' - 8" 16' - 8" 6' - 3" 16' - 5" 6' - 10" 16' - 2" 7' - 5" 15' - 10" 17' - 10"
16 2' - 2" 19' - 8" 2' - 11" 19' - 7" 3' - 8" 19' - 5" 4' - 4" 19' - 3" 5' - 1" 19' - 0" 5' - 9" 18' - 10" 6' - 5" 18' - 6" 7' - 1" 18' - 3" 7' - 9" 17' - 11" 8' - 5" 17' - 7" 19' - 10"
18 2' - 5" 21' - 8" 3' - 3" 21' - 6" 4' - 1" 21' - 4" 4' - 10" 21' - 2" 5' - 8" 20' - 11" 6' - 5" 20' - 8" 7' - 3" 20' - 5" 8' - 0" 20' - 1" 8' - 8" 19' - 8" 9' - 5" 19' - 4" 21' - 10"
20 2' - 8" 23' - 8" 3' - 7" 23' - 6" 4' - 6" 23' - 4" 5' - 5" 23' - 1" 6' - 3" 22' - 10" 7' - 1" 22' - 7" 8' - 0" 22' - 3" 8' - 10" 21' - 10" 9' - 8" 21' - 6" 10' - 5" 21' - 0" 23' - 10"
22 3' - 0" 25' - 8" 3' - 11" 25' - 6" 4' - 11" 25' - 3" 5' - 11" 25' - 0" 6' - 10" 24' - 9" 7' - 10" 24' - 5" 8' - 9" 24' - 1" 9' - 8" 23' - 8" 10' - 7" 23' - 3" 11' - 5" 22' - 9" 25' - 10"
24 3' - 3" 27' - 7" 4' - 4" 27' - 5" 5' - 4" 27' - 3" 6' - 5" 27' - 0" 7' - 6" 26' - 8" 8' - 6" 26' - 4" 9' - 6" 25' - 11" 10' - 6" 25' - 6" 11' - 6" 25' - 0" 12' - 5" 24' - 6" 27' - 10"
26 3' - 6" 29' - 7" 4' - 8" 29' - 5" 5' - 10" 29' - 2" 6' - 11" 28' - 11" 8' - 1" 28' - 7" 9' - 2" 28' - 2" 10' - 3" 27' - 9" 11' - 4" 27' - 4" 12' - 5" 26' - 9" 13' - 5" 26' - 3" 29' - 10"
28 3' - 9" 31' - 7" 5' - 0" 31' - 5" 6' - 3" 31' - 2" 7' - 5" 30' - 10" 8' - 8" 30' - 6" 9' - 10" 30' - 1" 11' - 0" 29' - 7" 12' - 2" 29' - 1" 13' - 4" 28' - 7" 14' - 5" 27' - 11" 31' - 10"
30 4' - 0" 33' - 7" 5' - 4" 33' - 4" 6' - 8" 33' - 1" 8' - 0" 32' - 9" 9' - 3" 32' - 5" 10' - 7" 31' - 11" 11' - 10" 31' - 6" 13' - 0" 30' - 11" 14' - 3" 30' - 4" 15' - 5" 29' - 8" 33' - 10"
32 4' - 3" 35' - 7" 5' - 8" 35' - 4" 7' - 1" 35' - 1" 8' - 6" 34' - 8" 9' - 10" 34' - 4" 11' - 3" 33' - 10" 12' - 7" 33' - 4" 13' - 11" 32' - 9" 15' - 2" 32' - 1" 16' - 5" 31' - 5" 35' - 10"
34 4' - 6" 37' - 6" 6' - 0" 37' - 4" 7' - 6" 37' - 0" 9' - 0" 36' - 8" 10' - 6" 36' - 2" 11' - 11" 35' - 9" 13' - 4" 35' - 2" 14' - 9" 34' - 7" 16' - 1" 33' - 11" 17' - 5" 33' - 2" 37' - 10"
36 4' - 9" 39' - 6" 6' - 5" 39' - 3" 8' - 0" 38' - 11" 9' - 6" 38' - 7" 11' - 1" 38' - 1" 12' - 7" 37' - 7" 14' - 1" 37' - 0" 15' - 7" 36' - 4" 17' - 0" 35' - 8" 18' - 5" 34' - 11" 39' - 10"
38 5' - 1" 41' - 6" 6' - 9" 41' - 3" 8' - 5" 40' - 11" 10' - 1" 40' - 6" 11' - 8" 40' - 0" 13' - 3" 39' - 6" 14' - 10" 38' - 10" 16' - 5" 38' - 2" 17' - 11" 37' - 5" 19' - 5" 36' - 7" 41' - 10"
