BlkMax

8/20/2019 BlkMax

http://slidepdf.com/reader/full/blkmax 1/167

8/20/2019 BlkMax


INTRODUCTION

We would like to present the 6th edition of the Black Max Operations Handbook. We

hope you will find it concise, easy to read, and to use.Drilling technology is moving at a rapid pace today, both in and out of the field. Newtechniques are developed everyday and can be difficult to keep up with. With this inmind, we set out to gather information and procedures that are commonly used inthe field today, with respect to the operation of the Black Max products.This book is being made with a two-fold purpose:

a) Bridge the gap between users in order to provide greater understanding andcommunication.

b) Provide the drilling operator and rig hands information they will need to ensureproper operation of Black Max products in order to achieve maximum performance.

The manual covers basic procedures and instructions used in the proper operationof Black Max products. This information is provided as a guideline only and must be

used with the necessary precautions. If there is any question as to the correct andsafe use of these products, please contact your nearest Black Max representative.

If you think there is anything that we missed (procedures, formulas, diagrams, etc.)that would help you to run our products in a more efficient manner, contact us at our head office - (780) 955-8828, and we will do our best to incorporate the informationinto the next edition.

8/20/2019 BlkMax


8/20/2019 BlkMax


8/20/2019 BlkMax


WINDOW MILLINGProcedures 132Whipstock Specifications 134Mills 135

FISHINGCanFish Services 136

TABLESMotor Shipping Information 117

Casing Dimensions 149Rotary Connection Cross Reference 151Drill Collar Weights 152

Annular Capacities 153Hole Capacity 154Drill Pipe Capacities 155Drill Pipe Properties 156

Nozzle Flow Areas 157Mud Weights 159Unit Conversions 160

INDEX Previous

8/20/2019 BlkMax


DESCRIPTION

Bearing Assembly - Each Black Max motor comes equipped with a fully sealed, oillubricated bearing system. Bearings are stacked to accommodate high speed/lowtorque or low speed/high torque, without altering radial or axial loading.

Universal Joint Assembly - The Black Max universal joint is used to convert theeccentric motion of the motor (rotor) to a smooth concentric motion required by thebearing section. The simple design of two internally sealed ball bearing style

universal joints and a connecting rod, allows the motor to operate at high angles, yetstill be able to handle high torque and speed.

Adjustable Bent Housing/Fixed Housing - The Black Max line of adjustable

housings are available in 0°-3° settings, and also includes a specialized assemblyfor short radius drilling. The housing is easily adjustable and allows the operator to

reset angles at the rig floor, eliminating the need to change assemblies or motors. Always follow the specifications for proper tightening of the assembly. (See pg. 138-139 for proper procedures)

Black Max also supplies a number of fixed housings in angles from 0° to 4°(depending on the motor size and application). See your Black Max representativefor details.

8/20/2019 BlkMax


Power Section - Black Max power sections are made up of a lobed rotor that fitsinside a rubber lined housing (stator). The rotor has one less lobe than the stator,creating a continuously sealing chamber. Drilling mud or air is forced through themotor, thereby turning the rotor and generating torque. The lower the speed (largenumber of lobes), the more torque is provided, and vice versa.

Where drilling requirements call for circulation rates exceeding maximumrecommended rates, rotors are jetted or bored to allow excessive fluid to flow downa parallel path, thereby reducing damage to the elastomer in the stator.

Dump Valve - optional (see your dealer for more details)

8/20/2019 BlkMax


PROCEDURES

This section describes basic operating procedures, which are used in the field andwill facilitate proper operation of Black Max motors.

An important aspect of any planned downhole motor run is properly matching the bitand hydraulics to the motor in order to achieve the desired results. Attention mustbe given to TFA (total flow area) to see that proper parameters are maintained withregard to pressure drop across bit, annular velocity needed for hole cleaning,

maximum standpipe pressure, and adequate hole cleaning at the bit\formationinterface. Keep in mind that stall pressure of a motor may approach pump relief valve limits in some cases. In larger hole sizes, a bored rotor may be necessary toaccommodate fluid requirements mentioned above. Generally, all motor sizes haveadequate torque to run any cone type bit. If a drag type (PDC or polycrystallinediamond compact) bit is to be used, it should be remembered that the moreaggressive PDC's may cause excessive stalling in rough, broken formations. If thepurpose of the run is to build angle or otherwise achieve significant deviation, gaugelength on the bit is very important. Gauge protection is necessary if the motor isbent, since continual side loading occurs at the bit.

8/20/2019 BlkMax


Surface Testing (& Orientation)

The Black Max motor is a sealed bearing motor, so it may be safely surface testedwith or without a bit attached, since bit pressure drop is not necessary to cool the

bearings. It is recommended that a bit not be attached if the motor is significantlybent, and needs to be positioned in the BOP's (blow-out preventers) or below toaccommodate testing of the dump valve. If the downhole motor is tested in thismanner, be sure to remove the bit box thread protector before lowering the motor into the hole. When the downhole motor is equipped with a dump valve, attach thekelly and lower the ports just below the top of the bell nipple before starting thepump. Carefully observe the closing of the dump valve as the pump is eased up.

After the valve is closed, ease up on the pump. Left-hand torque should be noted inthe assembly. Quite a bit of vibration may be seen as flow rates increase, but isnormal and no cause for concern. Before shutting the pump down, be sure that thedump valve is in position in the bell nipple. When the pump is shut down, if thepressure doesn't bleed off, open the fill-up line on the standpipe to relieve thepressure. When turning the bit box with tongs during the course of a coiled tubingoperation, turn the box to the left, otherwise a twist-off could occur.

Pick the motor up, and attach the chosen bit. If a bent housing adjustment isneeded, lower the motor down to the adjustable, and make the needed changeaccording to the accompanying setting procedure (see pg. 138-140). Uponcompletion of the setting procedure, mark the tool face, and slowly lower the motor into the

8/20/2019 BlkMax


hole, keeping tool face alignment as you go. At this point, you can align and testwhatever steering device is to be used, and proceed on in the hole. Please note,motors are pre-tested in water and should be properly thawed before surface testing,when operating in sub-zero temperatures.

Running In

We recommend running a float valve with the downhole motor, especially if a dumpvalve assembly is employed. This keeps trash out of the ID of the string. If no dumpvalve is used, it (the float) will keep the motor from running backward as the pipe fillsup. When this occurs; it is possible to back something off internally. If heat is afactor, it is a good idea to break circulation (depending on hole depth) once or twice

as you approach bottom. Pumping should be at a slow rate and kept up longenough (calculate surface-to-bit strokes) to move some cool mud down to the motor.Slow movement of the drill string up and down during the pumping operation willkeep casing wear to a minimum, and decrease the likelihood of leaving a ledge if themotor happens to be in open hole. If the motor bend is extreme, keep runningspeeds slow to minimize the chance of ledging. Running speeds should also beslow when dealing with high mud weights and small liners, as pressure surges mightknock the bottom out at the liner shoe.

8/20/2019 BlkMax


Drilling

Drilling with a downhole motor is monitored mainly by changes in standpipepressure. Generally, the amount of torque created at the bit face will be reflected byan increase in standpipe pressure over the "off bottom" reading. This is Differential

Pressure. Keep in mind that the maximum motor differential presented in thedownhole motor specifications is the total differential recommended. It takes from 10to 15% of that total to turn the rotor in the off bottom position. The difference is theamount that is usable with WOB (weight-on-bit).

When tagging bottom for the first time, keep in mind that a new bottom patternneeds to be established, especially if a different assembly or a different bend is

employed. Higher differential pressures will be noted with less bit weight if PDC(drag) bits are used. Regular diamond bits will increase standpipe pressure slightlywhen bottom is tagged due to the reduction in flow area around the bit face.Whether the drilling operation is sliding or rotating, we recommend keepingdifferential at 60-75% of the maximum motor differential noted in the specifications.ROP (rate of penetration) is a function of rpm and tooth penetration. If rpm's aredecreased and tooth penetration is increased, the net effect may not amount tomuch increase in ROP, and it will certainly shorten stator life.Good weight transfer is normally accomplished with rotation of the

8/20/2019 BlkMax


drill string, and optimization of ROP can be attained with incremental changes of WOB. We recommend (for sections of hole where long rotation periods are

anticipated) that bends be kept to a maximum of 1.5° (actual) and surface rotaryspeed be kept below 90 rpm.

If heat is a factor to be considered, special precautions should be taken. If the stator is swelling in heat, chunking of the stator material is most likely to occur after ashutdown of the pumps for whatever reason (survey, connection, repairs, wellcontrol, etc. ). For this reason, pumps should be brought up slowly, get the rotor turning first, then bring them gradually up to normal speed. When going back onbottom, ease into it gradually to minimize the shock to the heat swollen stator, andgive time to get some cool mud around it. It is also helpful to have a good cleanmud system with a lubricant in it that will lower friction between the rotor and stator.

As a rule, anything that helps lower friction between the drill string and the hole willalso help on the inside of the motor.

A motor stall is indicated when a sudden pressure increase is noted whiledrilling. When this occurs, it is imperative to immediately cut back on pumpstroke before lifting the motor up off bottom, especially if you are in the

rotating mode. This will reduce the increase in differential pressure that wascreated when the stalling occurred. If the rotor is not turning, and the drillstring is turning, the stator is spinning backward on the rotor, and failure willlikely occur in short order.

8/20/2019 BlkMax


8/20/2019 BlkMax


APPLICATIONS

Black Max now supplies one of the widest range of motor sizes available. It is thisvariety that allows us the flexibility to participate in almost any application withmaximum performance.

Performance\Straight Hole Drilling

With the advent of PDC bits and ever more powerful downhole motors, it hasbecome cost effective to pair the two when long straight hole sections are to be

drilled. PDC bits depend on rpm to make hole, and downhole motors are able todeliver the rpm to the bit with only minimum rotation on the drill string, thus savingwear and tear on both rig and drill string.

Black Max offers a full line of motors that have proven themselves in very deep, hot,high mud weight, small hole applications. The savings recognized by operators dueto reduced tubulars cost and savings in mud systems far outweighs the cost of motor

operation at depth.

Directional\Steerable Drilling

Black Max motors offer a surface adjustable bent housing that provides directionaldrillers with flexibility in the planning and execution of any directional drilling project.

The 3° adjustable sub allows the handling of any conventional open hole KO (kick-off) or sidetracking off a cement plug or drilling below a casing whip stock window.

8/20/2019 BlkMax


The motors can be oriented with single shots, steering tools (magnetic or gyro) andMWD's (measurement-while-drilling). Left-hand reactive torque must becompensated for if orienting with single shots in a fluid circulating medium.

If a steerable system is to be used, Black Max motors again display their versatilitywith the screw on stabilizer on the bearing housing, thus providing one basicelement of a 'steerable system', the others being a durable, long range bit, and anMWD device with steering and possibly formation evaluation capabilities. Steerablesystems are invaluable to wells that have multiple targets, or complex approachpaths that are the result of geological constraints. The stabilization provided isnormally 1/8 to 1/4 inch less than hole gauge and can be tailored to the individual

needs of the directional driller, because of the rig site interchangeable stabilizer capability.

Horizontal / Short Radius Drilling

Black Max has a range of motor sizes suited to horizontal and short radiusapplications in various hole sizes. Black Max motors have performed medium radius

projects with build rates ranging from 10°-45°/100'. Short radius (46°-95°/100 ft.)and ultra-short radius projects (96°-128°/100 ft.) are also becoming morecommonplace. For angle building purposes, the motors can be run with or without anear bit stabilizer, with a single bend, with a double bend, or with

8/20/2019 BlkMax


a flex joint in place of the second bend at the top of the motor. The flex joint allowslimited rotation during the build section to fine tune build rate. The flex joint alsorelieves strain at the top of the stator housing, and facilitates going through the curvesection during trips. When rotating in the lateral section we recommend a bent

housing maximum setting of 1.5

° (actual). This should be sufficient for minor course

corrections as drilling proceeds, and is sometimes enough to accomplish an openhole sidetrack on the low side, if a short gauge bit is being used.

Remedial\Workover Operations

Black Max provides a wide variety of power section options and motor sizes that will

accommodate almost any remedial need. Trying to rotate a small limber work stringat great depth with a power swivel is a headache at best, and nearly impossible in adeviated hole. Drilling out cement and guide shoes in small liners is efficiently andcost effectively accomplished by utilizing Black Max downhole motors.

Coiled Tubing

Black Max motors have been used for years to provide a power source for coiledtubing remedial operations. Recently, Black Max Motors have been used for drillingnew holes. Motor sizes range from 1 11/16”-5” O.D.. Torque restrictions in thecoiled tubing so far have limited hole size applications, but drilling rates have beenimpressive, using both fluid and air as a circulating medium.

8/20/2019 BlkMax


Air Drilling

Black Max motors, due to their sealed bearing assembly, have proven themselveshighly adaptable to air drilling projects. The higher rotor/stator lobe configurationswith their high torque and slow rpm outputs have been the most successful. In anyair circulating medium, there must be some form of lubricant (mist, soap, petroleumbase, or polymer) to lower friction and heat generated between the rotor and stator.Dump valves cannot be used when air is the circulating medium.

Air volume requirements for various sizes of downhole motors are hard to equate withnon-compressible fluid. We have included an equation to give a starting point for

calculating air requirements relative to fluid requirements. The equation assumes anefficiency for compressor output, and an efficiency for the motor relative to fluidefficiency. Keep in mind that as the rotor turns, heat is generated that may cause stator swelling (possibly increasing standpipe pressure), thus affecting a decrease involumetric air delivery at the motor. Therefore, these volume calculations are meant asa loose guideline. Remember, lubrication is the key to good performance. We do not,in any circumstance, recommend running the downhole motor on dry air. This will result

in premature failure of the power section and cause damage to the motor.

8/20/2019 BlkMax


Air Volume Formula:P1= Atmospheric or Surface Pressure (psi)

V1= Compressor Rated Output (cfm)

P2= Pressure above the Power Section (psi)

Pb= Bottom hole Pressure (psi)Pd= Differential Pressure across the Motor (cfm)V2= Equivalent cfm delivered to the Motor (cfm)

Choose gpm from motor specifications (gpm). This is Vm.When using fluid as a lubricant, subtract it from the chosen volume.

eg.

2.

3.

NOTE: V1 does not include compressor and motor efficiency.

lub1 V V V mm −=

)(48.7

)(

3

12

ft gal

gpmV V

m=

1

221

P

V P

V

×=

8/20/2019 BlkMax


Since air compressor is able to compress air to high pressures and therefore, todifferent volumes at exit, a standard measurement is used for the intake volumetricrate of air. This volumetric rate is stated in standard cubic feet per minute (SCFM),which is a cubic foot of air at standard atmospheric conditions (14.696 psia and 59ºF) having a specific weight of 0/0765 lb/ft3.

Operating the downhole motor with air requires certain precautions. Start the drillingoperation after each connection with the bit just off bottom. Start up thecompressors and build up to motor requirements and ease weight on bit gently.Remember there is no dampening of vibration and shock, so be careful whenslacking off. Cut back on flow rate (50%) when off bottom. Motor stalls are hard to

detect quickly on the standpipe, but vibration of the drill string, and subsequent lackthereof, is a decisive indicator of motor stall. Contact your nearest Black Maxrepresentative for more information.

River Crossing\Utility Boring

Black Max is a recognized leader in the river crossing and utility boring industry. With

crossing projects being undertaken in formations with considerable compressivestrength, the addition of downhole motors with high torque deliverability and built indirectional capabilities was inevitable. The sealed bearing assembly protects thebearing section when solids control is less than perfect. The wide range of rotor/stator configurations have proven to be invaluable to contractors who engage in the highlyspecialized crossing field.

8/20/2019 BlkMax


In a typical crossing operation, the bit enters the ground at an angle less thanhorizontal, proceeds down under the object to be crossed, is brought horizontal, thenback up to an exit point on the other side. The assembly is guided with a wirelinesteering tool, or a surface interactive sonde that can track the bit from above ground.The downhole motor is used on the pilot hole operation, with subsequent holeopening operations bringing the borehole to required diameter.

Small diameter motors are being used more and more for utility boringoperations in urban areas to install fiber optic cables and other utility conduits.The Black Max downhole motors have proven themselves to be cost-effectivewhen compared to alternative horizontal boring methods. Guidance for these

bores is similar to that described above.

8/20/2019 BlkMax


FORMULAS

Horsepower

Pressure

5,252speedtorquehp (rpm)lb)(ft ×= ⋅mechanical

1,714

rateflowdroppressurehp

(gpm)(psi) ×=hydraulic

)(in

(ppg(gpm(psi2

2

areanozzle10,858)weightfluid)rateflow)P

××=bit across the

(ppg)weightmudoriginal

(ppg)weightmudnew(psi)mudoriginaldrop,press.(psi)P

×=ected exp

(ppg)(ft) weightfluiddepthvert.total0.052(psi)P ××=chydrostati

8/20/2019 BlkMax


Velocity

Motor Efficiency

Buoyancy

Note: In order to calculate the correct drill collar string weight, the buoyancy factor must betaken into account. Using the table found on pg. 161, take the mud weight value you areusing and insert it in the above formula. Multiply the resulting buoyancy factor to the weightof the string in air. This will give you the weight of the string in the mud you are using.

(in)(in)

(gpm(ft/s

22O.D.gdrillstrinO.D.hole

)rateflow0.4085)v

−

×=annular

)(in

(gpm(ft/s)2

areanozzle

)rateflow0.3209v ×= jet

(gal/ft)

e)(gal/strok(spm)(ft/min)

capacityannular

outputpumpspeedpumpvel.ann.

×= pump

(psi)pressure(gpm)rateflow

(rpm)speedlb)(fttorque32.64%

×

×⋅×=

65.5

(ppg)weightmud65.5factor buoyancy

−=

8/20/2019 BlkMax


RADIUS OF CURVATURE

Displacement Build Chart in Meters

Horizontal Displacement (meters)

TrueVerticalDepth(m

eters)

10090

8070

6050

40 deg / 30 m

30 deg / 30 m

25 deg / 30 m

22 deg / 30 m20 deg / 30 m

18 deg / 30 m

16 deg / 30 m

40 80 1200 160 200 240 280 320 360

0

40

80

120

160

200

240

280

320

360

14 deg / 30 m

12 deg / 30 m

10 deg / 30 m

9 deg / 30 m

8 deg / 30 m

7 deg / 30 m

6 deg / 30 m

5 deg / 30 m

Displacement Build Chart in Feet

Horizontal Displacement (feet)

TrueVertic

alDepth

(feet)

0

100

200

300

400

500

600

700

800

900

1000

1100

1200

100 200 3000 400 500 600 700 800 900 1000 1100 1200

5 deg / 100 ft

14 deg / 100 ft

12 deg / 100 ft

10 deg / 100 ft

9 deg / 100 ft

8 deg / 100 ft

7 deg / 100 ft

6 deg / 100 ft

16 deg / 100 ft

22 deg / 100 ft

40 deg / 100 ft

18 deg / 100 ft

25 deg / 100 ft

20 deg / 100 ft

30 deg / 100 ft

100

70

90

60

80

50

8/20/2019 BlkMax


Build Rate Formula (Approximate)

D = hole diameter or bit diameter P = pad diameter T = tool diameter B = bit to bend length (including bit length)F = factor, use table below

1.

2.

3.

×

−= −

B2

PDtanu

1

( )( )

2cosF2

uFsin

cosF

2

T

2

PDB

2

P-D

R

2

2

−

−×−−++

=

pR

216,000/100ft.ratebuild =

8/20/2019 BlkMax


If no pad is present on the tool, then P=T. All dimensions are in inches and angles in degrees.

Tool Setting Factor ‘F’

0 00.39 0.25

0.78 0.50

1.15 0.75

1.50 1.00

1.83 1.252.12 1.50

2.38 1.75

2.60 2.00

2.77 2.25

2.90 2.502.97 2.75

3.00 3.00

8/20/2019 BlkMax


FLUID BYPASS CALCULATIONS

The following calculations are supplied in order to obtain the correct jet sizes for fluidbypass requirements:

FORMULAS:

h (pressure) = ft of head

Q (flow rate) = ft3/min

v (velocity) = [(2gh)/SP] 1/2 = ft/min

SP (specific gravity) = density of mud density of water

A (flow area) = Q = ft2

v

g (gravity) = 32.2 ft/s²

8/20/2019 BlkMax


SAMPLE CALCULATION:

Jet size needed for bypassing 60 gpm of 12.2 lb mud at 360 psi:

SP = density of mud = 12.2 lb/gal = 1.46 density of water 8.34 lb/gal

v = [(2gh)/SP] 1/2 = [(2)(32.2 ft/s²)(360 psi x 2.31)/1.46] 1/2

= 191.52 ft/s x 60 s/min

= 11,491 ft/min

Q = 60 gal/min. = 60 gal / min

7.481 gal / ft3

= 8.02 ft3/min.

A = Qv = 8.02 ft / m in

11,491ft / min

3

= 0.0007 ft2

8/20/2019 BlkMax


Hole ∅ = (4 A/Π) 1/2 = [(4)(0.0007 ft2)/Π] 1/2 = 0.0298 ft

= 0.3576 in

Jet size = Hole ∅ x *32

= 0.3576 in. (32)

= 11.4

*('32' refers to an incremental value needed to obtain jet size - see most bit manuals)

∴USE BIT JET SIZE OF #11 OR #12

8/20/2019 BlkMax


8/20/2019 BlkMax


Another important factor to keep in mind is mud weight. As a rule, heavier mudweights create more wear on the motors. Combined with high sand content, thiscould be extremely detrimental to the motor. Generally, when using heavier muds,ie. 12 lb +, extreme care should be taken to keep sand content as low as possible to

prevent washing in the motor. Sand content should not be greater than 1/2%going in. Contact a Black Max representative for more information.

Temperature is also a factor in performance. In the case of hot hole applications,Black Max will supply specialized power sections. DO NOT attempt to use these inareas of lower temperature. These stators have a loose fit designed to incorporate

swelling or specialty elastomers (eg. HSN). If used in lower temperatures, it will onlyprovide a small percentage of power specified.

8/20/2019 BlkMax


FLUID TYPE ELASTOMER RECOMMENDATIONS

ASTM #3

Neither HSN nor Nitrile elastomers are suitable for use in ASTM #3 oil, due to its low aniline point. HSN seems to holdits properties at 350 F, but any drop in temperature will makeit unsuitable.

CUTTER D

Standard Nitrile is not suitable for use with Cutter D, due tohigh volume swell.HSN should work well to 250 F, provided proper fit ismaintained.

DIESEL

Standard Nitrile is not suitable for use with diesel, due to high

volume swell.Oversize stators of HSN elastomer are well suited to diesel.

INVERMULEHSN is suitable for use in Invermule.Standard Nitrile is not suitable for Invermule mud.

LIGNO-SULPHONATE

Both Nitrile and HSN are suitable for use in Lignosulphonite. An oversize stator is recommended for Nitrile.

MENTOR 26

Both Nitrile and HSN are suitable for use in Mentor 26, up to

temperatures of 350 F. An oversize stator is recommended for thermal expansion.

MUDZYMEBoth Nitrile and HSN are suitable for use in Mudzyme.

An oversize stator is recommended for Nitrile at 250 F.

NITROGENBoth Nitrile and HSN are suitable for drilling with Nitrogenwith the addition of DA-001 as a lubricant.

