BRITISH STANDARD BS EN60617-8:1996IEC 617-8:1996
Graphical symbols for diagrams —
Part 8: Measuring instruments, lamps and signalling devices
The European Standard EN 60617-8:1996 has the status of a British Standard
ICS 01.080.30; 29.020
BS EN 60617-8:1996
This British Standard, having been prepared under the direction of the Electrotechnical Sector Board, was published under the authority of the Standards Board and comes into effect on 15 December 1996
© BSI 10-1998
The following BSI references relate to the work on this standard:Committee reference GEL/3Draft for comment 92/28846 DC
ISBN 0 580 60617 8
Committees responsible for this British Standard
The preparation of this British Standard was entrusted to Technical Committee GEL/3, Documentation and graphical symbols, upon which the following bodies were represented:
British Photographic AssociationConsumer Policy Committee of BSIFederation of the Electronics IndustryGAMBICA (BEAMA Ltd.)Transmission and Distribution Association (BEAMA Ltd.)
Amendments issued since publication
Amd. No. Date Comments
BS EN 60617-8:1996
© BSI 10-1998 i
Contents
PageCommittees responsible Inside front coverNational foreword ii
Foreword 2Text of EN 60617-8:1996 3
BS EN 60617-8:1996
ii © BSI 10-1998
National foreword
This British Standard has been prepared by Technical Committee GEL/3. It is the English language version of EN 60617-8:1996, Graphical symbols for diagrams Part 8: Measuring instruments, lamps and signalling devices published by the European Committee for Electrotechnical Standardization (CENELEC). It is identical with IEC 617-8:1996 published by the International Electrotechnical Commission (IEC).This British Standard replaces BS 3939-8:1985 which is withdrawn.NOTE The French language version of the alphabetic index has not been included.
A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application.
Compliance with a British Standard does not of itself confer immunity from legal obligations.
Summary of pagesThis document comprises a front cover, an inside front cover, pages i and ii, the EN title page, pages 2 to 22 and a back cover.This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover.
EUROPEAN STANDARD
NORME EUROPÉENNE
EUROPÄISCHE NORM
EN 60617-8
June 1996
ICS 01.080.30
Descriptors: Measuring instrument, signal device, electric diagram, electrical symbol
English version
Graphical symbols for diagrams Part 8: Measuring instruments, lamps and signalling
devices(IEC 617-8:1996)
Symboles graphiques pour schémas Partie 8: Appareils de mesure, lampes et dispositifs de signalisation(CEI 617-8:1996)
Graphische Symbole für SchaltpläneTeil 8: Schaltzeichen für Meß, Melde- undSignaleinrichtungen(IEC 617-8:1996)
This European Standard was approved by CENELEC on 1996-03-05.CENELEC members are bound to comply with the CEN/CENELEC InternalRegulations which stipulate the conditions for giving this European Standardthe status of a national standard without any alteration.Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to anyCENELEC member.This European Standard exists in three official versions (English, French,German). A version in any other language made by translation under theresponsibility of a CENELEC member into its own language and notified to theCentral Secretariat has the same status as the official versions.CENELEC members are the national electrotechnical committees of Austria,Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy,Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland andUnited Kingdom.
