Name of work : Mughal Museum, Eastern Gate, Tajganj Agra
Bill o f guanit~
SI. No. Description of Work Unit Qty.
A EARTH WORKS Earth work 1n surface c~cavat,on not e~ceeding 30 cm in depth but
1 exceed ng 1. S m ,n width as well as 10 sqm on plan including d soosal of
exc,wated earth upto 50 m ,ind lift upto 1.5 m, disposed soil to be
levelled and neatlv dressed ·
I All kinds of soil lOOsqm 178.98
Excavauon In foundations 1n Ordinary Soil (Loam Clay or sand) including
ltft upto l.Sm. and lead upto 30 m. & Including filling, watenng and
ramming of excavated Earth in to the trenches or in to the Space between
2 the building and sides of foundation trenches or in to plinth and removal Cum 80829.97
and d1soosal of surplus earth as directed by the engineer·1nchargos upto
a distance of 30m. from the foundation trenches.
Add to Item 251-253 for every add111onal 30 m. (lOOft) lead or part of 30 m.
3 ( JOOfts) or for every add1t1onal 1 5 m. (Sit~) h11 or part of 1 Sm. (Sfts)
I l Sm to 3m Cum 16253 82
II l Sm to4 Sm Cum 31764 60
iii 1 Sm to 6m Cum 117646,90
IV 1 Sm to 7.Sm Cum 63529 20
v l Sm to 9m Cum 70305 75
vi l Sm to 10.SSm Cum 9078.96
F1ll1ng available excava ted earth (excluding rock) in trenches, plinth, sides
4 of foundation~ etc in layers not exceeding 20cm in depth, consolida1 ,ng
each deposited layer by ramming and watering, lead up to 50 m and ,ft Cum 5790.71
UPtO 1 5 m. Carriage of ballast, kankar coal, grit or sand including loading and
s unloading but excluding stacking on pucca roads: Skm Cum 75039.26
Sand fllhne 1n plinth including Supply of nl!cessary quantity of sand from a
distance not exceeding 8 km (5 miles) from the site of work and including
6 watering, ramm1ng,dre~)mg e1c. rate 10 include cos1 of all matt!rial~. labour Jnd um 1279 78
T & P etc required for proper completion of the work (Lead upto lOm & lilt
1 SmJ An11term,te treatment of along external wall where the apron is not prov1d1ng
7 using chemical rmuls1on @7 511trcshqm ol vertical surface of the substructure to a d~pth ol 300mm including excavation channel along the wall & rodding et, complt•tc Wilh Chlorpyriphos/L,ndane EC 20% with l Ill concen tration
Sqm 193 05 I
Ant1term1te treatment or Soil under floors using chemical emulsion @ one litre
8 pl'r hole 300n"m apart @JOO Nos Holes per 9 00 Sqm including drlllmg l 2mm diameter holes and plugging also to match the floor properly:
i With Chlorpyrtphos/Llndane E.C. 20% with 1% concentration
Sqm 10543 50
9 Construct on of granular sub-base by prov1d1ng close graded Mater al
conform,l"g to spec,r cations. mixing in a mechanical mix p tant at OMC,
carriage of mixed material by tippers to work s te, for all 'cads & lifts,
spreading in uniform layers of speci fied thickness with motor grader on
prepared surface and compacting with vibratory power roller to achieve
the desired density, complete as per specifications and directions of
Fng1neer ·ll)·Ch.irge
I With matena conform,ng to Grade-I ts1zc range 75 mm to 0.075 mm) tdm 581. 72
having CBR Value-30
~~· wq~ \lo s:r. xl. f;!i. frl. ~1
..
~~-1. 31T1Ri
~ vft~ lfr. f~4~ ~- ~~Qofl'T ~. "O. ~ . ~ r... fc;J. ~ ~ .. \1. ,~. ~- ,·
~fail\!~ 1, \IFh 3JT7m ~ 3IT7m
Rate in Rs.
4791
99.00
9 00 9.00
9.00
9.00
9.00
9.00
99 00
151.00
7~0 00
118 00
142 00
2013 00
I SI. No. Description of Work
ii With material conforming to Grade-II (size range 53 mm to 0.075 mm )
having CBR Va lue-25
~ - uONCRETE WORKS Providing and laying in position cement concrete of specified grade
excluding the cost of centering and shutteringProviding and laying in
position ready mixed pla in cement concrete, with cement content as per
approved design mix and manufactured in fully automatic batching plant
and transported to site of work in transit mixer for all leads, having
continuous agitated mixer, manufactured as per mix design of specified
1 grade for pla in cement concrete work, including pumping of R.M.C. from
t ransit mixer to site of laying and curing, excluding the cost of entering, shuttering and finish ing, including cost of curing.admixtures in
ommended proportions as per IS : 9103 to accelerate/ retard setting of
concrete, improve workability without impairing strength and durability
as per direction of the Engineer-in-charge. - All work up to plinth level :
i M-10 grade plain cement concrete (cement content considere
@ 220 kg/cum) M-7.5 grade plain cement concrete (cement content considere @ 200
ii kg/cum)
REINFORCED CEMENT CONCRETE WORK
2 Centering and shuttering including strutt ing, propping etc. and removal
of form for:
a Foundations, footings, bases of co lumns, etc. for mass concrete.
Walls (any thickness) including attached pilasters, butteresses, plinth and
b string courses etc.
c Suspended floors, roofs, landings, balconies and access platform.
I Edges of slabs and breaks in floors and walls Under 20 cm wide
Extra for additional height in centering, shuttering where ever required
with adequate bracing, propping etc. , including cost of de-shuttering and 3 decentering at all levels, over a height of 3.5 m, for every additional
height of 1 metre or part thereof (Plan area to be measured).
i Suspended floors, roofs, land ing, beams and balconies (Plan area to be
measured) Steel re inforcement for R.C.C. work including stra ightening, cutting,
4 bending, placing in position and bf'nding all complete upto plinth level
And above plinth level
i Thermo-Mechanica lly Treated bars
Provid ing and laying in position machine batched and machine mixed
design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including
pumping of concrete to site of laying but excluding the cost of centering, 5 shuttering, finishing and reinforcement, including admixtures in
recommended proportions as per IS: 9103 to accelerate, retard setting
of concrete, improve workab ility w it hout impairing strength and
durability as per direction of Engineer-in-charge.
(Note :- Cement content cons idered in this item is @ 330 kg/Cum.
Excess/less cement used as per design mix is payable/recoverable separately).
4 Btf~(m.)
t£_J . ~ ffio)
~o Uo xf. r'lo r'lo f, 31JTRT ~c/5"1~ - 1, ;.~1T11~~
.Jo '!.'.fu \"fo F1o ~1o G> 3lP~ ~cpft - 1, ·~IFJ~l
Unit Qty. Rate in Rs.
cum 1163.44 2018.00
cum 910.00 5551.00
cum 378.00 5406.00
SQM 673.74 186.00
SQM 1170.40 342.00
SQM 18082.00 381.00
Rmt 2447.50 110.00
SQM 18082.00 151.00 '
Qtl 24216.00 5334.00
SI. No. Description of Work Unit Qty. Rate in Rs.
i All works upto plinth level.
Cum 3001.00 5981.00
Al l works above plinth level upto floor V level. ii Cum 1123.00 6663.00
Extra for providing richer mixes at all floor levels. Note:- Excess/less 6 cement over the specified cement content used is payable /recoverable
separately.
i Providing M-35 grade concrete instead of M-25 grade BMC /RMC. (Note
Cum 4158.00 145.00 : Cement content considered in M-35 is@ 350 kg/cum) Providing, hoisting and fixing up to floor five level precast self compacting reinforced cement concrete in lintels, beams, wall and
7 bressumers, including setting in cement mortar 1:3 (1 cement : 3 coarse cum 10378.00 13219.00
sand), cost of requ ired centering and shuttering but excluding t he cost of reinforcement with M-35 e:rade concrete Providing and fixing 50 mm thick shalitex board for expansion joints
9 between column, beam, slab and walls etc. as per manufacturers Sqm 45.89 142.00 soecification and recommendation.
10 Providing and fixing sheet covering over screws as per design.
expansion joint s with iron
a Aluminium fluted strips 3.15 mm t hick. 200 mm w ide
i metre 199.50 437.00
C, BRICK WORKS ., First Class · 150 brick work in 1:6 cement and Coarse sand of 1.25 fineness
1 modulus mortar in foundation and plinth including supply of all materials, labour and tools and plants etc.required for proper completion of the work.
As in item (303) above, but in 1:4 cement and Coarse sand mortar.
i Cum 50.00 4180.00
As in item (303) to (307) above but in super structure above including
2 necessary cutting and moulding of brick work as required and also including
Cum 50.00 342.00 honey combed brick in thickness of wall not to be less than 1. 1/2 brick thick. Add For Extra labour to above items.
3 As in item 2 & 3 above but in superstracture for wall thickness 12cm and below
Sqm. 25.00 484.00 add extra.
4 As in item 2 & 3 above but in superstracture for wa ll thickness 8cm and below
Sqm. 25.00 475.00 add extra.
5 Extra for providing and placing in position 2 Nos. 6mm dia. M.S. bars at
Sqm. 25.00 66.00 every third course of half brick masonry (with F.P.S. br icks).
D MARBLE & GRANITE WORK 1• •
Providing and fixing 18mm thick gang saw cut ( premoulded and
prepolished) machine cut for kitchen platforms, vanity counters, window
sills , facias and similar locations of required size of approved shade,
1 co lour and texture laid over 20mm thick base cement mortar 1:4 (1
cement : 4 coarse sand) with joints treated with white cement, mixed
w ith matching pigment, epoxy touch ups, includ ing rubbing, curing,
moulding and polishing to edge to give high gloss finish etc. complete at all levr->I~. Granite of any colour and shade.
i Area of slab over 0.50 Sqm.( For Counter) Sqm. 26.28 3712.00
P/L 18mm Black Granite Stone (super quality) Flooring over 25mm th ick base of
2 cement mortar 1:4 (lcement:4 coarse sand) laid and jointed with white cement Sqm. 563.92 3325.00 slurry including rubbing and polishing complete.
SI. No. Description of Work
Item same above (8.2.2.2) Granite Stone (polished) work for wall lining
3 over 12mm thick bed of cement morta r 1:3 (1 cement : 3 coarse sand)
and cement slurry@ 3.3 kg/Sqm. including pointing in white cement
comolete. Extra for fixing marble/ granite stone over and above corresponding
4 basic item, in facia and drops of w idth upto 150mm with epoxy resin
baesd adhesive includ in_g cleanin_g etc. complete. Extra for providing opening of required size & shape for wash basins/
kitchen sink in kitchen platform, vanity counters and similar location in
5 marble/Granite/Stone work including necessary holes for pillar taps etc.
including rubbing and polishing of cut edge etc. complete.
E WOOD & PVC WORK I '
Provid ing and fixing IS : 3564 marked Aluminium die cast body tubular 1 type universal hydraulic door closer wit h necessary accessories and
screws etc. comolete. Providing and fixing aluminium tower bolts ISi marked anodised (anodic
2 coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed
to required colou r or shade w ith necessary screws etc. complete :
i 300x10 mm
ii 100x10 mm
Providing and fixing aluminium pull bolt lock, ISi marked, anodised
3 (anodic coat ing not less than grade AC 10 as per IS: 1868) transparent or
dyed of required colour and shade, with necessary screws bolts, nut and
washers etc. complete. Providing and fixing aluminium handles of approved make anodized
4 (anodic coating not less than grade AC 10 as per IS: 1868) transparent or
dyed to requ ired colour or shade with necessry screws etc. complete.
i 125 mm
ii 100 mm
Providing and fixing aluminium hanging floor door stopper ISi marked
5 anodised (anodic coating not less than grade AC 10 as per IS : 1868)
t ransparent or dyed to required colour and shade w ith necessary screws
etccomolete.
i Single rubber stopper
Providing and fixing bright finished brass 100 mm mortice latch and lock,
6 151 ma rked, with six levers and a pair of anodised (anodic coating not less
than grade AC 10 as per IS : 1868) aluminium lever handles of approved
aua litv with necessarv screws etc. complet e
E MILD STEEL AND IRON WORK .,
1 Alloy steel Anchor bolt plates, dashfasteners, angles, channels, shelves
and fabrication for Fixing Colum n Mild steel or iron work in heavy sizes such as trusses; builts up gates, door frames.record racks, roof work, gates etc. wrought to required form including
2 drill ing holes,rivetting or welding where necessary and also including supply of steel, bolts, nuts etc. & thei r fixing required for proper completion of the work.
4/i-\{tf ~ (ft-1~)
'iio >lo xfo ~• f.lo f'i~Tn
~~-1, 3!Pm
Unit
Sqm.
rmt
each
each
each
each
each
each
each
each
each
kg
kg
Qty. Rate in Rs.
763.67 3712.00
43.80 235.00
32.00 367.00
42.00 716.00
84.00 106.00
10.00 49.00
18.00 72.00
84.00 66.00
10.00 52.00
24.00 35.00
17.00 774.00
184000.00 247.00
200.00 55.00
~ ~cpr~ !l'irSr
.1 a a. ~. f.'i. ~. f u«rm~-1.~h.
SI. No. Description of Work I
Unit Qty.
Providing and fixing stain less steel ( Grade 304) railing made of Hollow tubes, channels, plates etc, including welding, grinding buffing, polishing and makine curvature (wherever required) and fitting the same with necessary stalnless steel nuts and bolts complete, 1/c fixing the railing wi th necessary accessories & stainless steel dash fasteners
3 stainless steel bolts etc, of required size, on the top of the floor or the Kg. 2224.20
side of wast slab with suitab1e arrangement as per approval of Engineer in-charge (for payment purpose only weight of stain less steel members shall be considered excludi11a fixing accessories such as nu ts, bolts fasteners etc ).