40 5' - 4" 43' - 6" 7' - 1" 43' - 2" 8' - 10" 42' - 10" 10' - 7" 42' - 5" 12' - 3" 41' - 11" 14' - 0" 41' - 4" 15' - 8" 40' - 8" 17' - 3" 40' - 0" 18' - 10" 39' - 2" 20' - 5" 38' - 4" 43' - 10"
Note: Dimensions “VL” and “HF” are based on 4" tail pulleys. For 6" tail pulleys, overall length increases by 2 inches and dimensions “VL” and “HF” will change slightly. Contact factory if exact dimensions are required.
15Roseville, Michigan • Phone: (586) 771-1881 • www.ultimationinc.com
BED & UNDERTRUSSING INFORMATION(MODELS BRI & BSI)
SECTION VIEW “X-X”
16
TBOH
The TBOH belt conveyor, with its built-in guide rails is ideal for overhead conveying applications or applications where product orientation is not the main focus. Typical products include boxes, cases, cartons, bags or loose parts.
n Smooth, slim design n Coped ends n Troughed bed n 10 belt widths
STANDARD SPECIFICATIONSBELT – Black Trackmate 120 EMBBED – 4 in. deep x 12 ga. powder coated steel slider bed with 2 1/2" deep guides. Standard 5 ft. and 10 ft. long bolt-together sections with splice plates.END DRIVE – Located on discharge end of conveyor. Chain guard is on left hand side when standing at infeed looking toward discharge.DRIVE PULLEY – 4 in. dia. with 1 in. dia. shaft at bearings or 8 in. dia. with 1 7/16 in. dia. shaft at bearings. Machined, crowned and fully lagged.TAIL PULLEY – 4 in. dia. with 1 in. dia. shaft at bearings. Machined crown.SNUB ROLLERS – Adjustable 2 1/2 in. dia. rollers. Grease packed ball bearings. Includes guard.RETURN ROLLERS – Adjustable 1.9 in. dia. rollers. Grease packed ball bearings.TAKE-UP – Provides 4 in. of belt take-up at tail pulleyBEARINGS – Sealed, pre-lubricated, self-aligning, ball bearings on drive and tail pulleysBELT SPEED – Constant 65 FPMSPEED REDUCTION – Sealed worm gear C-face speed reducer with No. 50 roller chain to drive pulleyMOTOR – 1/2 HP – 230/460 V – 3 phase – 60 Hz totally enclosed fan cooled, energy efficientFRAME CAPACITY – Maximum load per linear foot of conveyor is 75 lbs. Not to exceed drive capacity in chart.
TROUGHED BELT CONVEYOR (Overhead Conveying/Parts Handling)
CONVEYOR WEIGHTS (LBS.)
OVERALLLENGTH
BED LENGTH
OVERALLLENGTH
WITHCENTER DRIVE
BELT WIDTH
6" 8" 10" 12" 14" 16" 18" 20" 24" 30"
BETWEEN SIDE GUIDES
7" 9" 11" 13" 15" 17" 19" 21" 25" 31"
OVERALL BED WIDTH
8" 10" 12" 14" 16" 18" 20" 22" 26" 32"
6' 5' 6'
4 I
N.
