29
COMPANY PROFILE
COMPANY PROFILE
Summary
BIZMUTH is dedicated to offering a technical service of unparalleled calibre to the customer with the support of one of the most powerful forces in the engineering industry – BMG (previously known as Bearingman).
With a crew of qualified engineers offering their services at your business’s doorstep to find the best possible solution to your hydraulic or engineering problem, a call out service allows us to come to your place of business saving you time, money and hassles.Comprehensive lists of products on offer as well as availableengineering services are documented below. Combining these wellestablished and reliable products with a full comprehensive range of services, we believe that you need not look further for your Hydraulic and engineering needs.
BIZMUTH ENGINEERING
MISSION STATEMENT
Summary
- Call Centre- Off-Site Hydraulic Repair Service- Off-Site Hydraulic Testing Service- Project Engineering, System design and a Technical Consulting Service- On-site Mobile Workshop Service- Off-site fluid analysis service including: o Drawn Down Particle Isolation Procedure for an Impurity test o Karl Fischer Water-In-Oil Test (ASTM D4928 IP386) o Viscosity Test (ASTM D445/IP71) o Fluid Analysis Reports o Fluid Cleanliness Target Levels
SERVICES
Summary
- Accumulators - Larzep Hydraulics- Hydraulic Pumps- Reservoir Accessories- Valves- Heat Exchangers- Hydraulic Motors- Hydraulic Plumbing- Cylinders- Filtration- Bieri High Pressure Hydraulic components- Steel tubing
HYDRAULIC PRODUCTS
Summary
- Steel tubing (welded and seamless)
- Drill rods for exploration drilling
- Drill steels for mining
- Steel piping of any diameter + supply of steel
flanges
- Steel forgings of any size
- Steel and SG castings
- Manufacture of large components
- Structural steel (any grade and size)
- Grout bags for mines
- Specialised aluminium components
- Manufacture of large wheels, crusher drums, rope sheave wheels
- Bogey wheel sets with axles and bearing housings
- Shafts and crusher shafts
- Manufacture of sheave wheels, rope drums, etc
- rod mill bars
- Stainless alloy and duplex alloy bars and rods
- Carbon steel bars and rods
- Stainless, carbon steel and duplex alloy plate
- Steel sections
- Non-ferrous castings
- Valves
- Large pumps to requirement
ENGINEERING PRODUCTS
About us Welcome to BIZMUTH Engineering, specialising in hydraulic engineering in Southern Africa. With a focus on quality, BIZMUTH combines intimate knowledge and experience with state of the art technology and raw power, to deliver the most powerful and reliable hydraulic solutions money can buy. In today’s
challenging industrial environment it’s not enough to deliver pin-point Precision, Herculean strength and near immortal reliability. You must offer all of this at once and compliment it with instantaneous back up in the form of expert technical assistance, repair and maintenance facilities, and much more. These are our values, and this is what you can expect from a pioneer at the cutting edge of hydraulic engineering.
We are a brand new distributor for the newly owned BMG Hydraulics, once Goldquest International
Hydraulics previously VICKERS systems. Our company is primarily focused on offering technical expertise within the industrial field, particularly the mining field – through from, the removal of minerals to the
refinery of the respective minerals, with the support of BMG, BIZMUTH is in a situation to offer the client a range of tried and tested solutions to many problems encountered within the field. BIZMUTH is not only a specialist within the mining field, the expertise of the staff at BIZMUTH goes far beyond just mining and can offer solutions to any hydraulic engineering problem.
BIZMUTH became a licensed distributor for BMG Hydraulics in June 2009 and established a client base within the North Western Region of South Africa. The Company was founded by 3 mechanical Engineers namely Dustin Pereira, Jack Darier and Christopher Booysen. Below is a detailed history of BIZMUTH’s
supplier – BMG Hydraulics.
Late 1950’s - Company founded as West & Du Toit and became a Subsidiary of the Vickers Corporation.
1968 - Began trading under the Vickers Brand supplying Vickers branded products to all industries and
continued to do so for two decades.
1989 - The Goldquest Hydraulics brand was born when the company was acquired by a South African
concern who added corresponding product lines to the already renowned Vickers range. For the first time, the company could offer a comprehensive product range to meet every need of South African industry in the field of hydraulics and pneumatics. In addition, new value adding services were introduced to complete the circle and create a solution-orientated company.
