42
i BIDDING DOCUMENTS (PROCUREMENT OF GOODS) SUPPLY AND DELIVERY OF HINO 700 Dump Trucks (18 CBM Tipper Body) Prepared by IOM Mission in South Sudan 20 April 2016 FPU.SF- 19.10
i
BIDDING DOCUMENTS (PROCUREMENT OF GOODS)
SUPPLY AND DELIVERY OF
HINO 700 Dump Trucks (18 CBM Tipper Body)
Prepared by
IOM Mission in South Sudan
20 April 2016
FPU.SF- 19.10
ii
Table of Contents
Section I. Instructions to Bidders ........................................................................................... 4
Section II. Schedule of Requirements .................................................................................... 6
Section III. Technical Specifications ..................................................................................... 23
Section IV. Contract for Supply and Delivery of Goods…….. ............................................. 26
Section V. Sample Forms ...................................................................................................... 35
3
INVITATION FOR BIDS
IFB No. : JUB-CTS-20042016
20 April 2016
The International Organization for Migration (IOM) is an intergovernmental organization
established in 1951 and is committed to the principle that humane and orderly migration
benefits both migrants and society.
In the framework of Common Transport Services in South Sudan, the IOM Bids Evaluation
and Awards Committee (“BEAC”) now invites interested Bidders to submit “Bid” for the
supply and delivery of UN MOSS Compliance trucks
Item
No. Item Description Quantity Unit
1 Hino 700 series 6x4 dump trucks
(18 CBM tipper body) ZS1EPVA 3 item
A complete set of Bidding Documents is available for issuance to Interested Bidders at on
IOM website https://www.iom.int/procurement-opportunities until Wednesday 4 May 2016.
Bids shall be valid for a period of forty five (45) calendar days after submission of Bids and
must be accompanied by a Bid Security equivalent to not less than 2.5% of the Bidders Total
Bid Price in the form of bank guarantee and shall be delivered to the BEAC at IOM Mission
in South before Thursday 5 May 2016.
Submission of Bids is due Friday 5 May2016 at 17.00 pm. Late bids shall be rejected. Bids
will be opened at the address specified in the following session, on Friday, 6 May 2016 at
10:00 in the presence of the Bidders who wish to attend.
IOM reserves the right to accept or reject any bids, and to cancel the procurement process and
reject all bids at any time prior to award of Contract, without obligation to inform the affected
Bidder/s of the ground for IOM action.
Sincerely yours,
Karl Baker
BEAC Chairperson
IOM is encouraging companies to use recycled materials or materials coming from
sustainable resources or produced using a technology that has lower ecological footprints.
4
Section I. Instructions to Bidders
5
Table of Clauses
A. General ............................................................................................................................. 6
1. Scope of Bid ................................................................................................... 6
2. Eligible Bidders ............................................................................................. 6
3. Corrupt, Fraud ................................................................................................. 6
4. Eligible Goods and Services .......................................................................... 7
B. The Bidding Documents................................................................................................... 8
5. Content of Bidding Documents ..................................................................... 8
6. Clarification of Bidding Documents .............................................................. 8
7. Amendment of Bidding Documents .............................................................. 8
C. Preparation of Bids ........................................................................................................... 8
8. Cost of Bidding .............................................................................................. 9
9. Language of Bid ............................................................................................. 9
10. Documents Comprising the Bid ..................................................................... 9
11. Bid Form ........................................................................................................ 9
12. Bid Prices ....................................................................................................... 9
13. Bid Currencies ............................................................................................... 11
14. Documents Establishing Bidder’s Eligibility and Qualification .................... 11
15. Documents Establishing Goods’ Eligibility and Conformity to Bidding
Documents ..................................................................................................... 11
16. Period of Validity of Bids .............................................................................. 12
18 Format and Signing of Bid ............................................................................. 13
D. Submission of Bids .......................................................................................................... 14
19. Sealing and Marking of Bids ......................................................................... 14
20. Deadline for Submission of Bids ................................................................... 14
21. Late Bids ........................................................................................................ 14
22. Modification and Withdrawal of Bids ........................................................... 15
E. Opening and Evaluation of Bids....................................................................................... 15
23. Opening of Bids ............................................................................................. 15
24. Clarification of Bids and Contacting IOM..................................................... 15
25. Preliminary ..................................................................................................... 16
26. Conversion to Single Currency (if applicable) .............................................. 16
27. Evaluation and Comparison of Bids .............................................................. 16
28. Clarification of Bids and Contacting IOM..................................................... 18
29. Post-qualification ........................................................................................... 18
30. Purchaser’s Right to Accept any Bid and to Reject any or All Bids ............. 19
F. Award of Contract ............................................................................................................ 19
31. Award Criteria ............................................................................................... 19
32. Purchaser’s Right to Vary Quantities at Time of Award ............................... 19
33. Notification of Award .................................................................................... 19
34. Performance Security ..................................................................................... 19
35. Signing of Contract ........................................................................................ 20
6
Instructions to Bidders
A. General
1. Scope of Bid
1.1 IOM invites bids for the supply and delivery of 3 units of Hino
700 Dump Trucks (Tipper trucks) hereto referred as Goods. The
Goods is specified in greater details in the Sub Section of the Bid
Documents.
1.2 The successful Bidder is expected to complete the delivery by
the Intended Completion Date which is (60) sixty calendar days
after signature of Contract.
2. Eligible
Bidders
2.1 This Invitation for Bids is open to all Bidders from eligible
source countries.
2.2 Bidders should not be associated, or have been associated in the
past, directly or indirectly, with a firm or any of its affiliates
which have been engaged by IOM to provide consulting services
for the preparation of the design, specifications, and other
documents to be used for the procurement of the goods to be
purchased under this Invitation for Bids.
2.3 Government-owned enterprises in IOM’s Mission country
Mission may participate only if they are legally and financially
autonomous, if they operate under commercial law, and if they
are not a beneficiary of IOM.
2.4 Bidders shall not be under a declaration of ineligibility for
corrupt, fraudulent and coercive practices issued by IOM in
accordance with ITB Clause 3
2.5 Bidders shall not be involved in terrorist act/criminal activities or
associated with individuals and/or entities associated with
terrorist act/criminal activities. For this purpose, Bidders shall
not be included in the proscribed list of individuals and/or
entities as contained in the 1267 Committee of the UN Security
Council Counter Terrorism Committee (CTC)
3. Corrupt,
Fraudulent,
Collusive and
Coercive
Practices
3.1 IOM requires that all IOM Staff, Bidders, Manufacturers,
suppliers or distributors, observe the highest standard of ethics
during procurement and execution of all contracts. IOM shall
reject any Bids put forward by Bidders or where applicable
terminate their contract, if it is determined that they have
engaged in corrupt, fraudulent, collusive or coercive practices. In
pursuance of this policy, IOM :
(a) defines, for the purposes of this provision, the terms set
forth below as follows:
7
(i) “corrupt practice” means the offering, giving,
receiving or soliciting directly or indirectly any
thing of value to influence the action of the
Procuring/Contracting Entity in the procurement
process or in contract execution;
(ii) “fraudulent practice” is any acts or omission,
including a misrepresentation, that knowingly
or recklessly misleads, or attempts to mislead,
the Procuring/Contracting Entity in the
procurement process or the execution of a
contract, to obtain a financial gain or other
benefit to avoid an obligation;
(iii) “collusive practice” is an undisclosed
arrangement between two or more Bidders
designed to artificially alter the results of the
tender procedure to obtain a financial gain or
benefit;
(iv) “coercive practice” is impairing or harming, or
threatening to impair or harm, directly or
indirectly, any participant in the tender process
to influence improperly its activities in a
procurement process, or after the execution of a
contract.