DIA
. D
RIV
E P
ULLE
Y
235 251 267 283 299 315 331 347 378 418
11' 10' 11' 295 315 335 355 375 395 415 435 475 531
16' 15' 16' 345 369 393 417 440 464 488 512 559 633
21' 20' 21' 413 441 469 497 524 500 528 556 616 733
26' 25' 26' 465 497 529 561 591 558 590 623 691 832
31' 30' 31' 527 563 599 635 669 627 663 700 777 938
36' 35' 36' 510 598 637 678 726 673 712 752 837 1,021
41' 40' 41' 644 687 730 758 816 755 798 843 938 1,143
46' 45' 46' 675 721 737 816 875 800 847 896 998 1,224
51' 50' 51' 758 809 860 911 961 882 933 985 1,095 1,342
56-4" 55' 56'
8 I
N.
DIA
. D
RIV
E P
ULLE
Y
856 909 938 1,029 1,095 1,010 1,069 1,129 1,253 1,529
61-4" 60' 61' 935 998 1,061 1,124 1,185 1,092 1,155 1,220 1,364 1,673
66-4" 65' 66' 974 1,033 1,099 1,167 1,242 1,138 1,204 1,272 1,424 1,754
71-4" 70' 71' 1,055 1,126 1,197 1,268 1,339 1,228 1,289 1,371 1,523 1,866
76-4" 75' 76' 1,093 1,159 1,234 1,311 1,394 1,273 1,338 1,424 1,583 1,947
81-4" 80' 81' 1,169 1,248 1,327 1,406 1,484 1,366 1,434 1,515 1,684 2,071
86-4" 85' 86' 1,177 1,281 1,364 1,449 1,539 1,400 1,483 1,568 1,744 2,152
91-4" 90' 91' 1,214 1,370 1,457 1,544 1,629 1,482 1,569 1,657 1,870 2,327
96-4" 95' 96' 1,325 1,405 1,495 1,587 1,686 1,528 1,618 1,709 1,930 2,408
101-4" 100' 101' 1,414 1,494 1,588 1,682 1,776 1,610 1,704 1,800 2,001 2,472
LOAD CAPACITY (LBS.)
HORIZONTAL W/ STANDARD BELT 25° INCLINEW/ ROUGHTOP
BELTBELTWIDTH
4" DRIVE PULLEY 8" DRIVE PULLEY
FPM HP 11' 31' 51' 77' 101' 11' 31'
35
1/26"-16" 800 790 770 740 720 330 325
18"-30" 790 760 720 680 640 325 315
16"-16" 825*† 1,730* 1,710* 1,690 1,660 725* 715*
18"-30" 825*† 1,690* 1,660* 1,620 1,580 715* 700*
65
1/26"-16" 470 450 430 405 390 195 185
18"-30" 450 420 390 340 300 185 175
16"-16" 825† 1,030 1,010 980 960 435 425
18"-30" 825† 1,000 960 920 880 425 415
26"-16" 825*† 2,090* 2,070* 2,050 2,030 875* 870*
18"-30" 825*† 2,060* 2,030* 1,980 1,950 865* 855*
100
1/26"-16" 325 310 290 265 240 135 125
18"-30" 310 275 245 195 160 130 115
16"-16" 720 705 690 660 640 300 290
18"-30" 710 675 640 595 555 295 280
26"-16" 825† 1,430 1,415 1,390 1,365 600 595
18"-30" 825† 1,400 1,370 1,320 1,280 595 580
135
1/26"-16" 250 235 215 190 170 105 95
18"-30" 235 200 170 120 85 95 85
16"-16" 535 520 500 475 455 225 215
18"-30" 520 485 455 405 370 215 205
26"-16" 825† 1,100 1,085 1,055 1,035 465 455
18"-30" 825† 1,070 1,035 990 950 455 445
* Requires 8" diameter drive pulley in lieu of 4" diameter. †Limited by conveyor capacity.