~ FLOORING & DADO WORK Providing ang laying 18mm Agaria White marble stone (super quality) flooring ovC!r 25mm thick base of cement monor 1 a (1 cement 4
272 24 1 coarse sand) laid and joined w1tl\ white cement slurry including rubbing
Sqm.
dnd oohh1n11 comolete. Prov1din3 ang laying 2Smm Kota stone slab flooring over 20 mm th1ck j base or cement mortar l : 4 (1 cement 4 coarse sand) laid over and
2 Jointed with grey cement slurry mixed with pigment to match the shade Sqm. 4794.22
of the slab 1nclud1ng rubbing and pohshine complete
Kota stone slab 20 mm thick 1n risers of steps, sk1rt1ng. dado and pillars laid on JO mm thick cement mortar 1:3 (1 cement 3 coarse sand) and
3 101nted with grey cement slurry mixed with pigment to match the shade Sqm. 131 58 of the slabs, Including rubbing and polishing complete.
Providing and laying 70 mm thick Agra Red Stone flooring over 20 mm
(average) thick base of cement mortar l :5 (1 cement ·S coarse sand ) 4 with 10 nts 3 mm thick, s,de buttered with cement mortar 1 2 (1 cement Sqm 6234 59
2 stonl! dust) adm,xed with PtRment to match th<> shade of s1011e ilnd oointme with same mortar. Marble stone flooring w•th 30mm th,ck marble stone, as per sample of marb,e approved by Ena,neer-in-charge, over 20 mm (average) thick
5 ba~e of white cemQnl mortar 1 4 (1 cement · ii coarse sand) laid and Sqm 19937 68 JOtnted w,th while cement slurry, ,ncluding rubbing and ool,shing
complete with Providing and lay,ng Grani te Cobb1e Stone 150mm x 150mm x 75mm
thick w th Anti skit Leather F1n1sh over 20 mm (averaee) thick base or
6 cement mortar 1:5 (1 cement :5 coarse sand) with joints 3 mm thick, side
Sqm 1898.77 buttered with cement mortar l 2 (1 cement 2 stone dust) admixed with pigment lo match the shade of stone and pointing with same mortar.
Provid ng & laying 75 mm thick vacuum dewatered flooring (trem1x floor) of RMC or grade M-25 including providing & milking 8mm wide .ind
20mm deep groove at 4mtr. x 6mtr maximum panels or as directed and filling tne groove with seillant (colpor 200 of fosroc chemkal or
7 approved ma<e). side shuttering with MS channels, v1braung concrete by Sqm 139.09
us,ng screed vibrator and suction dewaumng using ilpproved make equipment and r,mshing the top surface to required level and grade
using power trowels of standard make excluding nominal steel remforcement Drv CladdinR Prov,d,ng c1nd f.iong dry cladding white Marble stone upto 10 metre
heights with 30 mm thick e.ing saw cut stone with (machine cut edges) or uniform colour and size upto lmxlm, fixed to structural steel frame
8 work and/ or with the help of cramps, pins etc. and sealing the join ts Sqm 4663.04
with approved weather sealant as per Architectural drawings. Cost of
The steel frame work, starnless steel cramps and pins etc ,s t'Xtra
qq~ ~ ., ~o Jin 'fl , ~ 1 ,
~~ ~i;l. ~,. -31~4.:til \J. u. ~. r... ~. rc... 3'T1ro ~. anrm
~o ~o ~ • ~ o f"I I
~~-1 ~fl~j = ='""· . 1Q11·1"1 S n r;, - ,, ,·id
Rate In Rs.
570.00
2565.00
1068.00
593 .00
3121 00
4]75 00
7824 00
522.00
2660.00
SI. No. Description of Work
Providing and fixing structural steel frame (for dry cladding with 30 mm
thick gang saw cut with machine cut edges sand stone) on walls at al l
heights using M.S. square/ rectangular tube in the required pattern as
per architectural drawing, including cost of cutting, bending, we lding etc.
The frame work shall be fixed to the wal l with t he help of M.S. brackets/
lugs of angle iron/ flats etc. which shall be welded to the frame and
embedded in brick wall w ith cement concrete block 1:2:4 (1 cement :2
coa rse sand :4 graded stone aggregate 20 mm nominal size) of size 9 300x230x300 mm, including cost of necessary centring and shuttering
and with approved expansion hold fasteners on CC/RCC surface,
including drilling necessary holes. Approved cramps/ pins etc. sha ll be
welded to the frame work to support stone cladding, the steel work wi ll
be given a priming coat of Zinc primer as approved by Engineerin-charge
and painted w ith two or more coats of epoxy paint (Shop drawings sha ll
be submitted by the contractor to the Engineer-in-charge for approval before execution).
The frame work shall be fixed in true horizontal & vertical lines/planes.
(Only structural steel frame work shall be measured for the purpose of payment, stainless
steel cramps shall be paid for separately and nothing extra shall be paid).
Providing and fixing adjustable sta inless steel cramps of approved
quality, required shape and size, adjustable w ith stainless steel nuts,
10 bolts and washer (total weight not less than 260 gms), for dry stone
cladding fixed on frame work at suitable location, including making
necessary recesses in stone slab, drilling required holes etc complete as oer direction of the EnP:ineer-in-charn-e. Supplying and placing of Wh ite Marble Agaria stone column
11 250x350x9000mm in given position in five parts joint w ith four stainless
pins of 300mm length and linch dia. and two steel plates bolted on the rear side.
H ROOF & FALSE CEILING WORK I
Providi ng gola 75x75 mm in cement concrete 1:2:4 (1 cement: 2 coarse
1 sand : 4 stone aggregate lOmrn and down gauge) including finishing with
cement mortar 1:3 (1 cement : 3 fine sand) as per standard design.
i In 75x75mm deep chase. Making khurras 45x45 cm with average minimum thickness of 5 cm
cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone
2 aggregate of 20 mm nominal size) over P.V.C. sheet lmxlmx400micron,
finished w ith 12mm cement plaster 1:3 (1 cement : 3 coarse sand) and a
coa t of neat cement, rounding the edges and making and finishing the outlet comolete.
ffe-~~~o)
~ 1.if .. ~ •. ~ ,, A , f' ·w ~~:-~~:,srr . ' ')ffi ;\
Unit Qty. Rate in Rs.
,,
kg 11658.00 132.00
each 18652.00 195.00
-
each 640.00 66500.00
Rmt. 1215.45 135.00
each 101.00 156.00
SI. No. Description of Work Unit Qty.
Providing and fixing 12.Smm thick tapered ed6e gypsum plain board confonng to IS· 2095-pan-l false ceiling at all height including providing
and fixing of frame wor~ made or special sections power pressed from
M S sheet and galvanised 1n accordance wnh zinc coating of 120
gms/sqm (both side inclusive) as per IS 277 and consistins of anfile
cleats of size 2Smm wide x l .6mm thick with flanges of 27mm and
37mm at 1200mm centre to centre one flange fixed to the ceillnB with
dash fastner 12 Smm d1ax40mm long with 6mm dia bolts to the angle
3 hangers of 25x10x0 SOmm of required length with nuts & bolls of
requi red size and other end of angle hanger being fixed with
intermediate G .I channels 4Sxl 5x0.9mm running at the spacing of
1200mm centre to centre 10 which the ceiltng section O 5mm th,ck
botton wedge of 80mm with tapered flanges of 26mm each having clips
'
of 10.Smm at 450mm centre to centre st,all be fixed In a direction
perpend·cular to G I intermediate channel w1lh connecung clips made
out of 2 64mm d.ax230mm long G I wire at every Junction including I fixing perimeter channe:s OSmm thick 27mm high having flances of ")n-- --....1 ,I'\ __ 1-. ... - ·h.-. -- ·-- """ n.f ,,...,IJ,.,,n f -.M ,... 1"'1 ll/r1,- .. 6.,t --
of rawi plugs at 450mm centre to centre w·th 25mm long dry wall screws
@ 230mm interva1 including 101nttng and fixing of gypsum board to
ceiling section and perimeter channel with the help of dry wall screws of
size 3 5 X 25 mm at 230 mm c/c. including Jointing and fin1sh1ng to a
flush f1msh of tapered and square edges of the ooard with
recommended J1ont1ng compound, Jointing tapes. f1nlshtng with jolnung
compound in 3 layers covering upto 150 mm on both sides of Joint and Sqm 550.00
two coats of primer suitable for board. all as per manufacturer's
specification and also 1nclud1ng the cost of ma~1ng opening for light
fitting, oritls, diffusers, cutouts made with frame of perimeter channels
suitably fixed, all compiete as per drawing. spec,f1cat1on and direction of
the eng,nner 1n charge t>ut the cost of pa1n11ng with I
I
I FINISHING WORK
Fin sh111g w,th C.poxy painl (two or more coats) at all locations prepared
l and appl ed as per manufacturer's specif cations including aopropr·ate
priming coa t , prcparat on of surface, etc complete
I On steel work sqm 10.00 Finishing walls with acrylic emulsion paint of approved brand and
manufacture and of required shade and undacorated wall surface to give
z even shade over lnciudtng curing and cost of all material, labor, Sqm 550.00
T&Pat1ent etc required for proper compleuon of work for two coat
Providing and applying while cement based putty of average thickness 1
3 mm, of approved brand and manufacturer, over the plastered wall
Sqm 550.00 surface to prepare the surface even and smooth complete
J DISMANTLING WORK
Demolishing brick work or stone work in lime or cement mortar and
1 1nclud,no stacking of matena,s as directed by Engineer-m-chargc with m cum 3,475 00
a distance of 60 meters (200 feet) D1smol1sh1ng rein forced cement concrete or reinforced brick work
2 ,nclud,ng stacking of dismantled materials as directed engineer· 1n· cum 2,110.00
charge w•tt, In ..i distance of 60 meters (200 feet) 3 Dismantling doors and windows includmg stacking of materials as
directed by Engineer in-charge with in a distance of 60 meters (200 sqm 50.00
feet).
4 01smantallng tile work 1n floor and roof lc1id In cement mortar 1nclud1ng
stacktni: material within 50 metre lead
(; ii 1V..
. A:£-- (~ ~ , . ,( I 1-Tj
\ . ~ ~fh ( • ., 0 f-7,qcfi ~ I
r ~ I · l. ...., . ' ·~ Wa 'Ao ~ . Pr. ~ 1, 5PNf ~ - 1. 31(/f~J
~ (. , ... ~. ~~ .' P. 11 . f." ~. 'T
TI7 :, ,;r: . ,fl T<
(j) Rate in Rs.
665.00
110.00
57 00
85 00
427.00
769.00
57 00
~ ~ '1.. IL ~. ~. ~ . ~. ~~-1. 3fllfil
SI. No. Descrlptior1 of Work Unit Qty.
I For thickness or Iles lOmm 10 25mm sqm 1170.00
D1smanlling ston~ slab flooring laid In cement mor tar including stackin
5 of serviceable materi.i and disposal of unserviceable material w ithin 5 sqm 2730.00
metre lead :
6 Dismantling exist ng plaster includ ,ng disposal of refuse as directed b·
EnP. ,neer· n-char2e w,th in a d•stance or 60 meters. sqm 50 00
01sposar of building rubbish I ma lba / sim ilar unserviceable, dismantlec
or waste materials by mechanica l means includ,ng loading, transporting
7 unloading to approved municipal dumping ground or as approved b1 cum 2.500 00
Engineer-in-charge, beyond 50 m initial lead, for all loads includ ng a
lifts Involved.
K ALUMINIUM WORK Prov•ding and fixing atum1n1um worl< for doors, windows, vent ilators anc
parttuons w ith extruded built up standard tubular sections/appropriate Z sections Jnd other sections of approved make conforming 10 IS. 733 anc
IS 1285, fixed with dash fasteners of requ,red dia and size includin1,
necessary fil ling up of gaps at Junctions, at top, bottom 11nd sides with
1 required EPOM rubber/ neoprene gasket etc Aluminium sections shal
be smooth, rust free, s1rn1ght, mitred and Jointed echan1cally wherever requ red 1nclud1ng de.it angle, Alumin,um snap beading for glaz ,ng /
pane ,ng. CP or ass / sta n ess stee screws, all complete as per architectural dr;iw,ngs and the direct ions of Engineer ,n-charge. Glazlnr and paneling 10 be paid for separately)
Anod sed atumin,um (anodised transparent or dyed to requ ired l
I shade according to IS. 1868, M inimum nnodic coa tine of grade KG 332 34
AC 15) For shutters of doors, windows & vent ilators including prov,d ng and
2 fixine h1nses/ prvots and making provision for llxinu of fitt ings wherever
required including the cost of EPDM rubber I neoprene gasket requ1red
(F1ttin11.s shall be oa td for seoaratelv) Anod ised aluminium (anodised transparent or dyed to required
i sh.:ide according 10 IS. 1868, M inimum anodic coatong of grndc KG 488.94
AC 15) Prov,d,ng and I ).1ng gazing in alurnin,um door, window, ven111a1or
shutters and part .t ,ons etc. w,th EPOM rubber I neoprene gasket etc
3 complete .is per the arch,tectura drawings and the dlfect,ons of
engineer-in-charge . (Cost of aluminium snap beading shall be paid tn
oasic item) I With 8 mm thickness Tou~hened Glass Sam 87 00
Providing and fixing 12 mm th,ck prelaminated part ,c c bonrd flat
pressed three layer or graded wood part •cle ooard conforming to IS:
4 1?823 Gt.:ide Type II, n p,, nC'lhne f1XL'd in alum,nurn doors. w111dow~
shutters ,1nd part uon frames w,th C P b'ass I sta,nless steel sc,ews etc.
complete c1s per archltt>ctural drnwinns and dlrewons of cng,ncer- ,n·
charRe.
I Pre-laminated par11cle board with decorative lam1na1lon on both sides
Sqm 117 12
Filllng the gap 1n between aluminium frame and ad1accn1
5 RCC/Brtckwork/ Stone Work by provid ing weather silicon sealant over
backer rod or approved quality as per arch1tec1uraf dr:iw1ngs and
direction of Engineer-tn-char2e l Upto Smm depth and 5mm width metre 195 70
4 &-r1~
;:tqJ":~)
G~ \ifr;-3. ~·ift
... Q. • 1,::, f ... 1~:1 ..