(b) will reject a proposal for award if it determines that the
Bidder recommended for award has engaged in corrupt,
fraudulent, collusive or coercive practices in competing
for the contract in question;
(c) will declare a firm ineligible, either indefinitely or for a
stated period of time, to be awarded an IOM financed
contract if it at any time determines that the firm has
engaged in corrupt, fraudulent, collusive or coercive
practices in competing for, or in executing, an IOM
financed contract.
4. Eligible Goods
and Services
4.1 All goods and related services to be supplied under the contract
shall have their origin in eligible source countries, and all
expenditures made under the contract will be limited to such
goods and services.
4.2 For purposes of this clause, “origin” means the place where the
goods are mined, grown, or produced, or the place from which
the related services are supplied. Goods are produced when,
through manufacturing, processing, or substantial and major
assembly of components, a commercially recognized product
results that is substantially different in basic characteristics or in
8
purpose or utility from its components.
4.3 The origin of goods and services is distinct from the nationality
of the Bidder.
B. The Bidding Documents
5. Content of
Bidding
Documents
5.1 The goods required, bidding procedures, and contract terms are
prescribed in the bidding documents. In addition to the
Invitation for Bids, the bidding documents include:
a) Instructions to Bidders (ITB)
b) Contract for Supply and Delivery of Goods
c) Schedule of Requirements
d) Technical Specifications
e) Sample Forms
5.2 The Bidder is expected to examine all instructions, forms, terms,
and specifications in the bidding documents. Failure to furnish
all information required in the bidding documents or to submit a
bid not substantially responsive to the bidding documents in
every respect will be at the Bidder’s risk and may result in the
rejection of its bid.
6. Clarification of
Bidding
Documents
6.1 A prospective Bidder requiring any clarification of the bidding
documents may notify IOM in writing at Sirilak (Ewe)
Wichayaruangrom [email protected] and copy [email protected].
IOM will respond in writing to any request for clarification of the
bidding documents, which it receives no later than (3) three days
prior to the deadline for the submission of bids.
7. Amendment of
Bidding
Documents
7.1 At any time prior to the deadline for submission of bids, IOM,
for any reason, whether at its own initiative or in response to a
clarification requested by a prospective Bidder, may modify the
bidding documents by amendment.
7.2 All prospective bidders that have received the bidding documents
will be notified of the amendment in writing and will be binding
on them.
7.3 In order to allow prospective bidders reasonable time in which to
take the amendment into account in preparing their bids, IOM, at
its discretion, may extend the deadline for the submission of
bids.
C. Preparation of Bids
9
8. Cost of
Bidding
8.1 The Bidder shall bear all costs associated with the preparation
and submission of its bid, and IOM will in no case be responsible
or liable for those costs, regardless of the conduct or outcome of
the bidding process.
9. Language of
Bid
9.1 The bid prepared by the Bidder, as well as all correspondence
and documents relating to the bid exchanged by the Bidder and
IOM, shall be written in English language. Supporting
documents and printed literature furnished by the Bidder may be
in another language provided they are accompanied by an
accurate translation of the relevant passages in the required
language, in which case, for purposes of interpretation of the Bid,
the translation shall govern.
10. Documents
Comprising
the Bid
10.1 The bid prepared by the Bidder shall comprise the following
components:
(a) a Bid Form and a Price Schedule completed in accordance
with ITB Clauses 11, 12, and 13;
(b) documentary evidence established in accordance with ITB
Clause 14 that the Bidder is eligible to bid and is qualified
to perform the contract if its bid is accepted;
(c) documentary evidence established in accordance with ITB
Clause 15 that the goods and ancillary services to be
supplied by the Bidder are eligible goods and services and
conform to the bidding documents; and
(d) bid security furnished in accordance with ITB Clause 17.
11. Bid Form
11.1 The Bidder shall complete the Bid Form and the appropriate
Price Schedule furnished in the bidding documents, indicating
the goods to be supplied, a brief description of the goods, and
their country of origin, quantity, and prices.
12. Bid Prices 12.1 The Bidder shall indicate on the appropriate Price Schedule the
unit prices and total bid price of the goods it proposes to supply
under the contract.
12.2 Prices indicated on the Price Schedule shall be entered separately
in the following manner:
(a) For goods offered from within IOM’s Mission country:
(i) the price of the goods quoted EXW (ex works, ex
factory, ex warehouse, ex showroom, or off-the-shelf,
as applicable), including all customs duties and sales
and other taxes already paid or payable:
10
a. on the components and raw material used in the
manufacture or assembly of goods quoted ex
works or ex factory;
or
b. on the previously imported goods of foreign
origin quoted ex warehouse, ex showroom, or
off-the-shelf.
(ii) any sales and other taxes which will be payable on the
goods if the contract is awarded.
(iii) the price for inland transportation, insurance, and
other local costs incidental to delivery of the goods to
their final destination
(iv) the price of other (incidental) services, if any
(b) For goods offered from abroad:
(i) the price of the goods shall be quoted in DAP IOM
Office Juba, South Sudan. In quoting the price, the
Bidder shall be free to use transportation through
carriers registered in any eligible countries.
Similarly, the Bidder may obtain insurance services
from any eligible/acceptable source.
(ii) the price for inland transportation, insurance, and
other local costs incidental to delivery of the goods
from the port of entry to their final destination
(iii) the price of (incidental) services, if any.
12.3 The INCOTERM shall be governed by the rules prescribed in the
current edition of INCOTERMS.
12.4 The Bidder’s separation of price components in accordance with
ITB Clause 12.2 above will be solely for the purpose of
facilitating the comparison of bids by IOM and will not in any
way limit IOM’s right to contract on any of the terms offered.
12.5 Prices quoted by the Bidder shall be fixed during the Bidder’s
performance of the contract and not subject to variation on any
account, unless otherwise specified. A bid submitted with an
adjustable price quotation will be treated as non-responsive and
will be rejected, pursuant to ITB Clause 25. If, however,
specified in these instructions, prices quoted by the Bidder shall
11
be subject to adjustment during the performance of the contract,
a bid submitted with a fixed price quotation will not be rejected,
but the price adjustment would be treated as zero.
13. Bid Currencies 13.1 Prices shall be quoted in the following currencies:
For goods and services that the Bidder will supply from
within or outside IOM’s Mission country, the prices shall be
quoted in USD currency.
14. Documents
Establishing
Bidder’s
Eligibility and
Qualification
14.1 Pursuant to ITB Clause 10.1b, the Bidder shall furnish, as part of
its bid, documents establishing the Bidder’s eligibility to bid and
its qualifications to perform the contract if its bid is accepted (the
IOM Vendor Information Sheet (VIS) can be used for this
purpose).