CENELEC European Committee for Electrotechnical Standardization
Comité, Européen de Normalisation Electrotechnique Europäisches Komitee für Elektrotechnische Normung
Central Secretariat: rue de Stassart 35, B-1050 Brussels
© 1996 Copyright reserved to CENELEC membersRef. No. EN 60617-8:1996 E
EN 60617-8:1996
© BSI 10-19982
Foreword
The text of document 3A/386/FDIS, future edition 2 of IEC 617-8, prepared by SC 3A, Graphical symbols for diagrams, of IEC TC 3, Documentation and graphical symbols, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 60617-8 on 1993-03-05.The following dates were fixed:
Contents
PageIntroduction 3Section 1 Indicating, recording and integrating instruments, general symbols 4Section 2 Examples of indicating instruments 6Section 3 Examples of recording instruments 8Section 4 Examples of integrating instruments 8Section 5 Counting devices 11Section 6 Thermocouples 12Section 7 Telemetering devices 13Section 8 Electric clocks 13Section 9 Miscellaneous measuring elements and instruments 14Section 10 Lamps and signalling devices 15Annex A (informative) Older symbols 18Annex B (informative) English alphabeticindex 21
– latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 1997-02-01
– latest date by which the national standards conflicting with the EN have to be withdrawn (dow) 1997-02-01
EN 60617-8:1996
© BSI 10-1998 3
IntroductionThis part of IEC 617 forms an element of a series which deals with graphical symbols for diagrams. The series consists of the following parts:
— Part 1: General information, general index. Cross-reference tables;— Part 2: Symbol elements, qualifying symbols and other symbols having general application;— Part 3: Conductors and connecting devices;— Part 4: Basic passive components;— Part 5: Semiconductors and electron tubes;— Part 6: Production and conversion of electrical energy;— Part 7: Switchgear, controlgear and protective devices;— Part 8: Measuring instruments, lamps and signalling devices;— Part 9: Telecommunications: Switching and peripheral equipment;— Part 10: Telecommunications: Transmission;— Part 11: Architectural and topographical installation plans and diagrams;— Part 12: Binary logic elements;— Part 13: Analogue elements.
The scope and the normative references for this series are given in IEC 617-1.Symbols have been designed in accordance with requirements given in the future ISO 11714-11). The module size M = 2,5 mm has been used. For better readability smaller symbols in this standard have been enlarged to double size and are marked “200 %” in the symbol column. To save space larger symbols have been reduced to half size and are marked “50 %” in the symbol column. In accordance with the future ISO 11714-1, clause 7, symbol dimensions (for instance height) may be modified in order to make space for a greater number of terminals or for other layout requirements. In all cases, whether the size is enlarged or reduced, or dimensions modified, the thickness of the original line should be maintained without scaling.
The symbols in this standard are laid out in such a way that the distance between connecting lines is a multiple of a certain module. The module 2M has been chosen to provide enough space for a required terminal designation. The symbols have been drawn to a size convenient for comprehension, using the same grid consistently in the representation of all symbols.All symbols are designed within a grid in a computer-aided draughting system. The grid which was used has been reproduced in the background of the symbols.The older symbols which were included in appendix A of the first edition of IEC 617-8 for a transitional period, are no longer part of this second edition, as they will definitely be withdrawn from use.The indexes in Annex B and C include an alphabetic list of symbol names and their corresponding number. The symbol names are based on the description of the symbols of this part. A general index including an alphabetic list of symbols of all parts is given in IEC 617-1.
1) At present, at the stage of Draft International Standard (document 3/563/DIS).
EN
60617-8:1996
4©
BS
I 10-1998
Section 1 — Appareils indicateurs, appareils enregistreurs et computers, symboles généraux
Section 1 — Indicating, recording and integrating instruments, general symbols
1.1 L’astérisque placé à l’intérieur de chacun des symboles de la présente section doit être remplacé:
1.1 The asterisk within the symbols of this section shall be replaced with one of the following:
– soit par le symbole littéral de l’unité de la grandeur mesurée ou l’un de ses multiples ou sous-multiples (voir examples 08-02-01 et 08-02-07);
– the letter symbol for the unit of the quantity measured, or a multiple or sub-multiple thereof (see example 08-02-01 and 08-02-07);
– soit par le symbole littéral de la grandeur mesurée (voir examples 08-02-05 et 08-02-06);
– the letter symbole for the quantity measured (see examples 08-02-05 and 08-02-06);
– soit par une formule chimique (voir example 08-02-13); – a chemical formula (see example 08-02-13);
– soit par un symbole graphique (voir example 08-02-08). – a graphical symbol (see example 08-02-08);
Le symbole ou la formule utilisée doit correspondre à l’information fournie par l’appareil de mesure quels que soient les moyens employés pour obtenir cette information.
