BM20200 Mobile Brake tester

The perfect choice if you are looking for... • A mobile roller brake tester for vehicles with axle loads up to 20 T.

• Proven quality from more than 500 units delivered worldwide since release of BM20200 in 1995.

• 10 minutes setup time by one person.

2

BM20200 is a Mobile Roller Brake Tester, MRBT, for test of all vehicles up to a maximum axle load of 20.000 kg. As standard the BM20200 can be powered by only 3 x 400 VAC + N + G at 25 Amps, which in practice equals a 25 KVA generator.

The BM20200 is approved by several international authorities (such as RWTÜV Germany and BIVV Belgium), complies with the ISO standard, and holds a NATO number.

The BM20200 MRBT is equipped with the same electronics and software as the BM in-ground RBT’s BM12200, BM14200 and BM17200 and therefore the BM20200 offers the same high test standard and data processing as these in-ground models.

As for the BM in-ground brake testers, the BM20200 can optionally be supplied with a long range of features which allows for a customization, that meets the exact customer requirements:

• Infrared remote control system.• PDA display and remote control.• Radio air pressure system (RTS).• Diagnostic printout with and without link to PC with BM

FlexCheck software.• Automatic axle weighing and vehicle total weight.• Tachograph calibration on BM brake tester (11 kW gear

motors 2.0 km/h).• Test of 4x4, 4x6 and 6x8 drive vehicles.• Test vehicles with a high variation of wheel bases up to

4000 mm.• Conventional axle load simulation.• Can be placed directly on the floor indoor or outdoor

without need of civil work.

BM20200 Mobile Roller Brake Tester

3

Compared to other mobile roller brake testers, the BM20200 has the following unique features:

Unique features

Low floor space requirementDue to the low height of the rollerset, the length of the ramps are only 1.25 meter on each side i.e. a total setup length of only 3.5 meter.

Extremely low clearanceThe rollerset height is only 160 mm, which ensures against bottom out when passing with very low vehicles such as coaches and cars.

The BM20200 design is simple

with strong and flexible mechanical solutions. The

benefit is that there are no particular requirements to the testing area surface. The BM20200 can be placed on asphalt or

concrete floor, but also on uneven gravel ground,

sand and dirt.

Insensitive to testing area surface

4

Display on trolley The display can be delivered on a trolley with a robust network cable of up to 100 meters. Hereby the display can be placed a convenient long distance from the rollerbed and hereby be monitored even when the last axle of a vehicle combination is tested.

Axle Load SimulationThe BM20200 can optionally be supplied with an Axle Load Simulation system, which can simulate up to 8 ton. The system can be supplied with a compressed air powered foot pump or an integrated electrical power unit.

Handheld PDA control and BM FlexCheck softwareThe BM20200 can be supplied with a PC Windows program, BM FlexCheck, which can be installed on a PC table integrated with a BM20200.

In conjunction with BM FlexCheck, the BM20200 can be supplied with a handheld PDA unit which communicates wirelessly (WLAN) with the BM20200. The PDA has a virtual display which shows all the readings of the brake test and together with the integrated touch screen based remote control feature, the operator can fully control the brake test from the PDA unit in all situations.

5

Practical advantages of the PDA unit In many applications, the location of the traditional physical display or traditional PC console prevents an optimal use of the brake tester by the operator. One reason can be that vehicle cabin passes the display or PC console when testing the last axles of the vehicle and trailer - a problem which has increased due to introduction of long modular vehicle combinations. Another reason can be that vehicles needs to be reversed over the brake tester in non-drive through lanes, and then the operator cannot see the Display or PC console.

The PDA is a solution to these problems and can easily be stored in a jacket pocket when not used.

Operator brake test guide - BMAssist Another distinct feature of the PDA unit compared to a traditional infrared remote control is the integrated BM Assist, which is a menu based software that guides the operator safely and correctly through the complete brake test. BM Assist is available both on the PDA unit and PC program.

PC tableThe BM20200 can be supplied with an integrated PC table and power connectors, so a PC notebook can be placed directly next to the brake tester.

