List of flash codes Combi (E) Combi 4/15 V05.00.00)
# Flashcode Note Error Error information 1st action 2nd action 3rd action
4 ssss,slss Current for combustion air motor too
high
Combustion air motor or cable harness
defective
Check / replace combustion air
motor
Check / replace cable harness
5 ssss,slsl Current for combustion air motor too
low
Combustion air motor or cable harness
defective
Check / replace combustion air
motor
Check / replace cable harness
6 ssss,slls Current for combustion air motor too
high
Combustion air motor or cable harness
defective
Check / replace combustion air
motor
Check / replace cable harness
8 ssss,lsss Electronic fault Failure in electronic PCB Restart heater
10 ssss,lsls Plausibility of combustion air
temperature sensor
The speed of the combustion air motor is
too low or outside the tolerance
Check cable of combustion air
temperature sensor
Check (read) / replace
combustion air temperature
sensor
11 ssss,lsll Electronic fault Failure in electronic PCB Restart heater Check power supply
15 ssss,llll Electronic fault Failure in electronic PCB Restart heater Check power supply
16 sssl,ssss Electronic fault Failure in electronic PCB Restart heater Check power supply
17 Summer mode with empty water
container
Summer mode with empty water
container
18 Warm air outlets blocked
Circulated air intake blocked
Check the individual outlet
apertures
Remove the circulated air intake
blockage
19 sssl,ssll Plausibility of electronic Electronics does not match the heater
(e.g. 6 kW PCB in 4 kW heater)
Install correct electronics
Page 1/232/16/17 English
List of flash codes Combi (E) Combi 4/15 V05.00.00)
# Flashcode Note Error Error information 1st action 2nd action 3rd action
20 sssl,slss NTC water temperature plausibility Water temperature sensor outside tolerance
range
Check cable of water
temperature sensor
Check (read) / replace water
temperature sensor
20 °C 12.6 kOhm
25 °C 10.0 kOhm
40 °C 5.0 kOhm
50 °C 3.3 kOhm
21 sssl,slsl NTC room temperature plausibility Room temperature sensor outside tolerance
range
Check cable of room
temperature sensor
Check (read) / replace room
temperature sensor
15 °C 16.2 kOhm
20 °C 12.6 kOhm
25 °C 10.0 kOhm
22 sssl,slls NTC air temperature plausibility Air temperature sensor out of tolerance Check cable of air temperature
sensor
Check (read) / replace air
temperature sensor
20 °C 124.9 kOhm
25 °C 100.0 kOhm
50 °C 36.0 kOhm
Check the thermostat
plate / air temperature
switch / air temperature
sensor for damage
caused by overheating
=> Inform the customer
service
23 sssl,slll Electronic fault Failure in electronic PCB Restart heater Check power supply
24 sssl,lsss Circulating air motor current too high Circulating air motor defective Check (apply 12 V) / replace
circulating air motor
25 sssl,lssl Circulating air motor current too low Circulating air motor or connection plug
failure
Check / replace circulating air
motor
Page 2/232/16/17 English
List of flash codes Combi (E) Combi 4/15 V05.00.00)
# Flashcode Note Error Error information 1st action 2nd action 3rd action
26 sssl,lsls Circulating air motor current too high Circulating air motor defective Check (apply 12 V) / replace
circulating air motor
If the SW index is lower than
V03.00.04, replace the
electronics
28 sssl,llss Current for control panel too high Control panel or control panel cable
defective
Check / replace control panel
cable
Replace control panel
29 sssl,llsl Current for FrostControl heating
element too high
Heating element or cable defective Check / replace heating element
30 sssl,llls Current for solenoid valve 2 KW
retaining coil too high
Solenoid coil or cable harness defective Check / replace solenoid coil Check / replace cable harness
31 sssl,llll Solenoid valve 4 KW attracting coil
current too high
Solenoid coil or cable harness defective Check / replace solenoid coil Check / replace cable harness
32 ssls,ssss Electronic fault Failure in electronic PCB Restart heater Check power supply
33 ssls,sssl Current for solenoid valve 2 KW
restraining coil too high
Solenoid coil or cable harness defective Check / replace solenoid coil Check / replace cable harness
34 ssls,ssls Solenoid valve 4 KW restraining coil
current too high
Solenoid coil or cable harness defective Check / replace solenoid coil Check / replace cable harness
35 ssls,ssll Electronic fault Failure in electronic PCB Restart heater Check power supply
36 ssls,slss Current for ignitor too high Ignitor or cable harness defective Replace ignitor Check / replace cable harness
37 ssls,slsl Electronic fault Failure in electronic PCB Restart heater Check power supply
38 ssls,slls Electronic fault Failure in electronic PCB Restart heater Check power supply
39 ssls,slll Electronic fault Failure in electronic PCB Restart heater Check power supply
Page 3/232/16/17 English
List of flash codes Combi (E) Combi 4/15 V05.00.00)
# Flashcode Note Error Error information 1st action 2nd action 3rd action
40 ssls,lsss Electronic fault Failure in electronic PCB Restart heater Check power supply
41 ssls,lssl Electronic blocked Electronic blocked:
- Because the air temperature switch and /
or water temperature switch opened during
operation due to over-heating
- Because the air temperature switch cable
is damaged
- Due to a short-circuit of the combustion air
temperature sensor (corresponds to
temperatures > 215 °C)
- Check the heater for
overheating damage
(heat exchanger, water storage
tank, in case of frost damage
also check the FrostControl, ..)
