Boysen Paints

7/25/2019 Boysen Paints

1/15

BOYSEN PAINTS

TYPE DESCRIPTION PRINCIPAL USES PRACTICAL COVERAGE SURFACE DRY DRY THROUGH DRY FILM THICKNESS OVERCOATING INTERVAL THINNING APPLICATION

BOYSEN Clear Acrylic

Emulsion #700

Acrylic type transparent coating that acts as a

barrier against dampness on concrete walls.

Improves performance of latex paint

applied on humid and/or damp

environments.

20-25 square meter / 4 l iters / coat Thi rty (30) minutes Two (2) hours 1-1.5 mi ls /coat Al lowone hour before recoating.

Use as supplied. If

necessary, thin with not

more than 1/2 liter of water

per 4-liter can

paint brush, roller or airless

spray.

NewMasonry:

PREMIUM ACRYLIC WATER BASED PAINTS

: , ,

Allownewmasonry to dry 14 to 28 days under normal weather conditions before painting. Surfaces to be painted should be clean and dry, free fromoil, grease, dust, dirt contaminants, and all loose grit and mortar. Treat newmasonry with a solution of 1 part BOYSEN Masonry Neutralizer #44 diluted in 16 parts wroller. Let dry overnight before rinsing with water to remove white crystals that formon the surface. Let dry before painting.

SURFACE PREPARATION

PAINTING SCHEDULE

1st Coat: BOYSENPermacoatFlat Latex #701

2nd Coat: BOYSENClear Gloss Acrylic Emulsion #700

DESCRIPTION PRINCIPAL USES PRACTICAL COVERAGE SURFACE DRY DRY THROUGH DRY FILM THICKNESS OVERCOATING INTERVAL THINNING APPLICATION

BOYSEN Masonry Putty

#7311

Water based product especially prepared for

filling minor surface unevenness while using

latex paint systems. Can also be used for full

puttying.

For interior concrete, stucco, bricks

plaster or any surface minor imperfection.

Full Putty - 10-12 square meter / 4 liters /

coat

Spot putty - 25 square meter / 4 liters /

coat

Thirty (30) minutes Two (2) hours Allow two hours before recoating Use as supplied. putty knife


Putty: BOYSENMasonry Putty #7311

Topcoat: BOYSENPermacoatLatex (flat, semi-gloss, gloss)

Note: Interior use only. For exterior, use BOYSEN AcrytexCast #1711


BOYSEN Permacoat Latex

A100%acrylic latex paint with excellent hiding,

durability and dirt pick-up resistance. It finishes

painting jobs in less coats, yet lasts longer than

other brands allowing you to save a lot on time,

effort, worry and money.

For interior and exterior such as concrete,

stucco, bricks plaster, hollowblocks,

drywall surfaces, and properly primed

wood.

25-30 square meter / 4 l iters / coat Thi rty (30) minutes Two (2) hours 1-1.5 mi ls/coat Al lowone hour before recoating.

Use as supplied. If


more than liter of water

per 4-liter can

paint brush, roller or airless

spray.


PAINTING SCHEDULE

Topcoat: BOYSENPermacoatLatex (flat, semi-gloss, gloss)

PAINTING SCHEDULE

:

:

Putty:

BOYSEN Masonry Putty #7311 (interior use)

BOYSENAcrytex Cast#1711 (exterior use)

2nd &3rd Coat: BOYSENPermacoat Flat Latex (any desired color)

#3101 DESCRIPTION PRINCIPAL USES PRACTICAL COVERAGE SURFACE DRY DRY THROUGH DRY FILM THICKNESS OVERCOATING INTERVAL THINNING APPLICATION


2/15

BOYSENPermatex #3101

Awater-based, full-bodied paint that dries to a

fine rubbery coating, creating a beautiful

textured finish on interior walls and ceilings

bringing elegance to your home interior. It

adheres easily on wood, masonry, and drywall

surfaces. Conceals hairline cracks and minor

surface imperfections, and dries to a fine

rubbery coating that does not become brittle,

leaving virtually no roomfor cracking, chipping,

or peeling off.

For interior wood, drywall, and masonry

surfaces.5 - 6 square meter / 4 liters Two (2) hours Overnight Two (2) hours

Use as supplied. If


more than 1/2 liter of water

per 4 liter can

For a regular texture

pattern, apply

BOYSENPermatex

#3101 straight from the ca

using a regular textured

roller. If a different design

desired, first apply

BOYSENPermatex

#3101 with a regular

textured roller immediately

followed by the desired

Wood: Masonry & Drywall:

1st Coat: BOYSENFlatwall Enamel #800 1st Coat: BOYSENPermacoatFlat Latex #701

Putty: BOYSENPlasolux Glazing Putty #311 Putty: BOYSENMasonry Putty #7311

Texture: BOYSENPermatex#3101 Texture: BOYSENPermatex#3101

2nd &3rd coat: BOYSENPermacoatLatex (any desired color) 2nd &3rd coat: BOYSENPermacoatLatex (any desired color)

I I I I I I I I I I I I I

PAINTING SCHEDULE


BOYSEN Roofgard

a gloss acrylic, water-based roof paint designed

to protect and adhere to most roof substrates. It

gives a durable and flexible film, fast-drying time

and good gloss retention.

For galvanized iron surfaces, pre-painted

galvanized sheets, asphalt shingles, and

unglazed roof ti les. 25-30 square meter / 4 l iters / coat Thirty (30) minutes Two (2) hours 1.5 mils/coat Two (2) hours

Maximum1/2 liter water per

4 liters paint

by brush, roller or spray.

Clean equipment with soap

and water after use

For unpainted galvanized iron sheets, etch the surface by applying 10%BOYSENMetal Etching Solution #71 (dilute 1 part of B-71 to 9 parts water). Wipe the surface with rag soaked in BOYSEN Paint Thinner #0340 to remove grease. Rinse with water and let dry.

For prepainted galvanized iron sheets, scuff sand surface using sandpaper and wipe the surface with clean rag before applying paint. Spot prime if necessary.

For corroded G.I. surface, remove rust by wire brushing and use BOYSEN Metal Etching Solution #71. Let it stay for 10-15 minutes. Be sure to wash off surface thoroughly with water or paint thinner and let dry. Apply primer a few hours after application of B-71 and before rust sets in.

For newunglazed roofti les, make sure surfaces are completely clean and dry.

Primer for: Topcoat:

Galvanized Iron Sheets BOYSENRoofgard (2-3 coats; any desired color)

BOYSENRed Oxide #310, BOYSENRust OffPrimer Gray #330, Repainting:

or BOYSENPrimeguard#4310 For G.I. sheets with paint in good condition, clean surface of dirt and dust by washing and apply two coats of BOYSEN Roofgard.

Unglazed tiles:

BOYSENAcrytexPrimer #1705


SPECIALTY WATER BASED COATINGS

SURFACE PREPARATION

PAINTING SCHEDULE


BOYSEN EcoPRIMER

#105

An eco-friendly acrylic water-based primer used

for masonry and drywall surfaces. This ultra-low

volatile organic compound (VOC) formulation is

designed to have superior alkali resistance,

excellent adhesion and sealing properties ideal

for interior and exterior application.