8/20/2019 BlkMax


8/20/2019 BlkMax


SPECIFICATIONS

The following sections show specifications recommended for the proper operation of Black Max motors.

The performance graphs that accompany the specifications show maximumdifferential working (on/off bottom) pressure, torque, rpm, and horsepower asfollows:

Maximum Pressure Differential: This is the maximum designed pressure dropped

across the illustrated power section. It is indicated on the graph as ‘MAX. DIFF.’. Inthis case, the pressure differential is 600 psi. For optimum performance and life, thispressure should not be exceeded.

Working Pressure: Due to losses from friction, turbulence, and pressure, theWorking Pressure will be less than the Maximum Pressure Differential:

To determine the working pressure at 175 gpm, find the line marked ‘rpm-175 gpm’.There is 75 psi indicated on the graph as ‘Press. Loss’. This is the pressure lossthrough the motor at 175 gpm with no load on the bit. Therefore,

LossPressurePressurealDifferentiMaximumPressureWorking −=

ipsi75psi600PressureWorking ps525=−=

8/20/2019 BlkMax


It is offset to the left of the ‘MAX. DIFF.’ line by an amount equal to the pressure loss(75 psi). Reading this line across the graph to the right will give you a Torquereading. For this example, torque is 1600 ft-lb.Rpm: To read rpm, find the line labeled ‘rpm-175 gpm’, and follow it to where itintersects the line labeled ‘MAX. DIFF.’. Reading across the graph to the left, the

rpm is 133 rpm.Horsepower : To determine the horsepower you must know the rpm and the torqueat which you are running.

{PRES.

LOSS

40

80

120

200100 300 400

rpm - 100 gpm

T O R Q

U E

{

}

160

200

240

280

320

rpm - 250 gpm

rpm - 175 gpm

LOSS

PRES.

PRES.LOSS

300

600

900

500 600 700 800

1,200

1,500

1,800

2,100

2,400

MAX.DIFF

.

PRESSURE DIFFERENTIAL (psi)

SP

EED

(rpm)

TO

RQUE

ftlb

*

40.55252

lbft1600133

5252

torquerpmhp =

⋅×=

×=

8/20/2019 BlkMax


1 11/16" 1.68" 1-2 3 STAGE (168-1)

PRESSURE DIFFERENTIAL psi

rpm - 15 gpm

SPEED

rpm

500

250

750

150

75

225

300

T O R Q U E

1,750

1,250

1,000

1,500

2,000

rpm - 25 gpm

rpm - 35 gpm

TORQ

UE

ftlb

15

10

5

375

450

525

600

40

35

30

25

20

MAX.D

IFF.

.

Stator Configuration 1 11/16" 1.68" 1-2, 3 Stage

Bearing Assembly 1 11/16" 43 mmVolume 15-35 gpm 57-133 lpm

Speed 534-1,756 rpm

Torque 25 ft-lb 34 N *m

Max. Pressure Drop 1,500 psi 10,342 kPa

Max. Diff. Pressure 450 psi 3,103 kPa

Bit To Bend Length 22" 559 m m

O/A Length 86" 2,184 mm

Hole Size 1 7/8"-3" 48-76 m m

Top Connection AW -RO D

Bottom Connection AW -RO D

Bearing Load dynamic=2,500 lb 1,110 daN

(compression) static=6,000 lb 2,670 daN


(tension) static=6,000 lb 2,670 daN

Max. Overpull

(for re-runs)

Ab so lu te Overp ull 28,000 lb 12,455 daN

6,000 lb 2,670 daN

Volume(gpm)

Speed(rpm)

Torque(ft-lb)

hp

15 534-797 25 2.5

25 976-1,238 25 4.6

35 1,492-1,756 25 7.1

8/20/2019 BlkMax


8/20/2019 BlkMax


PERFORMANCE

100

200

300

400

500

600

700

800

100 200 300 400 500 600 700 800

20

40

60

80

100

120

140

160

TORQUE

FTLB

SPEED

RPM

PRESSURE DIFFERENTIAL PSI

rpm - 15 gpm

MAX.D

IFF.

1 11/16" 1.68" 5-6 5 STAGE (168-3)

T O R Q U E

rpm - 30 gpm

rpm - 45 gpm



Speed 0 - 645 rpm




Bit to Bend Length 22" 559 mm


Hole Size 1 7/8"-3" 48-76 mm

Top Connection AW-ROD

Bottom Connection AW-ROD





Max. Overpull 6,000 lb

(for re-runs)

Ab so lu te Ov erpu ll 28, 000 l b 12 ,4 55 da N

2,670 daN

Volume(gpm)

Speed(rpm)

Torque(ft-lb)

hp

15 0-212 103 0.0

30 35-430 103 0.7

45 190-645 103 3.7

8/20/2019 BlkMax


200

400

600

800

1,000

1,200

1,400

1,600

50

100

150

200

250

300

350

400

5

10

15

20

25

30

35

40

MAX

.DIFF.

rpm - 25 gpm

rpm - 35 gpm

rpm - 45 gpm

T O R Q U E

2 1/16" 2.06" 1-2 2 STAGE (206-1)

SPEED

rpm


TORQUE

ftlb.



Speed 575-1,219 rpm





O/A Length 105" 2,667 m m

Hole Size 2 7/16"-3 1/2" 62-89 m m







Max. Overpull

(for re-runs)

Abso lu te Overpu ll 33,500 lb 14,900 daN

2,300 lb 1,025 daN

Volume(gpm)

Speed(rpm)

Torque(ft-lb)

hp

25 575-683 25 2.7

35 852-960 25 4.1

45 1,111-1,219 25 5.3

8/20/2019 BlkMax


HOT HOLE

50

100

150

200

250

300

350

400

25

50

75

100

125

150

175

200

10

20

30

40

50

60

70

80

rpm - 20 gpm

MAX.D

IFF.

rpm - 35 gpm

rpm - 50 gpm

T O R Q U

E

2 1/16" 2.06" 4-5 1 STAGE (206-2)

SPEED

rpm


TORQUE

ftlb.



Speed 92-303 rpm




Bit to Bend Length 29" 737 m m


Hole Size 2 7/16"-3 1/2" 62-89 mm







Max. Overpull

(for re-runs)


2,300 lb 1,025 daN

Volume(gpm)

Speed(rpm)

Torque(ft-lb)

hp

20 92-118 52 0.9

35 187-213 43 1.5

50 277-303 39 2.0

8/20/2019 BlkMax


8/20/2019 BlkMax


200

400

600

800

1,000

1,200

1,400

1,600

150

300

450

600

750

900

1,050

1,200

15

30

45

60

75

90

105

120

rpm - 20 gpm

rpm - 35 gpm

rpm - 50 gpm

MAX.DIFF.

T O R Q U E

2 3/8" 2.37" 1-2 7 STAGE (237-1)

SPEED

rpm


TORQUE

ftlb.



Speed 400-1,363 rpm






Hole Size 3 1/8"-4 1/2" 79-114 m m

Top Connection BW-ROD

Bottom Connection BW-ROD

Bearing Load dynam ic=8,800 lb 3,915 daN




Max. Overpull

(for re-runs)

Ab so lu te Ov er pu ll 40,500 lb 18,015 daN

2,650 lb 1,180 daN

Volume(gpm)

Speed(rpm)

Torque(ft-lb)

hp

20 400-549 85 6.5

35 815-963 85 13.2

50 1,215-1,363 85 19.6

8/20/2019 BlkMax


125

250

375

500

625

750

875

1000

75

150

225

300

375

450

525

600

15

30

45

60

75

90

105

120

rpm - 20 gpm

MAX.DIFF

.

T O R Q U E

2 3/8" 2.37" 2-3 4.0 STAGE (237-4)

SPEED

rpm


TO

RQUE

ftlb.rpm - 45 gpm

rpm - 65 gpm

Stator Configuration 2 3/8" 2.37" 2-3, 4.0 Stage

Bearing Assembly 2 3/8" 60 mmVolume 20-65 gpm 76 - 247 lpm

Speed 168-912 rpm

Torque 95 ft-lb 129 N*m





Hole Size 3 1/8"-4 1/2" 79-114 mm

Top Connection B W -ROD

Bottom Connection B W -ROD





Max. Overpull 2,650 lb

(for re-runs)

Ab so lu te Over pu ll 40 ,500 lb 18 ,0 15 da N

1,180 daN

Volume(gpm)

Speed(rpm)

Torque(ft-lb)

hp

20 168 - 287 95 3.0

45 534 - 634 93 9.5

65 814 - 912 91 14.1

8/20/2019 BlkMax


8/20/2019 BlkMax


8/20/2019 BlkMax


125

250

375

500

625

750

875

1,000

100

200

300

400

500

600

700

800

30

60

90

120

150

180

210

240

MAX

.DIFF.

T O R Q

U E

rpm - 20 gpm

rpm - 45 gpm

rpm - 70 gpm

2 7/8" 2.87" 1-2 5.2 STAGE (287-1)

SPE

ED

rpm


TORQUE

ftlb.



Speed 145-780 rpm




Bit to Bend Length 40" 1,016 mm


Hole Size 3 1/2"-4 1/2" 89-114 m m

Top Connection 2 3/8 Reg., N-Rod

Bottom Connection 2 3/8 Reg., N-Rod





Max. Overpull

(for re-runs)


4,300 lb 1,915 daN

Volume(gpm)

Speed(rpm)

Torque(ft-lb)

hp

20 145-220 153 4.2

45 425-570 153 12.4

70 715-780 153 20.8

8/20/2019 BlkMax


125

250

375

500

625

750

875

1,000

125

250

375

500

625

750

875

1,000

30

60

90

120

150

180

210

240

MAX

.DIFF.

T O R Q

U E

rpm - 40 gpm

2 7/8" 2.87" 2-3 7 STAGE (287-7)

SPE

ED

rpm


TORQUE

ftlb.

rpm - 55 gpm

rpm - 70 gpm


Bearing Assembly 2 7/8" 73 mmVolum e 40-70 gpm 151-265 lpm

Speed 369-845 rpm

Torque 182 ft-lb 247 N*m



Bit to Bend Length 40" 1,016 m m


Hole Size 3 1/2"-4 1/2"

Bit Conn. 2 3/8 Reg., N-Rod

Top Conn. 2 3/8 Reg., N-Rod





Max. Overpull 4 ,300 lb 1,915 daN

(for re-runs)

Abso lu te Ov er pu ll 62 ,000 lb 27 ,5 80 da N

Volume(gpm)

Speed(rpm)

Torque(ft-lb)

hp

40 369 - 495 182 12.7

55 539 - 668 182 18.6

70 719 - 845 180 24.6

8/20/2019 BlkMax


50

100

150

200

250

300

350

400

75

150

225

300

375

450

525

600

25

50

75

100

125

150

175

200

MAX.DIFF.

T O R Q

U E

rpm - 25 gpm

2 7/8" 2.87" 3-4 4 STAGE LOW FLOW (287-2)

SPEED

rpm


TORQUE

ftl b

.

rpm - 40 gpm

rpm - 10 gpm



Speed 50-320 rpm






Hole Size 3 1/2"-4 1/2" 89-114 m m

Bit Conn. 2 3/8 Reg., N-Rod

Top Conn. 2 3/8 Reg., N-Rod





Max. Overpull

(for re-runs)


4,300 lb 1,915 daN

Volume(gpm)

Speed(rpm)

Torque(ft-lb)

hp

10 50-75 143 1.4

25 172-197 142 4.7

40 290-320 141 7.8

LOW FLOW

8/20/2019 BlkMax


75

150

225

300

375

450

525

600

1 0 0

2 0 0

3 0 0

4 0 0

5 0 0

6 0 0

7 0 0

8 0 0

40

80

120

160

200

240

280

320

rpm - 20 gpm

M A X

. D I F F .

T O R Q

U E

2 7/8" 2.87" 5-6 3.3 STAGE (287-4)

S P E E D

r p m


T O R Q U E

f t l b .

rpm - 50 gpm

rpm - 80 gpm



Speed 65-417 rpm






Hole Size 3 1/2"-4 1/2" 89-114 mm







Max. Overpull

(for re-runs)

Abs olu te Ove rpu ll 62,000 lb 27,580 daN

4,300 lb 1,915 daN

Volume(gpm)

Speed(rpm)

Torque(ft-lb)

hp

20 65-105 190 2.4

50 225-265 183 7.8

80 377-417 167 12.0

8/20/2019 BlkMax


75

150

225

300

375

450

525

600

100

200

300

400

500

600

700

800

75

150

225

300

375

450

525

600

MA

X.DIFF.

T O R Q

U E

2 7/8" 2.87" 7-8 2.5 STAGE (287-6)

SP

EED

rpm


TORQUE

ftl b

.

rpm - 70 gpm

rpm - 90 gpm

rpm - 110 gpm

Stator Configuration 2 7/8" 2.87" 7-8 2.5 Stage


Speed 198-423 rpm






Hole Size 3 1/2"-4 1/2" 89-114 mm







Max. Overpull

(for re-runs)


4,300 lb 1,915 daN

Volume(gpm)

Speed(rpm)

Torque(ft-lb)

hp

70 198-257 250 9.4

90 276-335 215 11.3

110 378-423 180 12.9

8/20/2019 BlkMax


75

150

225

300

375

450

525

600

100

200

300

400

500

600

700

800

75

150

225

300

375

450

525

600

MA

X.DIFF.

T O R Q

U E

3 1/8" 2.87" 7-8 2.5 STAGE (312-1)

SP

EED

rpm


TORQUE

ftl b

.

rpm - 70 gpm

rpm - 90 gpm

rpm - 110 gpm



Speed 198-423 rpm






Hole Size 3 3/4"-4 3/4" 95-121 mm

Top Connection 2 3/8 Reg.

Bottom Connection 2 3/8 Reg.





Max. Overpull

(for re-runs)

Abso lu te Overpul l 68,000 lb 30,250 daN

36,000 lb 16,015 daN

Volume(gpm)

Speed(rpm)

Torque(ft-lb)

hp

70 198-257 250 9.4

90 276-335 215 11.3

110 378-423 180 12.9

8/20/2019 BlkMax


40

80

120

160

200

240

280

320

100

200

300

400

500

600

700

800

150

300

450

600

750

900

1,050

1,200

rpm - 80 gpm

MAX

.D

IFF.

T O R Q

U E

3 1/8" 3.13" 7-8 3 STAGE (312-2)

SP

EED

rpm


TORQUE

ftl b

.rpm - 110 gpm

rpm - 140 gpm


Bearing Assembly 3 1/8" 79 mm

Volume 80-140 gpm 303-530 lpm

Speed 122-249 rpm






Hole Size 3 3/4"-4 3/4" 95-121 m m







Max. Overpull

(for re-runs)


36,000 lb 16,015 daN

Volume(gpm)

Speed(rpm)

Torque(ft-lb)

hp

80 122-141 665 13.8

110 170-189 560 18.1

140 230-249 440 19.3

PERFORMANCE

8/20/2019 BlkMax


75

150

225

300

375

450

525

600

100

200

300

400

500

600

700

800

75

150

225

300

375

450

525

600

rpm - 70 gpm

MAX.DIFF.

T O R Q

U E

3 1/8" 3.13" 7-8 4 STAGE (312-3)

SP

EED

rpm


TORQUE

ftl b

.

rpm - 90 gpm

rpm - 110 gpm




Speed 198-432 rpm






Hole Size 3 3/4"-4 3/4" 95-121 m m







Max. Overpull

(for re-runs)


36,000 lb 16,015 daN

Volume(gpm)

Speed(rpm)

Torque(ft-lb)

hp

70 198-250 422 15.9

90 276-328 395 20.8

110 348-400 355 23.5

8/20/2019 BlkMax


150

300

450

600

750

900

1,050

1,200

125

250

375

500

625

750

875

1,000

50

100

150

200

250

300

350

400

MAX

.DIFF.

rpm - 120 gpm

rpm - 150 gpm

rpm - 180 gpm

T O R Q U E

3 3/8" 3.37" 1-2 5 STAGE (338-1)

SPEED

rpm


TORQUE

ftlb.


Bearing Assembly 3 3/8" 86 m m


Speed 490-933 rpm






Hole Size 4 1/4" - 5 7/8" 108-149 m m

Top Connection 2 3/8 Reg., 2 3/8 IF

Bottom Connection 2 3/8 Reg., 2 7/8 Reg.





Max. Overpull

(for re-runs)


36,650 lb 16,300 daN

Volume(gpm)

Speed(rpm)

Torque(ft-lb)

hp

120 490-640 320 29.6

150 636-786 320 38.8

180 783-933 320 47.7

8/20/2019 BlkMax


50

100

150

200

250

300

350

400

100

200

300

400

500

600

700

800

75

150

225

300

375

450

525

600

rpm - 30 gpmMAX.DIFF.

T O R Q

U E

3 3/8" 3.37" 4-5 5 STAGE (338-2)

SPEED

rpm


TO

RQUE

ftlb.

rpm - 75 gpm

rpm - 120 gpmStator Configuration 3 3/8" 3.37" 4-5, 5 Stage



Speed 66-366 rpm






Hole Size 4 1/4" - 5 7/8" 108-149 m m







Max. Overpull

(for re-runs)


36,650 lb 16,300 daN

Volume(gpm)

Speed(rpm)

Torque(ft-lb)

hp

30 66-86 435 5.5

75 206-226 430 16.9

120 346-366 415 27.4

8/20/2019 BlkMax


25

50

75

100

125

150

175

200

75

150

225

300

375

450

525

600

150

300

450

600

750

900

1,050

1,200

rpm - 60 gpm

MA X

.DIFF.

T O R Q

U E

3 3/8" 3.37" 7-8 3 STAGE (338-4)

SPEED

rpm


TO

RQUE

ftlb.

rpm - 90 gpm

rpm - 120 gpm




Speed 74-180 rpm

Torque 764 ft-lb 1,036 N*m





Hole Size 4 1/4" - 5 7/8" 108-149 m m







Max. Overpull

(for re-runs)


36,650 lb 16,300 daN

Volume(gpm)

Speed(rpm)

Torque(ft-lb)

hp

60 74-95 764 10.8

90 120-143 660 15.1

120 159-180 540 16.3

8/20/2019 BlkMax


50

100

150

200

250

300

350

400

100

200

300

400

500

600

700

800

100

200

300

400

500

600

700

800

rpm - 60 gpm

MAX.DIFF.

rpm - 90 gpm

rpm - 120 gpm

T O R Q U E

3 3/8" 3.37" 9-10 3 STAGE (338-6)

SPEED

rpm


TO

RQUE

ftlb.




Speed 125-317 rpm






Hole Size 4 1/4" - 5 7/8" 108-149 m m







Max. Overpull

(for re-runs)

Abso lu te Ov erpu ll 95,000 lb 42,255 daN

36,650 lb 16,300 daN

Volume(gpm)

Speed(rpm)

Torque(ft-lb)

hp

60 125-159 475 11.3

90 203-234 420 16.2

120 283-317 345 18.6

8/20/2019 BlkMax


75

150

225

300

375

450

525

600

100

200

300

400

500

600

700

800

100

200

300

400

500

600

700

800

rpm - 30 gpm

MAX.DIFF.

T O R Q

U Erpm - 75 gpm

rpm - 120 gpm

3 3/4" 3.37" 4-5 5 STAGE (375-2)

SP

EED

rpm


TORQUE

ftl b

.




Speed 66-366 rpm






Hole Size 4 3/4" - 5 7/8" 121-149 m m







Max. Overpull

(for re-runs)

Ab so lu te Over pu ll 150,000 lb 66,720 daN

67,500 lb 30,025 daN

Volume(gpm)

Speed(rpm)

Torque(ft-lb)

hp

30 66-86 435 5.5

75 206-226 430 16.9

120 346-366 415 27.4

8/20/2019 BlkMax


25

50

75

100

125

150

175

200

7 5

1 5 0

2 2 5

3 0 0

3 7 5

4 5 0

5 2 5

6 0 0

150

300

450

600

750

900

1,050

1,200

rpm - 60 gpm

M A X

. D I F F .

T O R Q

U E

3 3/4" 3.37" 7-8 3 STAGE (375-4)

S P E E D

r p m


T O R Q U E

f t l b .

rpm - 90 gpm

rpm - 120 gpm




Speed 74-180 rpm



Max. Diff. Pressure 562 psi 3,875 kpa



Hole Size 4 3/4" - 5 7/8" 121-149 m m







Max. Overpull

(for re-runs)


67,500 lb 30,025 daN

Volume(gpm)

Speed(rpm)

Torque(ft-lb)

hp

60 74-95 764 10.8

90 120-143 660 15.1

120 159-180 540 16.3

8/20/2019 BlkMax


8/20/2019 BlkMax


50

100

150

200

250

300

350

400

100

200

300

400

500

600

700

800

100

200

300

400

500

600

700

800

rpm - 60 gpm

MAX.

DIFF.

rpm - 90 gpm

rpm - 120 gpm

T O R Q U E

3 3/4" 3.37" 9-10 3 STAGE (375-6)

SPEED

rpm


TO

RQUE

ftlb.




Speed 125-317 rpm






Hole Size 4 3/4" - 5 7/8" 121-149 m m







Max. Overpull

(for re-runs)

Ab so lu te Overpu ll 150,000 lb 66,720 daN

67,500 lb 30,025 daN

Volume(gpm)

Speed(rpm)

Torque(ft-lb)

hp

60 125-159 475 11.3

90 203-234 420 16.2

120 283-317 345 18.6

8/20/2019 BlkMax


8/20/2019 BlkMax


20

40

60

80

100

120

140

160

75

150

225

300

375

450

525

600

200

400

600

800

1000

1200

1400

1600

MAX.DIFF.

T O

R Q U E

3 3/4" 3.75" 7-8 2.3 STAGE (375-3)

SPEED

rpm


TORQUE

ftlb

rpm - 100 gpm

rpm - 130 gpm

rpm - 160 gpm

Volume(gpm)

Speed(rpm)

Torque(ft-lb)

hp

100 60-76 1,125 12.9

130 83-98 950 15.0

160 106-121 725 14.6




Speed 60-121 rpm

Torque 1,125 ft-lb 1,525 n*m





Hole Size 4 3/4" - 5 7/8" 121-149 mm







Max. Overpull

(for re-runs)


67,500 lb 30,025 daN

PERFORMANCE

8/20/2019 BlkMax


25

50

75

100

125

150

175

200

100

200

300

400

500

600

700

800

200

400

600

800

1000

1200

1400

1600

rpm - 80 gpm

MAX

.DIFF.

rpm - 140 gpm

rpm - 200 gpm

T O R Q U E

4 1/8" 3.87" 6-7 3 STAGE (387-1)

SPEED

rpm


TORQUE

ftl b

.

Stator Configuration 4 1/8" 3 7/8" 6-7, 3 Stage



Speed 65-146 rpm

Torque 1,260 ft-lb 1,709 N*m





Hole Size 4 3/4" - 5 7/8" 121-149 m m







Max. Overpull

(for re-runs)


80,000 lb 35,584 daN

Volume(gpm)

Speed(rpm)

Torque(ft-lb)

hp

80 51-65 1,250 15.5

140 96-110 1,060 22.2

200 146-160 850 25.9

8/20/2019 BlkMax


4 1/8" 3.87" 7-8 2 STAGE (387-2)

S P E E D

r p m


T O R Q U E

f t

l b

.