14.2 The documentary evidence of the Bidder’s eligibility to bid shall
establish to IOM’s satisfaction that the Bidder, at the time of
submission of its bid, is from an eligible country as defined
under ITB Clause 4.
14.3 The documentary evidence of the Bidder’s qualifications to
perform the contract if its bid is accepted shall establish to IOM’s
satisfaction:
(a) that, in the case of a Bidder offering to supply goods under
the contract which the Bidder did not manufacture or
otherwise produce, the Bidder has been duly authorized by
the goods’ Manufacturer or producer to supply the goods in
IOM’s Mission country;
(b) that the Bidder has the financial, technical, and production
capability necessary to perform the contract;
(c) that, in the case of a Bidder not doing business within
IOM’s Mission country, the Bidder is or will be (if awarded
the contract) represented by an Agent in that Mission
country equipped, and able to carry out the Supplier’s
maintenance, repair, and spare parts-stocking obligations
prescribed in the Conditions of Contract and/or Technical
Specifications
14.4 If the Bidder wishes to use the existing VIS or Company Profile
on file to establish their eligibility, the Bidders should submit
with their bids any information updating their original VIS or
company profile on file or, alternatively, confirm in their bids
that the originally submitted information remains essentially
correct as of the date of bid submission.
15. Documents 15.1 Pursuant to ITB Clause 10, the Bidder shall furnish, as part of its
12
Establishing
Goods’
Eligibility and
Conformity to
Bidding
Documents
bid, documents establishing the eligibility and conformity to the
bidding documents of all goods and services, which the Bidder
proposes to supply under the contract.
15.2 The documentary evidence of the eligibility of the goods and
services shall consist of a statement in the Price Schedule of the
country of origin of the goods and services offered, which shall
be confirmed by a certificate of origin issued at the time of
shipment.
15.3 The documentary evidence of conformity of the goods and
services to the bidding documents may be in the form of
literature, drawings, and data, and shall consist of:
(a) a detailed description of the essential technical and
performance characteristics of the goods;
(b) a list giving full particulars, including available sources and
current prices of spare parts, special tools, etc., necessary
for the proper and continuing functioning of the goods,
following commencement of the use of the goods by IOM;
and
(c) an item-by-item commentary on IOM’s Technical
Specifications demonstrating substantial responsiveness of
the goods and services to those specifications, or a
statement of deviations and exceptions to the provisions of
the Technical Specifications.
15.4 For purposes of the commentary to be furnished pursuant to ITB
Clause 15.3(c) above, the Bidder shall note that standards for
workmanship, material, and equipment, as well as references to
brand names or catalogue numbers designated by IOM in its
Technical Specifications, are intended to be descriptive only and
not restrictive. The Bidder may substitute alternative standards,
brand names, and/or catalogue numbers in its bid, provided that
it demonstrates to IOM’s satisfaction that the substitutions ensure
substantial equivalence to those designated in the Technical
Specifications.
16. Period of
Validity of
Bids
Bids shall remain valid for the period of (30) thirty days after the
date of bid opening prescribed by IOM, pursuant to ITB Clause
20. A bid valid for a shorter period shall be rejected by IOM as
non-responsive.
In exceptional circumstances, prior to expiry of the bid validity,
IOM may request that the bidders extend the period of validity
for a specified additional period not more than 60 days. The
request and the bidders’ responses shall be made in writing.
13
A Bidder may refuse the request without forfeiting the Bid
Security. A Bidder agreeing to the request will not be required
nor permitted to modify the Bid, but will be required to extend
the validity of Bid Security for the period of the extension, and in
compliance with Clause 17 in all respects.
17. Bid Security 17.1 Pursuant to ITB Clause 10, the Bidder shall furnish, as part of its
bid, a bid security in the amount 2.5% of the total bid amount.
17.2 The bid security is required to protect IOM against the risk of
Bidder’s conduct, which would warrant the security’s forfeiture,
pursuant to ITB Clause 17.6. The bid security shall be
denominated in USD in the form of bank guarantee.
17.3 Any bid not secured in accordance with ITB Clauses 17.1 will be
rejected by IOM as non-responsive, pursuant to ITB Clause 25.
17.4 Unsuccessful bidders’ bid security will be discharged or returned
as promptly as possible but not later than thirty (30) days after
the expiration of the period of bid validity prescribed by IOM
pursuant to ITB Clause 16.
17.5 The successful Bidder’s bid security will be discharged upon the
Bidder signing the contract, pursuant to ITB Clause 35, and
furnishing the performance security, pursuant to ITB Clause 34.
17.6 The bid security may be forfeited:
(a) if a Bidder withdraws its bid during the period of bid
validity specified by the Bidder on the Bid Form; or
(b) in the case of a successful Bidder, if the Bidder fails:
(i) to sign the contract in accordance with ITB Clause
35;
or
(ii) to furnish performance security in accordance with
ITB Clause 34.
18 Format and
Signing of Bid
18.1 The Bidder shall prepare an Original and 2nd Copy of the bid,
clearly marking each “ORIGINAL BID” and “COPY OF BID,”
as appropriate. In the event of any discrepancy between them,
the original shall govern.
18.2 The original and the copy or copies of the bid shall be typed or
written in indelible ink and shall be signed by the Bidder or a
person or persons duly authorized to bind the Bidder to the
contract. All pages of the bid, shall be initialed by the person or
persons signing the bid.
14
18.3 Any interlineations, erasures, or overwriting shall be valid only if
they are initialed by the person or persons signing the bid.
D. Submission of Bids
19. Sealing and
Marking of
Bids
19.1 The Bidder shall seal the original and each copy of the bid in
separate envelopes, duly marking the envelopes as “ORIGINAL
BID” and “COPY OF BID.” The envelopes shall then be sealed
in an outer envelope.
19.2 The inner and outer envelopes shall:
(a) be addressed to IOM at the address given below
IOM Juba, New Industrial Area, Northern Bari, Juba,
South Sudan
;and
(b) bear the Project name, the Invitation for Bids (IFB) title
and reference number, and a statement: “DO NOT OPEN
BEFORE 10:00 am on 3 May 2016.
19.3 The inner and outer envelopes shall also indicate the name and
address of the Bidder to enable the bid to be returned unopened
in case it is declared “late”.
19.4 If the outer envelope is not sealed and marked as required by ITB
Clause 19.2, the bid will still be considered, however, IOM will
assume no responsibility for the bid’s misplacement or premature
opening.
20. Deadline for
Submission of
Bids
20.1 Bids must be received by IOM at the address specified under ITB
Clause 19.2.a no later than 5 May 2016 at 17:00 pm.
20.2 IOM may, at its discretion, extend this deadline for the
submission of bids by amending the bidding documents in
accordance with ITB Clause 7, in which case all rights and
obligations of IOM and bidders previously subject to the
deadline will thereafter be subject to the deadline as extended.
21. Late Bids 21.1 Any bid received by IOM after the deadline for submission of
bids prescribed by IOM pursuant to ITB Clause 20 will be
rejected and returned unopened to the Bidder.
21.2 The Bidder will assume the responsibility and expenses for the
re-possession of the returned bid documents.
15
22. Modification
and
Withdrawal of
Bids
22.1 The Bidder may modify or withdraw its bid after the bid’s
submission, provided that written notice of the modification,
including substitution or withdrawal of the bids, is received by
IOM prior to the deadline prescribed for submission of bids.