~ S'~ - I, ·,;,tlWl
~~- ,1,i.. 17-·
~ q, ti. ~ .... t~ ~ i"'Ti.~
® Rate In Rs.
2600
93.00
18 00
117 00
337.00
385 00
1874.00
1035.00
84 .00
SI. No.
6
7
8
Description of Work
Supply and insta'I modular toilet cubicles of MERINO make (Titan SS series) as per manufaturer's std spec1llcat1ons thickness of conipect
laminate 12mm color of HPL boards: single colour size of cub,cle
llOOmm (w) x lSSOmm (d) x 2100mm (h) door size. 190Smm(h) x
610mm (w) overall height of cubicle 2100mm including bottom gap of
130mm Hardware & Fixing: All accessories shall be of Merino's make SS
304 grade includ ng all hardware/fittings. (a) SS 'U' channel (bl SS 'F'
channel for corner units (c) SS too rai l (d) SS coat hook (e) SS pr ivacy
thumb turn c/w occupancy 1nd1cator (f) SS door knob (e) SS hinges with
cover (h) SS adJustable loot-316 erade () rubber hni'"lg for groove (1) SS
screws 304 G & PVC wall plugs
Providing and supplying aluminium extruded tubular and other
alurnin1um secuons as per the architectural drawings and approved shoo
drawings. tne a1umin1um qua 1ty as per grade 6063 TS or T6 as per BS
1474,,nclud ,ng super durable powder coating of 60·80 microns
conform:ng to AAMA 2604 of required colour and shade as approved by the Engineer-In-Charge .
(The item includes cost of material such as cleats, sleeves. screws etc.
necessary for fabrication or extruded alum,n,um frame work. Nothing
extra shall be paid on th is account)
Designing, fabricating, testing, protection. nstalling and f1x1ng in position
sem (gnd) unit1Led system of structural glazing (with open 10,nts) for linear as well as curvilinear ponions of the building for all heights and al l
levels includlnn· (a) Structura l ana;ysis, design and preparation of shop drawings for the
specified design loads conforming to IS 875 part Ill (the system must
passed the proof test at 1 S t imes des,gn wind pressure without any
failure), including funrnon.il design or the oluminum sections for fixing
glazing pane•s of var·ous th icknesses, aluminium c,eats, sleeves and
splice plJtes etc gaskets, screws, toggles, nuts, bolts. ciamps etc,
st•uctural and weather silicone sealants. flasn1ngs, fire srop (barrier) cum
smo'<e seals. m,crowave cured EPDM gaskets for water 11gh1ness.
pressure equa lisat ion & draint1ge and protection against fire nazard
Unit Qty. Rate in Rs.
I
each 66.00 34200.00
kg 14403 39 32100
..
jnrl .. ~ i M • I ~~~-1-~~~~--i~~~~--1
(bl Fabricating and supplying serrated M .S hot dip galvanised !' J\lumin1um alloy of 6005 TS brac~cts of rcqu,red sizes. sections and
profiles etc. to accommodate 3 D1men11onal movement for achieving perfect vcrt1cal1ty and proper fixing of ~tructurol glazing system with the
Ii RCC/ masonry/st ructural steel framework of building structure, using
stainless steel anchor fasteners/ bolts, nylon seperator to prevent
b1metall,c contacts with nuts and washers etc. of stainless steel grade
316, of the required capacity and In rcqu,red numbers
(c) Prov,d1ng and fi lling, two part pump fi l ed. struclural si licone sealant
and one part wea ther silicone sea lant compat ible w ith the structural
silicone sealant of requ ,red bite S1Ze 1n a clean and controlled factory I Iii work shop environment , including double sided spacer tape, selling
blocks and backer rod. all of approved grade, brand and manufacturer,
as per the approved sealant design, w1th,n and all around the perimeter
for ho1d nR n as~. (d) Prov,d1ng and f1x1ng 1n oosition r ashings of solid aluminium sheet 1
mm thick and of sizes, shapes and profiles, dS required <lS per the si te
Iv cond111ons, to seal the gap between the building structure and all its
interfaces w ith curta in glazing to make t watertight
~~ 'io U. xJ. ~. P,. 'IIT'Nf~ - 1. ~ f'l~ l
/~ V.J.~! (ftlo)
:A., u. xi ~ . R1. ~ .. ~ ~ctii'i - I. ,!-fl:o11
~~3 "(;fro .r, -: tr ~- ~. ,~. o, ~. ·~. ,. ri, ~ ij-<>~. JiMI
®
SI. No. Descript ion of Work Unit
(e) Making provision for drainage of mo;sture/ water that enters th,
curtain elazing system to make it wate•ught, by incorporating principle v of pressure equalization, providing sultaole gutter profiles at bot1om (
required). making necessary holes of required sizes and of require,1
numbers etc comolete. This item includes cost o f all inputs of designing, labour for labrrcatin1
and installation of aluminium grid. 1ns-tallation of glazed units, T&P
scaffold ing and other Incidental charges 1nclud ng wastages etc
enabling temporary structures and services, cranes or cradles etc. a
described above and as sp<mf1ed The tern includes the cost of gettint
all the structural and functional design checked and all the sho~ drawings vetted by the Principals or the structural glazing system.
I
The item also includes the cost of all mock ups at site, cost of all sample·
of the Individual components for testing in an approved laboratory, field
tests on the assembled working structura glazing as spec.f1ed. clcaninr;
and protection t il! the handing over of the building for occupat on In the
end. tne Contractor snail provide a water t ght structural glazing havinr,1 Sqm all the performance characteristics etc. all complete as requ red, as pc
the Architectural dr:iw1ngs, as per nem descript ion, as specified, as per " the approved shoo drawings and as directed by the Engineer-,n·Charge
Supply111g 41 52mm thick laminated 1nsu ating toughened gl.iss ( 6mm 9 toughened+ 22mm airgap .. 6mm toughe-.ed + l .52mm Clear PVB .. Sqm
6mm tu(() Supplying 41.52mm th1c~ laminated ,nsu at1ng tougnened glass ( 6mm
10 toughened+ 22mm alrgap • 6mm toughened+ l.52mm MILKY PVB + Sqm
6mm tuffl Supplying and fixing 48mrn thick Imported Double Glazed ceramic
11 Glass.20mm Jade Glass..-6mm tempered clear glass+l6mm cavity+6mm Sqm
Low·E tempered Rlass
L PILE wnRI(
Boring. providing and installa tion bored cast·in-s1tu reinforced cement
concrete piles of garde M 25 of specified diameter and length below pile ca p. to carry a safe work ing 1oad not less than specified, excluding the
cost of steel reinforcement but including the cos t of bor•ng with
oenton,te solution and temporary casing of appropria te length for 1 setting out and remova or same and the length of tile pile to be
embedded n the pile cap etc by Crawier mounted, telescopic boom
hydr..iul1l p,lltng Rig 1111 complete, including romov.il of excavated c-arth
With al 11~ lihs and leads (length of pde ror oayrnent shall be ,icasured
up to bottom of pile cap)
Note: Truck Mounrnd rota ry/TMR/Tube well boring machine shall not
be used. i 600 mm d,a piles 13 metre depth rmt
ii 750 mm dia piles 20 met re depth rmt .
Boring, Providing and Installing cast in situ single under reamed piles of specified diameter and length ~clow pile cap in M-2 5 cement concrete,
to carry a safe working load not less than specified, excluding the cost of 2 steel reinforcemen t bu t 1nclud1ng the cost of boring with bentonite
solution and the length of the p,1e to be embedded in pile cap etc illl
complete (Length of pile for payment shall be measured upto to the
bottom of oi le c;:iol I 300 mm d1a piles S metre depth rmt.
Extra over item No. 20 3 for orov1d1ng add t1on;1I bulb in under reamed
3 piles, under specified d,a meter (Only the quant ity of extra bulbs are to
be oa1d) I 300 mm dia poles ,,,.., ,, - <'ach
~~ / {
.,ft~ ~ v...!'-~ ~~~( .) ' p
iio ~. xlo ~ . p • 'aJINI tcf>r{ - 1. 3!Ph1
i:111~11 ( ,l., '1o Q. ~ r~. f.i. ~ -. ·~ ~¢1~ - 1 ;µrrm
•tir, J. ~ ,1 fl
,1. u ~- .ii. r~,. r~ 11111<1 , ,,f{ >4 H ~
Qty.
8204 98
2010 11
2456.81
3738.06
8983.00 4700.00
3700.00
740.00
Rate In Rs.
2428.00
9785.00
10165.00
25175 .00
344 7 00
4954.00
2016 00
1401 00
~ v ~
\lo Jt. ~ . ~ n ~ • fB<I 3fTTRT ~~ - 1 JlflNI
SI. No. Description of Work
Vertical load testing of piles ,n accordance with IS 2911 (Part IV)
,ncludlng installation of loading platform by Kenttedge method and
preparation of pile head or construcuon of test cap and dismantling of
4 test cap after test etc. complete as per specification & the direction of
Eng,neer in·charge Note. 1 lniual and Routine Load Test shall not be
carried out by Dynamic method of testing. Note 2. Test ing agency shall
submitt the design of loading pla t form for the approval of Eng.neer·in· rh:irno
I lnilial test (Test Load 2.5 limes the Sa fe capacity
It Init ial test (Test Load 2.5 times the Safe capaClty)
Lateral load test1'lg of single pile 1n accordance with IS Code of practice I
s 2911 (Part IV) for determining safe allowable la teral load on pl e
I Upto SO tonne capac,ty pile
II Above 50 tonne and upto 100 tonne capacity p, e
M WATER PROOFING
SUNKEN PORTION(TOILETS)
Surface preparation: Minor cleaning work, removal of loose concrete anc
fill ing cracks with polymer modified mortar using Dr F1x1t P1dicrete URP
Making of angle fillets all around the periphery of the wall with polymer
modif ied mortar using Dr Fixit Pidiproof LW+@ 220ml per bag of
cement Supplying & seal ng the Sanitary pipe inserts, electrical fi t -outs, etc
provided 1n the floor & walls with Bathseal Tape
Supplying & grouttng the gaps around the pipe inserts w ith Bathseal
1 Grout. a non shrink cement1ttous grout The "Nahani" trap, etc 1s to be
fined securely 1n t'le same manner & the gaps around ,t 10 be grouted
with non shrink Grout Supplying 8.. applying 2 coa ts of Dr. F1x1t Bathseal WPC in 1he sunken
areas & extending II up to 150mm above tne finished floor levc This
includes laying of a 150mm wide strip of an ooen woven glass fiber mesh
over thl! .inglc fillets on the 1st coat wh le t 1s still we t
Supplying & l.iymg a protective plaster in lOrnm thickness In Sand
Cement mortar admixed with Dr Fix1t P1dlproof LW+@ 220ml per bag of
cement Terrace waterproofing
Cleanin3 the roof area properly using compressed air
system to ensure that the substrate is free from dust,
la1tanc<.>, debris etc Spray apply an average 30mm thick Dr Fllot Foamsh1e:d ,nsulat1on w,th a
core density of 45-50 kg/m3, U value of 0.513 W/m2.K ,thermal
conduct1v1ty of 0.018 W/m.k at 25 degree mean temperature as per
ASTM C518/91, compressive strength with rise or 11 .2 k5/cm2 as per
ASTM D· 1621/94, fire resistance property confirming to class 82 as per
DINlll07 Provide and apply Dr. F1xn Roof seal, wh,c"i is a single
component cold applied clastomer,c waterproofing co.iung based on
syn thetic resin Emulsion applied wi th a brush/roller In 2 coats to achieve
a OFT of 0.80-lmm{consumot1on {@ 1 I ters/Saml Conduct water ponding/flood tes t after app!1cat1on.
Water shall be filled up Jnd reta ined for at least 24 to
48 hours After emptying the water loosely lay 150 GSM
geotext e(non-woven polvester) 2 A bitumen filler board of l Omm thickness for construcuon 1omts shall be
placed vertically 10 form a rectangular bay not exceed 12m2 10 16m2.
This board will aid to meet the reauired slope.
q . c \ltl .
-... ~ . xTo ~. I· t ·~~-1.~11M
• !Jo -.! I I . r. " 11.·i. ·~~-t. .'"T
Unit
per test
per test
per test
per test
I
f
sqm
I
I
Sqm
::001
@ Qty. Rate In Rs.
1.00 36,633.00
2.00 44,468.00
1.00 16,551.00
2.00 25,378.00
410.34 1121.00
6234 59 3188.00
~~ \Jo tl,- ~o f?J. ~ • fR. ~ ~{ 1 JJlll~I
SI. No.