25-30 square meter / 4 l iters / coat. Thirty (30) minutes. Two (2) hours. 1-1.5 mils/coat. Allowone hour before recoating. Use as supplied.paint brush,roller orairle

spray.

NewMasonry:

SURFACE PREPARATION


3/15

Repainting:

1st Coat: BOYSENEcoPRIMER#105

Putty: BOYSENAcrytexCast #1711 (for exterior);

BOYSENMasonry Putty #7311 (for interior)

2nd &3rd Coat: BOYSENHealthy Home(for interi or)

VirtuosoSilk Touch(for interior)

BOYSENKNOxOUTAir Cleaning Paint #8701 Acrylic Water-based

BOYSENKNOxOUTAir Cleaning Paint #8702 Silicon-based


Odor-less, lowVOC, remiumacr lic, water-

. ,

.

Is the ideal choice for residences,

, ,

, ,

.

.

. . . ,

Allownewmasonry to dry for 14 to 28 days under normal weather conditions before painting. Surface to be painted should be clean and dry, free fromoil, grease, dust, dirt, contaminants, and all loose grit and mortar. Treat newmasonry with a solution of 1 part BOYSEN Masonry Neutralizer #44 diluted in 16 parts

roller. Let dry overnight before rinsing with water to remove white crystals that form on the surface. Let dry before painting.

Remove all loose, scaling, flaking and peeling off paint using BOYSENPaint and Varnish Remover #141, wire brushing, scraping, or water blasting. Let it dry. Sand smooth painted surfaces for improved adhesion. Apply 1 coat of BOYSEN Chalk Blockerfor chalking old paint. In case of mildewi nfestation, treat w

bleach solution (1:3, laundry bleach to water, respectively) by swabbing or brushing. To ensure proper treatment, allow to stand on surface for overnight before washing off residue. Let dry.

PAINTING SCHEDULE

I

BOYSEN Healthy Home

Odor-less Antibacterial Latex

Paint

- , , , -

based interior coating with exclusive Microban

antibacterial protection to give extra defense

against bacteria such as E. coli and Salmonella,

as well as mildewand fungus.

I ,

medical facilities, nursing homes,

schools, day care facilities, and food

commissaries. For inter ior concrete and

drywall surfaces.

25-30 square meter / 4 l iters / coat Thirty (30) minutes Two (2) hours 1-1.5 mils/coat Allowone hour before recoating. Use as supplied.paint brush, roller or airless

spray

NewMasonry:

Repainting:

Concrete Drywall Surfaces

1st Coat: BOYSENPermacoatFlat Latex #701 1st Coat: BOYSENPermacoatFl at Latex #701

Putty: BOYSENMasonry Putty #7311 Putty: BOYSEN GypsumJoint Compound #711

2nd & 3rd Coat: BOYSENHealthy Home 2nd &3rd Coat: BOYSENHealthy Home


Is a 100%acrylic water-based paint that is low

odor, lowVOC, lead free, and has outstanding

. I

.

,

,

.

.

.

. . . ,

.

Allownewmasonry to dry 14 to 28 days under normal weather conditions before painting. Surfaces to be painted should be clean and dry, free fromoil, grease, dust, dirt contaminants, and all loose grit and mortar. Treat newmasonry with a solution of 1 part BOYSEN Masonry Neutralizer #44 diluted in 16 parts w

roller. Let dry overnight before rinsing with water to remove white crystals that formon the surface. Let dry before painting.

Remove all loose, scaling, flaking and peeling off paint using BOYSENPaint and Varnish Remover #141, wire brushing, scraping, or water blast ing. Let dry. For chalking old paint, use BOYSEN Chalk Blocker #7304 as primer. In case of mildew infestation, treat with fungicidal wash solution or bleach solution (1:3

respectively) by swabbing or brushing. To ensure proper treatment, allow to stand on surface for overnight before washing off residue. Let dry.

PAINTING SCHEDULE

I

SURFACE PREPARATION

Virtuoso Silk Touch

I

, , ,

color retention. It dries to a luxurious silk finish

that not only imparts a sense of warmth and

depth to your living space but is also distinctively

smooth to touch. With Teflonsurface

protector, oil and dirt cannot easily stick to your

walls, making it easy to wipe off common

everyday stains.

Best for areas in need of stain resistant

walls. For interior concrete and drywall

substrates.

25-30 square meter / 4 l iters / coat Thirty (30) minutes Two (2) hours 1-1.5 mils/coat Allowone hour before recoating. Use as supplied.paint brush, roller or airless

spray.

Please refer to CHOOSEYOUR PAINTsection for specifics.

SURFACE PREPARATION

PAINTING SCHEDULE


4/15

Concrete Drywall Surfaces

1st Coat: BOYSEN PermacoatFlat Latex #701 1st Coat: BOYSENPermacoatFlat Latex #701

Putty: BOYSENMasonry Putty #7311 Putty: BOYSENGypsumJoint Compound #711

2nd & 3rd Coat: VirtuosoSilk Touch 2nd & 3rd Coat: VirtuosoSilk Touch


BOYSEN Alkyd Traffic Paint

An alkyd-based paint for traffic markings/linings.

It must be applied on epoxy-primed asphalt and

rough concrete.

It is designed for use on street markings,

curbs, traffic lanes and safety zone lining.20-25 sq. m/ gal / coat 30 minutes 1 hour 1 hour 1 hour

BOYSENPaint Thinner

#0340 if neededBy brush, roller

1st coat: BOYSENEpoxy Primer White #2200

2nd and 3rd coat: BOYSENAlkyd Traffic Paint


. I

. I

.

. .

ALKYD ENAMEL / OIL BASED PAINTS

PAINTING SCHEDULE

I

BOYSEN Flatwall Enamel

#800

a a y ype pain a provi es grea

durability while being noted as a fast drying

paint. It is formulated to give a tough and

durable film. It is also used as a primer for

enamel coatings.

For interior and exterior wood surfaces. 20 - 25 square meter / 4 li ters / coat Thirty (30) minutes Eight (8) hours 1.5 mils/coat Allowsix (6) hours before recoatUse BOYSENPaint

Thinner #0340By brush or roller

Surface to be painted should be clean and dry, free fromdust, dirt and other foreign matter. Hammer all nails deep enough to apply putty. Sand rough wood until smooth, then dust off before paint ing.

If repainting, first remove all blistering, peeling and scaling paint by wire brushing or BOYSEN Paint and Varnish Remover #141. Clean surfaces thoroughly before painting.

1st Coat: BOYSENFlatwall Enamel #800

Putty: BOYSENPlasolux Glazing Putty #311

2nd &3rd Coat: BOYSENFlatwall Enamel #800


BOYSEN Heat Resistin g

Alumin um #95

Formulated for surfaces subject to heat with

peak temperature of 800 F or 427 C.

