U.S. Patent No. 6,088,053. Other patents pending 8x32 Binocular & Digital Camera Model #72212 System Requirements: 1. Window 98/ 98SE/ ME/ 2000/ XP 2. The processor above Pentium 233MHz 3. 128MB SDRAM 4. Video(VGA) card with 2MB of RAM for minimum 16-bit (High Color) display. 5. CD-ROM 6. USB port 7. 600MB of free hard disk space. Digital Camera Specifications Image sensor Lens Field of View Image Resolution (Still Image) Video Resolution Image Capacity Image Type Video measure Digital Zoom Exposure White Balance Memory LCD open angle Language select Interface TV-out Power Source 2.0 Mega pixels, CMOS sensor 300mm(8X) 7 -8 HI -2048x1536 (3.1) MI -1600x1200 (2.0) LO -640x480 (0.3) 320x240, 12 Fps AVI format HI 36 P MI 46 P LO 250 P (*Upon 16MB Flash Memory) MPEG format 6~8 min 4 X Auto / Manual Mode Auto Built-in 16MB Flash Memory SD/MMC card socket expandable 0 / 105 English USB 1.1 NTSC / PAL 1.5V AAA alkaline battery x 4 Binocular specifications Size Field of View Exit pupil Close Focusing Eye Relief Coatings 8 x 32 mm Field of View5.6°Field of view : 92.7m(304 ft) at 914m(1000 YDS) 4.0 mm 3.5 m 12.5 mm Multi coating on the first surface. Single layer for other surface, fully coated. USB Cable User Guide Video Cable Software CD Pouch Binocular Dimensions x 1 x 1 x 1 x 1 x1 156mm x 102mm x 60mm(LCD Close) Package Contents
Transcript
U.S. Patent No. 6,088,053. Other patents pending
8x32Binocular & Digital Camera
Model #72212
System Requirements:1. Window 98/ 98SE/ ME/ 2000/ XP2. The processor above Pentium 233MHz
3. 128MB SDRAM
4. Video(VGA) card with 2MB of RAM forminimum 16-bit (High Color) display.
5. CD-ROM6. USB port
7. 600MB of free harddisk space.
Digital Camera Specifications
Image sensor
Lens
Field of View
Image Resolution
(Still Image)
Video Resolution
Image Capacity
Image Type
Video measure
Digital Zoom
Exposure
White Balance
Memory
LCD open angle
Language select
Interface
TV-out
Power Source
2.0 Mega pixels, CMOS sensor
300mm(8X)
7 -8
HI -2048x1536 (3.1)
MI -1600x1200 (2.0)
LO -640x480 (0.3)
320x240, 12 Fps AVI format
HI 36 P
MI 46 P
LO 250 P
(*Upon 16MB Flash Memory)
MPEG format
6~8 min
4 X
Auto / Manual Mode
Auto
Built-in 16MB Flash Memory
SD/MMC card socket expandable
0 / 105
English
USB 1.1
NTSC / PAL
1.5V AAA alkaline battery x 4
Binocular specifications
Size
Field of View
Exit pupil
Close Focusing
Eye Relief
Coatings
8 x 32 mm
Field of View5.6°Field of view :
92.7m(304 ft) at 914m(1000 YDS)
4.0 mm
3.5 m
12.5 mm
Multi coating on the first surface.
Single layer for other surface, fully coated.
USB Cable
User Guide
Video Cable
Software CD
Pouch
Binocular Dimensions
x 1
x 1
x 1
x 1
x1
156mm x 102mm x 60mm(LCD Close)
Package Contents
Steps to view TV images
1. TV and dedicated Video cable. 2. Plug the dedicated Video cable into the TV out port of VistaPix.
3. Connect the dedicated Video cable to AV terminal of the TV (video side).
4. Press power button. The screen will jump to browsing screen.
5. Press Up-down button to view images on TV.
Power Button
MO
DE
De
l
SE
T/O
K
P.19
AV port
Video cable
Viewing (Movie) recorded images on PC
1. Use the USB cable to connect the USB port from PC to VistaPix.After
connection the "PC" display on LCD.
P.18
2. Double click "MY COMPUTER"
on the PC's desktop.
3. Double click "Removable Device".
4. Open \DCIM\100scope\ 5. Select the video file (*.AVI) and
double click it, the images video
will play through "Windows Media
Player" software or other software.
In order to use Windows Media Player to view the video AVI file taken with your VistaPix, the computer viewing the AVI file needs to be running Microsoft DirectX version 8.0a or later. If you experience problems viewingAVI files from Media Player you can upgrade DirectX to the most current version by going to the Microsoft DirectX Web Page at: www.microsoft.com/windows/directx/default.aspx
Follow the download instructions given on the web site. The download is free.