3
4
Description of Work
All around on the roof, ilt the parapet wa ll Junction, an angular fi lle·
50mm x SOmm shall be trowel applied 1n cement·sand mortar(cemeni.
sand and mortar shall be supplied by you) in 1:3 proport ion
The bituminous f'ller board shall be exposed by means of a mechan1ca1
cutting machine The grooves formed by exposing the filler board sha11
be applied w ith Polysulph1de sealant, Dr F x1t P1dlsea1 42P The w ,dth o·
the sealant fil l shall not be more th.in approx lOmmxlOmm deep
Laying protective slope w ith 75 mm avg th1ck(th1ckness will depend upor
the required slope and span of the building) M20 grade screeding anc
filling the panels with sealant(RMC for M20 screed will be supplied b~
the chentl Provide and applying Dr. F1x1t Fastflcx (2 component, pre packed
polymer modified cementitious coating, applied with a brush In 2 coat~
to achieve a DFT of lmm (consumot,on @ 1 Slners/Saml Waterproofing raft I
Cleaning a1 dirt, dust, loose material 1n order to i1Ch1evc J sound & dry
surface for applicat ion of waterproofing system. In case of pot
holes/crilcks, the same sh.i :I be repaired with cement putty admrxeo
with Dr F1x1t p;d,crete URP as per manufacturer's inst ruction. (Sano '
cement to be orov1ded free of cost at sltel Installat ion of 300 GSM Geotext ile layer over the PCC
Prov,dinc and apolylng wa ter proof,ns treatment w,th Mt!morane type
water proofing method using ETHYLENE PROPYLENE DIENE MONOMER
l.e EPDM membrane, Dr Fixlt Flexshaeld E60 of s,ze 6mX30 m roll of 1.52 mm thick having tensile strength of min 11 Mpa as per ASTM 0412 and
elongation at break m,n 1150% as per ASTM D 412, which 1s UV. IR and
Chemically resistant to certa,n chem ,ca s wh,cn are present n the sol
Seahnc all thl' overlapping Joints ol membrane with minimum 75· 100
mm overlap with the same two component bond.ng adhes,ve or tc1pe
like Dr F,xit Splice Adhesive or Double Sided Secure Tape which Is having
bond as per the manufacturer's methodology Installation of 300 GSM
Geotext1le as a protection layer over the waterproofing membrane
Protect tht' rncmbranl' oy prov1d1ng & laying screed concretl' of SOmm
thick over the geo· text e layer ensuring no damages to waterproofing
membrane bl'low (complete item 1n civ il contractor scope) I Waterproofing For Retaining w all I
The entire area shall oe taken up for thorough surface preparation w,th l
comprtt~scd .iir blow Jrid mechan,ca removal of debris, IJ1 tance, etc. It .
shal be wa terprooled wnh a mechanical spray applicauon at an average
thlckne~\ of I 5 mm with Dr F1x1t Fxtcnsa R , .:, water based, 1ero voe, ecofnendly, 2 part hybrid polymer based hqu1d membrane comprising of liquid base
and its catalyst. applied with a special twin nozzles compressed air
operated gun . This spray applied waterproofing membrane shall be
exhibit outstanding properties of adhesion onto the substrate with a
peel adhesion of at least ;>SN as per ASTM C 794 The membrane shall
adhere to the substrate within 60 seconds of application and shall
facilitate a wa lk over within S minutes of its insta latlon It ~hall possess
an elongation of at least 1000 % when tested in an independent
loboratory for extensib ih ty (ASTM D 41i) & give a full recovery after the
elongation. It shall possess a self-sealing
A BQ _311·. , 11 {I fl. ~ ~. {l. F-l. ,~. f;:1 · 3TI"m ~ - 1. :i.ITlT( I
.. ... ,
@ Unit Qty. Rate In Rs.
sqm 9585.00 1520.00
~ ~~-1--~~~~--11---~~~---l
' ,.. ~~ a. li. xi. r... ~. tR. 3fl1R1 ~ ,rJ - , . 3f Pm
SI. No. Description of Work Unit Qty.
property and be UV stable (ASTM G 155 for 1000 hours - accelera ted
weathering) . It shall exh1b1t a tear strength or at least 5 N / sq/mm. whe
tested for ASTM D 1004 and shall never puncture even if tested 1,
accordance wi th ATM E 154. st retched to the limit. W.iter permeabilit
in the said waterproofing material shall be nil as per BS EN 12390-8 & Sqm 5001.75
water vapor transmission shall not be more than 2 g/hr/ sq m. wher
tested as per ASTM E 96, and shall surpass the impact resistance test a lni>r 11.<TM n 'l74fi
s Providing & laying a protection layer over the wateroroofinc membranr I or 6 mm th1c~ expanded polyethylene board/dimple ooard befor1 Sqm 5000
backfill1nP I Providing & 1nstallat1on or aluminum terminat ion bar m1n1mum 150 mn I
6 above finished floor level & shall be fixed with non corrosive fastener @:
rmt 125 00 4 nos per RM And seal ng the termination bar w ith Dr F1x1t Lap Sealant
Providing ;ind grouting of all t,e rod cav,t es. Pipe penetrat ,ons and ar1\
other insert openings on retaining wa ll concrete using high strengtr 7 shrinkage compensated. free flow,..,g ccmen11t,ous grout mater1.i, Dr kg 225.00
F1x1t P1d1grout lOM having 24 days cornpressrve strength >65 N/mm2
I -I
N MISCELLANEOUS 1 Non shrink Compound ke 158036 25
2 Curing Compound for walls (Assume l lnre for lOsqrn) I lr tre 3959 00
3 Cold Joint Compond ll tre 5759 77
,1 tt l. < , ,I
~ (~1.) ~. v. ~ . f-1. ~-3fT"RT ~ r::....J -unr.n
~ ~• ~ o ~o ~ w ~ n
'31J1Rf~ - 1. 3fTlm . '''~·""'""'
@ Rate In Rs.
2013.00
439 00
628 00
31.00
24.00 55 00
1273 00
O INTERNAL & EXTERNAL PHE WORKS
S. No. Description Unit
A
1 (a)
(b)
(c)
2
(a)
(b)
(c)
3
(a)
4
(a)
(b)
5 (a)
(b)
6
(a)
{b)
7
(a)
8
{a)
{b)
9
(a)
10
INTERNAL PHE WORKS
SOIL WASTE, VENT & RAIN WATER PIPES AND FITIINGS
Providing and fixing soil waste and vent pipes
lOOmm diameter centrifugally cast (spun) iron S&S pipe as per 15:3989. Metre
7Smm diameter centnf ugally cast (spun) Iron S&S pipe as per IS:3989 Metre
150mm diameter Metre
Providing and fixing M .S. holder-bat clamps of approved design to and
cast iron centrifugally cast (spun) iron S&S pipes embedded in and
including cement concrete blocks lOx 10 x 10 cm of 1:2:4 mix (1 cem ~nt :
2 coarse sand : 4 graded stone aggregate 20mm nominal size) including
cost of cutt ing holes and making good the walls etc. For lOOmm diametre Each For 75mm d1amet re Each
For 150mm diametre Each
Providing and fixing bend of required degree w ith access door insertion
rubber washer 3mm thick, bolts and nuts complete
lOOmm centrifugally cast (spun) iron S&S as per IS:3989. Each
Providing and fixing plain bend of required degree:
l OOmm centrifugally cast (spun) iron S&S as per 15:3989. Each
75mm centrifugally cast (spun) iron S&S as per IS:3989. Each
Providing and fixing heel rest bend
lOOmm centrifugally cast (spun) iron S&S as per 15:3989. Each
75mm centrifugally cast (spun) iron S&S as per IS:3989. Each
Providing and fixing double equal plain junction of requi red degree.
100 x 100 x 100 x lOOmm centrifugally cast (spun) iron S&S Each
75 x 75 x 75 x 751nm centrifuga lly cast (spun) iron S&S Each
Providing and fixing single equal pl ain junction of required degree wi th
access door, insertion rubber washer 3mm thick, bolts and nuts com pl ->te
100 x 100 x lOOmm centrifugally cast (spun) ,ron S&S Each
Providing and fixing single equal plain junction of required degree.
100 x 100 x lOOmm centri fugally cast (spun) iron S&S Each
75 x 75 x 75mm cen trifugally cast (spun) iron S&S Each
Providing and fixing single unequal plain junction of required degree :
100x100x75 mm Sand cast iron S&S as per IS · 3989 Each
Providing and fixing door pieces 1nsert1on rubber washer 3mm thi k,
bolts and nuts complete I) --_l '""" .a .........
I~ ;q / ~ ~ . R1. ( ) \If tr'f '• J 'lj 4llf Ci I flJ. llll. )~'lllffl ~ L "- f;;. t-1. ~. 3fPffl ~. 3"'"1
P, j ') I ! "io U. ~. l.,u · •~ · 3Wm~-1.~1rrn
"o 'tfo ~r. r:.i~ r1. ft~). ~~ ... ~I~ - ' · ,r
® Quantity Rate In Rs.
400.00 871.00
100.00 751.00
570.00 1412.00
16.00 145.00
11.00 143.00
283.00 156.00
2.00 366.00
140.00 318.00.
7.00 236.00
2.00 353.00
1.00 297.00
2.00 710.00
1.00 530.00
2.00 592.00
124.00 547.00
1.00 385.00
1.00 655.00
~~ \J. Jl,. ~. ~o frto ~. 3ffTRT ~ - 1 . .3l'fTRI
(a) (b)
11 (a)
(b)
12
(a) (b) (c)
13
(u) (b)
14
(a)
15
(a)
(b)
16
(a)
17
(a) (b)
(c)
18
(a)
(b)
(c)
lOOmm centrifugally cast iron S&S as per IS: 3989. Each 75mm centrifugally cast iron S&S as per IS: 3989. Each
Providing and fixing terminal guard lOOmm centrifugally cast (spun) iron S&S as per IS: 3989. Each 75mm centrifugally cast (spun} iron S&S as per IS: 3989. Each
Providing lead cau lked joints to sand cast iron/centrifugally cast (<..pun)
iron pipes and fittings of diameter 150mm Each
lOOmm Each
75mm Each
Providing and fixing M .S. stays and clamps for sand cast iron/centrifugally cast (spun) iron pipe of diameter: lOOmm Each 75mm Each
Providing and fixing cast iron trap of self cleansing design with sand cast
iron screwed down or hinged grating with or without vent, arm compete,
including cost of cutting and making good the walls and floors
lOOmm inlet and lOOmm outlet centrifugally cast (spun) iron S&S as per Each
IS: 3989.
Painting sand cast iron/centrifugally cast (spun) iron soil, waste \ ent
pipes and fittings with paint of any colour such as chocolate, grey or l uff,
etc., over a coat of primer (of approved quality) for new work. lOOmm diametre pipe Metre 75mm d1ametre pipe Metre
Providing and laying in position cement concrete of specified gnde
excluding the cost of centring and shuttering - All work up to plinth level.
1:2:4 (1 cement 2 coarse sand : 4 graded stone aggregate 20 mm cum
nominal size)
Providing and fixing G.I. pipes complete with G.I. fittings and clamps
including cutting and making good the walls etc., (Internal work) : 32mm nominal bore Metre 50mm nominal bore Metre 80mm diameter pipe Metre
Painting G.I. pipes and fittings with two coats of anti-corrosive b1tuma lie
paint of approved quality. 32mm diameter pipe Metre
50mm diameter pipe Metre 80mm diameter pipe Metre
vfr.m $1.nn.~~ a. Ji.~ . .... .. ~. ~. ~ .. l<f>ll. 3lTrm
2.00 487.00 1.00 363.00
2.00 412.00
1.00 352.00
798.00 363.00
965.00 231.00 63.00 195.00
2.00 65.00 1.00 54.00
66.00 933.00
255.00 36.00 95.00 28.00
11.20 5192.00
90.00 326.00 55.00 500.00
45.00 605.00
90.00 9.00
55.00 13.00
45.00 19.00
19
(a) (b)
20 (a)
21
(a)
22 (a)
23 (a)
24
(a)
25
26
(a)
(b)
27
a)
b)
B
Providing, fixing and testing cast iron pipes (class 'LA' ) conforming to
IS:1536 complete with fittings such as tees, bends, crosses, clear,outs,
etc., lead caulked joints, steel supports as required/directed at site
including cutting and making good the walls, floors, RCC work, etc.,
cutting chases and filling the same wi th cemen t concrete 1:3:6 (1 cement
: 3 coarse sand : 6 graded stone aggregate 20mm nominal size) or ce nent
mortar 1:4 (1 cement: 4 coarse sand) as required (cost of structural steel
suooorrs & cleanouts shall be oa1d seoarntelvl. lOOmm diameter Metre
150mm diameter Metre
Providing and fixing plain bend of required degree: lSOmm centrifugally cast (spun) iron S&S as per 15:3989. Each
Providing and f1x1ng single equal plain junction of required degree w ith
access door, insertion rubber washer 3mm thick, bolts and nuts comr lete
150 x 150 x 150mm centrifugally cast (spun) iron S&S as per IS: 3989. Each
Providing and fixing single equal plain junction of required degree.
150 x 150 x 150mm centrifugally cast (spun) iron S&S as per IS: 3989. Each
Providing and fixing single unequal plain junction of required degree
150x150x100 mm Sand cast iron S&S as per IS · 3989 Each
Painting sand cast iron/centrifugally cast (spun) iron soil, waste ,ent
pipes and fittings with paint of any colour such as chocolate, grey or IJuff,
etc., over a coat of primer (of approved quali ty) for new work. lSOmm diametre pipe Metre
Providing and fixing lOOmm d1a G.I. Inlet f itting of standard design an las
shown in drawing with two-three inlets, suitable for 32mm to SOmm G.I. Each
Pipes and 75mm to lOOmm outlet.
Providing and fixing CP Brass floor cleanout plug as per drawing comp ete
with G.I. Socket jointed to drainage pipe outlet with lead caulked joint
100 mm dla Each
150 mm dia Each
Prov1d1ng and fixing cast iron Gratings for Rain Water Pipes.
lSOxlSOmm - Each
225x225mm - Each
INTERNAL WATER SUPPLY
~~ )'\f,.c.Of 4 '3fr. t:tlo I cG q c:"'1
~l---\fq -~r (Pl.)
\I. !.l'o ,) "1:.!f, f~i., rr:,, J11"1PT ~1( - 1 -r:-.;
T~ +?c.. • f .,qiffi
'3. tJ ~ . t-=t. ~. @T?l ~ . ;:.fl1R\
@
10.00 1344.00
415.00 2351.00
98.00 939.00
3.00 1904.00
7.00 1848.00
22.00 1683.00
885.00 32.00
66.00 933 .00
30.00 1423.00
22.00 2394.00
2.00 570.00
44.00 733.00
1 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, h wing
thermal stability for hot & cold water supply, including all CPVC pb in &
brass threaded fittings, including fixing the pipe with clamps at 1.JO m spacing. This includes jointing of pipes & fittings with one step -pvc solvent cement and testing of joints complete as per dlrecticn of
Emzineer in Charrze. Internal work· Exposed on Wall
(a) 15 mm nominal outer dia Pipes Metre 5.00
(b) 20 mm nominal outer dia Pipes Metre 25.00
(cl 25 mm nominal outer dia Pipes Metre 210.00
(d) 32 mm nominal outer dia Pipes Metre 190.00
(e) 40 mm nominal outer dia Pipes Metre 200.00 (f) 50 mm nominal outer dia Pipes Metre 140.00
(g) 6Smm nominal outer dla pipes (SCH-40 ASTM F-441) Metre 340.00 (h) 80mm nominal outer dia pipes (SCH-40 ASTM F-441) Metre 155.00 (i) lOOmm nominal outer dia pipes (SCH-40 ASTM F-441) Metre 20.00
2 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, h, ving
thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fitt ings, i/c fixing the pipe with clamps at 1.00 m spa 1ng.