For metal surfaces of equipment,

radiators and machinery.20 square meter / 4 liters / coat

Will dry when peak

temperature is reached.1.5-2 mils Allow overnight before recoating not necessary by brush

Metal:

Wipe the surface with rag soaked in lacquer thinner to remove dust, dirt, grease, oil, wax and other foreign matter.

For rusted portions, wire brush or scrape loose rust and apply BOYSEN Metal Etching Solution #71. Let it stay for 10-15 minutes. Be sure to wash off surface thoroughly with water or paint thinner, letting it dry before applying paint. Product should be applied immediately after treatment to prevent flash rusting.

I I

SURFACE PREPARATION

PAINTING SCHEDULE

SURFACE PREPARATION

Apply 2 to 3 coats of BOYSENHeat Resisting Aluminum#95 on bare substrate.


BOYSEN Plasolux Glazing

Putty #311

An alkyd-type product specially prepared for

filling minor surface unevenness on enamel-

painted wood.

For filling minor surface dents and

imperfections on wood.

Full Putty - 10-12 square meter / 4 liters /

coat

Spot putty - 25 square meter / 4 liters /

coat

4-5 hours Overnight Allowtwo hours before recoatingBOYSENPaint Thinner

#0340 if necessaryput ty knife

1st Coat: BOYSENFlatwall Enamel White #800

, . . , . .

PAINTING SCHEDULE

PAINTING SCHEDULE


5/15

Putty: BOYSENPlasolux Glazing Putty #311

2nd &3rd coat: BOYSENQuick Drying Enamel (any desired color),

BOYSENSemi-Gloss Enamel #200, or BOYSENFlatwall Enamel White #800


BOYSEN Quick Drying

Enamel

An alkyd type paint that provides great durability

while being noted as a fast drying paint. It is

formulated to give a tough, durable, beautiful

and high build film on wood and metal. Its

superior hiding, combined with an exceptionally

high gloss level, leads to an excellent, long-

lasting finished appearance.

Superior for exterior and interior wood

and metal surfaces.20 - 25 square meter /4 li ters /coat Five (5) hours maximum Two (2) hours 1.5 mi ls/coat Al loweight (8) hours

Use BOYSENPaint

Thinner #0340 if necessaryBy brush or roller

Wood - Surface to be painted should be clean and dry, free fromdust, dirt and other foreign matter. Hammer all nails deep enough to apply putty. Sand rough wood until smooth, then dust off before painting.

If repainting, first remove all blistering, peeling and scaling paint by wire brushing or BOYSEN Paint and Varnish Remover #141. Clean thoroughly prior to painting.

Metal - Wipe the surface with rag soaked in paint thinner to remove dust, dirt , grease, oil, wax and other foreign matter. For newG.I. sheets, etch the surface by applying 10%BOYSEN Metal Etching Solution #71 (dilute 1 part of B-71 to 9 parts water).

SURFACE PREPARATION

, , , , . .I. , .

If repainting, wire brush or scrape rusted metals and apply BOYSEN Metal Etching Solution #71 to remove all rust. Let it stay for 10-15 minutes. Be sure to wash off surface thoroughly with water, lett ing it dry before applying paint. Prime immediately after drying.

WOOD METAL

1st Coat: BOYSEN Flatwall Enamel #800 1st coat: BOYSENRed Oxide Primer #310,

Putty: BOYSEN Plasolux Glazing Putty #311 BOYSEN Rust OffPrimer Gray #330, or BOYSENPrimeguard#4310

2nd &3rd Coat: BOYSENQuick Dry Enamel (any desi red color) 2nd &3rd Coat: BOYSEN Quick Dry Enamel (any desired color)


BOYSENRed Oxide Primer#310

Arust inhibiting primer for steel and iron

surfaces. It is particularly good for metal shops

who deliver metal products coated with a shop

primer to protect themfromrust corrosion until

such time as they are finished with desiredtopcoat.

As a primer for exterior and interior steel. 25 - 30 square meter /4 liters /coat Two hours 1.5 mils/coat 8 hours to overnightUse BOYSENPaint

Thinner #0340 if necessary

By brush, roller or

conventional spray

Wipe the metal surface with rag soaked in paint thinner to remove dust, dirt, grease, oil, wax and other foreign matter. For new G.I. sheets, etch the surface by applying 10%BOYSEN Metal Etching Solution #71 (dilute 1 part of B-71 to 9 parts water).

If repainting, wire brush or scrape rusted metals and apply BOYSENMetal Etching Solution #71 to remove all rust. Let it stay for 10-15 minutes. Be sure to wash off surface thoroughly with water, letting it dry before applying paint. Prime immediately after drying.

1st Coat: BOYSENMetal Primer Red Oxide #310

2nd &3rd Coat: BOYSENQuick Dry Enamel (any desired color)


SURFACE PREPARATION

PAINTING SCHEDULE

PAINTING SCHEDULE


BOYSEN Reflectorized

Traffic Paint

An alkyd-type paint specially developed to resist

the rigorous environment encountered on

highways, roads, pavements, and parking lots. It

forms a durable filmthat offers good wear

resistance and better reflective beads retention

for safety markings.

Areflectorized variant to the alkyd-based

traffic paint for use on road markings and

pavement linings. To be used only on

areas in direct contact to wheel traffic

otherwise the reflectorized-effect will not

manifest.

20 square meter / 4 liters / coat 10 minutes 30 minutes 30 minutesBOYSENPaint Thinner

#0340 if necessaryBy brush

1st coat: BOYSEN

Epoxy Primer White #22002nd coat &3rd coat: BOYSENReflectorized Traffic Paint (of desired color)

PAINTING SCHEDULE


6/15


BOYSEN Schoolboard

Slating Paint, Green #655

An alkyd based paint that dries to a flat finish for

classroomblackboards, bulletin boards and

similar flat surfaces intended for chalk markings.

For metal or wood surfaces. 25-30 square meter / 4-liter / coat 2-4 hours Overnight 1.5 mils/coat Allow overnight before recoatingBOYSENPaint Thinner

#0340by brush or roller

Newwood:

Surface to be painted should be clean and dry, free fromdust, dirt and other foreign matter. Hammer all nails deep enough to apply putty. Sand rough wood until smooth, them dust off before painting.

Repainting:

For previously painted surfaces, scrape off loosely adhering paint. Remove oil and grease by detergent cleaning. Scuff sand for improved anchorage of succeeding coats.

1st Coat: BOYSENFlatwall Enamel #800

Putty: BOYSEN Plasolux Glazing Putty #311

Topcoat: BOYSENSchoolboard Slating Paint #655


SURFACE PREPARATION

PAINTING SCHEDULE


BOYSEN Semi-Gloss

Enamel #200

An alkyd type paint that provides great durability

while being noted as a fast drying paint. It is

formulated to give a tough and durable filmon

wood and metal. Its superior hiding and sheen

makes it easier to clean and resist wear and

abrasion.