22.2 The Bidder’s modification or withdrawal notice shall be
prepared, sealed, marked, and dispatched in accordance with the
provisions of ITB Clause 18. A withdrawal notice will be in
writing and should be received by IOM not later than the
deadline for submission of bids.
22.3 No bid may be modified after the deadline for submission of
bids.
22.4 No bid may be withdrawn in the interval between the deadline
for submission of bids and the expiration of the period of bid
validity specified by the Bidder on the Bid Form. Withdrawal of
a bid during this interval may result in the Bidder’s forfeiture of
its bid security, pursuant to the ITB Clause 17.6.
E. Opening and Evaluation of Bids
23.Opening of
Bids
23.1 IOM will open all bids in the presence of bidders’ representatives
who choose to attend, at the time, on the date, and at the place
specified herein at 10:00 am on 6 May 2016 at IOM Juba New
Industrial Area, Northern Bari, Juba, South Sudan. The bidders’
representatives who are present shall sign a register evidencing
their attendance.
23.2 The bidders’ names, bid modifications or withdrawals, bid
prices, discounts, and the presence or absence of requisite bid
security and such other details that IOM at its discretion, may
consider appropriate, will be announced at the opening. No bid
shall be rejected at bid opening, except for late bids, which shall
be returned unopened to the Bidder pursuant to ITB Clause 21.
23.3 Bids (and modifications sent pursuant to ITB Clause 22.2) that
are not opened and read out at bid opening shall not be
considered further for evaluation, irrespective of the
circumstances. Withdrawn bids will be returned unopened to the
bidders.
23.4 IOM will prepare minutes of the bid opening.
24. Clarification of
Bids and
Contacting
IOM
During evaluation of the bids, IOM may, at its
discretion, ask the Bidder for a clarification of
its bid. The request for clarification and the
response shall be in writing, and no change in
the prices or substance of the bid shall be
16
sought, offered, or permitted.
25. Preliminary
Examination
IOM will examine the bids to determine
whether they are complete, whether any
computational errors have been made, whether
required sureties have been furnished, whether
the documents have been properly signed, and
whether the bids are generally in order.
25.2 Arithmetical errors will be rectified on the following basis. If
there is a discrepancy between the unit price and the total price
that is obtained by multiplying the unit price and quantity, the
unit price shall prevail, and the total price shall be corrected. If
the Supplier does not accept the correction of the errors, its bid
will be rejected, and its bid security may be forfeited. If there is
a discrepancy between words and figures, the amount in words
will prevail.
25.3 IOM may waive any minor informality, nonconformity, in a bid
which does not constitute a material deviation, provided such
waiver does not prejudice or affect the relative ranking of any
Bidder.
25.4 Prior to the detailed evaluation, pursuant to ITB Clause 27,
IOM will determine the substantial responsiveness of each bid to
the bidding documents. For purposes of these Clauses, a
substantially responsive bid is one, which conforms to all the
terms and conditions of the bidding documents without material
deviations. Deviation from, or objection or reservations to
critical provisions, such as those concerning Bid Security (ITB
Clause 17), Price Schedule (ITB Clause 9) will be deemed to be
a material deviation. IOM’s determination of a bid’s
responsiveness is to be based on the contents of the bid itself
without recourse to extrinsic evidence.
25.5 If a bid is not substantially responsive, it will be rejected by
IOM and may not subsequently be made responsive by the
Bidder by correction of the nonconformity.
26. Conversion to
Single
Currency (if
applicable)
26.1 To facilitate evaluation and comparison, IOM will convert all bid
prices expressed in the amounts in various currencies in USD
according to IOM exchange rate for the current month and year.
27. Evaluation and
Comparison of
Bids
27.1 IOM will evaluate and compare the bids, which have been
determined to be substantially responsive, pursuant to ITB
Clause 25.
27.2 IOM’s evaluation of a bid will exclude and not take into
account:
17
(a) in the case of goods manufactured in IOM’s Mission
country or goods of foreign origin already located in IOM’s
Mission country, sales and other similar taxes, which will
be payable on the goods if a contract is awarded to the
Bidder;
(b) in the case of goods of foreign origin offered from abroad,
customs duties and other similar import taxes which will be
payable on the goods if the contract is awarded to the
Bidder; and
(c) any allowance for price adjustment during the period of
execution of the contract, if provided in the bid.
27.3 The comparison shall be between the EXW price of the goods
offered from within IOM’s Mission country, such price to
include all costs, as well as duties and taxes paid or payable on
components and raw material incorporated or to be incorporated
in the goods, and the CIF named port of destination (or CIP
border point, or CIP named place of destination) price of the
goods offered from outside IOM’s Mission country.
27.4 IOM’s evaluation of a bid will take into account, in addition to
the bid price quoted in accordance with ITB Clause 12.2, one or
more of the following factors:
(a) cost of inland transportation, insurance, and other costs
within IOM’s Mission country incidental to delivery of the
goods to their final destination.
(b) delivery schedule offered in the bid;
(c) deviations in payment schedule from that specified in the
Conditions of Contract;
(d) the cost of components, mandatory spare parts, and service;
(e) the availability in IOM’s Mission country of spare parts
and after-sales services for the equipment offered in the
bid;
(f) the projected operating and maintenance costs during the
life of the equipment;
(g) the performance and productivity of the equipment offered;
and/or
(h) other specific criteria indicated and/or in the Technical
Specifications
18
Alternative (if
applicable)
27.5 Merit Point System:
The following merit point system for weighing evaluation factors
can be applied if none of the evaluation methods listed above has
been retained. The number of points allocated to each factor
shall be specified.
[choose from the range of]
Evaluated price of the goods 60 to 90
Cost of common list spare parts 0 to 20
Technical features, and maintenance
and operating costs 0 to 20
Availability of service and spare parts 0 to 20
Standardization 0 to 20
Total 100
The bid scoring the highest number of points will be deemed to
be the lowest evaluated bid.
28. Clarification of
Bids and
Contacting
IOM
28.1 Subject to ITB Clause 24, no Bidder shall contact IOM on any
matter relating to its bid, from the time of the bid opening to the
time the contract is awarded. If the Bidder wishes to bring
additional information to the notice of IOM, it should do so in
writing.
28.2 Any effort by a Bidder to influence IOM in its decisions on
bid evaluation, bid comparison, or contract award may result in
the rejection of the Bidder’s bid.
29. Post-
qualification
29.1 In the absence of pre-qualification, IOM will determine to its
satisfaction whether the Bidder that is selected as having
submitted the lowest evaluated responsive bid is qualified to
perform the contract satisfactorily, in accordance with the criteria
listed in ITB Clause 14.
29.2 The determination will take into account the Bidder’s
financial, technical, and production capabilities. It will be based
upon an examination of the documentary evidence of the
Bidder’s qualifications submitted by the Bidder, pursuant to ITB
Clause 14, as well as such other information as IOM deems
necessary and appropriate.
29.3 Prior to award, IOM shall verify and validate any
documents/information submitted and if necessary shall
conduct ocular inspection of the Bidder office, plant/warehouse
and equipment .