This includes jo inting of pipes & fittings wi th one step CPVC so lvent
cement and the cost of cutting chases and making good the s.Jme
including testing of joints complete as per direction of Engineer in
Charee. Concealed work, including cutting chases and making good the walls
etc. (a ) 15 mm nominal outer dia Pipes Metre 110.00 (b) 20 mm nominal outer dia Pipes Metre 120.00
(cl 25 mm nominal outer d1a Pipes Metre 190.00
(d) 32 mm nominal outer d1a Pipes Metre 80 00 (e) 40 mm nominal outer d1a .Pipes. Metre 30.00 ( f) 50 mm nominal outer dia .Pipes. Metre 5.00
3 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, ha 11ng
thermal stabilit y for hot & cold water supply including all CPVC pla 1"1 &
brass threaded fittings This inc ludes jointing of pipes & fittings with one
step CPVC solvent cement ,trench ing ,refi ll ing & testing of jo nts
comolete as oer direction of Engineer in Charge. External Work
(a) 25mm nominal outer d1a pipes Metre 5.00
(b) 32mm nominal outer d1a pipes Metre 5.00
(c) 7Smm nominal outer dia pipes Metre 10.00
~ii1f ij[Jk,-~
·-~ - ~~~.
... ~o ~1. ~• frl, f." .. ~ ~ - 1, 3ffff~I
~. \':lo i'l. P.. f.1 1~·1.,
~ ~ - 1 . .... l l'J":
0 ~ '.r?' .1. ~ r-.. I? 1" ,i $~,J ,, I
155.00 181.00
219.00
281.00 387.00 552.00
1416.00
1788.00 2473.00
256.00 281.00 333.00
401.00 458.00 763.00
199.00
249.00 1948.00
4
(a)
5 (a) (b)
(cl (d)
(e)
( f)
(g)
6
(a)
(bl
7
(a)
(bl (c)
8
(a)
(bl
9
10
(a)
(bl (c)
(d)
(e)
(f)
Constructing masonry chamber 30x30x50 cm inside with 75 class
designation brick work in cement mortar 1:4 (1 cement: 4 coarse and)
for stop cock with Cl surface box 100 x 100 x 75mm with hinged t Over
fixed in cement concreting slab 1:2:4 (1 cement: 2 coarse sand: 4 grJded
stone aggregate 20mm nominal size). necessary excavation found ation
concrete 1:5:10 mix (1 cement: 5 fine sand:10 graded stone aggrega e 40
mm nominal size), and inside plastering with cement mortar 1 3 (1
cement · 3 coarse sand) 12mm thick finished with a floating coal of ,eat lcement comolPtP as nPr stanrlard rlPc;11,n With F.P .S. bricks Each
Providing and fixing lever operated gun metal ball valve with SS ball.
lSmm nominal bore Each
20mm nominal bore Each
25mm nominal bore Each
32mm nominal bore Each
40mm nominal bore Each
SOmm nominal bore Each
6Smm nominal bore Each
Providing and fixing cast iron Wafer Type Butterfly valve of the follo\:1ing
size complete with bol ts, nuts, washers and neoprene gaskets as per
specifications. 80 mm dia Each
100 mm dia Each
Providing and fixing ball valves with plastic float for inlet for w 1ter
storage tanks. 2Smm dia Each
32mm dia Each
6Smm d1a Each
Extra for providing and fixing class-0 Kai flex ST insulation 6mm thic to
hot water pipe and fittings and valves as per manufactu rr>r's
recommendations complete to satisfaction of Engineer in charge. lSmm nominal bore Meter
20mm nominal bore Meter
Providing and fixing heavy duty circular manhole cover with frame .1ze
525mm dia, total weight SO kg (25 kg cover and 25 kg frame) completL· 1n Each
all respects. (For overhead tanks).
Providing and fixing 600mm long puddle flanges fabricated out of 6mm
thick M .S. plates along with flanges of suitable size properly fixed in w c1 lls
and top slabs of underground and overhead tanks.
25mm dia Each
32mm dia Each
40mm dia Each
SOmm d1a Each
65mm dia Each
80mm d1a 0 JI/' ' Each
.~ · ~~flf~I (~ .)
A~ \i'Q ~ ,t1 ~ l (fo.)
' ':, .. >f,, xi. f-1 ~. {" ,, ~ idiS - 1,~m(1
~-~ •· !;J. xr. ~ .. ~ .. f ~ ~ - 1, 3Wi·!I
1'1T. "11. - r f
"· .. 'I. ~ f .. ;, . ~ -
.
4.00 1099.00
1.00 432.00
5.00 561.00
9.00 821.00
10.00 1338.00
11.00 1862.00
12.00 2698.00
6.00 5612.00
2.00 284 7.00
1.00 3680.00
1.00 2188.00
1.00 3085.00
2.00 9702.00
20.00 152.00
10.00 175.00
10.00 3906.00
9.00 323.00
14.00 378.00
5.00 424.00
5.00 528.00
5.00 696.00
5.00 889.00
~ "G". ti. x'I. ~. f.l. ~. 3JTlRT. ~ - 1, 3fT1ffl
(g) (h)
11
c
1
2
3
(a)
4
(a)
5
lOOmm dia
lSOmm dia
Providing and fixing lOOmm dia G.I. vent pipe on Under ground and over
head tank inlcuding cost of 2 Nos. 90° bend and paint ing with enamel
paint complete with in all respect.
SANITARY FIXTURES
Providing and fixing white colour vitreous china wall mounted (Euro Jean
style) water closet ROCA wall hung water closet cat no.-RS346237000
and soft close seat cover cat no. · RS801230004 with Vitreous C1ina
flushing cistern with fitt ing brackets and overflow pipe wi th mosc ui to
proof coupling of and approved design {ROCA cat no. RA890031410)-.vi th
CP bolts & nut!>, solid white plastic seal and lid, CP brass hinges and
rubber buffers, and clamps all complete, including cutting and maKing
Pnod the walls and flnnrs wherever renuired.
Providing and fixing white glazed vitreous china flat back ROCA make
model No-RS3594SLOOO with Urinal Sensor model No-RTSX9315EOO
with C.I. hangers with built-in electronic solenoid valve operated uto
flushing system complete with all electrical works required for
completion of work, wi th f itt ings concea led in chase, C.P. sprearers,
32mm C.P. brass domical waste, 32mrn C.P. cast brass screws and
washers complete including cu tt ing and making the wc1lls and fi e ors
where reauired.
Providing and fixing white glazed vitreous china wash basins with P.
pillar tap, C.P. brass waste 32rnm C.P. bottle trap and unions and sea ing
of joints between wash basins and coun ter slabs around the wash ba ins
with Si licone rubber cement of approved make of matching colour all
complete including cutting and making good the walls and floors where
reauired.
ROCA make Cat. No. RS327884000 (Under counter) wi th C.P. single
level basin mixer Jaquar Cat No. 15011, C.P. brass waste Jaquar Cat. No .
ALD-709 & C.P.bottle trap ROCA Cat. No. RF9066Al
Providing and fixing C.P. brass bib taps long body ROCA Cat.
No.RTSA7825CA1 including cutting ond making good the walls where ,er
required .
Long Body
Providing and fixing stainless steel sink w ith MS or Cl bracket, stainlt ss
steel basket waste and plug 40mm CP cast brass bottle trnp with pipe to
wall CP wall flange, Jaquar Cat. No. 767 or equivalent mc>l<e
Parka/Kingston rubber adop ter for waste connection complete, includ,-,g
cutting and making good the walls where required.
~· iitf~ (rtf.)
~JI. ~. r,;~ ~ .. ~I ..
~~ - 1. 3lflh:1
Ak) iiif~ ;:ff ·l~I (ti. . (' Ii. 'Q., ~ , 1.,~ H .. !,
~ r , ; - , . .-,1 :,:,
® Each 12.00 1413.00
Each 2.00 2324.00
Each 10.00 4319.00
Each 65.00 34163.00
Each 31.00 32291.00
Each 44.00 13938.00
Each 65.00 2092.00
(a)
(bl
6
7
8
9
10
]l
12
a)
b)
Single bowl w ith single dra in board overall size 940mm x 465mm x
178mm deep or nearest commercial size available JAYNA or equiva1ent make NIRALI -Elega nee-Sm a II/Kl NGSTON-Cobra-Kavarl(SBD) with CP brass mixing fittings Jaquar Cat. NO. CON-309KN, C.P. brass waste
Each Jaquar Cat. No. ALD-709 & C.P. bottle trap Jaquar Cat. No. ALD-7698 or
equivalent make CP brass mixing PARK0-1526/KINGSTON-AGR 604, <. P.
brass waste/ PARK0-1544/KINGSTON-AGR 2007, C.P. bottle trap PARKO 1535/KINGSTON-AGR 2003.
Double bowl with Single drain board JAYNA Mercury Cat. No. DBSD 02 (DX) overall size 1690mm x 510mm x 200mm deep or near est
Each commercial size available AMC or approvaled equivalent with CP brass
mixing fittings Jaquar Cat. NO. 309 or approved equivalen t.
Providing & Fixing 6mm thick looking mirror of Modi float glass/Atul/-· -··
make fixed on 25 dia and 38mm long ss studs, the studs shall be fixed on Sqm. wall /tile with dash fastener complete.
Providing and fixing C.P. brass towel ring JAQUAR Cat No. ACN-1121N
(CONTINENTAL SERIES) or approved equivalent complete with C.P. brass Each
brackets fixed to rawl plug of approved design with C.P . brass screws.
Provid ing and fixrng C.P. brass twin robe hooks, JAQUAR Cat . No. 1161 or Each
equivalent make PARKO-Classic-1582/KINGSTON-AGR ACS 66.
Providing and fixing lSmm C.P. brass angle valve with C.P. br,ss connection pipe Jaquar Cat No. CON-0531<N & ALD-8038 or equivalent
make PARKO-Classic-15198/KINGSTON-AGR ISK 04 & pipe AGR 401, Each union nuts complete with C.P. brass flange including cutting and making
!good the walls wherever reauired.
Providing and fixing stainless steel toilet paper ho lder JAQUAR Cat. No.
ACN-1151N or equivalent make PARKO-Classic-1553/KINGSTON-AGR
ACS 20 fixed in position by means of C.P. screws and rawl pl LJgs Each
embedded In the walls complete including cut t ing and making good the
walls wherever reauired.
Providing and fixing S.S. hinged grating, 6mm thick with frame (Neer Cat . No. - NRG 7008 or equivalent make CHILLY-CCT-SC-156 (Square
Each Classlc)/ CAMRY-SKDH-150 including setting in floor with cement mor ar 1:3.
Providing and fixing automatic high pressure electric water heaters HAVELLS-Monza or equivalent make VENUS-Magma-Vertical
2SGV/ RACOLD-Etrno·2 ER2 with glass lining thermostats with e.ich
element and high temperature cut off, necessary insulation, safety val\ e, etc. all comolete. 15 litres Each 25 li tres Each
~ I ~Al I Gnn~~ .. '
rq3 II~
'• · ~o ~ i. I~. r-'lv ~ I
~ ~~ - 1, -lWNi
\l' c: ·q, l~ C!"' I r-rm. ~,. ~ .f
\l ~. ~ ~ • t n , •
,..,. - .. -<r,c .,
2.00 12678.00
2.00 23902.00
50.00 3052.00
20.00 1121.95
65.00 615.60
182.00 1224.00
65.00 766.00
107.00 957.00
2.00 9610.00 2.00 10704.00
13 Providing and Fixing Health Faucet JAQUAR Cat. No. 573 (ALLIED SERIES)
or equivalent make PARKO-Allied-1597 / KINGSTON-AGR ACS 49 wi th Each
flexible pipe and wall hook wi th each European W.C. Pan.
14 Providing and fixing, Glass Bot tle Liquid Soap Dispenser wi th push ever
assembly complete with soap refill - (JAQUAR Cat No. ACN-1135N) M ake Each
or approved equivalent.