For interior and exterior wood and metal

surfaces.20 - 25 square meter / 4 li ters / coat Thi rty (30) minutes Ten (10) hours 1.5 mi ls/coat Al lowsix (6) hours before recoat

Use BOYSENPaint

Thinner #0340 if necessaryBy brush or roller

Wood - Surface to be painted should be clean and dry, free fromdust, dirt and other foreign matter. Hammer all nails deep enough to apply putty. Sand rough wood until smooth, then dust off before painting.

If repainting, first remove all blistering, peeling and scaling paint by wire brushing or BOYSEN Paint and Varnish Remover #141. Clean thoroughly prior to painting.

Metal - Wipe the surface with rag soaked in paint thinner to remove dust, dirt , grease, oil, wax and other foreign matter. For newG.I. sheets, etch the surface by applying 10%BOYSEN Metal Etching Solution #71 (dilute 1 part of B-71 to 9 parts water).

If repainting, wire brush or scrape rusted metals and apply BOYSENMetal Etching Solution #71 to remove all rust. Let it stay for 10-15 minutes. Be sure to wash off surface thoroughly with water, letting it dry before applying paint. Primer should be applied immediately after treatment.

Wood Metal

1st coat: BOYSENFlatwall Enamel #800 1st coat: BOYSENRed Oxide Primer #310,

Putty: BOYSENPlasolux Glazing Putty #311 BOYSENRust OffPri mer Gray #330, or BOYSENPrimeguard#4310

2nd &3rd coat: BOYSENSemi-Gloss Enamel #200 2nd &3rd coat: BOYSENSemi-Gloss Enamel #200


BOYSEN Silver Finish

Alumin um Paint #75

Aready mixed aluminumpaint for general use

on industrial and decorative work, for maximum

wear.

For exterior and interior metal. 25-30 sq.m / gallon 2 -4 hours Overnight 1.5 mils/coat Allow overnight before recoating not necessary by brush

SURFACE PREPARATION

PAINTING SCHEDULE

I I

1st coat: BOYSENRed Oxide Primer #310, BOYSENRust OffPrimer Gray #330, or BOYSENPrimeguard#4310

2nd &3rd Coat: BOYSENSilver Finish AluminumPaint #75


BOYSENSpar Varnis h #58

Aclear, alkyd-type, glossy varnish that dries to a

hard durable film without obliterating the natural

appearance of wood.

Enhances wood grain of furniture,

fixtures, cabinets, doors, doorjambs and

panels.

25-30 sq.m/ gallon 4-6 hours 12 hours 1.5 mils/coat Recoat after 12 hoursBOYSENPaint Thinner

#0340by brush or spray

Newwood surfaces:

I I

PAINTING SCHEDULE


7/15

Stain: BOYSENOil Wood Stain (optional)

Final coat: BOYSENSpar Varnish #58. Recoat for a clear gloss finish.

Repainting:

Loose film should be stripped. BOYSENPaint and Varnish Remover #141 can be used to totally remove the existing finish.

If old lacquer finish is in good condition, sand surface. Make sure to clean and dry before coating with BOYSEN Spar Varnish #58.


BOYSEN Oil Wood Stain

Available in various shades to bring out a clear

and natural tone in wood. When clear coatedwith BOYSENLacquer varnish products,

BOYSENOil Wood Stain highlights wood

grains, adds freshness and color, and provides

superior protection.

For enhancing wood grain on interior

wood works and other surfaces such as

cabinets, furniture, paneling, etc.

25 - 30 square meter /4 liters /coat

(depending on wood absorptivity)Two (2) hours 4-5 hours 1.5 mils / coat Overnight

BOYSENPaint Thinner


OIL WOOD STAINS

SURFACE PREPARATION

Sand surface until wood is smooth to the touch and no slivers or rough edges remain. Hammer all nails deep enough to apply putty. Dust off surfaces completely then wipe with a clean rag.

If repainting, remove all paint by wire brushing, scraping, or by using BOYSEN Paint &Varnish Remover #141.

NewWood:

1st coat: BOYSENOil Wood Stain (any desired color)

2nd coat and 3rd coats: BOYSENLacquer Sanding Sealer #1254

4th and 5th coats: BOYSENClear Gloss Lacquer #1250


BOYSENXyladecor

Asolvent based, deep penetrating type of stainthat combines decorative, water repellent and

wood preserving properties in one and dries to a

silk matte finish. It emphasizes the grain,

bringing out the natural beauty in any kind of

wood.

Is the wood stain available that could beused for exterior and interior wood

surfaces. It is the best way to protect

your wood since it seals, prevents fungal

growth, mold and insect attacks through

its preservative contents.

20 - 25 square meter /4 liters /coat (may

vary depending on wood absorptivity)Thirty (30) minutes Overnight

30 minutes, depending on weather

and absorption rateNot necessary

by brush, spray or by

dipping

Sand surface until wood is smooth to the touch and no slivers or rough edges remain. Hammer all nails deep enough to apply putty. Dust off surfaces completely then wipe with a clean rag.

If repainting, remove all paint by wire brushing, scraping, or by using BOYSEN Paint &Varnish Remover #141.

I

PAINTING SCHEDULE

Thoroughly stir the can contents before using. Apply BOYSEN Oil Wood Stain direct to bare wood without primers or undercoats either by brush, spray or by dipping in an open trough or tank. Lightly brush or wipe over once along the grain to remove excess material and to smooth out any runs. Leave each coat for

totally dry. Recoat for a darker shade.

SURFACE PREPARATION

PAINTING SCHEDULE

Thoroughly shake the can before opening. Apply BOYSENXyladecordirect to base wood without primers or undercoats either by brush, spray or by dipping in an open trough or tank to achieve total covering rate. Shake and stir Xyladecor often during use.

By Spray: Use a coarse nozzle (about 1-5 mm) giving a steamof material rather than a fine atomizing type paint spray. Working pressure should be approximately 44 lbs. / m2. Spraying is not recommended for planed surfaces.

By dipping: Dip the timber in BOYSENXyladecorfor 2 minutes, varying the time required according to the absorbency of the wood. Stand the timber on end and allowto drain. If necessary, li ghtly brush the surface once in the direction of the grain before it dries.

Note: If a very even color finish is desired on wood with varying degrees of absorbency, apply BOYSEN XyladecorColorless fi rst before applying colored varieties of Xyladecor. BOYSENXyladecorColorless is not recommended for exterior use on its own.

NITROCELLULOSE LACQUER BASED COATINGS

By Brush: Apply at least 3 full brush coats, laying the paint into the wood rather than brushing out. Leave each coat for about thirty (30) minutes, depending on the weather and the absorption rate. Lightly brush or wipe over once along the grain to remove excess material and to smooth out any runs.

I I


8/15


BOYSEN Automotive

Lacquer #1300

Anitrocellulose, solvent-based, high gloss,

lacquer type paint that is easy to apply and dries

rapidly to a long-wearing attractive finish.