Stator Configuration 4 1/8" 3 7/8" 7-8, 2 Stage


Speed 45-90 rpm



Max. Diff . Pressure 420 ps i 2,896 kPa



Hole Size 4 3/4" - 5 7/8" 121-149 mm

Top Connect ion 2 3/8 Reg., 2 3/8 IF

Bot tom Connect ion 2 7/8 Reg.




( tension) static=67,500 lb 30,025 daN

Max. Overpull

(for re-runs)


80,000 lb 35,584 daN

Volume(gpm)

Speed(rpm)

Torque(ft-lb)

hp

100 45-55 1,550 13.3

130 63-73 1,325 15.9

160 78-90 1,050 15.6

8/20/2019 BlkMax


75

150

225

300

375

450

525

600

100

200

300

400

500

600

700

800

150

300

450

600

750

900

1,050

1,200

rpm - 100 gpm

rpm - 150 gpm

rpm - 200 gpmMAX.

DIFF.

T O R Q U E

4 3/4" SH 4.75" 1-2 3 STAGE (47S-4)

SPEED

rpm


TORQUE

ftlb.

Stator Configuration 4 3/4" SH 4.75" 1-2, 3 Stage

Bearing Assembly 5.1" 130 mm


Speed 172-450 rpm






Hole Size 5 7/8" - 7 7/8" 149-200 mm







Max. Overpull

(for re-runs)

Abs olu te Overpu ll 143,000 lb 63,605 daN

56,045 daN20,050 lb

Volume(gpm)

Speed(rpm)

Torque(ft-lb)

hp

100 172-220 440 14.4

150 289-337 440 24.2

200 402-450 440 33.7

8/20/2019 BlkMax


40

80

120

160

200

240

280

320

1 0 0

2 0 0

3 0 0

4 0 0

5 0 0

6 0 0

7 0 0

8 0 0

150

300

450

600

750

900

1,050

1,200

rpm - 100 gpm

rpm - 175 gpm

rpm - 250 gpm

M A X . D I F F .

T O R Q U E

4 3/4 SH 4.75" 4-5 2.5 STAGE (47S-5)

S P E E D

r p m


T O R Q U E

f t l b .

Stator Configuration 4 3/4" SH 4.75" 4-5, 2.5 Stage



Speed 65-315 rpm






Hole Size 5 7/8" - 7 7/8" 149-200 mm







Max. Overpull

(for re-runs)

Absolu te Overpull 143,000 lb 63,605 daN

20,050 lb 56,045 daNVolume

(gpm)

Speed(rpm)

Torque(ft-lb)

hp

100 73-91 675 9.4

175 145-164 655 18.1

250 208-236 605 24.0

8/20/2019 BlkMax


40

80

120

160

200

240

280

320

100

200

300

400

500

600

700

800

150

300

450

600

750

900

1,050

1,200

rpm - 100 gpm

rpm - 175 gpm

rpm - 250 gpm

MAX.DIF

F.

T O

R Q U E

4 3/4 SH 4.75" 4-5 3.5 STAGE (47S-1)

SPEED

rpm


TORQUE

ftlb.




Speed 60-236 rpm






Hole Size 5 7/8" - 7 7/8" 149-200 mm







Max. Overpull

(for re-runs)

Absolute Overpull 143,000 lb 63,605 daN

20,050 lb 8,920 daN

Volume(gpm)

Speed(rpm)

Torque(ft-lb)

hp

100 60-91 1,020 11.7

175 132-164 1,000 25.1

250 204-236 950 36.9

8/20/2019 BlkMax


40

80

120

160

200

240

280

320

50

100

150

200

250

300

350

400

150

300

450

600

750

900

1,050

1,200

MAX.DIFF.

rpm - 100 gpm

T O R Q

U E

4.75" SH 5.00" 5-6 2 STAGE (47S-2)

SPE

ED

rpm


TORQUE

ftlb.

rpm - 175 gpm

rpm - 250 gpm

Stator Configuration 4 3/4" SH 5" 5-6, 2 Stage



Speed 81-216 rpm






Hole Size 5 7/8" - 7 7/8" 149-200 mm







Max. Overpull

(for re-runs)


20,050 lb 8,920 daN

Volume(gpm)

Speed(rpm)

Torque(ft-lb)

hp

100 81-85 850 13.1

175 146-151 825 22.9

250 211-216 750 30.1

8/20/2019 BlkMax


20

40

60

80

100

120

140

160

75

150

225

300

375

450

525

600

250

500

750

1,000

1,250

1,500

1,750

2,000

rpm - 100 gpm

MA

X.DIFF.

T O R Q U E

4 3/4" SH 4.75" 7-8 2.2 STAGE (47S-3)

SPE

ED

rpm


TORQUE

ftlb.rpm - 175 gpm

rpm - 250 gpm




Speed 45-130 rpm






Hole Size 5 7/8" - 7 7/8" 149-200 mm







Max. Overpull

(for re-runs)

Absolu te Overpull 143,000 lb 63,605 daN

20,050 lb 8,920 daN

Volume(gpm)

Speed(rpm)

Torque(ft-lb)

hp

100 45-53 1,660 14.2

175 90-98 1,450 24.9

250 122-130 1,150 26.7

8/20/2019 BlkMax


75

150

225

300

375

450

525

600

100

200

300

400

500

600

700

800

150

300

450

600

750

900

1,050

1,200

rpm - 100 gpm

rpm - 150 gpm

rpm - 200 gpmMAX.DIFF.

T O R Q U E

4 3/4" 4.75" 1-2 3 STAGE (475-1)

SPEED

rpm


TORQUE

ftlb




Speed 172-450 rpm






Hole Size 5 7/8" - 7 7/8" 149 - 200 m m







Max. Overpull

(for re-runs)


56,045 daN126,000 lb

Volume(gpm)

Speed(rpm)

Torque(ft-lb)

hp

100 172-220 440 14.4

150 289-337 440 24.2

200 402-450 440 33.7

8/20/2019 BlkMax


40

80

120

160

200

240

280

320

1 0 0

2 0 0

3 0 0

4 0 0

5 0 0

6 0 0

7 0 0

8 0 0

150

300

450

600

750

900

1,050

1,200

rpm - 100 gpm

rpm - 175 gpm

rpm - 250 gpm

M A X .

D I F F .

T O R Q U E

4 3/4 SH 4.75" 4-5 2.5 STAGE (47S-5)

S P E E D

r p m


T O R Q U E

f t l b .




Speed 65-315 rpm






Hole Size 5 7/8" - 7 7/8"" 149-200 mm







Max. Overpull

(for re-runs)

Abso lute Overpull 143,000 lb 63,605 daN

126,000 lb 56,045 daN

Volume(gpm)

Speed(rpm)

Torque(ft-lb)

hp

100 73-91 675 9.4

175 145-164 655 18.1

250 208-236 605 24.0

8/20/2019 BlkMax


40

80

120

160

200

240

280

320

100

200

300

400

500

600

700

800

150

300

450

600

750

900

1,050

1,200

rpm - 100 gpm

rpm - 175 gpm

rpm - 250 gpm

MAX.DIFF.

T O

R Q U E

4 3/4 4.75" 4-5 3.5 STAGE (475-3)

SPEED

r pm


TORQUE

ftlb.




Speed 60-236 rpm

Torque 1,020 ft-lb 1,383 N *m





Hole Size 5 7/8" - 7 7/8" 149-200 mm







Max. Overpull

(for re-runs)

Abs olute Ove rpu ll 143,000 lb 63,605 daN

126,000 lb 56,045 daN

Volume(gpm)

Speed(rpm)

Torque(ft-lb)

hp

100 60-91 1,020 11.7

175 132-164 1,000 25.1

250 204-236 950 36.9

8/20/2019 BlkMax


20

40

60

80

100

120

140

160

75

150

225

300

375

450

525

600

250

500

750

1,000

1,250

1,500

1,750

2,000

rpm - 100 gpm

MA

X.DIFF.

T O R Q U E

4 3/4" 4.75" 7-8 2.2 STAGE (475-5)

SPE

ED

rpm


TORQUE

ftlb.rpm - 175 gpm

rpm - 250 gpm




Speed 45-130 rpm






Hole Size 5 7/8" - 7 7/8" 149-200 mm







Max. Overpull

(for re-runs)

Absol ute Ove rpu ll 143,000 lb 63,605 daN

126,000 lb 56,045 daN

Volume(gpm)

Speed(rpm)

Torque(ft-lb)

hp

100 45-53 1,660 14.2

175 90-98 1,450 24.9

250 122-130 1,150 26.7

PERFORMANCE

8/20/2019 BlkMax


40

80

120

160

200

240

280

320

200

400

600

800

1,000

1,200

1,400

1,600

400

800

1,200

1,600

2,000

2,400

2,800

3,200

MAX.DIFF.

rpm - 100 gpm

T O R Q U E

5" 4.75" 4-5 6.3 STAGE (500-1)

SPEED

rpm


TORQU

E

ftlb.

rpm - 175 gpm

rpm - 250 gpm

Stator Configuration 5" S3 4.75" 4-5, 6.3 Stage

Bearing Assembly 5" 127 m m


Speed 40-236 rpm






Hole Size 5 7/8" - 7 7/8" 149-200 m m



Bear ing Load dynam ic=79,625 lb 35,415 daN




Max. Overpull

(for re-runs)


91,100 lb 40,520 daN

Volume(gpm)

Speed(rpm)

Torque(ft-lb)

hp

100 40-91 1,870 14.2

175 110-161 1,835 38.4

250 185-236 1,790 63.1

AIR

8/20/2019 BlkMax


15

30

45

60

75

90

105

120

75

150

225

300

375

450

525

600

500

1,000

1,500

2,000

2,500

3,000

3,500

4,000

rpm - 100 gpm

MAX

.DIFF.

T O R Q U E

5" AIR 4.75" 7-8 2 STAGE (500-3)

SPE

ED

rpm


TORQUE

ftlb.

rpm - 175 gpm

rpm - 250 gpm

GRAPH BASED ON FLUID RESULTS

Stator Configuration 5" S3 4.75" 7-8, 2 Stage

Bearing Assembly 5" 127 mm


Speed 21-74 rpm





O/A Length 272" 6.909 mm

Hole Size 5 7/8" - 7 7/8" 149-200 m m







Max. Overpull

(for re-runs)

Abso lu te Ov erpu ll 210,000 lb 93,410 daN

91,100 lb 40,520 daN

Volume(gpm)

Speed(rpm)

Torque(ft-lb)

hp

100 21-29 2,650 10.6

175 43-51 2,350 19.2

250 66-74 1,680 21.1

8/20/2019 BlkMax


20

40

60

80

100

120

140

160

60

120

180

240

300

360

420

480

250

500

750

1,000

1,250

1,500

1,750

2,000

rpm - 100 gpm

MAX.DIFF

.

T O R Q U E

5" 4.75" 7-8 2.2 STAGE (500-4)

SPE

ED

rpm


TORQUE

ftlb.

rpm - 175 gpm

rpm - 250 gpm




Speed 45-130 rpm






Hole Size 5 7/8" - 7 7/8" 149-200 m m


Bottom Connect ion 3 1/2 Reg.





Max. Overpull

(for re-runs)


91,100 lb 40,520 daN

Volume(gpm)

Speed(rpm)

Torque(ft-lb)

hp

100 45-53 1,660 14.2

175 90-98 1,450 24.9

250 122-130 1,150 26.7

8/20/2019 BlkMax


20

40

60

80

100

120

140

160

60

120

180

240

300

360

420

480

250

500

750

1,000

1,250

1,500

1,750

2,000

rpm - 100 gpm

MAX.DIFF

.

T O R Q U E

5" 4.75" 7-8 2.2 STAGE (500-4)

SPE

ED

rpm


TORQUE

ftlb.

rpm - 175 gpm

rpm - 250 gpm

Stator Configuration 5" 4.75" 7-8, 2.2 Stage



Speed 45-130 rpm






Hole Size 5 7/8" - 7 7/8" 149-200 m m


Bottom Connect ion 3 1/2 Reg.





Max. Overpull

(for re-runs)


91,100 lb 40,520 daN

Volume(gpm)

Speed(rpm)

Torque(ft-lb)

hp

100 45-53 1,660 14.2

175 90-98 1,450 24.9

250 122-130 1,150 26.7

PERFORMANCE

8/20/2019 BlkMax


20

40

60

80

100

120

140

160

1 0 0

2 0 0

3 0 0

4 0 0

5 0 0

6 0 0

7 0 0

8 0 0

500

1000

1500

2000

2500

3000

3500

4000

M A X . D I F F .

rpm - 150 gpm

T O R Q

U E

5" PERFORMANCE 4-3/4" 7-8 3.8 STAGE (500-6)

S P E E D

r p m


T O R Q U E

f t l b .

rpm - 200 gpm

rpm - 250 gpm

Volume(gpm)

Speed(rpm)

Torque(ft-lb)

hp

150 62-78 2,500 29.5

200 88-104 2,300 38.5

250 112-128 2,050 43.7




Speed 62-128 rpm






Hole Size 5 7/8" - 7 7/8" 149-200 mm







Max. Overpull

(for re-runs)


91,100 lb 40,520 daN

PERFORMANCE

8/20/2019 BlkMax


40

80

120

160

200

240

280

320

100

200

300

400

500

600

700

800

300

600

900

1,200

1,500

1,800

2,100

2,400

MAX

.DIFF.

rpm - 100 gpm

T O R Q U E

5" PERFORMANCE 5" 5-6 4 STAGE (500-2)

SPEED

rpm


TORQUE

ftlb.

rpm - 175 gpm

rpm - 250 gpm

Stator Configuration 5" S3 5" 5-6, 4 Stage



Speed 67-217 rpm






Hole Size 5 7/8" - 7 7/8" 149-200 mm







Max. Overpull

(for re-runs)

Abso lu te Overpu ll210,000 lb 93,410 daN

91,100 lb 40,520 daN

Volume(gpm)

Speed(rpm)

Torque(ft-lb)

hp

100 67-84 1,700 21.7

175 133-150 1,640 41.5

250 200-217 1,550 59.0

PERFORMANCE

8/20/2019 BlkMax


50

100

150

200

250

300

350

400

150

300

450

600

750

900

1, 0

50

1,200

400

800

1,200

1,600

2,000

2,400

2,800

3,200

MAX.DIFF.

rpm - 150 gpm

T O R Q

U E

5" PERFORMANCE 5" 6-7 6 STAGE (500-5)

SPEED

r pm


TORQUE

ftlb.

rpm - 250 gpm

rpm - 350 gpm



Volume 150-350 gpm 568-1,325 lpm

Speed 96-300 rpm



Max. Diff. Pressure 1,044 psi 7,198 kPa



Hole Size 5 7/8" - 7 7/8" 149-200 mm







Max. Overpull

(for re-runs)

Abso lu te Overpu ll210,000 lb 93,410 daN

91,100 lb 40,520 daN

Volume(gpm)

Speed(rpm)

Torque(ft-lb)

hp

150 96-130 2,750 50.3

250 181-215 2,550 87.9

350 266-300 2,350 119.0

8/20/2019 BlkMax


30

60

90

120

150

180

210

240

75

150

225

300

375

450

525

600

400

800

1,200

1,600

2,000

2,400

2,800

3,200

MAX.DIFF.

rpm - 200 gpm

T O R Q U E

5 1/2" 5.50" 7-8 3 STAGE (550-1)

SPEED

rpm


TORQUE

ftlb.

rpm - 275 gpm

rpm - 350 gpm



Volume 200-350 gpm 757-1,325 lpm

Speed 70-160






Hole Size 6 3/4" - 8 3/4" 171-222 m m







Max. Overpull

(for re-runs)


123,700 lb 55,020 daN

Volume(gpm)

Speed(rpm)

Torque(ft-lb)

hp

200 70-92 2,622 34.9

275 98-120 2,400 44.8

350 135-160 2,050 52.7

8/20/2019 BlkMax


8/20/2019 BlkMax


75

150

225

300

375

450

525

600

100

200

300

400

500

600

700

800

200

400

600

800

1,000

1,200

1,400

1,600

rpm - 200 gpm

rpm - 350 gpm

rpm - 500 gpm

MAX.D

IFF.

T O R Q U E

6 1/2" 6.50" 1-2 4 STAGE (650-1)

SPEED

rpm


TORQUE

ftlb.



Volume 200-500 gpm 757-1,893 lpm

Speed 182-522 rpm






Hole Size 7 7/8" - 9 7/8" 200-251 mm

Top Connection 4 1/2 Reg., 4 1/2 H90, 5 H90






Max. Overpull

(for re-runs)

Ab so lu te Overpu ll 275,000 lb 122,320 daN

234,000 lb 104,085 daN

Volume(gpm)

Speed(rpm)

Torque(ft-lb)

hp

200 182-207 1,200 41.6

350 337-362 1,200 77.0

500 497-522 1,200 113.6

8/20/2019 BlkMax


50

100

150

200

250

300

350

400

100

200

300

400

500

600

700

800

500

1,000

1,500

2,000

2,500

3,000

3,500

4,000

MAX.DIFF.

rpm - 300 gpm

rpm - 450 gpm

rpm - 600 gpm

T O R Q

U E

6 1/2" 6.50" 4-5 4.8 STAGE (650-2)

SPEED

rpm


TORQUE

ftlb



Volume 300-600 gpm 1,136-2,271 lpm

Speed 115-292 rpm






Hole Size 7 7/8" - 9 7/8" 200-251 mm







Max. Overpull

(for re-runs)

Abs olu te O ver pul l275,000 lb 122,320 daN

234,000 lb 104,085 daN

Volume( g p m )

S p eed(rpm)

Torque(ft-lb)

h p

300 115-147 2,710 59.4

450 185-217 2,625 92.5

600 260-292 2,550 126.3

8/20/2019 BlkMax


30

60

90

120

150

180

210

240

100

200

300

400

500

600

700

800

750

1,500

2,250

3,000

3,750

4,500

5,250

6,000

MAX.DIFF.

rpm - 300 gpm

T O

R Q U E

rpm - 450 gpm

rpm - 600 gpm

6 1/2 6.50" 7-8 3 STAGE (650-3)

SP

EED

rpm


TORQUE

ftlb.



Volume 300-600 gpm 1,136-2,271 lpm

Speed 63-163 rpm






Hole Size 7 7/8" - 9 7/8" 200-251 m m







Max. Overpull

(for re-runs)


234,000 lb 104,085 daN

Volume(gpm)

Speed(rpm)

Torque(ft-lb)

hp

300 63-80 4,200 50.4

450 105-122 3,770 75.4

600 146-163 3,300 91.8

8/20/2019 BlkMax


25

50

75

100

125

150

175

200

50

100

150

200

250

300

350

400

500

1,000

1,500

2,000

2,500

3,000

3,500

4,000

MAX

.DIFF.

rpm - 200 gpm

rpm - 300 gpm

rpm - 400 gpm

T O R Q U E

6 1/2" 6.50" 8-9 2 STAGE (650-4)

SPEED

rpm


TOR

QUE

ftlb.



Volume 200-400 gpm 757-1,514 lpm

Speed 40-104 rpm






Hole Size 7 7/8" - 9 7/8" 200-251 m m







Max. Overpull

(for re-runs)


234,000 lb 104,085 daN

Volume(gpm)

Speed(rpm)

Torque(ft-lb)

hp

200 40-52 2,500 19.0

300 65-78 2,300 28.5

400 92-104 2,000 35.0

8/20/2019 BlkMax


25

50

75

100

125

150

175

200

75

150

225

300

375

450

525

700

500

1,000

1,500

2,000

2,500

3,000

3,500

4,000

MAX.DIFF.

T O

R Q U E

6 1/2" 6.50" 8-9 3 STAGE (650-5)

SPEED

rpm


TORQUE

f tlb.

rpm - 200 gpm

rpm - 300 gpm

rpm - 400 gpm



Volume 200-400 gpm 757-1,514 lpm

Speed 40-105 rpm






Hole Size 7 7/8" - 9 7/8" 200-251 mm







Max. Overpull

(for re-runs)

Absolut e Overpu ll 275,000 lb 122,320 daN

234,000 lb 104,085 daN

Volume(gpm)

Speed(rpm)

Torque(ft-lb)

hp

200 40-53 3,740 28.5

300 62-78 3,500 41.3

400 90-105 3,150 54.0

8/20/2019 BlkMax


75

150

225

300

375

450

525

600

1 0 0

2 0 0

3 0 0

4 0 0

5 0 0

6 0 0

7 0 0

8 0 0

200

400

600

800

1,000

1,200

1,400

1,600

rpm - 200 gpm

rpm - 350 gpm

rpm - 500 gpm

M A X . D I F F .

T

O R Q U E

6 1/2" S3 6.50" 1-2 4 STAGE (65S-1)

S P E E D

r p m


T O R Q U E

f t l b .

Stator Configuration 6 1/2" S3 6.50" 1-2, 4 Stage


Volume 200-500 gpm 757-1,893 lpm

Speed 182-522 rpm






Hole Size 7 7/8" - 9 7/8" 200-251 mm







Max. Overpull

(for re-runs)

Absolut e Ov erpu ll 289,000 lb 128,550 daN

200,250 lb 89,070 daN

Volume(gpm)

Speed(rpm)

Torque(ft-lb)

hp

200 182-207 1,200 41.6

350 337-362 1,200 77.0

500 497-522 1,200 113.6

8/20/2019 BlkMax


50

100

150

200

250

300

350

400

1 0 0

2 0 0

3 0 0

4 0 0

5 0 0

6 0 0

7 0 0

8 0 0

500

1,000

1,500

2,000

2,500

3,000

3,500

4,000

M A X

. D I F F .

rpm - 300 gpm

rpm - 450 gpm

rpm - 600 gpm

T O R Q

U E

6 1/2"/6 3/4" S3 6.50"/6.75" 4-5 4.8 STAGE (65S-2)

S P E E D

r p m


T O R Q U E

f t l b .

Stator Configuration 6 1/2"-6 3/4" S3 6.5"-6.75" 4-5, 4.8 Stage


Volume 300-600 gpm 1,136-2,271 lpm

Speed 115-292 rpm






Hole Size 8 3/4" - 9 7/8" 222-251 mm



Bearing Load dynamic=130,000 lb 57.825 daN




Max. Overpull

(for re-runs)


200,250 lb 89,070 daN

Volume(gpm)

Speed(rpm)

Torque(ft-lb)

hp

300 115-147 2,710 59.4

450 185-217 2,625 92.5

600 260-292 2,550 126.3

PERFORMANCE

8/20/2019 BlkMax


30

60

90

120

150

180

210

240

1 2 5

2 5 0

3 7 5

5 0 0

6 2 5

7 5 0

8 7 5

1 , 0 0 0

1,500

3,000

4,500

6,000

7,500

9,000

10,500

12,000

M A X . D I F F .

rpm - 300 gpm

rpm - 450 gpm

rpm - 600 gpm

T O R Q U E

6 1/2"/6 3/4" S3 6.50"/6.75" 6-7 5 STAGE (65S-8)

S P E E D

r p m


T O R Q U E

f t l b .