Together with a printer placed inside the integrated printer cabinet, the operator has a full “office” environment onboard the BM20200.

Expanding BM20200 into an On-ground Test Line

This test lane concept can be further expanded with speedometer BM605.

The BM20200 can be used in conjunction with the hydraulic BM53000 mobile play detector with capacity of testing axle loads up to 20 Ton.

The additional on-ground test equipment has the same height (approx. 160 mm) as BM20200 and they can therefore share the drive on and off ramps.

The additional on-ground equipment can optionally be supplied with integrated wheels and the operator can therefore move this equipment around as easy as the BM20200. Complete setup time for one person is less than 15 minutes.

Both the BM20200 brake tester and the BM53000 wheel play detector can easily be town to their correct positions or stored by one person.

6

Since the BM20200 can be completely folded up and minimized sizewise several means of customized transport options can be offered:

BM Trailer solutionBM has developed a unique transport frame system, which can be mounted onto a standard trailer with tilt function. The transport system is modularly designed and covers means of transportation of generator, BM20200 brake tester, BM53000 wheel play detector and BM901 side slip meter including electrical winches and battery.

Roadside enforcement by VOSA - Great Britain.Remote Periodic Technical Inspection by VTNZ - New Zealand.

Flexible means of transportation

The transport system has a number of important benefits including ensuring equal distribution of weight onto the full area of the trailer bed, fixation of equipment during transport and correct angle for avoiding bottom out when loading and unloading the equipment.

Trailer parked. Towing vehicle arrives to site and trailer is opened. Trailer is tilted and ramp is folded down.

Special unload rails are placed and equipment is rolled down using the integrated electrical winch.

The BM53000 wheel play detector unit is rolled down using the electrical winch. Rails are then moved to the top of the transport rail system whereafter the BM20200 mobile brake tester is rolled down using the electrical winch.

Both the BM20200 and BM52000 are supplied with small wheels so one person can easily place the equipment on the preferred location for vehicle testing.

1 2 3

7654

7

Container solutionBM can supply a 20’ container solution with purpose built rails for load/unload and special storage design inside the container. Following shows the management and setup

of BM20200 when transported in a 10’ container. Note the special rails used for rolling the BM20200 in and out of the container.

2 3 41

The drive on and off ramps are quickly fitted to the equipment without use of tools.

The equipment has strong feet with high resistant contact path. All feet can be adjusted in height to offset uneven ground.

The equipment is connected to - and powered from - the onboard generator located inside the trailer.

Final adjustments before vehicle is called forward. Approximate setup time for two persons is 5-10 minutes.

First axle of the vehicle is being tested on the BM20200 mobile roller brake tester.

The vehicle is driven forward so the first axle is on top of the BM53000 wheel play detector. The operator uses a remote control to move the hydraulically powered plates and detect for steering system problems such as wear etc.

8 9 10

131211

Customer: US Army in Afghanistan.

HIGH QUALITY VEHICLE TEST EQUIPMENT

BM Autoteknik A/SErhvervsparken 7DK-9632 MøldrupDenmarkTel.: +45 8669 2022

Visit us at www.bmtest.dk ...to find more info about BM Autoteknik A/S

Texts and photos may present optional equipment available at additional cost. All functionality, features, specifications and other product information provided in this document including, but not limited to, the benefits, design, pricing, components, performance, availability, and capabilities of the product are subject to change without notice or obligation. BM

2020

0.B0

001.

02.V

02, 0

6 - 2

012

Worldwide supplier of Mobile Vehicle Inspection Test Equipment

USA

US Army Afghanistan

VOSA - UK

Australia VTNZ - New Zealand

Kazakhstan

Police - SwedenGOCA - Belgium

KenyaPolice - Switzerland

ApprovalsBM Autoteknik A/S is proud to have obtained approvals for the BM20200 mobile roller brake tester in the following countries:

• TÜV Germany• BIVV Belgium• GEA England• NZTA New Zealand• Russia and Kazakhstan