29.3 An affirmative determination will be a pre-requisite for award of
19
the contract to the Bidder. A negative determination will result
in rejection of the Bidder’s bid, in which event IOM will proceed
to the next lowest evaluated bid to make a similar determination
of that Bidder’s capabilities to perform satisfactorily.
30. Purchaser’s
Right to
Accept any Bid
and to Reject
any or All Bids
30.1 IOM reserves the right to accept or reject any bid, and to annul
the bidding process and reject all bids at any time prior to
contract award, without thereby incurring any liability to the
affected Bidder or bidders or any obligation to inform the
affected Bidder or bidders of the grounds for IOM’s action.
F. Award of Contract
31. Award
Criteria
31.1 IOM will award the contract to the successful Bidder whose bid
has been determined to be substantially responsive and has been
determined to be the lowest evaluated bid, provided further that
the Bidder is determined to be qualified to perform the contract
satisfactorily.
32. Purchaser’s
Right to Vary
Quantities at
Time of Award
32.1 IOM reserves the right at the time of contract award to increase
or decrease, by the percentage indicated [+/- 15%] the quantity
of goods and services originally specified in the Schedule of
Requirements without any change in unit price or other terms
and conditions.
33. Notification of
Award
33.1 Prior to the expiration of the period of bid validity, IOM will
notify the successful Bidder in writing, that its bid has been
accepted.
33.2 The notification of award will constitute the formation of the
Contract.
33.3 Upon the successful Bidder’s furnishing of the performance
security pursuant to ITB Clause 35, IOM will promptly notify
each unsuccessful Bidder and will discharge its bid security,
pursuant to ITB Clause17.
34. Performance
Security
34.1 Within five (5) days of the receipt of notification of award from
IOM, the successful Bidder shall furnish a performance security
equivalent to 10% of the Contract Price in accordance with the
Conditions of Contract, in the form provided in the bidding
documents, or in another form acceptable to IOM.
34.2 Failure of the successful Bidder to comply with the requirement
of ITB Clause 33 or ITB Clause 34.1 shall constitute sufficient
grounds for the annulment of the award and forfeiture of the bid
security, in which event IOM may make the award to the next
lowest evaluated Bidder or call for new bids.
20
35. Signing of
Contract
35.1 At the same time as IOM notifies the successful Bidder that its
bid has been accepted, IOM will send the Bidder the Contract
provided in the bidding documents, incorporating all agreements
between the parties.
35.2 Within five (5) days of receipt of the Contract, the successful
Bidder shall sign and date the contract and return it to IOM.
21
Section II. Schedule of Requirements
22
Schedule of Requirements
PROJECT TITLE : Supply of 3 units Hino 700 dump truck (18 cbm tipper body)
Item
No.
Description of Goods Quantity Unit Related Services
Required
Reference Drawing
/Specifications
Delivery Schedule Delivery Place
1
Hino 700 series
ZS1EPVA 6x4 dump
trucks (18 cbm tipper
body)
3
n/a
see Sec. III technical
specification
30 June 2016
Juba, South Sudan
23
Section III. Technical Specifications
24
Technical Specifications
Manufacturer : HINO
Origin : Japan
Model : Hino 700 ZS1EPVA 6x4 18 CBM Dump truck
(18 cbm Tipper Body)
S P E C I F I C A T I O N S O F H I N O Z S 1 E P V A 6 x 4 C H A S S I S*
Options required for each Hino truck:
2 spare wheel including carriage
Codan Bracket
Inflating Hose
Transit Safety box
M A K E & T Y P E Z S 1 E P V A 6 X 4 C H A S S I S Dump truck (Tipper Body)
COUNTRY OF ORIGIN HINO CHASSIS FROM JAPAN.
GVW
CAB
39500 Kg
Forward Control, day cabin with A/C & Radio Cassette Player. Seating: 1 Driver + 1 co-driver.
DIMENSIONS (mm) OL- 8,235
OH- 3,210
OW-2,555
WB- 4,145+1,500
ROH-1,200
CA- 3,850
ENGINE 6 Cylinder, In-line, Engine, Water-cooled, 410 HP Diesel Engine with Turbocharging and intercooling, Electronically controlled Common Rail injection. Euro 3 Standard. Power: 410 HP @ 1800 rpm; Torque: 1618 Nm @ 1100 rpm
TRANSMISSION ZF16S151, Sixteen speed overdrive synchromesh 1st-16th,
TIPPER BODY Volume 18 CBM
All welded steel construction
TYRES 12.00 R 24 Internationally reputed branded Tires
(Including Spare Tire)
BRAKES Full Air Dual Circuit, S Cam Drum Type WITH engine Retarder
Auxiliary & Parking Brake: Spring brake acting on front and rear frontward wheels for emergency and parking purpose.
FUEL TANK 300 Litres
OTHERS Standard toolkit
Operators Manual
COLOUR WHITE CAB
* Hino 700 series catalog
25
Tipper box design may vary as long as the volume capacity
Spare wheel # 1 Spare wheel # 2
Bracket for Codan radio
26
Section IV. Contract for Supply and Delivery of Goods
27
FPU.SF 19.18
**This is a template Contract for Supply and Delivery of Goods and may need to be modified
according to the specific requirements of the Mission. As per IOM policy, all Contracts must
be reviewed/approved by Legal Services prior to signing.
**If subcontracting, please check the donor agreement for any donor requirement regarding
a subcontract. (i.e. use of donor’s logo, reporting requirements, anti-corruption clause or
any particular provision to be inserted in a subcontract etc.)
IOM Office-specific Ref. No.: XXXXX
IOM Project code: XXXXX
LEG Approval/Checklist Code: XXXXX
CONTRACT FOR THE SUPPLY AND DELIVERY OF GOODS
Between
The International Organization for Migration
And
[Name of the Other Party]
This Contract for the Supply and Delivery of Goods (“Contract”) is entered into between the
International Organization for Migration (“IOM”) of [insert address] represented by [insert
Name, Title of Chief of Mission ], hereinafter referred to as IOM, and [Name of the Other
Party] of [insert address], represented by [insert Name, Title of the representative of the
Other Party], hereinafter referred to as the the Supplier on [insert date].
1. Introduction and Integral Documents
The Supplier agrees to provide IOM with [insert description of goods] in
accordance with the terms and conditions of this Contract and its Annexes, if
any.
The following documents form an integral part of this Contract: [add or delete
as required]
Bid/Quotation Form
Price Schedule
Delivery Schedule and Technical Specifications
Accepted Notice of Award (NOA)
Performance Security
28
2. Goods/Services Supplied
2.1. The Supplier agrees to supply to IOM the Goods in strict accordance with the
specifications, and at the price stated for each item outlined below:
No.
Description
Project
budget line/
WBS
Qty
Unit
Unit Price
Total
2.2 The Supplier agrees to supply the following incidental services: [add or delete as
required]
(a) performance or supervision of on-site assembly and/or start-up of the supplied
Goods;
(b) furnishing of tools required for assembly and/or maintenance of the supplied
Goods;
(c) furnishing of a detailed operations and maintenance manual for each appropriate
unit of the supplied Goods;
(d) performance, supervision, maintenance and/or repair of the supplied Goods, for a
period of time agreed by the parties, provided that this service shall not relieve the
Supplier of any warranty obligations under this Contract; and
(e) training of IOM’s personnel, at the Supplier’s plant and/or on-site, in assembly,
start-up, operation, maintenance, and/or repair of the supplied Goods.