Despite having a superior product range and a full spectrum of support services, competent distribution remained key in delivering solutions to the diverse customer base that existed. To fulfill this need, Goldquest Hydraulics went about appointing a network of accredited distributors. Each distributor was evaluated in terms of technical ability, service orientation and local market knowledge.
2008 - BMG Purchases Goldquest (Pty) Ltd.
2009 - Goldquest (Pty) Ltd. becomes BMG Hydraulics. This propels the company to new heights and
consolidates BMG Hydraulics as the market leader with the expertise and resources to
comprehensively service customers in all forms of South African industry.
With BMG Hydraulics as a supplier and a large range of products available to BIZMUTH there should be no doubt that any hydraulic needs can be solved by the proficient team of engineers at your service.
INTRODUCTION
COMPANY HISTORY
About us“Our affirmed vision is to be acknowledged throughout the North Western Region of South Africa as the first choice provider of hydraulic technical expertise, products, services and solutions”
In pursuing our vision, We are passionate about:
• SupplyingthewidestrangeofSuperiorQuality
• ProductsandServices
• ProvidingTechnicalServicebeyondourcustomers’expectations
• ProvidingonlyCompetentAdviceandExecution
• Innovatingintermsofnewproductdesigns,applicationsandservicedelivery
• Empoweringpeople
We will be the best by:
• Employingonlythebestpeople,productsandmaterials
• Continuouslymonitoringtheneedsofourcustomers
• Innovatingintermsofproductandservicedelivery
• KeepinguptodatewiththelatestformsofHydraulicengineeringandproductsavailableinthe market place.
BIZMUTH has a an office located in the Northcliff area within the North Western suburbs of Johannesburg. Our supplier BMG Hydraulics manufacturing and warehousing facilities are based in Benrose, at the heart of Johannesburg. The facilities in Benrose span 7 794m2 with workshops and machine centres covering over 2 200m2 of the site. The remainder consists of warehousing facilities and offices. With immediate access to both the N1 and N3 national highways, and close proximity to Johannesburg International Airport.
VISION AND MISSION
PREMISES
About us
We appreciate the importance that our valued customers place on quality, and assuring them that BIZMUTH takes every step to ensure that they receive only the highest quality products and services is of strategic importance to us. Each system is tested under the watchful eye of a senior engineer at BIZMUTH to ensure that the customer is receiving only a top notch product. BIZMUTH’s supplier – BMG Hydraulics has been audited and awarded ISO 9001: 2000 accreditation from an internationally recognised accrediting body, DQS, affording you the peace of mind that comes with knowing that any work carried out by BMG Hydraulics complies with the ISO’s strictest quality assurance standards.
BIZMUTH has four main members making up a specialised team that can offer a technical service like no other hydraulic distributor can. Each member is a BSC qualified Engineer in the Mechani-cal, Electrical and IT fields. The combined experience and knowledge of these individuals shall ensure that you receive the most precise engineering solutions. The company employs casual staff to assist on site situations.
BIZMUTH is fully BEE accredited to level 6.
BMG Hydraulics employs over 110 men and women from diverse backgrounds. In an industry such as ours, where skills and experience are scarce, the competencies developed and retained within our workforce give us a distinct advantage over our competitors. With a keen focus on people development, the full staff compliment, comprised of Qualified Engineers, Skilled Artisans, Technical Sales and Service personnel, Semi-Skilled workers and Clerical staff, are continually trained and coached to ensure that we not only maintain this position, but continue
to grow and learn both as individuals and as an organisation.
QUALITYMANAGEMENT
HUMAN RESOURCES
ServicesWhether in need of competent advice as to which component is best suited to your application, or alternatively, if you simply wish to place an order for any number of our quality products, our experienced Call Centre Consultants are at hand to assist you.
Regular training interventions ensure that the knowledge of our staff is relevant and up to date with the latest technologies available from our diverse range of products. We realise the importance of providing the right advice first time. If unable to assist immediately, our consultant will be sure to quickly follow up your enquiry if more intricate technical aspects require investigation. Call our call centre for immediate service, or alternately, email your enquiry for a swift written response.
Call Centre
Tel Enquiries:
082 347 6313
082 336 3812
072 332 3720
Email Enquiries: [email protected]
CALL CENTRE
We have the capacity to repair a full spectrum of products throughout the hydraulic field including; variable and fixed displacement pumps, industrial valves, mobile valves, Staffa low speed torque motors, high speed motors, accumulators and many more. All repairs are carried out by qualified and experienced artisans, and carry the same comprehensive warrantee as our high quality manufactured products.