15 Providing and fixing white glazed vitreous china Division Plates for urinals
(H.S.I. Cat no. 61001 or approved equiva lent) of size 680x 300 mm. Each
EXTERNAL PHE WORKS
D SEWERAGE SYSTEM
1 Providing, laying and Jointing glazed stoneware pipes class SP-1 with st iff
mixt ure of cement mortur in the proport ion of 1:1 (1 cement : 1 fine
sand) including testing of joints etc complete :
(iJ) 100 mm diameter Metre (b) 150 mm diameter Metre
2 Providing und laying cement concrete 1:5:10 (1 cement: S coarse sand :
10 graded stone aggregate 40 mm nominal size) all-round S.W. p pes
including bed concrete as per standard design:
a) lOOmm dia SW pipe Metre
b) 150mm dia SW pipe Metre
3 Providing and laying non-pressure NP2 class (ligh t duty) R.C.C. pipes wi th
collars jointed with stiff mixture of cement mortar in the proportio 1 of
1:2 (1 cement : 2 fine sand) including testing of 1oints etc. complete:
a) 150mrn dia RCC pipe Metre
b) 250mrn dia RCC pipe Metre
4 Providing and laying cement concrete 1:5:10 (1 cement: 5 fine sand 10
graded stone .iggregate 40rnm nominal size) all-round S.W. pipes
including bed concrete as per standard design.
a) 150mm dia RCC pipe Metre
b) 250mm dia RCC pipe Metre
5 Providing and fixing square-mou th S.W. gully trap class SP-1 complPte
with C.I. grating brick masonry chamber with water tight C.I. cover w th
frame of 300 x300 mm si7e (inside) the weigh t of cover to be not I ss
than 4.50 kg and frame to be not less than 2. 70 kg as per standard des gn
150 x lOOmm size P-type
a) With common burnt clay F.P.S. (non modular) bricks of class designation
7.5 Each
,/ fl c --~ ' I
.,, .... ~ l "> -~
~---1-'fll (mo) J . ,,.. .... Q . .. ~l. ~- f.!. f;·
/~01 -\lti~
~. ~. xi. f-1. f.'t~ 3ll1N{~~ - 1, 3ffli~l
~~~- 1.~PW
® 65.00 1976.00
20.00 1299.00
25.00 3015.00
20.00 196.00
40.00 298.00
20.00 562.00
40.00 688.00
215.00 330.00
140.00 445.00
215.00 688.00
140.00 928.00
10.00 1514.00
I
~ ~~~
'3'. 11. x'I. ~- f.'!. fR. 3fTTRl ~i ·- l :~PHl
6 Const ructing brick masonry manhole in cement mortar 1:4 ( 1 cemen t : 4
coarse sand ) with R.C.C. top slab with 1:2:4 mix (1 cement : 2 co Jrse
sand : 4 graded stone aggregate 20 mm nominal size), founda .ion
concrete 1:4:8 mix (1 cement: 4 coarse sand : 8 graded stone aggrecate
40mm nominal size), inside plastering 12mm thick with cement mortar
1:3 (1 cement : 3 coarse sand) finished with f loating coal of neat cen ent
and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sJnd
: 4 graded stone aggregate 20mm nominal size) finished with a floa ting I coat of neat cement comolete as nPr c;t.:inrl.:irrl rloc;ii:,n Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (1 ,ght
duty) 455x610 mm internal dimensions, total weight of cover and fr 1me
to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg):
a) With common burnt clay F.P.S. (non modular) bricks of class designa ,on Each 7.00 8081.00 7.5
7 Extra for depth for manholes:
Size 90 x 80 cm
With common burnt clay F.P.S. (non modular) bricks of class des1gnai 1on Metre 0.50 5356.00 7.5
8 Constructing brick masonry circular type manhole 0.91 m internal du at
bottom and 0.56m dia at top in cement mortar 1:4 (1 cement :4 cot1rse
sand), in side cement plaster 12 mm thick with cement mortar 1: (1 cement : 3 coarse sand) finished with a floating coat of neat cement,
foundation concrete 1:3:6 mix (1 cement: 3 coarse sand: 6 graded stone
aggregate 40 mm nominal size), and making necessary channel in cement
concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate: 20
mm nominal size) finished with a floating coat of neat cement, all lrf'\mnlPtP ;ic; oer standard dPc;iim ·
0.91 m deep with S.F.R.C. cover and frame (heavy duty, HD-20 grade
designation) 560 mm internal diameter conforming to I.S. 12592, total
weight of cover and frame to be not less than 182 kg., fixed in cement
concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20
mm nominal si2e) including centering, shuttering all complt:te.
(Excavation, foot rests and 12mm thick cement plaster at the external
surface shall be oaid for seoaratelvl: a) With common burnt clay F.P.S. (non modular) bricks of class designa t on
Each 3.00 8301.00 7.5
9 Extra depth for circular type manhole 0.9lm internal dia (at bottom)
beyond 0.91 m to 1.67 m
a) With common burnt clay F.P.S. (non modular) bricks of class des1gnat on Metre 1.00 4600.00
7.5
\:¥,~ -un. ~ ~~en .. ..,, '11 ~ .
'3. . ., - '
~~ ·· ~ -
10 Constructing brick masonry circula r manhole 1.22m internal dia at
bottom and 0.56m dia at top in cement mortar 1:4 (1 cement :4 coar se
sand) inside cement plaster 12mm thick with cement mortar 1:3 (1
cement :3 coarse sand) finished with a floating coat of nea t ceme i t
foundation concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded sto "le
aggregate 40mm nominal size) and making necessary channel in cement
concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate
20mm nominal size) fin ished wit h a floating coat of neat cement, JI! comolete as oer standard dPc;iP.n · 1.68 m deep with SFRC Cover and frame (heavy duty HD-20 grade
designation) 560mm internal diameter conforming to I.S. 12592, total
weight of cover and frame to be not less than 182kg. fixed in cemeri t
concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate
20mm nominal size) including centering, shuttering all complete.
(Excavation, fool rests and 12 mm thick cement plaster at the exterr al
surface shall be oa1d for seoaratelv\ · a) Wi t h common burnt clay F.P .S. (non modular) bricks or class designation
Each 9.00 15644.00 7.5
11 Extra depth for circular type manhole l.22m internal dia (a t bottom )
beyond 1.68 m to 2.29 m :
a) Wit h common burnt clay F.P.S. (non modular) bricks of class des ignatio n Metre 17.00 5957.00
7.5
12 Providing orange colour safety foot rest of minimum 6 mm thick plas11c
encapsulated as per IS: 10910 on 12mm dia steel bar conforming to I~:
1786 having minimum cross section as 23 mmx25mm and over ill minimum length 263 mm and width as 165mm with minimum 112 mm
space between protruded legs having 2 mm tread on top surface JY ribbing or chequering besides necessary and adequate anchoring Each 108.00 296.00 proJect ions on tail length on 138 mm as per standard drawing and
sui table to with stand the bend test and chemical resistance test as per
specifications and having manuf acture's permanent identifica tion mark
to be visible even after fixing, including fixing in manholes with 30x20x 5
cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 3radLd c:. tnnP ;iu1:,rpo;:itp ?n mm nnmin;:i l c;j7p\ rnmnlPtP ;:ic; ni:>r rii:><:ion
13 Earth work in excavation by mechanical means (hydraullic excavator) I manual means over areas (exceeding 30cm in depth. 1.Sm in width JS
well as 10 sqm on plan) including disposal of excavated earth lead up o
SOm and lift upto l .Sm, d isposal earth to be levelled and neatly dressed
a) All kinds of soil Cum 134.00 147.00
14 Fill ing available excavated earth (excluding rock) in treanches, pl inth,
sides of foundations etc. In layers not exceeding 20cm 1n deplt ., Cum 19.00 106.78
consolidating each deposited layer by rammine and watering, lead up o SOm and lift uot l.Sm.
-~ ~~ ~- ,7J ;:, ~
lie ~o '( lo t";!j. f "1~ ft '. • '3. >' •,
~~~ •. ~Tf9~
CM) 15 Excavating trenches of required width for pipes, cables, etc including
excavation for sockets, and dressing of sides, ramming of bottoms, depth
upto 1.5 m including getting out the excavated soil, and then returning
the soil as required, in layers not exceeding 20 cm in depth, incl iding
consolidating each deposited layer by ramming, watering, etc and
disposing of surplus excavated soil as directed, within a lead of 50 m
All kind of soils Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm d a. Metre 400.00 197.00
16 Extra for excavating trenches for pipes, cables etc in all kinds of so I for
depth exceeding 1.5 m, but no t exceeding 3 m. (Rate is over
corresponding basic item for deoth uoto 1.5 metre).
a) Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm d a. Metre 170.00 267.00
E EXTERNAL WATER SUPPLY SYSTEM
1 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having
thermal stability for hot & cold water supply including all CPVC pla ·1 &
brass threaded fittings This includes Jointing of pipes & fittings with one
step CPVC solvent cement ,trenching ,refilling & testing of jc nts comolete as oer direction of Engineer in Charne.
External Work
a) 2Smm nominal outer dia pipes Metre 150.00 199.00 b) 32mm nominal outer dia pipes Metre 30.00 249.00
c) 40mm nominal outer dia pipes Metre 55.00 332.00
d) 50mm nominal outer dia pipes Metre 520.00 497.00
e) 62.Smm nominal outer dia pipes Metre 765.00 1389.00
f) 75mm nominal outer dia pipes Metre 210.00 1948.00
g) lOOmm nominal outer dia pipes Metre 200.00 2693.00
2 Providing and fixing CI. double acting air valve of approved quality v. 1th - bolts, nuts, rubber, insertions etc. complete (The tail pieces, tapers et if
required will be paid separately). a) 50mm dia Each 4.00 4539.00
. 3 Const ructing masonry Chamber 30x30x50 cm inside, in brick work in
cement mortar 1:4 (1 cement :4 coarse sand) for stop cock, wrth C I.
surface box lOOxlOO x75 mm (inside) with hinged cover fixed rn cem( nt
concrete slab 1:2:4 mix (1 cement : 2 coarse sand · 4 graded sto1e
aggregate 20 mm nominal size), i/c necessary excavation, foundati.::,n
concrete 1:5:10 ( 1 cement : 5 fine sand : 10 graded stone aggreg .. te
40mm nominal size ) and inside plastering with cement mortar 1:3 (1
cement : 3 coarse sand) 12mm thick, finished with a floating coat of neJt lri>ment comolete as oer standard desi11n ·
a) With common burnt clay F.P.S (non modular) bricks of class designatic n Each 20.00 1099.00
7.5
. / CJ (_- ........ ~! 3tnw,a, ~ lk
'i. Qo -(I. r-,. f.t. ,;:,,
,rf1, tfi' 1%11Gj ~ ~1 ' t,rn
i ; ~ ~'" I, 3il t'(! ,n'7' .
4 Constructing masonry Chamber 60x60x75 cm inside, in brick wo k 1n
cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, wit 1 C.I.
surface box lOOmm top diameter, 160 mm bottom diameter and 18(; mm
deep ( inside) wi th chained lid and RCC top slab 1:2:4 mix (1 cemer t : 2
coarse sand : 4 graded stone aggregate 20mm nominal size ) i/c
necessary excavation, foundation concrete 1:5:10 (1 cement: 5 fine sand
: 10 graded stone aggregate 40 mm nomimi l size) and inside plastering
with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, fin , hed
wi th a floating coat of neat cement complete as per standard design
a) With common burnt clay F.P.S (non modular) bricks of class design ... tion Each
7.5
5 Constructing masonry Chamber 90x90xl00 cm inside, in brick wo k in
cement mortar 1:4 (l cement : 4 coarse sand) for sluice valve, wit~ C.I.
surface box 100 mm top diameter, 160 mm bottom di.imeter and 180
mm deep (inside) with chained lid and RCC top slab 1:2:4 mix (1 cemPnt :
2 coarse sand : 4 graded stone aggreg.ite 20 mm nominal SIZe ) i/c
necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine and
· 10 graded stone aggregate 40 mm nominal S1Ze ) and 1ns1de plastering
with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, fini<hed
with a floating coat of neat cement complete as per standard design :
a) With common burnt clay F.P.S (non modular) bricks of class designation
7.5 Each
6 Providing and fixing lever operated gun metal ball valve with SS ball.
a) 25mm nominal bore E.ich
b) 32mm nominal bore Each
c) 40mm nominal bore Each
d) SOmm nominal bore Each
e) 65mm nominal bore Each
7 Providing and fixing C.I. Butterfly valves conforming to PN 1.6/13095
with nuts, bolts, washers, 3mm thick insertion ruber gasket and •wo
matching flanges as per table 'E' etc. complete .
a) 80mrn nominal bore Each
b) lOOmm nominal bore Each
F RAIN WATER HARVESTING CHAMBER (3 NOS.)
1 Boring/drilling bore well of required dia for casing/ strainer pipe, by
suitable method prescribed in 15:2800 (part I), including collect ng
samples from different strata, preparing and submitting strata chart/bore
log, including hire & running charges of all equipments, tools, plant &
machineries required for the job, all complete as per direction of
Engineer-in charge, upto 90 metre depth below ground level.
a) All types of soil
300 mm dia Metre
.,
(;
~qlftf,-- d~
~
ii. Uo ~. frto ~o ; 3fT1'R( ~ - 1. 3!Tl, ~!
'
~. >lo xl. f.!l. f.=,, !~ ~n
~,; :-::,"-· "11
~, J I .,,
I '
8.00 6416.00
4.00 11088.00
20.00 821 .00
1.00 1338.00
1.00 1862.00
5.00 2698.00
3.00 5612.00
2.00 2847.00
2.00 3680.00
120.00 386.00
/
~ti ~~
\Je Jl. x'Jo ~o fr!. ~ • 3lJ7ffi ~d - 1, '1f'T'Tr{J
2 Supplying, assembling, lowering and fixing in vertical position in bore
well, ERW (Electric Resistance Welded) FE 410 mild steel screwec and
socketed/ plain ended casing pipes of required dia, conforming o IS:
4270, of reputed & approved make, including painted with Ol tside
surface with two coats of anticorrosive paint of approved branCI and
manufacture, including required hire & labour charges, ftttin ,s &
accessories, all complete, for all depths, as per direction of Engine r-in-
lcharo~. a) 150 mm nominal size dia having minimum wall thickness 5.00 mm Metre 60.00 1268.00
3 Supplying, assembling, lowering and fixing in vertical positron in ~ore
well, ERW (Electric Resistance Welded) FE 410 plain slotted (havinp slot
of S1Ze 1.6/3.2mm) mild steel threaded and socketed I plain level e 1ded
pipe (type A) of required dia, conforming to IS: 8110, of reputed and
approved make, having wall thickness not less than 5.40 mm, including
painted with outside surf ace with two coats of anticorrosive b1tum •stic
paint of approved brand and manufacture, including hire & laoour
charges, fittings & accessories, all complete, for all depths, as r:,er :nirPrtion of FnPinPPr-in-rh::1rgp
a) 150 mm nominal StZe d1a . Metre 60.00 1347.00
4 Providing and fixing bail plug/Bottom plug of requ ired dia to the bottom
of pipe assembly of tubewell as per 15:2800 (Part-I) . a) 150 mm dia Each 3.00 230.00
G MISCELLANEOUS WORKS
1 Providing and fixing medium duty circular manhole cover with frame ~ize
500 mm d1a, total weight 128 kg (64kg frame & 64 kg frame) complete in Each 8.00 10355.00
all respects. (For underground tanks & overhead tanks
2 Providing and fixing 600mm long puddle flanges fabricated out of 6rn m
th ick M .S. plates along with flanges of suitable size properly fixed in w1 lls
and top slabs of underground and overhead tanks.
a) 25mm d1a Each 8.00 323.00
b) 32mm d1a Each 75.00 378.00
c) 40mm dia Each 30.00 424 .00
d) SOmm d1a Each 70.00 528.00 e) 65mm dia Each 30.00 696.00
f) 80mm dia Each 10.00 889.00
g) lOOmm dia Each 95.00 1413.00
h) lSOmm dia Each 5.00 2324.00
1) 200mm dia Each 5.00 2429.00
3 Providing & fixing GI vent pipe complete with 2 Nos. bends complete w th
mosquito proof wire mesh & painting with enamel paint all comple te.
a) 100 mm dia Each 8.00 4319.00
4 Providing and fixing MS foot rests with 20x20mm sq. bars (for Each
underground tanks & overhead tanks).