BM20200 is in compliance with ISO21069

Technical data for BM20200 mobile brake testerDescription DimensionRoller bed L x W x H 3465 x 4240/4740 x 505 mmRoller diameter and length 150 mm, 1000/1250 mmFriction coefficient of roller from factory dry/wet Min 0.7/0.6Wheel span (can be customized) 800 to 2800/3300 mmDistance between roller centers 430 mmMaximum test axle weight 16000/20000 kgGearmotor size 4.8/11/15 kWMax brake force measurement 0 – 4000/6000 daN Test speed 1.0/2.0/2.0 km/hDisplay L x W x H 930 x 820 x 100 mmControl box L x W x H 600 x 600 x 210 mmDisplay brake force scale 0 – 4000/6000 daN Brake force measuring accuracy 0 – 100 daN : ± 2 daN

-> 100 daN : ± 2% FSPedal force measurement accuracy 0 – 100 daN : ± 1 daNPower and fuses 3 x 400 VAC + N + E

Minimum 25/63/80 Amp

BM53000

Products Company Find distributor

News & Press

Products Heavy vehicles Play detector BM53000

BM53000 Click to view

Features

The BM53000 is a hydraulic wheel play detector for light and heavy vehicles, busses and coaches up to 20.000 kg axle load. It consist of two strong steel plates - one for each wheel - which are installed into the floor. The plates are moved horizontally in 8 different directions by means of a remote control. The remote control features both an integrated flash light functionality and a keypad to control each movement of the plates.

The operator can choose to control each movement manually, automatically in selcected directions, or to activate a 10 cycle 'box movement' sequence. All automatic movements are stopped by pressing any key on the remote control unit.

The power unit is installed in the pit either at the end or inside an excess in the wall of the inspection pit. Advantages and benefits

The BM53000 checks the steering and suspension system of the vehicle without need of jacking up the axle. The operator will be able to detect worn kingpin bushings, loose tie-rod ends, broken welds, loose fasteners and other failed components. The remote control unit can be supplied with either cable or radio link to the control system. Selecting radio link has the advantage, that the operator is not restricted in his work and the option avoids expensive downtime due to cable damages. Applications

The BM53000 is usually installed over an inspection pit and used both by repair work shops and vehicle inspection bodies.

Heavy vehicles

Roller brake tester

Play detector

BM53000

BM52000 mobile

Tacho tester

Radio system for air pressure measurement

PC Software and PDA unit

Load Simulation System

Light vehicles

Mobile/On-ground equipment

Motorcycle & scooter 30-45

Armed forces

BM FlexCheck IT concept

Documentation

<< back Top

BM Autoteknik A/S | Erhvervsparken 7 | 9632 Møldrup | Denmark | Phone: +45 8669 2022 | Fax: +45 8669 2199 | Email: Write

http://bmtest.dk/Default.aspx?ID=1453 [25/10/2012 10:12:01 a.m.]

BM Emission testersBM3101 - BM3201

The perfect choice if you are looking for... • Accurate and consistent measurements. • Latest technology and software meeting authority requirements. • Robustness with long lifetime and low maintenance cost.

2

BM Emission testers

BM3201 4 Gas analyser• Graphic screen and 5 key keyboard.• Guided test procedure on LCD

display and PDA unit.• Thermal integrated printer

(or Matrix Dot on demand).• Intelligent control of gas pump via

PDA to ensure long pump lifetime.• Compatible with the OIML R99 Class

0 and ISO 3930 standards.• Multi-gas analysis mode.• Vehicle inspection mode.• Guided test procedure on LCD

display and PDA unit.• Automatic condensation extraction.

Technical dataEffective length of the measuring chamber

215 mm ±0.05 cm

Preheating time From 3 to 6 min depending on ambient temperature

Zero adjustment and calibration before use

Automatic

Control of zero adjustment Automatic by electrical filter centred at 50%

Humidity 30% to 90%

Temperatures Ambient temp. range for operation +5 to +40°C

Storage temp. -32°C to +55°C

Measurement range of the measured value

Opacity

Resolution

0.00 to 9.99 m-1

0.01 m-1

Maximum relative error under standard conditions

• Temperature +20 °C• Atmospheric pressure 1013 hPa

• Relative humidity 60% ±15% • Opacity error below 0.15 m-1

Measurement range of influencing factors (which allows correction of the opacity value)

Temperature of the gas being measured

0-256 C (resolution 1°C)

Physical response time 10% to 90%

Less than 0.2 sec. for gas at 75L/min

Electrical response time 0.9 sec

Power supply 1.5 A / 115 VAC 0.9 A / 230 VAC (+10% -15%)

50-60 Hz (±2%)

• Graphic screen and 5 key keyboard.