The only way to avoid problems down the line with hydraulic components in any system where high pressures and stresses and close tolerances are in play on a constant basis, is to employ only genuine spare parts, ensuring the integrity of the system as a whole. In respect of this BIZMUTH repairs are undertaken using only the highest quality genuine spare parts.
Accurate diagnosis of component failure and appropriate repair is only achieved through years of experience. Consequentially each repair follows strict ISO accredited works procedures that are based on this hard-earned experience, ensuring that the component is returned to maximum efficiency. Furthermore, our artisans benefit from training by the original equipment manufactures, guaranteeing an absolute understanding and intimate knowledge of the product they are working with.
Every repaired product is assessed by our testing facility, affording you the peace of mind that comes with knowing that your equipment has passed BIZMUTH and BMG Hydraulics strictest
performance standards.
HYDRAULICS REPAIR CENTREServices
Services
BIZMUTH makes use of the BMG hydraulics test facility and expertise where the expert technicians confidently assess the state of your equipment in the test centre, which is on par with any hydraulic test facility in South Africa. The test facilities includes:
• 4variablespeeddrivetestbays,capableoftestingvane,piston,gearandotherpumps with power input requirements of up to 132kW
• FullDynamicTorqueTestingofhydraulicmotorsupto35kiloNMoftorqueonour dynamic load cell, a capability unparalleled in South Africa
• CompleteCETOPvalvetestingfacility
• Pressurecontroltesting
• FlowControlTesting
• Proportionalcontroltestingincludingintegralelectronics
• Manifoldblockandcartridgevalvetestfacility
• Cylindertestfacilitycapableoftestingawiderangeofsizesupto1000Barworking pressure
• Accumulatorshelltesting
Test certificates are issued on request for component tested, affording you the peace of mind that comes with knowing that your equipment has passed BIZMUTH and BMG
Hydraulics strictest performance standards.
HYDRAULIC TEST CENTRE
Services
BIZMUTH is focused on delivering turnkey
solutions and projects with skill and
knowledge that the engineers possess.
With one of the most accomplished
projects department within the hydraulic
field supporting the engineers at BIZMUTH.
The projects department at BMG Hydraulics
has assembled an impressive portfolio of
success stories over the years involving
some revolutionary projects.
The process begins with the scope of the project being accurately defined through
extensive on site consultation with the client. Thereafter, the appropriate solution is devised by drawing on the collective expertise of the engineering team. Each solution is unique, and developed to exacting specifications using our sophisticated CAD technology. 3D “Solid modelling” allows us to present a virtual image of the design in our drawing office prior to manufacture, keeping the client informed of our progress and the design that shall be implemented, and providing added piece of mind.
Many people still associate hydraulics with a cylinder going up and down, but there is a lot more to hydraulics in this day and age. Technology and techniques have moved past the simple pump and cylinder stage and we are now seeing systems, integrated through the use of smart technologies, which are stretching the boundaries of traditional hydraulic design. The Key to our success is the broad range of competencies manifested within the team.
BIZMUTH engineers, due to their vast experience and varied backgrounds, have the ability to integrate different technologies, from Hydraulics and Pneumatics, to Electronics and
Information Technology.
PROJECT ENGINEERING
AND CONSULTING
Services
We identify that unscheduled shutdowns as a result of system failure are a massive point of concern for any production- orientated business. Therefore the concept of the mobile service workshop was devised, to perform as a hydraulic- ambulance. Travelling to you at a moments notice to get your system up and running again in the shortest time possible. The mobile service workshop is fitted with all the tools, spares and equipment necessary to perform the following functions:
• Troubleshooting
• Technicalassistance
• On-siterepairs
• Installationsandcommissioning
• Systemflushing
• On-sitefluidanalysis(Drawdownparticleisolationandparticlecount)
• Hoseandpipeassembly
Fluid Analysis Service
An often over-looked, but critical element in any hydraulic or lubrication system is
contamination control. The benefits of a system maintained through the use of high quality filtration equipment coupled with a regular sampling and testing programme can be
measured in terms of increased performance and longevity of components. Ultimately these improvements reflect in lower maintenance costs.
BIZMUTH’s systemic approach to contamination control consists of three key steps that allow you to obtain and maintain the appropriate cleanliness level for your hydraulic or
lubrication system.