The symbol or formula used shall be related to the information displayed by the instrument regardless of the means used to obtain the information.
1.2 Les symboles littéraux d’unité ou de grandeur doivent être choisis parmi ceux figurant dans l’une des parties de la Publication 27 de la CEI: symboles littéraux à utiliser en électrotechnique.
1.2 Letter symbols for units and for quantities shall be selected from one of the parts of IEC Publication 27: Letter symbols to be used in Electrical Technology.
Si aucun symbole littéral de la Publication 27 de la CEI, ni aucune formule chimique ne convient, d’autres symboles littéraux peuvent être utilisés. Leur signification doit, dans ce cas, être indiquée soit sur le schéma, soit sur un document associé.
Provided IEC Publication 27, Letter symbols for chemical elements, do not apply, other letter symbols may be used, if they are explained on the diagram or in referenced documents.
1.3 Lorsque le symbole littéral de l’unité de la grandeur mesurée est utilisé, le symbole littéral de la grandeur peut être nécessaire pour donner une information complémentaire. II convient de le placer sous le symbole littéral de l’unité (voir exemple 08-02-02).
1.3 If the letter symbol for the unit of the quantity measured is used, it may be necessary to show the letter symbol for the quantity as supplementary information. it should be placed below the unit letter symbol (see examples 08-02-02).
Des information complémentaires concernant la grandeur mesurée ainsi que tout symbole distinctif nécessaire peuvent être inscrites sous le symbole littéral de la grandeur.
Supplementary information concerning the quantity measured, and any necessary qualifying symbol may be shown below the quantity letter symbol.
1.4 Pour un appareil indiquant ou enregistrant plus d’une grandeur, les cadres des symboles appropriés doivent être placés de manière contiguê ou en colonne (voir examples 08-03-02 et 08-04-14).
1.4 If more than one quantity is indicated or recorded by an instrument, the appropriate symbol outlines shall be placed attached in line, horizontally or vertically (see example 08-03-02 and 08-04-14).
EN
60617-8:1996
© B
SI 10-1998
5
No. Symbole Symbol Légende Description
08-01-01 Appareil indicateur
L’astérisque doit être remplacé selon les règles données dans l’article 1.1
Indicating instrument
The asterisk shall be replaced in accordance with the rules in Clause 1.1
08-01-02 Appareil enregistreur
L’astérisque doit être remplacé selon les règles données dans l’article 1.1
Recording instrument
The asterisk shall be replaced in accordance with the rules in Clause 1.1
08-01-03 Appareil intégrateur par exemple compteur (d’énergie électrique)
L’astérisque doit être remplacé selon les règles données dans l’article 1.1
Ce symbole est également applicable à un appareil à distance répétiteur d’un compteur.Comme exemple, voir le symbole 08-04-11.
Ce symbole peut être associé à celui d’un enregistreur pour représenter un appareil combiné. Comme exemple, voir le symbole 08-04-14
Les symboles de la section 5 de la CEI 617-2 peuvent être utilisés pour spécifier le sens du transit de l’énergie.Comme exemples, voir les symboles 08-04-04 à 08-04-07.
Le nombre de rectangles supérieurs indique le nombre de sommations différentes d’un compteur à tarifs multiples.Comme exemple, voir le symbole 08-04-08.
Integrating instrument for example energy meter
The asterisk shall be replaced in accordance with the rules given in Clause 1.1
This symbol may also be used for a remote instrument which repeats a reading transmitted from an integrating meter.For example, see symbol 08-04-11.
This symbol may be combined with that for a recording instrument to represent a combined instrument. For example, see symbol 08-04-14.
Symbols from section 5 from IEC 617-2 may be used to specify the direction of energy flow.
For examples, see symbols 08-04-04 to 08-04-07.
The number of rectangles at the top of the symbol indicates the number of different summations by a multirate meter.For example, see symbol 08-04-08.
