of 4
8/17/2019 BocaPCM Catalogue 2010 B
1/4
寶加國際有限公司寶加國際有限公司
BOCA INTERNATIONAL LIMITEDBOCA INTERNATIONAL LIMITED
寶加寶加相相變變熱蓄熱蓄能能系系統統Boca Phase Change Material Thermal Energy Storage SystemsBoca Phase Change Material Thermal Energy Storage Systems
Reduce >50% Global Warming EffectReduce >50% Global Warming Effectdue to Air Conditioning Systemsdue to Air Conditioning Systems
BocaBocaPCMPCMTMTM
8/17/2019 BocaPCM Catalogue 2010 B
2/4
NATURAL ALTERNATIVE TO REDUCE ENERGYNATURAL ALTERNATIVE TO REDUCE ENERGY
INTRODUCTION;INTRODUCTION;
HOW DOES IT WORK ?HOW DOES IT WORK ?Thermal Energy Storage (TES) reduces the size of
heating and cooling machinery by means ofspreading the day / peak time load over either
night / off-peak times as in the case of Full Storage
TES systems, or alternatively over a 24 hour period
in the case of Partial Storage TES systems. Hence,any type of TES system can not only be
considered as a useful tool to reduce the overall
environmental impact for a given cooling / heating
application but also it offers significant operational
cost savings.
BocaPCM-TES-Panel containers can be filled with any of the following PCM solutions to satisfy many HVAC and Refrigeration
applications. All the current BocaPCM solutions are non-toxic and natural substances and therefore BocaPCM-TES systems offeran environmentally friendly solution for modern day cooling and heating applications.
Stress & StrengthStress & Strength
Tests;Tests;
PressurePressure
MechanicalMechanical
strengthstrength
Life cycleLife cycle
Point impactPoint impact DropDrop
LoadingLoading
CorrosionCorrosion
High ImpactHigh Impact
Thermal Tests;Thermal Tests;
FreezingFreezing
MeltingMelting
Super coolingSuper cooling
SuperheatingSuperheating
ThermalThermal
propertiesproperties
LongLong--termterm
stabilitystability
Thermal Energy Storage
(TES) is the temporary
storage of high or low
temperature energy for later
use. It bridges the gap
between energy requirement
and energy use.
A thermal storage application
may involve a 24 hour oralternatively a weekly or
seasonal storage cycle
depending on the system
design requirements. Whilst
the output is always thermal,
the input energy may be either
thermal or electrical.
BocaPCM-TES-Panel conceptis based on custom-made
HDPE plastic containers filled
with our Phase Change
Materials (PCM) solutions
which have very wideoperating temperatures
between +8+8ºC(+46C(+46ºF)F) & +117+117
ºC(+273C(+273 ºF)F).
BocaPCM-TES-Panel custom-made HDPE
plastic containers are filled with BocaPCM
solutions and the filling screwed cap fully UltraSonic Welded after filling in order to ensure safe
and reliable operation.
The design of plastic container incorporates
internal support columns as well as externalguide circles so that the containers can be
stacked on top of each other forming a self-
assembling large heat exchanger within the tank.
The self-stacking concept can be applied for
both water and air circuits and the gap between
each container provides an ideal flow passage
with a large heat exchange surface.
FEATURES;FEATURES;
8/17/2019 BocaPCM Catalogue 2010 B
3/4
INNOVATION FOR ENERGY SAVING TECHNOLOGIESINNOVATION FOR ENERGY SAVING TECHNOLOGIES
BENEFITSBENEFITS
TANK DESIGN;TANK DESIGN;Generally concrete tanks are either built buried below
ground level and the top of the tank used as parking or
andscape areas or alternatively within the basement
area as part of the foundations. Tanks ideally should
be constructed as close as possible to chillers and load
o minimise the pipe work and pumping energy
penalties. If the system requires pressurised tank acylindrical tank can be constructed to accommodate
BocaPCM-TES Panels with minimum by-pass.
BocaPCM-TES Panels can only be stacked up to aheight of 2.6 m (8 ½ ft) level and therefore the height
of the tank is restricted to around 3m (10 ft) and the
oot print of the tank can be adjusted around this limit.
n principal.
Furthermore, if the required storage capacity is too large and the design requires multiple tanks, they can be arranged either in
parallel or series format to suit the application and available space. Typically the depth of the tank will be 2.6 m (81/2 ft) inside
dimension which corresponds to approx. 52 BocaPCM-TES Panels high and 150mm (6”) of head room above the containers.
Therefore, to estimate the approximate rectangular tank size and shape one can use the following formula inline with BocaPCM-
TES-Panel capacity table.
FLEXIBLE SYSTEMFLEXIBLE SYSTEM
The overall machinery capacity and TES capacity can beexactly matched to system loads.
INCREASED CAPACITYINCREASED CAPACITY
As a retrofit application, the additional TES load may increase
the system output without any additional machinery.
QUICK RESPONSEQUICK RESPONSE
BocaPCM-TES panels offer quicker response in comparison
with any other TES systems on the market.
REDUCED MACHINERYREDUCED MACHINERY
Shifting some of the peak load may enable designers to
reduce the main machine size.
GREEN SOLUTIONGREEN SOLUTION
Reduced machinery size, energy consumption results in both
direct and indirect CO2 emission.
LOWER MAINTENANCE COSTLOWER MAINTENANCE COST
Machinery runs for longer periods without any start / stop
and therefore it offers a far more reliable operation.
REDUCED RUNNING COSTREDUCED RUNNING COST
Load shifting provides reliable operation and lower annual
electricity / energy running costs.
STANDSTAND--BY CAPACITYBY CAPACITY
In case the main machinery fails, the stored energy can be
utilised to handle the system loads, hence, providing a
degree of back up facility.
SI Units;
Load (kWh)Load (kWh)
----------------------------------------------------------------------------------------- = Length (m) x Width (m)= Length (m) x Width (m)
ocaPCM Capacit yocaPCM Capacit y (kWh/m3) x 2.6(kWh/m3) x 2.6
IP Units;
Load (TRh)Load (TRh)
-------------------------------------------------------------------------------------------------- = Length (ft) x= Length (ft) x Width(ftWidth(ft))
BocaPCM Capacit yBocaPCM Capacit y (TRh/m3) x 8.528(TRh/m3) x 8.528
WATER SYSTEMWATER SYSTEM AIR SYSTEM AIR SYSTEM
8/17/2019 BocaPCM Catalogue 2010 B
4/4
寶加國際有限公司寶加國際有限公司 BOCA INTERNATIONAL LIMITEDBOCA INTERNATIONAL LIMITED456, Shui Lau Tin, Pat Heung, Yuen Long, N.T., Hong Kong.
香港新界元朗八鄉水流田456號Tel: +852-31766028 Fax:+852-31766099 e-mail : [email protected]
WORLD LEADER IN ENERGY SAVING TECHNOLOGIESWORLD LEADER IN ENERGY SAVING TECHNOLOGIES
TECHNICAL SUPPORT:TECHNICAL SUPPORT:
Boca International Limited has been setup since 1992 in Hong Kong and is now spending full effort in
Environmental Energy Saving Solutions research & development by means of Inorganic Phase Change Materialand offers full system design support to assist in proper selection and integration into existing or new installations as
part of our customer commitment.
FREE IMPORT TAX TO CHINA (CEPA):FREE IMPORT TAX TO CHINA (CEPA):Our factory in Hong Kong has been approved by Hong Kong & China Government as one of the CEPAmanufacturer in Hong Kong, as a result, there will be no import tax for our products to be delivered to China.
JOB REFERENCE;JOB REFERENCE;