V o l u m e( g p m )

S p e e d( r p m )

T o r q u e(f t - lb)

h p

3 0 0 5 6 - 9 6 6 , 0 0 0 6 4 .0

4 5 0 1 0 0 - 1 3 0 5 , 6 0 0 1 0 6 .7

6 0 0 1 4 3 - 1 7 3 5 , 2 0 0 1 4 1 .6

Stator Configuration


Volume 300-600 gpm ,136-2,271 lpm

Speed 56-173 rpm






Hole Size 8 3/4" - 9 7/8" 222-251 m m







Max. Overpull

(for re-runs)

Ab so lu te Ov erpu ll 289,000 lb 122,320 daN

200,250 lb 104,085 daN

6 1/2"-6 3/4" S3 6.75" 6-7, 5 Stage

PERFORMANCE / AIR

8/20/2019 BlkMax


15

30

45

60

75

90

105

120

7 5

1 5 0

2 2 5

3 0 0

3 7 5

4 5 0

5 2 5

7 0 0

1,000

2,000

3,000

4,000

5,000

6,000

7,000

8,000

M A X

. D I F F .

rpm - 200 gpm

T O R Q

U E

6 1/2"/6 3/4"S3 6.5"/6.75" 7-8 2 STAGE (65S-3)

S P E E D

r p m


T O R Q U E

f t l b .

rpm - 350 gpm

rpm - 500 gpm


Volume(gpm)

Speed(rpm)

Torque(ft-lb)

hp

200 23-31 5,300 23.2

350 45-53 4,600 39.4

500 68-76 3,750 48.6

Stator Configuration 6 1/2"-6 3/4" S3 6.5"-6.75" 7-8, 2 Stage


Volume 200-500 gpm 757-1,893 lpm

Speed 23-76 rpm






Hole Size 8 3/4" - 9 7/8" 222-251 mm



Bearing Load dynam ic=130,000 lb 57.825 daN




Max. Overpull

(for re-runs)


200,250 lb 89,070 daN

8/20/2019 BlkMax


30

60

90

120

150

180

210

240

1 0 0

2 0 0

3 0 0

4 0 0

5 0 0

6 0 0

7 0 0

8 0 0

750

1,500

2,250

3,000

3,750

4,500

5,250

6,000

M A X

. D I F F .

rpm - 300 gpm

T O

R Q U E

rpm - 450 gpm

rpm - 600 gpm

6 1/2"/6 3/4" S3 6.50"/6.75" 7-8 3 STAGE (65S-4)

S P E E D

r p m


T O R Q U E

f t l b .

Volume(gpm)

Speed(rpm)

Torque(ft-lb)

hp

300 63-80 4,200 50.4

450 105-122 3,770 75.4

600 146-163 3,300 91.8

Stator Configuration


Volume 300-600 gpm ,136-2,271 lpm

Speed 63-163 rpm






Hole Size 8 3/4" - 9 7/8" 222-251 mm







Max. Overpull

(for re-runs)


200,250 lb 89,070 daN

6 1/2"-6 3/4" S3 6.5"-6.75" 7-8 3 Stage

8/20/2019 BlkMax


8/20/2019 BlkMax


PERFORMANCE

8/20/2019 BlkMax


50

100

150

200

250

300

350

400

1 5 0

3 0 0

4 5 0

6 0 0

7 5 0

9 0 0

1 , 0 5 0

1 , 2 0 0

750

1,500

2,250

3,000

3,750

4,500

5,250

6,000

M A X . D I F .

rpm - 300 gpm

T O R S I O N

6 1/2"/6 3/4"S3 6.75" 4-5 7 STAGE (675-6)

S P E E D

r p m


T O R Q U E f t - l b .

rpm - 450 gpm

rpm - 600 gpm

Stator Configuration 6 1/2"-6 3/4" S3 6.75" 4-5, 7 Stage


Volume 300-600 gpm ,136-2,271 lpm

Speed 109-295 rpm






Hole Size 7 7/8" - 9 7/8" 200-251 m m







Max. Overpull

(for re-runs)

Ab so lu te Ov erpu ll 275,000 lb 122,320 daN

234,000 lb 104,085 daN

V o l u m e( g p m )

S p e e d( r p m )

T o r q u e(f t - lb)

h p

3 0 0 1 0 9 - 1 5 0 4 , 1 0 0 8 5 .1

4 5 0 1 7 9 - 2 2 1 4 , 0 5 0 1 3 8 .0

6 0 0 2 5 4 - 2 9 5 3 , 9 0 0 1 8 8 .6

8/20/2019 BlkMax


50

100

150

200

250

300

350

400

100

200

300

400

500

600

700

800

500

1,000

1,500

2,000

2,500

3,000

3,500

4,000

MAX

.DIFF.

rpm - 300 gpm

rpm - 450 gpm

rpm - 600 gpm

T O R Q U E

6 3/4" 6.75" 4-5 4.8 STAGE (675-1)

SPEED

rpm


TORQUE

ftlb.



Volume 300-600 gpm 1,136-2,271 lpm

Speed 115-292 rpm






Hole Size 8 3/4" - 9 7/8" 222-251 mm







Max. Overpull

(for re-runs)

Abs olu te O verpul l 275,000 lb 122,320 daN

234,000 lb 104,085 daN

Volume(gpm)

Speed(rpm)

Torque(ft-lb)

hp

300 115-147 2,710 59.4

450 185-217 2,625 92.5

600 260-292 2,550 126.3

8/20/2019 BlkMax


8/20/2019 BlkMax


30

60

90

120

150

180

210

240

100

200

300

400

500

600

700

800

750

1,500

2,250

3,000

3,750

4,500

5,250

6,000

MA

X.DIFF.

rpm - 300 gpm

T O

R Q U E

rpm - 450 gpm

rpm - 600 gpm

6 3/4" 6.75" 7-8 3 STAGE (675-5)

SP

EED

rpm


TORQUE

ftlb.

Volume(gpm)

Speed(rpm)

Torque(ft-lb)

hp

300 63-80 4,200 50.4

450 105-122 3,770 75.4

600 146-163 3,300 91.8



Volume 300-600 gpm 1,136-2,271 lpm

Speed 63-163 rpm






Hole Size 8 3/4" - 9 7/8" 222-251 m m







Max. Overpull

(for re-runs)


234,000 lb 104,085 daN

8/20/2019 BlkMax


40

80

120

160

200

240

280

320

100

200

300

400

500

600

700

800

1,000

2,000

3,000

4,000

5,000

6,000

7,000

8,000

MA

X.DIFF.

rpm - 400 gpm

T O R

Q U E

7 1/2" 7.50" 4-5 3.6 STAGE (750-1)

SPEED

rpm


TORQU

E

ftlb.

rpm - 700 gpm

rpm - 900 gpm

Volume(gpm)

Speed(rpm)

Torque(ft-lb)

hp

400 74-98 4,000 56.4

700 145-168 3,750 103.6

900 195-219 3,600 133.7



Volume 400-900 gpm 1,514-3,407 lpm

Speed 72-225 rpm






Hole Size 9 5/8" - 12 1/4" 245-311 mm

Top Connection 5 1/2 Reg., 6 5/8 Reg.






Max. Overpull

(for re-runs)


310,400 lb 138,065 daN

8/20/2019 BlkMax


25

50

75

100

125

150

175

200

100

200

300

400

500

600

700

800

1,500

3,000

4,500

6,000

7,500

9,000

10,500

12,000

MA

X.DIFF.

rpm - 300 gpm

T O R Q U E

7.50" 7.50" 7-8 3 STAGE (750-2)

SPEED

rpm


TORQU

E

ftlb.

rpm - 600 gpm

rpm - 900 gpm

Volume(gpm)

Speed(rpm)

Torque(ft-lb)

hp

300 31-47 7,600 44.9

600 79-95 6,600 99.3

900 128-144 4,900 119.5



Volume 300-900 gpm 1,136-3,407 lpm

Speed 31-144 rpm






Hole Size 9 5/8" - 12 1/4" 245-311 m m

Top Connection 5 1/2 Reg., 6 5/8 Reg.Bottom Connection 6 5/8 Reg.





Max. Overpull

(for re-runs)


310,400 lb 138,065 daN

8/20/2019 BlkMax


100

200

300

400

500

600

700

800

1 0 0

2 0 0

3 0 0

4 0 0

5 0 0

6 0 0

7 0 0

8 0 0

400

800

1,200

1,600

2,000

2,400

2,800

3,200

M A

X . D I F F .

rpm - 300 gpm

T O R

Q U E

8" S3 8.00" 1-2 4 STAGE (80S-1)

S P E E D

r p m


T O R Q U E

f t l b .

rpm - 450 gpm

rpm - 600 gpm

Volume(gpm)

Speed(rpm)

Torque(ft-lb)

hp

300 160-210 1,650 50.3

450 265-320 1,650 83.3

600 375-420 1,650 117.9


Bearing Assem b ly 8" 203 m m

Volume 300-600 gpm 1,136-2,271 lpm

Speed 160-420 rpm


Max. Pressure Drop 1,500 ps i 10,342 kPa

Max. Diff. Pressure 495 ps i 3 ,413 kPa

Bit to Bend L ength 81" 2,057 m m


Hole Size 9 5/8" - 12 1/4" 245-311 m m

Top Connect ion 5 1/2 Reg., 6 5 /8 Reg.Bottom Connect ion 6 5/8 Reg.





Max. Overpul l

(for re-runs)

Abso lu te Overp ul l 406,000 lb 180,590 daN

335,200 lb 149,100 daN

8/20/2019 BlkMax


40

80

120

160

200

240

280

320

1 0 0

2 0 0

3 0 0

4 0 0

5 0 0

6 0 0

7 0 0

8 0 0

1,000

2,000

3,000

4,000

5,000

6,000

7,000

8,000

M A

X . D I F F .

rpm - 400 gpm

T O R

Q U E

8" S3 8.00" 4-5 3.6 STAGE (80S-2)

S P E E D

r p m


T O R Q U E

f t l b .

rpm - 700 gpm

rpm - 900 gpm

Volume(gpm)

Speed(rpm)

Torque(ft-lb)

hp

400 74-98 4,000 56.4

700 145-168 3,750 103.6

900 195-219 3,600 133.7

Stator Configuration 8" S3 8" 4-5, 3.6 Stage


Volume 400-900 gpm 1,514-3,407 lpm

Speed 74-219 rpm






Hole Size 9 5/8" - 12 1/4" 245-311 m m

Top Connection 5 1/2 Reg., 6 5/8 Reg.Bottom Connec t ion 6 5/8 Reg.





Max. Overpull

(for re-runs)


335,200 lb 149,100 daN

8/20/2019 BlkMax


25

50

75

100

125

150

175

200

1 0 0

2 0 0

3 0 0

4 0 0

5 0 0

6 0 0

7 0 0

8 0 0

1,500

3,000

4,500

6,000

7,500

9,000

10,500

12,000

M A

X . D I F F .

rpm - 300 gpm

T O

R Q U E

8" S3 8.00" 7-8 3 STAGE (80S-3)

S P E E D

r p m


T O R Q U E

f t l b .

rpm - 600 gpm

rpm - 900 gpm

Volume(gpm)

Speed(rpm)

Torque(ft-lb)

hp

300 30-47 7,600 43.4

600 79-95 6,600 99.3

900 128-143 4,900 119.5



Volume 300-900 gpm 1,136-3,407 lpm

Speed 30-143 rpm






Hole Size 9 5/8" - 12 1/4" 245-311 m m






Max. Overpul l

(for re-runs)


335,200 lb 149,100 daN

8/20/2019 BlkMax


30

60

90

120

150

180

210

240

1 0 0

2 0 0

3 0 0

4 0 0

5 0 0

6 0 0

7 0 0

8 0 0

1,000

2,000

3,000

4,000

5,000

6,000

7,000

8,000

M A X . D I F F .

rpm - 400 gpm

rpm - 650 gpm

rpm - 900 gpm

T O R Q U E

8" S3 8.00" 8-9 4 STAGE (80S-4)

S P E E D

r p m


T O R Q U E

f t l b .

Volume(gpm)

Speed(rpm)

Torque(ft-lb)

hp

400 90-115 6,025 103.3

650 145-170 5,570 153.8

900 199-225 4,790 181.6



Volume 400-900 gpm 1,514-3,407 lpm

Speed 90-225 rpm






Hole Size 9 5/8" - 12 1/4" 245-311 m m



(compression) static=670,375 lb 298,185daN



Max. Overpul l

(for re-runs)


335,200 lb 149,100 daN

8/20/2019 BlkMax


25

50

75

100

125

150

175

200

100

200

300

400

500

600

700

800

1,500

3,000

4,500

6,000

7,500

9,000

10,500

12,000

MAX.DIFF.

rpm - 300 gpm

T O R Q U E

8" 8.00" 6-7 4 STAGE (8S3-1)

SPEED

rpm


TORQUE

ftlb.

rpm - 600 gpm

rpm - 900 gpm

Volume(gpm)

Speed(rpm)

Torque(ft-lb)

hp

300 32-51 8,500 51.8

600 83-102 7,630 120.6

900 134-155 6,560 167.4


Bearing Assembly 8 " 203 mm

Volume 300-900 gpm 1,136-3,407 lpm

Speed 32-155 rpm





O/A Length 332" 8433 mm

Hole Size 9 5/8" - 12 1/4" 244-311 mm

Top Connect ion 5 1/2 Reg., - 6 5/8 Reg.

Bottom Conenct ion 6 5/8 Reg.





Max. Overpull

(for re-runs)


101,400 lb 45,105 daN

8/20/2019 BlkMax


15

30

45

60

75

90

105

120

5 0

1 0 0

1 5 0

2 0 0

2 5 0

3 0 0

3 5 0

4 0 0

1,250

2,500

3,750

5,000

6,250

7,500

8,750

9,000

M A

X . D I F F .

rpm - 400 gpm

T O R Q U E

8" S3 AIR 8.00" 7-8 2 STG (80S-5)

S P E E D

r p m


T O R Q U E

f t l b .

rpm - 550 gpm

rpm - 800 gpm



Bearing Assembly 8 " 203 mm

Volume 400-800 gpm 1,514 - 3,028 lpm

Speed 33-86 rpm






Hole Size 9 5/8" - 12 1/4" 244 - 311 mm

Top Connection 5 1/2 Reg., - 6 5/8 Reg.


Bearing Load 104,930 daN

(compression) 112,770 daN

Bearing Load 41,970 daN

(tension) 45,105 daN

Max. Overpull

(for re-runs)

Abso lute Over pull 257,985 daN

dynamic=235,900 lb

static=253,525 lb

dynamic=94,350 lb

static=101,400 lb

580,000 lb

101,400 lb 45,105 daN

Volume(gpm)

Speed(rpm)

Torque(ft-lb)

hp

400 33 - 43 7,060 44.4

550 49 - 59 6,300 58.8

800 76 - 86 4,133 59.8

8/20/2019 BlkMax


100

200

300

400

500

600

700

800

150

300

450

600

750

900

1,050

1,200

1,000

2,000

3,000

4,000

5,000

6,000

7,000

8,000

MA

X.DIFF.

rpm - 600 gpm

T O R Q

U E

rpm - 900 gpm

rpm - 1,200 gpm

9 5/8" 9.62" 2-3 7.5 STAGE (962-1)

SPE

ED

rpm


TORQUE

ftlb.

Volume(gpm)

Speed(rpm)

Torque(ft-lb)

hp

600 218-281 4,500 186.8

900 358-421 4,450 303.3

1,200 498-561 4,420 419.1

Stator Configuration 9 5/8" S3 9.62" 2-3 7.5 Stage


Volume 600-1,200 gpm 2,271-4,542 lpm

Speed 218-561 rpm






Hole Size 12 1/4" - 17 1/2" 311-445 mm

Top Connection 6 5/8 Reg., 7 5/8 Reg.Bottom Connection 6 5/8 Reg., 7 5/8 Reg.





Max. Overpull

(for re-runs)


101,400 lb 45,105 daN

8/20/2019 BlkMax


40

80

120

160

200

240

280

320

100

200

300

400

500

600

700

800

1,500

3,000

4,500

6,000

7,500

9,000

10,500

12,000

MA

X.DIFF.

rpm - 600 gpm

T O R Q

U E

rpm - 900 gpm

rpm - 1,200 gpm

9 5/8" 9.62" 3-4 4.5 STAGE (962-2)

SPE

ED

rpm


TORQUE

ftlb.

Volume(gpm)

Speed(rpm)

Torque(ft-lb)

hp

600 97-132 6,245 115.4

900 165-200 6,000 188.6

1,200 234-269 5,620 250.5

Stator Configuration 9 5/8" S3 9.62" 3-4, 4.5 Stage


Volume 600-1,200 gpm 2,271-4,542 lpm

Speed 97-269 rpm






Hole Size 12 1/4" - 17 1/2" 311-445 mm






Max. Overpull

(for re-runs)


101,400 lb 45,105 daN

8/20/2019 BlkMax


40

80

120

160

200

240

280

320

100

200

300

400

500

600

700

800

1,000

2,000

3,000

4,000

5,000

6,000

7,000

8,000

MA

X.DIFF.

rpm - 600 gpm

T O R Q U E

9 5/8" 9.62" 3-4 6 STAGE (962-7)

SPEED

RPM


TORQUE

ftlb.rpm - 900 gpm

rpm - 1,200 gpm

Volume(gpm)

Speed(rpm)

Torque(ft-lb)

hp

600 99-129 7,200 135.7

900 164-194 7,120 222.3

1,200 227-257 7,000 302.6



Volume 600-1200 gpm 2,271-4,543 lpm

Speed 99-257 rpm






Hole Size 12 1/4" - 17 1/2" 311-445 mm






Max. Overpull

(for re-runs)


101,400 lb 45,105 daN

8/20/2019 BlkMax


25

50

75

100

125

150

175

200

100

200

300

400

500

600

700

800

1,500

3,000

4,500

6,000

7,500

9,000

10,500

12,000

MAX.DIFF.

rpm - 300 gpm

T O R Q U E

9 5/8" 9.62" 4-5 4 STAGE (962-3)

SPEED

rpm


TORQUE

ftlb.

rpm - 600 gpm

rpm - 900 gpm

Volume(gpm)

Speed(rpm)

Torque(ft-lb)

hp

300 52-68 8,000 79.2

600 110-125 7,500 157.1

900 168-185 6,510 208.2



Volume 300-900 gpm 1,136-3,407 lpm

Speed 52-185 rpm






Hole Size 12 1/4" - 17 1/2" 311-445 mm






Max. Overpull

(for re-runs)


101,400 lb 45,105 daN

8/20/2019 BlkMax


25

50

75

100

125

150

175

200

75

150

225

300

375

450

525

600

2,000

4,000

6,000

8,000

10,000

12,000

14,000

16,000

MA

X.

DIFF.

rpm - 600 gpm

T O R Q

U E

rpm - 900 gpm

rpm - 1,200 gpm

9 5/8" 9.62" 5-6 3 STAGE (962-4)

SPEED

r pm


TORQUE

ftlb.



Volume 600-1,200 gpm 2,271-4,542 lpm

Speed 40-127 rpm






Hole Size 12 1/4" - 17 1/2" 311-445 mm

Top Connection 6 5/8 Reg., 7 5/8 Reg.Bottom Conenction 6 5/8 Reg., 7 5/8 Reg.





Max. Overpull

(for re-runs)


101,400 lb 45,105 daN

Volume(gpm)

Speed(rpm)

Torque(ft-lb)

hp

600 40-62 8,830 67.3

900 74-96 8,025 113.1

1,200 105-127 7,525 150.5

8/20/2019 BlkMax


25

50

75

100

125

150

175

200

100

200

300

400

500

600

700

800

1,500

3,000

4,500

6,000

7,500

9,000

10,500

12,000

MAX.DIFF.

rpm - 300 gpm

T O R Q

U E

9 5/8" 8.00" 6-7 4 STAGE (962-5)

SPEED

rpm


TORQUE

ftl b

.

rpm - 600 gpm

rpm - 900 gpm

Volume(gpm)

Speed(rpm)

Torque(ft-lb)

hp

300 32-51 8,500 51.8

600 83-102 7,630 120.6

900 134-155 6,560 167.4



Volume 300-900 gpm 1,136-3,407 lpm

Speed 32-155 rpm






Hole Size 12 1/4" - 17 1/2" 311-445 mm

Top Connection 6 5/8 Reg., 7 5/8 Reg.Bottom Conenction 6 5/8 Reg., 7 5/8 Reg.





Max. Overpull

(for re-runs)


101,400 lb 45,105 daN

8/20/2019 BlkMax


8/20/2019 BlkMax


100

200

300

400

500

600

700

800

150

300

450

600

750

900

1,050

1,200

1,000

2,000

3,000

4,000

5,000

6,000

7,000

8,000

MAX.DIFF.

rpm - 600 gpm

T O R Q

U E

rpm - 900 gpm

rpm - 1,200 gpm

9 5/8" 9.62" 2-3 7.5 STAGE (962-1)

SPE

ED

rpm


TORQUE

ftlb.

Volume(gpm)

Speed(rpm)

Torque(ft-lb)

hp

600 218-281 4,500 186.8

900 358-421 4,450 303.3

1,200 498-561 4,420 419.1



Volume 600-1,200 gpm 2,271-4,542 lpm

Speed 218-561 rpm






Hole Size 12 1/4" - 17 1/2" 311-445 mm






Max. Overpull

(for re-runs)


101,400 lb 45,105 daN

8/20/2019 BlkMax


40

80

120

160

200

240

280

320

100

200

300

400

500

600

700

800

1,500

3,000

4,500

6,000

7,500

9,000

10,500

12,000

MAX.DIFF.

rpm - 600 gpm

T O R Q

U E

rpm - 900 gpm

rpm - 1,200 gpm

9 5/8" 9.62" 3-4 4.5 STAGE (962-2)

SPE

ED

rpm


TORQUE

ftlb.

Volume(gpm)

Speed(rpm)

Torque(ft-lb)

hp

600 97-132 6,245 115.4

900 165-200 6,000 188.6

1,200 234-269 5,620 250.5



Volume 600-1,200 gpm 2,271-4,542 lpm

Speed 97-269 rpm






Hole Size 12 1/4" - 17 1/2" 311-445 mm






Max. Overpull

(for re-runs)


101,400 lb 45,105 daN

8/20/2019 BlkMax


40

80

120

160

200

240

280

320

100

200

300

400

500

600

700

800

1,000

2,000

3,000

4,000

5,000

6,000

7,000

8,000

MAX.DIFF.

rpm - 600 gpm

T O R Q U E

9 5/8" 9.62" 3-4 6 STAGE (962-7)

SPEED

RPM


TORQUE

ftlb.rpm - 900 gpm

rpm - 1,200 gpm

Volume(gpm)

Speed(rpm)

Torque(ft-lb)

hp

600 99-129 7,200 135.7

900 164-194 7,120 222.3

1,200 227-257 7,000 302.6



Volume 600-1200 gpm 2,271-4,543 lpm

Speed 99-257 rpm






Hole Size 12 1/4" - 17 1/2" 311-445 mm






Max. Overpull

(for re-runs)

Absolu te Overpu ll 580,000 lb 257,985 daN

101,400 lb 45,105 daN

8/20/2019 BlkMax


25

50

75

100

125

150

175

200

100

200

300

400

500

600

700

800

1,500

3,000

4,500

6,000

7,500

9,000

10,500

12,000

MAX.D

IFF.

rpm - 300 gpm

T O R Q U E

9 5/8" 9.62" 4-5 4 STAGE (962-3)

SPEED

rpm


TORQUE

f tlb.

rpm - 600 gpm

rpm - 900 gpm

Volume(gpm)

Speed(rpm)

Torque(ft-lb)

hp

300 52-68 8,000 79.2

600 110-125 7,500 157.1

900 168-185 6,510 208.2



Volume 300-900 gpm 1,136-3,407 lpm

Speed 52-185 rpm






Hole Size 12 1/4" - 17 1/2" 311-445 mm






Max. Overpull

(for re-runs)


101,400 lb 45,105 daN

8/20/2019 BlkMax


25

50

75

100

125

150

175

200

75

150

225

300

375

450

525

600

2,000

4,000

6,000

8,000

10,000

12,000

14,000

16,000

MAX.