H PUMPING SYSTEM
1 Providing, fixing, testing and commissioning of Vertical in line type rump
set with SS casing, SS impeller and SS shaft suitable for operation on
400/440 volts, 3 phase 2900 RPM, TEFC electric motor mounted on a
common channel base plate with coupling guard, 150mm dia pre sure
gauge, GM 1solat1on cock and cement concrete foundation with pldster
comolete as reau1red. a) Filter Feed pumps
Pump capacity 200 lpm
Head - 25 m
RPM · 2900 Each
b) Domestic water transfer pumps
Pump capacity · 400 lpm
Head - 40 m
RPM • 2900 Each
c) Flushing water transfer pumps
Pump capacity • 200 lpm
Head · 40 m
RPM · 2900 Each
2 Providing, fixing and comm1ss1oning non clog type mono bock
submersible drainage pumps suitable for handling solids of 12 mm me
with totally wa ter and dust proof motor as specified complete with m Jtor
control panel and float switch, inclusive of all terminations and eart , 1ng
required all comolete as oer soecifications. a) Capacity 200 lpm & Head 10 m (in pump room) Each
b) Capacity 300 lpm & Head 10 m (in basement) Each
3 Providing, fixing and commissioning non clog type mono b eek
submersible drainage pumps suitable for handling solids of 32 mm ,ze
with totally water and dust proof motor as specified complete with me tor
control panel and float switch, Inclusive of all terminations and earthing
required all comolete as oer soecifications. a) Capacity 100 lpm & Head 10 m (in basement) Each
4 Providing and fixing Transistorised liquid level controllers with ow
vol tage Relays and Seamless Steel probes and PVC shroud, incluc.1ng
necessary wiring and conduiting f rem probes to display panel/me tor
con trol panels and to provide Audible Alarm for low level for each
underground tank . (The cost of all required cabling from probes to Ml tor
control oanels to be including in the rate). a) For Domestic Fil ter feed
To start domestic filter feed pumps at low water level in domestic trea ted
under ground tank and stop at high water level in domestic trea ed Set
treated tank and stop at low water level in domestic raw water tank
TdZ- ' ~ ·-I
~i ~~ A, ~
jJJ, ~ • .,,f~HT"\11
~. ~. xlo ~• ~• f 31T7TW ~ - l .. Jrrr,•,
'4. ~- xi. f ·t f·\ iv! ..
~~"1'.,; - '. ,,i!•I"-
•• ,. ~. f • ~- ~. ~~. JWm
50.00 475.00
2 59076.00
2 103716.00
2 59076.00
2 32293.00
8 43453.00
4 36757.00
1 9821.00
l~~ \J. Jl. xT. ~- f.'i. ~-3l'J'TRI ifcf>rl - 1. 3fP m
b)
s
5.1
a) 1)
ii)
iii)
iv)
v)
b)
c)
i)
ii)
iii)
iii)
iv)
v)
vi)
vii)
viii)
a)
b)
5.2
a) b)
c)
For Domestic water transfer pumps
To start pump at low water level in overhead tank and stop at high\ ater Set
level in overhead tank and low water level in under ground tank.
Supply, installation, testing and commissioning of the foll owing
integrated, cubicle type, dead fornt, extensible, sheet steel control p..:1nel 1
to the foundation The panel shall be suitable for 415 volts, 50 cyc l ~s, 4
wire supply . Quoted price shall be including wi th 25mm thick ru ober
mats, wiring, cabling of approved size, control wiring and copper earthing
from control panel to various equipment like motor starters, pump
motors etc. including making end terminations etc. The follO Ntng
components and accessories shall be mounted within each control panel.
For water supply pumps
One No. 63 amps TP incoming MCCB complete with the following:
1 No. 0-500 volts 96x96 sq . mm ammeter with selector switch and ft ses.
(1 set) . 1 No. 0-100 amps 96x96sq.mm ammeter with 60/5 amps ratio CT' s and
selector switch.
Over voltage and under voltage tripping machan1sm for persis ent
voltage fluctations of more than ±10% of the rated voltage for more than
5 minutes. (lset) Phase indicating lamps with toggle switches.
Indication lamps for ON/OFF/TRIP status of motors.
Aluminium bus bar of 63 amps for three phase and neutral.
Outgoing Feeders/Starters.
16 amps TPN MCB with DOL starter with built-in SPP each suitable 2 HP
filter feed pumps (2 Nos).
16 amps TPN MCB with DOL starter with built-in SPP each suitable 5 HP
domestic water transfer pumps (2 Nos).
16 amps TPN MCB with DOL starter with built-in SPP each suitable 3 HP
flushing water transfer pumps (2 Nos).
16 amps TPN MCB with built-in SPP e.ich suit.ible for 2 HP dra in 1ge
pumps panel in basement(4 Sets). 16 amps TPN MCB with built in SPP each suiluble for 1 HP dra1n.1ge
pumps panel in pumproom(l Set). 16 amps TPN MCB with bu1lt-1n SPP each suitable for 1 HP sewer. ge
pumps panel in basement (2 Sets).
16 amps TPN MCB with built-in SPP each suitable for 3 HP tubev ell
pumps panel (lSet) .
Rotary manual/auto/off switch. (4 Nos.)
Spares .
16 amps TPN MCB · 2 Nos.
32 amps TPN MCB · 2 Nos. Set
For drai nage pumps panel in pump room
16 amps incoming MCB (1 No.)
Fully tapped Copper bus bas of suitable capacity. (1 set)
Panel type volt meter 96mm square with Rotary selection switch or
reading voltage between phase and neutral or incoming feeder. (1 set)
,fl .. ~K.:!· ii. 'Q'o ~ I. Flo ~1. r· ~~- 1. Jlfll~I
~ '-·\.Jo -;,'~ I-! .. I·\! awm ~t,~..; - I \lJ 1r;r f
'1~1. '1f!. .111'iHf~·1} 11• 'Q, '{J . f\ t 1 r~~,. .. ... y ... ~.;; r.f 11·1'11
1
1
µID
9821.00
69369.00
~~ '3o IL ~. f3o f:i. ~. iflTRT ~ - 1, 3fT7R I
d) Phase indicating lights wi th toggle switches and shall be protected by 2
amps MCB's. (2 sets) e) Ampere meter 96mm square panel type of appropriate range. (1 set)
f) 16 amps outgoing MCB (2 Nos.)
g) Fully automatic DOL starters with push buttons indicating l ights and
overload relay each for drainage pump. (2 Nos.) h) Single phasing preventors. (2 Nos.)
i) Rotary manual/auto/off switch. (2 Nos.) j) Space of one liquid level controller Set
6 Supplying and laying the PVC insulated & sheathed FRLS Armoured cables
of 1.1 K.V. Aluminium Conductor on prelaid cabel trays including
supplying and making and term ination with brass compression glands:
(cabel trays shall be installed by electrical cotrator). a) 3 Core x 4 sq.mm b) 3 Core x 6 sq.mm
I WATER TREATMENT SYSTEM
1 Providing and fixing skid mounted vertical MSRL Dual Media pressure
filter fabricated from IS 226/2062 plate Smm thick for shell and 6mm
thick M.S. plate for dished ends complete with initial charge of filter
media, face piping and valves accessories, painting, testing and
commissioning comolete.
a) For Domestic water supply
Capacity 12000 lph.
Working pressure 2.5 kg./cm2
Design pressure 4 kg./cm2
2 Providing and fixing bulk water meter with direct reading dial in KL, all
internal parts and strainer in gun metal/brass.
Metre
Metre
Each
a) 65mm dia Each
3 Providing and fixing direct reading rate of flow Rota Meter
a) For 65mm dia for 12000 lph rate of flow for filter Each
4 Providing and fixing gun metal dial type pressure gauge (lOOmm dia) of
rating 0-10 kg./cm2 with gun metal isolating cock pig and connecting Each
oioe. 5 Supply, assembly, erection, testing and commissioning of chlorinator with
metering pump suitable for operation on 220 ± 5% single phase, 50 Hz AC
supply, compete in all respects.
a) Suitable for flow rate 12000 lph
J SUCTION AND DELIVERY PIPES AND VALVES FOR WATER SUPPLY
PUMPS
~~
Each
• l4o ~o ~ " f~ u I 3TilM ~ - 1. ,!ll1h •. . ~ .:.u"P' .i • ' . .., .
7 27331.00
100 115.00
50 135.00
1 208690.00
1 9357.00
1 8935.00
1 1214.00
1 30689.00
1
a) b) c) d) e) f)
2
a) b)
c) d)
e) f)
3 a) b)
4
a)
b)
5
a) b) c) d)
6 a)
b)
7
a) b)
8 a)
b)
Providing and fixing G.I. suction & del ivery headers/pipes for water
supply pumps (IS:1239 heavy class) with G.I. Fittings (bends, tees,
reducers, plugs, union, flange & blank flanges etc) and clamps and
jointing with teflon tape or hold t ite including chase cutting and making
laood the walls. floors etc. wherever required. 50 mm nominal bore Meter 65 mm nominal bore Meter 80 mm nominal bore Meter 100 mm nominal bore Meter 150 mm nominal bore Meter 200 mm nominal bore Meter
Painting for G.I. Pipes with two or more coats of synthetic enamel paint
of approved quality and shade over a coat of approved primer coat as
directed including surface preparation (Shade as per pipe colour code) 50 mm nominal bore Meter 65 mm nominal bore Meter 80 mm nominal bore Meter 100 mm nominal bore Meter 150 mm nominal bore Meter 200 mm nominal bore Meter
Providing and fixing lever operated gun metal ball valve with SS ball. SOmm dia Each 6Smm dia Each
Providing and fixing gunmetal horizontal non-return valve with screwed
ends tested to 20 kg/cm2. SOmm dia Each 6Smm dia Each
Providing and fixing cast iron wafer type Butterfly valve of the following size complete with bolts, nuts, washers and neoprene gaskets as per specifications. 80 mm nominal bore Each 100 mm nominal bore Each 150 mm nominal bore Each 200 mm nominal bore Each
Provid ing and fixing cast iron dual plate wafer type non return valves. 80 mm nominal bore Each 100 mm nominal bore Each
Providing and fixing suction strainer with M.S. flanged connection
lOOOmm long, fabricated from 16 gauge Brass sheet with 3mm slots. lOOmm nominal bore Each 200mm nominal bore Each
Providing and fixing Y-strainer 80mm nominal bore Each lSOmm nominal bore Each
,..
~1':tf- ~ ) 'f19;:4
~ - "Q. xi. f.'i. f.=t. i=;-, ' 3fT1Rf ~ - 1, 3frf,/J
\fCi ~ff) (!ti,) '-· Q. xl. (:). f\ l>. 3WM~~ - '· , i :m
(3C?)
45 617.00 55 779.00
95 953.00 30 1350.00 10 1984.00
10 2117.00
45 28.00 SS 33.00
95 42.00
30 47.00
10 52.00 10 57.00
4 2978.00 9 6061.00
4 2916.00 6 4832.00
12 2962.00 4 3785.00
2 5810.00
1 13510.00
8 4983.00
2 6210.00
2 10423.00
1 17252.00
4 4860.00
2 12890.00
wY
p
1
A
2
a)
3
a)
4
SEWAGE TREATMENT PLANT
Supply, erection, testing and commissioning of underground sewage
treatment plant based on attached growth FAB technology for the
following:
Daily Avg. Sewage : 100 m3/day PH :7.5-8.5 BODS : 350 mg/I
S. Solids : 250 mg/I COD : 450 mg/I
Coliform : lOb - 107 counts I 100 ml Effluent discharge standard after treatment: Conforming to requirement approved standards PH :7.5-8.5 BODS : Less than 6 mg/I S. solids : Less than 30mg/l COD : Less than 150 mg/I Outlet Coliform : < 1000 counts I 100 ml (at CCT outlet)
Sewage treatment plant shall include supply erection, testing & commissioning of the following items:
Manual Bar screen for 100m3/day at the inlet of receiving sump. Size 500 x 1000 Nos.
Sewage pumps: Centrifugal type, non clog self priming pumps complete
with suction and delivery valves and non return vafves,suction and
delivery headers of an approved make of capable of handling minimum 7
to lOmm solids size for un treated effluent with fan cooled induct ion
motor with class 'B' insulation, mounted on a common structural base
plate, suitable vibration eliminated pads of approved design for pump
foundation, motor to be suitable for 400/440 volts, 3 phase, 50 cycles AC lc:1 molv with rom to c:11it the rnrrec;nnndinP oumoc;,
Capacity 5m 3/ hr at 12m head (For sewage li fting from equilization tank) Nos.
Sludge pumps: Centrifugal type, non clog self priming pumps complete
with suction and delivery valves and non return valves,suction and
delivery headers of an approved make of capable of handling minimum 7
to lOmm so lids size for untreated effluent with fan cooled induction
motor with class 'B' insulat ion, mounted on a common structural base
plate, suitable vibrat ion eliminated pads of approved design for pump
foundation, motor to be suitable for 400/440 volts, 3 phase, 50 cycles AC 1c;11nnlv with rom to c:11it the rnrresnnndine oumn, .
Capacity Sm3/hr at 12m head (For transfer of sludge) Nos.
Air Blowers: Twin lobe positive displacement type, rotary air blowers of
suitable type with V-belt drive, belt guard, base plate, inlet filter-silencer,
flexible connectors, check valve, relief valve, pressure gauge and piping.
d ~~ I
I ~ ~~ Q.tJo xr. R., ~ 3lJ'1NI ~ - ' ~r
~. ~~. 31ftft~f u. 1t. x1. ~ - A: ~ .. 3"1M~ . .:wm .