17Roseville, Michigan • Phone: (586) 771-1881 • www.ultimationinc.com
OPTIONAL EQUIPMENTFLOOR SUPPORTS – SMS floor supports are available in wide range of adjustments. Specify top of belt elevation. One support is required at every bed joint and at ends of conveyor. Holes in feet are provided for lagging to floor. Knee braces supplied on MS-7 support and above.
BELT –Tan Glidetop, White Polymate 100 RMP – COS, Black Trackmate 120 Roughtop with PVC cover
BELT SPEED – Other constant and variable speeds • 4 in. dia. drive pulley: 35, 40, 50, 65, 80, 100 and 135 FPM • 8 in. dia. drive pulley: 35 – 135 FPM in any increment • Contact factory for speeds not listed above
HIGHER SIDES – 4 in., 6 in., 9 in. or 12 in. high vertical sides (12 in. maximum)
OTHER PULLEY OPTIONS • 8 in. dia. drive pulley with 1 7/16 in. dia. shaft at bearings in lieu of 4 in. dia. drive pulley • 6 in. dia. tail pulley with 1 3/16 in. dia. shaft at bearings in lieu of 4 in. dia. tail pulley • 1 1/8 in. dia. nose roller assembly in lieu of 4 in. dia. tail pulley. Center drive is required.
MOTORS – Premium energy efficient, single phase, brake motor, other characteristics. 2 HP maximum.
SHAFT MOUNTED END DRIVE – 4 in. dia. drive pulley only. Drive unit mounted on extended pulley shaft. Mounting bracket and torque arm enable multiple mounting positions. 4 7/8 in. minimum elevation.
4" END DRIVE
8" END DRIVE
CENTER DRIVE / TAKE-UP – Provides 16 in. of belt take-up and is suitable for reversing applications. • Standard underhung drive (4 in. dia. drive pulley): 16 in. minimum elevation. 78 in. minimum OAL. • Standard underhung drive (8 in. dia. drive pulley): 17 in. minimum elevation. 78 in. minimum OAL. • Side mount drive/low elevation center drive (4 in. or 8 in. dia. drive pulley): 13 1/2 in. minimum elevation. 66 in. minimum OAL.
OTHER DRIVE VARIATIONS – Side mounted end or center drives
UNDERSIDE TAKE-UP – Provides 16 in. of belt take-up. Extends down 13 1/8 in. from top of belt.
GRAVITY BRACKETS – Brackets and support bar allows skate wheel or 1 3/8 in. dia. gravity roller conveyor to be supported at end of belt conveyor. Includes 1 in. dia. pop-out transfer roller.
BUTT COUPLINGS – Brackets allow 1.9 in. / 2 in. dia. gravity roller conveyor along with other conveyors to be attached to end of belt conveyor. Includes 1 in. dia. pop-out transfer roller. Center drive or underside take-up recommended if butt couplings are to be located at tail end.
OTHER ACCESSORIES – Floor supports with casters, poly-tier supports, ceiling hangers. See accessory section.
ELECTRICAL CONTROLS – One direction manual start switch, reversing drum switch, non-reversing and reversible IEC starters, push button stations, AC variable frequency drive.
4" SHAFT MOUNTED DRIVESECTION VIEW X - X
OVERALL LENGTH
6"
15-1/2"
MAX.
4-3/4"
22-3/4" 11-1/4"
MAX.
12" APPROX.
34" MAX.
BED LENGTH 6"
FLOW
X
X
OPTIONAL SMS SUPPORT SHOWN
4" DIA. DRIVE PULLEY
2-1/2" DIA.SNUB IDLER
1.9" DIA. RETURN IDLER
TAKE-UP
4" DIA.TAIL PULLEY
NIP POINT GUARD
2-1/2" DIA.SNUB IDLER
NIP POINT GUARD
BED WIDTH
OVERALL BED WIDTH
1/2"
2-1/2"
4"
3-3/4"
BELT WIDTH
2-1/8" DIA.SNUB IDLER
TOTALLY ENCLOSED CHAIN GUARD
L.H.SIDE
R.H.SIDE
10"
9-1/8" 16-1/2"MAX
12" APPROX.