1. Determine the Target Cleanliness Level for the system
2. Take Action to achieve the Target Cleanliness Level
3. Monitor & Maintain Fluid Condition
Ascertaining the current state of your system fluid, as well as monitoring and maintaining fluid condition once corrective measures have been taken is made easy through BIZMUTH and BMG Hydraulics comprehensive Fluid Analysis Service.
The laboratory is fully equipped to perform an exhaustive range of test procedures,
specifically designed for the analysis of hydraulic and lubrication system fluid. The equipment in the lab is at the technological apex and is routinely calibrated to ensure that accuracy is verifiable.
MOBILE SERVICE
WORKSHOP
ServicesSolid particulate contaminants are arguably the most common cause of failure in hydraulic components. Ensuring that particulate contamination is not a factor in the failure (catastrophic, intermittent, or degradation) of any component in your system, is the first step in creating a risk management envelope for the system. This test determines the level of particulate contamination in your system fluid through the use of an automatic particle counter. The automatic particle counter uses a high intensity laser light source coupled with a photo sensor. This actively counts the number and size of particles contained in a fluid sample. The quantitative results of the count are reported in a detailed particle size distribution table, sorted by size and quantity.
This quantitative data is then translated to produce an ISO 4406 cleanliness code for the sample (e.g. 18/16/14). The cleanliness code for the sample can then be compared against the cleanliness level recommended for the system.
Services
A derivative of analytical ferrology, the drawdown particle isolation procedure is the most accurate form of particle identification. This test determines the insoluble contaminates in the fluid. Particles and gel-like matter both organic and inorganic that are present in the sample are captured on the surface of a 0.8 micrometer filter membrane and identified by the analyst using an optical microscope. Type and size of particles are recorded and the findings are then detailed in the report supplied to the customer. High resolution
photomicrographs of any contamination found in the sample (taken at 100X
magnification) are submitted along with the written report as a visual reference.
The water-in-oil analysis determines the amount of water present in the fluid sample.
Water inside a system will:
• Corrodemetalsurfacesandattackbearingsubstrates
• Causeinstabilityofchemicaladditivesinthelubricants
• Increaseoxidationandaccelerateacidformation
• Formemulsions
• Reducelubricity
Hence, ensuring that the amount of water in your hydraulic or lubricating fluid is within
acceptable limits is crucial in ensuring the performance and longevity of your system.
The test is conducted in accordance with ASTM D4928, a reagent is added to a measured amount of the sample fluid and the resultant reaction allows the test equipment to detect and report the presence of water in the sample in parts per million (ppm). The result can then be compared against the limits deemed acceptable for the fluid.
DRAWDOWN PARTICLE
ISOLATION PROCEDURE
KARL FISCHER WATER-IN-OIL
TEST (ASTM D4928IP386)
Services
The choice of hydraulic oil to be used requires careful consideration. Oils that are too thin may not provide effective lubrication, and oils that are too thick may give rise to excessive pressure.
Although a well designed new system will be equipped with fluid of the correct viscosity grade, changes in viscosity can and do occur for a number of reasons:
• Addingtop-upfluidthatisofthewrongviscositygradetothesystemcanalterthe viscosity of the fluid
• Oxidationcausesincreasesinviscosity
• Highsolidcontaminantlevelscancauseincreasesinviscosity
• Sheerdownofadditivescanresultinviscositydecreases
Viscosity is tested according to ASTM D445 using a heated viscometer and the results are reported in centistokes (cSt).
Two measures are reported with each test:
• Viscosityat40oC(Heated)
• Viscosityat100oC(Corrected)
The results of this test can be compared against the viscosity specified for new oil by the manufacturer. The lab is equipped to test viscosities from 20 to 810 cSt.
The scientific data captured during these tests generates the most useful reports possible on the condition of your system fluid. Although our scientific equipment and tests are highly advanced, your report is always easy to read and understand. By taking the mystery
out of fluid analysis we provide a service that clearly explains the benefits of clean systems.
VISCOSITY TEST (ASTM D445/IP71)
FLUID ANALYSIS REPORTS
Services
The fluid results target gives a quick overview of the condition of the sample submitted. The target measures the following five critical areas of fluid condition:
• 4μmicronparticlesofcontamination
• 6μmicronparticlesofcontamination
• 14μmicronparticlesofcontamination
• Watercontent
• Viscosity
When the marker is in the inner circle of the target, this represents “on-target” fluid condition. The second ring on the target represents marginal performance.