For indoor wood surfaces such as doors,

doorjambs, cabinets, and shelves.25-30 square meter / 4 liters / coat 10 minutes 30 minutes 1.5 mils / coat 1 hour

BOYSENLacquer Thinner

#50by spray or brush


Newwood surfaces:

1st coat: BOYSENLacquer Primer Surfacer #305

Putty: BOYSENLacquer Spot Putty #306 if required

2nd coat: BOYSEN

Lacquer Primer Surfacer #305 on puttied areas

Final coat: BOYSENAutomotive Lacquer #1300 in required number of coats

(Note: 10%by volume of BOYSENLacquer Flo is mixed with the topcoat just before application to prevent moisture blushing)


SURFACE PREPARATION

PAINTING SCHEDULE


BOYSENClear Dead Flat

Lacquer #1253

Is a nitrocellulose, solvent-based, flat lacquer

varnish finish that dries to a hard durable film. Its

high build properties make it superior for

furniture, fixtures, and other woodworks.

For interior sealed wood such as

furniture, store fixtures, cabinets, doors

and panels.

25-30 square meter / 4 liters / coat 10 minutes 1 hour 1.5 mils / coat Recoat after 30 minutesBOYSENLacquer Thinner

#50by spray or brush

Newwood surfaces: Repainting:

Sealer coat: BOYSENLacquer Sanding Sealer #1254 Old finish in bad condition should be stripped. BOYSENPaint and Varnish Remover #141 can be used to totally remove the finish.

Final coat: BOYSENClear Dead Flat Lacquer #1253 If old lacquer finish is in good condition, sand surface. Make sure to clean and dry before coating the required coats of BOYSEN Clear Dead Flat Lacq

(Note: 10%by volume of BOYSENLacquer Flo is added to the varnish mixture just before application to prevent moisture blushing)


BOYSEN Clear Gloss

Lacquer #1250

Anitrocellulose, solvent-based, high gloss

lacquer varnish finish that dries to a hard durable

film.


furnitures, fixtures, cabinets, doors and

panels.




Stain (optional): Boysen Oil Wood Stain Old finish in bad condition should be stripped. BOYSENPaint and Varnish Remover #141 can be used to totally remove the finish.

Sealer Coat: BOYSENLacquer Sanding Sealer #1254, sanded lightly before topcoat application If old lacquer finish is in good condition, sand surface. Make sure to clean and dry before coating BOYSEN Clear Gloss Lacquer #1250.

:

PAINTING SCHEDULE

PAINTING SCHEDULE

Final coat: BOYSENClear Gloss Lacquer #1250



BOYSEN Lacquer Primer

Surfacer #305

Anitrocellulose lacquer type sealer with

excellent holdout properties that provide

good foundation for the desired lacquer topcoat.

As primer for indoor wood surfaces 25-30 square meter / 4 liters / coat Ten minutes Thirty minutes 1.5 mils/coatAllowthirty minutes before

recoating

BOYSENLacquer Thinner



PAINTING SCHEDULE


9/15

1st coat: BOYSENLacquer Primer Surfacer #305 Old finish in bad condition should be stripped. BOYSENPaint and Varnish Remover #141 can be used to totally remove the finish. Follow procedure o

2nd coat: BOYSENLacquer Spot Putty #306 If old lacquer finish is in good condition, sand surface.

3rd coat: BOYSENLacquer Primer Surfacer #305

Final coat: BOYSENAutomotive Lacquer #1300 or BOYSENGloss Lacquer Enamel #1200 in required coats


BOYSEN Lacquer Sanding

Sealer #1254

Acommercial grade nitrocellulose-based sealer

for wood before finishing with either gloss or flat

lacquer. It has good sealing and hold out

properties, and require less sanding.


furniture, fixtures, cabinets, doors and

panels.




Sealer coat: BOYSENLacquer Sanding Sealer #1254 Old finish in bad condition should be stripped. BOYSENPaint and Varnish Remover #141 can be used to totally remove the finish.

Final coat: BOYSENClear Gloss Lacquer #1250 or BOYSENClear Dead Flat Lacquer #1253 If old lacquer finish is in good condition, sand surface. Make sure to clean and dry before coating.


PAINTING SCHEDULE


BOYSEN Lacquer Spot

Putty #306

Ahigh quality, nitrocellulose-based, lacquer type

putty for wood specially formulated for easy

application and sanding.

For interior wood surfacesSpot putty - 25 square meter / 4 liters

Full putty - 12 square meter / 4 liters5-10 minutes One (1) hour Recoat after 30 minutes

Apply as is. If necessary,

use BOYSENLacquer

Thinner #50

Put ty knife


1st coat: BOYSENLacquer Primer Surfacer #305 Old finish in bad condition should be stripped. BOYSENPaint and Varnish Remover #141 can be used to totally remove the finish.

2nd coat: BOYSENLacquer Spot Putty #306 If old lacquer finish is in good condition, sand surface. Make sure to clean and dry before coating with BOYSEN Automotive Lacquer #1300.

3rd coat: BOYSENLacquer Primer Surfacer #305

Final coat: BOYSENAutomotive Lacquer #1300 in required coats


BOYSENWater White Clear

Gloss Lacquer #1258

Is the highest grade clear gloss lacquer finish for

a durable finishing for interior woodwork. Its

properties enhance the natural grain of wood.

For lacquer finishing of interior wood

walls, furniture, fixtures, cabinets, doors

and panels.

25-30 sq.m/ gallon / coat 10 minutes 1 hour 1.5 mils / coat Recoat after 30 minutes BOYSENLacquer Thinner#50

by brush or spray

Sealer coat: BOYSENLacquer Sanding Sealer #1254 Repainting:

Final coat: BOYSENWater White Clear Gloss Lacquer #1258 Old lacquer finish in bad condition should be stripped. Prepare to clean and dry before finishing as indicated for new wood.

If old lacquer finish is in good condition, sand and dust surface. Make sure to clean and dry before coating. Apply required finish coats of BOYSEN Water White Clear Gloss Lacq


PAINTING SCHEDULE

PAINTING SCHEDULE

:


BOYSEN Acrytex

An acrylic solvent-based coating that forms a

seamless, non-porous, watertight film that repels

water and prevents seepage. It is noted for its

excellent adhesion and long-termdurabili ty.

Creates a very tight film, serving as a moisturesealant for concrete and a stain inhibitor for

wood.

For newand previously Acrytex-Painted

exterior and interior masonry, wood and

properly primed steel.

textured finish -- 15 -18 square meter / 4

liters / coat plain finish -- 25-30

square meter / 4liters / coat

Thirty (30) minutes Two (2) hours 1.5 mils/coat Two (2) hoursBOYSENAcrytex

Reducer #1750

SOLVENT-BASED ACRYLIC PAINTS


10/15


Plain Finish:

1. Prime surface with BOYSENAcrytexPrimer #1705.

2. Fill hairline cracks and minor surface imperfections with BOYSEN AcrytexCast #1711 using a putty knife.

3. Spot prime puttied portions with BOYSENAcrytexPrimer #1705.

4. Apply 2-3 coats of BOYSENAcrytexTopcoat of desired sheen by brush, roller or spray.

Textured Finish:

1. Prime surface with BOYSENAcrytexPrimer #1705.

2. Spray BOYSENAcrytexCast #1711 with mortar gun. Press Acrytex Cast with wooden roller 10-15 minutes after spraying. (Note: wet wooden roller with BOYSEN Acrytex Reducer #1750 to prevent the roller from sticki ng to the cast).