Warning:
Avoid using under combustibility gas environment.Do not look at the sun with the Binocular, which will damage the eyes
even lead to blindness.Please take care when using the hanging tape, and do not let children
twist it around their necks and bodies to avoid danger due to improper operation.
Please don't throw the product with the gallus in hand to avoid damage to others or malfunction of the product.
Keep the product away from babies to prevent them from putting the batteries or silica gels into their mouths, which causes danger.
Usage of the battery
Please always use Alkaline Battery (AAA Alkaline Battery)Please take out the batteries and keep them separately with the product
if you'll not use the product for a long time.
About usage
Do Not place the product under the following environments to avoid any damage.
o 1.Places in temperature higher that 70C 2.Damp or dusty places 3.Places with strong electromagnetic field.
Please do not disassemble or repair the product to avoid malfunction.Please do not drop the product to the ground to avoid malfunction.
Cautions
Never immerse VistaPix into any fluid or liquid. Remove dust or stains with a soft cloth dampened with water or neutral detergent. Keep in a dry and cool dust-free environment or a container when it is not used.
Take the batteries out when VistaPix is not to be used over a long period.Avoid dropping the VistaPix. Do not disassemble VistaPix.
Cautions
1 24 3
65 7
8
1.To execute Photo Manager. Select the buttons as indicated.
2.Enter " Removable Disk " to open "DCIM" file.
5.Images download finished.
3.In " DCIM " file, open"100MEDIA " data file.
4.In " 100MEDIA " Data file, choose the pictures you want or choose all Images.
How To Use the PhotoManagerSelect the buttons as indicated. "Help" will give you detailed information on Photo Manager's many features. To learn more about Photo Mangaer you can click on the Icon (3) in the lower left side of the screen to directly to the PhotoManager web site www.photo-diy.com.tw/
After installing VistaPix driver & software. Please restart your computer.
Steps to install Photo Manager
P.1
1.Introduction
VistaPix is a binocular integrated with a digital camera that is great
for sporting events, concerts and wildlife activities such a s huntin g o r
bird-watching. VistaPix lets you record memories and sights a t the
touch of a button. Use the full-featured binocula r fo r close r views an d
capture images to take home with you at the same time.
VistaPix makes it possible to share your fun with others by
downloading images from the camera right to your computer
to e-mail to your friends and family.
Battery installation manner1. Hold tight the bottom of battery cover, and lift to open. 2. Install four AAA batteries into the battery compartment as shown below.
7.The serial number is located on the front of the CD.Press "Next" when complete
1. Insert the CD ROM
6.After confirming, please press "Yes"
P.2
Looking at or near the sun will cause instant and irreversible damageto your eye. Eye damage is often painless, so there is no warning tothe observer that damage has occurred until it is too late. Do notpoint the binocular at or near the sun.Children should always have adult supervision while observing.
WARNING !Never use a VistaPix to look at the sun !
2.Notice to User
SD card lid closed SD card lid opened
Foil face up
2-1. When no action is performed with your binocular, the VistaPix will
automatically turn off after 90 seconds.
2-2. The VistaPix has a battery level display in the right lower corner of
the LCD. When the battery is low you will hear a long "beep". If no
action is taken , VistaPix will automatically turn-off after 10 seconds.
2-3. Please use alkaline battery for this product.
2-4. VistaPix comes with a SD card slot that enables you to expand the
memory. To install an optional SD card:
Open the cover of the SD card slot and install the card (with the
gold strips facing up) into the SD card slot (7) until it clicks into the
position.
P.14
After installing VistaPix driver. Please restart your computer.
5. Computer will automatically install the driver.
6. If you see the "Microsoft digital sign" request appear on screen as you are installing the driver , please press "Yes" button to continue installing.
P.13
1.Before you install the driver, please make sure that your VistaPix is not connected to the computer.
1. Insert the CD included with your VistaPix.
2. Click the mouse on "Installation Driver" to begin installation.
3. Begin "InstallShield Wizard" and your computer will automatically execute the installation of driver program.
4. Follow the "InstallShield Wizard" steps to guide you through the driver installation. Click on "Next" when complete.
Steps to install VistaPix driver
2.If you have windows ME/ 2000/ XP operation system installed in your computer, you should not need to install the VistaPix driver. Simply view and save images through your My Computer icon.
P.4
Memory & Image Download
Download imagesWhen downloading the photos, the internal memory and the card memory must be downloaded separately.
Download from flash memoryTake out the SD card (if necessary) and connect the to the computer,then follow the downloading steps and all the photos in the flashmemory can be downloaded.