EN
60617-8:1996
6©
BS
I 10-1998
Section 2 — Exemples d’appareils indicateurs Section 2 — Example of indicating instruments
No. Symbole Symbol Légende Description
08-02-01 Voltmèter Voltmeter
08-02-02 Ampèremètre de courant réactif Reactive current ammeter
08-02-03 Indicateur de maximum de puissance active asservi à un compteur d’énergie
Maximum demand indicator actuated by an integrating meter
08-02-04 VarmètreIndicateur de puissance réactive
Varmeter
08-02-05 Cos ϕ mètre
Indicateur du facteur de puissance
Power-factor meter
08-02-06 PhasemètreIndicateur de déphasage
Phase meter
08-02-07 Fréquencemètre Frequency meter
08-02-08 Synchronoscope Synchronoscope
EN
60617-8:1996
© B
SI 10-1998
7
08-02-09 Ondemètre Wavemeter
08-02-10 Oscilloscope Oscilloscope
08-02-11 Voltmètre différentiel Differential voltmeter
08-02-12 Galvanomètre Galvanometer
08-02-13 Salinomètre Salinity meter
08-02-14 ThermomètrePyromètre
ThermometerPyrometer
08-02-15 Tachymètre Tachometer
No. Symbole Symbol Légende Description
EN
60617-8:1996
8©
BS
I 10-1998
Section 3 — Exemples d’appareils enregistreurs Section 3 — Examples of recording instruments
No. Symbole Symbol Légende Description
08-03-01 Wattmètre enregistreur Recording wattmeter
08-03-02 Enregistreur combiné wattmètre et varmètre Combined recording wattmeter and varmeter
08-03-03 Oscillographe Oscillograph
Section 4 — Exemples de compteurs Section 4 — Examples of integrating instrumentsNo. Symbole Symbol Légende Description
08-04-01 HeuremètreCompteur horaire
Hour meterHour counter
08-04-02 Ampèreheuremètre Ampere-hour meter
08-04-03 Compteur d’énergie activeWattheuremètre
Watt-hour meter
EN
60617-8:1996
© B
SI 10-1998
9
08-04-04 Compteur d’énergie mesurant l’énergie dans un seul sens Watt-hour meter, measuring energy transmitted in one direction only
08-04-05 Compteur d’énergie reçue du jeu de barres Watt-hour meter, counting the energy flow from the busbars
08-04-06 Compteur d’énergie délivrée au jeu de barres Watt-hour meter, counting the energy flow towards the busbars
08-04-07 Compteur d’énergie échangée (en liaison avec le jeu de barres)
Watt-hour meter, counting in both energy flow directions (towards or from bus bars)
08-04-08 Compteur d’énergie à tarifs multiples, figuré pour double tarif
Multi-rate watt-hour meter, two-rate shown
08-04-09 Compteur d’énergie active à dépassement de puissance Excess watt-hour meter
08-04-10 Compteur d’énergie active avec émetteur Watt-hour meter with transmitter
No. Symbole Symbol Légende Description
EN
60617-8:1996
10©
BS
I 10-1998
08-04-11 Répétiteur d’un compteur d’énergie active Slave watt-hour meter (repeater)
08-04-12 Répétiteur d’un compteur d’énergie active avec dipositif d’impression
Slave watt-hour meter (repeater) with printing device
08-04-13 Compteur d’énergie active avec indication du maximum de la puissance moyenne
Watt-hour meter with maximum demand indicator
08-04-14 Compteur d’énergie active avec enregistrement du maximum de la puissance moyenne
Watt-hour meter with maximum demand recorder
08-04-15 VarheuremètreCompteur d’énergie réactive
Var-hour meter
No. Symbole Symbol Légende Description
EN
60617-8:1996
© B
SI 10-1998
11
Section 5 — Dispositifs de comptage Section 5 — Counting devices
No. Symbole Symbol Légende Description
08-05-01 Fonction de comptage d’un nombre d’évènements, symbole distinctif
Counting function of a number of events, qualifying symbol
08-05-02 Compteur d’impulsions électriques Pulse meter (electrically-operated counting device)
08-05-03 Compteur d’impulsions électriques avec mise à n manuelle (mise à zéro si n = 0)