• Guided test procedure on LCD display and PDA unit.

• Thermal integrated printer (or Matrix Dot on demand).

• It is in complete compliance with the opacity control procedure for vehicle inspection centres and with the procedure for determining the opacity applicable to repair workshops.

• Linearity check.

BM3201 Smoke tester

BM Autoteknik A/S offers a complete and coherent line of solutions: headlight testers, EOBD scantools, test lane and emission testing systems. The BM3201 range includes changing automobile technology, it is both an antipollution control tool (gas analyser & smokemeter) and a diagnostic tool. The BM3201 range can be supplied with handheld Bluetooth based PDA units, which allow the operator to operate the emission tester from inside the vehicle.

Technical dataPreheating time < 5 minutes at 20°C (1 minute minimum)

Response time 13 seconds for HC, CO, CO2, 28 seconds for oxygen (transition from 20.9% to 0.1% for a gas with 0% O2)

Nominal pump delivery 6 l/min.

Minimum pump delivery 3.5 l/min.

Air pressure variation Automatic correction by integrated absolute pressure sensor

Zero point and sensitivity

Automatic compensation

Automatic pump standby and automatic zeroing

Measurement ranges Accuracy Resolution

HC Normal resolution: 0 to 20000 ppm Propane

10 ppm Normal res.: 10 ppm vol.High res.: 1 ppm vol.

CO -0.03 à 10.5 % 0.03 %* Normal res.: 0.01 % vol.High res.: 0.001 % vol.

CO2 -0.4 à 21.0 % 0.5 %* Normal res.: 0.1 % vol.

O2 -0.5 à 21.7 % 0.1 %* If O2<4 % vol. high res.: 0.01 % vol.Otherwise normal res.: 0.1 % vol.

Nox 0 à 5000 ppm N/A 1 ppm vol.

Engine speed 0 à 9999 RPM +- 10 RPM 1 tours/min

Oil temperature -5 à 150 °C +- 1 °C 1 °C

Corrected CO 0 à 10 % 0.03 % 0.01 %

Air/fuel coefficient (Lambda)

0.600 to 1.200 0.03 0.001 or 0.01, selectable

* Absolute or 5 % of the value read.

3

BM3201 Combined emission tester• Graphic screen and 5 key

keyboard.• Guided test procedure on LCD

display and PDA unit.• Thermal integrated printer (or

Matrix Dot on demand).• Intelligent control of gas pump

via PDA to ensure long pump lifetime.

• Petrol and diesel rev-counter.

Pipe extension for high exhaust smoke tests

BM4220 EOBD scantoolThe scantool is a tool that gives access to internal data from on-board systems. It is connected to the vehicle’s OBDII auto diagnostic port and scans the stored data and current data available using one of the 5 standard protocols: J1850 PWM, J1850 VPW, ISO9141-2, ISO14230-1,2, ISO15765 and J1939.• Multi-make and easy to use.• Access to measurements made by the calculator

(RPM, speed, pressure, temperature, advance, ...).• Readings and launch of the tests: catalyst, EGR, O2 sensor.• Stored fault codes (injection, emissions, ...).• Reinitialisation of fault codes.• Bluetooth.

Covers almost all vehicle types: Petrol, Diesel, GLP / LDV, HDV, 2-wheelers. The unit provides Guided test procedure on LCD display.• Keyboard for cylinder selection

and mode settings.• Cables for battery clamps, cigar

lighter and vibration sensor.• Oil temperature probe.• Lithium battery and charger.