Download from Optional SD card Insert the SD card and connect the to the computer, then follow the downloading steps and all the photos in the SD card memory can bedownloaded.
Using SD memory cardThe VistaPix has built in flash memory, so when you take images, the images will be saved into the flash memory inside your VistaPix until
memory is full.
Whenever you insert an optional SD memory card to take images, thetaken with the SD card and flash memory are stored separately.
So when downloading the images, the internal flash memory and the memory must be downloaded separately.
the
images
card
(Once the SD card memory is full, you can remove the card and continue the VistaPix until the internal memory is full as well).to use
P.12
7.Basic maintenanceo o o o
Operating Environment: 41 to104 F(5 to 40 C). 20%-85% relativehumidity,non-condensing.
Care of your VistaPix
7 -1.Never immerse VistaPix into any fluid or liquid. Remove dust or stains
with a soft cloth dampened with water or neutral detergent. Keep in a dry
and cool dust-free environment when not in use.
7 -2.Take the batteries out when VistaPix is not to be used over a long
period.
7 -3. Avoid dropping the VistaPix. Do not disassemble VistaPix.
P.5
4.Using the Camera
Use this product under good lighting conditions, avoid facing light source directly. Remember to keep a distance of at least 49 feet (15 meters) awayfrom the target when taking a photo. As you press the "Shutter/Set" button, hold the binocular very steady until you hear a "Beep" sound. If the binocular is unsteady, the camera will not focus well and blurred images will result.
Function
1
2
3
45
6
7
/U
PD
OW
N/
MO
DE
De
l
SE
T/O
K
5
4
3
2
1
NO INDICATORS ITEMS
1 Power / menu
2 Movie / delete
3 Shutter / OK
4 Zoom in / up
5 Zoom out / down
Button
NO INDICATORS ITEMS
1
2 Image resolution0.3MP, 2.0MP, 3.0MP
3 Movie mode
4 SD card mode
5 Auto shooting mode
6 Battery level
7 Memory gauge
Monitor
4-1 Turn on the power by pressing button for 3 seconds and you will hear
two beep sounds. The monitor will display picture number and resolution.
Press again to power off.
4-2 Press Up-down button to zoom in and out. It can magnify the image
up to 32x as seen on the LCD display.
4-3 Press the Shutter button to take pictures. Shooting is completed when
you hear a beep sound.
4-4 Press the Movie button and a beep sound will signal that recording
has begun. The green power indicator light will blink while recording is in
progress. Press the Movie button again to stop recording.
Number of Images Remaining
P.6
Play backAuto shutterSettingPower off
Play backAuto shutterSettingPower off
MEMUMEMU
One eraseErase allOne eraseErase all
ERASEERASE
YesNoYesNo
ONE ERASEONE ERASE
YesNoYesNo
ERASE ALLERASE ALL
One eraseErase allOne eraseErase all
ERASEERASE
Play backAuto shutterSettingPower off
Play back
SettingPower off
Auto shutter
MEMUMEMU
Play backAuto shutterSettingPower off
Play backAuto shutter
Power offSetting
MEMUMEMU
(Play back mode)Press the Menu button , select "Play Back" and press OK button. Use Up-Down button to select the pictures, press OK button to display the picture in full screen. Press the Shutter button again to return to a menuof nine thumbnail images.
Auto shutter mode(Timer)Press the Menu button and select "Auto Shutter". Press the OK buttonagain to take an image automatically after 10 seconds.
(Setting mode)Press the Menu button and select "Setting". Press the OK buttonto enter the menu.
again
P.11
6-1.Windows 98SE / 2000 / ME / XP
6-2.Pentium 233MHz or higher
6-3.128MB SDRAM
6-4.Video(VGA) Card with 2MB of RAM for minimum 16-bit(High Color)display.
6-5.CD-ROM
6-6.USB port
6-7.600MB of free hard disk space.
6.System requirements
Installation of driver
Since VistaPix is a Mass Storage Device you can access captured images just as
if it were a hard drive, therefore no software driver is needed (See Mass Storage
Mode ).If using VistaPix with an older version of Windows 98SE it may be
necessary to install the software Driver.
BA
VistaPix PC with USB port
Erasing PicturesPress the delete button while the thumbnail menu or full-screen image is displayed. Select "Erase one" and press OK Button to erase a single frame. Select "Erase all" and press OK button to erase all frames.