3. Charges and Payment
3.1 The total Price for the supply and delivery of the Goods and any Incidental Services
under this Contract is XXX [write in figures and then in words, including currency]
3.2 The Supplier shall invoice IOM on delivery of the Goods in accordance with this Contract
and payment shall become due 30 calendar days after acceptance by IOM of the Goods.
3.3 The invoice will be accompanied by the following documents: Air Way Bill number,
shipping invoice, packing list, certificate of origin [add or delete as required]
3.4 Payments shall be made in [currency] by bank transfer to the following bank account of
the Supplier: [bank account details].
3.5 The Price specified in clause 3.1 is the total charge to IOM. The Supplier shall be
responsible for the payment of all taxes, duties, levies and charges assessed on it in
connection with this Contract.
3.6IOM shall be entitled, without derogating from any other right it may have, to defer
payment of part or all of the Price until the Supplier has completed, to the satisfaction of
IOM, the delivery of the Goods and the incidental services to which those payments
relate.
29
4. Delivery
4.1 The Goods shall be delivered to: [insert place of delivery] on [insert delivery schedule]
by [insert method of delivery or refer to Delivery Schedule annexed]. Cost of delivery is
deemed included in the Price specified in clause 3.1 of this Contract. The incidental
services as described in clause 2.2 shall be performed at the place of delivery and
completed by the same delivery date, unless otherwise stated in clause 2.2 of this
Contract.
4.2 In the event of breach of this clause IOM reserves the right to:
(a) Terminate this Contract without liability by giving an immediate notice and to charge
the Supplier with any loss incurred as a result of the Supplier's failure to make the
delivery within the time specified; or
(b) Charge a penalty of 0.1% of the total contract price for every day of delay or breach
of the delivery schedule by the Supplier.
5. Performance Security (applicable for contracts over USD250,000)
5.1 The Supplier shall furnish IOM with a Performance Security in the amount equivalent to
[ten (10)] percent of the Contract Price, to be issued by a reputable bank or company, and
in the format acceptable to IOM.
5.2 The Performance Security shall serve as the guarantee for the Supplier’s faithful
performance and compliance with the terms and conditions of this Contract. The amount
of the Performance Security shall not be construed as the limit of the Supplier’s liability
to IOM, in the event of breach of this Contract by the Supplier. The Performance Security
shall be effective until [insert a date 30 days from the completion of Supplier’s
obligations] following which it will be discharged by IOM.
6. Inspection and Acceptance
6.1 Where any annexed Technical Specifications state what inspections and tests are required
and where they will be carried out, those terms will prevail in the event of any
inconsistency with the provisions in this clause.
6.2 IOM or its representative shall have the right to inspect and/or test the goods at no extra
cost to IOM at the premises of the Supplier, at the point of delivery or at the final
destination. The Supplier shall facilitate such inspections and provide required assistance.
6.3 IOM shall have 30 calendar days after proper receipt of the Goods purchased to inspect
them and either accept or reject them as non-conforming with this Contract. Based on an
inspection of a valid sample, IOM may reject the entire delivery. IOM may also charge
the cost of inspecting rejected Goods to the Supplier. All rejected Goods will be returned
to the Supplier, transportation charges collect, or held by IOM for disposition at
Supplier's risk and expense. IOM’s right to reject the Goods shall not be limited or
waived by the Goods having been previously inspected or tested by IOM prior to
delivery.
6.4 The Supplier agrees that IOM’s payment under this Contract shall not be deemed
acceptance of any Goods delivered hereunder.
6.5 The Supplier agrees that any acceptance by IOM does not release the Supplier from any
warranty or other obligations under this Contract.
30
6.6 Title to the Goods shall pass to IOM when they are delivered and accepted by IOM. Risk
of loss, injury, or destruction of the Goods shall be borne by the Supplier until title passes
to IOM.
7. Adjustments
7.1 IOM reserves the right to change at any time the quantities, packaging, unit size, place,
method and/or time of delivery or the ancillary services to be provided. Where Goods are
being specifically produced for IOM, IOM may also make changes to the drawings,
designs or specifications.
7.2 The Supplier agrees to proceed with this Contract in accordance with any such change(s)
and to submit a claim request for an equitable adjustment in the Price or delivery terms
caused by such change(s).
7.3 IOM may deem any claim by the Supplier for equitable adjustments under this clause
waived unless asserted in writing within 10 days from the date of receipt by the Supplier
of IOM’s change(s).
7.4 No change in, modification of, or revision to this Contract shall be valid unless made in
writing and signed by an authorized representative of IOM.
8. Packaging
8.1 The Supplier must provide proper and adequate packaging in accordance with best
commercial practice, to ensure that the Goods being delivered to IOM will be free of
damage. Packaging must be adequate to allow for rough handling during transit, exposure
to extreme temperatures, salt and precipitation during transit and open storage, with
consideration for the type of Goods and transportation mode. IOM reserves the right to
reject any delivery that is deemed not to have been packaged adequately.
8.2 Packing, marking and documentation shall comply with any requirements or instructions
notified by IOM.
9. Warranties
9.1 The Supplier warrants that all Goods supplied under this Contract shall have no defect,
arising from design, materials, or workmanship or from any act or omission of the
Supplier that may develop under normal use of the supplied Goods in the conditions
prevailing in the country of final destination. This warranty shall remain valid for twelve
(12) months after the Goods have been delivered to and accepted at the final destination
indicated in the Contract.
9.2 The Supplier warrants that all Goods supplied under this Contract are new, unused, of the
most recent or current models and that they incorporate all recent improvements in design
and materials unless provided otherwise in this Contract. All Goods/Services delivered
under this Contract will conform to the specifications, drawings, samples, or other
descriptions furnished or specified by IOM.
9.3 IOM shall promptly notify the Supplier in writing of any claims arising under this
warranty.
9.4 Upon receipt of such notice, the Supplier shall, within the time period specified in the
notice, repair or replace the defective Goods or parts thereof, without cost to IOM.
9.5 IOM’s continued use of such Goods after notifying the Supplier of their defect or failure
to conform or breach of warranty will not be considered a waiver of the Supplier’s
warranty.
31
9.6 The Supplier further represents and warrants that:
(a) It has full title to the Goods, is fully qualified to sell the Goods to IOM, and is a
company financially sound and duly licensed, with adequate human resources,
equipment, competence, expertise and skills necessary to carry out fully and
satisfactorily, within the stipulated completion period, the delivery of the Goods in
accordance with this Contract;
(b) It shall comply with all applicable laws, ordinances, rules and regulations when
performing its obligations under this Contract;
(c) In all circumstances it shall act in the best interests of IOM;
(d) No official of IOM or any third party has received or will be offered by the Supplier
any direct or indirect benefit arising from this Contract or award thereof;
(e) It has not misrepresented or concealed any material facts in the procuring of this
Contract;
(f) The Supplier, its staff or shareholders have not previously been declared by IOM
ineligible to be awarded contracts by IOM;
(g) It shall abide by the highest ethical standards in the performance of this Contract,
which includes not engaging in any discriminatory or exploitative practice or practice
inconsistent with the rights set forth in the Convention on the Rights of the Child;
(h) The prices for the Goods under this Contract do not exceed those offered for similar
goods to Supplier’s other customers;
(i) The Price specified in clause 2.1 of this Contract shall constitute the sole
remuneration of the Supplier in connection with this Contract. The Supplier shall not
accept for its own benefit any trade commission, discount or similar payment in
connection with activities pursuant to this Contract or the discharge of its obligations
hereunder. The Supplier shall ensure that any subcontractors, as well as the personnel
and agents of either of them, similarly, shall not receive any additional remuneration.