3. Apply 2-3 coats of BOYSENAcrytexTopcoat of desired sheen by brush, roller or spray.


An acrylic solvent-based putty for correction of

.

. I

.

.

,

. I

. ,

.

. .

. .

SURFACE PREPARATION

PAINTING SCHEDULE

I

BOYSEN Acry tex Cast

#1711

minor surface imperfections when a plain finish

of BOYSENAcrytex Topcoat is desired.

Gives an elegant and durable textured finish

when applied with a mortar gun. It is water tight

thus can repel water and prevent seepage.

Noted for excellent adhesion and long term

durability.

For newand previously painted exterior

and interior masonry, wood and fiber

cement boards. It also acts as a water

repellent. Creates a very tight film,

serving as a moisture sealant for

concrete and a stain inhibitor for wood.

As putty -- 10-12 sq.m./gal/coat

As texture -- 5-6 sq.m./gal/coatThirty (30) minutes Two (2) hours Four (4) hours

Use BOYSEN Acrytex

Reducer #1750 only

by mortar gun (texture) or

putty knife (putty)

Repainting

For surfaces previously painted with latex, enamel or lacquer coatings, scrape to bare substrate and clean surface thoroughly, then followschedule for newpainting.

Plain Finish:

1. Prime bare substrate with BOYSENAcrytex Primer #1705.

2. Putty minor surface imperfections with BOYSENAcrytexCast #1711. Spot prime puttied areas.

3. Brush on BOYSEN AcrytexPri mer #1705 when a high gloss finish on wood is desired.

4. Finish with two (2) coats of BOYSENAcrytex Topcoat to desired sheen.

Textured Finish:

1. Prime bare substrate with BOYSENAcrytexPrimer # 1705.

2. Spray BOYSEN AcrytexCast # 1711 with mortar gun. Press Acrytex Cast with plain wooden roller 10-15 minutes after spraying. Wet wooden roller with water to prevent the roller from sticking to the cast.

3. Finish with two (2) coats of BOYSENAcrytexTopcoat to desired sheen.

PAINTING SCHEDULE

SURFACE PREPARATION

Allownewmasonry to dry for 14 to 28 days under normal weather conditions before painting. No need to treat newmasonry with BOYSEN Masonry Neutralizer #44. Surface to be painted should be clean and dry, free fromoi l, grease, dust, dirt , contaminants, and all loose grit and mortar.


BOYSEN Acry tex Clear

Coat #1700

An acrylic solvent-based coating that has

excellent adhesion, long termdurabilit y and easy

clean- up characteristics, creating a superior

sheen and maximumprotect ion

As a clear coat protection for masonry

and wood surfaces.25 - 30 sq.m. / coat / gal. Thirty (30) minutes Two (2) hours 1.5 mils / coat Two (2) hours

Use BOYSEN

AcrytexTMReducer #1750

only

By brush, roller or spray

Apply 2 to 3 coats of BOYSENAcrytexTMClear #1700 on bare pebble washout or natural stone finished walls by air spray or brush.

For walls with BOYSENMultif leckTM, apply a thin coat by spray if gloss finish is desired.

PAINTING SCHEDULE


11/15


BOYSEN Acqua Epoxy

Atwo-component water based acrylic epoxy

paint that has superior solvent, chemical and

stain resistance ideal for concrete floors and

properly primed metal surfaces. It has the

advantage of easier application and better

weather resistance properties.

For floorings, walls, metal substrates and

other well primed surfaces.25-30 square meter / 4 li ters /coat Thi rty (30) minutes Four (4) hours 1.5 mi ls/coat

Allowfour (4) hours before

recoating. For best results,

recoating should be done

overnight.

Not recommendedpaint brush, roller or airless

spray gun

MIXING RATIO: 4:1, paint to catalyst, respectively

Concrete Flooring:

Finished acid etched surface should have a texture similar to that of 40-60 grit sandpaper. Make sure that the surfaces to be painted are clean and dry.

: .

TWO-COMPONENT EPOXY BASED COATINGS

SURFACE PREPARATION

Remove oil and grease by detergent cleaning. For smooth surfaces, acid etch to improve adhesion. Do this by mixing one (1) part muriatic acid to one (1) part water. Apply over masonry and let stand for 2-3 minutes. Rinse with water to remove residual acid. If possible, rinse by pressure washing.

Caution: Adequate protection and ventilation should be provided when working with acids.

Metal:

Concrete Flooring:

Mix three (3) parts of BOYSENEpoxy Primer White #2200 to one (1) part of its catalyst.

Allowtwenty (20) minutes induction time. Thin 1:1 with BOYSENEpoxy Reducer #55. Apply as primer coating on bare concrete. Let dry overnight.

Metal:

NOTE:

Foot traffic abrasion resistance fully develops after three (3) days of curing. For heavy-duty application, allow seven (7) days of drying.


Ahigh quality, two-component, epoxy-polyamide

systemthat has excellent corrosion resistance

and sealing properties. Highly alkali-resistant so

there is no need for neutralization of new

.

As a topcoat for BOYSENEpoxy Primer

that can be applied on interior surfaces

such as metal, galvanized iron, wood and

.

20-30 square meter / 4 liters / coat 2-3 hours 6-8 hours 1.5 mils/coatBOYSENEpoxy Reducer

#55By paint brush or spray gu

Be sure to wash off surface thoroughly with water. Wipe off surface with rag soaked in paint thinner to remove dust, dirt, grease, oil, wax and other foreign matter. For newG.I. sheets, etch the surface by applying 10%BOYSEN Metal Etching Solution #71 (dilute 1 part of B-71 to 9 parts water).

If repainting on surfaces with alkyd, latex or lacquer-based coatings, scrape off all paint f ilm to bare substrate. Remove oil and grease by detergent cleaning followed by scuff sanding. To remove rust, wire brush or scrape affected areas and apply BOYSEN Metal Etching Solution #71 over rusted portions. Let it stay

off surface thoroughly with water, letting it dry before applying paint. Primer should be applied immediately upon drying of the surface before rust sets in.

PAINTING SCHEDULE

Mix four (4) parts of BOYSENAcqua Epoxy to one (1) part of its catalyst. Allowtwenty (20) minutes induction time. Mixture may gel if not used within 24 hours. Apply three (3) coats as topcoat, all owing for at least 4 hours between coats. For best results, recoating should be done overnight.

Prime bare metal with BOYSENEpoxy Red Oxide Primer #2277 or BOYSENEpoxy Primer Gray #2230. Let dry eight (8) hours before recoating. Alternatively, BOYSEN Primeguard#4310 can be used. Apply a single coat and let dry for 2-4 hours before recoating. Finish with 2-3 coats of BOYSENAcqua Epo

before recoating.

BOYSEN Epoxy Enamel

, ,

.

concrete.