2 11400.00
2 24700.00
2 24700.00
~~ '3'o R. ~. fft. ~. fB. 3f1TM ~ - 1. 3fTlffl
a)
s
6
7
8
a)
9
10
a)
11
12
a)
13
a)
Capacity- 130m3/hr@ 6000 MMWG 2 Nos (lw+ls) Nos.
Non-Clogging, freely moving PP media for MBBR reactors Cum.
Air Grids (1 set): The FAB tanks are equipped with non clog Air Grids for
100m3 /day sewage flow to supply sufficient air for the treatment process
and maintain adequate circulation velocity to prevent solids from
settliniz. No. of Diffusers : as required
Non submerged air piping : GI Submerged Air Piping: SS 304 Job
Media for tube settler as per design requirement Cum.
Filter Feed pumps: Centrifugal type, monoblock, self priming pumps with
bronze in impeller of an approved make and complete with with suction
and delivery valves and non return valves,suction and delivery headers
capable of handling clear water complete with fan cooled induction
motor with class B insulation, mounted on a common structural base
plate with lOOmm dia pressure gauge with gunmetal isolation cock and
suitable vibration elimination pads of approved design for pump
foundation. Motor to be suitable for 400/440 volts, 3 phase, SO cycle AC 1c;unnlv with rom to c:11it the rnrresoondinP. oumos
Capacity 12m3/ hr at 30m head. Nos.
Filter press feed screw pumps of capacity 1.0m3/hr at 40m head. Nos.
Treat ed water pumps: Centrifugal type, monoblock, self priming pumps
with bronze in impeller of an approved make and complete with suction
and delivery valves and non return valves,suction and delivery headers
capable of handling clear water complete with fan cooled induction
motor with class B insulation, mounted on a common structural base
plate with lOOmm dia pressure gauge with gunmetal isolation cock and
suitable vibration elimination pads of approved design for pump
foundation . Motor to be suitable for 400/440 volts, 3 phase, 50 cycle AC ;~unnlv with rnm tn c:11it the corresnnndine oumos
Capacity 12m3/hr at SOm head. Nos.
Filter Press for compression, management & disposal of sludge with 18
Nos plates of 18" x 18" size (Hydraulic operated) . No.
Supply, assembly, erection, testing and commissioning of metering pump
suitable for operation on 220 ± 5% single phase, SO Hz AC supply,
compete in all respects. Suitable for flow rate 9000 lph No.
Vertica l, MSRL, filter: Fabricated from IS:226/2062 plate 6mm thick for
shell and 8mm thi ck M.S. plate for dished ends complete with initial
charge of filter media, face piping and valves accessories, painting, testing
and commissioning complete.
Capacity 12m3/ hr aW.Okg/cm 2 () /'I Set -· ,_
' ............ $,_£ ~1_, ~
---<I I~!., ~ ,,-l 1•e l~ ~ ~J
~~W1~1 ffr. ( ) ~. ~- ~- ~- ~. : 3JT1Nf~ -1. 3Wf'( J
~~' l ~. Q. ~ . Gio f-J. ~o 3JT1TW ~ - 1. 3lPRT
- .,. ..,~ . ' -1. ~u .. ~~~ \ l , ~ . {l. f\. P-t. ~ -!<
~~ .. :/PHI
2 123500.00
8 18050.00
1 114000.00
3 16466.00
2 26600.00
2 39900.00
'
2 49400.00
1 185250.00
1 19000.00
1 r i-,.\ .j2J8500.00
~y~ 0 ~- f.i. rc...
14 Vert ical, MSRL, activated carbon filter: Fabricated from IS:226/2062
plate 6mm thick for shell and 8mm thick M.S. plate for dished ends
complete wi th initial charge of filter media, face piping and valves accessories, painting testing and commissioning complete.
a) Capacity 12m3/ hr at 3.0kg/cm2
15 Providing & Fixing Ozonator of 90 grm/hour capacity for lOOKLD STP
plant. The Ozonator should be complete in all respects inclusive of
recirculation pump, static mixer, ventury injector, flow control valves, re-
circulation line, dissolved ozone monitor I controller, wa ter chill ing
system, ozone mixing system of desired capacity. (Creative I Aquatech svstems makel
16 Pipe lines and valves: cPVC pipes (SDR 11 grade) complete with fittings e.g. tees, crosses, plugs, sockets, elbows, reducers, supports and clamps,
puddle flanges, etc., cutting chases including painting pipes and fittings with epoxv paint over a coat of primer.
17 Main control Panel : Floor mounted dust and vermin proof control panel suitable for 415 volts, 3 phase, 4 wire, 50 cont rol panel sui table for 415
vol ts, 3 phase, 4 wire, 50 Hz totally enclosed containing all necessary motor starters, circuit breakers, indicating lights, selector switches,
relays, terminal blocks, controls and isolators complete in all respects
including Electrical Cabling, Earthing from motor control panel to the
equipment. (All as specified) . The panel shall be designed for 100 amps inrnmjng f,:,,:,der
18 Pollution control board approval: Approval from pollution board at initial
and various stages of works including preparation of report/drawings as
per pollution board requirements and arrangements of raw sewage for
testing and commissioning. Contractor shall include the cost of all chemicals consumed during testing and commissioning and the cost of
such items of works, which are not explicity mentioned above, but are mandatory to have pollution board approval. (All official fees paid to nnllution rnntrol hnard will hP borne bv the client).
19 Supply, erection, testing and commissioning of Flow meter suitable for
9000 LPH flow rate. a) 65 mm dia.
20 Supply, erection, testing and commissioning of Energy meter before
electrical panel.
21 Opertaion & Maintenance contract of STP for a period of two years after
commissioning. All spares and replacement of any defective part shall be
included in the contract. Note : The tenderer shall take all precautions in STP to avoid corrosion
due to nascent oxygen from ozonizer.
Q STORM WATER DRAINAGE SYSTEM
'4• ~o ~. f.i. 1: ;, awJW~ - t.~··'
Set 1 247000.00
Set 1 408500.00
Lot 1 76000.00
Nos. 1 251750.00
Job 1 47500.00
No. 1 47500.00
. No. 1 4750.00'
Job 1 1140000.00
1
a) b) c) d)
2
a)
b) c) d)
3
a) b)
4
a)
5
a)
6 a)
Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes wi th
collars jointed with stiff mixture of cement mortar in the proportion of
1:2 (1 cement: 2 fine sand) including testing of joints etc. complete:
150mm dia RCC pipe Metre
250mm dia RCC pipe Metre 300mm dia RCC pipe Metre 450mm dia RCC pipe Metre
Providing and laying cement concrete 1:5:10 (1 cement: 5 fine sand: 10
gra.ded stone aggregate 40mm nominal size) all-round S.W. pipes
including bed concrete as per standard design.
150mm dla RCC pipe Metre 250mm dia RCC pipe Metre 300mm dia RCC pipe Metre 450mm dia RCC pipe Metre
Providing and laying cement concrete 1:5:10 (1 cement: 5 coarse sand:
10 graded stone aggregate 40mm nominal size) up to haunches of S. W
pipes including bed concrete as per standard design.
150mm dia RCC pipe Metre
300mm dia RCC pipe Metre
Const ructing brick masonry chamber for underground C.I. inspect ion
chamber and bends with bricks in cement mortar 1:4 (1 cement: 4 coarse
sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions,
total weight of cover with frame to be not less than 38 kg (weight of
cover 23 kg and weight of frame 15 kg), R.C.C. top slab with 1:2:4 mix (1
cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size),
foundat ion concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone
aggregate 40 mm nominal size), inside plastering 12 mm thick with
cement mortar 1:3 (1 cement : 3 coarse sand), finished smooth with a
floating coat of neat cement on walls and bed concrete etc. complete as nPr c;t ;inrl;irrl rlPc;ion •
Inside dimensions 45Sx610 mm and 45 cm deep for single pipe line :
With common burnt clay F.P.S. (non modular) bricks of class designation
7.5 Each
Constructing brick masonry road gully chamber 50x45x60cm with bricks
in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450mm
precast RCC horizontal grating with frame complete as per standard design. Wi th common burnt clay F.P.S. (non modular) bricks of class designation
7.5 Each
Extra for depth beyond 45 cm of brick masonry chamber: For 455x610 mm size
~ - Aft_ ~ ~ \Jq ( ) ~:Ollt1~11 fl1.) ~t(l. ~ ., -~·~
\i. o~ (I. I 'lo ~- ~ .
JmRT ~- 3fllR1
995.00 330.00
255.00 445.00 220.00 481.00 50.00 670.00
845.00 688.00 255.00 928.00
220.00 1336.00
50.00 3006.00
150.00 433.00 684.00
35.00 4457.00
94.00 3759.00
~~ t'5 • . J(. ~o ~ o ~• ~•
3lJlRJ ~ - 1. aJTlRT
7
a)
8
9
a)
10
a)
With common burnt clay F.P.S. (non modular) bricks of class designation Metre
7.5
Constructing brick masonry circular type manhole 0.91 m internal dia at
bottom and 0.56m dia at top in cement mortar 1:4 (1 cement :4 coarse
sand), in side cement plaster 12 mm thick with cement mortar 1:3 (1
cement : 3 coarse sand) finished with a floating coat of neat cement,
foundation concrete 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone
aggregate 40 mm nominal size), and making necessary channel in cement
concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20
mm nominal size) finished with a floating coat of neat cement, all lrnmolete ::l<: ni:>r standard rii:><:il?n ·
0.91 m deep with S.F.R.C. cover and frame (heavy duty, HD-20 grade designation) 560 mm internal diameter conforming to 1.5. 12592, total
weight of cover and frame to be not less than 182 kg., fixed in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20
mm nominal size) including centering, shuttering all complete .
(Excavation, foot rests and 12mm thick cement plaster at the external
surface shall be oaid for seoaratelvl : With common burnt clay F.P.S. (non modular) bricks of class designation
Each 7.5
Extra depth for circu lar type manhole 0.9lm internal dia (at bottom)
beyond 0.91 m to 1.67 m
With common burnt clay F.P.S. (non modular) bricks of class designation Metre
7.5
Constructing brick masonry circular manhole 1.22m internal dia at
bottom and 0.56m dia at top in cement mortar 1:4 (1 cement :4 coarse sand) inside cement plaster 12mm thick with cement mortar 1:3 (1
cement :3 coarse sand) finished with a floating coat of neat cement foundation concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone
aggregate 40mm nominal size) and making necessary channel in cement
concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate
20mm nominal size) finished with a floating coat of neat cement, all lcomolete as oer st;:inrl~rd rli:>si,m · 1.68 m deep with SFRC Cover and frame (heavy duty HD-20 grade
designation) 560mm internal diameter conforming to I.S. 12592, total
weight of cover and frame to be not less than 182kg. fixed in cement
concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate
20mm nominal size) including centering, shuttering all complete .
(Excavation, foot rests and 12 mm thick cement plaster at the external
surface shall be oaid for seoaratelvl : With common burnt clay F.P.S. (non modular) bricks of class designation
Each 7.5
Extra depth for circular type manhole l.22m internal dia (at bottom) beyond 1.68 m to 2.29 m : With common burnt clay F.P.S. (non modular) bricks of class designa tion
Metre 7.5
~
~ c,) /
I) ~~ ~ ~• ~. xfo ~• f.lQ f': .
~~-l. ~R/
~ . ~o xlo ~ o f-\ ' · ,. 3WTW ~cfiT~ - 1. ~·: d
·.qf'l. ~ . -,,1 a~, H. o~ n -"'; A. f."1. --~~. P n J
7.00 3728.00
15.00 8301.00
10.00 4600.00
4.00 15644.00
5.00 J57.00 \..
W~ \J. IL ~o fft. ~. ~ 3'1'm~ - 1. 3fflf" I
11
12
a)
13
14
•
a)
15
a)
Providing orange colour safety foot rest of minimum 6 mm thick plastic
encapsulated as per IS : 10910 on 12mm dia steel bar conforming to IS : 1786 having minimum cross section as 23 mmx25mm and over all
minimum length 263 mm and width as 165mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by
ribbing or chequering besides necessary and adequate anchoring
projections on tail length on 138 mm as per standard drawing and
suitable to with stand the bend test and chemical resistance test as per specificat ions and having manuf acture's permanent identification mark
to be visible even after fixing, including fixing in manholes with 30x20x15
cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded <: t nn,:, -,nar,:,a::, t ,:, JO mm nnmin::il <:iH>\ rnmnlot,:, ::i<: n,:,r rl,:,cian
Earth work in excavation by mechanical means (hydraullic excavator) I manual means over areas (exceeding 30cm in depth. l.5m in width as
well as 10 sqm on plan) including disposal of excavated earth lead upto
50m and lift upto l.5m, disposal earth to be levelled and neatly dressed.
All kinds of soil
Filling available excavated earth (excluding rock) in treanches, plinth,
sides of foundations etc. in layers not exceeding 20cm in depth,
consolidating each deposited layer by ramming and watering, lead up to
50m and lift upt l.Sm.
Excavating trenches of required width for pipes, cables, etc including
excavation for sockets, and dressing of sides, ramming of bottoms, depth
upto 1.5 m including getting out the excavated soil, and then returning
the soil as required, in layers not exceeding 20 cm in depth, including
consolidating each deposited layer by ramming, watering, etc. and
disposing of surplus excavated soi l as directed, within a lead of 50 m :
All kind of soils
Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia.
Pipes, cables etc. exceeding 300 mm dia. but not exceeding 600 mm dia.
Extra for excavating trenches for pipes, cables etc. in all kinds of soil for
depth exceeding 1.5 m, but not exceeding 3 m. (Rate is over corresponding basic item for depth upto 1.5 metre).
Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia.
~ - (fil.) .. u. ~-~. ~ Q ft; ~ ~ -1.3ffTRI
(ftf .) ~. J:1. x'T. ~ . f·l, 1~1. ~ ~ - ,. ,,mt.ff
Each 74.00 296.00
Cum 89.00 147.00
Cum 11.00 106.00
Metre 1520.00 197.00'
Metre 50.00 308.00
Metre 130.00 267.00