5-5/8"
12-1/2" MAX
39" MAX
28" 11-1/4"MAX
FLOW
OPTIONAL SMSSUPPORT SHOWN
OVERALL LENGTH
BED LENGTH
2-1/2" DIA.SNUB IDLER
8" DIA.DRIVE PULLEY
6"REF.
7-1/8" *MIN. ELEV.
3-1/4"
8-1/8"
18
TBTH
CONVEYOR WEIGHTS (LBS.)
OVERALL LENGTH
BED LENGTH
BELT WIDTH
12" 18" 24" 30" 36" 42" 48" 54"
BETWEEN FRAME WIDTH
13" 19" 25" 31" 37" 43" 49" 55"
OVERALL FRAME WIDTH
16" 22" 28" 34" 40" 46" 52" 58"
4 IN. DIA. TAIL PULLEY 6 IN. DIA. TAIL PULLEY
12' 10' 732 867 1,002 1,137 1,272 1,408 1,542 1,676
22' 20' 974 1,152 1,330 1,508 1,686 1,865 2,042 2,219
32' 30' 1,216 1,437 1,658 1,879 2,100 2,322 2,542 2,762
42' 40' 1,458 1,722 1,986 2,250 2,514 2,779 3,042 3,305
52' 50' 1,700 2,007 2,314 2,621 2,928 3,236 3,542 3,848
62' 60' 1,942 2,292 2,642 2,992 3,342 3,693 4,042 4,391
72' 70' 2,184 2,577 2,970 3,363 3,756 4,150 4,542 4,934
82' 80' 2,426 2,862 3,298 3,734 4,170 4,607 5,042 5,477
92' 90' 2,668 3,147 3,626 4,105 4,584 5,064 5,542 6,020
102' 100' 2,910 3,432 3,954 4,476 4,998 5,521 6,042 6,563
112' 110' 3,152 3,717 4,282 4,847 5,412 5,978 6,542 7,106
122' 120' 3,394 4,002 4,610 5,218 5,826 6,435 7,042 7,649
132' 130' 3,636 4,287 4,938 5,589 6,240 6,892 7,542 8,192
142' 140' 3,878 4,572 5,266 5,960 6,654 7,349 8,042 8,755
152' 150' 4,120 4,857 5,594 6,331 7,068 7,806 8,542 9,278
STANDARD SPECIFICATIONSBELT – Black Trackmate 120 EMB
BED – 7 1/2 in. deep x 1 1/2 in. flange by 12 ga. powder coated steel channel frame with bolt-in slider pans and cross members. 6 in. high guards. Bed sections bolt together with endcaps.
CENTER DRIVE / TAKE-UP – Underhung center drive with chain guard located on left-hand side when standing at infeed looking toward discharge
• DRIVE PULLEY – 8 in. dia. with 1 7/16 in. dia. shaft at bearings. Machined, crowned and fully lagged.
• TAKE-UP PULLEY – 6 in. dia. with 1 3/16 in. dia. shaft at bearings
• TAKE-UP – Provides 16 in. of belt take-up in center drive
TAIL PULLEY - 4 in. dia. with 1 in. dia. shaft at bearings or 6 in. dia. with 1 3/16 in. dia. shaft at bearing. Machined crown.
SNUB ROLLERS – Adjustable 2 1/2 in. dia. rollers. Grease packed ball bearings. Includes guard.
RETURN ROLLERS – Adjustable 1.9 in. dia. rollers. Grease packed ball bearings.
BEARINGS – Sealed, pre-lubricated, self-aligning, ball bearings on drive and tail pulleys
BELT SPEED – Constant 65 FPM
DUST PANS – 16 ga. underside dust cover
SPEED REDUCTION - Sealed worm gear C-face speed reducer with No. 60 roller chain to drive pulley
MOTOR – 1 HP – 230/460 V – 3 phase – 60 Hz totally enclosed fan cooled, energy effieient
FRAME CAPACITY – Maximum load per linear foot of conveyor is 10 lbs. Not to exceed drive capacity in chart.