- Check the thermostat plate / air
temperature switch / cable / air
temperature sensor for
overheating damage
- Replace water temperature
switch , air temperature switch if
necessary
- Unlock the electronics
with the Truma
Diagnose Tool ("Lock"
symbol bottom right)
- Replace electronics
42 ssls,lsls Window switch open - Window switch detects open window
- Bridge for window switch on Truma
electronics interrupted
- Close window
- Check / replace window switch
with cable
Check secure fit / contact of
bridge on electronics
43 ssls,lsll Over voltage higher than 15 V 12 V power supply failure Recondition power supply 12 V
44 ssls,llss Undervoltage lower than 10.5 V 12 V power supply failure Recondition power supply 12 V
45 ssls,llsl No 230 V supply to Combi E 230 V power supply failure Check 230 V voltage
USA Addition:
Only Truma Combi eco plus or
Truma Combi comfort
No 120VAC supply voltage or
Overheating protection has
responded
Water temperature switch reset /
check 230 V
Page 4/232/16/17 English
List of flash codes Combi (E) Combi 4/15 V05.00.00)
# Flashcode Note Error Error information 1st action 2nd action 3rd action
46 ssls,llls 1) Control panel Combi or power
selector switch Combi E defective
2) Combustion air motor or
circulating air motor defective
3) Battery earth to the minus
terminal Combi defective
1) Control panel or control panel cable
defective
- Power selector switch Combi E or control
panel connection cable defective
2) Combustion air motor defective
- Cable harness defective
- Electronics defective (paint spray in control
panel socket)
- Internal connection between the (+) carbon
brushes and/or circulating air motor and
circulating air motor casing via carbon dust
3) Earth connection from the power supply
is missing
1) Replace Combi control panel /
or cable
- Replace power selector switch
Combi E and or control unit
connecting cable
2) Replace circulating air motor
3) Check earth connection
(ground cable) of power supply
- Check supply line of
combustion air motor - black
cable for short-circuit to ground
or red cable for interruption
- Replace cable harness
- (If cable harness not damaged,
replace combustion air motor)
Check electronics for
paint spray in control
panel socket (replace
electronic PCB)
47 ssls,llll Electronic fault Failure in electronic PCB Restart heater Check power supply
48 ssll,ssss Water temperature switch
over-temperature or air temperature
switch over-temperature
Fault:
- Because the air temperature switch and /
or water temperature switch opened during
operation due to over-heating
- Check the heater for
over-heating damage
- Check the thermostat plate /air
temperature switch / air
temperature sensor for damage
caused by overheating
=> Inform the customer service
- Check / replace the water
temperature switch and water
temperature sensor
- Check / replace the air
temperature switch / sensor and
cable
- Check / replace the circulating
air motor
49 ssll,sssl Electronic fault Failure in electronic PCB Restart heater Check power supply
50 ssll,ssls Electronic fault Failure in electronic PCB Restart heater Check power supply
51 ssll,ssll Electronic fault Failure in electronic PCB Restart heater Check power supply
Page 5/232/16/17 English
List of flash codes Combi (E) Combi 4/15 V05.00.00)
# Flashcode Note Error Error information 1st action 2nd action 3rd action
52 ssll,slss Electronic fault Failure in electronic PCB Restart heater Check power supply
53 ssll,slsl Electronic fault Failure in electronic PCB Restart heater Check power supply
54 ssll,slls Electronic fault Failure in electronic PCB Restart heater Check power supply
55 ssll,slll Electronic fault Failure in electronic PCB Restart heater Check power supply
56 ssll,lsss Electronic fault Failure in electronic PCB Restart heater Check power supply
57 ssll,lssl Electronic fault Failure in electronic PCB Restart heater Check power supply
58 ssll,lsls Electronic fault Failure in electronic PCB Restart heater Check power supply
59 ssll,lsll Electronic fault Failure in electronic PCB Restart heater Check power supply
60 ssll,llss Voltage fluctuation Power supply not constant Recondition power supply 12 V
61 ssll,llsl Failure due to ignition procedure Ignition spark disturbs the electronics Ignitor must have orange label,
otherwise replace ignitor
Replace the ignitor with a new
ignitor with index 05
62 ssll,llls Electronic fault Failure in electronic PCB Restart heater Check power supply
63 ssll,llll Electronic fault Failure in electronic PCB Restart heater Check power supply
64 slss,ssss Electronic fault Failure in electronic PCB Restart heater Check power supply
65 slss,sssl Electronic fault Failure in electronic PCB Restart heater Check power supply