Pulse meter manually pre-set to n (reset if n = 0)
08-05-04 Compteur d’impulsions électriques avec mise à 0 électrique
Pulse meter electrically reset to 0
08-05-05 Compteur d’impulsions électriques à plusieurs contacts
Les contacts sont fermés respectivement pour chaque unité (100), dizaine (101), centaine (102) et millier (103) d’évènements qu’enregistre le dispositif de comptage
Pulse meter with multiple contacts
Respective contacts close once at every unit (100), ten (101), hundred (102), thousand (103) events registered by the counter
08-05-06 Dispositif de comptage commandé par came et commandant la fermeture d’un contact tous les n évènements
Counting device, cam driven and closing a contact for each n events
EN
60617-8:1996
12©
BS
I 10-1998
Section 6 — Thermocouples Section 6 — Thermocouples
No. Symbole Symbol Légende Description
08-06-01 Forme 1Form 1
Thermocouple, figuré avec les symboles de polarité Thermocouple, shown with polarity symbols
08-06-02 Forme 2Form 2
Thermocouple avec indication de polarité par un renforcement du trait représentant le pôle négatif
Thermocouple with direct indication of polarity, the negative pole being represented by the thick line
08-06-03 Thermocouple à élément chauffant non isolé
L’élément chauffant peut être représenté par le symbole 05-07-07 au lieu du symbole 05-07-06
Thermocouple with non-insulated heating element
Symbol 05-07-07 may be used to represent the heating element instead of symbol 05-07-06
08-06-04 Forme simpliféeSimplified form
08-06-05 Thermocouple à élément chauffant isolé Thermocouple with insulated heating element
08-06-06 Forme simpliféeSimplified form
EN
60617-8:1996
© B
SI 10-1998
13
Section 7 — Dispositifs de télémesure Section 7 — Telemetering devices
No. Symbole Symbol Légende Description
08-07-01 Convertisseur de signal, symbole général Signal translator, general symbol
08-07-02 supprimédeleted
Transféré à Annexe A: 08-A1-01 Transferred to Annex A: 08-A1-01
08-07-03 supprimédeleted
Transféré à Annexe A: 08-A1-02 Transferred to Annex A: 08-A1-02
Section 8 — Horloges électriques Section 8 — Electric clocks
No. Symbole Symbol Légende Description
08-08-01 Horloge, symbole généralHorloge secondaire
Clock, general symbolSecondary clock
08-08-02 Horloge-mère Master clock
08-08-03 Horloge à contact Clock with contact
EN
60617-8:1996
14©
BS
I 10-1998
Section 9 — Appareils de mesure et instruments divers
Section 9 — Miscellaneous measuring elements and instruments
No. Symbole Symbol Légende Description
08-09-01 supprimédeleted
Transféré à Annexe A: 08-A2-01 Transferred to Annex A: 08-A2-01
08-09-02 Dispositif syn chrone, symbole général L’astérisque doit être remplacé par des lettres caractérisant la fonction de l’élément considéré. Suivant les fonctions, ces lettres sont les suivantes:
Première lettre Fonction
C CommandeT CoupleR Transformateur de
coordonnées
Lettre suivante Fonction
D DifférentielR RécepteurT TransformateurX TransmetteurB Enroulement de stator
orientable
Le cercle intérieur du symbole représente le rotor et le cercle extérieur représente le stator ou, dans certains cas, un enroulement extérieur orientable
Synchronous device, general symbol
The asterisk shall be replaced by the appropriate letters for the particular synchronous device being symbolized. The letters to be used according to the function are as follows:
First letter Function
C ControlT TorqueR Resolver
Succeeding letter Function
D DifferentialR ReceiverT TransformerX TransmitterB Rotatable stator
winding