LOAD CAPACITY CHART (LBS.)
HORIZONTAL
W/ STANDARD BELT
15" INCLINE W/ ROUGHTOP
BELTBELT WIDTHFPM HP 27' 52' 77' 102' 152' 27' 52'
35
124"-36" 1,906 1,863 1,822 1,779 1,695 1,024 1,000
48"-54" 1,870 1,806 1,744 1,680 1,555 1,004 970
224"-36" 3,172 3,129 3,088 3,045 2,961 1,073 1,680
48"-54" 3,136 3,072 3,010 2,946 2,820 1,684 1,649
65
124"-36" 991 948 907 864 780 532 601
48"-54" 955 891 829 766 640 513 565
224"-36" 1,673 1,630 1,589 1,546 1,461 898 875
48"-54" 1,637 1,573 1,511 1,447 1,321 879 845
100
124"-36" 617 575 533 490 406 331 309
48"-54" 582 518 456 392 266 309 278
224"-36" 1,060 1,018 976 933 849 569 546
48"-54" 1,025 961 899 835 709 550 516
135
124"-36" 438 395 353 311 226 235 212
48"-54" 402 338 276 212 86 216 181
224"-36" 766 723 681 639 554 411 388
48"-54" 730 666 604 540 414 392 357
TROUGHED BELT CONVEYOR (Trash Handling)
With its 6 in. high guide rails and minimal belt gap between guide rails, the TBOH belt conveyor is ideal for handling empty cardboard boxes and paper trash.
n Troughed bed n 8 belt widths n Center drive and take-up
19Roseville, Michigan • Phone: (586) 771-1881 • www.ultimationinc.com
SECTION VIEW X-X
OPTIONAL EQUIPMENTFLOOR SUPPORTS – SMS floor supports are available in wide range of adjustments. Specify top of belt elevation. One support is required at every bed joint and at ends of conveyor. Holes in feet are provided for lagging to floor.
BELT – Black Trackmate 120 Roughtop with PVC cover
BELT SPEED – Other constant and variable speeds: 17-135 FPM in any increment. Contact factory for speeds not listed above.
PULLEYS - 6 in. dia. tail pulley with 1 3/16 in. dia. shaft at bearings in place of 4 in. when not furnished
MOTORS – Inverter duty, premium energy efficient, single phase, brake motor, other characteristics. 2 HP maximum.
SIDE MOUNTED CENTER DRIVE / TAKE-UP – Provides 16 in. of belt take-up and is suitable for reversing applications. 12 1/2 in. minimum elevation. 66 in. minimum OAL.
UNDERSIDE TAKE-UP – Provides 16 in. of belt take-up. Extends down 13 1/8 in. from top of belt.
8 IN. END DRIVE – Requires underside take-up • Underhung end drive: 16 1/2 in. minimum elevation. 103 in. minimum OAL. • Side mount end drive: 10 in. minimum elevation. 95 in. minimum OAL.
INCLINE WITH NOSE-OVER AND INFEED - 5, 10, 12-1/2, 15, or 20 degree (See drawing below)
• NOSE-OVER – Fixed degree nose-over section providing transition from incline to horizontal
• TWO-PULLEY HITCH – Fixed degree section providing transition from horizontal infeed to incline while allowing one belt to be used for infeed and incline
HIGHER GUIDE RAILS – 12 in., 18 in., or 24 in. high vertical sides. 30 degree flare is also available.
ELECTRICAL CONTROLS – One direction manual start switch, reversing drum switch, non-reversing and reversible magnetic starters, push button stations, AC variable frequency drive.
INCLINE WITH NOSE-OVER AND INFEED
FLOW
OVERALL FRAME WIDTH