BM8530 RPM & Temperature unit

Technical data

Automatic initialisationMeasurement range 400 - 9 999 rpmMaximum error <20 rpm at speeds below 2000 rpmResolution 10 RPM and 1°C

<2 % in other cases-13°C to 150 °C (oil temperature).

Oil temperature +/- 1°C.Response time <1 secondMeasurement update rate 10 times per secondInitialisation time <17 seconds

BM3101 Smoke meterBM can offer a cost effective smoke meter solution, which only consist of the measuring head unit and a PDA with software that guides the operator through the test. The measuring head transfers all data to the PDA unit via Bluetooth and all measured and calculated data is shown on the PDA unit. Optionally this model can be supplied with a Bluetooth printer solution, where the data is printed in a simple format. This equipment is available in selected countries only.

BM has developed a special pipe solution for testing heavy vehicles with high tail exhaust pipes. The solution removes the need of ladders or other lifting gear, as the operator can easily place the measuring probe into the exhaust pipe while standing on the floor.

The solution is designed so the smoke meter can remain on the floor instead of having to be lifted. The solution thus meets work requirements from many national Health and Safety Authorities.

HIGH QUALITY VEHICLE TEST EQUIPMENT

BM Autoteknik A/SErhvervsparken 7DK-9632 MøldrupDenmarkTel.: +45 8669 2022

BM E

mis

sion

test

er.B

0001

.02.

V02,

03

- 201

2

Visit us at www.bmtest.dk

...to see our wide product range of test equipment

Texts and photos may present optional equipment available at additional cost. All functionality, features, specifications and other product information provided in this document including, but not limited to, the benefits, design, pricing, components, performance, availability, and capabilities of the product are subject to change without notice or obligation.

Integration with BM FlexCheck

BM emission testers are prepared for integration with the BM FlexCheck vehicle inspection IT system, which allows for establishing fully automated one or multilane test facilities.

One of the unique advantages of BM FlexCheck is that the test equipment of a multilane station can be shared across the lanes - including BM emission and headlight testers. This way a multilane test facility can have more lanes with less test equipment whereby a significant reduction in capital investment can be obtained.

Automatic data transfer via Bluetooth from BM3101 and BM3201 to BM FlexCheck vehicle inspection IT system.

BM Headlight testersBM2100 - BM2500 - BM2600

The perfect choice if you are looking for... • Accurate and consistent measurements. • Latest technology and software meeting authority requirements. • Robustness with long lifetime and low maintenance cost.

2

IntroductionThe headlight tester range from BM Autoteknik A/S includes three kinds of devices:• Mechanical BM2100.• Electronic photodiode BM2500.• Electronic camera BM2600.

BenefitsThis line has the following benefits:• Simple, intuitive and quick to use.• Easy to handle thanks to the counter-weighted raising and lowering

system.• Robust mechanics with superior stability needed for precision

measurement.• A total weight of 25 kg, making it easy to move.• Able to adjust and control all types of lamps (Halogen, Xenon and Leds).• Powerful and timed lateral positioning laser with stand by function.• Wheels mounted on bearings, guaranteeing the accuracy of measurements

over time.• Capacity to adapt to current national standards and available in the

country’s language.• Availability and reactivity of the support teams: remote maintenance,

hotline, training, updating of appliances, maintenance software.

BM Headlight testers

BM2500

The BM2500 is an excellent compromise between economyand efficiency. It has the following features :• Patented electronic photodiode measurement system.• Easy to use thanks to its positioning assistance.• High autonomy for over 100 inspections.• Data transmission.• Accurate measurement of the beam angle.• Available in garage mode for headlamp adjustment.

BM2100

The BM2100 is specially designed for applications that donot need data transmission and for which a visual control issufficient.• Mechanical headlight tester.• Economical and robust product.

3

The BM2600 is an electronic headlight tester with camera based on the most advanced technology.• Measurement and adjustment of low beam high and fog

lamps.• Used to automatically and quickly control and measure

the pitch angle, yaw angle, break point, roll angle light intensity and dazzling.

• Suitable to all types of vehicle (European, American and Japanese).