In the symbol, the inner circle represents the rotor and the outer circle the stator or, in certain instances, a rotatable outer winding
08-09-03 Transmetteur de couple Torque transmitter
08-09-04 Gyro Gyro
08-09-05 supprimédeleted
Transféré à Annexe A: 08-A2-02 Transferred to Annex A: 08-A2-02
08-09-06 supprimédeleted
Transféré à Annexe A: 08-A2-03 Transferred to Annex A: 08-A2-03
EN
60617-8:1996
© B
SI 10-1998
15
08-09-07 supprimédeleted
Transféré à Annexe A: 08-A2-04 Transferred to Annex A: 08-A2-04
08-09-08 supprimédeleted
Transféré à Annexe A: 08-A2-05 Transferred to Annex A: 08-A2-05
Section 10 — Lampes et dispositifs de signalisation Section 10 — Lamps and signalling devices
No. Symbole Symbol Légende Description
08-10-01
200%
Lampe, symbols généralLampe de signalisation, symbole général
Si l’on désire préciser la couleur de la lampe, on place, au voisinage du symbole, l’une des indications suivantes:
RD = rougeYE = jauneGN = vertBU = bleuWH = blanc
Si l’on désire préciser le type de la lampe, on place, au voisinage du symbole, l’une des indications suivantes:
Ne = néonXe = xénonNa = vapeur de sodiumHg = mercureI = iodeIN = incandescenceEL = électroluminescenceARC = arcFL = fluorescenceIR = infrarougeUV = ultravioletLED = diode électroluminescente
Lamp, general symbolSignal lamp, general symbol
If it is desired to indicate the colour, a notation according to the following code is placed adjacent to the symbol:
RD = redYE = yellowGN = greenBU = blueWH = white
If it is desired to indicate the type of lamp, a notation according to the following code is placed adjacent to the symbol:
Ne = neonXe = xenonNa = sodium vapourHg = mercuryI = iodineIN = incandescentEL = electroluminescentARC = arcFL = fluorescentIR = infra-redUV = ultra-violetLED = light emitting diode
08-10-02
200%
Lampe de signalisation, type clignotant Signal lamp, flashing type
No. Symbole Symbol Légende Description
EN
60617-8:1996
16©
BS
I 10-1998
08-10-03 Voyant électromécanique Indicator, electromechanicalAnnunciator element
08-10-04 Indicateur électromécanique de position avec une position hors courant et deux positions significatives
Electromechanical position indicator with one deenergized and two operated positions
08-10-05 Avertisseur sonoreKlaxon
Horn
08-10-06 Forme préferéePreferred form
Sonnerie Bell
08-10-07 supprimé
deleted
Transféré à Annexe A: 08-A3-01 Transferred to Annex A: 08-A3-01
08-10-08 sonnerie à un coup single-stroke bell
08-10-09 Sirène Siren
08-10-10 Forme préferéePreferred form
Ronfleur Buzzer
08-10-11 supprimé
deleted
Transféré à Annexe A: 08-A3-01 Transferred to Annex A: 08-A3-01
No. Symbole Symbol Légende Description
EN
60617-8:1996
© B
SI 10-1998
17
08-10-12 Sifflet à commande électrique Whistle, electrically operated
08-10-13 Lampe de signalisation alimentée par transformateur incorporé
Indicator lamp energized by a built-in transformer
No. Symbole Symbol Légende Description
EN
60617-8:1996
18©
BS
I 10-1998
Annexe A (informative) Anciens symboles Annex A (informative) Older symbolsCette annexe contient une sélection de symboles normalisés dans la CEI 617-8 (1983) qui sont maintenant supprimés. Ces symboles figurent ici seulement afin de faciliter la compréhension des schémas anciens.
This annex contains symbols standardized in IEC 617-8 (1983), which are now deleted. They are shown here for information purposes only to facilitate the comprehension of older diagrams.
(Dans cette annexe, les numéros de la publication de 1983 sont mis entre parenthèses.) (In this annex the numbering from 1983-edition is quoted in parentheses.)