66 slss,ssls Electronic fault Failure in electronic PCB Restart heater Check power supply
67 slss,ssll Electronic fault Failure in electronic PCB Restart heater Check power supply
Page 6/232/16/17 English
List of flash codes Combi (E) Combi 4/15 V05.00.00)
# Flashcode Note Error Error information 1st action 2nd action 3rd action
68 slss,slss Failure due to ignition procedure Ignition spark disturbs the electronics Ignitor must have orange label,
otherwise replace ignitor
Replace the ignitor with a new
ignitor with index 05
69 slss,slsl Current monitoring for circulating air
motor - with CP Plus: Software error
Circulating air motor defective - CP Plus
software earlier than C01.04.01 -
Electronics defective
Check the CP Plus software
version / software update
Replace the circulating air motor Replace the electronics
70 slss,slls Electronic fault Failure in electronic PCB Restart heater Check power supply
71 slss,slll Electronic fault Failure in electronic PCB Restart heater Check power supply
72 slss,lsss Electronic fault Failure in electronic PCB Restart heater Check power supply
73 slss,lssl Electronic fault Failure in electronic PCB Restart heater Check power supply
74 slss,lsls Electronic fault Failure in electronic PCB Restart heater Check power supply
75 slss,lsll Electronic fault Failure in electronic PCB Restart heater Check power supply
76 slss,llss Electronic fault Failure in electronic PCB Restart heater Check power supply
77 slss,llsl Electronic fault Failure in electronic PCB Restart heater Check power supply
78 slss,llls Electronic fault Failure in electronic PCB Restart heater Check power supply
79 slss,llll Electronic fault Failure in electronic PCB Restart heater Check power supply
80 slsl,ssss Voltage fluctuation / failure due to
ignition procedure
- Power supply not constant
- Ignition spark interfering with electronics
- The electrode cable and the combustion
air motor cable may not cross
- Apply clean 12 V power supply
- Install earth cable, part no.:
34020-57000 (see also service
info CB_110925)
- Ignitor must have orange label,
otherwise replace ignitor
Replace the electronics if the
error occurs again
Page 7/232/16/17 English
List of flash codes Combi (E) Combi 4/15 V05.00.00)
# Flashcode Note Error Error information 1st action 2nd action 3rd action
81 slsl,sssl Failure due to ignition procedure Ignition spark disturbs the electronics Check the earth connection of
the power supply
- Check the installation of the
solenoid valve
USA Addition:
Switch off warm-air heater and
allow to cool; if necessary,
fill the boiler with cold water.
Switch warm-air heater on again.
Replace the ignitor with a new
ignitor with index 05
Check / replace the
spark plug / flame
rectification electrode
lead
Check / set the gap
between the spark
plugs
Replace the electronics
82 slsl,ssls Electronic fault Failure in electronic PCB Restart heater Check power supply
83 slsl,ssll Electronic fault Failure in electronic PCB Restart heater Check power supply
84 slsl,slss Electronic fault Failure in electronic PCB Restart heater Check power supply
85 slsl,slsl Electronic fault Failure in electronic PCB Restart heater Check power supply
86 slsl,slls Electronic fault Failure in electronic PCB Restart heater Check power supply
87 slsl,slll Electronic fault Failure in electronic PCB Restart heater Check power supply
88 slsl,lsss Failure due to ignition procedure Ignition spark disturbs the electronics Ignitor must have orange label,
otherwise replace ignitor
Replace the ignitor with a new
ignitor with index 05
89 slsl,lssl Current monitoring for the
combustion air motor - with CP Plus:
Software error
Combustion air motor defective - CP Plus
software earlier than C01.04.01 -
Electronics defective
CP Plus software update Replace the combustion air
motor
Replace the electronics
Page 8/232/16/17 English
List of flash codes Combi (E) Combi 4/15 V05.00.00)
# Flashcode Note Error Error information 1st action 2nd action 3rd action
90 slsl,lsls Electronic fault Failure in electronic PCB Restart heater Check power supply
91 slsl,lsll Electronic fault Failure in electronic PCB Restart heater Check power supply
92 slsl,llss Electronic fault Failure in electronic PCB Restart heater Check power supply
93 slsl,llsl Electronic fault Failure in electronic PCB Restart heater Check power supply
94 slsl,llls Speed of the combustion air motor
incorrect
Heater becomes too hot or incorrect value
for the combustion air temperature sensor
Check / replace combustion air
temperature sensor and cable
harness
Check heater for damage due to
overheating
Check the exhaust pipe
does not leak
Check the gas supply
Check / replace the
circulating air motor
96 slls,ssss Electronic fault Failure in electronic PCB Restart heater Check power supply