9.7 The Supplier further warrants that:
(a) It shall take all appropriate measures to prevent actual, attempted or threatened sexual
exploitation or abuse (SEA) by its employees or any other persons engaged and
controlled by it to perform any activities under this Agreement. In addition, it shall
take all appropriate measures to prohibit its employees or other persons engaged and
controlled by it from exchanging any money, goods, or services at their disposal under
this Agreement, for sexual favours or activities.
(b) It shall strongly discourage sexual relationships between its employees and IOM
beneficiaries, and between any other person engaged and controlled by it to perform
activities under this Agreement and IOM beneficiaries.
(c) It shall take all appropriate measures to ensure that its employees or any other persons
engaged and controlled by it to perform any activities under this Agreement do not
engage in sexual activity with children (persons under the age of 18) regardless of the
age of majority or age of consent locally. Mistaken belief regarding the age of a child
is not a defence. This prohibition shall not apply where the employee or other person
engaged and controlled by it to perform activities under this Agreement is legally
married to someone under the age of 18 but over the age of majority or consent in their
country of citizenship.
(d) It shall report all and any complaints or concerns regarding possible SEA by its
employees, any other persons engaged and controlled by it to perform any activities
under this Agreement, or IOM personnel; and it shall take all appropriate measures to
ensure that its employees or any other persons engaged and controlled by it to perform
32
any activities under this Agreement shall report to IOM and/or the Supplier any
complaints or concerns regarding possible SEA by its employees, any other persons
engaged and controlled by it to perform any activities under this Agreement, or IOM
personnel.
(e) It shall take all necessary measures to investigate allegations or suspicions of SEA
and take appropriate corrective action, including disciplinary action, against its
employee or any other person engaged and controlled by it to perform any activities
under this Agreement who is found to have committed SEA.
(f) Its failure to take preventive measures against SEA, to duly report any complaints or
concerns about SEA to IOM, to investigate allegations thereof, or to take corrective
action when SEA has occurred, shall constitute grounds for termination of this
Agreement.
(g) In the event of subcontracting approved by IOM in accordance with this Agreement, it
shall receive a written confirmation from subcontractors that they accept the standards
above and shall include them in all subcontracts.
10. Termination and Re-procurement
10.1 IOM may terminate this Contract, in whole or in part, at any time with written notice
to the Supplier. Any monies paid in advance by IOM shall be refunded on or before the
date of termination.
10.2 If IOM terminates this Contract in whole or in part for default on the part of the
Supplier, it may acquire elsewhere goods similar to those terminated and the Supplier
shall be liable for any excess costs to IOM for the re-procurement of those Goods as well
as the removal of any or all of the Supplier’s product or equipment from IOM’s premise
or other places of delivery. The Supplier shall not be liable for any excess costs if the
failure to perform under this Contract arises from causes beyond its control and without
fault or negligence of the Supplier.
10.3 Upon any such termination, the Supplier shall waive any claims for damages including
loss of anticipated profits on account thereof.
11. Force Majeure
Neither Party will be liable for any delay in performing or failure to perform any of its
obligations under this Contract if such delay or failure is caused by force majeure, such as
civil disorder, military action, natural disaster and other circumstances which are beyond
the control of the Party in question. In such event, the party will give immediate notice in
writing to the other Party of the existence of such cause or event and of the likelihood of
delay.
12. Indemnification and Insurance
12.1 The Supplier shall at all times defend, indemnify, and hold harmless IOM, its officers,
employees, and agents from and against all losses, costs, damages and expenses
(including legal fees and costs), claims, suits, proceedings, demands and liabilities of
any kind or nature to the extent arising out of or resulting from acts or omissions of
the Supplier or its employees, officers, agents or subcontractors, in the performance of
this Contract. IOM shall promptly notify the Supplier of any written claim, loss, or
demand for which the Supplier is responsible under this clause.
33
12.2 This indemnity shall survive the expiration or termination of this Contract.
12.3 The Goods supplied under this Contract shall be fully insured in a freely convertible
currency against loss or damage resulting from or related to manufacture or
acquisition, transportation, storage, and delivery. Further insurance requirements may
be specified in the Technical Specifications.
13. Independent Contractor
The Supplier shall provide the Goods under this Contract as an independent contractor and
not as an employee, partner, or agent of IOM.
14. Audit
The Supplier agrees to maintain financial records, supporting documents, statistical records
and all other records in accordance with generally accepted accounting principles to
sufficiently substantiate all direct and indirect costs of whatever nature involving transactions
related to the supply and delivery of Goods and incidental services under this Contract. The
Supplier shall make all such records available to IOM or its designated representative at all
reasonable times until the expiration of seven (7) years from the date of final payment, for
inspection, audit, or reproduction. On request, employees of the Supplier shall be available
for interview.
15. Dispute Resolution
Any dispute, controversy or claim arising out of or in relation to this Contract, or the
breach, termination or invalidity thereof, shall be settled amicably by negotiation
between the Parties. In the event that such negotiation is unsuccessful, either Party may
submit the dispute to arbitration. The arbitration will be carried out in accordance with
the UNCITRAL arbitration rules. The arbitral award will be final and binding.
16. Confidentiality
All information which comes into the Supplier’s possession or knowledge in connection
with this Contract is to be treated as strictly confidential. The Supplier should not
communicate such information to any third party without the prior written approval of
IOM. The Supplier shall comply with IOM Data Protection Principles in the event that
it collects, receives, uses, transfers or stores any personal data in the performance of this
Contract. These obligations shall survive the expiration or termination of this Contract.
17. Notices
Any notice given pursuant to this Contract will be sufficiently given if it is in writing
and delivered, or sent by prepaid post or facsimile to the other Party at the following
address:
[Insert IOM address]
[Insert Supplier’s address]
18. Use of IOM’s Name
34
The official logo and name of IOM may only be used by the Supplier in connection with
this Contract and with the prior written approval of IOM.
19. Status of IOM
Nothing in this Contract affects the privileges and immunities enjoyed by IOM as an
intergovernmental organization.
20. Assignment and Subcontracting
20.1 The Supplier shall not assign or subcontract the Contract or any work under this
Contract in part or all, unless agreed upon in writing in advance by IOM. Any
subcontract entered into by the Supplier without approval in writing by IOM may be
cause for termination of the Contract.
20.2 In certain exceptional circumstances by prior written approval of IOM, specific jobs
and portions of the Contract may be assigned to a subcontractor. Notwithstanding the
said written approval, the Supplier shall not be relieved of any liability or obligation
under this Contract nor shall it create any contractual relation between the
subcontractor and IOM. The Supplier remains bound and liable there under and it
shall be directly responsible to IOM for any faulty performance under the subcontract.
The subcontractor shall have no cause of action against IOM for any breach of the
subcontract.