A1 — Dispositifs de telémésure A1 — Telemetering devices
No. Symbole Symbol Légende Description
08-A1-01 Emetteur de télémesure Telemetering transmitter
(08-07-02)
08-A1-02 Récepteur de télémesure Telemetering receiver
(08-07-03)
EN
60617-8:1996
© B
SI 10-1998
19
A2 — Appareils de mesure et instruments divers A2 — Miscellaneous measuring elements and instruments
No. Symbole Symbol Légende Description
08-A2-01 Détecteur de température à boucle continue, par exemple détection du feu
Continuous loop fire detectorContinuous loop temperature sensor, for example, fire detection
(08-09-01)
08-A2-02 Transmetteur de position angulaire ou de pression, type courant continu
Angular position or pressure transmitter, Desynn type (d.c. type)
(08-09-05)
08-A2-03 Indicateur de position angulaire ou de pression, type “courant continu”
Angular position or pressure indicator, Desynn type (d.c. type)
(08-09-06)
08-A2-04 Transmetteur de position angulaire ou de pression, type à induction
Angular position or pressure transmitter, inductor type
(08-09-07)
08-A2-05 Indicateur de position angulaire ou de pression, type à induction
Angular position or pressure indicator, inductor type
(08-09-08)
EN
60617-8:1996
20©
BS
I 10-1998
A3 — Lampes et dispositifs de signalisation A3 — Lamps and signalling devices
No. Symbole Symbol Légende Description
08-A3-01 Autre formeOther form
Sonnerie Bell
(08-10-07)
08-A3-02 Autre formeOther form
Ronfleur Buzzer
(08-10-11)
EN
60617-8:1996
© B
SI 10-1998
21
Annex B (informative) English alphabetic index
Ammeter, reactive current 08-02-02Ampere-hour meter 08-04-02Annunciator element 08-10-03Bell 08-10-06Bell, single-stroke 08-10-08Buzzer 08-10-10Cam driven counting device 08-05-06Clock, electric, with contact 08-08-03Clock, electric, master 08-08-02Clock, electric 08-08-01cosϕ meter, Power-factor meter 08-02-05Counting device, cam driven 08-05-06Counting device, pulse metre (electrically-operated) 08-05-02Counting device, pulse meter electrically reset to 0 08-05-04Counting device, pulse metre with multiple contacts 08-05-05Counting device, pulse metre manually pre-set to n 08-05-03Counting function, qualifying symbol 08-05-01Differential voltmeter 08-02-11Electromechanical position indicator 08-10-04Energy meter 08-01-03Excess watt-hour metre 08-04-09Flashing type signal lamp 08-10-02Frequency metre 08-02-07Galvanometer 08-02-12Gyro 08-09-04Horn 08-10-05Hour counter 08-04-01Hour meter 08-04-01Indicating instrument 08-01-01Indicating instrument, power-factor meter 08-02-05Indicator lamp energized by a built-in transformer 08-10-13Instrument, indicating 08-01-01Instrument, measuring 08-01-01Instrument, recording 08-01-02Integrating instrument 08-01-03Integrating instrument, hour meter 08-04-01
Lamp 08-10-01Lamp, indicator, energized by a built-in transformer 08-10-13Lamp, signal 08-10-01Lamp, signal, flashing type 08-10-02Master clock 08-08-02Maximum demand indicator 08-02-03Maximum demand indicator, watt-hour meter 08-04-13Maximum demand recorder, watt-hour meter 08-04-14Measuring element/instrument, gyro 08-09-04Measuring element/instrument, torque transmitter 08-09-03Measuring instrument 08-01-01Measuring instrument, energy meter 08-01-03Multi-rate watt-hour meter 08-04-08Oscillograph 08-03-03Oscilloscope 08-02-10Phase metre 08-02-06Position indicator, electromechanical 08-10-04Power-factor meter 08-02-05Pulse meter (electrically-operated) 08-05-02Pulse meter electrically reset to 0 08-05-04Pulse meter manually pre-set to n 08-05-03Pulse meter with multiple contacts 08-05-05Pyrometer 08-02-14Reactive current ammeter 08-02-02Recording instrument 08-01-02Recording wattmeter 08-03-01Repeater with printing device 08-04-12Salinity meter 08-02-13Secondary clock 08-08-01Signal lamp 08-10-00Signal lamp, flashing type 08-10-02Signal translator 08-07-01Single-stroke bell 08-10-08Siren 08-10-09Slave watt-hour meter (repeater) 08-04-11Salve watt-hour meter(repeater) with printing device 08-04-12
EN
60617-8:1996
22©
BS
I 10-1998