P.7
ResolutionExposure valueDate/TimeTV outTime stamp
Exposure valueDate/TimeTV outTime stamp
ResolutionSETUPSETUP
3.0M2.0M0.3M
3.0M2.0M0.3M
RESOLUTLONRESOLUTLON
0.00.0EVEV
0.60.6EVEV
2004 01 3124:00:012004 01 3124:00:01
Date/TimeDate/Time
Resolution AdjustmentSelect "Resolution" and press OK Button. Choose the desired resolution and press OK button to change the image resolution. Indicates 0.3MP, indicates 2.0MP, and indicates 3.0MP on the LCD screen.
Exposure ValueSelect "Exposure value" and press the OK button. This allows you to change the exposure setting suggested by the camera. Press the Up or Down button to select a value between -1.5 and 1.5 and press OK button to accept theexposure value. Negative exposure values tend to underexpose (darken) your object while positive values will overexpose (brighten) the object.
Setup the DateSelect "Date / Time" and press the OK button to set the internal clock. Edit the correct date (y/m/d) and time (h/m/s) by pressing the Up-down button.Press the OK button again to complete the setting.
P.10
5. How to use the binocular
Focusing the Binocular
Adjusting the eyepieces
The distance between your eyes is called interpupillary distance.The interpupillary distance is different from one person to another.It is important to adjust your interpupillary distance before using the VistaPix:- Hold VistaPix firmly in the normal viewing position.- Adjust the barrels by pushing together or pulling apart until you see a single circular image with both of your eyes.
To adjust the eye-relief for eyeglass wearers: Fold down the rubber eyecups and place them against your glasses to get the best viewing result.
A. Set the Diopter Knob on underside of VistaPix to its center point between - and + . B. Choose an object that is at least 15 meters (49 ft) away.C. Looking with just your left eye, rotate the Center Focus Knob(2) until the object you are viewing is in best focus.D. Looking with just your right eye, rotate the Diopter Knob(1) until the object you are viewing is in best focus.E. Viewing your object with both eyes, turn the Center Focus Knob to bring it in best focus.
ResolutionExposure valueDate/TimeTV outTime stamp
Resolution
Date/TimeTV outTime stamp
Exposure value
SETUPSETUP
ResolutionExposure valueDate/TimeTV outTime stamp
ResolutionExposure value
TV outTime stamp
Date/Time
SETUPSETUP
TV-out Display ModeSelect "TV out" and press OK button. Choose the corresponding output (NTSC for United States or PAL for Europe) and press OK button tocomplete setting.
NTSCPALNTSCPAL
TV OUTTV OUT
ResolutionExposure valueDate/TimeTV outTime stamp
ResolutionExposure valueDate/Time
Time stampTV out
SETUPSETUP
Auto power Auto power allows you to select the duration of time that your VistaPix can be inactive before it automatically power itself down. Select "Auto power OFF"from setting menu, press OK button. Select the indicated time of auto power inactivity shutdown. Press OK button again to complete the set-up.
ResetSelect "Reset" from setting menu, press OK button to make the selection.Select "Yes" to return the original factory setting. Select "No" to retain thecurrent settings. Press OK button to complete the set-up.
P.9
Play backAuto shutterSettingPower off
Play backAuto shutterSettingPower off
MEMUMEMU
P.8
Power Off modePress menu button and select "Power off". Press OK button. to poweroff.
Beep SoundSelect "Beep" from setting menu. Press OK button ,select ON to turn on thebeep sound.OFF to turn off the beep sound.Press OK button to completethe setting.
BeepAuto power OFFFormatReset
Auto power OFFFormatReset
BeepSETUPSETUP
ONOFFONOFF
Beep SoundBeep Sound
Time stamp on photoSelect "Time stamp" from setting menu,press OK button ,select ON todisplay time on photo.OFF to skip time on photo.Press OK button again to complete the setting.
ONOFFONOFF
Time stampTime stampResolutionExposure valueDate/TimeTV outTime stamp
ResolutionExposure valueDate/TimeTV outTime stamp
SETUPSETUP
90 seconds3minutes5minutes10minutes15minutes
90 seconds3minutes5minutes10minutes15minutes
Auto power OFFAuto power OFFBeepAuto power OFFFormatReset
Beep
FormatReset
Auto power OFF
SETUPSETUP
FormattingSelect "Format" and press OK button. When you choose "Yes" and press Shutter button ,a confirmation screen is displayed. Press OK buttonto start formatting the internal memory. Warning all stored image will be erased after formatting is complete.
YesNoYesNo
FORMATFORMAT
YesNoYesNo
ReformatDo not power off
ReformatDo not power offBeep
Auto power OFFFormatReset
BeepAuto power OFF
ResetFormat
SETUPSETUP
YesNoYesNo
Reset settingReset settingBeepAuto power OFFFormatReset