• Compatible with both left and right hand drive.• Easy to use thanks to its positioning assistance.• Data transmission using all types of protocols.• Simple, user friendly interface on a colour touch screen.

BM2600

BM2100 BM2500 BM2600Dipped beam lampsBeam angle measurement Lateral angle measurement Intensity measurement – Dazzling measurement –

Main beam lampsBeam angle measurement Lateral angle measurement Intensity measurement –

Fog lampsBeam angle measurement Lateral angle measurement – Intensity –

Computer linksRS 232 cable connections – Wireless (bluetooth) – Contact us for protocols – PRINTING –

EquipmentBattery option – OptionPositioning laser Electronic positioning assistance – Counter-weighted raising and lowering system

Technical specifications

Options selection• Wheel base• Rail base

• Bluetooth• HGV

Compliance• R48 recommandation• CE Conformity

Visual Diagnosic OK

3

RS 232 /Bluetooth printer Protective cover Handle

Options

HIGH QUALITY VEHICLE TEST EQUIPMENT

BM Autoteknik A/SErhvervsparken 7DK-9632 MøldrupDenmarkTel.: +45 8669 2022

BM H

eadl

ight

test

ers.B

0001

.02.

V01,

02

- 201

2

Visit us at www.bmtest.dk

...to see our wide product range of test equipment

Texts and photos may present optional equipment available at additional cost. All functionality, features, specifications and other product information provided in this document including, but not limited to, the benefits, design, pricing, components, performance, availability, and capabilities of the product are subject to change without notice or obligation.

Integration with BM FlexCheck

BM headlight and emission testers are prepared for integration with the BM FlexCheck vehicle inspection IT system, which allows for establishing fully automated one or multilane test facilities.

One of the unique advantages of BM FlexCheck is that the test equipment of a multilane station can be shared across the lanes - including BM headlight and emission testers. This way a multilane test facility can have more lanes with less test equipment whereby a significant reduction in capital investment can be obtained.

Automatic data transfer via Bluetooth from BM2500 and BM2600 to BM FlexCheck vehicle inspection IT system.

BM Windows software and PDA system

Products Company Find distributor

News & Press

Products Heavy vehicles PC Software and PDA unit

BM Windows software and PDA systemBM offers dedicated windows programs for both Heavy Vehicle and Light vehicle brake testers. When a windows program is connected to your BM equipment, then you can additional purchase the BM PDA system. The PDA system consist of a PDA with BM software, which communicate with the windows program using WLAN technology (radio linked). The PDA will perform as a unque remote control using the tochscreen of the PDA. The layout of the remote control is identical to the normal Infra Red remote control unit for BM equipment. Additionally, the PDA also perform as a virtual display, which shows you all the same data, as you find on the physiscal BM display. Benefits of BM PDA system

● If your workshop is designed, so you pass the display when testing for instance semi-trailers, then the PDA is a unique solution, as it provide you with a remote control and display inside the cabin.

● If you purchase the option bi-directional, because you do not have a drive-through lane, you will often find it inconvinient, that you cannot see the display or use the remote control, when testing in opposite direction. The PDA solve this problem completely, as it provides you with a remote control and display.

● If you purchase a mobile brake tester, the PDA can be a very usefull, as it at all times gives you acesss to both a remote control and display inside the vehicle.

Additionally, you will experience, that today a PDA can be used for many other applications in the workshop. BM Autoteknik A/S already offers the BM FlexCheck system, which allows you to perform quality control, vehicle inspection, pre-inspection and reception procedures from the PDA. You will find, that other equipment suppliers to the workshop industry has also developed tools and solutions based on the PDA unit. The following shortly describes the various Windows programs for BM heavy vehicle brake testers. BM also offers a fully integrated vehicle inspection IT system, BM FlexCheck, designed for vehicle inspection bodies.

Heavy vehicles

Roller brake tester

Play detector

Tacho tester

Radio system for air pressure measurement

PC Software and PDA unit

Load Simulation System

Light vehicles

Mobile/On-ground equipment

Motorcycle & scooter 30-45

Armed forces

BM FlexCheck IT concept

Documentation

http://bmtest.dk/Default.aspx?ID=19 (1 of 4) [25/10/2012 10:27:09 a.m.]

BM Windows software and PDA system

Virtual Display Virtual radio remote control Real time graphics

1. Brake Perfect Windows

This program is an option to BM brake testers for heavy vehicles: BM20200, BM17200, BM13200 and BM12200. The program offers basic features such as collection of test data, SQL database and various printout possibilities. Additional powerful diagnostic tools are implemented:

● Matching of brake performance of different vehicles for instance tractor and trailer

● Graphical presentation of all test results

● Effective zoom features ● Repair and comment features

Brake Perfect windows has been customised with special user-friendly printouts, which allow you to increase your revenue on each vehicle arriving to your workshop.

2. VOSA Database Manager

The VOSA Database Manager is a Windows 2000/XP based program that utilizes the authorized vehicle database from the VOSA and ensures that the brake test results are processed correctly. Printout is designed according to the VOSA format and operates on the DtP number of the vehicle. Based on test results automatically collected from the brake test, the program produces a printout with PASS/FAIL evaluation of the brake performance of the vehicle. Advantages

● Make you test printout comparable to the VOSA GVTS printout. Automatically brake test data collection when used with BM brake testers model BM12200, BM17200 and

http://bmtest.dk/Default.aspx?ID=19 (2 of 4) [25/10/2012 10:27:09 a.m.]

BM Windows software and PDA system

BM12200 ● With manual entry of brake test result,

the program can be used with any brand of brake tester.

Benefits

● Saves costs by reducing number of FAILS and re-check to the VI station.

● Improves your PASS rate and hereby enhance your customer service.

● Motivates your staff with state of art inspection equipment.

The BM VOSA Database Manager program offers a test guide on PC monitor as well as a digital guide on the main display. This guide system maintain the one-man operation concept of BM brake testers. The BM VOSA Database Manager program is used by many DP customer in England and by the VOSA organisation.

Click to view

3. Sicherheits Prüfung program BM Sicherheits-Prüfungs-Programm „SP Windows“ Windows 98/NT/2000/XP basiertes Programm, InterBase SQL-Datenbank. Erfassung der Fahrzeug-Mängel, Brems-Prüfergebnisse im SP-Protokoll und automatische Hochrechnung der Gesamtabbremsung zur ordnungsgemäßen Beurteilung der Fahrzeugbremsen. Vorteile: Automatische Bremsprüf-Datenerfassung bei BM-Bremsprüfständen Modell BM12200 bis BM20200. Manuelle Eingabe der Bremsprüf-Ergebnisse bei beliebigem Bremsprüfstand. Einfache Abarbeitung der SP, Ausgabe von SP-Protokollen. Automatische Statistiken und Prüfplakettenverwaltung. Prüfanleitung auf PC-Bildschirm, alle Messwertanzeigen des Prüfstandes auch auf Monitor. Prüfstandssteuerung über PC (bzw. Laptop oder PDA) möglich. BM PC-Software seit Jahren auch bei Großkunden wie Fahrzeugherstellern im Einsatz. BM VOSA Database Manager in vielen Prüf-Werkstätten in England und der VOSA Organisation.

http://bmtest.dk/Default.aspx?ID=19 (3 of 4) [25/10/2012 10:27:09 a.m.]

BM Windows software and PDA system

4. RTS Mobile program

The RTS mobile program is a Windows 2000/XP based program and designed to perform data collection when the vehicle is driving on the road. The RTS mobile program automatically collects measured air pressure values using the BM radio air pressure sensors. The data enables you to perform analysis of how the air pressure system of the vehicle is performing in "real life". This is particular interesting when performing diagnosis on a vehicle, which has a dynamic adjustment of the air pressure system based on data measured during driving.

<< back Top

BM Autoteknik A/S | Erhvervsparken 7 | 9632 Møldrup | Denmark | Phone: +45 8669 2022 | Fax: +45 8669 2199 | Email: Write

http://bmtest.dk/Default.aspx?ID=19 (4 of 4) [25/10/2012 10:27:09 a.m.]