Synchronoscope 08-02-08Synchronous device 08-09-02Tachometer 08-02-15Telemetring device, signal translator 08-07-01Thermocouple 08-06-01Thermocouple with insulated heating element 08-06-05Thermocouple with non-insulated heating element 08-06-03Thermometer 08-02-14Torque transmitter 08-09-03Translator, signal 08-07-01Transmitter, torque 08-09-03Transmitter, watt-hour meter 08-04-10Var-hour meter 08-04-15Varmeter 08-02-04Varmeter and wattmeter, combined, recording 08-03-02Voltmeter 08-02-01Voltmeter, differential 08-02-11Watt-hour meter 08-04-03Watt-hour meter with maximum demand indicator 08-04-13Watt-hour meter with maximum demand recorder 08-04-14Watt-hour meter with transmitter 08-04-10Watt-hour meter, counting in both energy flow
directions (towards or from bus bars) 08-04-07Watt-hour meter, counting the energy flow from the
busbars 08-04-05Watt-hour meter, counting the energy flow towards
the busbars 08-04-06Watt-hour meter, excess 08-04-09Watt-hour meter, measuring energy transmitted in one
direction only 08-04-04Watt-hour meter, multi rate 08-04-08Watt-hour meter, slave (repeater) 08-04-11Wattmeter and varmeter, combined, recording 08-03-02Wattmeter, recording 08-03-01Wavemeter 08-02-09Whistle, electrically operated 08-10-12
23blank
BSI389 Chiswick High RoadLondonW4 4AL
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
BSI Ð British Standards Institution
BSI is the independent national body responsible for preparing British Standards. Itpresents the UK view on standards in Europe and at the international level. It isincorporated by Royal Charter.
Revisions
British Standards are updated by amendment or revision. Users of British Standardsshould make sure that they possess the latest amendments or editions.
It is the constant aim of BSI to improve the quality of our products and services. Wewould be grateful if anyone finding an inaccuracy or ambiguity while using thisBritish Standard would inform the Secretary of the technical committee responsible,the identity of which can be found on the inside front cover. Tel: 020 8996 9000.Fax: 020 8996 7400.
BSI offers members an individual updating service called PLUS which ensures thatsubscribers automatically receive the latest editions of standards.
Buying standards
Orders for all BSI, international and foreign standards publications should beaddressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001.
In response to orders for international standards, it is BSI policy to supply the BSIimplementation of those that have been published as British Standards, unlessotherwise requested.
Information on standards
BSI provides a wide range of information on national, European and internationalstandards through its Library and its Technical Help to Exporters Service. VariousBSI electronic information services are also available which give details on all itsproducts and services. Contact the Information Centre. Tel: 020 8996 7111.Fax: 020 8996 7048.
Subscribing members of BSI are kept up to date with standards developments andreceive substantial discounts on the purchase price of standards. For details ofthese and other benefits contact Membership Administration. Tel: 020 8996 7002.Fax: 020 8996 7001.
Copyright
Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, ofthe publications of the international standardization bodies. Except as permittedunder the Copyright, Designs and Patents Act 1988 no extract may be reproduced,stored in a retrieval system or transmitted in any form or by any means ± electronic,photocopying, recording or otherwise ± without prior written permission from BSI.
This does not preclude the free use, in the course of implementing the standard, ofnecessary details such as symbols, and size, type or grade designations. If thesedetails are to be used for any other purpose than implementation then the priorwritten permission of BSI must be obtained.
If permission is granted, the terms may include royalty payments or a licensingagreement. Details and advice can be obtained from the Copyright Manager.Tel: 020 8996 7070.