21. Waiver
Failure by either Party to insist in any one or more instances on a strict performance of
any of the provisions of this Contract shall not constitute a waiver or relinquishment of
the right to enforce the provisions of this Contract in future instances, but this right shall
continue and remain in full force and effect.
22. Severability
If any part of this Contract is found to be invalid or unenforceable, that part will be
severed from this Contract and the remainder of the Contract shall remain in full force.
23. Entirety
This Contract and any Annexes embody the entire agreement between the Parties and
supersede all prior agreements and understandings, if any, relating to the subject matter of
this Contract.
24. Final Clauses
24.1 This Contract will enter into force upon signature by both Parties and shall remain in
force until completion of all obligations of the Parties under this Contract.
24.2 Amendments to this Contract may be made by mutual agreement in writing between
the Parties.
Signed in two copies in English , on (date) at (place).
35
For: The International Organization For: (Name of Supplier)
for Migration
(name) _ (name)
(title) ___(title
36
Section V. Sample Forms
37
Table of Forms
1. Suppliers Bid Form ……………………………………………… ……………………..40
2. Price Schedule Form ………………………………...…………………………………..41
3. Manufacturers Authorization Form ………………………………………………...…...42
4. Performance Security Form (Bank Guarantee )…………………………….…………. 43
5. Advance Payment Security Form (Bank Guarantee) ……………………..……………44
38
Form-1
BID FORM
Date: ____________
To: The Chairperson
Bids Evaluation and Award Committee (BEAC)
International Organization for Migration
[insert Mission address]
We, the undersigned, declare that;
Having examined the Bidding Document for the [insert project name and IFB No.], issued on
[insert date], the receipt of which is hereby duly acknowledge, I, representing [insert name of
company] offer to complete the Supply and Deliver the GOODS in conformity with the
Bidding Document for the total fixed lump sum price of [insert total bid amount in words
and figures and currency].
I undertake, if my Bid is accepted, to deliver and supply the Goods in accordance with the
Price Schedule and Goods specifications set out in the Bidding Document.
If my Bid is accepted, I will obtain the guarantee of a bank in a sum equivalent to 10% of the
total amount of the Contract Price for the due performance of the Contract, in the form
prescribed by IOM.
I agree to abide by this Bid for the Bid Validity Period specified in the Bidding Document
which may be accepted at any time before the expiration of that period.
Until a formal contract is prepared and executed, the Bid, together with your written
acceptance thereof and the Notice of Award, shall constitute a binding agreement between us.
I hereby certify that the Bid complies with the requirements stipulated in the Bidding
Document.
Dated this ______________day of__________________20___.
________________________ ________________________________
[signature over printed name] [in the capacity of]
Duly authorized to sign Bid for and on behalf of [name of company]
39
Form-2
PRICE SCHEDULE
Item
No.
Description of
Goods
Country of
Origin
Qty/Unit Unit Price
(EXW/CIF/DDU)
Please specify
Transportation/
Handling Cost
Taxes if
Applicable
Total Price
per Item
Name of Bidder: ________________________
Signature of Bidder: _____________________
Date: ________________________________
40
Form -3
MANUFACTURER’S AUTHORIZATION FORM
[See Clause 13.3 (a) of the Instructions to Bidders.]
To:
WHEREAS [name of the Manufacturer] who are established and reputable
manufacturers of [name and/or description of the goods] having factories at [address
of factory]
do hereby authorize [name and address of Agent] to submit a bid, and subsequently
negotiate and sign the Contract with you against IFB No. [reference of the Invitation
to Bid] for the above goods manufactured by us.
We hereby extend our full guarantee and warranty as per Clause 16 of the Conditions
of Contract for the goods offered for supply by the above firm against this Invitation
for Bids.
_______________________________________
[signature for and on behalf of Manufacturer]
Note: This letter of authority should be on the letterhead of the Manufacturer and
should be signed by a person competent and having the power of attorney to
bind the Manufacturer. It should be included by the Bidder in its bid.
41
Form-4
PERFORMANCE SECURITY (Bank Guarantee)
To: [name and address of Employer]
WHEREAS [name and address of Supplier] (hereinafter called “the Supplier”) has
undertaken, in pursuance of Contract No. [number] dated [date] to execute [name of
Contract and brief description of Goods] (hereinafter called “the Contract”);
AND WHEREAS it has been stipulated by you in the said Contract that the Supplier
shall furnish you with a Bank Guarantee by a recognized bank for the sum specified
therein as security for compliance with his obligations in accordance with the
Contract;
AND WHEREAS we have agreed to give the Supplier such a Bank Guarantee;
NOW THEREFORE we hereby affirm that we are the Guarantor and responsible to
you, on behalf of the Supplier, up to a total of [amount of Guarantee] [amount in
words], such sum being payable in the types and proportions of currencies in which
the Contract Price is payable, and we undertake to pay you, upon your first written
demand and without cavil or argument, any sum or sums within the limits of [amount
of Guarantee] as aforesaid without your needing to prove or to show grounds or
reasons for your demand for the sum specified therein.
We hereby waive the necessity of your demanding the said debt from the Supplier
before presenting us with the demand.
We further agree that no change or addition to or other modification of the terms of
the Contract or of the Goods to be performed thereunder or of any of the Contract
documents which may be made between you and the Supplier shall in any way release
us from any liability under this Guarantee, and we hereby waive notice of any such
change, addition, or modification.
This Guarantee shall be valid until a date 28 days from the date of issue of the
Certificate of Completion.
Signature and seal of the Guarantor
Name of Bank
Address
Date
42
Form-5
ADVANCE PAYMENT SECURITY (Bank Guarantee)
To: [name and address of IOM Mission]
Contract : [name of Contract]
Gentlemen:
We have been informed that [name of Supplier] (hereinafter called "the Supplier") has
entered into Contract No. [reference number of the contract] dated [insert date] with
you, for the supply of [brief description of goods & related services] (hereinafter
called "the Contract").
Furthermore, we understand that, according to the conditions of the Contract, an
advance payment in the sum of [amount in figures & in words] is to be made against
an advance payment guarantee
At the request of the Supplier, we [name of Bank] hereby irrevocably undertake to
pay you any sum or sums not exceeding in total an amount of [amount in figures and
in words]1 upon receipt by us of your first demand in writing accompanied by a
written statement stating that the Supplier are in breach of their obligation under the
Contract because the Supplier have used the advance payment for purposes other than
toward providing the required Goods and Services under the Contract.
We further agree that no change or addition to or other modification of the terms of
the Contract or of Goods to be supplied thereunder or of any of the Contract
documents which may be made between [name of IOM Mission] and the Supplier,
shall in any way release us from any liability under this Guarantee, and we hereby
waive notice of any such change, addition, or modification.
This Guarantee shall remain valid and in full effect from the date of the advance
payment under the Contract until [name of IOM Mission] receives full repayment of
the same amount from the Supplier.
Yours truly,
Signature and seal: _____________________________
Name of Bank/Financial Institution: ___________________________
Address: __________________________________
Date: ___________________________________
1 The Guarantor shall insert an amount representing the amount of the advance payment and
denominated either in the currency of the advance payment as specified in the Contract, or in a freely
convertible currency acceptable to IOM.