, ,

masonry.

.

MIXING RATIO: 3:1, paint-to-catalyst, respectively

Concrete Flooring:

Finished acid etched texture should be similar to that of 40-60 grit sandpaper. Make sure that the surfaces to be painted are clean and dry.

Caution: Adequate protection and ventilation should be provided when working!

SURFACE PREPARATION

Remove oil and grease by detergent cleaning. For smooth surfaces, acid etch to improve adhesion. Do this by mixing one (1) part muriatic acid to one (1) part water. Apply over masonry and let stand for 2-3 minutes. Rinse with water to remove residual acid. If possible, rinse by pressure washing.


12/15

Metal:

Wipe the surface with rag soaked in paint thinner to remove dust, dirt, grease, oil, wax and other foreign matter. For newG.I . sheets, etch the surface by applying 10%BOYSEN Metal Etching Solution #71 (dilute 1 part of B-71 to 9 parts water).

Concrete Flooring:


Metal:Prime base metal with BOYSENEpoxy Red Oxide Primer #2277 or BOYSENEpoxy Primer Gray #2230. Let dry 8 hours to overnight. Topcoat with 2-3 coats of BOYSEN Epoxy Enamel. Let dry overnight before recoating.

Water Tank (Interior)

. . - . . .

If repainting on surfaces with alkyd or lacquer-based coatings, scrape off all paint film to bare substrate. Remove oil and grease by detergent cleaning followed by scuff sanding. To remove rust, wire brush or scrape affected areas and apply BOYSEN Metal Etching Solution #71 over rusted portions. Let it stay for 10

surface thoroughly with water, letting it dry before applying paint. Primer should be applied immediately upon drying of the surface before rust sets in.

PAINTING SCHEDULE

Allowtwenty (20) minutes induction time. Thin 1:1 with Epoxy Reducer #55. Apply as primer coating on bare concrete floors. Let dry overnight. Mix BOYSEN Epoxy Enamel with its catalyst as with the procedure of the BOYSEN Epoxy Primer. Paint 2-3 coats of this mixture over well-primed surface. Allow 8 hours

rime are su srae wi poxy rimer i e . e ry ours o overnig . opcoa wi - coas o poxy name i e . e ry overnig eore recoaing. uring is sric y seven ( ) ays prior o use o an .

NOTE:

Foot traffic abrasion resistance fully develops after three (3) days of curing. For heavy duty application, allowseven (7) days of drying.

Application of topcoat should be done within 7 days after priming to ensure good intercoat adhesion, otherwise re-application of primer is needed.


BOYSEN Epoxy Primer

Ahigh quality, two-component, epoxy-polyamide

systemthat has exceptional adhesion to

practically any surface including steel tanks,

coastal installations, galvanized iron, pipelines,

aluminum, structural steel, etc. Has excellent

corrosion resistance and sealing properties.

Highly alkali-resistant so there is no need for

neutralization of newconcrete.

As a primer for topcoats of Epoxy Enamel

or Acqua Epoxyto be applied on metal,

galvanized iron, wood and masonry

20-25 square meter / 4 liters / coat 2-3 hours 6-8 hours 1.5 mils/coatBOYSENEpoxy Reducer

#55By Paint brush or spray gu

MIXING RATIO: 3:1, paint-to-catalyst, respectively

Concrete Flooring:

SURFACE PREPARATION

Remove oil and grease by detergent cleaning. For very smooth floors, acid etch smooth surfaces to improve adhesion. Do this by mixing one (1) part muriatic acid to one (1) part water. Apply over masonry and let stand for 2-3 minutes. Rinse with water. If available, rinse by pressure washing. Finished acid etched tex

60 grit sandpaper. Make sure that the surfaces to be painted are clean and dry.


Metal:

Wipe the surface with rag soaked in paint thinner to remove dust, dirt, grease, oil, wax and other foreign matter. For new G.I. sheets, etch the surface by applying 10%BOYSEN Metal Etching Solution #71 (dilute 1 part of B-71 to 9 parts water).

If repainting on surfaces with alkyd or lacquer based coatings, scrape off all paint. Remove oil and grease by detergent cleaning followed by scuff sanding. To remove rust, wire brush or scrape affected areas and apply BOYSEN Metal Etching Solution #71. Let it stay for 10-15 minutes. Be sure to wash off surface t

before applying paint. Primer should be applied immediately after treatment.

PAINTING SCHEDULE


13/15

Concrete Flooring:


Metal:

Prime bare metal BOYSENEpoxy Red Oxide #2277 or BOYSENEpoxy Primer Gray #2230. Let dry eight (8) hours before recoating. Topcoat with 2-3 coats of BOYSEN Acqua Epoxyor BOYSENEpoxy Enamel. Let dry overnight before recoating.

NOTE: For epoxy-primed surfaces, topcoat should be applied not more than seven (7) days after priming to ensure good intercoat adhesion. Otherwise, re-priming is needed.


HudsonPolyurethane Floor Sealer is an

,

.

As a primer for parquet and other wooden

.

. . .

TWO-COMPONENT POLYURETHANE BASED COATINGS

Allowtwenty (20) minutes induction time. Dilute 1:1 ratio with BOYSENEpoxy Reducer #55. Apply as primer coating on bare concrete. Let dry overnight. Topcoat with 2-3 coats of BOYSEN Acqua Epoxyor BOYSENEpoxy Enamel. Let dry overnight before recoating. Let cure for 3 days before allowing foot traf

Hudson Polyurethane Floor

Varnish Sealer

aromatic, two-component urethane sealer to

provide good adhesion of Hudson

Polyurethane Floor Varnish Topcoat.

floors and counter-tops for subsequent

coating of HudsonPolyurethane Floor

Varnish Topcoat (indoor use).

20 - 25 sq.m./4 liters/coat Thirty (30) minutes One (1) hour 1.5 mils/coat Recoat after 6 hoursBy natural hair brush or air

spray

MIXING RATIO:

HudsonPolyurethane Floor Sealer is mixed 3.5 Liters to its 1/2-li ter catalyst. Enough mixture is made for four (4) hours work (maximum). Excess material will gel.

New Wood: Old Wood:

1. Use only kiln dried wood. 1. Remove loose paint to sound surface.

2. Countersink nail heads for putty application. 2. Scuff sand intact filmto provide anchorage for succeeding coats.

3. Sand rough wood until smooth, then dust off before painting. 3. If old coating is oil-based, scrape all existing paint to bare surface.

4. Surface to be painted should be clean and dry, free fromdust, dirt and other foreign matter. 4. Surface to be painted should be clean and dry, free fromdust, dirt and other foreign matter.

1st and 2nd coats: HudsonPolyurethane Floor Varnish Sealer

3rd to 5th: HudsonPolyurethane Floor Varnish Topcoat


Hudson Polyurethane Floor

Varnish Topcoat

HudsonPolyurethane Floor Varnish Topcoat is

an aromatic, two-component, urethane finish for

wooden surfaces that cure to a tough, non-slip,

mar resistant film.

Excellent for wood parquet, counter-

tops, and other wooden floorings (indoor

use).

20 - 25 sq.m./4 liters/coat Thirty (30) minutes One (1) hour 1.5 mils/coat Recoat after 6 hoursHudsonPolyurethane

ReducerBy camel brush or spray

MIXING:

SURFACE PREPARATION

PAINTING SCHEDULE

HudsonPolyurethane Floor Varnish Topcoat is mixed on a 3:1 ratio by volume to its catalyst. Enough material should be made for four hours work (maximum). Excess mixture will gel.

New Wood: Old Wood:

1. Use only kiln dried wood. 1. Remove loose paint to sound surface.

2. Countersink nail heads for putty application. 2. Scuff sand intact filmto provide anchorage for succeeding coats.

3. Sand rough wood until smooth, then dust off before painting. 3. If old coating is oil-based, scrape all existing paint to bare surface.

4. Surface to be painted should be clean and dry, free fromdust, dirt and other foreign matter. 4. Surface to be painted should be clean and dry, free fromdust, dirt and other foreign matter.

SURFACE PREPARATION

PAINTING SCHEDULE

NewWood - Apply 1 to 2 coats of HudsonPolyurethane Floor Varnish Sealer by brush or spray. Follow with 3 coats of HudsonPolyurethane Floor Varnish Topcoat applied by spray. Allow 7 days to fully cure before allowing heavy duty use and 3 days for foot traff ic abrasion.


14/15


BOYSEN Aqu aseal #99

Anon-silicone protective sealer designed to

impart maximumwater repellancy to a wide

variety of above ground masonry and stone

surfaces. It minimizes unsightly efflorescence

and reduces cracking and spalling.

BOYSENAquaseal#99 enhances the

appearance of natural stone.

Functions as a clear penetrating sealer

on porous substrates to repel water and

moisture for brick, stucco, concrete,

hollowblocks, rubble, and sandblast

finish.

8 sq.m/ gallon 2 hours

Not necessary. Use paint

thinner for washing of

tools

by brush (do not spray)

BOYSENAquaseal#99 should be applied liberal ly to saturate the surface. Generous overlapping of passes is recommended until it dri ps down about 6 inches on masonry.


Is a water-based, lowVOCpaint for priming

previously painted masonry surfaces where the

.

As a primer when repainting chalky25-30 sq.m/ gallon 1-2 hours 2 hours

1.25 mils/coatnot necessary by brush/roller

SURFACE PREPARATION CHEMICALS

PAINTING SCHEDULE

I I

BOYSEN Chalk Blocker

#7304

I ,

existing paint fi lmis chalky.

surfaces .

.

(approximately)

For chalking old paint, use Boysen Chalk Blocker #7304 as primer.


BOYSEN Masonry

Neutralizer

Aliquid acidic substance that is to be mixed with

water to neutralize lime activity in new masonry

surfaces.

20 sq.m./gallon of mixture paint brush or roller

MIXING RATIO: 1 part BOYSENMasonry Neutralizer #44 to 16 parts clean water

1st step: Remove oil and grease by detergent cleaning.

2nd step: Apply diluted BOYSEN

Masonry Neutralizer and let stand overnight3rd step: Rough sand surface to remove efflorescence salts



BOYSEN Metal Etching

Solution #71

An acid type metal cleaner and rust converter. It

transforms rust and removes light deposits of

mill oil. B-71 destroys corrosion stimulators and

properly conditions metal surfaces for painting.

As preparation agent for painting on new

galvanized and rusty metal surfaces

25-30 sq.m./gallon of mixture depending

on surface rustinesswater paint brush

PAINTING SCHEDULE

PAINTING SCHEDULE

. I

.

.

. .

MIXING RATIO:

1. For treatment of new G. I. sheets: 1 part of Boysen Metal Etching Solution #71 to 9 parts water.

2. For rust treatment: use pure, limited over stubborn rust only.

NewGalvanized Metal: Rusted Metal Surface:

Step 1: Wipe the surface with rag soaked in paint thinner to remove dust, dirt, grease, oil, wax and other foreign matter. Step 1: Wire brush and scrape loose rust

Step 2: Apply 10%Boysen Metal Etching Solution #71 Step2: Apply pure Boysen Metal Etching Solution #71 on rust.

Step 3: Let stand for 10-15 minutes then wash off wi th water toremove residue. Let dry. Step 3: Let stand for 10-15 minutes then wash off wi th water toremove residue. Let dry.

PAINTING SCHEDULE


15/15

Primer should be applied immediately after treatment.



BOYSEN Paint and Varnish

Remover #141

An effective wax-based paint stripper.

As preparation agent for repainting of

metal, wood and masonry surfaces where

the existing paint needs to be removed.

15-18 sq.m./gallon of mixture depending

on paint reaction.

paint brush. Use rubber

gloves when applying


Aspecial bonding paste that is mixed with

cement and applied on concrete to correct

. I

,

.

For both interior and exterior plastered

concrete, concrete slabs, acotech walls,

reinforced concrete walls, and pre-cast

.

0.4 kg /sq. m. / mm, recommended total

. .

30 min.; allow14 days

Apply with trowel or putty

.

PAINTING SCHEDULE

Apply BOYSENPaint and Varnish Remover #141 on painted surface. When the old paint has wrinkled after approximately 10 minutes, scrape off with the use of spatula or putty knife. Wash off residue by detergent washing followed by solvent washing with BOYSEN Lacquer Thinner.

BOYSENSkimcoat

surface imperfections prior to painting. It repairs

bubbles, honeycomb and concrete defects on

waviness and plumbness up to 4 mmthick.

, , ,

,

concrete surfaces in lieu of cement

plaster to eliminate surface defects and

make the surface smooth and ready for

painting.

. . . ,

thickness is from 0.3 - 4 mm.

.;

before painting

knife.

POTLIFE:Thirty (30) minutes

1. Remove oil, grease, dust, dirt , contaminants, and all loose grit and mortar from the surface.

2. Defects on concrete more than 5 mmthick should be corrected using mechanical sanders/grinders.

3. Moisten the concrete before application.

1. Using a steel trowel, apply the mixture thinly on the surface by pressing the edge of the trowel firmly on the concrete until all areas are covered.

2. Let it dry for at least 30 minutes before applying the second coat (if necessary).

3. If trowel marks are visible, let surface dry for at least 30 minutes before sanding to further smoothen surfaces.

4. No need to neutralize the surface. Allow at least 14 days before painting.

Note: Do not apply on painted surfaces.

APPLICATION

SURFACE PREPARATION

MIXING PROCEDURE: Put BOYSENSkimcoat#7750 on a suitable container (plastic bucket) and mix with cement at 1:1 ratio by weight until a lump-free homogeneous paste is reached. Do not add water. Use portland cement (for ordinary cement color) or white cement (to produce a white finish). No need to ne

Date post:	13-Apr-2018
Category:	Documents
Upload:	aldrich-roswell-ona
View:	331 times
Download:	11 times

Boysen Paints

Documents