97 slls,sssl Electronic fault Failure in electronic PCB Restart heater Check power supply
98 slls,ssls Electronic fault Failure in electronic PCB Restart heater Check power supply
99 slls,ssll Electronic fault Failure in electronic PCB Restart heater Check power supply
100 slls,slss - Cable harness fault
- Magnetic coils short circuit
Short-circuit on solenoid coils - Restart heater
- Check solenoid coils for
short-circuit / replace
Check / replace cable
harness
101 slls,slsl - Cable harness fault
- Igniter short circuit
Short-circuit on the ignitor - Restart heater
- Check igniter for short-circuit /
replace
Check / replace cable
harness
102 slls,slls Electronic fault Failure in electronic PCB Restart heater Check power supply
103 slls,slll Electronic fault Failure in electronic PCB Restart heater Check power supply
Page 9/232/16/17 English
List of flash codes Combi (E) Combi 4/15 V05.00.00)
# Flashcode Note Error Error information 1st action 2nd action 3rd action
104 slls,lsss Electronic fault Failure in electronic PCB Restart heater Check power supply
105 slls,lssl Electronic fault Failure in electronic PCB
106 slls,lsls Electronic fault Failure in electronic PCB Restart heater Check power supply
107 slls,lsll Electronic fault Failure in electronic PCB Restart heater Check power supply
108 slls,llss Electronic fault Failure in electronic PCB Restart heater Check power supply
109 slls,llsl Electronic fault Failure in electronic PCB Restart heater Check power supply
110 slls,llls Electronic fault Failure in electronic PCB Restart heater Check power supply
111 slls,llll Electronic fault Failure in electronic PCB Restart heater Check power supply
Page 10/232/16/17 English
List of flash codes Combi (E) Combi 4/15 V05.00.00)
# Flashcode Note Error Error information 1st action 2nd action 3rd action
112 slll,ssss Flame not detected 2) Bad earth or
battery earth for Combi minus
connection defective
USA Addition:
Gas pressure regulation system
defective
Electronics defective
1) Flame has gone out or is not detected
(error can also occur only after 3 - 5
minutes)
2) Earth connection of the power supply is
poor or missing
- Solenoid valve for nozzle tube askew
USA Addition:
Gas cylinder closed
Switch for gas shut-off valve open
Overheating protection has responded
Check gas supply Check the earth connection of
the power supply
- Check the installation of the
solenoid valve
USA Addition:
Switch off warm-air heater and
allow to cool; if necessary,
fill the boiler with cold water.
Switch warm-air heater on again.
- Check exhaust gas
system
- Replace the ignitor
plug kit
- Replace the solenoid
valve
- Replace the
electronics
USA Addition:
Switch off warm-air
heater and allow to
cool;
if necessary, fill the
boiler with cold water.
Check warm air outlets
and circulated air intake
and remove blockages.
Switch warm-air heater
on again.
113 slll,sssl Flame not expected Ionization voltage present in standby mode Check solenoid valve
(stuck in open position)
114 slll,ssls Electronic fault Failure in electronic PCB Restart heater Check power supply
115 slll,ssll Electronic fault Failure in electronic PCB Restart heater Check power supply
116 slll,slss Dirty supply voltage AC components in power supply Check power supply, AC
components also possible
through power supply units or
solar systems
Only operate heater with battery
Page 11/232/16/17 English
List of flash codes Combi (E) Combi 4/15 V05.00.00)
# Flashcode Note Error Error information 1st action 2nd action 3rd action
117 slll,slsl Dirty supply voltage AC components in power supply Check power supply, AC
components also possible
through power supply units or
solar systems
Only operate heater with battery
118 slll,slls Speed of the combustion air motor
too low
The speed of the combustion air motor is
too low or outside the tolerance
If the SW index is lower than
V03.00.04, replace the
electronics
Replace the combustion air
motor
119 slll,slll RPM of combustion engine too high - Combustion air motor running too fast or
outside tolerance range
- Ignition spark interfering with electronics
Ignitor must have orange label,
otherwise replace ignitor
Replace the ignitor with a new
ignitor with index 05
Replace combustion air
motor and / or
electronics
120 slll,lsss Electronic fault Failure in electronic PCB Restart heater Check power supply
121 slll,lssl Flame unstable Flame unstable during operation
USA Addition:
Gas cylinder closed
Switch for gas shut-off valve open
Overheating protection has responded
Check gas supply
USA Addition:
Gas cylinder closed
Switch for gas shut-off valve
open
Overheating protection has
responded
Check flue system
USA Addition:
Switch off warm-air heater and
allow to cool; if necessary, fill the
boiler with cold water. Switch
warm-air heater on again.
