+ All Categories

BIO-RAD

Date post: 03-Feb-2017
Category:
Upload: dangtuong
View: 212 times
Download: 0 times
Share this document with a friend
1
For True Microsampling Capability on Every FT-IR Introducing the first Microsampling Accessory for be continuously varied from 250 microns down to a your FT-IR. Now you can measure the infrared spectra minimum of 20 microns or diffraction limit. of samples as small as 20 microns in diameter. This A Microsampling Accessory is available for either accessory works with Digilab's QUALIMATIC™and FTS,*as well as most IBM, Nicolet and other FT-IR instruments. Before, if you wanted to measure very small sample areas, you had to use time-consuming pinhole masking. With Digilab's Micro- sampling Accessory, you can visibly locate the sample of interest under the high-powered micro- scope objective and, with the flip of a switch, obtain the infrared spectra in seconds. This visual alignment capability assures that you are measuring only the area of interest. Look to Digilab. 1 1 1 reflectance or transmittance studies, permitting analysis of virtually any material. Also avail- able is an X-Y stage with stepping motor drive for computer-controlled mapping of sample surface areas. Now you can do sophisticated microsampling faster and easier than ever before. For detailed information on how the new Microsampling Accessory can help your laboratory, look to Digilab, the long-time industry leader in FT-IR. To a d d a dedi- cated FT-IR microsampling capability, ask about Digilab's cost-effective configuration Data collect times are reduced due to matching MCT including the QUALIMATIC, Microsampling Accessory and optimized mating optics. The sampling size can and 4-color plotter. BIO-RAD Digilab Division 237 Putnam Avenue, Cambridge, MA 02139 Telephone: (800) 225-1248 Telex: 921481 Also in Australia. Austria, Canada, England, Germany, Holland, Italy. Japan, the Netherlands and Switzerland te. CIRCLE 12 ON READER SERVICE CARD
Transcript

For True Microsampling Capability on Every FT-IR

Introducing the first Microsampling Accessory for be continuously varied from 250 microns down to a your FT-IR. Now you can measure the infrared spectra minimum of 20 microns or diffraction limit.

of samples as small as 20 microns in diameter. This A Microsampling Accessory is available for either accessory works with Digilab's

QUALIMATIC™and FTS,*as well as most IBM, Nicolet and other FT-IR

instruments. Before, if you wanted to measure

very small sample areas, you had to use time-consuming pinhole masking. With Digilab's Micro­sampling Accessory, you can

visibly locate the sample of interest under the high-powered micro­

scope objective and, with the flip of a switch, obtain the infrared spectra in seconds. This visual

alignment capability assures that you are measuring only the area

of interest.

Look to Digilab.

111

reflectance or transmittance studies, permitting analysis of virtually any material. Also avail­able is an X-Y stage with stepping motor drive for computer-controlled mapping of sample surface areas. Now you can do sophisticated microsampling faster and easier than ever before.

For detailed information on how the new Microsampling Accessory can help your laboratory, look to Digilab, the long-time industry leader in FT-IR. To add a dedi­cated FT-IR microsampling capability, ask about Digilab's cost-effective configuration

Data collect times are reduced due to matching MCT including the QUALIMATIC, Microsampling Accessory and optimized mating optics. The sampling size can and 4-color plotter.

BIO-RAD Digilab Division

237 Putnam Avenue, Cambridge, MA 02139 Telephone: (800) 225-1248 Telex: 921481

Also in Australia. Austria, C a n a d a , England, Germany, Hol land, Italy. J a p a n , the

Netherlands a n d Switzerland te. CIRCLE 12 ON READER SERVICE CARD

Recommended