The third ring on the target indicates the need to resample the fluid because of the
possibility of a sampling error, and the last ring on the target indicates that immediate action is required as the fluid is severely contaminated. The Goldquest’s “Fluid Cleanliness Target” is a graphical way of understanding whether or not the fluid sample is meeting its target cleanliness level.
The results of each analysis performed in our laboratory are stored on a database. Trend information is then provided with each successive report which indicates:
• Thedegreeofimprovementifcorrectivemeasureshavebeentaken
• Alertsthecustomerofanysuddenspikesincontaminationlevels,providinganearlywarning if the cleanliness level of the system is found to be deteriorating
Trend data is supplied for the following key indicators:
• ParticleCount
• Water-in-oil
• Viscosity
FLUID CLEANLINESS TARGET
TREND ANALYSIS
Services
There are many oil analysis labs out there, and many proclaimed filtration specialists. But a report is useless without knowing how to correct any problem areas identified without adversely affecting the workings of the system. We believe only BIZMUTH has the ideal combination of expertise in contamination control, fluids and hydraulic engineering to provide you with the correct advice. Your report contains recommended steps from our engineers based on decades of experience in maintaining hydraulic systems. Customers enjoy added piece of mind, knowing that the information contained in the report is from one of the fluid power industry’s most credible sources. Whether you have a small operation with few hydraulic systems, or a large organisation with hefty maintenance expenditure, we have a fluid analysis package available to suit your consumption patterns. Ultra clean sampling kits are available from our call centre.
RECOMMENDATIONS
Services
A key to specialized hydraulic service is the addition of manufacturing hydraulic cylinders according to the application, very few Hydraulic companies will manufacture cylinders to your application, they would rather you change your application to suit the design of a
standard cylinder. BIZMUTH together with BMG Hydraulics follows the approach of
designing a system to the customer’s needs and will supply hydraulic cylinders according to the application of the client. BMG Hydraulics has built this reputation cylinder by cylinder for decades, creating hydraulic masterpieces upon which the industry is built. All cylinders are designed and produced from start to finish by BIZMUTH engineers and BMG Hydraulics ISO accredited Cylinder Design and Manufacture Department. Starting with computer
assisted design and advanced 3D modeling, and progressing right up to fabrication, where experienced and highly qualified artisans make use of the highest quality imported honed barrels and chromed bars.
Unlike the majority of South African manufacturers,
the engineered cylinders do not use peeled steel
bars that are finished, flash chromed and polished.
All our bars are ground and plated with micro cracked
chrome. The roundness, straightness and corrosion
resistance of these bars is infinitely superior to any
locally produced bars. BIZMUTH cylinder tubes are cold
drawn steel DIN ST 52 BK+S (stress relieved)
manufactured in accordance with
DIN 2391-C (seamless). The tubes are straight within 0,5 : 1000 mm with an I.D. tolerance of H8.
BIZMUTH has access to a full machining facility at BMG Hydraulics, the manufacturing
capabilities comes from the use of high-speed CNC lathes, which facilitates high speed,
repeatability and accuracy. As well as high-spec facilities, which enable us to produce
customized cylinders of any size.
CYLINDER DESIGN
AND MANUFACTURE
Services
BIZMUTH are also engaged in the refurbishment of cylinders, which are subsequently
tested by our test facility to ensure quality and reliability. The BMG Hydraulic cylinder
department boasts a staff compliment with decades of experience in cylinder repair and
design evaluation. Chronic cylinder problems are normally the result of inadequate initial
design and/or incorrect prior repair.
Our engineers will quickly identify the root cause of chronic cylinder leaks and other plant failures. If your plant or equipment requires regular overhaul, please contact one of our engineers for assistance. The types of cylinders that BIZMUTH can supply are listed below, but remember that this is a guide, BIZMUTH can custom build a cylinder according to a customer’s application.
• High-pressurecylinderswithoperatingpressuresupto70Mpa
• Multistagetelescopicrams,bothsingleanddoubleacting
• Constantvelocitytelescopicrams
• Heavydutymilltypecylinders
• Lowfriction-highspeedcylinders
• Bellevillespringactuatedhydraulicreleaseclampcylinders
BIZMUTH offers standard cylinders that have an extremely quick turnaround time; a full
catalogue is available listing all the series of standard cylinders. The range has been de-signed for use in industrial and mobile applications with operating pressures to 25 Mpa. Standard cylinders are useful when designing new systems, a large range of literature is available on the standard cylinders and many options are available for the specific design application.