DIFF.

rpm - 600 gpm

T O R Q

U E

rpm - 900 gpm

rpm - 1,200 gpm

9 5/8" 9.62" 5-6 3 STAGE (962-4)

SPEED

r pm


TORQUE

ftlb.



Volume 600-1,200 gpm 2,271-4,542 lpm

Speed 40-127 rpm






Hole Size 12 1/4" - 17 1/2" 311-445 mm

Top Connection6 5/8 Reg., 7 5/8 Reg.

Bottom Conenction 6 5/8 Reg., 7 5/8 Reg.





Max. Overpull

(for re-runs)


101,400 lb 45,105 daN

Volume(gpm)

Speed(rpm)

Torque(ft-lb)

hp

600 40-62 8,830 67.3

900 74-96 8,025 113.1

1,200 105-127 7,525 150.5

PERFORMANCE

8/20/2019 BlkMax


25

50

75

100

125

150

175

200

100

200

300

400

500

600

700

800

1,500

3,000

4,500

6,000

7,500

9,000

10,500

12,000

M

AX.DIFF.

rpm - 300 gpm

T

O R Q

U E

9 5/8" 8.00" 6-7 4 STAGE (962-5)

SPEED

rpm


TORQUE

ftl b

.

rpm - 600 gpm

rpm - 900 gpm

Volume(gpm)

Speed(rpm)

Torque(ft-lb)

hp

300 32-51 8,500 51.8

600 83-102 7,630 120.6

900 134-155 6,560 167.4



Volume 300-900 gpm 1,136-3,407 lpm

Speed 32-155 rpm






Hole Size 12 1/4" - 17 1/2" 311-445 mm







Max. Overpull

(for re-runs)


101,400 lb 45,105 daN

PERFORMANCE

8/20/2019 BlkMax


25

50

75

100

125

150

175

200

100

200

300

400

500

600

70

0

800

2,000

4,000

6,000

8,000

10,000

12,000

14,000

16,000

MAX.DIFF.

rpm - 600 gpm

T O R Q

U E

9 5/8" 9.62" 6-7 5 STAGE (962-6)

SPEED

RPM


TORQUE

ftlb.

rpm - 900 gpm

rpm - 1,200 gpm

Volume(gpm)

Speed(rpm)

Torque(ft-lb)

hp

600 48-76 13,300 121.6

900 86-113 12,780 209.3

1,200 124-149 12,000 283.3

Stator Configuration 9 5/8" 9.62" 6-7 5 Stage


Volume 600-1,200 gpm 2,271-4,542 lpm

Speed 48-149 rpm






Hole Size 12 1/4" - 17 1/2" 311-445 mm







Max. Overpull

(for re-runs)


101,400 lb 45,105 daN

8/20/2019 BlkMax


30

60

90

120

150

180

210

240

1 0 0

2 0 0

3 0 0

4 0 0

5 0 0

6 0 0

7 0 0

8 0 0

2,000

4,000

6,000

8,000

10,000

12,000

14,000

16,000

M A X . D I F F .

rpm - 900 gpm

T O R Q

U E

11 1/4" 11.25" 3-4 3.6 STAGE (1125-1)

S P E E D

r p m


T O R Q U E

f t l b

rpm - 1200 gpm

rpm - 1500 gpm



Volume 900-1,500 gpm 3,406-5,678 lpm

Speed 81-168 rpm






Hole Size 12 1/4" - 17 1/2" 311-445 lpm



Bearing Load dynamic=1,000,000 lb 444,800 daN

(compression) static=1,000,000 lb 444,800 daN



Max. Overpull

(for re-runs)

Abs olu te Overpu ll 1,000,000 lb 444,800 daN

500,000 lb 222,400 daN

Volume(gpm)

Speed(rpm)

Torque(ft-lb)

hp

900 81-100 8,700 134.2

1,200 114-133 8,570 186.0

1,500 149-168 8,350 236.9

SHIPPING INFORMATION

L e n g t h W e ig h t

8/20/2019 BlkMax


TABLE FOR SHIPPING PURPOSES ONLY

f t m lb k g

1 1 1 / 1 6 1 0 . 4 3 . 2 4 0 1 8

2 1 / 1 6 9 . 3 2 . 8 5 0 2 3

2 3 / 8 1 3 . 6 4 . 1 1 5 0 6 8

2 7 / 8 1 7 . 3 5 . 3 2 7 5 1 2 5

3 1 / 8 1 5 . 3 4 . 7 3 0 0 1 3 6

3 3 / 8 2 3 . 5 7 . 2 5 0 0 2 2 7

3 3 / 4 1 8 . 8 5 . 7 5 0 0 2 2 7

4 3 / 4 S h o r t 2 0 . 5 6 . 2 9 0 0 4 0 8

5 S 3 2 5 . 3 7 . 7 1 1 0 0 4 9 9

5 2 7 . 0 8 . 2 1 1 0 0 4 9 9

5 1 / 2 2 2 . 8 6 . 9 1 3 0 0 5 9 0

6 1 / 2 3 1 . 4 9 . 6 2 0 0 0 9 0 7

6 1 / 2 S 3 3 0 . 0 9 . 1 2 0 0 0 9 0 7

6 3 / 4 3 1 . 4 9 . 6 2 0 0 0 9 0 7

7 1 / 2 2 6 . 0 7 . 9 3 5 0 0 1 5 8 8

8 2 9 . 0 8 . 8 3 8 0 0 1 7 2 4

8 S 3 2 9 . 0 8 . 8 3 8 0 0 1 7 2 4

9 5 / 8 S 3 3 1 . 2 9 . 5 5 6 0 0 2 5 4 0

9 5 / 8 3 1 . 4 9 . 6 5 6 0 0 2 5 4 0

1 1 1 / 4 3 4 . 0 1 0 . 4 6 5 0 0 2 9 4 8

L e n g t h W e ig h t

M o t o r S iz e

Ray-Son Product Line

8/20/2019 BlkMax


Black Max provides its customers with both mechanical and hydraulic/mechanical jars.They range in size from a 1 11/16” mechanical jar to an 8” hydraulic/mechanic jar.Black Max jars are designed to create powerful up or down forces that will ‘jar’ thestring that has become stuck during drilling operation. The jars are manufactured of high strength alloy steel, they are oil lubricated and completely sealed and aredesigned to operate in the harshest of drilling conditions.The hydraulic/mechanical jars consist of a mechanical latch that keeps the jar in theneutral position and prevents unexpected jarring when tripping in or out of the hole.The jars also consist of a hydraulic section that creates a time delay when the jar is in

operation and the latch is disengaged.Black Max’s two way hydraulic/mechanical jars are versatile and easy to use. Tooperate the jars simply apply tension or compression to the running string. Varying thetension or compression loads during the hydraulic time delay controls the intensity of the jar impact. When a push or pull action is applied to the jar, hydraulic oil is forcedaround a restricting valve. This restriction of oil flow from one chamber to the other delays the stroke. This delay enables the running string to stretch before the jar fires.

Black Max provides its customers with a full range of Ray-Son shock tool sizes, from 3½” to 11”.Ray-Son shock tools are designed to cushion heavy axial loading and reduce bitvibration encountered during drilling operations.

The shock tools’ springs consist of belleville spring elements made from heat-treatedsteel. All shock tool internals are sealed completely from drilling fluids and the internalsare oil lubricated.

8/20/2019 BlkMax


are oil lubricated.Black Max shock tools are sprung both ways (tension and compression) toaccommodate loading from both directions and are pressure balanced from extremehydrostatic pressures, maximizing the performance of the shock tools. The shock toolshave two types of mandrels so that they can be placed in the string or in the bottomhole locations.These shock tools are cost effective. They maximize bit life as they provide consistentrates of penetration and minimize harmonics created in the drilling string while drilling.Placing the shock tool in an appropriate location in the string will extend drilling stringtubular life, reduce repair costs on thread connections, and extend the life of the tool.

SHOCK TOOL

8/20/2019 BlkMax


1 350 475 625 675 775 800 900 950 1100 3 350 475 625 675 775 800 900 950 1100

A 3. 53 4. 81 6. 31 6. 81 7.8 8. 12 9. 06 9. 56 11 A 3. 53 4. 81 6.3 6. 81 7.8 8. 12 9. 06 9.56 11

B 2.62 3.5 4.5 4.88 5.5 5.5 6.75 7.25 8 B 3 .03 3.9 5.04 5.52 6.08 6.08 7.49 7.99 9

C 2.5 3.37 4.43 4.75 5.25 5.25 6.45 7 7.63 C 2 .88 3.37 4.26 4.88 5.26 5.3 6.6 7.99 9

D 1.75 2.38 3 3.25 3.75 3.75 4.81 4.81 5.38 D 3 .03 3.9 3.5 5.52 6.08 6.08 7.25 7.99 9

E 1.64 2.26 2.85 2.97 3.56 3.56 4.56 4.56 5.25 E 2.25 20.5 20.43 32.2 24 30 35.33 4 4

F 1 1.5 2 2.25 2.5 2 .5 3 2 .81 2.88 F 12 8.2 9.07 6.55 7 .01 16.75 6.5 27.33 37

G 11 17.4 20.5 19.7 14.88 19 18.5 18.5 23.9 G 2.25 6.5 8.5 9 10.74 5 14.5 4 4

H 6 8.1 5.3 8.1 10.62 11 13.67 13.67 14.5

J 10.87 15.6 13.2 18.5 21 21 24.5 29 30 4 350 475 625 675 775 800 900 950 1100

K 12.13 16 16.5 26.7 15 21 20.83 20.83 31.6 A 2.37 3.36 4.25 4.87 5.25 5.24 6 6.25 7.25

B 1 1.5 2 2.25 2.5 2.5 3 2.81 2.88

2 350 475 625 675 775 800 900 950 1100 C 1.88 2.88 3 4 4.88 4.88 5.18 5.18 5.38

A 2. 64 3. 51 4. 51 4.9 5. 52 5. 52 6. 77 7. 29 8. 02 D 2 5. 89 4.5 7. 75 9. 32 6.6 5.7 5.7 6.4

B 3.53 4.81 6.31 6.81 7.8 8.12 9 .06 9 .56 11 E 2 1 .3 2 2 1 .93 1.4 2.3 2.3 2 .98

C 2.75 3.63 4.75 5.38 6 6 7 7.5 9

D 2.24 2.77 3.51 4.34 4.73 4.73 5.85 6.4 6.8 5 350 475 625 675 775 800 900 950 1100

E 3 4.4 3.3 5 6.9 6.9 5.38 5.38 7 A 2.5 3 3.5 4.5 4 2.5 6.6 6.77 7.75

F 3.75 3.9 2.5 3.3 4.97 4.97 7.75 8.62 9.5 B 3.53 4.81 6.31 6.81 7.8 8.12 9.06 9.56 11

G 5.75 8.86 7.2 11.2 9.75 9.75 11.63 15.25 14.2 C 1.5 3 2 3.5 4 2.5 4.93 5.43 4.88

D 5.84 3.5 6 6 4.5 4.5 14 14 15.17

E 5 .16 10.5 12 12 7.5 10.5 12 8 11.53

MECHANICAL JAR

8/20/2019 BlkMax


1 1 6 8 4 7 5 6 2 5 6 7 5 4 1 6 8 4 7 5 6 2 5 6 7 5

A 1 . 6 9 4 .8 6 . 2 8 6 .6 A 1 .6 9 4 .8 6 . 2 5 6 .6

B 1 . 1 9 3 .5 4 . 6 3 4 . 7 5 B 1 .3 2 3 . 8 9 5 . 0 4 5 .3 8

C 1 . 0 8 3 .4 4 . 4 6 4 . 6 8 C 0 .9 3 .2 3 . 7 5 4 .0 5

D 0. 31 2 2.25 2 .5 D 1 0 . 5 5 2 0 . 5 2 4 2 4 . 5

. . . . . . .

F 1 4 .3 1 8 .4 1 7 . 6 2 1 9 .6

G 1 6 .9 2 2 . 7 5 2 3 .5 2 2 . 5 9 5 1 6 8 4 7 5 6 2 5 6 7 5

H 1 . 2 5 3 . 2 5 4 . 8 8 4 . 8 1 A 1 .6 9 4 .8 6 . 2 5 6 .6

B 1 .1 9 3 . 8 9 4 . 6 3 4 .7 6

2 1 6 8 4 7 5 6 2 5 6 7 5 C 1 .1 9 3 .5 4 . 7 5 5

A 1 . 1 9 3 . 5 1 4 . 6 4 4 . 7 6 D 1 .1 9 2 3 3 .7 5

B 1 . 6 9 4 .8 6 . 2 5 6 .6 E 1 9 .2 7 6 .8 1 5 . 2 5 1 5 .3 7

C 1 . 2 5 3 . 7 5 5 . 2 5 5 . 2 5 F - 1 6 .4 5 . 7 5 5 .6 3

D 0 . 8 8 3 . 0 7 3 . 9 8 4 . 0 9 G - 2 .1 1 4 1 5 .0 1

E 1 . 6 1 4. 7 5 5. 7 5 6 .5 H - 1 0 .7 1 2 9 .6 5

. . .

G 3 .4 1 0 . 7 5 1 0 . 7 5 1 0 . 7 5 6 1 6 8 4 7 5 6 2 5 6 7 5

A 1 .3 3 . 8 7 5 . 0 2 5 .3 8

3 1 6 8 4 7 5 6 2 5 6 7 5 B 0 .7 7 3 3 .5 3 .7 5

A 1 . 6 9 4 .8 6 . 2 5 6 .6 C 0 .3 1 2 2 . 2 5 2 .5

B 1 . 3 2 3 . 8 9 5 . 0 4 5 . 3 8 D 1 .5 4 .5 6 .5 6 .5

C 0 .9 3 .2 3 . 7 7 4 . 0 5 E 2 6 .7 4 2 4 8 4 8

D 1 4 .8 2 0 2 2 .5 2 2 .5

E 1 .7 4 .5 6 5 .5 7 1 6 8 4 7 5 6 2 5 6 7 5

A 1 .1 8 3 . 4 9 4 . 6 1 4 .7 5

B 0 .3 1 2 2. 2 5 2 .5

. .

HYDRAULIC/MECHANICAL JAR

8/20/2019 BlkMax


1 350 475 650 800

A 3.53 4.8 6.6 8.12

B 2.62 3.5 4.75 5.5

C 2.5 3.4 4.69 5.25

D 1.13 2 2.75 3

E 8.9 10.6 20 19.14

F 20.15 27.24 25.75 27.61

G 24.65 34.84 31.69 31

H 2.14 3.25 4.81 4.38

2 350 475 650 800

A 3.53 4.8 6.6 8.12

B 2.88 3.75 5.25 6

C 2.24 3.07 4.27 4.73

D 2.64 3.51 4.76 5.52

E 3.2 4.75 5.75 6.85

F 16.3 21 20.5 21.64

G 5.75 10.75 10.75 9.75

3 350 475 650 800

A 3.53 4.8 6.6 8.12

B 2.88 3.89 5.38 6.08

C 2.25 3.2 4 4.5

D 20.5 28 30.5 30.5

E 2.5 4.5 5.5 6

4 350 475 650 800

A 2.86 3.8 5.38 6.04

B 2 3 3.69 4.25

C 1.13 2 2.75 3

D 2.5 4.5 6.5 6

E 43 49.5 55.5 60.25

5 350 475 650 800

A 3.53 4.8 6.6 8.12

B 2.63 3.5 4.75 5.5

C 2 2.75 4 4.5

D 24.25 32.12 34.5 36

E 2.5 4.5 5.5 6

6 350 475 650 800

A 2.59 3.48 4.73 5.48

B 1.88 2.63 3.63 4.13

C 1.75 2.44 3.38 3.88

D 1.13 2 2.75 3

E 2.5 5.5 7.3 6.5

F 23.2 29.75 30.86 31.49

G 7.05 8.4 8.74 8.76

7 350 475 650 800

A 3.53 4.8 6.6 8.12

B 2.77 3.69 5.14 5.75C 30.7 39.3 40.5 41.5

8 350 475 650 800

A 2.4 3.25 4.5 4.88B 1.88 2.63 3.63 4.13

C 1.13 2 2.75 3

D 2.5 3 3 3

E 19.5 25 26.25 27

9 350 475 650 800

A 3.53 4.8 6.6 8.12

B 2.89 3.5 4.75 5.5

C 2 2.75 4 4.5

D 18.75 19.5 19.5 21

E 2.5 4.5 5.5 6

10 350 475 650 800

A 3.53 4.8 6.6 8.12

B 1.9 3.2 4.5 5

C 1.13 2 2.75 3

D 4 4.8 5.4 5.5

E 7 10.2 10.6 13.5

11 350 475 650 800

A 3.53 4.8 6.6 8.12

B 2.88 3.89 5.38 6.08

C 2.25 3.2 4.05 4.5

D 20.5 20.5 24.5 26.5

E 2.5 4.5 5.5 6

MECHANICAL JARS

Tool Size (in.) 1 11/16 4 3/4 6 1/4 6 3/4

HYDRAULIC / MECHANICAL JARS

Tool Size (in) 3 1/2 4 3/4 6 1/2 8

8/20/2019 BlkMax


( )

(mm) 43 121 159 171

O.D. (in) 1.69 4.8 6.28 6.6

(mm) 43 122 160 167

I.D. (in.) 0.31 2.25 2.25 2.5

(mm) 8 51 57 64Length (ft) 6.1 10.1 12.3 12.4

(m) 1.9 3.1 3.7 3.8

Max. Latch Setting (lb) 10,000 45,000 85,000 100,000

(daN) 4,450 20,000 37,800 44,500

Max. Tensile Pull (lb) 25,000 300,000 531,000 531,000

(after jarring) (daN) 11,100 133,440 236,188 236,188

Piston Area (in.2) 1.1 9.6 16.7 17.7

(cm2) 7.2 46.2 107.7 114.3

( )

(mm) 89 121 165 203

O.D. (in) 3.53 4.8 6.6 8.12

(mm) 90 122 168 206

I.D. (in.) 1.13 2 2.75 3

(mm) 29 51 70 76Length (ft) 14 17.5 19.3 20

(m) 4.3 5.3 5.9 6.1

Max. Latch Setting (lb) 25,000 45,000 100,000 120,000

(daN) 11,100 20,000 37,800 53,350

Max. Prejar Pull (lb) 30,000 50,000 105,000 125,000

(daN) 13,350 22,250 46,700 55,600

Max. Tensile Pull (lb) 150,000 265,000 531,000 733,000

(after jarring) (daN) 66,720 117,870 236,188 326,000

Piston Area (in.2) 2.8 5.4 10.3 12.6

(cm2) 17.8 34.9 66.6 81.1

120,000

Approx. 60,000

UP

DOWN

100,000

Approx. 50,000

UP

DOWN

45,000

Approx. 22,500

UP

DOWN

25,000

Approx. 12,500

UP

DOWN

TOOL SIZE

I.D.

LENGTH (Latched)

WEIGHT

STROKE UP & DOWN(Free stroke after valve release)

MAX. PREJAR PULL (lbs)

MAX. PULL (lbs) (After jarring)

MAX. TORSIONAL LOAD (ft-lb)

PUMP OPEN AREA

8"

3.00"

20.0 ft

2500 lbs

6”

180,000

733,000

65,000

6.3 in2

6½”

2.75"

19.3 ft

1500 lbs

6”

140,000

531,000

42,000

4.4 in2

4¾”

2.25"

17.5 ft

800 lbs

1.8 in2

6”

65,000

265,000

12,000

PRESET RELEASE (lbs)

2.5 in2

3½”

1.13”

14 ft

400 lbs

6”

30,000

150,000

7,000

SHOCK TOOLS

8/20/2019 BlkMax


BEST HITTER SPECIFICATIONS

8/20/2019 BlkMax


** CONNECTIONS CAN BE MANUFACTURED TO CLIENTS' 1SPECIFICATIONS

Design Features Of The BEST HITTER Drilling Jar

1. Heat-treated and stress relieved aircraft quality SAE 4340 and 4140 steel.

2. All box and pin connections both internal and external are stress relieved.

3. Internal and external connections are torqued to manufacturer specifications,which have been proven in the field.

4. Hydrostatic pressure does not affect the BEST HITTER.

TOOL O.D. 4-3/4" 6-1/4" 7-3/4"

TOOL I.D. 2" 2-1/4" 2-3/4"

TOOL JOINT 3-1/2" API 4-1/2" API 6-5/6" REG.

**CONNECTION I.F. I.F. REG.

OVERALL LENGTH 31' 34.5' 36'

TENSILE YIELD STRENGTH 40,000 70,000 120,000

TORQUE YIELD STRENGTH 19,000 35,000 65,000

DOWN STROKE 8 8 8

UP STROKE 8 8 8

TOTAL STROKE LENGTH 16 16 16

WEIGHT IN LBS. 1400 2400 4000

OPERATING INSTRUCTIONS

8/20/2019 BlkMax


The Best Hitter mechanical drilling jar is self-cocking and will trip immediately after the required weight or pull is applied. The Best Hitter is delivered to the location inthe cocked position, with about 8" of the mandrel exposed, and will usually becocked when it is pulled out of the hole.

To run the jar in the hole, it is recommended that the jar be uncocked. Sometimes, itmay be necessary to run the jar in the cocked position, i.e. in fishing operations.

To uncock the Best Hitter jar, you need to do the following: With drill pipe or collars

to be used above the jar, set the slips on the jar body below the mandrel. Unlock therotary. The break out tongs should be placed on the jar above the mandrel and theback up tongs below the mandrel. Using a rope to pull on the break out tongs turnthe mandrel 1/8 turn to the left. Hold the 1/8 turn and pick up on the string to openthe jar. There will be 16 inches of exposed mandrel (approximately). Pull the slipsand run the jar in the hole.Note: DO NOT TURN MANDREL OVER 1/8 TURN TO THE LEFT.

JAR PLACEMENT IN THE STRING: Run three collars above the jar. With hevi-watedrill pipe at least five joints should be run above the jar.

UPWARD STROKE: Pull on string until the jar setting specified is reached and jar will trip.

8/20/2019 BlkMax


RECOCK JAR: Slack off on drill string until slightly below the weight of the stringabove the jar. The weight indicator needle should bobble when the jar completes itsfree travel and recocks.

EXAMPLES:

250.000 Total indicator weight -40.000 Bottom Hole Assembly below the jar 210.000 Weight of the string above the jar +90.000 Upstroke Setting on jar

300.000+20.000 Hole drag picking up320.000 Indicator reading to trip jar

You will probably have to slack off to about 200.000 to cock the jar for another upward hit.

DOWNWARD STROKE: Slack off on the string until the setting reached which is

required to trip the jar.

TO RECOCK FOR JARRING DOWN ONLY: Pick up pipe or string until the weightabove the jar is slightly above the weight above the jar. A slight bobble on theindicator will be noticed when the jar recocks. Free travel will also be noted.

EXAMPLE FOR DOWNWARD TRIPPING OF JAR:

250.000 Total indicator weight38 000 Weight below the jar

8/20/2019 BlkMax


-38.000 Weight below the jar 212.000 Weight below jar -36.000 Upstroke Setting on jar 176.000

-20.000 Hole drag156.000 Indicator reading necessary to trip jar downward

NOTE: The downward stroke is less noticeable than the upward stroke in mostcases. The downward tripping can only be detected by the weight indicator in mostcases especially in deep holes and when using small jars.

HEAVIER JAR TRIPPING: Apply and hold right hand torque to drill string. Apply thetorque 1/2 around at a time until the desired setting is reached. With too much righthand Torque it would not be possible to pull enough so that the jar would trip. In theevent that too much right hand Torque is applied, release the torque and the jar willreturn to the original setting.

LIGHTER JAR TRIPPING: Apply and hold left hand torque to drill string. Apply thetorque 1/2 round at a time until the desired setting is reached. With too much lefthand torque the jar will be out of jay and you will not have a jarring effect. This wouldgive you 6 inches of free travel. To correct too much left hand torque, release thetorque and the jar will return to its original setting.

TROUBLE SHOOTING JARS: When the string becomes stuck while drilling, it islikely that some right hand torque has been trapped in the string. To correct this, pickup the string to the weight of the string above the jar and apply three rounds of left-

8/20/2019 BlkMax


hand torque. Hold the torque for a few seconds and release. Repeat this procedureuntil you get three rounds back to the right. When you pick up on the string at thispoint, the jar should hit. If it does not hit, look for free travel in the string and if thereis none, then you are probably stuck above the jar.

NOTE: While going into the hole with a jar in the open position, the driller shouldensure that when he sets the slips they aren’t sitting on a ledge where the jar hastaken weight and may slip off. If this happens it is possible that the bit may roll off after you have set the slips, unlatched the elevators and gone after another stand of pipe.

This might lead you to think that the jar has gone off on its own and this should not bethe case.

Rig Rattler

Features:

8/20/2019 BlkMax


• At 15’ (4.58m) long, this jar was designed to be the shortest combination jar in theindustry.

• The “Rig Rattler” has a total of 22” of strokeBump DownFrom the closed position, 12” of free stroke is built into the jar so it can operate as abumper sub. In this regime the jar can bump down as often as desired withouthaving to fire the jar or enter its metering section.Fully extended, the “Rig Rattler” provides 22” of unrestricted bumper stroke.

Jarring UpThe “Rig Rattler” will only fire if a force greater than the customers’ required safetysetting is achieved. From that point the jar will meter 4” before providing 6” of impactstroke. The time to fire as well as jarring impact is adjusted by how much force isexerted on the jar.

• The built in safety mechanism of the jar allows worry free tripping. The “Rig Rattler”is hydrostatically balanced. It does not have any mud ports to plug up, and only has

two seal surfaces exposed to drilling mud.• Connections on downhole tools bother you? This jar has only three internalconnections.

• The internal components of the “Rig Rattler” have been specially designed toeliminate fluid restrictions inside the jar during either the up or down hitting stroke.By eliminating these restrictions the hitting power of the jar is maximized.

• The valve of the “Rig Rattler”‘, which controls the safety setting and timing of the jar, is filtered from contaminants during all modes of operation.

• Use of the “LEE Jeva” make the firing time of the “Rig Ratter” independent of

8/20/2019 BlkMax


temperature.

The “Rig Rattler” jar has been designed to be the toughest, hardest hitting jar in theindustry. As with most things, the best idea is often the simplest. This drilling jar meets this criteria. Through the ruggedness and simplicity of its design we believethat the “Rig Rattler” is the best jar on the market. It is easy to run, and costeffective to maintain. These are savings that can be passed on to our customers.

O.D. 4 3/4” 6 1/2” 6 3/4”

I.D. 2 1/4” 2 1/2” 2-1/2Maximum Pre-jar pull

70,000 lb 200,000 lb 200,000 lb

Maximum Post- jar pull

230,000 lb 585,000 lb 585,000 lb

Weight 550 lb 1000 lb 1150 lbMax Torque 12,500 ft-lb 27,000 ft-lb 42,000 ft-lb

Closed Length 12 ft 15 ft 15 ftExtended Length 13.8 ft 16.8 ft 16.8 ft

MILLINGRUN #1

Well bore preparation prior to whipstock installation:

8/20/2019 BlkMax


Well bore preparation prior to whipstock installation:

1. Determine casing size, weight, and grade (if possible) to assure the correct Whipstock andMills are ordered.

2. Run a casing calibration log and casing scraper run prior to setting the bridge plug. A

bridge plug or false bottom is required to activate, or set, the anchor mechanism on theWhipstock. The bridge plug or false bottom should be set 5 to 6 feet (1.5 to 2 meters)

above a casing collar in a full joint of casing.3. To insure the well bore is free of restrictions or doglegs, which could possibly cause a

premature shearing of the Whipstock, it is recommended a drift run be made with a packed millingassembly. This will also verify bridge plug depth, bridge plug integrity, and the pipe tally.

Run one

B.H.A. #1 Whipstock - Starting Mill - Orientation Sub - Drill String

• Make up UBHO Sub (orientation sub) to the Starting Mill and orient the keyed sleeve to the faceof the Whipstock. Verify setting with Company Man or Directional Drillers.

• Make up UBHO sub and Starting Mill to one joint of drill pipe and attach the Starting Mill to theWhipstock.

• Remove the shipping guard from the anchor trip mechanism.

• Trip in hole in a slow and smooth manner. Any sudden stops or jerks, may result in a prematureshearing of setting bolt, causing the Whipstock to free fall to bottom.

• Stop short of tagging bridge plug.

• Rig up and run Gyro into the hole. Stop short of tagging bridge plug.

• Work Pipe to relive any torque and take readings with Gyro.

• Manually rotate drill string to orientate the Whipstock face to the desired hole azimuth. HaveCompany Man or Directional Drillers confirm orientation.

• Slowly run in while watching the weight indicator. When the drill string begins to take weight,STOP, and recheck orientation with the Company Man or Directional Drillers.

• If readings are good, pull Gyro out of orientation sub.

Set down weight on the Whipstock to shear the roll pin and cap screw on the spring loaded plunger,thus setting the slip on the anchor mechanism

starting mill

guide lug

shear bolt

slip

bridge plug

RUN #2

8/20/2019 BlkMax


watermelon

mill

window

mill

• After setting the Slip, set down additional weight to shear the setting bolt from the Whipstock. After shearing the setting bolt, pick up a short distance and set weight on Whipstock again.

• Pick up and manually rotate the drill string to insure the setting bolt has sheared and the starting

Mill is free from the Whipstock.• Pull Gyro out of hole. Survey on the way out if required.

• Kick in the pumps and engage the rotary table or power swivel.

• Slowly lower drill string and begin milling procedures.

• Once the desired milling depth is reached with Starting Mill, circulate the hole clean and trip out of the hole. Casing cuttings will be collected on the Ditch Magnets.

• Visually inspect the bottom hole assembly for any signs of unusual wear.

Run Two

B.H.A. #2 Window Mill - Watermelon Mill - Bit Sub - Drill Collars - Drill String

• Pick up drill collars or heavy weight and one joint of drill pipe.

• Make up the Bit Sub, Watermelon Mill and Window Mill.

• Run in the hole with the second milling assembly and stop short of the top of the Whipstock. Donot hit the top of the Whipstock.

• Kick in the pumps and engage the rotary table or power swivel.

• Slowly lower the drill string until you begin picking up torque.

• Continue milling procedures through out the length of the Whipstock face.

• Once off the face of the Whipstock, continue drilling until there is a short open hole made.

• While rotating, make a couple of passes throughout the entire length of the Whipstock face tocheck for any tight spots.

• Pick up above the top of the whipstock and disengage rotary table or the power swivel. Make acouple of passes (without rotating) throughout the entire length of the Whipstock Face to check for any tight spots.

• Circulate hole clean and pull out of the hole.

• Gage Window Mill to insure a full gage hole has been milled.

WHIPSTOCKS

Casing hipstock Use Mill Use MillCasing hipstock

8/20/2019 BlkMax


Dia.

(in)

Dia.

(mm)

Wt.

(lb/ft)

Wt.

(kg/m)

Dia.

(in)

Dia.

(mm)

Dia.

(in)

Dia.

(mm)

13.5 20.09 3 1/2 88.9 3 3/4 95.3

11 16.37 3 1/2 88.9 3 7/8 98.4

9.5 14.14 3 1/2 88.9 3 7/8 98.44 3/4 121 16 23.81 3 1/2 88.9 3 3/4 95.3

23.2 34.52 3 7/8 98.4 4 1/8 104.8

18 26.79 4 101.6 4 1/8 104.8

15 22.32 4 101.6 4 1/4 108.0

13 19.35 4 101.6 4 3/8 111.1

11.5 17.11 4 101.6 4 3/8 111.1

23 34.23 4 1/4 108.0 4 1/2 114.3

20 29.76 4 1/4 108.0 4 5/8 117.5

17 25.30 4 1/2 114.3 4 3/4 120.7

15.5 23.07 4 1/2 114.3 4 3/4 120.7

14 20.83 4 1/2 114.3 4 7/8 123.813 19.35 4 1/2 114.3 4 7/8 123.8

23 34.23 4 1/2 114.3 5 1/8 130.2

20 29.76 4 1/2 114.3 5 1/8 130.2

18 26.79 4 1/2 114.3 5 1/4 133.4

15 22.32 4 1/2 114.3 5 3/8 136.5

32 47.62 5 1/4 133.4 5 1/2 139.7

28 41.67 5 1/4 133.4 5 5/8 142.9

24 35.71 5 1/4 133.4 5 3/4 146.1

20 29.76 5 1/2 139.7 5 7/8 149.2

17 25.30 5 1/2 139.7 6 152.4

38 56.55 5 1/4 133.4 5 3/4 146.1

35 52.08 5 1/2 139.7 5 7/8 149.232 47.62 5 1/2 139.7 5 7/8 149.2

29 43.15 5 1/2 139.7 6 152.4

26 38.69 5 1/2 139.7 6 1/8 155.6

23 34.23 5 1/2 139.7 6 1/8 155.6

20 29.76 5 1/2 139.7 6 1/4 158.8

17 25.30 5 1/2 139.7 6 3/8 161.9

178

127

140

152

168

4 1/2

6 5/8

7

5

114

5 1/2

6

Dia.

(in)

Dia.

(mm)

Wt.

(lb/ft)

Wt.

(kg/m)

Dia.

(in)

Dia.

(mm)

Dia.

(in)

Dia.

(mm)

39 58.04 6 152.4 6 1/2 165.1

33.7 50.15 6 152.4 6 5/8 168.3

29.7 44.20 6 1/4 158.8 6 3/4 171.526.4 39.29 6 1/4 158.8 6 3/4 171.5

24 35.71 6 1/4 158.8 6 7/8 174.6

20 29.76 6 1/4 158.8 7 177.8

49 72.92 7 177.8 7 3/8 187.3

44 65.48 7 177.8 7 1/2 190.5

40 59.52 7 177.8 7 1/2 190.5

36 53.57 7 177.8 7 5/8 193.7

32 47.62 7 177.8 7 3/4 196.9

28 41.67 7 177.8 7 7/8 200.0

24 35.71 7 177.8 7 7/8 200.0

53.5 79.61 8 203.2 8 3/8 212.747 69.94 8 203.2 8 1/2 215.9

43.5 64.73 8 203.2 8 1/2 215.9

40 59.52 8 203.2 8 5/8 219.1

36 53.57 8 203.2 8 3/4 222.3

32.3 48.07 8 203.2 8 3/4 222.3

29.3 43.60 9 228.6 8 7/8 225.4

55.5 82.59 9 228.6 9 1/2 241.3

51 75.89 9 228.6 9 5/8 244.5

45.5 67.71 9 228.6 9 3/4 247.7

40.5 60.27 9 228.6 9 3/4 247.7

32.75 48.74 9 228.6 9 7/8 250.8

60 89.29 10 254.0 10 1/2 266.754 80.36 10 254.0 10 5/8 269.9

47 69.94 10 254.0 10 3/4 273.1

42 62.50 10 254.0 10 3/4 273.1

38 56.55 10 254.0 10 7/8 276.2

72 107.14 11 1/2 292.1 12 1/8 308.0

68 101.19 11 1/2 292.1 12 1/8 308.0

61 90.77 11 1/2 292.1 12 1/4 311.2

54.5 81.10 11 1/2 292.1 12 1/4 311.2

48 71.43 11 1/2 292.1 12 3/8 314.3

194

219

244

273

298

34013 3/8

7 5/8

8 5/8

11 3/4

10 3/4

9 5/8

8/20/2019 BlkMax


CANFISH SERVICES

CanFish Services Inc. is a Canadian company that provides specialty oilfield rental, sales and servicetoCanadianand Internationaloil andgas producers CanFishServices corebusiness is theprovision

8/20/2019 BlkMax


to Canadian and International oil and gas producers. CanFish Services core business is the provisionof Fishing Tool Services including manufacture and sale of fishing tool equipment, engineering andplanning, well site supervision and rental of all types of Fishing Tools and Fishing Tool Services inconjunction with Wireline Pipe Recovery Services.

Specific services include:Open Hole Fishing ServicesWork Over Planning and ExecutionRemedial Work Over Execution

Whipstock and Sidetrack ServicesOne Trip WhipstocksWashover Burning ShoesCasing Cutting and RetrievalSpearsMilling ToolsEconomills

High Performance Pilot MillsGeneral Rental ToolsCasing RollersComplete Wireline Pipe Recovery ServicesBack Off Equipment

Chemical CuttingCased Hole Fishing ServicesPacker Milling and Retrieving

Coiled Tubing FishingRetrievable WhipstocksWashover Pipe and AccessoriesCasing PatchesOver-shotsTaper Taps and Die CollarsJunk Mills

Taper MillsSection MillsCasing Repair Driving SwagesFree Point Tools 1 l/16” - 1.3/8”Jet Cutting

General Wireline Services

CanFish Services Inc. has approximately fifteen Fishing Tool Supervisors on staff with an averageminimumof eighteenyears direct fieldexperience WealsohaveseveralFishingToolSupervisors with

8/20/2019 BlkMax


minimum of eighteen years direct field experience. We also have several Fishing Tool Supervisors withsignificant international experience working onshore and offshore in the North Sea, Middle East andSouth East Asia.

Locations

CanFish Services Ltd.Bay 1 1804 4 StNisku, Alberta

Ph: (780) 955-8998Fx: (780) 955-8944

CanFish Services Ltd.Suite 1410Calgary, AlbertaPh: (403) 231-9140

Fx: (403) 231-9140

CanFish Services Inc10903 78 Ave.Grande Prairie, Alberta

Ph: (780) 532-7713Fx: (780) 513-4161

Lloydminister Agent:Tryton Tools Services Ltd.37093 – 56b Ave.Lloydminister, Alberta

Ph: (780) 875-0800Fx: (780) 875-8731

8/20/2019 BlkMax


TORQUE CONNECTIONS

111/16 2 1/16

2.375 &

Short

2.875&

Short 31/8 33/8 33/4

4.75 &

Short 5 51/2 61/2

61/2

Short. 63/4 71/2

8&

Short

8"

Series 3 95/8

95/8

Short 111/4

End Cap 200 500 500 1000 1200 1500 1500 4000 4000 4500 6500 6500 6500 12000 12000 12000 25000 25000 60000

Body Connection 300 600 1000 2000 3000 3500 4500 10000 12000 15000 22000 22000 22000 35000 40000 40000 60000 60000 75000Mandrel To Washpipe 120 200 250 500 1000 1250 1500 3000 4000 4500 6000 11000 6000 10000 12000 12000 35000 50000

Preload Nut200

short only

400short only 400

D.S. To Washpipe 100 150 200 400 800 1000 1000 2500 3500 4000 5500 10000 5500 9000 11000 11000 18000 25000 40000

D.S. To Rotor 100 150 200 400 800 1000 1000 2500 3500 4000 5500 5500 5500 9000 11000 11000 18000 25000 40000

Adj. Mandrel 800 2000 2000 3500 3500 10000 12000 13000 22000 22000 22000 35000 40000 40000 60000 60000 75000

Stab/Thread Protector 3500 8000 10000 12000 12000 12000 24000 30000 30000 38000 38000 75000

BUILD RATESDEGREES per 100ft

Tool Size (in) Hole Size (in) .39° .78° 1.15° 1.50° 1.83° 2.12° 2.38° 2.60° 2.77° 2.90° 2.97° 3.00°

2 7/8 3 1/2 0 2 3 9 8 9 14 4 20 3 26 3 32 4 38 6 44 9 51 2 57 6 63 9

8/20/2019 BlkMax


NOTE! All calculations contained herein are based on slick drilling assemblies. Addition of stabilization may significantlyalter dog leg expectancies. Formation, competence, or lack thereof, may also adversely affect the accuracy of the abovepredictions.

2 7/8 3 1/2 0.2 3.9 8.9 14.4 20.3 26.3 32.4 38.6 44.9 51.2 57.6 63.9

4 1/2 1.9 5.7 10.1 14.8 19.8 25.1 30.6 36.2 41.9

3 1/8 3 3/4 3.4 9 15.3 22.1 29.2 36.4 43.8 51.3 58.8 66.4 74.1

3 7/8 1.8 6.6 12.5 18.9 25.7 32.7 39.9 47.1 54.6 62 69.6

4 3/4 3.3 8 13.2 18.8 24.7 30.9 37.4 43.9

3 3/8 4 1/2 1.8 5.2 9.2 13.6 18.2 23 27.9 32.9 38 43.1 48.2

4 3/4 3.3 6.9 11 15.3 19.9 24.6 29.4 34.3 39.3 44.3

5 7/8 2.4 5.5 9 12.7 16.7 20.9 25.2 29.7

3 3/4 4 1/2 1.3 5.7 10.8 16.4 22.2 28.3 34.4 40.7 47.1 53.5 59.9

4 3/4 2.7 7.2 12.2 17.6 23.3 29.1 35.2 41.3 47.5 53.8

5 7/8 3.1 7.1 11.5 16.2 21.2 26.3 31.7

4 3/4 6 2.2 5 8.1 11.4 14.9 18.4 22 25.6 29.3 33 36.7

6 1/8 1.7 4.4 7.4 10.6 14 17.5 21 24.6 28.3 31.9 35.6

6 1/4 1.3 3.8 6.7 9.9 13.2 16.6 20.1 23.7 27.3 30.9 34.6

6 1/2 2.8 5.5 8.5 11.7 15 18.4 21.9 25.4 29 32.6

6 3/4 2 4.4 7.2 10.3 13.5 16.8 20.2 23.6 27.1 30.7

4 3/4 SH 6 1.8 5 8.9 13.1 17.5 22.1 26.8 31.6 36.4 41.4 46.3

6 1/8 1.2 4.1 7.8 11.8 16.1 20.6 25.2 29.9 34.7 39.6 44.5

6 1/4 3.3 6.8 10.7 14.8 19.2 23.7 28.4 33.1 37.9 42.76 1/2 1.9 5 8.5 12.4 16.6 20.9 25.4 30 34.6 39.4

6 3/4 3.4 6.6 10.3 14.2 18.3 22.6 27.1 31.6 36.2

5 6 2.4 5.5 9 12.7 16.5 20.4 24.4 28.4 32.4 36.5 40.6

6 1/8 1.8 4.7 8.1 11.7 15.5 19.3 23.2 27.2 31.2 35.2 39.3

6 1/4 1.3 4 7.3 10.8 14.4 18.2 22.1 26 30 34 38

6 1/2 2.8 5.8 9.1 12.6 16.2 20 23.8 27.7 31.6 35.6

6 3/4 1.8 4.5 7.5 10.9 14.4 18 21.7 25.5 29.4 33.3

5 1/2 6 3/4 1.9 4.5 7.3 10.3 13.4 16.5 19.8 23 26.3 29.5 32.8

7 7/8 1 3 5.4 8 10.8 13.6 16.6 19.6 22.7 25.8

6 1/2 7 7/8 1.6 4 6.6 9.4 12.2 15.2 18.2 21.2 24.3 27.3 30.4

8 1/2 2.1 4.3 6.8 9.4 12.2 15 17.9 20.9 23.8 26.8

8 3/4 1.5 3.6 5.9 8.5 11.1 13.9 16.7 19.6 22.5 25.5

9 5/8 1.4 3.3 5.5 7.9 10.4 13 15.7 18.4 21.3

6 1/2 Short 7 7/8 1.3 3.9 7 10.2 13.7 17.2 20.8 24.4 28.1 31.9 35.6

8 1/2 1.5 3.9 6.8 9.8 13 16.4 19.8 23.3 26.9 30.5

8 3/4 0.7 3 5.6 8.5 11.6 14.2 18.2 21.6 25 28.6

9 5/8 0.2 2.2 4.6 7.2 10.1 13.1 16.2 19.4 22.7

6 3/4 7 7/8 1.8 4.2 6.9 9.7 12.6 15.5 18.5 21.5 24.5 27.5 30.6

8 1/2 2.2 4.5 7.1 9.7 12.5 15.3 18.2 21.1 24.1 27

8 3/4 1.6 3.8 6.2 8.7 11.4 14.2 17 19.9 22.8 25.7

9 5/8 1.5 3.5 5.7 8.1 10.6 13.3 15.9 18.7 21.5

BUILD RATESDEGREES per 100ft

Tool Size (in) Hole Size (in) .39° .78° 1.15° 1.50° 1.83° 2.12° 2.38° 2.60° 2.77° 2.90° 2.97° 3.00°

7 1/2 9 5/8 1.5 3.5 5.8 8.2 10.7 13.4 16 19.3 21.5 24.3

9 3/4 1 2 3 2 5 4 7 8 10 3 12 9 15 5 18 2 21 23 7

8/20/2019 BlkMax


2 3/8

FIXED HOUSING

NOTE! All calculations contained herein are based on slick drilling assemblies. Addition of stabilization may significantly alter dogleg expectancies. Formation, competence, or lack thereof, may also adversely affect the accuracy of the above predictions

9 3/4 1.2 3.2 5.4 7.8 10.3 12.9 15.5 18.2 21 23.7

9 7/8 1 2.8 5 7.4 9.8 12.4 15 17.7 20.4 23.2

10 5/8 1.2 3.1 5.1 7.4 9.8 12.2 14.7 17.3 20

8 9 7/8 2.1 4.2 6.5 9 11.5 14.1 16.7 19.4 22.1 24.8

10 5/8 2.4 4.4 6.6 8.9 11.4 13.9 16.4 19 21.6

12 1/4 1 2.7 4.6 6.6 8.8 11 13.3 15.7

8 SH 9 7/8 1.6 3.9 6.6 9.4 12.4 15.5 18.7 21.9 25.2 28.4

10 5/8 1.6 3.8 6.2 8.9 11.7 14.7 17.7 20.8 23.9

12 1/4 3.2 5.4 7.9 10.4 13.1 15.8

9 5/8 12 1/4 2 3.9 6.1 8.4 10.8 13.3 15.8 18.4 21 23.7

13 1/2 1.5 3.1 5.1 7.1 9.3 11.6 14 16.4 18.9

14 3/4 1 2.5 4.3 6.2 8.2 10.4 12.6 14.9

17 1/2 1 2.6 4.2 6 7.8

11 1/4 12 1/4 4.7 6.9 9.3 11.6 14 16.3 18.7 21.1 23.5 25.9

13 1/2 3.8 5.8 7.9 10 12.3 14.5 16.8 19 21.4

14 3/4 3.3 5.1 7 9 11.1 13.2 15.4 17.6

17 1/2 3.8 5.4 13.9 9 10.9

T o o l S iz e ( i n ) H o le S i z e ( in ) 1 . 2 5 ° 1 . 5 ° 3 . 0 ° 4 . 0 °

2 1 / 1 6 2 7 / 8 1 3 . 7 1 9 . 8 5 9 . 9 8 8 . 23 3 / 8 5 . 6 1 0 . 6 4 6 . 7 7 3 . 5

3 1 / 2 4 8 . 7 4 3 . 8 7 0 . 2

2 3 / 8 3 1 / 8 1 4 . 9 2 1 . 4 6 3 . 8 9 3 . 5

3 3 / 4 4 . 1 9 4 5 7 3 . 6

4 1 / 2 - - 2 9 . 1 5 4

Tool Size (in) Hole Size (in) 0.39° 0.77° 1.11° 1.41° 1.66° 1.85° 1.96° 2°

2 3/8 3 1/8 1.8 6.7 12.7 19.2 26.1 33.3 40.6

3 1/4 0.3 4.6 10 16.2 22.8 29.7 36.8

3 7/8 0.5 4.8 9.8 15.3 21.3

4 1/2 0.8 5.1 9.8

8/20/2019 BlkMax


PISTON DEPTHS

Tool Size Bottomed Out (In) Piston Depth (In)

“A”

8/20/2019 BlkMax


WHEN PISTON REACHES OR EXCEEDS“PISTON DEPTH”, CHANGE OUT TOOLS

( ) p ( )

1 11/16" 13/16" 9/16"

2 1/16" 1 1/4" 1"

2 3/8" & Short 1 1/4" 1"

2 7/8" & Short 1 11/16" 1 7/16"

3 1/8" 1 3/16" 15/16"

3 3/8" 1 7/16" 1 3/16"

3 3/4" 1 7/16" 1 3/16"

4 3/4" 2 5/8" 2 3/8"

4 3/4" Short 2 11/16" 2 3/8"

5" 2 1/4" 2"

5" Series 3 2 1/4" 2"

5 1/2" 2 13/16" 2 9/16"6 1/2" Short 2 3/16" 1 15/16"

6 3/4" 2 3/16" 1 15/16"

7 1/2" 3" 2 3/4"

8" 3 1/4" 3"

8" Short 2 5/16" 2 1/16"

8" Series 3 2 5/16" 2 1/16"

9 5/8" 2 3/8" 2 1/8"

9 5/8" Short 3 11/16" 3 7/16"

11 1/4" 4 1/8" 3 7/8"

" A "

MOTOR FISHING DIMENSIONS

8/20/2019 BlkMax


Motor Lobes Stages A B C D E F G H J K L M N P Q

1 11/16 1-2 3 - 18 - 30 81 84 - 1.67 1.67 - 1.67 1.24 1.67 0.56 1.67

1 11/16 5-6 3 - 18 - 30 93 95 - 1.67 1.67 - 1.67 1.24 1.67 0.56 1.67

1 11/16 5-6 5 - 18 - 30 126 129 - 1.67 1.67 - 1.67 1.24 1.67 0.56 1.67

2 1/16 1-2 2 - 24 - 35 95 99 - 2.06 2.06 - 2.06 1.40 2.06 0.62 2.06

2 1/16 4-5 1 - 24 - 35 72 76 - 2.06 2.06 - 2.06 1.40 2.06 1.27 2.06

2 1/16 4-5 2 - 24 - 35 101 104 - 2.06 2.06 - 2.06 1.40 2.06 1.27 2.06

2 3/8 1-2 7 - 27 42 47 102 107 - 2.37 2.37 2.62 2.37 1.47 2.37 1.14 2.37

2 3/8 2-3 4 - 27 42 47 130 137 - 2.37 2.37 2.62 2.37 1.47 2.37 1.27 2.37

2 3/8 4-5 3 - 27 42 47 102 107 - 2.37 2.37 2.62 2.37 1.47 2.37 1.28 2.37

2 3/8 5-6 2.5 - 27 42 47 102 107 - 2.37 2.37 2.62 2.37 1.47 2.37 1.33 2.37

2 7/8 1-2 5.2 - 30 48 54 162 178 - 2.87 2.87 3.03 2.93 2.01 2.87 1.59 2.87

2 7/8 2-3 7 - 30 48 54 145 151 - 2.87 2.87 3.03 2.93 2.01 2.87 1.75 2.87

2 7/8 3-4 4 - 30 48 54 109 114 - 2.87 2.87 3.03 2.93 2.01 2.87 1.68 2.87

2 7/8 5-6 3.3 - 30 48 54 109 114 - 2.87 2.87 3.03 2.93 2.01 2.87 1.66 2.87

2 7/8 7-8 2.5 - 30 48 54 109 106 - 2.87 2.87 3.03 2.93 2.01 2.87 1.85 2.87


8/20/2019 BlkMax



3 1/8 7-8 2.5 - 22 35 41 89 93 - 3.12 3.12 3.25 3.12 2.19 2.87 1.85 2.87

3 1/8 7-8 3 - 22 35 41 142 107 - 3.12 3.12 3.25 3.12 2.19 3.12 1.97 3.12

3 1/8 7-8 4 - 22 35 41 111 115 - 3.12 3.12 3.25 3.12 2.19 3.12 1.85 3.12

3 3/8 1-2 5 - 40 55 64 223 247 - 3.38 3.62 3.87 3.62 2.46 3.37 1.88 3.37

3 3/8 4-5 5 - 40 55 64 175 188 - 3.38 3.62 3.87 3.62 2.46 3.37 1.94 3.37

3 3/8 7-8 2.5 - 40 55 64 157 169 - 3.38 3.62 3.87 3.62 2.46 3.37 1.96 3.37

3 3/8 7-8 3 - 40 55 64 175 188 - 3.38 3.62 3.87 3.62 2.46 3.37 1.96 3.37

3 3/8 9-10 3 - 40 55 64 119 125 - 3.38 3.62 3.87 3.62 2.46 3.50 2.16 3.50

3 3/4 4-5 3.5 - 44 - 52 181 193 - 3.75 3.62 3.87 3.62 2.74 3.75 2.16 3.75

3 3/4 4-5 5 - 44 - 52 163 176 - 3.75 3.62 3.87 3.62 2.74 3.37 1.94 3.37

3 3/4 7-8 2.3 - 44 - 52 181 193 - 3.75 3.62 3.87 3.62 2.74 3.75 2.25 3.753 3/4 7-8 3 - 44 - 52 163 176 - 3.75 3.62 3.87 3.62 2.74 3.37 1.96 3.37

3 3/4 9-10 2 - 44 - 52 92 97 - 3.75 3.62 3.87 3.62 2.74 3.50 2.16 3.50

3 3/4 9-10 3 - 44 - 52 92 110 - 3.75 3.62 3.87 3.62 2.74 3.50 2.16 3.50

4 1/8 6-7 3 - 39 57 65 221 225 - 4.13 4.13 - 4.13 2.88 3.88 2.25 3.88

4 1/8 7-8 2 - 39 57 65 221 225 - 4.13 4.13 - 4.13 2.88 3.88 2.23 3.88

4 3/4 1-2 3 16 57 85 93 225 236 5.50 4.80 5.00 5.37 5.00 3.00 4.75 2.43 4.75

8/20/2019 BlkMax



8/20/2019 BlkMax



5 1/2 9-10 3.4 24 65 95 103 231 237 6.25 5.53 5.53 5.75 5.53 3.65 5.50 3.49 5.53

6 1/2 1-2 4 24 70 100 116 294 302 7.13 6.56 6.56 6.87 6.75 3.53 6.50 3.43 6.56

6 1/2 4-5 4.8 24 70 100 116 255 269 7.13 6.56 6.56 6.87 6.75 3.53 6.50 4.22 6.56

6 1/2 6-7 5 24 70 100 116 310 316 7.13 6.56 6.56 6.87 6.75 3.53 6.50 4.32 6.56

6 1/2 7-8 3 24 70 100 116 232 247 7.13 6.56 6.56 6.87 6.75 3.53 6.50 4.52 6.56

6 1/2 8-9 2 24 70 100 116 195 202 7.13 6.56 6.56 6.87 6.75 3.53 6.50 4.6 6.56

6 1/2 8-9 3 24 70 100 116 232 237 7.13 6.56 6.56 6.87 6.75 3.53 6.50 4.32 6.56

6 1/2 S 1-2 4 16 53 78 94 274 280 7.13 6.56 6.56 6.87 6.75 3.65 6.50 3.43 6.56

6 1/2 S 4-5 4.8 16 53 78 94 235 247 7.13 6.56 6.56 6.87 6.75 3.65 6.50 4.22 6.56

6 1/2 S 6-7 5 16 53 78 94 288 294 7.13 6.56 6.56 6.87 6.75 3.65 6.50 4.32 6.56

6 1/2 S 7-8 2 16 53 78 94 241 247 7.13 6.56 6.56 6.87 6.75 3.65 6.50 4.52 6.56

6 1/2 S 7-8 3 16 53 78 94 212 225 7.13 6.56 6.56 6.87 6.75 3.65 6.50 4.52 6.56

6 1/2 S 8-9 2 16 53 78 94 175 180 7.13 6.56 6.56 6.87 6.75 3.65 6.50 4.60 6.56

6 1/2 S 8-9 3 16 53 78 94 212 215 7.13 6.56 6.56 6.87 6.75 3.65 6.50 4.32 6.56

6 3/4 4-5 4.8 26 71 101 117 256 270 7.13 6.75 6.75 7.00 6.75 3.50 6.75 4.22 6.75


8/20/2019 BlkMax



6 3/4 4-5 7 26 71 101 117 313 327 7.13 6.75 6.75 7.00 6.75 3.50 6.75 4.22 6.75

6 3/4 5-6 7 26 71 101 117 309 317 7.13 6.75 6.75 7.00 6.75 3.50 6.75 4.27 6.75

6 3/4 6-7 5 26 71 101 117 309 317 7.13 6.75 6.75 7.00 6.75 3.50 6.75 4.32 6.75

6 3/4 7-8 2 26 71 101 117 262 270 7.13 6.75 6.75 7.00 6.75 3.50 6.75 4.30 6.75

6 3/4 7-8 3 26 71 101 117 233 348 7.13 6.75 6.75 7.00 6.75 3.50 6.75 4.52 6.75

6 3/4 8-9 2 26 71 101 117 202 204 7.13 6.75 6.75 7.00 6.75 3.50 6.75 4.60 6.75

6 3/4 8-9 3 26 71 101 117 233 242 7.13 6.75 6.75 7.00 6.75 3.50 6.75 4.60 6.75

7 1/2 4-5 3.6 29 74 103 119 272 287 8.50 7.50 7.50 7.75 7.50 4.89 7.50 4.94 7.50

7 1/2 7-8 3 29 74 103 119 272 287 8.50 7.50 7.50 7.75 7.50 4.89 7.50 5.19 7.50

8 1-2 4 32 77 112 123 303 310 9.00 8.03 8.03 8.50 8.03 4.89 8.03 4.36 8.03

8 4-5 3.6 32 77 112 123 277 291 9.00 8.03 8.03 8.50 8.03 4.89 8.03 4.94 8.03

8 7-8 3 32 77 112 123 277 291 9.00 8.03 8.03 8.50 8.03 4.89 8.03 5.19 8.03

8 8-9 4 32 77 112 123 303 310 9.00 8.03 8.03 8.50 8.03 4.89 8.03 5.46 8.03

8 S 1-2 4 36 60 94 106 283 293 9.00 8.03 8.03 8.50 8.03 4.89 8.03 4.36 8.03

8 S 4-5 3.6 36 60 94 106 258 274 9.00 8.03 8.03 8.50 8.03 4.89 8.03 4.94 8.03


8/20/2019 BlkMax



8 S 7-8 3 36 60 94 106 258 274 9.00 8.03 8.03 8.50 8.03 4.89 8.03 5.19 8.03

8 S 8-9 4 36 60 94 106 264 276 9.00 8.03 8.03 8.50 8.03 4.89 8.03 5.46 8.03

9 5/8 2-3 7.5 25 71 108 125 329 333 12.00 10.75 9.62 9.87 9.62 6.62 9.62 6.27 9.62

9 5/8 3-4 4.5 25 71 108 125 294 303 12.00 10.75 9.62 9.87 9.62 6.62 9.62 5.98 9.62

9 5/8 4-5 4 25 71 108 125 271 279 12.00 10.75 9.62 9.87 9.62 6.62 9.62 6.21 9.62

9 5/8 5-6 3 25 71 108 125 294 303 12.00 10.75 9.62 9.87 9.62 6.62 9.62 6.24 9.62

11 1/4 3-4 3.6 - 76 123 142 332 343 12.25 11.25 11.25 11.75 11.25 7.73 11.25 9.97 11.25

Casing Dimensions and Bit Clearances(dimensions in in. unless noted otherwise)

OD Wt Wall ID OD Drift Bit Bit Clearance OD Wt Wall ID OD Drift Bit Bit Clearance

8/20/2019 BlkMax


OD Wt. Wall ID OD Drift Bit Bit Clearance(lb/ft) Size Size

4 ½

9.5 0.205 4.090 5.000 3.965 3 7/8 3.875 0.09011.6 0.250 4.000 5.000 3.875 3 7/8 3.875 0.00013.5 0.290 3.920 5.000 3.795 3 3/4 3.750 0.04515.1 0.337 3.826 5.000 3.701 3 5/8 3.625 0.076

511.5 0.220 4.560 5.563 4.435 4 1/4 4.250 0.18513.0 0.253 4.494 5.563 4.369 4 1/4 4.250 0.11915.0 0.296 4.408 5.563 4.283 4 1/4 4.250 0.03318.0 0.362 4.276 5.563 4.151 4 1/8 4.125 0.026

5 ½13.0 0.228 5.044 6.050 4.919 4 3/4 4.750 0.16914.0 0.244 5.012 6.050 4.887 4 3/4 4.750 0.13715.5 0.275 4.950 6.050 4.825 4 3/4 4.750 0.07517.0 0.304 4.892 6.050 4.767 4 3/4 4.750 0.01720.0 0.361 4.778 6.050 4.653 4 5/8 4.625 0.02823.0 0.415 4.670 6.050 4.545 4 1/2 4.500 0.045

6

15.0 0.238 5.524 6.625 5.399 5 3/8 5.375 0.02418.0 0.288 5.425 6.625 5.299 5 1/8 5.125 0.17420.0 0.324 5.352 6.625 5.227 5 1/8 5.125 0.10223.0 0.380 5.240 6.625 5.115 4 7/8 4.875 0.24026.0 0.434 5.132 6.625 5.007 4 7/8 4.875 0.132


6 5/8

17.0 0.245 6.135 7.390 6.010 6 6.000 0.01020.0 0.288 6.049 7.390 5.924 5 7/8 5.875 0.04924.0 0.352 5.921 7.390 5.796 5 3/4 5.750 0.04628.0 0.417 5.791 7.390 5.666 5 5/8 5.625 0.04132.0 0.475 5.675 7.390 5.550 5 3/8 5.375 0.175

717.0 0.231 6.538 7.656 6.413 6 3/8 6.375 0.03820.0 0.272 6.456 7.656 6.331 6 1/4 6.250 0.08123.0 0.317 6.366 7.656 6.241 6 1/8 6.125 0.116

26.0 0.362 6.276 7.656 6.151 6 1/8 6.125 0.02629.0 0.408 6.184 7.656 6.059 6 6.000 0.05932.0 0.453 6.094 7.656 5.969 5 7/8 5.875 0.09435.0 0.498 6.004 7.656 5.879 5 7/8 5.875 0.00438.0 0.540 5.920 7.656 5.795 5 3/4 5.750 0.045

7 5/820.0 0.250 7.125 8.500 7.000 6 3/4 6.750 0.25024.0 0.300 7.025 8.500 6.900 6 3/4 6.750 0.150

26.4 0.328 6.969 8.500 6.844 6 3/4 6.750 0.09429.7 0.375 6.875 8.500 6.750 6 3/4 6.750 0.00033.7 0.430 6.765 8.500 6.640 6 5/8 6.625 0.01539.0 0.500 6.625 8.500 6.500 6 3/8 6.375 0.125

Casing Dimensions and Bit Clearances(dimensions in in. unless noted otherwise)

OD Wt Wall ID OD Drift Bit Bit Clearance OD Wt Wall ID OD Drift Bit Bit Clearance

8/20/2019 BlkMax



8 5/8

24.0 0.2648.097 9.625 7.972 7 7/8 7.875 0.09728.0 0.3048.017 9.625 7.892 7 7/8 7.875 0.01732.0 0.3527.921 9.625 7.796 7 3/4 7.750 0.04636.0 0.4007.825 9.625 7.700 7 5/8 7.625 0.07540.0 0.4507.725 9.625 7.600 7 3/8 7.375 0.22544.0 0.5007.625 9.625 7.500 7 3/8 7.375 0.12549.0 0.5577.511 9.625 7.386 7 3/8 7.375 0.011

9 5/829.3 0.2819.063 10.625 8.907 8 3/4 8.750 0.157

32.3 0.3129.001 10.625 8.845 8 3/4 8.750 0.09536.0 0.3528.921 10.625 8.765 8 3/4 8.750 0.01540.0 0.3958.835 10.625 8.697 8 5/8 8.625 0.07243.5 0.4358.755 10.625 8.599 8 1/2 8.500 0.09947.0 0.4728.681 10.625 8.525 8 1/2 8.500 0.02553.5 0.5458.535 10.625 8.379 8 3/8 8.375 0.004

10 3/432.75 0.27910.19211.750 10.0369 7/8 9.875 0.16140.50 0.35010.05011.750 9.894 9 7/8 9.875 0.019

45.50 0.4009.950 11.750 9.794 9 3/4 9.750 0.04451.00 0.4509.850 11.750 9.694 9 5/8 9.625 0.06955.50 0.4959.760 11.750 9.604 9 9.000 0.60460.70 0.5459.660 11.750 9.504 9 9.000 0.50465.70 0.5959.560 11.750 9.404 9 9.000 0.404


11 3/4

38.00 0.30011.15012.750 10.99410 5/8 10.625 0.36942.00 0.33311.08412.750 10.92810 5/8 10.625 0.30347.00 0.37511.00012.750 10.84410 5/8 10.625 0.21954.00 0.43510.88012.750 10.72410 5/8 10.625 0.09960.00 0.48910.77212.750 10.6169 7/8 9.875 0.741

13 3/848.00 0.33012.71514.375 12.55912 1/4 12.250 0.30954.50 0.38012.61514.375 12.45912 1/4 12.250 0.20961.00 0.43012.51514.375 12.35912 1/4 12.250 0.109

68.00 0.48012.41514.375 12.25912 1/4 12.250 0.00972.00 0.51412.37414.375 12.19110 10.000 2.191

1655.00 0.31215.37517.000 15.18815 15.000 0.18865.00 0.37515.25017.000 15.06215 15.000 0.06275.00 0.43815.12517.000 14.93814 3/4 14.750 0.18884.00 0.49515.01017.000 14.82314 3/4 14.750 0.073

20

94.00 0.438 19.124 21.000 18.936 17 1/2 17.500 1.436

Shouldered Connection Equivalents X-REF

Common Name Size Equivalent Connection

Internal flush(IF) 23/8 27/8slimhole; NC26

Common Name Size Equivalent Connection

DoubleStreamline(DSL) 31/2 27/8extrahole

8/20/2019 BlkMax


Internal flush (IF) 2 3/8 2 7/8 slimhole; NC 262 7/8 3 1/2 slimhole; NC 313 1/2 4 1/2 slimhole; NC 38

4 4 1/2 extra hole; NC 465 double streamline

Full hole (FH) 4 4 1/2 double streamline;NC 40

Extra hole (XH) (EH) 2 7/8 3 1/2 double streamline3 1/2 4 slimhole

4 1/2 external flush4 1/2 4 internal flush; NC 465 4 1/2 internal flush; NC 50

5 1/2 double streamline

Slimhole (SH) 2 7/8 2 3/8 internal flush; NC 263 1/2 2 7/8 internal flush; NC 314 3 1/2 extra hole

4 1/2 external flush

4 1/2 3 1/2 internal flush; NC 3

Double Streamline (DSL) 3 1/2 2 7/8 extra hole4 1/2 4 full hole; NC 405 1/2 4 1/2 internal flush

5 extra hole; NC 50

Numbered connection (NC) 26 2 3/8 internal flush2 7/8 slimhole

31 2 7/8 internal flush3 1/2 slimhole

38 3 1/2 internal flush4 1/2 slimhole

40 4 full hole4 1/2 double streamline

46 4 internal flush4 1/2 extra hole

50 4 1/2 internal flush5 extra hole5 1/2 double streamline

External flush (EF) 4 1/2 4 slimhole

3 1/2 extra hole

DRILL COLLAR WEIGHTS(lb/ft.)

D ill C ll O D C ll B (i )

8/20/2019 BlkMax


Drill Collar O.D.

1 1 1/4 1 1/2 1 3/4 2 2 1/4 2 1/2 2 13/16 3 3 1/4 3 1/2 3 3/4 4

2 7/8 19 18 16

3 21 20 183 1/8 22 22 20

3 1/4 26 24 22

3 1/2 30 29 27

3 3/4 35 33 32

4 40 39 37 35 32 29

4 1/8 43 41 39 37 35 32

4 1/4 46 44 42 40 38 35

4 1/2 51 50 48 46 43 41

4 3/4 54 52 50 47 44

Collar Bore (in.)

1 1 1/4 1 1/2 1 3/4 2 2 1/4 2 1/2 2 13/16 3 3 1/4 3 1/2 3 3/4 45 61 59 56 53 50

5 1/4 68 65 63 60 57

5 1/2 75 73 70 67 64 60

5 3/4 82 80 78 75 72 67 64 60

6 90 88 85 83 79 75 72 68

6 1/4 98 96 94 91 88 83 80 76 72

6 1/2 107 105 102 99 96 91 89 85 80

6 3/4 116 114 111 108 105 100 98 93 89

7 120 117 114 110 107 103 98 93 84

7 1/4 130 127 124 119 116 112 108 103 93

1 1 1/4 1 1/2 1 3/4 2 2 1/4 2 1/2 2 13/16 3 3 1/4 3 1/2 3 3/4 4

7 3/4 150 147 144 139 136 132 128 123 112

8 160 157 154 150 147 143 138 133 122

8 1/4 171 168 165 160 158 154 149 144 133

8 1/2 182 179 176 172 169 165 160 155 150

9 203 200 195 192 188 184 179 174

9 1/2 227 224 220 216 212 209 206 198

9 3/4 240 237 232 229 225 221 216 211

10 254 251 246 243 239 235 230 225

11 310 307 302 299 295 291 286 281

ANNULAR CAPACITIES

Drillpipe ∅ Hole Size Annular Capaci ty

8/20/2019 BlkMax


Drillpipe ∅(in)

Hole Size(in)

Annular Capaci ty(gal/ft)

5 12 1/4 5.10

9 7/8 2.968 3/4 2.10

8 1/2 1.93

4 1/2 12 1/4 5.30

9 7/8 3.15

8 1/2 2.12

7 7/8 1.70

3 1/2 6 3/4 1.36

6 1/2 1.22

6 1/8 1.04

2 7/8 4 3/4 0.58

4 1/2 0.49

4 1/8 0.36

3 7/8 0.27

( )24.51

DDgal/ftcapacityannular

2

p

2

h −=

HOLE CAPACITIES

OD ft3/ft ft/ft3 bbl/ft ft/bbl gal/ft ft/gal

1 0.0055 183.3465 0.001 1029.458 0.0408 24.5109

OD ft3/ft ft/ft3 bbl/ft ft/bbl gal/ft ft/gal

7 0.2673 3.7418 0.0476 21.0093 1.9991 0.5002

8/20/2019 BlkMax


1 1/8 0.0069 144.8664 0.0012 813.399 0.0516 19.3666

1 1/4 0.0085 117.3418 0.0015 658.8532 0.0637 15.687

1 3/8 0.0103 96.9767 0.0018 544.5068 0.0771 12.9644

1 1/2 0.0123 81.4873 0.0022 457.5369 0.0918 10.8937

1 5/8 0.0144 69.433 0.0026 389.854 0.1077 9.2822

1 3/4 0.0167 59.8682 0.003 336.1496 0.1249 8.00361 7/8 0.0192 52.1519 0.0034 292.8236 0.1434 6.972

2 0.0218 45.8366 0.0039 257.3645 0.1632 6.1277

2 1/8 0.0246 40.6027 0.0044 227.9769 0.1842 5.428

2 1/4 0.0276 36.2166 0.0049 203.3498 0.2065 4.8417

2 3/8 0.0308 32.5046 0.0055 182.5078 0.2301 4.3454

2 1/2 0.0341 29.3354 0.0061 164.7133 0.255 3.9217

2 5/8 0.0376 26.6081 0.0067 149.3998 0.2811 3.5571

2 3/4 0.0412 24.2442 0.0073 136.1267 0.3085 3.2411

2 7/8 0.0451 22.1818 0.008 124.5469 0.3372 2.9654

3 0.0491 20.3718 0.0087 114.3842 0.3672 2.7234

3 1/8 0.0533 18.7747 0.0095 105.4165 0.3984 2.5099

3 1/4 0.0576 17.3582 0.0103 97.4635 0.4309 2.3206

3 3/8 0.0621 16.0963 0.0111 90.3777 0.4647 2.1518

3 1/2 0.0668 14.9671 0.0119 84.0374 0.4998 2.00093 5/8 0.0717 13.9526 0.0128 78.3416 0.5361 1.8653

3 3/4 0.0767 13.038 0.0137 73.2059 0.5737 1.743

3 7/8 0.0819 12.2104 0.0146 68.5591 0.6126 1.6324

4 0.0873 11.4592 0.0155 64.3411 0.6528 1.5319

4 1/8 0.0928 10.7752 0.0165 60.5008 0.6942 1.4405

4 1/4 0.0985 10.1507 0.0175 56.9942 0.7369 1.357

4 3/8 0.1044 9.5789 0.0186 53.7839 0.7809 1.2806

4 1/2 0.1104 9.0541 0.0197 50.8374 0.8262 1.2104

4 5/8 0.1167 8.5713 0.0208 48.1266 0.8727 1.1459

4 3/4 0.1231 8.1262 0.0219 45.627 0.9205 1.0864

4 7/8 0.1296 7.7148 0.0231 43.3171 0.9696 1.0314

5 0.1364 7.3339 0.0243 41.1783 1.02 0.9804

5 1/8 0.1433 6.9805 0.0255 39.1941 1.0716 0.9332

5 1/4 0.1503 6.652 0.0268 37.35 1.1245 0.8893

5 3/8 0.1576 6.3462 0.0281 35.6329 1.1787 0.84845 1/2 0.165 6.061 0.0294 34.0317 1.2341 0.8103

5 5/8 0.1726 5.7947 0.0307 32.536 1.2909 0.7747

5 3/4 0.1803 5.5455 0.0321 31.1367 1.3489 0.7414

5 7/8 0.1883 5.312 0.0335 29.8259 1.4082 0.7101

6 0.1963 5.093 0.035 28.5961 1.4687 0.6809

6 1/8 0.2046 4.8872 0.0364 27.4408 1.5306 0.6534

6 1/4 0.2131 4.6937 0.0379 26.3541 1.5937 0.6275

6 3/8 0.2217 4.5114 0.0395 25.3308 1.6581 0.6031

6 1/2 0.2304 4.3396 0.041 24.3659 1.7237 0.5801

6 5/8 0.2394 4.1773 0.0426 23.4551 1.7907 0.5585

6 3/4 0.2485 4.0241 0.0443 22.5944 1.8589 0.538

6 7/8 0.2578 3.8791 0.0459 21.7803 1.9284 0.5186

7 1/8 0.2769 3.6116 0.0493 20.2786 2.0711 0.4828

7 1/4 0.2867 3.4882 0.0511 19.5854 2.1445 0.4663

7 3/8 0.2967 3.3709 0.0528 18.9271 2.219 0.4506

7 1/2 0.3068 3.2595 0.0546 18.3015 2.2949 0.4357

7 5/8 0.3171 3.1535 0.0565 17.7063 2.372 0.4216

7 3/4 0.3276 3.0526 0.0583 17.1398 2.4504 0.40817 7/8 0.3382 2.9565 0.0602 16.6 2.5301 0.3952

8 0.3491 2.8648 0.0622 16.0853 2.6111 0.383

8 1/8 0.3601 2.7773 0.0641 15.5942 2.6933 0.3713

8 1/4 0.3712 2.6938 0.0661 15.1252 2.7768 0.3601

8 3/8 0.3826 2.614 0.0681 14.6771 2.8616 0.3495

8 1/2 0.3941 2.5377 0.0702 14.2486 2.9477 0.3393

8 5/8 0.4057 2.4646 0.0723 13.8385 3.035 0.3295

8 3/4 0.4176 2.3947 0.0744 13.446 3.1236 0.3201

8 7/8 0.4296 2.3277 0.0765 13.0699 3.2135 0.3112

9 0.4418 2.2635 0.0787 12.7094 3.3047 0.3026

9 1/8 0.4541 2.2019 0.0809 12.3635 3.3971 0.2944

9 1/4 0.4667 2.1428 0.0831 12.0317 3.4908 0.2865

9 3/8 0.4794 2.0861 0.0854 11.7129 3.5858 0.2789

9 1/2 0.4922 2.0315 0.0877 11.4067 3.682 0.2716

9 5/8 0.5053 1.9791 0.09 11.1124 3.7796 0.2646

9 3/4 0.5185 1.9287 0.0923 10.8293 3.8784 0.2578

9 7/8 0.5319 1.8802 0.0947 10.5569 3.9785 0.2514

10 0.5454 1.8335 0.0971 10.2946 4.0798 0.2451

10 1/8 0.5591 1.7885 0.0996 10.042 4.1824 0.2391

10 1/4 0.573 1.7451 0.1021 9.7985 4.2864 0.2333

10 3/8 0.5871 1.7033 0.1046 9.5638 4.3915 0.2277

10 1/2 0.6013 1.663 0.1071 9.3375 4.498 0.2223

10 5/8 0.6157 1.6241 0.1097 9.1191 4.6057 0.2171

10 3/4 0.6303 1.5866 0.1123 8.9082 4.7147 0.2121

10 7/8 0.645 1.5503 0.1149 8.7046 4.825 0.2073

11 0.66 1.5153 0.1175 8.5079 4.9366 0.2026

11 1/8 0.675 1.4814 0.1202 8.3178 5.0494 0.198

11 1/4 0.6903 1.4487 0.1229 8.134 5.1635 0.1937

11 3/8 0.7057 1.417 0.1257 7.9562 5.2789 0.189411 1/2 0.7213 1.3864 0.1285 7.7842 5.3956 0.1853

11 5/8 0.7371 1.3567 0.1313 7.6177 5.5135 0.1814

11 3/4 0.753 1.328 0.1341 7.4565 5.6327 0.1775

11 7/8 0.7691 1.3002 0.137 7.3003 5.7532 0.1738

12 0.7854 1.2732 0.1399 7.149 5.8749 0.1702

12 1/8 0.8018 1.2471 0.1428 7.0024 5.998 0.1667

12 1/4 0.8185 1.2218 0.1458 6.8602 6.1223 0.1633

12 3/8 0.8353 1.1972 0.1488 6.7223 6.2479 0.1601

12 1/2 0.8522 1.1734 0.1518 6.5885 6.3747 0.1569

12 5/8 0.8693 1.1503 0.1548 6.4587 6.5028 0.1538

12 3/4 0.8866 1.1279 0.1579 6.3327 6.6323 0.1508

12 7/8 0.9041 1.1061 0.161 6.2103 6.7629 0.1479

DISPLACEMENT & CAPACITY

8/20/2019 BlkMax


OD

(in)

ID

(in)

NOMINALWEIGHT

(lb/ft)

STEELDISPLACEMENT

(gal/ft)

CAPACITY

(gal/ft)

2 3/8 1.815 6.65 0.10542 0.13440

2 7/8 2.151 10.40 0.16674 0.18858

3 1/2 2.764 13.30 0.21084 0.31164

3 1/2 2.602 15.50 0.24486 0.27636

4 3.340 14.00 0.23100 0.455284 1/2 3.826 16.60 0.27510 0.59724

4 1/2 3.640 20.00 0.32676 0.54054

5 4.276 19.50 0.31500 0.74592

5 4.000 25.60 0.39144 0.65268

STANDARD HEAVY-WALLDRILLPIPE PROPERTIES

8/20/2019 BlkMax


NominalSize(in.)

PipeID

(in.)

NominalWeight(lb./ft.)

Tool JointConnection

3 1/2 2.063 25.3 3 1/2 IF or NC 38

4 2.563 29.7 4 FH or NC 40

4 1/2 2.750 39.9 4 IF or NC 46

5 3.000 48.5 4 1/2 IF or NC 50

SPIRAL-WATETM HEAVY-WALLDRILLPIPE PROPERTIES

NominalSize(in.)

PipeID

(in.)

NominalWeight(lb./ft.)

Tool JointConnection

3 1/2 2.125 28.3 3 1/2 IF or NC 38

4 2.563 33.8 4 FH or NC 404 1/2 2.750 44.0 4 IF or NC 46

5 3.000 55.3 4 1/2 IF or NC 50

5 1/2 3.250 63.0 5 FH

6 5/8 5.000 57.0 6 5/8 FH

8/20/2019 BlkMax


NOZZEL FLOW AREAS(IN2)

Nozzle Size 1 2 3 4 5 6 7 8 9 10

8/20/2019 BlkMax


(32nds)1 2 3 4 5 6 7 8 9 10

17 .221 .442 .663 .884 1.105 1.326 1.547 1.768 - -

18 .249 .498 .747 .996 1.245 1.494 1.743 - - -

20 .307 .614 .921 1.228 1.535 - - - - -

22 .371 .742 1.113 1.484 - - - - - -

24 .441 .882 1.323 1.764 - - - - - -

26 .519 1.038 1.557 - - - - - - -

28 .601 1.202 - - - - - - - -

30 .690 1.380 - - - - - - - -

1” .785 1.570 - - - - - - - -

1 1/8” .994 - - - - - - - - -

1 1/4” 1.227 - - - - - - - - -

MUD WEIGHT

lb/gal lb/ft3 kg/m3

Specific

Gravity

Gradient

Depth

(psi/ft)

Gradient

Depth

(kPa/m) lb/gal lb/ft3 kg/m3

Specific

Gravity

Gradient

Depth

(psi/ft)

Gradient

Depth

(kPa/m) lb/gal lb/ft3 kg/m3

Specific

Gravity

Gradient

Depth

(psi/ft)

Gradient

Depth

(kPa/m)

8/20/2019 BlkMax


8.34 62.38 999.3 1 0.434 9.8

8.5 63.58 1018.5 1.02 0.442 10

8.6 64.32 1030.5 1.03 0.447 10.1

8.7 65.07 1042.4 1.04 0.452 10.2

8.8 65.82 1054.4 1.05 0.458 10.4

8.9 66.57 1066.4 1.07 0.463 10.5

9 67.31 1078.4 1.08 0.468 10.6

9.1 68.06 1090.4 1.09 0.473 10.7

9.2 68.81 1102.3 1.1 0.478 10.8

9.3 69.56 1114.3 1.12 0.484 10.9

9.4 70.31 1126.3 1.13 0.489 11.1

9.5 71.05 1138.3 1.14 0.494 11.2

9.6 71.8 1150.3 1.15 0.499 11.3

9.7 72.55 1162.3 1.16 0.504 11.4

9.8 73.3 1174.2 1.18 0.51 11.5

9.9 74.05 1186.2 1.19 0.515 11.6

10 74.79 1198.2 1.2 0.52 11.8

10.1 75.54 1210.2 1.21 0.525 11.9

10.2 76.29 1222.2 1.22 0.53 12

10.3 77.04 1234.2 1.24 0.536 12.1

10.4 77.79 1246.1 1.25 0.541 12.2

10.5 78.53 1258.1 1.26 0.546 12.4

10.6 79.28 1270.1 1.27 0.551 12.5

10.7 80.03 1282.1 1.28 0.556 12.6

10.8 80.78 1294.1 1.29 0.562 12.7

10.9 81.53 1306 1.31 0.567 12.8

11 82.27 1318 1.32 0.572 12.9

11.1 83.02 1330 1.33 0.577 13.1

11.2 83.77 1342 1.34 0.582 13.2

11.3 84.52 1354 1.36 0.588 13.3

11.4 85.27 1366 1.37 0.593 13.411.5 86.01 1377.9 1.38 0.598 13.5

11.6 86.76 1389.9 1.39 0.603 13.6

11.7 87.51 1401.9 1.4 0.608 13.8

11.8 88.26 1413.9 1.41 0.614 13.9

11.9 89.01 1425.9 1.43 0.619 14

12 89.75 1437.8 1.44 0.624 14.1

12.1 90.5 1449.8 1.45 0.629 14.2

12.2 91.25 1461.8 1.46 0.634 14.4

12.3 92 1473.8 1.48 0.64 14.5

12.4 92.74 1485.8 1.49 0.645 14.6

12.4 92.74 1485.8 1.49 0.645 14.6

12.5 93.49 1497.8 1.5 0.65 14.7

12.6 94.24 1509.7 1.51 0.655 14.8

12.7 94.99 1521.7 1.52 0.66 14.912.8 95.74 1533.7 1.53 0.666 15.1

12.9 96.48 1545.7 1.55 0.671 15.2

13 97.23 1557.7 1.56 0.676 15.3

13.1 97.98 1569.6 1.57 0.681 15.4

13.2 98.73 1581.6 1.58 0.686 15.5

13.3 99.48 1593.6 1.6 0.692 15.6

13.4 100.22 1605.6 1.61 0.697 15.8

13.5 100.97 1617.6 1.62 0.702 15.9

13.6 101.72 1629.6 1.63 0.707 16

13.7 102.47 1641.5 1.64 0.712 16.1

13.8 103.22 1653.5 1.65 0.718 16.2

13.9 103.96 1665.5 1.67 0.723 16.4

14 104.71 1677.5 1.68 0.728 16.514.1 105.46 1689.5 1.69 0.733 16.6

14.2 106.21 1701.5 1.7 0.738 16.7

14.3 106.96 1713.4 1.72 0.744 16.8

14.4 107.7 1725.4 1.73 0.749 16.9

14.5 108.45 1737.4 1.74 0.754 17.1

14.6 109.2 1749.4 1.75 0.759 17.2

14.7 109.95 1761.4 1.76 0.764 17.3

14.8 110.7 1773.3 1.78 0.77 17.4

14.9 111.44 1785.3 1.79 0.775 17.5

15 112.19 1797.3 1.8 0.78 17.6

15.1 112.94 1809.3 1.81 0.785 17.8

15.2 113.69 1821.3 1.82 0.79 17.9

15.3 114.44 1833.3 1.84 0.796 1815.4 115.18 1845.2 1.85 0.801 18.1

15.5 115.93 1857.2 1.86 0.806 18.2

15.6 116.68 1869.2 1.87 0.811 18.3

15.7 117.43 1881.2 1.88 0.816 18.5

15.8 118.18 1893.2 1.9 0.822 18.6

15.9 118.92 1905.1 1.91 0.827 18.7

16 119.67 1917.1 1.92 0.832 18.8

16.1 120.42 1929.1 1.93 0.837 18.9

16.2 121.17 1941.1 1.94 0.842 19.1

16.3 121.91 1953.1 1.96 0.848 19.2

g g y (p ) ( )

16.4 122.66 1965.1 1.97 0.853 19.3

16.5 123.41 1977 1.98 0.858 19.4

16.6 124.16 1989 2 0.863 19.5

16.7 124.91 2001 2.01 0.868 19.616.8 125.65 2013 2.02 0.874 19.8

16.9 126.4 2025 2.03 0.879 19.9

17 127.15 2036.9 2.04 0.884 20

17.1 127.9 2048.9 2.05 0.889 20.1

17.2 128.65 2060.9 2.06 0.894 20.2

17.3 129.39 2072.9 2.08 0.9 20.3

17.4 130.14 2084.9 2.09 0.905 20.5

17.5 130.89 2096.9 2.1 0.91 20.6

17.6 131.64 2108.8 2.11 0.915 20.7

17.7 132.39 2120.8 2.12 0.92 20.8

17.8 133.13 2132.8 2.14 0.926 20.9

17.9 133.88 2144.8 2.15 0.931 21.118 134.63 2156.8 2.16 0.936 21.2

18.1 135.38 2168.8 2.17 0.941 21.3

18.2 136.13 2180.7 2.18 0.946 21.4

18.3 136.87 2192.7 2.2 0.952 21.5

18.4 137.62 2204.7 2.21 0.957 21.6

18.5 138.37 2216.7 2.22 0.962 21.8

18.6 139.12 2228.7 2.23 0.967 21.9

18.7 139.87 2240.6 2.24 0.972 22

18.8 140.61 2252.6 2.26 0.978 22.1

18.9 141.36 2264.6 2.27 0.983 22.2

19 142.11 2276.6 2.28 0.988 22.3

19.1 142.86 2288.6 2.29 0.993 22.519.2 143.61 2300.6 2.3 0.998 22.6

19.3 144.35 2312.5 2.32 1.004 22.7

19.4 145.1 2324.5 2.33 1.009 22.8

19.5 145.85 2336.5 2.34 1.014 22.9

19.6 146.6 2348.5 2.35 1.019 23.1

19.7 147.34 2360.5 2.36 1.024 23.2

19.8 148.09 2372.4 2.38 1.03 23.3

19.9 148.84 2384.4 2.39 1.035 23.4

20 149.59 2396.4 2.4 1.04 23.5

PREFIXES

Multiplying Factor Prefix

Symbol

8/20/2019 BlkMax


1 000 000 = 106 mega M

1 000 = 103 kilo k

100 = 102 hecto h

10 = 101 deca da

0.1 = 10-1 deci d

0.01 = 10-2 centi c

0.001 = 10-3 milli m

0.000 001 = 10-6 micro µ

CONVERSIONS

UNITS MULTIPLY BY TO OBTAIN

ac 43560 ft2

4047 2


ft 1.89394 x 10-4 mift2 0 0929 2

8/20/2019 BlkMax


ac 4047 m2

ac 0.001562 mi2

atm 33.94 ft of water atm 14.7 lb/in2

atm 1.013 x 105 pascalsatm 1.033 kg/cm2

bbl (British, dry) 5.78 ft3

bbl (British, dry) 0.1637 m3

bbl (British, dry) 36 gal(British)bbl, cement 170.6 kg

bbl, cement 376 lb(cement)bbl, oil 42 gal (U.S.)bbl (U.S., liquid) 4.211 ft3

bbl (U.S., liquid) 0.1192 m3

bbl (U.S., liquid) 31.5 gal (U.S.)bbl/min 42 gal/minbbl/day 0.02917 gal/mincm3 3.531 x 10-5 ft3

deg (angle) 60 mindeg (angle) 0.01745 raddeg (angle) 3600 sdeg/s 0.1667 rpmdeg/s 2.778 x 10-3 rev/sdaN 2.2467 lbsft 12 inft 0.3048 m

ft2 0.0929 m2

ft3 1728 in3

ft

3

0.02832 m

3

ft3 7.481 gal (U.S.)ft3 28.32 litersft3 of water (60 deg. F) 62.37 lbft3/min 4.72 x 10-4 m3/sft3/min 0.1247 gal/sft3/min 0.472 liters/sft3/s 448.83 gal/minft3- atm 2116.3 ft-lb

ft-lb 1.286 x 10-3

Btuft-lb 0.1383 Kg-mft-lb 1.355818 N mft/min 0.508 cm/sft/min 0.01667 ft/sft/min 0.01829 km/hr ft/min 0.3048 m/minft/min 0.01136 mi/hr ft-lb/min 0.01667 ft-lb/sft-lb/min 2.26 x 10-5 KWft-lb/s 1.356 x 10-3 KWft-lb/s 1.818 x 10-3 hpg 0.001 kggal (British) 1.20094 gal (U.S.)gal 3785 cm3

gal 0.1337 ft3

gal 231 in3

CONVERSIONS


gal 3.785 litersgal/min 2 228 x 10-3 ft3/s


lb/gal .1198 g/cm3

lb/in2 6 894757 kPa

8/20/2019 BlkMax


gal/min 2.228 x 10 3 ft3/sgal/min 3.785 liters/min

g-cm

2

3.4172 x 10

-4

lb-in

2

hp 0.7457 kWin 25.4 mmin2 645.2 mm2

in2 6.452 cm2

in2 6.944 x 10-3 ft2

in3 1.639 x 10-5 m3

in3 5.787 x 10-4 ft3

in3 4.329 x 10-3 gal

in3

0.01639 literskg 2.2046 lbkg-m 7.233 ft-lbkg/m3 0.06243 lb/ft3

kg/m 0.672 lb/ftkW 44250 ft-lb/minkW-hr 2.655 x 106 ft-lblb 4.45 x 105 dyneslb 4.448 newtonslb 4.535 x 10-4 tons(metric)lb/ft3 16.02 kg/m3

lb/ft3 5 787 x 10-4 lb/in3

lb/in2 6.894757 kPaliter 0.03531 ft3

liter 0.001 m

3

liter 0.2642 galm 3.2808 ftm2 10.764 ft2

m3 264.2 galm3/s 15850 gal/minm3/s 60000 liters/minmi 2 2.788 x 107 ft2

mi 2 2.59 km2

rad 57.3 degrad/s 0.1592 rev/srad/s 9.549 rpmtemp. (°C) 1.8 (°C)+32 temp.°Ftemp. (°F) (°F - 32) 5/9 temp.°Ctons (metric) 1000 kgwatts 0.7376 ft-lb/swatts 1.341 x 10-3 hpyds 3 ftyds 0.9144 m

Date post:	07-Aug-2018
Category:	Documents
Upload:	kevin-mueller
View:	213 times
Download:	0 times

BlkMax

Documents