- Change ignition plugs
- Change electronics
USA Addition:
Check warm air outlets
and circulated air intake
and remove blockages.
Switch warm-air heater
on again.
Page 12/232/16/17 English
List of flash codes Combi (E) Combi 4/15 V05.00.00)
# Flashcode Note Error Error information 1st action 2nd action 3rd action
122 slll,lsls 1) Flame not detected
2) Electronics defective
- Gas supply interrupted
- Error in the electronics
USA Addition:
Combustion air infeed or exhaust gas outlet
closed
Gas pressure regulation system defective
Overheating protection has responded
Electronics defective
Check / replace the gas pressure
regulation system
USA Addition:
Check for obsbsstructions such
as slush, ice or leaves and
remove from openings.
- Restart the heater
- Check the power supply
USA Addition:
Check/ replace gas pressure
regulation system
Check the exhaust gas
system
- Replace the spark
plug set
- Replace the solenoid
valve
- Replace the
electronics
123 slll,lsll Electronic fault Failure in electronic PCB Restart heater Check power supply
124 slll,llss Electronic fault Failure in electronic PCB Restart heater Check power supply
125 slll,llsl Electronic fault Failure in electronic PCB Restart heater Check power supply
126 slll,llls Electronic fault Failure in electronic PCB Restart heater Check power supply
127 slll,llll Electronic defective or combustion
air motor running at incorrect speed
- Failure in electronic PCB
- Combustion air motor defective
- Cable harness defective
Check / replace cable harness Replace the combustion air
motor
128 lsss,ssss Electronic fault Failure in electronic PCB Restart heater Check power supply
129 lsss,sssl Electronic fault Failure in electronic PCB Restart heater Check power supply
130 lsss,ssls Electronic fault Failure in electronic PCB Restart heater Check power supply
131 lsss,ssll Electronic fault Failure in electronic PCB Restart heater Check power supply
133 lsss,slsl Electronic fault Failure in electronic PCB Restart heater Check power supply
134 lsss,slls Electronic fault Failure in electronic PCB Restart heater Check power supply
Page 13/232/16/17 English
List of flash codes Combi (E) Combi 4/15 V05.00.00)
# Flashcode Note Error Error information 1st action 2nd action 3rd action
135 lsss,slll Electronic fault Failure in electronic PCB Restart heater Check power supply
136 lsss,lsss Electronic fault Failure in electronic PCB Restart heater Check power supply
137 lsss,lssl Electronic fault Failure in electronic PCB Restart heater Check power supply
138 lsss,lsls Electronic fault Failure in electronic PCB Restart heater Check power supply
139 lsss,lsll Electronic fault Failure in electronic PCB Restart heater Check power supply
140 lsss,llss Electronic fault Failure in electronic PCB Restart heater Check power supply
141 lsss,llsl Electronic fault Failure in electronic PCB Restart heater Check power supply
142 lsss,llls Electronic fault Failure in electronic PCB Restart heater Check power supply
143 lsss,llll Electronic fault Failure in electronic PCB Restart heater Check power supply
144 lssl,ssss Electronic fault Failure in electronic PCB Restart heater Check power supply
145 lssl,sssl Electronic fault Failure in electronic PCB Restart heater Check power supply
146 lssl,ssls Electronic fault Failure in electronic PCB Restart heater Check power supply
147 lssl,ssll Electronic fault Failure in electronic PCB Restart heater Check power supply
148 lssl,slss Overtemperature of the combustion
air temperature sensor
Electronics locked:
- Because the combustion air temperature
sensor became too hot as a result of
overheating during operation
- Short circuit of the combustion air
temperature sensor
- Check the heater for
overheating damage
(heat exchanger, water storage
tank, in case of frost damage
also check the FrostControl, ..)
Check the exhaust pipe does not
leak
- Check / replace the combustion
air temperature sensor and cable
harness
- Replace the circulating air
motor
- Unlock the electronics
with the Truma
Diagnose Tool ("Lock"
symbol bottom right)
- Replace electronics
Page 14/232/16/17 English
List of flash codes Combi (E) Combi 4/15 V05.00.00)
# Flashcode Note Error Error information 1st action 2nd action 3rd action
149 lssl,slsl Water temperature switch
over-temperature or air temperature
switch over-temperature
Fault:
- Because the air temperature switch and /
or water temperature switch opened during
operation due to over-heating
- Check the heater for
over-heating damage
- Check the thermostat plate /air
temperature switch / air
temperature sensor for damage
caused by overheating
=> Inform the customer service
- Check / replace the water
temperature switch and water
temperature sensor
- Check / replace the air
temperature switch / sensor and
cable
- Check / replace the circulating
air motor
150 lssl,slls Air temperature switch
over-temperature or water
temperature switch
over-temperature
Fault:
- Because the air temperature switch and /
or water temperature switch opened during
operation due to over-heating
- Check the heater for
over-heating damage
- Check the thermostat plate /air
temperature switch / air
temperature sensor for damage
caused by overheating
=> Inform the customer service
- Check / replace the water
temperature switch and water
temperature sensor
- Check / replace the air
temperature switch / sensor and
cable
- Check / replace the circulating
air motor
160 lsls,ssss Electronic fault Failure in electronic PCB Restart heater Check power supply
161 lsls,sssl Electronic fault Failure in electronic PCB Restart heater Check power supply
162 lsls,ssls Electronic fault Failure in electronic PCB Restart heater Check power supply
163 lsls,ssll Electronic fault Failure in electronic PCB Restart heater Check power supply
164 lsls,slss Electronic fault Failure in electronic PCB Restart heater Check power supply
165 lsls,slsl Electronic fault Failure in electronic PCB Restart heater Check power supply
166 lsls,slls Electronic fault Failure in electronic PCB Restart heater Check power supply
167 lsls,slll Electronic fault Failure in electronic PCB Restart heater Check power supply
Page 15/232/16/17 English
List of flash codes Combi (E) Combi 4/15 V05.00.00)
# Flashcode Note Error Error information 1st action 2nd action 3rd action
168 lsls,lsss Electronic fault Failure in electronic PCB Restart heater Check power supply
169 lsls,lssl Electronic fault Failure in electronic PCB Restart heater Check power supply
170 lsls,lsls Voltage fluctuation / failure due to
ignition procedure
- Power supply not constant
- Ignition spark interfering with electronics
- The electrode cable and the combustion
air motor cable may not cross
- Apply clean 12 V power supply
- Install earth cable, part no.:
34020-57000 (see also service
info CB_110925)
- Ignitor must have orange label,
otherwise replace ignitor
Replace the electronics if the
error occurs again
171 lsls,lsll Failure due to ignition procedure Ignition spark disturbs the electronics Ignitor must have orange label,
otherwise replace ignitor
Replace the ignitor with a new
ignitor with index 05
172 lsls,llss Electronic fault Failure in electronic PCB Restart heater Check power supply
173 lsls,llsl Electronic fault Failure in electronic PCB Restart heater Check power supply
174 lsls,llls Electronic fault Failure in electronic PCB Restart heater Check power supply
175 lsls,llll Electronic fault Failure in electronic PCB Restart heater Check power supply
176 lsll,ssss Electronic fault Failure in electronic PCB Restart heater Check power supply
177 lsll,sssl Electronic fault Failure in electronic PCB Restart heater Check power supply
Page 16/232/16/17 English
List of flash codes Combi (E) Combi 4/15 V05.00.00)
# Flashcode Note Error Error information 1st action 2nd action 3rd action
178 lsll,ssls Failure due to ignition procedure Ignition spark disturbs the electronics Check the earth connection of
the power supply
- Check the installation of the
solenoid valve
USA Addition:
Switch off warm-air heater and
allow to cool; if necessary,
fill the boiler with cold water.
Switch warm-air heater on again.
Replace the ignitor with a new
ignitor with index 05
Check / replace the
spark plug / flame
rectification electrode
lead
Check / set the gap
between the spark
plugs
Replace the electronics
180 lsll,slss Electronic fault Failure in electronic PCB Restart heater Check power supply
181 lsll,slsl Electronic fault Failure in electronic PCB Restart heater Check power supply
182 lsll,slls Electronic fault Failure in electronic PCB Restart heater Check power supply
183 lsll,slll Electronic fault Failure in electronic PCB Restart heater Check power supply
184 lsll,lsss Speed of the combustion air motor
incorrect
Heater becomes too hot or incorrect value
for the combustion air temperature sensor
Check / replace combustion air
temperature sensor and cable
harness
Check heater for damage due to
overheating
Check the exhaust pipe
does not leak
Check the gas supply
Check / replace the
circulating air motor
186 lsll,lsls Electronic fault Failure in electronic PCB Restart heater Check power supply
187 lsll,slls Electronic fault Failure in electronic PCB Restart heater Check power supply
188 lsll,llss Electronic fault Failure in electronic PCB Restart heater Check power supply
Page 17/232/16/17 English
List of flash codes Combi (E) Combi 4/15 V05.00.00)
# Flashcode Note Error Error information 1st action 2nd action 3rd action
189 lsll,llsl Electronic fault Failure in electronic PCB Restart heater Check power supply
190 lsll,llls Electronic fault Failure in electronic PCB Restart heater Check power supply
191 lsll,llll Electronic fault Failure in electronic PCB Restart heater Check power supply
192 llss,ssss Electronic fault Failure in electronic PCB Restart heater Check power supply
193 llss,sssl Electronic fault Failure in electronic PCB Restart heater Check power supply
194 llss,ssls Electronic fault Failure in electronic PCB Restart heater Check power supply
195 llss,ssll Electronic fault Failure in electronic PCB Restart heater Check power supply
196 llss,slss Electronic fault Failure in electronic PCB Restart heater Check power supply
197 llss,slsl Electronic fault Failure in electronic PCB Restart heater Check power supply
198 llss,slls Electronic fault Failure in electronic PCB Restart heater Check power supply
199 llss,slll Electronic fault Failure in electronic PCB Restart heater Check power supply
200 llss,lsss Electronic fault Failure in electronic PCB Restart heater Check power supply
201 llss,lssl Electronic fault Failure in electronic PCB Restart heater Check power supply
Page 18/232/16/17 English
List of flash codes Combi (E) Combi 4/15 V05.00.00)
# Flashcode Note Error Error information 1st action 2nd action 3rd action
202 llss,lsls Flame not detected 2) Bad earth or
battery earth for Combi minus
connection defective
USA Addition:
Gas pressure regulation system
defective
Electronics defective
1) Flame has gone out or is not detected
(error can also occur only after 3 - 5
minutes)
2) Earth connection of the power supply is
poor or missing
- Solenoid valve for nozzle tube askew
USA Addition:
Gas cylinder closed
Switch for gas shut-off valve open
Overheating protection has responded
Check gas supply Check the earth connection of
the power supply
- Check the installation of the
solenoid valve
USA Addition:
Switch off warm-air heater and
allow to cool; if necessary,
fill the boiler with cold water.
Switch warm-air heater on again.
- Check exhaust gas
system
- Replace the ignitor
plug kit
- Replace the solenoid
valve
- Replace the
electronics
USA Addition:
Switch off warm-air
heater and allow to
cool;
if necessary, fill the
boiler with cold water.
Check warm air outlets
and circulated air intake
and remove blockages.
Switch warm-air heater
on again.
203 llss,lsll Flame not expected Ionization voltage present in standby mode Check solenoid valve
(stuck in open position)
206 llss,llls Dirty supply voltage AC components in power supply Check power supply, AC
components also possible
through power supply units or
solar systems
Only operate heater with battery
Page 19/232/16/17 English
List of flash codes Combi (E) Combi 4/15 V05.00.00)
# Flashcode Note Error Error information 1st action 2nd action 3rd action
207 llss,llll Dirty supply voltage AC components in power supply Check power supply, AC
components also possible
through power supply units or
solar systems
Only operate heater with battery
208 llsl,ssss Speed of the combustion air motor
too low
The speed of the combustion air motor is
too low or outside the tolerance
If the SW index is lower than
V03.00.04, replace the
electronics
Replace the combustion air
motor
209 llsl,sssl RPM of combustion engine too high - Combustion air motor running too fast or
outside tolerance range
- Ignition spark interfering with electronics
Ignitor must have orange label,
otherwise replace ignitor
Replace the ignitor with a new
ignitor with index 05
Replace combustion air
motor and / or
electronics
210 llsl,ssls Electronic fault Failure in electronic PCB Restart heater Check power supply
211 llsl,ssll Flame unstable Flame unstable during operation
USA Addition:
Gas cylinder closed
Switch for gas shut-off valve open
Overheating protection has responded
Check gas supply
USA Addition:
Gas cylinder closed
Switch for gas shut-off valve
open
Overheating protection has
responded
Check flue system
USA Addition:
Switch off warm-air heater and
allow to cool; if necessary, fill the
boiler with cold water. Switch
warm-air heater on again.
- Change ignition plugs
- Change electronics
USA Addition:
Check warm air outlets
and circulated air intake
and remove blockages.
Switch warm-air heater
on again.
Page 20/232/16/17 English
List of flash codes Combi (E) Combi 4/15 V05.00.00)
# Flashcode Note Error Error information 1st action 2nd action 3rd action
212 llsl,slss 1) Flame not detected
2) Electronics defective
- Gas supply interrupted
- Error in the electronics
USA Addition:
Combustion air infeed or exhaust gas outlet
closed
Gas pressure regulation system defective
Overheating protection has responded
Electronics defective
Check / replace the gas pressure
regulation system
USA Addition:
Check for obsbsstructions such
as slush, ice or leaves and
remove from openings.
- Restart the heater
- Check the power supply
USA Addition:
Check/ replace gas pressure
regulation system
Check the exhaust gas
system
- Replace the spark
plug set
- Replace the solenoid
valve
- Replace the
electronics
213 llsl,slsl Electronic fault Failure in electronic PCB Restart heater Check power supply
214 llsl,slls Electronic fault Failure in electronic PCB Restart heater Check power supply
215 llsl,slll Electronic fault Failure in electronic PCB Restart heater Check power supply
216 llsl,lsss Electronic fault Failure in electronic PCB Restart heater Check power supply
217 llsl,lssl Electronic defective or combustion
air motor running at incorrect speed
- Failure in electronic PCB
- Combustion air motor defective
- Cable harness defective
Check / replace cable harness Replace the combustion air
motor
218 llsl,lsls Electronic fault Failure in electronic PCB Restart heater Check power supply
219 llsl,lsll Electronic fault Failure in electronic PCB Restart heater Check power supply
220 llsl,llss Electronic fault Failure in electronic PCB Restart heater Check power supply
221 llsl,llsl Electronic fault Failure in electronic PCB Restart heater Check power supply
223 llsl,llll Electronic fault Failure in electronic PCB Restart heater Check power supply
224 llls,ssss Electronic fault Failure in electronic PCB Restart heater Check power supply
Page 21/232/16/17 English
List of flash codes Combi (E) Combi 4/15 V05.00.00)
# Flashcode Note Error Error information 1st action 2nd action 3rd action
225 llls,sssl Electronic fault Failure in electronic PCB Restart heater Check power supply
226 llls,ssls Electronic fault Failure in electronic PCB Restart heater Check power supply
227 llls,ssll Electronic fault Failure in electronic PCB Restart heater Check power supply
228 llls,slss Electronic fault Failure in electronic PCB Restart heater Check power supply
229 llll,slsl Electronic fault Failure in electronic PCB Restart heater Check power supply
230 llls,slsl Electronic fault Failure in electronic PCB Restart heater Check power supply
231 llls,slll Electronic fault Failure in electronic PCB Restart heater Check power supply
232 llls,lsss Electronic fault Failure in electronic PCB Restart heater Check power supply
233 llls,lssl Electronic fault Failure in electronic PCB Restart heater Check power supply
234 llls,lsls Electronic fault Failure in electronic PCB Restart heater Check power supply
235 llls,lsll Electronic fault Failure in electronic PCB Restart heater Check power supply
236 llls,llss Electronic fault Failure in electronic PCB Restart heater Check power supply
237 llls,llsl Electronic fault Failure in electronic PCB Restart heater Check power supply
238 llls,llls Overtemperature of the combustion
air temperature sensor
Electronics locked:
- Because the combustion air temperature
sensor became too hot as a result of
overheating during operation
- Short circuit of the combustion air
temperature sensor
- Check the heater for
overheating damage
(heat exchanger, water storage
tank, in case of frost damage
also check the FrostControl, ..)
Check the exhaust pipe does not
leak
- Check / replace the combustion
air temperature sensor and cable
harness
- Replace the circulating air
motor
- Unlock the electronics
with the Truma
Diagnose Tool ("Lock"
symbol bottom right)
- Replace electronics
Page 22/232/16/17 English
List of flash codes Combi (E) Combi 4/15 V05.00.00)
# Flashcode Note Error Error information 1st action 2nd action 3rd action
239 llls,llll Water temperature switch
over-temperature or air temperature
switch over-temperature
Fault:
- Because the air temperature switch and /
or water temperature switch opened during
operation due to over-heating
- Check the heater for
over-heating damage
- Check the thermostat plate /air
temperature switch / air
temperature sensor for damage
caused by overheating
=> Inform the customer service
- Check / replace the water
temperature switch and water
temperature sensor
- Check / replace the air
temperature switch / sensor and
cable
- Check / replace the circulating
air motor
240 llll,ssss Air temperature switch
over-temperature or water
temperature switch
over-temperature
Fault:
- Because the air temperature switch and /
or water temperature switch opened during
operation due to over-heating
- Check the heater for
over-heating damage
- Check the thermostat plate /air
temperature switch / air
temperature sensor for damage
caused by overheating
=> Inform the customer service
- Check / replace the water
temperature switch and water
temperature sensor
- Check / replace the air
temperature switch / sensor and
cable
- Check / replace the circulating
air motor
255 No connection between heater and
control panel
Heater has no 12 V power supply
Control panel cable faulty
Make connection between heater
and control panel
Ensure that the 12V power
supply is available
Contact Truma Service
Page 23/232/16/17 English