CYLINDER REPAIR
AND TESTING
STANDARD CYLINDERS
Services
BIZMUTH offers design and manufacture
of hydraulic systems and manifolds with
the backup of BMG Hydraulics
experience of more than half a century.
Manifold design and manufacture
department at BMG Hydraulics is one
of the most technically advanced
facilities to be found in the continent.
Complete end-to-end service from
initial design to the finished product
all takes place in-house using Computer
Assisted Design and Manufacture (CAD & CAM).
Our sophisticated 3D “solid” modeling technique means that both interior and exterior dimensions of the manifold can be viewed in a virtual environment prior to fabrication. The advantage being that any potential flaws in the design can be identified and amended to the client’s specifications prior to manufacture.
Milling and machining takes place in the highly advanced CNC machining centres. In addition to the high quality finishes produced by this machinery, accuracy and repeatability in high volume runs is also ensured by the CAM process.
BIZMUTH’s manifolds are fabricated with quality assured Durabar steel plate imported from the USA, and because all fabrication takes place on BMG Hydraulics’ premises, complete control over quality is exercised through a ISO accredited works procedures. This degree of control over quality is to our knowledge unparalleled in Southern Africa.
MANIFOLD DESIGN
AND MANUFACTURE
Product Brands
Product Detailed List
Accumulators
• Accessories
• Accumulators
• Bladder
Cylinders
• ChromedBar
• ConstructionKit
• CylinderTubing
• GQ2Series
• RodEnds
Filtration
• Breathers
• HighCapacity
• HighPressure
• LowPressure
• MobileFiltration
• PressureIndicator
• Spin-onFilters
• Suction-LineFilters
• Tank-TopFilters
Product Detailed List
Heat Exchangers
• AirBlastCooler
• OilCoolers
Hydraulic Motors
• GearMotors
• PistonMotors
• VaneMotorSpares
Hydraulic Plumbing
• Adaptors
• AdjustableCouplings
• BlankingPlugs
• BulkheadCouplings
• EqualCouplings
• Flanges
• GaugeAdapter
• LineTubing
• NutsandCuttingRings
• PortFlanges
• QuickCouplers
• SAEFlanges
• SteelTubeFitting
• StudCouplings
• TestPoints
• TubeClamps
• Weld-onCoupling
Product Detailed List
Larzep Hydraulics
• Accessories
• Cable-Cutter
• ChainCutters
• DoubleActingCylinder
• FlowandPressureValves
• HighTonnage
• NutSplitters
• PullCylinders
• PumpsandPowerUnits
• SingleActHighTon
• SingleActSpringReturn
• SingleandDoubleActing
• SpreadCylinder
• Telescopic
Reservoir Accessories
• HousingandCouplings
• LevelGauges
• PressureGauges
• Reservoirs
Product Detailed List
Pumps
• GearPumpSpares
• GearPumps
• HandPumps
• Hydrokraft
• MultipleGearPumps
• PistonPumpSelection
• PistonPumpSpares
• PistonPumps
• UltraHighPressure
• VanePumpSpares
• VanePumps
• VanePumps2
Product Detailed List
Valves
• BallValves
• CheckValve
• DirectionalControl
• DirectionalSpares
• FlowControlValve
• MobileCheckValves
• MobileDirectionalValve
• MobileFlowControl
• MobileFlowDiverter
• MobileLoadControl
• MobilePressureControl
• PrefillValves
• PressureSwitches
• Skrew-inCartridge
• SpoolChart
• SystemStackValves
• UltraHighPressure
Product Detailed List
Engineering Products
- Steel tubing (welded and seamless)
- Drill rods for exploration drilling
- Drill steels for mining
- Steel piping of any diameter + supply of steel
flanges
- Steel forgings of any size
- Steel and SG castings
- Manufacture of large components
- Structural steel (any grade and size)
- Grout bags for mines
- Specialised aluminium components
- Manufacture of large wheels, crusher drums, rope sheave wheels
- Bogey wheel sets with axles and bearing housings
- Shafts and crusher shafts
- Manufacture of sheave wheels, rope drums, etc
- rod mill bars
- Stainless alloy and duplex alloy bars and rods
- Carbon steel bars and rods
- Stainless, carbon steel and duplex alloy plate
- Steel sections
- Non-ferrous castings
- Valves
- Large pumps to requirement
Product Detailed List
PleaseFeelFreetocontactusforfurtherinformation:
Tel:
DustinPereira 0823476313Jack Darier 082 336 3812Christor Booysen 072 332 3720
Email:
